motorola Bluetooth Handsfree Headset BEFORE YOU BEGIN Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions. Take a moment before you get started to familiarize yourself with your new H700 Headset. Multi-Color Boom Volume Buttons Microphone H700 Get connected in quick steps. Speaker (on reverse side) Call Button CHARGE YOUR HEADSET Charge your headset's battery for hours: ENSURE YOUR HEADSET IS IN PAIRING MODE Before you can use your headset, you must pair (link) it with your phone. Open the headset boom to initiate easy pairing. After a few moments, the indicator light will be steadily lit in purple to indicate headset is in pairing mode. Plug the Motorola charger into the end of the headset. The indicator light turns red when the battery is charging. It may take up to minute for the indicator light to turn on. When the headset's battery is fully charged (about hours), the indicator light turns green. Disconnect the charger. Note: Headset is not functional while charging. (steadily purple for pairing mode) If the headset does not enter pairing mode, see TROUBLESHOOTING for help.
TROUBLESHOOTING My headset will not enter pairing mode. Make sure that any devices previously paired with the headset are turned off. If the indicator light is flashing in blue, turn off the other device, then close and reopen the headset boom. The indicator light becomes steadily lit in purple indicating the headset is now in pairing mode. My phone doesn't find my headset. Make sure the indicator light on your headset is on (lit in purple) and steady when your phone is searching for devices (see step ). My headset worked before but now it's not working. Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step ). If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature and pair your phone and headset again (see steps and ). Support. If you need more help, contact us at -877-MOTOBLU or visit us at www.hellomoto.com//bluetoothsupport Motorola, Inc. Consumer Advocacy Office 07 East Algonquin Road Schaumburg, IL 6096 www.hellomoto.com -877-MOTOBLU -888-90-656 (TTY/TDD United States for hearing impaired) Guide Number: 680999A88-B MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners. Motorola, Inc. 006. TURN ON BLUETOOTH ON YOUR PHONE AND PAIR WITH HEADSET Your phone's Bluetooth feature is off by default. To use your headset, turn on the Bluetooth feature in your phone. To turn on Bluetooth: Select M (Menu) > Settings > Connection > Bluetooth Link > Setup. 5 6 Scroll to Power. Press Change. Select On. Select Back. Select Handsfree. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. 7 8 9 0 TURN ON BLUETOOTH ON YOUR PHONE AND PAIR WITH HEADSET Continued Select [Look for Devices]. Note: Do not select STOP--you will automatically be taken to the next screen. Select Motorola H700. Select Yes to bond. Enter the passkey 0000 and select OK. When your headset and phone are successfully paired, the indicator light changes from steadily lit to flashing blue. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.
TEST AND USE Your phone and headset are now paired and ready to make and receive calls. To confirm they are operating properly, make a call: Place the headset over your ear. See "Wearing the Headset" on the reverse side of this guide. USING YOUR H700 See Features and Functions Guide on the reverse side for information on using your H700 On your phone, dial the number you want to call and press the Send key. If your phone and headset are successfully paired, you will hear ringing on the headset. After you have successfully paired your phone and headset, you don't need to repeat these steps. For daily use, ensure that your headset is turned ON and that your phone's Bluetooth feature is ON. To save battery power, turn OFF the headset when you don't use it for an extended time by closing the boom. Features and Functions Guide H700 Bluetooth Handsfree Headset TURNING HEADSET ON AND OFF To turn your headset on, open the headset boom. The indicator light flashes blue. To turn your headset off, close the headset boom. The indicator light will turn off. IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your H700. Multi-Color
WEARING THE HEADSET Open the headset boom, then open the earhook. Loop the earhook over your ear. Press the headset to your ear. Point the headset boom towards your mouth. CHANGING FOR USE ON OTHER EAR You can wear your H700 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear: Open the headset boom, then open the earhook (90 from the headset). Gently lift and pull the top of the earhook up and off the upper hinge pin. Then, pull it away to remove it. Flip the headset over. Hook the bottom of the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin. Open Earhook Pull Earhook Up Hinge Pin CHANGING VOLUME BUTTON ORIENTATION You can also change the orientation of the volume buttons on your headset. Turn the headset power off. Press the Call button until the indicator light becomes steadily lit in purple, then press the Volume button you want to assign as the "volume up" button. European Union Directives Conformance Statement Hereby, Motorola declares that this product is in compliance with: The essential requirements and other relevant provisions of Directive 999/5/EC. All other relevant EU Directives. Product Approval Number Volume Buttons Call Button The above gives an example of a typical Product Approval Number. You can view your product s Declaration of Conformity (DoC) to Directive 999/5/EC (to R&TTE Directive) at www.motorola.com/rtte. To find your DoC, enter the product Approval Number from your product s label in the Search bar on the web site.
Function Make a voice dial call End a call Answer a call Ignore a call Redial last call MAKING CALLS Action Tap the Call button and speak the name after the tone Tap the Call button Open headset boom or tap the Call button (if boom is already open) Note: Your H700 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information. MAKING CALLS CONTINUED Function Answer a second incoming call Toggle between two active calls Join a -way call Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Disable the indicator light Mute or unmute a call Action Call button (places first call on hold) the Call button both Volume buttons Open headset boom both Volume buttons for to seconds Tap both Volume buttons Note: Some features are phone/network dependent. INDICATOR LIGHTS With the Charger Plugged In Red (steady) Yellow (steady) Green (steady) Headset Status Charging (less than 80% charged) Charging (more than 80% charged) Charging complete With No Charger Plugged In Headset Status Off Power off Purple (steady) Pairing mode/ Volume button orientation Red Battery low Blue (0 rapid flashes) Pairing successful Blue (slow pulse) Connected (on a call) Blue (quick flash) Standby (not on a call) Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode. AUDIO TONES The audio tones provide information about your headset status. Audio Tone Single high tone when pressing Volume button Five rapid high tones repeated every 60 sec. No audio indications; deteriorating quality Ring tone Single high tone Single low tone Dual high/low tone Single high tone Low to high tone Two ascending tones Two descending tones Headset Status Volume at minimum or maximum Low battery Out of range Incoming call Pairing confirmation Voice activation Voice tag not recognized End call Phone network not available Mute enabled Mute disabled