This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete operating instructions, refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation. Device Specifications: Device Type: Manufacturer: Firmware Version: Model(s): Video Conference Tandberg N/A C20 Minimum Software and Firmware Requirements: IP Link Compiler IP Link Firmware GC Version 1.5.1 1.15 3.3.1 Version History: Driver Version Date Notes 4 3/9/2012 Updated to current video conference standards. 3 3/14/2011 Added Layout, Reboot, IR Remote Emulation, Call Status Call Type, and Default Call Protocol. 2 10/24/2010 Added Presentation Mode. 1 1/5/2010 Initial version. Page 1 of 5
Driver Notes: All menu navigation, Dial keypad, Volume(Step), Hook End Call, Quick Keys, IR Remote Emulation, and Presentation Execute commands simulate the IR codes of the remote. The star (*) is also used as a period (.) for the device. Driver is based off of TC4.2 protocol. Device should have software version TC4.2 or higher loaded in order for everything in the driver to function properly. Pan-Tilt (Near), Zoom Control (Near), Focus (Near), Pan-Tilt (Far), and Zoom (Far) use press-release functionality. Stop command is used for configuration purposes. Control Commands & States: Answer Answer Reject Auto Answer On Off Auto Focus Execute Camera ID 1-7 Camera Preset Recall 1-15 Camera Preset Recall (Far) 1-15 Camera Preset Recall (Near) 1-15 Camera Preset Save (Far) 1-15 Camera Preset Save (Near) 1-15 Default Call Protocol SIP H323 Dial Keypad 0-9 * Delete #. Display Mode Dual Single Focus (Near) Near Far Stop Hook End Call Call Join On Off Input (Far) 1-15 Input (Near) 1-2 IR Remote Emulation 0-9 Delete Call Disconnect Down F1 F2 F3 F4 Page 2 of 5
IR Remote Emulation (Continued) F5 Grab Home Layout Left Mute Mic Off OK Phonebook Presentation Right Selfview # Aux Camera Doc Camera PC VCR * Up Volume Down Volume Up Zoom In Zoom Out. Layout Auto Equal Full Screen Pres. Large Speaker Pres. Small Speaker Menu Navigation Up Down Left Right OK Menu Mic 1 On Off Mic 2 On Off Mic 1 Level 1 to 24 steps of 1 Mic 2 Level 1 to 24 steps of 1 Pan-Tilt (Far) Up Down Left Right Stop Pan-Tilt (Near) Up Down Left Right Stop Picture In Picture On Off Power Control On Off Presentation Start Stop Execute Presentation Source 1 2 Quick Keys 1-5 Reboot Execute Selfview On Off Page 3 of 5
Sleep Timer 1-480 Source Input 1 HDMI Input 2 DVI Input 2 HDMI Transmit Mute On Off Volume (Discrete) 0 to 100 in steps of 1 Volume (Step) Down Up Zoom (Far) In Out Stop Zoom (Near) In Out Stop Status Available: Auto Answer On Off Call Setup Mode Direct Gatekeeper Call Status Dialing Connecting Connected Idle Ringing Status Unavailable Not In Call Connection Status Connected Disconnected Display Mode Dual Single Input (Near) 1-2 Power Control On Off Selfview On Off Transmit Mute On Off Volume (Discrete) 0 to 100 in steps of 1 Page 4 of 5
Network communication: When configuring the Ethernet driver, be sure device settings match that of the GC configuration. Port Type: Logon Credentials Supported: Default User Name: Default Password: Ethernet Yes admin Default Port: 23 Multi-Connection Yes Capable: Port Changeable: No TANDBERG Ethernet Driver Configuration Description: Please refer to user manual for settings and changes to the network communication parameters such as: User Name and Passwords. Notes for the Device: Telnet mode must be set to On by an admin in order to have open communication with the driver. Page 5 of 5