Mark 0 for ar Fluorescent and 4-pin CFL for T8 ar and 40W Long Twin Tube for T5/HO Programmed Start Electronic Fluorescent Dimming s for 4-Pin Compact Fluorescent P R O D U C T O V E R V I E W : Mark 0 ballasts for linear fluorescent, 4-pin CFL, and T5HO lamps are the ideal choice for -wire dimmable lighting installations. Without the need of additional control leads, the Mark 0 makes controllable fluorescent lighting systems as fast and as easy to install as fixed output systems - while being up to 80% more energy efficient than incandescent systems. The Mark 0 ballasts programmed start design optimizes lamp and dimming performance by monitoring system performance and making continuous adjustments. Plus the Mark 0 does not have to ramp up to full light output and then dim. The ballast will start lamps at the minimum dimming level, increasing comfort levels for area occupants. DESIGN HIGHLIGHTS: 00% - 5% full range continuous dimming (T5HO to %) Increase flexibility and enhances visual comfort Energy efficient Provides up to 65% energy savings over standard fixed output T8 ballasts (e.g., REL-P3-SC) Absence of additional control leads Enhances ease of installation - requires no extra wiring Highly flexible and compatible with a wide variety of controls by a broad range of control manufacturers Programmed Start operation Optimizes lamp life in frequent starting conditions ignition at any light setting, including the 5% dim level (% in T5HO) Eliminates the need to ramp up to 00% light output when starting Operates above 4 khz Minimizes risk of interference with infrared remote control systems and provides continuous flicker-free dimming End-of- (EOLL) life protection circuit (CFL and T5/HO models only) Safely removes power from lamp at end of life APPLICATIONS: General Lighting Board Rooms Executive Offices Conference Rooms Meeting Rooms Auditoriums Tel: 800-3-086 Fax: 888-43-88 Customer Support/Technical Service: 800-37-333 www.advancetransformer.com
Mark 0 F7T8, FBO6T8 (7W) Mark 0 3 F5T8, FBO4T8 (5W) Mark 0 3 F3T8, FBO3T8, F3T8/U6 (3W) Mark 0 3 HIGH FREQUENCY ELECTRONIC BALLASTS 30/7 55/3 79/9 For 7-3W T8 REZ-3-SC 0.0 4/7 VEZ-3-SC 0.09 5 REZ-S3-SC 0.3 38/3.05/0.05 0 VEZ-S3-SC 0.4 50/0 B 53 REZ-3S3-SC 0.47 56/8 VEZ-3S3-SC 0. 55 REZ-3-SC VEZ-3-SC REZ-S3-SC VEZ-S3-SC REZ-3S3-SC VEZ-3S3-SC THD % Current ( F/ C).05/0.05 0 0.6 0. 0.46 0.0 0.66 0.9 50/0 B REZ-3-SC 0.9 35/9 VEZ-3-SC 0.3 5 REZ-S3-SC 0.57 68/5.00/0.05 0 VEZ-S3-SC 0.5 50/0 B 53 REZ-3S3-SC 0.86 0/0 VEZ-3S3-SC 0.37 55 5 53 55 For ballast dimensions and wiring diagrams see page 5 F4T5/HO (4W) HIGH FREQUENCY ELECTRONIC BALLASTS For 4-55W T5/HO THD % Current ( F/ C) - IntelliVolt Mark 0 IEZ-S4-D 57/6.00/0.05 0 0.48-0. 50/0 D 53 F54T5/HO (54W) FCT5/HO (55W) Mark 0 Mark 0 REZ-54 VEZ-54 REZ-S54 VEZ-S54 REZ-54 VEZ-54 REZ-S54 VEZ-S54 63/3 5/4 59/3 4/4.00/0.03 0.90/0.03 0 0 0.53 0.3.05 0.45 0.50 0. 0.96 0.4 50/0 50/0 D D 5 53 5 53 For ballast dimensions and wiring diagrams see page 5
HIGH FREQUENCY ELECTRONIC BALLASTS For 8-70W T4 CFQ8W/G4q - 8W CFL Quad Tube (PL-C8W/4P, F8DBX/4P, CF8DD/E) CFTR8W/GX4q - 8W CFL Triple Tube (PL-T8W, F8TBX/4P, CF8DT/E) REZ-Q8-M-BS REZ-Q8-M-LD 0.8 /7 VEZ-Q8-M-BS Mark 0 VEZ-Q8-M-LD 0.07.00/0.05 0 REZ-Q8-M-BS REZ-Q8-M-LD 0.36 43/4 VEZ-Q8-M-BS VEZ-Q8-M-LD 0.6 CFQ6W/G4q - 6W CFL Quad Tube (PL-C6W/4P, F6DBX/4P, CF6DD/E) CFTR6W/GX4q - 6W CFL Triple Tube (PL-T6W, F6TBX/4P, CF6DT/E) Mark 0 REZ-T4-M-BS REZ-T4-M-LD REZ-T4-M-LD-K ❿ VEZ-T4-M-BS VEZ-T4-M-LD VEZ-T4-M-LD-K ❿ REZ-Q6-M-BS REZ-Q6-M-LD REZ-Q6-M-LD-K ❿ VEZ-Q6-M-BS VEZ-Q6-M-LD VEZ-Q6-M-LD-K ❿ CFTR3W/GX4q - 3W CFL Triple Tube (PL-T3W, F3TBX/4P, CF3DT/E) REZ-T4-M-BS REZ-T4-M-LD REZ-T4-M-LD-K ❿ 38/9 VEZ-T4-M-BS Mark 0 VEZ-T4-M-LD.00/0.05 0 VEZ-T4-M-LD-K ❿ REZ-T4-M3-BS REZ-T4-M3-LD 76/0 VEZ-T4-M3-BS VEZ-T4-M3-LD CFTR4W/GX4q - 4W CFL Triple Tube (PL-T4W, F4TBX/4P, CF4DT/E) REZ-T4-M-BS REZ-T4-M-LD REZ-T4-M-LD-K ❿ 49/0 VEZ-T4-M-BS Mark 0 VEZ-T4-M-LD.00/0.05 0 VEZ-T4-M-LD-K ❿ REZ-T4-M3-BS REZ-T4-M3-LD 98/0 VEZ-T4-M3-BS VEZ-T4-M3-LD CFTR57W/GX4q - 57W CFL Triple Tube (PL-T57W, F57QBX/4P, CF57DT/E) REZ-T4-M3-BS Mark 0 REZ-T4-M3-LD 66/8.00/0.05 0 VEZ-T4-M3-BS VEZ-T4-M3-LD CFTR70W/GX4q - 70W CFL Triple Tube (F70QBX/4P, CF70DT/E) REZ-T4-M3-BS Mark 0 REZ-T4-M3-LD 80/8.00/0.05 0 VEZ-T4-M3-BS VEZ-T4-M3-LD Note: ❿ Replacement/Retrofit Kits indicated by Bold Type with suffix -K are available to distributors. Refer to page-4 for details. 3/8 58/6.00/0.05 0 THD % Current 0.6 0. 0.48 0. 0.3 0.4 50/0 0.64 0.8 0.4 0.8 50/0 0.8 0.36 0.55 0.4 0.67 0.9 ( F/ C) 50/0 Size 50/0 Size Size Size 3 Size Size 3 34 3 34 3 34 3 34 3 50/0 Size 3 34 50/0 Size 3 34 Some lamp manufacturers recommend burning in new lamps 00 hours at full light output before dimming. Consult lamp manufacturer. s utilizing poke-in connectors can accept wire gauges from AWG 6-0. For ballast dimensions and wiring diagrams see page 5 Mark 0
Mark 0 HIGH FREQUENCY ELECTRONIC BALLASTS For 4-55W FT5 FT4W/G - 4/7WW Long Twin Tube (PL-L4W, F7BX/RS, FT4DL) THD % Current (F/C) - IntelliVolt Mark 0 IEZ-S4-D 57/6.00/0.05 0 0.48-0. 50/0 D 3 FT36W/G - 36/39W Long Twin Tube (PL-L36W, F39BX/RS, FT36DL) REZ-TTS40-SC 38/9 Mark 0 VEZ-TTS40-SC.00/0.05 0 REZ-TTS40-SC 75/6 VEZ-TTS40-SC FT40W/G/RS - 40W Long Twin Tube (PL-L40W, F40BX, FT40DL/RS) REZ-TTS40-SC 4/0 Mark 0 VEZ-TTS40-SC.00/0.05 0 REZ-TTS40-SC 80/7 VEZ-TTS40-SC FT55W/G - 55W Long Twin Tube (PL-L55W, F55BX, FT55DL) REZ-54 59/3 Mark 0 VEZ-54 0.90/0.05 0 REZ-S54 4/4 VEZ-S54 0.3 0.4 0.64 0.7 0.3 0.5 0.68 0.30 0.50 0. 0.96 0.4 50/0 B 50/0 B 50/0 D 34 3 34 3 34 3 Burn in new lamps 00 hours at full light before dimming. s utilizing poke-in connectors can accept wire gauge AWG 6-0. For ballast dimensions and wiring diagrams see page 5
- FT40W - Fig. 34 - T8 - Fig. 5 3- T8 - Fig. 55 - FT40W - Fig. 3 - T8 - Fig. 53 Fig. A.9" (3.8) 3.00" (76.4) Size *.9" (3.8) 3.00" (76.4).00" (50.8).5" 4.0" (06.7) 4.55" (6.6) 4.0" (06.7) 4.55" (6.6).375" 8.906" 9.5".9" 3.00" -LD Size 3* 3.00" -BS.9".00" 5.5" 6.0" 5.5" 6.0" -LD Dual Connectorfor for Only Only -BS Fig. B Fig. D* Fig. D ncludes connectors with no leads * Leads not included.8".70 " 8.9" 9.50" N O T E :. One and Two-lamp ballasts may be remote mounted up to six feet away from lamps. Three lamp ballasts may not be remote mounted.. 5 /8 and 6 U-bend lamps also acceptable. 3. must be mounted within ¾ of a ground plane. Mark 0
Mark 0 BALLAST SPECIFICATIONS Mark 0 Section I - Physical Characteristics. shall be physically interchangeable with standard electromagnetic or standard electronic ballasts, where applicable.. shall be available in a plastic/metal can or all metal can construction to meet all plenum requirements..3 shall be provided with poke-in wire trap connectors or integral leads color coded per C8.. Section II - Performance Requirements. shall be Programmed Start.. shall contain auto restart circuitry in order to restart lamps without resetting power..3 shall operate from 60 Hz input source of V, V or 347V as applicable with sustained variations of +/- 0% (voltage and frequency) with no damage to the ballast..4 shall be high frequency electronic type and operate lamps at a frequency above 4 khz to avoid interference with infrared devices and eliminate visible flicker..5 shall have a greater than 0.98 at full light output and greater than 0.90 throughout the dimming range for primary lamp..6 shall have a minimum ballast factor of.00 at maximum light output and 0.05 at minimum light output for primary lamp..7 shall provide for a Current Crest of.7 or less throughout the dimming range in accordance with lamp manufacturer recommendations..8 input current shall have Total Harmonic Distortion (THD) of less than 0% at maximum light output when operated at nominal line voltage with primary lamp. Total Harmonic Current (THC) at minimum light output shall not exceed THC at maximum light output..9 shall have a Class A sound rating..0 shall have a minimum starting temperature of 0C (50F) for primary lamp.. shall provide EOL Protection Circuit for all T5, T5/HO, and CFL lamps.. shall control lamp light output from 00% - 5% relative light output for T8 and CFL lamps and 00% - % relative light output for T5/HO lamps..3 shall ignite the lamps at any light output setting without first going to another output setting..4 shall tolerate sustained open circuit and short circuit output conditions without damage. Section III - Regulatory Requirements 3. shall not contain any Polychlorinated Biphenyl (PCB). 3. shall be Underwriters Laboratories (UL) listed, Class P and Type Outdoor; and Canadian Standards Association (CSA) certified where applicable. 3.3 shall comply with C6.4 Category A for Transient protection. 3.4 shall comply with C8. where applicable. 3.5 shall comply with the requirements of the Federal Communications Commission (FCC) rules and regulations, Title 47 CFR part 8, Non-Consumer (Class A) for EMI/RFI (conducted and radiated). Section IV - Other 4. shall be manufactured in a factory certified to ISO 900 Quality System Standards. 4. shall carry a warranty from date of manufacture against defects in material or workmanship for operation at a maximum case temperature of (Go to our web site for up-to-date warranty information: www.advancetransformer.com/warranty). 4.3 Manufacturer shall have a fifteen year history of producing electronic ballasts for the North American market. 4.4 shall be controlled by a compatible Mark 0 two-wire dimmer. 4.5 shall be Advance part # or approved equal. Advance 075 W. Higgins Road Rosemont, IL 6008 Tel: 800-3-086 Fax: 888-43-88 Customer Support/Technical Service: 800-37-333 OEM Support: 866-95-5886 www.advancetransformer.com 008 Advance, A Division of Philips Electronics North America All rights reserved. Reproduction in whole or part is prohibited without the prior written consent of the copyright owner. The information presented in this document, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequences of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Form No. EL-00-R03 3/08