FEATES APPLICATIO S 1µA to 1mA Operation.2%/V egulation.8v to 4V Operating Voltage Can be sed as Linear Temperature Sensor Draws No everse Current Supplied in Standard Transistor Packages Current Mode Temperature Sensing Constant Current Source for Shunt eferences Cold Junction Compensation Constant-Gain Bias for Bipolar Differential Stage Micropower Bias Networks Buffer for Photoconductive Cell Current Limiter, LTC and LT are registered trademarks of Linear Technology Corporation. TYPICAL APPLICATIO emote Temperature Sensor with Voltage Output DESCIPTIO LM134 Series Constant Current Source and Temperature Sensor The LM134 is a three-terminal current source designed to operate at current levels from 1µA to 1mA, as set by an external resistor. The device operates as a true twoterminal current source, requiring no extra power connections or input signals. egulation is typically.2%/v and terminal-to-terminal voltage can range from 8mV to 4V. Because the operating current is directly proportional to absolute temperature in degrees Kelvin, the device will also find wide applications as a temperature sensor. The temperature dependence of the operating current is.336%/ C at room temperature. For example, a device operating at 298µA will have a temperature coefficient of 1µA/ C. The temperature dependence is extremely accurate and repeatable. Devices specified as temperature sensors in the 1µA to 1mA range are the LM134-3, LM234-3 and the LM134-6, LM234-6, with the dash numbers indicating ±3 C and ±6 C accuracies, respectively. If a zero temperature coefficient current source is required, this is easily achieved by adding a diode and a resistor. Operating Current vs Temperature 5 225 SET 226Ω LM234-3 5V 1 1k 1mV/ K TA1a TEMPEATE ( K) 4 3 2 1 SET = 226Ω 125 25 75 175 TEMPEATE ( C) 275 1 2 3 4 5 OPEATING CENT (µa) TA1b 1
ABSOLTE AXI ATI GS W W W to Forward Voltage LM134... 4V LM134-3/LM134-6/LM234-3/ LM234-6/... 3V to everse Voltage... 2V Pin to Voltage... 5V Set Current... 1mA (Note 1) Power Dissipation... 2mW Operating Temperature ange LM134 (OBSOLETE)... 55 C to 125 C LM234-3/LM234-6... 25 C to 1 C... C to 7 C Storage Temperature ange... 65 C to 15 C Lead Temperature (Soldering, 1 sec)... 3 C PACKAGE/ODE I FO W ATIO BOTTOM VIEW ODE PAT NMBE CENT SOCE TEMP SENSO BOTTOM VIEW ODE PAT NMBE CENT SOCE TEMP SENSO H PACKAGE 3-LEAD TO-46 METAL CAN T JMAX = 15 C, θ JA = 44 C/W, θ JA = 8 C/W LM134H H OBSOLETE PACKAGE Consider the S8 or Z Packages for Alternate Source LM134H-3 LM234H-3 LM134H-6 LM234H-6 Z PACKAGE 3-LEAD PLASTIC TO-92 T JMAX = 1 C, θ JA = 16 C/W Z LM234Z-3 LM234Z-6 NC 1 2 3 4 8 NC 7 NC 6 NC 5 NC S8 PACKAGE 8-LEAD PLASTIC SO T JMAX = 1 C, θ JA = 18 C/W ODE PAT NMBE S8 S8 PAT MAKING 334 Consult LTC Marketing for availability of LM234Z-3 and LM234Z-6 2
ELECTICAL CHAACTEISTICS CENT SOCE (Note 2) LM134 Series LM134 SYMBOL PAAMETE CONDITIONS MIN TYP MAX MIN TYP MAX NITS Set Current Error, = 2.5V 1µA 1mA 3 6 % (Note 3) 1mA < 5mA 5 8 % 2µA < 1µA 8 12 % atio of Set Current to 1µA 1mA 14 18 23 14 18 26 Current 1mA 5mA 14 14 2µA 1µA 18 23 18 26 V MIN Minimum Operating Voltage 2µA 1µA.8.8 V 1µA < 1mA.9.9 V 1mA < 5mA 1. 1. V Average Change in Set Current 1.5V 5V.2.5.2.1 %/V with Input Voltage 2µA 1mA 5V V MAX (Note 5).1.3.1.5 %/V 1.5V V 5V.3.3 %/V 1mA < 5mA 5V V V MAX (Note 5).2.2 %/V Temperature Dependence of 25µA 1mA.96 1.4.96 1.4 Set Current (Note 4) C S Effective Shunt Capacitance 15 15 pf TEMPEATE SENSO (Note 2) LM134-3,LM234-3 LM134-6, LM234-6 SYMBOL PAAMETE CONDITIONS MIN TYP MAX MIN TYP MAX NITS Set Current Error, = 2.5V 1µA 1mA ±1 ±2 % (Note 3) T j = 25 C Equivalent Temperature Error ±3 ±6 C atio of Set Current to 1µA 1mA 14 18 26 14 18 26 Current V MIN Minimum Operating Voltage 1µA 1mA.9.9 V Average Change in Set Current 1.5V 5V.2.5.2.1 %/V with Input Voltage 1µA 1mA 5V 3V.1.3.1.5 %/V Temperature Dependence of 1µA 1mA.98 1.2.97 1.3 Set Current (Note 4) Equivalent Slope Error ±2 ±3 % C S Effective Shunt Capacitance 15 15 pf Note 1: Absolute Maximum atings are those values beyond which the life of a device may be impaired. Note 2: nless otherwise specified, tests are performed at T j = 25 C with pulse testing so that junction temperature does not change during test. Note 3: Set current is the current flowing into the pin. It is determined by the following formula: = 67.7mV/ SET (at 25 C). Set current error is expressed as a percent deviation from this amount. increases at.336%/ C at T j = 25 C. Note 4: is nominally directly proportional to absolute temperature ( K). at any temperature can be calculated from: = I O (T/T O ) where I O is measured at T O ( K). Note 5: V MAX = 4V for LM134 and 3V for other grades. 3
TYPICAL PEFO A CE CHAACTEISTICS W 1 9 Output Impedance 1 Maximum Slew ate for Linear Operation Start-p IMPEDANCE (Ω) 1 8 1 7 I = 1µA I = 1µA I = 1mA SLEW ATE (V/µs) 1..1.1 1µA µa 1µA µa 1mA ma 2µs 5µs 5µs 1 6 1 1 1k 1k FEQENCY (Hz).1 1 1 1 1 1 (µa) 5V INPT V TIME (*NOTE SCALE CHANGES FO EACH CENT LEVEL) 134 G1 134 G2 134 G3 ISET (%) Transient esponse Voltage Across SET Current Noise 2 2µs 1 = 1mA 1 5 TO = 5V V =.4V t r, f = 5ns 5 1 1 2 1µs 5µs TIME = 1µA = 1µA (*NOTE SCALE CHANGES FO EACH CENT LEVEL) 134 G4 VOLTAGE (mv) 86 82 78 74 7 66 62 58 54 5 46 5 25 25 5 75 1 125 TEMPEATE ( C) 1314/15 G1 CENT (pa/ Hz) 1k 1k 1 1 = 5mA = 1mA = 1µA = 1µA 1 1 1 1k 1k 1k FEQENCY (Hz) 134 G6 Turn-On Voltage 1mA T j = 25 C 1mA 1µA SET = 14Ω SET = 68Ω SET = 68Ω 1µA SET = 6.8k 1µA.4.6.8 1. 1.2 1.4 TO VOLTAGE 134 G2 ATIO Operating Current vs atio of to Current Temperature 21 2 19 18 17 16 15 14 13 12 11 1µA 1µA 1mA 1mA 134 G8 TEMPEATE ( K) 5 SET = 226Ω 4 3 2 1 175 275 1 2 3 4 5 OPEATING CENT (µa) 134 G9 225 125 25 75 TEMPEATE ( C) 4
APPLICATIO S I FO Basic Theory of Operation ATIO W The equivalent circuit of the LM134 is shown in Figure 1. A reference voltage of 64mV is applied to the minus input of A1 with respect to the pin. A1 serves the drive to Q2 to keep the pin at 64mV, independent of the value of SET. Transistor Q1 is matched to Q2 at a 17:1 ratio so that the current flowing out of the pin is always 1/18 of the total current into the pin. This total current is called and is equal to: 64mV 18 67 7mV 17 =. SET Q1 SET A1 Figure 1. The 67.7mV equivalent reference voltage is directly proportional to absolute temperature in degrees Kelvin (see curve, Operating Current vs Temperature ). This means that the reference voltage can be plotted as a straight line going from mv at absolute zero temperature to 67.7mV at 298 K (25 C). The slope of this line is 67.7mV/298 = 227µV/ C. The accuracy of the device is specified as a percent error at room temperature, or in the case of the -3 and -6 devices, as both a percent error and an equivalent temperature error. The LM134 operating current changes at a percent rate equal to (1)(227µV/ C)/(67.7mV) =.336%/ C at 25 C, so each operating current error is equivalent to 3 C temperature error when the device is used as a temperature sensor. The slope accuracy (temperature coefficient) of the LM134 is expressed as a ratio compared to unity. The LM134-3, for instance, is specified at.98 to 1.2, indicating that the maximum slope error of + 64mV Q2 + SET 134 F1 the device is ±2% when the room temperature current is set to the exact desired value. Supply Voltage Slew ate At slew rates above a given threshold (see curve), the LM134 may exhibit nonlinear current shifts. The slewing rate at which this occurs is directly proportional to. At = 1µA, maximum dv/dt is.1v/µs; at = 1mA, the limits is 1V/µs. Slew rates above the limit do not harm the LM134, or cause large currents to flow. Thermal Effects Internal heating can have a significant effect on current regulation for greater than 1µA. For example, each 1V increase across the LM134 at = 1mA will increase junction temperature by.4 C in still air. Output current ( ) has a temperature coefficient of.33%/ C, so the change in current due to temperature rise will be (.4)(.33) =.132%. This is a 1:1 degradation in regulation compared to true electrical effects. Thermal effects, therefore, must be taken into account when DC regulation is critical and exceeds 1µA. Heat sinking of the TO-46 package or the TO-92 leads can reduce this effect by more than 3:1. Shunt Capacitance In certain applications, the 15pF shunt capacitance of the LM134 may have to be reduced, either because of loading problems or because it limits the AC output impedance of the current source. This can be easily accomplished by buffering the LM134 with a FET, as shown in the applications. This can reduce capacitance to less than 3pF and improve regulation by at least an order of magnitude. DC characteristics (with the exception of minimum input voltage) are not affected. Noise Current noise generated by the LM134 is approximately 4 times the shot noise of a transistor. If the LM134 is used as an active load for a transistor amplifier, input referred noise will be increased by about 12dB. In many cases, this is acceptable and a single stage amplifier can be built with a voltage gain exceeding 2. 5
APPLICATIO S I FO ATIO W Lead esistance The sense voltage which determines the operating current of the LM134 is less than 1mV. At this level, thermocouple or lead resistance effects should be minimized by locating the current setting resistor physically close to the device. Sockets should be avoided if possible. It takes only.7ω contact resistance to reduce output current by at the 1mA level. Start-p Time The LM134 is designed to operate at currents as low as 1µA. This requires that internal biasing current be well below that level because the device achieves its wide operating current range by using part of the operating current as bias current for the internal circuitry. To ensure start-up, however, a fixed trickle current must be provided internally. This is typically in the range of 2nA to 2nA and is provided by the special ultralow I DDS FETs shown in the Schematic Diagrams as Q7 and Q8. The start-up time of the LM134 is determined by the I DSS of these FETs and the capacitor C1. This capacitor must charge to approximately 5mV before Q3 turns on to start normal circuit operation. This takes as long as (5mV)(5pF)/(2nA) = 1.25ms for very low I DSS values. sing the LM134 as a Temperature Sensor Because it has a highly linear output characteristic, the LM134 makes a good temperature sensor. It is particularly useful in remote sensing applications because it is a current output device and is therefore not affected by long wire runs. It is easy to calibrate, has good long term stability and can be interfaced directly with most data acquisition systems, eliminating the expensive preamplifiers required for thermocouples and platinum sensors. A typical temperature sensor application is shown in Figure 2. The LM134 operating current at 25 C is set at 298µA by the 226Ω resistor, giving an output of 1µA/ K. The current flows through the twisted pair sensor leads to the 1k termination resistor, which converts the current output to a voltage of 1mV/ K referred to ground. The voltage across the 1k resistor will be 2.98V at 25 C, with a slope of 1mV/ C. The simplest way to convert this signal to a Centigrade scale is to subtract a constant 2.73V in software. Alternately, a hardware conversion can be used, as shown in Figure 3, using an LT19 as a level shifter to offset the output to a Centigrade scale. The resistor ( SET ) used to set the operating current of the LM134 in temperature sensing applications should have low temperature coefficient and good long term stability. A 3ppm/ C drift in the resistor will change the slope of the temperature sensor by, assuming that the resistor is at the same temperature as the sensor, which is usually the case since the resistor should be located physically close to the LM134 to prevent errors due to wire resistance. A long term shift of.3% in the resistor will create a 1 C temperature error. The long term drift of the LM134 is typically much better than this, so stable resistors must be used for best long term performance. Calibration of the LM134 as a temperature sensor is extremely easy. eferring to Figure 2, calibration is achieved by trimming the termination resistor. This theoretically trims both zero and slope simultaneously for Centigrade and Fahrenheit applications. The initial errors in the LM134 are directly proportional to absolute temperature, just like the actual output. This allows the sensor to be trimmed at any temperature and have the slope error be corrected at the same time. esidual slope error is typically less than after this single trim is completed. TO DATA ACQISITION SYSTEM 1mV/ K 9.53k 1k CALIBATE V S 5V I = 1µA/ K Figure 2 Kelvin Temperature Sensor LM234-3 SET 226Ω 134 F2 6
APPLICATIO S I FO V S 4V ATIO W The two trims shown in Figure 3 are still intended to be a one point temperature calibration, where the zero and the slope are trimmed at a single temperature. The LT19 reference is adjusted to give 2.7V at node a at T SENSO = 25 C. The 1k trimmer then adjusts the output for.25v, completing the calibration. If the calibration is to be done at a temperature other than 25 C, trim the LT19 for 2.725 (1µA)[T SENSO ( C)](1Ω) at node a, then adjust the 1k trimmer for proper output. If higher accuracy is required, a two point calibration technique can be used. In Figure 4, separate zero and slope trims are provided. esidual nonlinearity is now the limitation on accuracy. Nonlinearity of the LM134 in a 1 C span is typically less than.5 C. This particular method of trimming has the advantage that the slope trim does not interact with the zero trim. Trim procedure is to adjust for zero output with T SENSO = C, then trim slope for proper output at some convenient second temperature. No further trimming is required. OTPT 1mV/ C a 9.53k 1k SLOPE ADJ 1Ω 1k LT19 LM134-3 SET 226Ω LM134-3 226Ω* *LOW TC, STABLE ESISTO SLOPE TIM 5k 5V 5k 332k 15k LT19 11k* OTPT 1mV/ C ZEO TIM 1k 15V 1k ZEO ADJ Figure 3. Centigrade Temperature Sensor 134 F3 15V Figure 4. Centigrade Temperature Sensor with 2 Point Trim 134 F4 TYPICAL APPLICATIO S Basic 2-Terminal Current Source SET Low Output Impedance Thermometer (Kelvin Output) 4.8V 3* 6Ω 1 23Ω VOT = 1mV/ K Z OT 1Ω Zero Temperature Coefficient Current Source I + SET 134 TA2 C1.1µF 2 1k D1 1N457 1* 1 SET 134 TA3 134 TA4 *OTPT IMPEDANCE OF THE LM134 AT THE PIN IS O APPOXIMATELY Ω, WHEE O IS THE EQIVALENT 16 EXTENAL ESISTANCE CONNECTED TO THE PIN. THIS NEGATIVE ESISTANCE CAN BE EDCED BY A FACTO OF 5 O MOE BY INSETING AN EQIVALENT ESISTO IN SEIES WITH THE OTPT. *SELECT ATIO OF 1 TO SET TO OBTAIN ZEO DIFT. I + 2. 7
TYPICAL APPLICATIO S Higher Output Current Low Output Impedance Thermometer Low Input Voltage eference Driver V EF + 2mV 1* C1* 2N295 SET C1.22 1 15k 2 3Ω 2N425 V OT = 1mV/ K Z OT 2Ω 3 1Ω C1.1 1 1.5k + V Z Q1 2N425 V OT = V Z + 64mV AT 25 C I OT 3mA LT19 2 12Ω TA5 4 4.5k TA7 *SELECT 1 AND C1 FO OPTIMM STABILITY TA6 Micropower Bias 1.2V egulator with 1.8V Minimum Input Zener Biasing 1.8V LM425 1µA SET 68k LM134** 1k C1.1 1 33k 2N425 V OT = 1.2V I OT 2µA 1N457** 1* 6k 2* 68Ω V Z TA1 SET V OT TA9 TA8 * SELECT ATIO OF 1 TO 2 FO ZEO TEMPEATE DIFT ** LM134 AND DIODE SHOLD BE ISOTHEMAL Alternate Trimming Technique Buffer for Photoconductive Cell High Precision Low TC Current Source 1* SET TA11 1.5V TA12 LT14-1.2 (1.235V) + 5µA 1 6.8k 2* TA13 8 *FO ±1% ADJSTMENT, SELECT SET 1% HIGH AND MAKE 1 3 SET *I 1.37V SET = + 1µA 2 TC =.16%/ C + 33nA/ C EGLATION./V
TYPICAL APPLICATIO S Precision 1nA Current Source Micropower 5V eference 15V = 6.5V TO 15V I O LM134 2 226k 3 1M 4 1MΩ 2 3 + 1 2.7k LT14-1.2 4 15V 7 LT18 8 6 BFFEED VOLTAGE OTPT 2pF LT14-1.2 (1.235V) 1M 5.6k 3 2 + 7 LM425 4 22M 6 8 15pF V OT = 5V 3.1M TA15 I O = 1nA Z O 1 12 Ω 15V COMPLIANCE = 14V TO 12.5V TA14 FET Cascoding for Low Capacitance and/or ltrahigh Output Impedance Q1* SET SET Q2* *SELECT Q1 O Q2 TO ENSE AT LEAST 1V ACOSS THE LM134. V P (1 /I DSS ) 1.2V. TA16 SCHE ATIC DIAGA W W Q7 Q8 Q4 Q5 Q6 Q3 C1 5pF Q2 Q1 134 SD 9
PACKAGE DESCIPTIO H Package 2-Lead and 3-Lead TO-46 Metal Can (eference LTC DWG # 5-8-134) EFEENCE PLANE.29.219 (5.39 5.537).178.195 (4.521 4.953).5 (12.7) MIN.85.15 (2.159 2.667) *.25 (.635) MAX.5 (1.27) TYP.36.46 (.914 1.168).1 (2.54) TYP PIN 1 45.5 (1.27) TYP FO 3-LEAD PACKAGE ONLY.28.48 (.711 1.219) H2/3(TO-46) 198.16.21** (.46.533) DIA * LEAD DIAMETE IS NCONTOLLED BETWEEN THE EFEENCE PLANE AND.45" BELOW THE EFEENCE PLANE.16.24 ** FO SOLDE DIP LEAD FINISH, LEAD DIAMETE IS (.46.61) OBSOLETE PACKAGE Z Package 3-Lead Plastic TO-92 (Similar to TO-226) (eference LTC DWG # 5-8-141).6 ±.5 (1.524±.127) DIA.18 ±.5 (4.572 ±.127).18 ±.5 (4.572 ±.127).9 (2.286) NOM.5 (12.7) MIN.5 NCONTOLLED (1.27) LEAD DIMENSION MAX 5 NOM.5 (1.27) BSC.16 ±.3 (.46 ±.76).6 ±.1 (1.524 ±.254).14 ±.1 (3.556 ±.127).15 ±.2 (.381 ±.51) Z3 (TO-92) 41.98 +16/.4 (2.5 +.4/.1) 2 PLCS TO-92 TAPE AND EEL EFE TO TAPE AND EEL SECTION OF LTC DATA BOOK FO ADDITIONAL INFOMATION 1 1 NOM
PACKAGE DESCIPTIO S8 Package 8-Lead Plastic Small Outline (Narrow.15 Inch) (eference LTC DWG # 5-8-161).189.197* (4.81 5.4) 8 7 6 5.228.244 (5.791 6.197).15.157** (3.81 3.988) SO8 1298 1 2 3 4.8.1 (.23.254).1.2 (.254.58) 45 8 TYP.53.69 (1.346 1.752).4.1 (.11.254).16.5 (.46 1.27) * DIMENSION DOES NOT INCLDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED.6" (.152mm) PE SIDE ** DIMENSION DOES NOT INCLDE INTELEAD FLASH. INTELEAD FLASH SHALL NOT EXCEED.1" (.254mm) PE SIDE.14.19 (.355.483) TYP.5 (1.27) BSC Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11
TYPICAL APPLICATIO S In-Line Current Limiter Generating Negative Output Impedance SET C1* 1* OP AMP SET *SE MINIMM VALE EQIED TO ENSE STABILITY OF POTECTED DEVICE. THIS MINIMIZES INSH CENT TO A DIECT SHOT. TA17 TA18 *Z OT 16 1(1/ MST NOT EXCEED ). Ground eferred Fahrenheit Thermometer 3V 4 56k C1.1 2N425 1 8.25k 3* V OT = 1mV/ F 1 F T 25 F 5** 2 1Ω LT19 2.5V* *SELECT 3 = V EF /583µA **SELECT FO 1.2mA TA19 12 134sc LT/CP 11 1.5K EV C PINTED IN SA Linear Technology Corporation 163 McCarthy Blvd., Milpitas, CA 9535-7417 (48) 432-19 FAX: (48) 434-57 www.linear.com LINEA TECHNOLOGY COPOATION 1991