LIFETIME UNIVERSAL DRAIN OVER THE RIM DRAIN AND STANDARD DRAIN BATH WASTE AND OVERFLOW WITH TOE TAPPER Installation Instructions 99.00.XXX Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. U.S. Patent No.,9,89, Patents Pending 799-00 Rev. C RECOMMENDED TOOLS Channel Locks Plumbers' Putty or Caulking Phillips Screwdriver ROUGH-IN DIMENSIONS STANDARD DRAIN OVER-THE-RIM DRAIN 7" NOTE: OVERFLOW E ASSEMBLY ROTATED 90 DEGREES IN THIS VIEW. UNDER SIDE OF OVERFLOW LEDGE *MIN. 7" MAX. 9-/" TOE TAPPER *MIN. 8" MAX. 0-/" TOE TAPPER -/" DIA. -/" DIA. " -/" OD TAILPIECE " -/" OD TAILPIECE MIN. -/" MAX. 9" MIN. -/" MAX. 9" DRAIN NUMBER BATH/WHIRLPOOL MODEL OVERFLOW TYPE 99-00 L ' X " OVER-THE-RIM 99-00 L-RHO ' X " IA-RHO OVER-THE-RIM 99-00 L-LHO ' X " IA-LHO OVER-THE-RIM 99-00 77L ' X " OVER-THE-RIM 99-00 7L ' X " OVER-THE-RIM 99-00 00L CORNER STANDARD 99-00 L OVAL STANDARD 99-00 7 RENAISSANCE STANDARD 99-00 90L SAVONA STANDARD 99-00 908L REMINISCENCE STANDARD 99-00 7L ELLISSE STANDARD 99-00 77L CADET ' X " STANDARD 99-00 77L CADET ' X " STANDARD 99-00 77L CADET CORNER STANDARD *NOTE: A smaller dimension can be accommodated by cutting pipe.
INSTALL AND ELL (STANDARD AND OVER-THE-RIM DRAINS) Apply putty to underside of () and drop into drain outlet. Slip RUBBER WASHER () on from below and thread () into DRAIN ELL ASSEMBLY (). PUTTY BATH DRAIN OUTLET INSTALL OVERFLOW ASSEMBLY AND DRAIN TEE (OVER-THE-RIM DRAIN) Loosen SLIP JOINT NUT & SEAL () and install onto OVERFLOW E (). Install OVERFLOW E ASSEMBLY () into the appropriate leg of the DRAIN TEE (). Apply sealant to threads of TAILPIECE () and thread into DRAIN TEE (). FIG.. Loosen SLIP JOINT NUT & SEAL () and install onto DRAIN ELL ASSEMBLY (). Install DRAIN ELL ASSEMBLY () into the horizontal leg of the DRAIN TEE (). FIG.. a FIG. FIG. INSTALL OVERFLOW ASSEMBLY AND DRAIN TEE (STANDARD DRAIN) Loosen SLIP JOINT NUT & SEAL () and install onto OVERFLOW E (). Install OVERFLOW E ASSEMBLY () into the appropriate leg of the DRAIN TEE (). Apply sealant to threads of TAILPIECE () and thread into DRAIN TEE (). Install OVERFLOW GASKET () to OVERFLOW E ASSEMBLY (). (Adjust OVERFLOW GASKET () to couture of tub. FIG.. Loosen SLIP JOINT NUT & SEAL () and install onto DRAIN ELL ASSEMBLY (). Install DRAIN ELL ASSEMBLY () into the horizontal leg of the DRAIN TEE (). FIG. FIG. FIG. 799-00 Rev. C
SECURE OVERFLOW ASSEMBLY TO (OVER-THE-RIM DRAIN) Install OVERFLOW GASKET () onto OVER FLOW FLANGE () using two strips of double-face tape (included). Apply a bead of silicone sealant to upper edge of 0VERFLOW GASKET (). Push OVER FLOW E ASSEMBLY () up flush against underside of ledge. Install and align mounting holes in RETAINING PLATE () with holes in OVER FLOW FLANGE (). Insert MOUNTING SCREWS () through RETAINING PLATE () into OVER FLOW FLANGE (). Note: RETAINING PLATE () must be installed as shown with open side facing out. Tighten SLIP JOINT NUTS (, a) to make water tight connections. a SECURE OVERFLOW ASSEMBLY TO (STANDARD DRAIN) Align the holes in the RETAINING PLATE () with those in the OVERFLOW FLANGE (). Install SCREWS (), tighten snugly (do not over tighten). The overflow gasket (behind tub wall) will begin to seal as the RETAINING PLATE () becomes tighter. The overflow gasket can be rotated for desired fit. a Align the ESCUTCHEON () with the RETAINING PLATE () and push onto RETAINING PLATE () until the ESCUTCHEON () snaps into place. UP FRONT Peel protective tape from the AMERICAN STANDARD LOGO (). Align LOGO () and press into place. When you are satisfied with the overall fit of the drain, go back and tighten all joints to make a water tight seal. INSTALL OVERFLOW ESCUTCHEON (OVER-THE-RIM DRAIN) Install OVERFLOW ESCUTCHEON () onto RETAINING PLATE (). Use MOUNTING SCREWS () to secure OVERFLOW ESCUTCHEON (). Fig.. Peel protective tape from the AMERICAN STANDARD LOGO (). Align LOGO () and press into place. Fig.. Thread TOE TAPPER () into (). FIG. FIG. 799-00 Rev. C
ABOVE FLOOR OUTLET INSTALLATION (OVER-THE-RIM DRAIN) Note: Waste outlet can be installed either above the floor or below floor. Fig.. For above floor drain outlet, Rotate DRAIN TEE ASSEMBLY () 90 degrees so TAILPIECE () faces out the back from tub as shown. TYPICAL ABOVE FLOOR INSTALLATION ROUGH FLOOR ABOVE FLOOR ROUGH BELOW FLOOR ROUGH ABOVE FLOOR OUTLET INSTALLATION (STANDARD DRAIN) Note: Waste outlet can be installed either above the floor or below floor. Fig.. For above floor drain outlet, Rotate DRAIN TEE ASSEMBLY () 90 degrees so TAILPIECE () faces out the back from tub as shown. TYPICAL ABOVE FLOOR INSTALLATION ROUGH FLOOR ABOVE FLOOR ROUGH BELOW FLOOR ROUGH 799-00 Rev. C
FRONT LIFETIME UNIVERSAL DRAIN OVER THE RIM DRAIN AND STANDARD DRAIN PRODUCT NUMBER 77-0070A AM. STD. BUBBLE LOGO 99.00.XXX 70-XXX0A OVERFLOW ESCUTCHEON W/BUBBLE LOGO 7009-0070A RETAINING PLATE WITH SCREWS 700-0070A OVERFLOW HOLD RING REPAIR KIT UP 798-0070A OVERFLOW FITTING 70-XXX0A OVERFLOW CAP REPAIR KIT 708-0070A OVERFLOW FITTING 7980-XXXOA TOE TAPPER DRAIN 798-XXX0A 7977-0070A WASHER Replace the "XXX" with appropriate finish code WHITE SATIN NICKEL 799-00 Rev. C 00 9 HOT LINE FOR HELP For toll-free information and answers to your questions, call: (800) -90 Weekdays 8:00 a.m. to :00 p.m. EST IN CANADA -800-87-09 (TORONTO -90-0-09) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 0-800-89--00 Product names listed herein are trademarks of American Standard Inc. AS America, Inc. 008