Seite 1 von 6 Seite 1 von 6 You will find a used-list in PDF format at: http://www.flexo-technic.de/pdf/used-list.pdf Code P 1275 List 1 08 2016 71 Made in Du Pont Cyrel* Processor incl. punch and 2 pin bars Barrel Kit on request Constantly serviced by a Du Pont technician! Year and Location 2006 Code D 1342 72 Made in Du Pont Cyrel* Dryer with Light-Finisher Constantly serviced by a Du Pont technician 2012 Code D 1339 51 Made for Flexo Technic NEW in 2014! Demo unit Dryer - REVLIS and UV-A Dryer with 6 drawers. Optional with New Light-Finisher or USED Code LF 1431 2014 Code 1343 73 Made in Du Pont Cyrel* Dryer 5 drying drawers with separate timers Constantly serviced by Du Pont technician Optional with USED Code LF 1431 2005 Code E 1173 63 Made in France Exposure BASF F V with new vacuum pump and vacuum stripes on the glass plate + new set of tubes The BASF F V exposure is a high quality, double side exposure unit. The BASF F V exposure is capable of main exposure and back exposing high quality photopolymer plates up to a maximum size of 52 x 80 inches (132 cm x 203 cm) WITHOUT MOVING THE PLATE from the exposure bed. 12/2002
Seite 2 von 6 Seite 2 von 6 Code 1276 65 Made in 92 x 120 cm - BASF Combi F III Processor with ECDLF incl. punch and 2 pin bars Barrel Kit on request 2001 IRAN Code 1273 66 Made in Italy 46 x 62 cm - BASF Combi F I Processor with ECDLF incl. punch and 2 pin bars Barrel Kit on request 1997 Scandinavia Code EDLF 1155 NEW in 2014! Demo unit 92 x 120 cm Exposure, Dryer and Light-Finisher - REVLIS 32 Made for Flexo Technic Automatic Lid opening 80W tubes 3 dryer drawers optional active cooling optional graphic touch screen 2013 Code EDLF 1154 13 Made in Italy 76 x 101 cm Exposure, Dryer and Light-Finisher Solution Graphiques Was in operation until June 2013 In best working order. 60W tubes 3 dryer drawers 2003 Code D 1339 NEW in 2014! Demo unit Dryer - REVLIS and UV-A Dryer with 6 drawers. 2014 51 Made for Flexo Technic Optional with New Light-Finisher or Code LF 1431 Code LF 1431 Light-Finisher for flexo printing plates MEKROM Concept 501 LF 67 Made in Italy 45 UV C 75 W tubes. 46 UV A 80W 10/R tubes. Automatic defective lamp detection. 9 memory channels. Electronic ballasts for UV C and UV A tubes. Cooling system. 2 Exhaust blowers. 2008
Seite 3 von 6 Seite 3 von 6 Code E 1160 45 Made in France 76 x 101 cm - Exposure for flexo plate processing BASF F III In very good condition. Ready to work for many more years. 80W tubes. UV A output 12,8 Nm 1990 Code 2026 70 Made in France Du Pont Cyrel* Microflex 1320 with proofing. For sleeve and cylinder. This high performance mounter can mount all photopolymer plates onto cylinders or sleeves up to a maximum size of 52 inches wide (1320mm) and repeats up to 39.9 inches (1016mm). The unit features computer-controlled cameras with a magnification of 40X In very good condition. 1997 MEXICO Code E 1168 59 Made in 90 x 120 cm - CTF FlexoLaser - Medio Standard resolution: 2540 dpi 200 lpi 80 lcm Speed: 2 qm/hour (OPTICS 15) NEW PRICE is: 117.000 Euro for the laser SOFTWARE Xante Symphonie Flexoavailable for extra 5.000 Euro 2008 INDIA Code E 1169 60 Made in 106,7 x 152,4 cm - HELL CtP Flexo Laser, Hell Gravure F 2000 fully functional CtP Flexo Laser for any kind of digital flexo plates (LAMS) build in 2002 but fully refurbished and technically updated in 2004 reliable fibre laser system with 8 single laser units (only 6 in operation) 6 laser units with only 3000 working hours, 2 units with only 1500 working hours 2540 dpi 2002 BULGARIA Code LF 1430 28 Made in France 92 x 120 cm - Light-Finisher for flexo printing plates Du Pont Cyrel* 1002 LF The unit is designed with an exposure bank fitted with 27 UV A exposure lamps, a control panel, one drawer, fitted with an electronically timer. 1997 Cutter 45 + 90 Made in U.K. Flexo Plate Cutter 45 + 90 in different sizes available: 98 cm 118 cm 157 cm 218 cm ON REQUEST MORE THEN 100 CUTTERS WERE WORLD WIDE Code 12149 Solvent recovery with or without vacuum - IST 202 Eco, stainless steel
Seite 4 von 6 64 Made in Italy The working cycle is completely automatic and driven by a digital microprocessor, which enables several operational functions.this model ECO 202 is not standard, with separate heating tank for the oil and oil circulation pump. It has also a bottom discharging valve and not a lateral one, so a better drainage of the residuals. At last but not least this unit is equipped with the last version of our plc, with touch screen panel and display. 2009 to JORDANIA Code 12204 48 Made in the Netherlands POLYMOUNT PLATE CLEANER 800 Plate Cleaner after printing There is one aspect of plate cleaning that remains somewhat inconsistent that has a tremendous effect on plate life and performance, and that is a consistent deep cleaning into the screen areas of the plate. 800 Plate Cleaner (800 x 1200mm), OTHER SIZES AVAILABLE. Please ask. 2008 to GEORGIA Code 1175 LETTERPRESS 90 x 120 cm - HOUTSTRA POLYMERO HP 400 exposure Hydraulik lid opening N/A 69 Made in NL NEW HIGH QUALITY EQUIPMENT ON REQUEST Code P 1272 66 x 86 cm - REVLIS Pro II Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars or alternatively with EDLF or 4UP EDLF 47 Made for Flexo Technic Code ECDLF 1155 separate EDLF 66 x 86 cm OR Code 4 UP ECDLF can be placed under the pre dryer Code P 1267 92 x 120 cm - REVLIS Pro II Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars or alternatively with ECDLF or 4UP EDLF 46 Made for Flexo Technic Code E 1155 separate ECDLF 92 x 120 cm OR Code 4 UP ECDLF can be placed under the pre-dryer Seite 4 von 6
Seite 5 von 6 Seite 5 von 6 Code P 1275 74 Made for Flexo Technic Code DLF 1339 51 Made for Flexo Technic Code D 1166 55 Made for Flexo Technic REVLIS Pro IV Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars REVLIS Dryer and Light-Finisher/Post-Exposure - UV-C and UV-A Dryer with 6 drawers. EACH unit is also available as single unit. REVLIS Top Lift Exposure - UV-A and UV-C Pre and Main exposure without turning the plate. YERKELESS up and down movement of the P LIFT THIS IS UNIQUE: You position the control bord were and when you want it. THIS IS UNIQUE, too: For easy maintenance the glass plate lifts up with the P LIFT OPTION: One side exposure with cooled bed. Code 1170 This information was sent to lte_1@menara.ma. If you no longer wish to receive these emails, please reply to this message with "unsubscribe" in the subject line or simply click on the following link: Unsubscribe: Your email address Come and visit us in our show room and ware house!
Seite 6 von 6 Seite 6 von 6 The shown prices are net prices. You need to add your commission, crating, transportation and installation costs. ONLY the prices shown in our quotation or pro-forma invoice are binding and valid. ALL USED machinery is offered on an as is, ex site basis unless otherwise stated in writing, subject to prior sale and/or availability. All used machines are offered subject to remaining unsold. Please note our payment terms for USED machine 100% deposit with official order On NEW articles your warranty is 12 month on all parts besides brushes, tubes and vacuum foil. The parts will be shipped on your account. All specifications are correct to the best of our knowledge but it is the customer's responsibility to ensure him self that the equipment meets his requirements. Please note our payment terms for NEW machinery 30% deposit with official order 70% before crating resp. when ready for shipment. If this is of interest for you, please come back with any further question you might have Flexo-Technic Handels GmbH Mr. Reiner Roosen Von-Eiff-Strasse 23 63456 Hanau www.flexo-technic.de www.pile-turner.biz Phone 0049-6181-6709055 Fax 0049-6181-6709056 http://www.flexo-technic.de/contact.html
Seite 1 von 6 Seite 1 von 6 You will find a used-list in PDF format at: http://www.flexo-technic.de/pdf/used-list.pdf Code P 1275 List 1 08 2016 71 Made in Du Pont Cyrel* Processor incl. punch and 2 pin bars Barrel Kit on request Constantly serviced by a Du Pont technician! Year and Location 2006 Code D 1342 72 Made in Du Pont Cyrel* Dryer with Light-Finisher Constantly serviced by a Du Pont technician 2012 Code D 1339 51 Made for Flexo Technic NEW in 2014! Demo unit Dryer - REVLIS and UV-A Dryer with 6 drawers. Optional with New Light-Finisher or USED Code LF 1431 2014 Code 1343 73 Made in Du Pont Cyrel* Dryer 5 drying drawers with separate timers Constantly serviced by Du Pont technician Optional with USED Code LF 1431 2005 Code E 1173 63 Made in France Exposure BASF F V with new vacuum pump and vacuum stripes on the glass plate + new set of tubes The BASF F V exposure is a high quality, double side exposure unit. The BASF F V exposure is capable of main exposure and back exposing high quality photopolymer plates up to a maximum size of 52 x 80 inches (132 cm x 203 cm) WITHOUT MOVING THE PLATE from the exposure bed. 12/2002
Seite 2 von 6 Seite 2 von 6 Code 1276 65 Made in 92 x 120 cm - BASF Combi F III Processor with ECDLF incl. punch and 2 pin bars Barrel Kit on request 2001 IRAN Code 1273 66 Made in Italy 46 x 62 cm - BASF Combi F I Processor with ECDLF incl. punch and 2 pin bars Barrel Kit on request 1997 Scandinavia Code EDLF 1155 NEW in 2014! Demo unit 92 x 120 cm Exposure, Dryer and Light-Finisher - REVLIS 32 Made for Flexo Technic Automatic Lid opening 80W tubes 3 dryer drawers optional active cooling optional graphic touch screen 2013 Code EDLF 1154 13 Made in Italy 76 x 101 cm Exposure, Dryer and Light-Finisher Solution Graphiques Was in operation until June 2013 In best working order. 60W tubes 3 dryer drawers 2003 Code D 1339 NEW in 2014! Demo unit Dryer - REVLIS and UV-A Dryer with 6 drawers. 2014 51 Made for Flexo Technic Optional with New Light-Finisher or Code LF 1431 Code LF 1431 Light-Finisher for flexo printing plates MEKROM Concept 501 LF 67 Made in Italy 45 UV C 75 W tubes. 46 UV A 80W 10/R tubes. Automatic defective lamp detection. 9 memory channels. Electronic ballasts for UV C and UV A tubes. Cooling system. 2 Exhaust blowers. 2008
Seite 3 von 6 Seite 3 von 6 Code E 1160 45 Made in France 76 x 101 cm - Exposure for flexo plate processing BASF F III In very good condition. Ready to work for many more years. 80W tubes. UV A output 12,8 Nm 1990 Code 2026 70 Made in France Du Pont Cyrel* Microflex 1320 with proofing. For sleeve and cylinder. This high performance mounter can mount all photopolymer plates onto cylinders or sleeves up to a maximum size of 52 inches wide (1320mm) and repeats up to 39.9 inches (1016mm). The unit features computer-controlled cameras with a magnification of 40X In very good condition. 1997 MEXICO Code E 1168 59 Made in 90 x 120 cm - CTF FlexoLaser - Medio Standard resolution: 2540 dpi 200 lpi 80 lcm Speed: 2 qm/hour (OPTICS 15) NEW PRICE is: 117.000 Euro for the laser SOFTWARE Xante Symphonie Flexoavailable for extra 5.000 Euro 2008 INDIA Code E 1169 60 Made in 106,7 x 152,4 cm - HELL CtP Flexo Laser, Hell Gravure F 2000 fully functional CtP Flexo Laser for any kind of digital flexo plates (LAMS) build in 2002 but fully refurbished and technically updated in 2004 reliable fibre laser system with 8 single laser units (only 6 in operation) 6 laser units with only 3000 working hours, 2 units with only 1500 working hours 2540 dpi 2002 BULGARIA Code LF 1430 28 Made in France 92 x 120 cm - Light-Finisher for flexo printing plates Du Pont Cyrel* 1002 LF The unit is designed with an exposure bank fitted with 27 UV A exposure lamps, a control panel, one drawer, fitted with an electronically timer. 1997 Cutter 45 + 90 Made in U.K. Flexo Plate Cutter 45 + 90 in different sizes available: 98 cm 118 cm 157 cm 218 cm ON REQUEST MORE THEN 100 CUTTERS WERE WORLD WIDE Code 12149 Solvent recovery with or without vacuum - IST 202 Eco, stainless steel
Seite 4 von 6 64 Made in Italy The working cycle is completely automatic and driven by a digital microprocessor, which enables several operational functions.this model ECO 202 is not standard, with separate heating tank for the oil and oil circulation pump. It has also a bottom discharging valve and not a lateral one, so a better drainage of the residuals. At last but not least this unit is equipped with the last version of our plc, with touch screen panel and display. 2009 to JORDANIA Code 12204 48 Made in the Netherlands POLYMOUNT PLATE CLEANER 800 Plate Cleaner after printing There is one aspect of plate cleaning that remains somewhat inconsistent that has a tremendous effect on plate life and performance, and that is a consistent deep cleaning into the screen areas of the plate. 800 Plate Cleaner (800 x 1200mm), OTHER SIZES AVAILABLE. Please ask. 2008 to GEORGIA Code 1175 LETTERPRESS 90 x 120 cm - HOUTSTRA POLYMERO HP 400 exposure Hydraulik lid opening N/A 69 Made in NL NEW HIGH QUALITY EQUIPMENT ON REQUEST Code P 1272 66 x 86 cm - REVLIS Pro II Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars or alternatively with EDLF or 4UP EDLF 47 Made for Flexo Technic Code ECDLF 1155 separate EDLF 66 x 86 cm OR Code 4 UP ECDLF can be placed under the pre dryer Code P 1267 92 x 120 cm - REVLIS Pro II Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars or alternatively with ECDLF or 4UP EDLF 46 Made for Flexo Technic Code E 1155 separate ECDLF 92 x 120 cm OR Code 4 UP ECDLF can be placed under the pre-dryer Seite 4 von 6
Seite 5 von 6 Seite 5 von 6 Code P 1275 74 Made for Flexo Technic Code DLF 1339 51 Made for Flexo Technic Code D 1166 55 Made for Flexo Technic REVLIS Pro IV Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars REVLIS Dryer and Light-Finisher/Post-Exposure - UV-C and UV-A Dryer with 6 drawers. EACH unit is also available as single unit. REVLIS Top Lift Exposure - UV-A and UV-C Pre and Main exposure without turning the plate. YERKELESS up and down movement of the P LIFT THIS IS UNIQUE: You position the control bord were and when you want it. THIS IS UNIQUE, too: For easy maintenance the glass plate lifts up with the P LIFT OPTION: One side exposure with cooled bed. Code 1170 This information was sent to lte_1@menara.ma. If you no longer wish to receive these emails, please reply to this message with "unsubscribe" in the subject line or simply click on the following link: Unsubscribe: Your email address Come and visit us in our show room and ware house!
Seite 6 von 6 Seite 6 von 6 The shown prices are net prices. You need to add your commission, crating, transportation and installation costs. ONLY the prices shown in our quotation or pro-forma invoice are binding and valid. ALL USED machinery is offered on an as is, ex site basis unless otherwise stated in writing, subject to prior sale and/or availability. All used machines are offered subject to remaining unsold. Please note our payment terms for USED machine 100% deposit with official order On NEW articles your warranty is 12 month on all parts besides brushes, tubes and vacuum foil. The parts will be shipped on your account. All specifications are correct to the best of our knowledge but it is the customer's responsibility to ensure him self that the equipment meets his requirements. Please note our payment terms for NEW machinery 30% deposit with official order 70% before crating resp. when ready for shipment. If this is of interest for you, please come back with any further question you might have Flexo-Technic Handels GmbH Mr. Reiner Roosen Von-Eiff-Strasse 23 63456 Hanau www.flexo-technic.de www.pile-turner.biz Phone 0049-6181-6709055 Fax 0049-6181-6709056 http://www.flexo-technic.de/contact.html
Seite 1 von 6 Seite 1 von 6 You will find a used-list in PDF format at: http://www.flexo-technic.de/pdf/used-list.pdf Code P 1275 List 1 08 2016 71 Made in Du Pont Cyrel* Processor incl. punch and 2 pin bars Barrel Kit on request Constantly serviced by a Du Pont technician! Year and Location 2006 Code D 1342 72 Made in Du Pont Cyrel* Dryer with Light-Finisher Constantly serviced by a Du Pont technician 2012 Code D 1339 51 Made for Flexo Technic NEW in 2014! Demo unit Dryer - REVLIS and UV-A Dryer with 6 drawers. Optional with New Light-Finisher or USED Code LF 1431 2014 Code 1343 73 Made in Du Pont Cyrel* Dryer 5 drying drawers with separate timers Constantly serviced by Du Pont technician Optional with USED Code LF 1431 2005 Code E 1173 63 Made in France Exposure BASF F V with new vacuum pump and vacuum stripes on the glass plate + new set of tubes The BASF F V exposure is a high quality, double side exposure unit. The BASF F V exposure is capable of main exposure and back exposing high quality photopolymer plates up to a maximum size of 52 x 80 inches (132 cm x 203 cm) WITHOUT MOVING THE PLATE from the exposure bed. 12/2002
Seite 2 von 6 Seite 2 von 6 Code 1276 65 Made in 92 x 120 cm - BASF Combi F III Processor with ECDLF incl. punch and 2 pin bars Barrel Kit on request 2001 IRAN Code 1273 66 Made in Italy 46 x 62 cm - BASF Combi F I Processor with ECDLF incl. punch and 2 pin bars Barrel Kit on request 1997 Scandinavia Code EDLF 1155 NEW in 2014! Demo unit 92 x 120 cm Exposure, Dryer and Light-Finisher - REVLIS 32 Made for Flexo Technic Automatic Lid opening 80W tubes 3 dryer drawers optional active cooling optional graphic touch screen 2013 Code EDLF 1154 13 Made in Italy 76 x 101 cm Exposure, Dryer and Light-Finisher Solution Graphiques Was in operation until June 2013 In best working order. 60W tubes 3 dryer drawers 2003 Code D 1339 NEW in 2014! Demo unit Dryer - REVLIS and UV-A Dryer with 6 drawers. 2014 51 Made for Flexo Technic Optional with New Light-Finisher or Code LF 1431 Code LF 1431 Light-Finisher for flexo printing plates MEKROM Concept 501 LF 67 Made in Italy 45 UV C 75 W tubes. 46 UV A 80W 10/R tubes. Automatic defective lamp detection. 9 memory channels. Electronic ballasts for UV C and UV A tubes. Cooling system. 2 Exhaust blowers. 2008
Seite 3 von 6 Seite 3 von 6 Code E 1160 45 Made in France 76 x 101 cm - Exposure for flexo plate processing BASF F III In very good condition. Ready to work for many more years. 80W tubes. UV A output 12,8 Nm 1990 Code 2026 70 Made in France Du Pont Cyrel* Microflex 1320 with proofing. For sleeve and cylinder. This high performance mounter can mount all photopolymer plates onto cylinders or sleeves up to a maximum size of 52 inches wide (1320mm) and repeats up to 39.9 inches (1016mm). The unit features computer-controlled cameras with a magnification of 40X In very good condition. 1997 MEXICO Code E 1168 59 Made in 90 x 120 cm - CTF FlexoLaser - Medio Standard resolution: 2540 dpi 200 lpi 80 lcm Speed: 2 qm/hour (OPTICS 15) NEW PRICE is: 117.000 Euro for the laser SOFTWARE Xante Symphonie Flexoavailable for extra 5.000 Euro 2008 INDIA Code E 1169 60 Made in 106,7 x 152,4 cm - HELL CtP Flexo Laser, Hell Gravure F 2000 fully functional CtP Flexo Laser for any kind of digital flexo plates (LAMS) build in 2002 but fully refurbished and technically updated in 2004 reliable fibre laser system with 8 single laser units (only 6 in operation) 6 laser units with only 3000 working hours, 2 units with only 1500 working hours 2540 dpi 2002 BULGARIA Code LF 1430 28 Made in France 92 x 120 cm - Light-Finisher for flexo printing plates Du Pont Cyrel* 1002 LF The unit is designed with an exposure bank fitted with 27 UV A exposure lamps, a control panel, one drawer, fitted with an electronically timer. 1997 Cutter 45 + 90 Made in U.K. Flexo Plate Cutter 45 + 90 in different sizes available: 98 cm 118 cm 157 cm 218 cm ON REQUEST MORE THEN 100 CUTTERS WERE WORLD WIDE Code 12149 Solvent recovery with or without vacuum - IST 202 Eco, stainless steel
Seite 4 von 6 64 Made in Italy The working cycle is completely automatic and driven by a digital microprocessor, which enables several operational functions.this model ECO 202 is not standard, with separate heating tank for the oil and oil circulation pump. It has also a bottom discharging valve and not a lateral one, so a better drainage of the residuals. At last but not least this unit is equipped with the last version of our plc, with touch screen panel and display. 2009 to JORDANIA Code 12204 48 Made in the Netherlands POLYMOUNT PLATE CLEANER 800 Plate Cleaner after printing There is one aspect of plate cleaning that remains somewhat inconsistent that has a tremendous effect on plate life and performance, and that is a consistent deep cleaning into the screen areas of the plate. 800 Plate Cleaner (800 x 1200mm), OTHER SIZES AVAILABLE. Please ask. 2008 to GEORGIA Code 1175 LETTERPRESS 90 x 120 cm - HOUTSTRA POLYMERO HP 400 exposure Hydraulik lid opening N/A 69 Made in NL NEW HIGH QUALITY EQUIPMENT ON REQUEST Code P 1272 66 x 86 cm - REVLIS Pro II Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars or alternatively with EDLF or 4UP EDLF 47 Made for Flexo Technic Code ECDLF 1155 separate EDLF 66 x 86 cm OR Code 4 UP ECDLF can be placed under the pre dryer Code P 1267 92 x 120 cm - REVLIS Pro II Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars or alternatively with ECDLF or 4UP EDLF 46 Made for Flexo Technic Code E 1155 separate ECDLF 92 x 120 cm OR Code 4 UP ECDLF can be placed under the pre-dryer Seite 4 von 6
Seite 5 von 6 Seite 5 von 6 Code P 1275 74 Made for Flexo Technic Code DLF 1339 51 Made for Flexo Technic Code D 1166 55 Made for Flexo Technic REVLIS Pro IV Flexo plate processor - SINGLE processor incl. pre wash for digital plates incl. punch and 3 pin bars REVLIS Dryer and Light-Finisher/Post-Exposure - UV-C and UV-A Dryer with 6 drawers. EACH unit is also available as single unit. REVLIS Top Lift Exposure - UV-A and UV-C Pre and Main exposure without turning the plate. YERKELESS up and down movement of the P LIFT THIS IS UNIQUE: You position the control bord were and when you want it. THIS IS UNIQUE, too: For easy maintenance the glass plate lifts up with the P LIFT OPTION: One side exposure with cooled bed. Code 1170 This information was sent to lte_1@menara.ma. If you no longer wish to receive these emails, please reply to this message with "unsubscribe" in the subject line or simply click on the following link: Unsubscribe: Your email address Come and visit us in our show room and ware house!
Seite 6 von 6 Seite 6 von 6 The shown prices are net prices. You need to add your commission, crating, transportation and installation costs. ONLY the prices shown in our quotation or pro-forma invoice are binding and valid. ALL USED machinery is offered on an as is, ex site basis unless otherwise stated in writing, subject to prior sale and/or availability. All used machines are offered subject to remaining unsold. Please note our payment terms for USED machine 100% deposit with official order On NEW articles your warranty is 12 month on all parts besides brushes, tubes and vacuum foil. The parts will be shipped on your account. All specifications are correct to the best of our knowledge but it is the customer's responsibility to ensure him self that the equipment meets his requirements. Please note our payment terms for NEW machinery 30% deposit with official order 70% before crating resp. when ready for shipment. If this is of interest for you, please come back with any further question you might have Flexo-Technic Handels GmbH Mr. Reiner Roosen Von-Eiff-Strasse 23 63456 Hanau www.flexo-technic.de www.pile-turner.biz Phone 0049-6181-6709055 Fax 0049-6181-6709056 http://www.flexo-technic.de/contact.html