superabrasive RSSING Tools www.abrasive-tech.com
RSSING TOOLS Introduction - iamonds & ressing Tools Natural diamonds are available in many shapes: octa hedrons, dodecahedrons, flats, elongated shapes, triangles, irregular shapes and grits. iamond qualities vary from the finest pure crystals, free from flaws, cracks or impurities, to the lowest grade crystals which can be considerably flawed. brasive Technology s team of associates have the experience to help you choose the best diamond types and quality to match your tooling needs. We also have highly qualified design engineers to custom design a tool to fit your exacting requirements. iamond Grades asic ressing pplications PPLITION ROMMN PPLITION TOOL TYP For hard wheels or when very fine finishes and close tolerances are required, such as thread, bearing and gear grinding For demanding requirements and close tolerance work quality 4 resettable points quality 3 resettable points ressing straight grinding wheels Simple profiles, thread and gear grinding Straight and profile dressing Large O wheels, surface and centerless wheels ngle, radius and profile dressing Single-Point ressing Tool Profile/lade ressers Multi-Point/Impregnated ressers hisel & one Profile Tools (Plain & iaform Style) For average grinding conditions quality 2 resettable points ustom designed to meet grinding profile requirements P Form ressers For general purpose work, still resettable quality 1 resettable point For general purpose work, non-resettable NR Non-Resettable 1
RSSING TOOLS Recoendations for Single-Point ressers 1. Mounting the dressing tool Mount the tool with minimum overhang to avoid vibration. Never mount a dressing tool in an oversized hole. Mount the diamond with a 10 to 15 degree drag angle pointing in the direction of wheel travel. When a straight dressing fixture is mounted on the table, position the diamond point past the center. diamond pointing to the center of the wheel will cause vibration and shorten the tool life. (Figure 1) 2. oolant ress dry when grinding dry. ress with coolant if it is used during the grinding cycle. o not turn the coolant on if the dressing cycle was started dry. The thermal shock may fracture the diamond. irect a generous flow of coolant to the diamond at all times. 4. Trueing time cycle To calculate the trueing cycle, determine: The grit size of the grinding wheel. The speed of the grinding wheel. The width of the grinding wheel. To dress an open structure and aggressive grinding wheel, the diamond should not hit each abrasive grain more than once per revolution. Therefore, grit size and wheel speed will determine traverse rate. To achieve a better finish, slow down the traverse rate to hit each grain a maximum of 2 times per revolution. If the traverse rate is too slow the diamond dulls the abrasive and the grinding wheel will burnish and cause heat checks. Figure 1 Figure 2 Figure 3 RIGHT orrect PROPRLY US Properly used 10º - 15º WRONG Incorrect IMPROPRLY US Improperly used 3. Operating parameters Start the dressing cycle in the center of the wheel. (Figure 2) Traverse rate: See chart below. Infeed: 36-60 grit whl.001 (.025) to max.002 (.05) 80-180 grit whl.0005 (.013) to max.001 (.025) 220 grit and finer.0002 (.005) to max.0005 (.013) Index the diamond dresser frequently When the diamond wears, the increased contact area will generate more heat and shorten the tool life. Index the dresser 20 to 30 degrees when the wear flat reaches 1/16 (1.6). The diamond will then develop a conical wear pattern. (Figure 3) Reset the diamond before a 3/32 (2.4) flat develops FOR SG WHLS: Reduce infeed rate by 50% and increase the traverse rate. Use good quality diamonds with a sharp point. 1) General purpose dressing applications iamond size = iameter of wheel () + Width (W) 10 2) Severe dressing applications iamond size = iameter of wheel () + Width (W) 7 Instructions 1. heck the spindle speed. 2. Go to the corresponding grit size column. 3. Multiply the indicated seconds by the width of the wheel. 4. The lower figure applies to dress an open wheel. 5. The higher figure results in a finer finish. hart Of Trueing Time In Seconds Per * (Lower figures for open wheel Higher figures for finish) Grit size Rev/Min. 36 46 60 80 100 120 150 180 220 500 6-10 8-15 12-20 18-30 24-40 30-50 35-56 40-60 50-80 750 4-7 6-10 8-13 12-20 16-26 20-33 27-42 30-45 38-60 1,000 3-5 4-8 6-10 9-15 12-20 15-25 18-28 20-30 25-40 1,250 2-4 3-6 5-8 7-12 10-16 12-20 14-22 16-24 20-32 1,500 2-3 3-5 4-7 6-10 8-14 10-17 12-19 13-20 17-27 1,750 1.5-3 2.5-4 3.5-6 5-9 7-12 9-14 10-16 11-17 14-23 2,000 1.3-2 2-4 3-5 4-8 6-10 8-12 9-14 10-16 11-17 2,500 1-2 1.5-3 2.5-4 3.5-6 5-8 6-10 7-11 8-12 10-16 2,750 1-2 1.4-2.8 2-3.5 3-5.5 4-7 5.5-9 6-10 7-11 9-15 3,200.9-1.7 1.3-2.6 1.7-3 2.6-5 3-6 4.5-8 5-9 6-10 8-13 3,600.8-1.5 1-2 1.5-2.5 2.3-4 2.5-5 4-7 4.5-8 5-8.5 7-12 *To convert trueing time into seconds per centimeter, divide table value by 2.54. XMPL. For a 36 x 4 (91.44cm x 10.16cm) 46 grit wheel running at 500 RPM, the dressing time will be 8 seconds x 4 = 32 seconds to dress an open wheel, 15 x 4 = 60 seconds to dress for finer finish. These calculations assume that a relatively sharp diamond is used. 2
RSSING TOOLS Single-Point Shank esigns Straight Shank Taper Headed Shank ouble nded Hand resser Magazine resser (Non-Resettable) xtraction Hole Plain Headed Shank Turnable Head resser ranked Head Hexagon Headed Shank Location Flat Screw river Slot Taper Shank Recess for Location Tapered Head for oolant Plain Headed Taper Shank Recess for Point Location oolant Slots Hexagon Headed Taper Shank Partially Threaded Threaded Shank Totally Threaded hisel Shank Internal Thread ll the above shank designs are available in Resettable and Non-Resettable formats. 3
RSSING TOOLS Single-Point Resettable & Non-Resettable Single-Point ressers Recoended Non-Resettable pplications Toolroom grinders O.. and surface grinding wheels up to 18 x 3 (4500 x 750) urr grinding wheels enterless regulating wheels General purpose work Recoended Resettable pplications Very hard wheels SG wheels Thread or gear grinders Profile grinders To dress small internal grinding wheels HOW TO ORR Tool specs: 1. esign/description of tool shank 4. Size of diamond 2. Shank size 5. imensions of wheel to 3. Quality of diamond be dressed iameters of 1/4 (6.3) to 3/4 (19), up to 6 (150) long. Precision ressing Tools For Thread Grinders ressing tools for thread grinders require very sharp crystals. They are center set to.003 (.076) T.I.R. For Internal Grinders Heald Style To ress oncave Radii 40 ο FLTS imensions 3/8 9.5 3 76.20 1/4 6.35 Natural diamonds center set to.003 (.076) T.I.R. JONS & LMSON Style imensions 1/4 6.35 1 25.40 1/4 6.35 2 50.80 iamond is center set to.002 (.051) T.I.R. ryant Style imensions 1/4 6.35 11/16 17.46 3/8 9.52 7/16 11.10 1 25.40 To ress Radius.010.254.032.813.015.381.062 1.574.020.508.125 3.174.025.635 imensions 1/16 1.59 1/2 12.70 1/8 3.17 1/4 6.35 1 25.40 3/8 9.52 1/4 6.35 1 3/16 30.15 3/8 9.52 7/16 11.10 1 3/32 27.79 7/16 11.10 1 1/8 28.57 7/16 11.10 1 5/8 41.27 odecahedron diamonds are center set to within.004 (.1) T.I.R. 4
RSSING TOOLS Single-Point Rotadress ressing Tool onventional Grit Wheel 1 3 5 This specialized dressing tool features indexable action promoting sharp diamond exposure to achieve optimum conditions on grinding wheels, resulting in ideal surface finish and material removal rates. Improved throughput and reduced cost 6 4 2 esigned for ease of use - Operators turn the dresser quickly with a spanner. asy access to even the most confined areas of grinding machines. No re-referencing of dressing position is required after indexing. 5
RSSRS Profile/lade lade ressers are available in fixed and swivel formats Precision Profile tools are a cost effective alternative to expensive shaped single-point diamond tools. chieve close tolerance profile and finish. vailable in high quality graded natural diamond grits or hand set needle shaped diamonds. Standard Replacement lade ressers* Types Side Set lades enter Set lades F imensions of the diamond plate P2 X = 10 (.379 ) P4 X = 15 (.590 ) x 30º 20º 30º x fliese fa/h 13/16 20.5 25/32 20 1/4 6.1 3/16 5 9/32 7 29/32 23 25/32 20 1/4 6.1 3/16 5 9/32 7 Fixed lade ressers Range: imensions: pplication: Please state when ordering: Small carat weight (0.4-2 carat). etween 10 (.379 ) and 20 (.787 ) width. High wear applications. ressing large wheels. Shank dimensions. Wheel type. Wheel size (diameter and width). Grit size and type. F imensions of the diamond plate P1 X = 10 (.379 ) P3 X = 15 (.590 ) 30º x 13/32 10.5 13/32 10 1/4 6.1 20º 3/16 5 9/32 7 30º x 1/2 13 13/32 10 1/4 6.1 3/16 5 9/32 7 º (0-45) º *Shown above are standard sizes. ontact customer service for full range. This product is also available in synthetic diamond. L W.394 -.787 (10-20) R R ll purpose forming tool suitable for all but very fine forms. These blades contain 2 or 3 layers of selected long diamonds. 6
RSSRS Impregnated Impregnated ressers For Wheels 20 X 6 and Smaller (500 x 150) For Wheels 20 X 6 and Larger (500 x 150) Small diamonds are carefully screened and are randomly spaced in an abrasion resistant matrix. Why they save money: 15º 15 ο 15º 15º iamonds can be completely consumed, nothing is wasted. Longer tool life. Tool wear is shared by many small diamonds. Less downtime because of shorter dressing cycle. Fewer dressing passes saves wheel wear. Recoendations: Traverse rate: 25 IPM (.06M/min..) and faster. Infeed:.002 (.05). Start the dress in the center of the wheel. Use flood coolant. 1/2 12.7 3/8 9.52 7/16 11.11 3/4 19.05 1/4 6.35 1/2 12.7 3/8 9.52 7/16 11.11 3/4 19.05 1/4 6.35 1/2 12.7 3/8 9.52 7/16 11.11 3/4 19.05 1/4 6.35 3/4 19.05 3/8 9.52 7/16 11.11 15/16 23.81 1/4 6.35 3/4 19.05 5/16 8.26 7/16 11.11 15/16 23.81 1/4 6.35 3/4 19.05 5/16 8.26 7/16 11.11 15/16 23.81 1/4 6.35 1-6--7 2-4--7 2-4--7 (54 to 100 grit) (46 grit & coarser) (46 grit & coarser) 1-8--7 2-6--7 2-6--7 (120 grit & finer) (54 grit & finer) (54 to 100 grit) 2-8--7 (120 grit & finer) 2-4--7 1-4--7 1-4--7 (46 grit & coarser) (46 grit & coarser) (46 grit & coarser) 2-6--7 1-6--7 1-6--7 (54 to 100 grit) (54 to 100 grit) (54 to 100 grit) 2-8-7 1-8--7 1-8--7 (120 grit & finer) (120 grit & finer) (120 grit & finer) For Wheels 12 and Larger (300) 2R-6-K-7 3/8 9.52 3/8 9.52 7/16 11.11 2 1/2 63.5 For Wheels 10 and Smaller (250) 1R-6-J-7 1/4 6.35 1/4 6.35 7/16 11.11 2 50.8 rown resser Recoendations: Traverse rate: 30 IPM (.76M/min..) and faster. Infeed:.001 to.002 (.025 to.05). Use flood coolant. These are starting feeds and speeds and may need adjustment to suit the part specifications. The tool re quires periodic indexing. Specifications: rown - 1 x 5/8 x 1/8 (25.4 x 15.9 x 3.2) Shank - 7/16 x 1 5/8 OL (11.1 x 41.3) 7
RSSRS Multi-Point Indexable isc Type resser Small elongated whole diamonds are carefully selected for quality and uniformity of shape. imensions Shank Style imensions Recoended Use Shank Style imensions Recoended Use 1 1/2 12.70 5/32 3.81 Small surface grinders maximum 10 (250) wheels 1 5/8 15.87 5/32 3.81 Small surface grinders maximum 10 (250) wheels 1 1/2 12.70 5/32 3.81 O.., centerless, surface grinders maximum 20 (500) wheels 1 5/8 15.87 5/32 3.81 O.., centerless, surface grinders maximum 20 (500) wheels 3 11/16 17.46 3/16 4.75 O.., centerless, surface grinders over 20 (500) wheels 3 7/8 22.22 3/16 4.75 O.., centerless, surface grinders over 20 (500) wheels luster Type resser esigned for straight pass grinding, these tools are of a robust construction and available in diameters from 1/4 (6.35) to 3/4 (19.05) as standard. Finest natural diamond grits are used for rapid stock removal and fine finish applications. Single-Layer ressing lock esigned to dress straight wheels on tool room surface grinders. Quickly removes all previous forms or shapes. Off-Hand resser For hand trueing and dressing of abrasive grinding wheels. 8
PROFIL TOOLS hisel & one Profile Tools one Lapped ressing Tool Fine quality elongated diamonds are used in our cone shaped dressing tools. They are lapped to.003 (.076) T.I.R. Polished hisel ressing Tool The finest quality flat elongated diamonds are used in our chisel edge dressing tools. They are lapped to.005 (.127) chisel width within.003 (.076) of center. L Specify angle, diameter, L length, R radius L Specify angle, diameter, L length, R radius R R 60 ο 75 ο 90 ο 40 ο 60 ο 75 ο Radius Radius.005.127.010.253.015.381.020.508.005.127.010.253.015.381.020.508 iaform Style iaform and Pantocrush style dressers are made with the finest quality triangular shaped diamonds. The grain is oriented to expose the hardest direction of the diamond to the abrasive forces of the grinding wheel. This yields longer tool life. Polycrystalline diamond (P) tool blanks can be used on very selective applications. L R 110 ο Specify angle, diameter, L length, R radius Phono Points L 60 ο 75 ο 90 ο imensions.125 3.2 L 1 25.4 For dressing small radii fine grit wheels 9
FORM RSSRS Polycrystalline iamond (P) SI F P P Form ressers cost effective alternative to roll dressing and iaform style dressing. an impart complex and highly accurate forms to grinding wheels. Long lasting. Less machine downtime. Range: ustom designed to meet customers grinding profile requirements. imensions:.05-4 (1-100) wide. pplication: Highly accurate form dressing applications. lternative to roll dressing. lternative to profile dressing. Please state when ordering: Wheel type. Wheel size (diameter & width). Grit size and type. tool or component drawing will also be required. Rotatrim evices for ressing and Trueing For a fast, easy and cost effective way to restore, dress and true iamond and N wheels. Item entrifugal raking - For general purpose use ir riven - For large and very small diameter wheels Replacement Wheels 60 SI (5 pack) Stock No. 4710001 4720001 4730001 Natural ressing Tool Service Single Point ressers We can reset all our resettable diamonds into a comp letely new shank. P ressing Tools for N Profile Grinders Our polycrystalline diamond dressers are ideal for Voumard & Studer N Profile Grinders. The carbide post allows for secure mounting. Random diamond grain orientation on the dresser s points provide consistent results..217 5.51.125 3.20 Polished iamond Tools oth hisel tools and one tools can be relapped and regenerated. 10
www.abrasive-tech.com WORL HQURTRS United States P: 1.740 548.4100 F: 1.740 548.7617 UROPN HQURTRS United Kingdom P: 44.20.7471.0200 F: 44.20.7471.0202 SIN HQURTRS Singapore P: 65.6270.6878 F: 65.6270.6877 Go to www.abrasive-tech.com to order online or find a distributor near you. 2011 brasive Technology