This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete operating instructions, refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation. Device Specifications: Device Type: Video Conference Manufacturer: Tandberg Firmware Version: F6.1 Model(s): Edge 95 MXP, Edge 85 MXP, Edge 75 MXP Minimum Software and Firmware Requirements: IP Link Compiler IP Link Firmware GC Version 1.6.0 1.17 3.5.1 Version History: Driver Version Date Notes 6 2/20/2014 Extron Certified. Added Call Status 5 3/14/2013 Extron Certified. Added Dialing Feedback. 4 8/16/2011 Extron Certified. Added Layout and IR Remote Emulation commands. 3 6/7/2011 Extron Certified. Added Video Input and Dual Video commands. 2 1/13/2010 Extron Certified. Added Camera ID for auxiliary camera control. Added Power control. Added Auto Focus. Tested on Edge 95. 1 10/8/2009 Initial Certified Version. Tested on Edge 95 Page 1 of 5
Driver Notes: The driver includes optimization to the features listed below: a. Dynamic Text b. Dialing Feedback c. Volume Asterik(*) is also used as a period. Dialing Configuration: The Keypad is configured to display the digits on the field located at the top of the page. When the desired number is entered, press the Call button and that will connect you with the number you entered. When in a call, the keypad will be used the same as the DTMF tone where each number press will get sent out immediately. The Delete button will delete the last number displayed on the touch panel and is configured with the press/repeat functionality. The Clear button will clear all numbers entered. The Label on the top of the page, Please enter a number and press Call, is configured in GUI Configurator with an ID of 50000-50020 and with the Dynamic text parameter enabled. Page 2 of 5
Control Commands & States: Auto Answer On Off Mute Camera ID 1-13 Dial Keypad 0-9 * #. Delete Clear Display Mode Single Dual Dynamic Text ID 50000 50020 Dual Video** Start Stop Focus (Far) Near Far Focus (Near)* Near Far Auto Stop Hook On Off Input (Far) 1-5 Input (Near) 1-5 IR Remote Emulation 0-9 * # Connect Disconnect Up Down Right Left Selfview Layout Phonebook Cancel Mic Off Presentation Volume Up Volume Down OK Zoom In Zoom Out Grab Layout Execute Menu Navigation Up Down Left Right Enter Cancel Phonebook Microphone Mute On Off Pan-Tilt (Far) Up Down Left Right Page 3 of 5
Continued Pan-Tilt (Near)* Up Left Right Down Stop Picture In Picture On Off Auto Power Control On Off Preset Recall (Far) 1-15 Preset Recall (Near) 1-15 Preset Save (Far) 1-15 Preset Save (Near) 1-15 Selfview Off/On Video Input 1-6 Volume (Discrete) 0 to 21 in steps of 1 Volume (Step) Up Down Zoom (Far) In Out Zoom (Near)* In Out Stop *Will control camera of the selected camera ID **Select Video Input before sending Dual Video command. Status Available: Auto Answer On Off Mute Call Status Status Unavailable Not In Call Connected Ringing Connection Status Connected Disconnected Display Mode Single Dual Hook On Off Input (Near) 1-5 Microphone Mute On Off Picture In Picture On Off Auto Power Control On Off Volume (Discrete) 0 to 21 in steps of 1 Page 4 of 5
Network communication: When configuring the Ethernet driver, be sure device settings match that of the GC configuration. Port Type: Ethernet Default Password: TANDBERG Default Port: 23 Multi-Connection Yes Capable: Port Changeable: No Logon Credentials Yes Supported: Ethernet Driver Configuration Description: Notes for the Device: Device can support up to 13 cameras if Tandberg video switchers are used. Page 5 of 5