Basic voltmeter use. Resources and methods for learning about these subjects (list a few here, in preparation for your research):



Similar documents
Simple circuits worksheet

Parallel DC circuits

Elementary circuits. Resources and methods for learning about these subjects (list a few here, in preparation for your research):

RTD and thermocouple circuits, with millivolt calculations

Ammeter design. Resources and methods for learning about these subjects (list a few here, in preparation for your research):

Basic circuit troubleshooting

DC mesh current analysis

Parallel DC circuits

Experiment 4 ~ Resistors in Series & Parallel

Electrical Fundamentals Module 3: Parallel Circuits

Capacitors. Resources and methods for learning about these subjects (list a few here, in preparation for your research):

Energy, Work, and Power

Measuring Electric Phenomena: the Ammeter and Voltmeter

Lab 3 - DC Circuits and Ohm s Law

6 Series Parallel Circuits

Student Exploration: Circuits

Fig. 1 Analogue Multimeter Fig.2 Digital Multimeter

Voltage, Current, and Resistance

Essential Electrical Concepts

Inductors. Resources and methods for learning about these subjects (list a few here, in preparation for your research):

Resistors in Series and Parallel Circuits

Current Electricity Lab Series/Parallel Circuits. Safety and Equipment Precautions!

What is a multimeter?

Series and Parallel Resistive Circuits Physics Lab VIII

Voltage/current converter opamp circuits

Experiment #5, Series and Parallel Circuits, Kirchhoff s Laws

ANALOG AND DIGITAL METERS ANALOG VS. DIGITAL METERS VOLTMETERS ANALOG AND DIGITAL

Series-parallel DC circuits

FB-DC3 Electric Circuits: Series and Parallel Circuits

ELECTRICAL CIRCUITS. Electrical Circuits

Wire types and sizes

AP Physics Electricity and Magnetism #4 Electrical Circuits, Kirchoff s Rules

Design Project: Power inverter

PHYSICS 111 LABORATORY Experiment #3 Current, Voltage and Resistance in Series and Parallel Circuits

Lab E1: Introduction to Circuits

AC generator theory. Resources and methods for learning about these subjects (list a few here, in preparation for your research):

Differential transistor amplifiers

Potentiometers. Resources and methods for learning about these subjects (list a few here, in preparation for your research):

Resistance, Ohm s Law, and the Temperature of a Light Bulb Filament

Chapter 7 Direct-Current Circuits

Lesson Plan. Parallel Resistive Circuits Part 1 Electronics

EXPERIMENT 7 OHM S LAW, RESISTORS IN SERIES AND PARALLEL

Transformer circuit calculations

Maximum value. resistance. 1. Connect the Current Probe to Channel 1 and the Differential Voltage Probe to Channel 2 of the interface.

Physics 3330 Experiment #2 Fall DC techniques, dividers, and bridges R 2 =(1-S)R P R 1 =SR P. R P =10kΩ 10-turn pot.

OHM S LAW AND RESISTANCE

Sum-of-Products and Product-of-Sums expressions

Lab 1: DC Circuits. Student 1, Partner : Student 2, student2@ufl.edu

The Electrical Properties of Materials: Resistivity

Table of Contents. The Basics of Electricity 2. Using a Digital Multimeter 4. Testing Voltage 8. Testing Current 10. Testing Resistance 12

GROUND DETECTION CIRCUITS FOR STATIONARY APPLICATIONS (IN PLAIN DOWN TO EARTH LANGUAGE)

13.10: How Series and Parallel Circuits Differ pg. 571

Lab 2: Resistance, Current, and Voltage

DC Circuits (Combination of resistances)

HOW TO USE MULTIMETER. COMPILE BY: Dzulautotech

Electrical Circuit Theory

Ohm's Law and Circuits

Using an Oscilloscope

Objectives 200 CHAPTER 4 RESISTANCE

Electrical Diagnostic Tools

COMPOUND CIRCUITS. Voltage (volts) Across Bulb B. Across the Battery. Across Bulb A. Current (amperes) Between A & B. Between Battery & B

Light Bulbs in Parallel Circuits

Parallel Circuits. Objectives After studying this chapter, you will be able to answer these questions: 1. How are electrical components connected

Tristan s Guide to: Solving Parallel Circuits. Version: 1.0 Written in Written By: Tristan Miller Tristan@CatherineNorth.com

Cornerstone Electronics Technology and Robotics I Week 15 Combination Circuits (Series-Parallel Circuits)

The Electrical Control of Chemical Reactions E3-1

People s Physics Book

CHAPTER 28 ELECTRIC CIRCUITS

Odyssey of the Mind Technology Fair. Simple Electronics

Circuit symbol. Each of the cells has a potential difference of 1.5 volts. Figure 1. Use the correct answer from the box to complete the sentence.

Experiment: Series and Parallel Circuits

Measurement of Capacitance

Sources of electricity

Sources of electricity

School of Engineering Department of Electrical and Computer Engineering

Three-phase AC circuits

Your Multimeter. The Arduino Uno 10/1/2012. Using Your Arduino, Breadboard and Multimeter. EAS 199A Fall Work in teams of two!

Capacitive reactance

Kirchhoff s Laws Physics Lab IX

Constant Current Electronic Power Supply Load By Jeff K. Steinkamp N7YG April 3, 2012

Series and Parallel Resistive Circuits

Tristan s Guide to: Solving Series Circuits. Version: 1.0 Written in Written By: Tristan Miller Tristan@CatherineNorth.com

Electromechanical relay logic

Objectives: Part 1: Build a simple power supply. CS99S Laboratory 1

Series and Parallel Circuits

Tutorials Drawing a 555 timer circuit

THE BREADBOARD; DC POWER SUPPLY; RESISTANCE OF METERS; NODE VOLTAGES AND EQUIVALENT RESISTANCE; THÉVENIN EQUIVALENT CIRCUIT

V out. Figure 1: A voltage divider on the left, and potentiometer on the right.

INTRODUCTION TO THE GAS JOBS SELECTION TEST BATTERY

Solutions to Bulb questions

Experiment #3, Ohm s Law

Photoillustration: Harold A. Perry; photos: Jupiter Images

Experiment NO.3 Series and parallel connection

Inductors in AC Circuits

Trigonometry for AC circuits

Unit: Charge Differentiated Task Light it Up!

Reading assignment: All students should read the Appendix about using oscilloscopes.

Series and Parallel Circuits

Section B: Electricity

Transcription:

Basic voltmeter use This worksheet and all related files are licensed under the Creative Commons ttribution License, version 1.0. To view a copy of this license, visit http://creativecommons.org/licenses/by/1.0/, or send a letter to Creative Commons, 559 Nathan bbott Way, Stanford, California 94305, US. The terms and conditions of this license allow for free copying, distribution, and/or modification of all licensed works by the general public. Resources and methods for learning about these subjects (list a few here, in preparation for your research): 1

Question 1 Questions What will this voltmeter register when connected to a battery as shown (assume a battery voltage of 6 volts)? Explain your answer. OFF + - file 00020 Question 2 What will this voltmeter register when connected to a battery as shown (assume a battery voltage of 6 volts)? Explain your answer. OFF + - file 00021 2

Question 3 If we were to connect a voltmeter directly to an ohmmeter, what would you expect to see the ohmmeter register, for resistance between its test leads???? - Ω + - Ω + file 01696 3

Question 4 Many electronic circuits use what is called a split or a dual power supply: Electronic circuit B 15 15 "Ground" Determine what a digital voltmeter would indicate if connected between the following points: Red lead on, black lead on ground Red lead on B, black lead on ground Red lead on, black lead on B Red lead on B, black lead on NOTE: in electronic systems, ground is often not associated with an actual earth-soil contact. It usually only refers to a common point of reference somewhere in the circuit used to take voltage measurements. This allows us to specify voltages at single points in the circuit, with the implication that ground is the other point for the voltmeter to connect to. file 00267 4

Question 5 Determine how much voltage a voltmeter would indicate when connected between the following points in this circuit: TB1 1 2 3 4 + - Battery (9 volts) Terminal block TB2 1 2 3 4 Terminal block Light bulb Between TB1-1 and TB1-3 Between TB1-4 and TB2-4 Between TB2-3 and TB2-1 Between TB1-1 and TB2-1 Hint: it might help to draw a neat schematic diagram of this circuit first, with all connection points labeled! file 00268 5

Question 6 Determine how much voltage a voltmeter would indicate when connected between the following points in this faulted circuit: TB1 1 2 3 4 + - Terminal block Battery (9 volts) Broken wire! TB2 1 2 3 4 Terminal block Light bulb (not lit) Between TB1-1 and TB1-3 Between TB1-4 and TB2-4 Between TB2-3 and TB2-1 Between TB1-1 and TB2-1 Hint: it might help to draw a neat schematic diagram of this circuit first, with all connection points labeled! file 00269 6

Question 7 Determine what these four voltmeters (, B, C, D) will register when connected to this circuit in the following positions (assume a battery voltage of 6 volts): B Ω switch closed C Ω Ω Ω D oltmeter = oltmeter B = oltmeter C = oltmeter D = file 00016 7

Question 8 Determine what these four voltmeters (, B, C, D) will register when connected to this circuit in the following positions (assume a battery voltage of 6 volts): B Ω switch open C Ω Ω Ω D oltmeter = oltmeter B = oltmeter C = oltmeter D = file 00015 8

Question 9 Shown here is a circuit constructed on a PCB (a Printed Circuit Board ), with copper traces serving as wires to connect the components together: OFF SW1 Printed circuit board - - C1 R1 - + Battery How would the multimeter be used to measure the voltage across the component labeled R1 when energized? Include these important points in your answer: The configuration of the multimeter (selector switch position, test lead jacks) The connections of the meter test leads to the circuit The state of the switch on the PCB (open or closed) file 00096 Question 10 Suppose I were about to measure an unknown voltage with a manual-range voltmeter. This particular voltmeter has several different voltage measurement ranges to choose from: 500 volts 250 volts 100 volts 50 volts 25 volts 10 volts 5 volts What range would be best to begin with, when first measuring this unknown voltage with the meter? Explain your answer. file 00270 9

Question 11 Suppose I needed to test for the presence of DC voltage between all wires connected to this terminal block. What is the fewest number of individual measurements I would have to perform with with a voltmeter in order to test for voltage between all possible wire pair combinations (remember that voltage is always measured between two points!)? TB25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Multi-conductor cable file 00271 10

Question 12 oltmeters must be connected in parallel with the voltage to be measured: Pictorial diagram Schematic diagram + - Ω In order to practically function, an voltmeter must have some finite amount of internal resistance. It is usually a very large amount, but less than infinite. It should be apparent to you that the presence of this resistance will have some effect on the circuit voltage, when compared to the amount of voltage in the circuit without any meter connected, due to the fact that real voltage sources tend to sag when subjected to additional loads: oltmeter R internal Explain why it is usually safe to ignore the internal resistance of an voltmeter, though, when it is in a circuit. common term used in electrical engineering to describe this intentional oversight is swamping. In this particular circuit an engineer would say, The resistance of the light bulb swamps the internal resistance of the voltmeter. file 03639 11

nswer 1 nswers I could simply give you the answer, but this problem is so easy to simulate in real life that I d rather let you try it yourself! Follow-up question: what does this tell you about the nature of voltage, and how it is measured? nswer 2 The voltmeter will register -6 volts. What do you suppose will happen if the voltmeter is of the analog style (with a moving needle rather than a numerical display)? nswer 3 The ohmmeter should register a very high resistance. nswer 4 Red lead on, black lead on ground (Digital voltmeter reads +15 volts) Red lead on B, black lead on ground (Digital voltmeter reads -15 volts) Red lead on, black lead on B (Digital voltmeter reads +30 volts) Red lead on B, black lead on (Digital voltmeter reads -30 volts) nswer 5 Between TB1-1 and TB1-3 (oltmeter measures 9 volts) Between TB1-4 and TB2-4 (oltmeter measures 0 volts) Between TB2-3 and TB2-1 (oltmeter measures 0 volts) Between TB1-1 and TB2-1 (oltmeter measures 9 volts) nswer 6 Between TB1-1 and TB1-3 (oltmeter measures 9 volts) Between TB1-4 and TB2-4 (oltmeter measures 9 volts) Between TB2-3 and TB2-1 (oltmeter measures 0 volts) Between TB1-1 and TB2-1 (oltmeter measures 9 volts) nswer 7 oltmeter = 6 volts oltmeter B = 0 volts oltmeter C = 6 volts oltmeter D = 0 volts nswer 8 oltmeter = 0 volts oltmeter B = 6 volts oltmeter C = 6 volts oltmeter D = 0 volts 12

nswer 9 OFF Switch ON SW1 - - C1 R1 - + Battery The test lead connections (to the circuit) shown are not the only correct answer. It is possible to touch the test leads to different points on the PCB and still measure the voltage across the resistor (component labeled R1). What are some alternative points on the PCB where the voltage across R1 could be measured? nswer 10 Begin by setting the voltmeter to its highest range: 500 volts. Then, see if the movement needle registers anything with the meter leads connected to the circuit. Decide to change the meter s range based on this first indication. nswer 11 105 voltage measurements are necessary (minimum) to test for voltage between every possible combination of two wires out of 15 wires. Mathematically, the number of two-wire test combinations is specified by the equation: Where, n = The number of wires n (i 1) i=1 Challenge question: there is a way to mathematically reduce the expression shown above so that it only contains the variable n, and not i or the summation symbol ( ). nswer 12 When one quantity swamps another, we mean that its effect is huge compared to the effect of the other, so much so that we may safely ignore it in our calculations and still arrive at a reasonably accurate result. 13

Notes 1 Notes This question affords an excellent opportunity to discuss another foundational concept of electricity: that voltage is always measured between two points. Notes 2 sk the students how an analog (moving pointer) style of voltmeter would respond in this situation. This question lends itself very well to simple experimentation in the classroom, even during discussion time. Notes 3 sk your students why a voltmeter should have a very high resistance (many thousands or millions of ohms) between its test leads. How does this property of all voltmeters relate to how they are used to measured current in real circuits? Notes 4 This question may be easily answered with only a voltmeter, two batteries, and a single jumper wire to connect the two batteries in series. It does not matter if the batteries are 15 volts each! The fundamental principle may still be investigated with batteries of any voltage, so this is a very easy demonstration to set up during discussion time. Notes 5 This question provides an opportunity to discuss the concept of electrically common points: namely, that there can be no substantial voltage built up between points that are made electrically common by means of low-resistance connections between them. This is also an opportunity to develop the skill of drawing a schematic diagram for a real-life circuit. Schematic diagrams, of course, are very helpful in that they provide a nice, neat layout of all circuit components, making visualization of voltage drops and other quantities easier. Notes 6 sk your students this question: how does the break in the wire affect electrical commonality between TB1-4 and TB2-4? Notes 7 Students often find the terms open and closed to be confusing with reference to electrical switches, because they sound opposite to the function of a door (i.e. you can only go through an open door, but electricity can only go through a closed switch!). The words actually make sense, though, if you look at the schematic symbol for an electrical switch as a door mounted sideways in the circuit. t least visually, then, open and closed will have common references. One analogy to use for the switch s function that makes sense with the schematic is a drawbridge: when the bridge is down (closed), cars may cross; when the bridge is up (open), cars cannot. I have found that the concept of electrically common points is most helpful when students first learn to relate voltage drop with continuity (breaks or non-breaks) in a circuit. To be able to immediately relate the expected voltage drop between two points with the electrical continuity between those points is a very important foundational skill in electrical troubleshooting. Without mastery of this skill, students will have great difficulty detecting and correcting faults in circuits caused by poor connections and broken wires, which constitute a fair portion of realistic circuit failures. 14

Notes 8 Students often find the terms open and closed to be confusing with reference to electrical switches, because they sound opposite to the function of a door (i.e. you can only go through an open door, but electricity can only go through a closed switch!). The words actually make sense, though, if you look at the schematic symbol for an electrical switch as a door mounted sideways in the circuit. t least visually, then, open and closed will have common references. One analogy to use for the switch s function that makes sense with the schematic is a drawbridge: when the bridge is down (closed), cars may cross; when the bridge is up (open), cars cannot. I have found that the concept of electrically common points is most helpful when students first learn to relate voltage drop with continuity (breaks or non-breaks) in a circuit. To be able to immediately relate the expected voltage drop between two points with the electrical continuity between those points is a very important foundational skill in electrical troubleshooting. Without mastery of this skill, students will have great difficulty detecting and correcting faults in circuits caused by poor connections and broken wires, which constitute a fair portion of realistic circuit failures. Notes 9 Many multimeters use international symbols to label DC and C selector switch positions. It is important for students to understand what these symbols mean. The test lead connections (to the circuit) shown are not the only correct answer. It is possible to touch the test leads to different points on the PCB and still measure the voltage across the resistor (R1). However, if there are poor connections on the circuit board (between component leads and copper traces), measuring voltage at points on the circuit board other than directly across the component in question may give misleading measurements. Discuss this with your students. Notes 10 I always like to have my students begin their test equipment familiarity by using old-fashioned analog multimeters. Only after they have learned to be proficient with an inexpensive meter do I allow them to use anything better (digital, auto-ranging) in their work. This forces students to appreciate what a fancy meter does for them, as well as teach them basic principles of instrument ranging and measurement precision. Notes 11 This is an interesting mathematical exercise, to determine the total number of 2-wire combinations resulting from 15 wires. If your students have difficulty determining this number, suggest they try to figure out the total number of 2-wire combinations with a smaller quantity of wires, say four instead of fifteen. Incidentally, this is a powerful problem-solving technique: simplify the problem into one with smaller quantities, until the solution becomes intuitively obvious, then determine the precise steps needed to arrive at that obvious solution. fter that, apply those same steps to the original problem. The challenge question is actually pre-calculus or calculus level. Notes 12 I have found that the concept of swamping is extremely useful when making estimations. To be able to ignore the values of some components allows one to simplify a great many circuits, enabling easier calculations to be performed. 15