Page 1 of 6 General Specifications - Mounting Part Number 2450AT43A100 Frequency Range 2400-2500 Mhz Peak Gain 2.0 dbi typ. (-V) Average Gain 0.5 dbi typ. (-V) 9.5 db min. Input Power Impedance Operating Temperature Reel Quanity 2W max. 50 Ω -40 to +85 C 1,000 Part Number Explanation P/N Suffix Packing Style Termination style Bulk T & R Suffix = S Suffix = E 100% Tin Suffix = None Tin / Lead Please Consult Factory eg. 2450AT43A100S eg. 2450AT43A100E eg. 2450AT43A100 (E or S) Mechanical Dimensions In mm L 0.276 ± 0.008 7.00 ± 0.20 W 0.079 ± 0.008 2.00 ± 0.20 T 0.047 +.004/-.008 1.20 + 0.1/-0.2 a 0.020 ± 0.012 0.50 ± 0.30 a W T Terminal Configuration No. Function 1 Signal Feed Terminal 2 NC (To be used as Anchoring to PCB) 2 1 L Mounting Considerations - Mounting Mount these devices with brown mark facing up. Units: mm * Line width should be designed to provide 50 Ω impedance matching characteristics. 1.0 8.0 GND Plane 5.5 * 0 2.0 GND Plane Note: Matching components may be needed when designing into a PCB so, make sure to leave a shunt-seriesshunt or "pi" network available space/footprint when laying out. More info: http://johansontechnology.com/tuning 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FA 805.389.1821
) ) Page 2 of 6 Test Board of Mounting style, p/n: 2450AT43A100-EB1SMA 40mm 9.5m 40mm 50Ω Feed Line 20mm 0Ω Antenna Ground 19mm No Ground * This 50ohm trace to the antenna can be shorten (considerably) to suit your PCB space constraints 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FA 805.389.1821
Page 3 or 6 Typical Radiation Patterns on Test Board of Mounting p/n: 2450AT43A100-EB1SMA -V/-H cut @2.45GHz -cut scanning direction -V/-H cut @2.45GHz -cut scanning direction -V/-H cut @2.45GHz -cut scanning direction 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FA 805.389.1821
Page 4 of 6 General Specifications - Mounting Part Number 2450AT43A100 Input Power 2W max. Frequency Range 2400-2500 Mhz Impedance 50 Ω Peak Gain 2.0 dbi typ. (-V) Operating Temperature -40 to +85 C Average Gain 1.0 dbi typ. (-V) Reel Quanity 1,000 9.5 db min. Mounting Considerations - Mounting Mount these devices with brown mark facing up. Units: mm * Line width should be designed to provide 50 Ω impedance matching characteristics. 1.0 8.0 GND 6.8 5.5 0 Ohm 2.0 * GND Note: Matching components might be needed when design into a PCB so, make sure to leave a shunt-seriesshunt or "pi" network available space/footprint when laying out. More info: http://johansontechnology.com/tuning 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FA 805.389.1821
Page 5 of 6 Test Board of Mounting style, p/n: 2450AT43A100-EB2SMA Ground 20mm 40mm Matching Circuit 50Ω Feed Trace (CPWG) 9mm 40mm 5mm 9.5mm 2.5mm No Ground * This 50ohm trace to the antenna can be shorten (considerably) to suit your PCB space constraints 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FA 805.389.1821
Page 6 or 6 Typical Radiation Patterns on Test Board of Mounting p/n: 2450AT43A100-EB2SMA -V/-H cut @2.45GHz -cut scanning direction -V/-H cut @2.45GHz -cut scanning direction -V/-H cut @2.45GHz -cut scanning direction 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FA 805.389.1821