Solid-sae Muli-funcional Timers CSM DS_E_6_ Muliple Operaing Modes and Muliple Time Ranges. DIN 48 x 48-mm Mulifuncional Timer wih Wide AC/DC Supply Range for Boh High and Low Volages. A wide AC/DC power range grealy reduces he number of imer models kep in sock. A wide range of applicaions wih muliple operaing modes, six modes for 11-pin models and four modes for 8-pin models. Ecological design wih reduced curren consumpion. Easy sequence checking wih insananeous oupus for a zero se value. Lengh of 80 mm or less when panel-mouned wih a P3GA-11 Socke (8E, 0 o 40 VAC, 0 o 15 VDC) PNP inpu models available. Sandards: UL, CSA, NK, LR, EN 6181-1, and CE Marking. LR Model Number Srucure Model Number Legend Noe: This model number legend includes combinaions ha are no available. Before ordering, please check he Lis of Models on page for availabiliy. @ @ @ - @ @ 1 3 4 5 1. Number of Pins None: 11-pin models 8: 8-pin models. Inpu Type for 11-pin Models None: No-volage inpu (NPN ype) P: Volage inpu (PNP ype) 3. Oupu None: Relay oupu (DPDT) S: Transisor oupu (NPN/PNP universal use) E: Relay oupu (SPDT) wih insananeous relay oupu (SPDT) 4. Suffix 300: Dual mode models (signal ON/OFF-delay and one-sho) 301: Double ime scale (range) models (0.1 s o 600 h) 5. Supply Volage 0-40AC/0-15DC: 0 o 40 VAC/0 o 15 VDC 4-48AC/1-48DC: 4 o 48 VAC/1 o 48 VDC 4-48AC/DC: 4 o 48 VAC/VDC (Only for 8E) 1
Ordering Informaion Lis of Models Noe: 1. Specify boh he model number and volage when ordering. Example: 0-40AC/0-15DC 11-pin Models Conac 8-pin Models Supply volage. The operaing modes are as follows A: ON-delay D: Signal OFF-delay B: Flicker OFF sar E: Inerval B: Flicker ON sar G: Signal ON/OFF-delay C: Signal ON/OFF-delay J: One-sho Transisor (Phoocoupler) Conac Transisor (Phoocoupler) Oupu Supply volage Inpu ype Time range Operaing mode (See noe ) 0 o 40 VAC (50/60 Hz)/ 0 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 0 o 40 VAC (50/60 Hz)/ 0 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 0 o 40 VAC (50/60 Hz)/ 0 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 0 o 40 VAC (50/60 Hz)/ 0 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC No-volage inpu 0.05 s o 300 h Six muli-modes: A, B, B, C, D, E Dual-modes: G, J Volage inpu Six muli-modes: A, B, B, C, D, E Model (See noe 1.) -300 P No-volage inpu 0.1 s o 600 h -301 0.05 s o 300 h S Oupu Supply volage Inpu ype Time range Operaing mode (See noe ) Time-limi conac and insananeous conac 0 o 40 VAC (50/60 Hz)/ 0 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 0 o 40 VAC (50/60 Hz)/ 0 o 15 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 4 o 48 VAC (50/60 Hz)/ 1 o 48 VDC 0 o 40 VAC (50/60 Hz)/ 0 o 15 VDC 4 o 48 VAC/VDC (50/60 Hz) No-inpu available 0.05 s o 300 h Four muli-modes: A, B, E, J ( sar) Model (See noe 1.) 8 0.1 s o 600 h 8-301 0.05 s o 300 h 8S 8E
Accessories (Order Separaely) Adaper, Proecive Cover, Hold down Clip, Seing Ring and Panel Cover Name/specificaions Flush Mouning Adaper Y9F-30 Y9F-73 Y9F-74 Proecive Cover Y9A-48B Hold-down Clip (Sold in ses of For PF085A Socke Y9H-8 wo) For PL08 and PL11 Sockes Y9H-7 Seing Ring A Y9S-7 Seing Ring B and C Y9S-8 Panel Cover Ligh gray (5Y7/1) Y9P-48GL Black (N1.5) Y9P-48GB Medium gray (5Y5/1) Y9P-48GM Models Sockes Timer Round Sockes Pin Connecion Terminal Models 11-pin Fron Connecing DIN rack mouning PCF-11 DIN rack mouning PCF-11-E (Finger-safe ype) Back Connecing Screw erminal P3GA-11 Solder erminal PL11 Wrapping erminal PL11-Q PCB erminal PLE11-0 8-pin Fron Connecing DIN rack mouning PCF-08 DIN rack mouning PCF-08-E (Finger-safe ype) DIN rack mouning PF085A Back Connecing Screw erminal P3G-08 Solder erminal PL08 Wrapping erminal PL08-Q PCB erminal PLE08-0 Noe: 1. The PCF-@@-E has a finger-proecion srucure. Round crimp erminals canno be used. Use forked crimp erminals.. The P3GA-11 and P3G-08 Socke can be used ogeher wih he Y9A-48G Terminal Cover o implemen finger proecion. 3. For deails, refer o Socke and DIN Track Producs. Terminal Cover Applicaion Model Remarks For back connecing socke Y9A-48G For P3G-08 and P3GA-11 Noe: For deails, refer o Socke and DIN Track Producs. 3
Specificaions General Iem /-AS P 8/-A8S 8E Operaing mode A: ON-delay B: Flicker OFF sar B: Flicker ON sar C: Signal ON/OFF-delay D: Signal OFF-delay E: Inerval G: Signal ON/OFF-delay (Only for -300) J: One-sho (Only for -300) *The inernal circuis are opically isolaed from he oupu. This enables universal applicaion as NPN or PNP ransisor. Time Ranges Noe: When he ime seing knob is urned below 0 unil he poin where he ime seing knob sops, he oupu will operae insananeously a all ime range seings. Sandard (0.05-s o 300-h) Models Double (0.1-s o 600-h) Models A: ON-delay (power sar) B: Flicker ON sar (power sar) E: Inerval (power sar) J: One-sho (power sar) Pin ype 11-pin 8-pin Inpu ype No-volage inpu Volage inpu --- Time-limi oupu ype /-A8/-AP: Relay oupu (DPDT) S/-A8S: Transisor oupu (NPN/PNP universal)* Insananeous oupu ype --- Mouning mehod DIN rack mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C. No.14, NK, Lloyds Conforms o EN6181-1 and IEC60664-1 (VDE01) 4kV/. Oupu caegory according o EN60947-5-1 for Timers wih Conac Oupus. Oupu caegory according o EN60947-5- for Timers wih Transisor Oupus. Relay oupu (SPDT) Relay oupu (SPDT) Time uni s (sec) min (min) h (hrs) h ( hrs) Full scale 1. 0.05 o 1. 0.1 o 1. 1. o 1 seing 3 0.3 o 3 3 o 30 1 1. o 1 1 o 30 3 o 30 30 o 300 Time uni s (sec) min (min) h (hrs) h ( hrs) Full scale.4 0.1 o.4 0.4 o.4.4 o 4 seing 6 0.6 o 6 6 o 60 4.4 o 4 4 o 40 60 6 o 60 60 o 600 4
Raings Raed volage (See noes 1,, and 5.) 0 o 40 VAC (50/60 Hz)/0 o 15 VDC, 4 o 48 VAC (50/60 Hz)/1 o 48 VDC (4 o 48 VAC/VDC for H3CR- A8E) (See noe3.) Operaing volage range 85% o 1% of raed volage (90% o 1% a 1 VDC) rese Minimum power-opening ime: 0.1 s Inpu No-volage Inpu ON impedance: 1 kω max. ON residual volage: 1 V max. OFF impedance: 0 kω min. Volage Inpu Max. permissible capaciance beween inpus lines (erminals 6 and 7): 1,00 pf Load connecable in parallel wih inpus (erminals 6 and 7). 0 o 40 VAC/0 o 15 VDC High (logic) level: 85 o 64 VAC/85 o 137.5 VDC Low (logic) level: 0 o VAC/0 o VDC 4 o 48 VAC/1 o 48 VDC High (logic) level: 0.4 o 5.8 VAC/.8 o 5.8 VDC Low (logic) level: 0 o.4 VAC/0 o 1. VDC consumpion /-A8 0 o 40 VAC/0 o 15 VDC (When a 40 VAC, 60 Hz) Relay ON: approx..0 VA (1.6 W) Relay OFF: approx. 1.3 VA (1.1 W) 4 o 48 VAC/1 o 48 VDC (When a 4 VDC) Relay ON: approx. 0.8 W Relay OFF: approx. 0. W P (See noe 3) 0 o 40 VAC/0 o 15 VDC (When a 40 VAC, 60 Hz) Relay ON: approx..5 VA (. W) (See noe 4.) Relay OFF: approx. 1.8 VA (1.7 W) (See noe 4.) 4 o 48 VAC/1 o 48 VDC (When a 4 VDC) Relay ON: approx. 0.9 W (See noe 4.) Relay OFF: approx. 0.3 W (See noe 4.) 8E 0 o 40 VAC/0 o 15 VDC (When a 40 VAC, 60 Hz) Relay ON/OFF: approx. VA (0.9 W) 4 o 48 VAC/VDC (When a 4 VDC) Relay ON/OFF: approx. 0.9 W S/-A8S 4 o 48 VAC/1 o 48 VDC (When a 4 VDC) Oupu ON: 0.3 W Oupu OFF: 0. W Conrol oupus Time limi conacs: 5 A a 50 VAC/30 VDC, 0.15 A a 15 VDC, resisive load (cosφ = 1) Transisor oupu: Open collecor (NPN/PNP), 0 ma max. a 30 VDC max., residual volage: V max. Insananeous conac: 5 A a 50 VAC/30 VDC, 0.15 A a 15 VDC, resisive load (cosφ = 1) Noe: 1. DC ripple rae: 0% max. (A single-phase, full-wave-recificaion power can be used).. Do no use an inverer oupu as he power. Refer o Safey Precauions for All Timers for deails. 3. Models wih 4-o-48-VAC or 1-o-48-VDC power have inrush curren. Cauion is hus required when urning ON and OFF power o he Timer wih a non-conac oupu from a device such as a sensor. (Models wih an inrush curren of approximaely 50 ma and a 4- VDC power are available (he -30 and 8-30).) 4. The values are for when he erminals and 7 and erminals and 6 are shor-circuied, and include he consumpion curren of he inpu circui. 5. Refer o Safey Precauions for All Timers when using he Timer ogeher wih a -wire AC proximiy sensor. 5
Characerisics Noe: 1. The value is ±5% FS +0 ms o 0 ms max. when he C, D, or G mode signal of he P is OFF.. Refer o he Life-es Curve. 3. Relay oupu only. Life-es Curve Accuracy of operaing ±0.% FS max. (±0.%± ms max. in a range of 1. s or 3 s) ime Seing error ±5% FS ±50 ms (See noe 1) Rese ime Min. power-opening ime: 0.1 s max. Min. pulse widh: 0.05 s (/-AS) Rese volage % max. of raed volage Influence of volage ±0.% FS max. (±0.%± ms max. in a range of 1. s or 3 s) Influence of emperaure ±1% FS max. (±1%± ms max. in a range of 1. s or 3 s) Insulaion resisance 0 MΩ min. (a 500 VDC) Dielecric srengh,000 VAC (1,000 VAC for @S), 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed noncurren-carrying meal pars),000 VAC (1,000 VAC for @S), 50/60 Hz for 1 min (beween conrol oupu erminals and operaing circui),000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher),000 VAC, 50/60 Hz for 1 min (beween inpu and conrol oupu erminals and operaion circui) for P Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance 3 kv (beween power erminals) for 0 o 40 VAC/0 o 15 VDC, 1 kv for 4 o 48 VAC/1 o 48 VDC 4.5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) for 0 o 40 VAC/0 o 15 VDC, 1.5 kv for 4 o 48 VAC/1 o 48 VDC and 4 o 48 VAC/VDC ±1.5 kv (beween power erminals) and ±600 V (beween no-volage inpu erminals), square-wave noise by noise simulaor (pulse widh: 0 ns/1 μs, 1-ns rise) Malfuncion: 8 kv Desrucion: 15 kv Desrucion: o 55 Hz wih 0.75-mm single ampliude each in 3 direcions for hours each Malfuncion: o 55 Hz wih 0.5-mm single ampliude each in 3 direcions for minues each Desrucion: 1,000 m/s 3 imes each in 6 direcions Malfuncion: 0 m/s 3 imes each in 6 direcions Ambien emperaure Operaing: C o 55 C (wih no icing) Sorage: 5 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 0,000,000 operaions min. (under no load a 1,800 operaions/h) Elecrical: 0,000 operaions min. (5 A a 50 VAC, resisive load a 1,800 operaions/h) (See noe ) EMC (EMI) EN6181-1 Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN6181-1 Immuniy ESD: IEC600-4-: 6 kv conac discharge (level 3) 8 kv air discharge (level 3) Immuniy RF-inerference from AM Radio Waves: IEC600-4-3: V/m (80 MHz o 1 GHz) (level 3) Immuniy RF-inerference from Pulse-modulaed Radio Waves:IEC600-4-3: V/m (900±5 MHz) (level 3) Immuniy Conduced Disurbance: IEC600-4-6: V (0.15 o 80 MHz) (level 3) Immuniy Burs: IEC600-4-4: kv power-line (level 3) kv I/O signal-line (level 4) Immuniy Surge: IEC600-4-5: 1 kv line o line (level 3) kv line o ground (level 3) Case color Ligh gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh Approx. 90 g,000 Swiching operaions (x 3 ) 5,000 1,000 500 0 30 VDC L/R = 7 ms 50 VAC (cosφ = 0.4) 50 VAC/30 VDC (cosφ = 1) Reference: A maximum curren of 0.15 A can be swiched a 15 VDC (cosφ = 1) and a maximum curren of 0.1 A can be swiched if L/R is 7 ms. In boh cases, a life of 0,000 operaions can be expeced. The minimum applicable load is ma a 5 VDC (failure level: P). Load curren (A) 6
Connecions Block Diagrams /AS AC (DC) inpu Zero seing deecion circui Time range/ uni selecors Operaing mode selecor circui Oscillaion circui Couning circui Oupu circui Rese inpu, sar inpu, and gae inpu Inpu circui Indicaor circui -ON indicaor Oupu-ON indicaor P AC (DC) inpu Zero seing deecion circui Time range/ uni selecors Operaing mode selecor circui Oscillaion circui Couning circui Oupu circui Sar Inpu circui Indicaor circui -ON indicaor Oupu-ON indicaor 7
8/A8S AC (DC) inpu Zero seing deecion circui Time range/ uni selecors Operaing mode selecor circui Oscillaion circui Couning circui Oupu circui Indicaor circui -ON indicaor Oupu-ON indicaor 8E AC (DC) inpu Zero seing deecion circui Time range/ uni selecors Operaing mode selecor circui Oscillaion circui Couning circui Oupu circui Indicaor circui -ON indicaor Oupu-ON indicaor Insananeous oupu circui I/O Funcions Inpus (for -A/ -AS models) Sar Rese Noe: P incorporaes sar inpu only. Sars ime-measuremen. Inerrups ime-measuremen and reses ime-measuremen value. No ime-measuremen is made and conrol oupu is OFF while he rese inpu is ON. Gae Prohibis ime-measuremen. Oupus Conrol oupu Oupus are urned ON according o designaed oupu mode when prese value is reached. 8
Terminal Arrangemen Noe: The delayed conac of convenional Timers was indicaed as The conac symbol of he is indicaed as 11-pin Models /-A-300/-A-301 (Conac Oupu) because is operaing mode is six muli-modes (four muli-modes for he 8). 8-pin Models 8/-A8-301 (Conac Oupu) Rese inpu Sar inpu Gae inpu 8S (Transisor Oupu) S (Transisor Oupu) Rese inpu Sar inpu Gae inpu Noe: Terminals 1, 3, 4, and 5 are empy. Terminals and 7 are he same as for he 8. 8E (Conac Oupu) Noe: Terminals 1, 3, 4, and 8 are empy. Terminals, 5, 6, 7, and are he same as for he. P (Conac Oupu) Sar inpu Noe: 1. Terminal 5 is empy.. Separae power supplies can be used for he Timer and inpus. 9
Inpu Connecions /-AS The inpus of he /-AS are no-volage (shor-circui or open) inpus. No-volage Inpus No-conac Inpu Conac Inpu No-conac Inpu (Connecion o NPN open collecor oupu sensor.) 1 o 4 VDC (sensor power ) + DC power (Connecion o a volage oupu sensor.) 1 o 4 VDC (sensor power ) + DC power Sensor Timer 5 Gae 6 Sar 7 Rese Timer 5 Gae 6 Sar 7 Rese Sensor Timer 5 6 7 Gae Sar Rese Inpu (0 V) Inpu (0 V) Inpu (0 V) Operaes wih ransisor ON Operaes wih relay ON Operaes wih ransisor ON No-volage Inpu Signal Levels No-conac inpu Conac inpu 1. Shor-circui level Transisor ON Residual volage: 1 V max. Impedance when ON: 1 kω max.. Open level Transisor OFF Impedance when OFF: 0 kω min. Use conacs which can adequaely swich 0.1 ma a 5 V
P The sar inpu of he P is volage inpu. (Volage imposiion or open) Volage Inpus No-conac Inpu No-conac Inpu Conac Inpu (Connecion o PNP open (Connecion o NPN open collecor oupu sensor) collecor oupu sensor) 1 o 4 VDC (sensor power ) Sensor + (+) 6 Sar 7 DC power Timer Inpu 0V ( ) Sensor 1 o 4 VDC (sensor power ) + DC power (+) 6 7 Timer Sar Inpu 0V ( ) AC power DC power 6 7 Timer (+) Sar Inpu 0V ( ) Operaes wih PNP ransisor ON Operaes wih NPN ransisor ON Noe: The inpu circui is isolaed from he power circui. Thus, an NPN ransisor can be conneced. Operaes wih relay ON Noe: Refer o he signal levels in he following able and be aware of he minimum applicable load of he relay. Noe: Before making connecions, refer o Safey Precauions (H3CR-@). Volage Inpu Signal Levels No-conac inpu 1. Transisor ON Residual volage: 1 V max. The volage beween erminals 6 and 7 mus be.8 VDC min.. Transisor OFF Leakage curren: 0.01 ma max. The volage beween erminals 6 and 7 mus be 1. VDC max. Conac inpu Use conacs ha can adequaely swich 0.1 ma a each operaing volage. The volage beween erminals 6 and 7 wih conacs ON or OFF mus saisfy he specified value. Conacs ON 0-o-40-VAC and 0-o-15-VDC models: 85 o 64 VAC or 85 o 137.5 VDC 4-o-48-VAC and 1-o-48-VDC models: 0.4 o 5.8 VAC or.8 o 5.8 VDC Conacs OFF 0-o-40-VAC and 0-o-15-VDC models: 0 o VAC or 0 o VDC 4-o-48-VAC and 1-o-48-VDC models: 0 o.4 VAC or 0 o 1. VDC 11
Operaion Timing Char Noe: 1. The minimum power-opening ime ( R ) is 0.1 s.. The minimum inpu pulse widh (for sar, rese) is 0.05 s. 3. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. 4. sar in mode J is also possible for 8/-A8E/-A8S/-A8-301 models. 5. Refer o page 17 for applicaion examples. /-AS/-AP* *P model incorporaes sar inpu only. Operaing mode Timing char A: ON-delay Basic operaion Sar B: Flicker OFF sar B: Flicker ON sar C: Signal ON/ OFF-delay Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar Sar (See noe) Oupu Noe: Sar inpu is invalid while he Timer is in operaion. Basic operaion Sar (See noe) Oupu Noe: Sar inpu is invalid while he Timer is in operaion. Basic operaion Sar (See noe) Oupu Noe: Sar inpu is invalid while he Timer is in operaion. Basic operaion Rese Oupu relay (NC) Sar (See noe) Oupu Oupu relay (NO) (Oupu indicaor) indicaor Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. 1
Operaing mode D: Signal OFFdelay Sar Timing char Basic operaion Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar (See noe) Oupu Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. E: Inerval Basic operaion Sar Rese Oupu relay (NC) Sar (See noe) Oupu Oupu relay (NO) (Oupu indicaor) indicaor Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. G: Signal ON/ OFF-delay Sar Basic operaion J: One-sho oupu Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar Sar (See noe) Oupu Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. Basic operaion Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) Sar (See noe) Oupu 1±0.6 s (Fixed) Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. (Previous sar inpu will be cancelled.) Gae Signal Inpu 1 ON OFF Sar ON OFF Gae ON OFF Rese ON OFF Oupu ON relay OFF Noe: 1. This iming char indicaes he gae inpu in operaing mode A (ON-delay operaion).. The se ime is he sum of 1 and. 3. P model incorporaes sar inpu only. 13
8/-A8S Operaing mode Timing char A: ON-delay Basic operaion Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Oupu B: Flicker ON sar Basic operaion E: Inerval Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Oupu Oupu Basic operaion v J: One-sho oupu Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) Basic operaion Oupu 1±0.6 s (Fixed) Noe: 1. The minimum power-opening ime ( R ) is 0.1 s.. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. 14
8E Operaing mode A: ON-delay Oupu relay (NC) Timing char Oupu relay (NO) (oupu indicaor) Basic operaion Insananeous oupu relay (NC) Insananeous oupu relay (NO) Oupu B: Flicker ON sar indicaor Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) Basic operaion Oupu E: Inerval indicaor Oupu relay (NC) J: One-sho oupu Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) indicaor Oupu relay (NC) Basic operaion Oupu Oupu relay (NO) (oupu indicaor) (Fixed) (Fixed) Basic operaion Insananeous oupu relay (NC) Insananeous oupu relay (NO) Oupu 1±0.6 s (Fixed) indicaor Noe: 1. The minimum power-opening ime ( R ) is 0.1 s.. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. Nomenclaure indicaor (green) (Flashes when Timer operaes; li when Timer sops operaing) Operaing mode display window Oupu indicaor (orange) (Li when oupu) Time range selecor (selec one from 1., 3, 1, and 30 a full scale; wih he @-301, selec from.4, 6, 4, or 60 a full scale.) Time seing knob (se ime) Operaing mode selecor Selec a mode from: A, B, B, C, D, and E (, -AP, and -AS) A, B, E and J (8, -A8S, and -A8E) G and J (-300) Scale range display windows Time uni display window Time uni selecor (selec one from sec, min, hrs, and h) 15
Dimensions Noe: All unis are in millimeers unless oherwise indicaed. P S 48 15 6 66.6 5.3 0.7 48 39 dia. 44.8 44.8 11 pins 8 8S 8E 48 15 66.6 6 5.3 0.7 48 39 dia. 44.8 44.8 8 pins Dimensions wih Se Ring 50 16.5 50 4 dia. Dimensions wih Fron Connecing Socke PCF-08-@/PCF-11-@ Time Seing Ring Panel cover Dimensions wih Back Connecing Socke P3G-08/P3GA-11 81.5 81.5 15 15 80 75 0.8* S P 98.5 PCF-11 PCF-11-E.3* 8@ 89.9* 87.6 PCF-08 PCF-08-E.3* S P + Adaper 8@ + Adaper Y9F-30 P3GA-11 Y9F-30 P3G-08 (When (When Y9A-48G Y9A-48G mouned) mouned) *These dimensions vary wih he kind of DIN rack (reference value). 16
Applicaion Examples () A Mode: ON-delay ON-delay operaion (A mode) is a basic mode. 1. -ON Sar/-OFF Rese The -ON sar/-off rese operaion is a sandard operaing mehod. ( and ) Sar ( and 6) Rese ( and 7) 3. Conrol of Inegraed Time wih Gae Signal Wih a gae signal, he -ON sar operaion and Signal sar operaion can be conrolled (he operaion can be inerruped). ( and ) Sar ( and 6) 1 1 + : se ime Conrol oupu: NC (8 and 11) NC (1 and 4) Gae ( and 5) Conrol oupu: NO (9 and 11) NO (1 and 3) Conrol oupu: NC (8 and 11) NC (1 and 4) indicaor Exernally shor-circuied Flashing Li Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Gae signal (The operaion is inerruped wih he gae signal if he Timer deecs an abnormal signal.) Li. Signal Sar/Signal Rese The Signal sar/signal rese operaion is useful for remoe conrol of he Timer. ( and ) Sar ( and 6) Rese ( and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Sar signal (remoe conrol possible) Rese signal (remoe conrol possible) Li Exernally shor-circuied B/B Mode: Flicker The flicker operaion in he B and B modes can be effecively applied o lamp or buzzer (ON and OFF) alarms or he monioring of an inermien operaion wih a display. 1. -ON Sar/-OFF Rese (in B Mode) ( and ) Sar ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Exernally shor-circuied ( coninuously supplied) 17
. Signal Sar/Signal Rese (in B Mode) If here is an abnormal signal, flashing sars. When he abnormal condiion is resored, a rese signal sops he display flashing. ( and ) Sar ( and 6) Rese ( and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Sar signal Rese signal. Signal-ON-OFF Sar/Insananeous Operaion/Time-limi Rese ( and ) Sar ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Flashing Li Flashing Li Sar signal (The operaion sars wih he signal ON or OFF) ( coninuously supplied) C Mode: Signal ON/OFF-delay The Signal ON-/OFF-delay operaion (C mode) is useful for he conrol of disribuion of producs on a producion line ino boxes by he specified number or ime. 1. -ON Sar/Insananeous Operaion/ Time-limi Rese A se of hese funcions is useful for he operaion of a machine for a specified period when power is ON. D Mode: Signal OFF-delay Signal OFF-delay operaion (D mode) can be effecively used o keep a load operaing for a cerain period. For example, his funcion enables he cooling fan for a lamp or heaer o operae for a cerain period afer he lamp or heaer is swiched OFF. 1. -ON Sar/Insananeous Operaion/ Time-limi Rese ( and ) ( coninuously supplied) Sar ( and 6) ( and ) Sar ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li indicaor Flashing Li Flashing Li Sar signal (NC o NO) Exernally shor-circuied 18
. Signal Sar/Insananeous Operaion/ Time-limi Rese ( and ). Signal Sar/Insananeous Operaion/ Time-limi Rese This funcion is useful for he repeiive conrol such as he filling of liquid for a specified period afer each Signal sar inpu. Sar ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor ( and ) Sar ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Li Flashing Li Conrol oupu: NO (9 and 11) NO (1 and 3) Sar signal (NO o NC o NO) indicaor Sar signal Flashing Li Flashing Li E Mode: Inerval ( coninuously supplied) 1. -ON Sar/Insananeous Operaion/ Time-limi Rese This funcion is useful for he operaion of a machine for a specified period afer power is ON. ( coninuously supplied) ( and ) Sar ( and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Li Flashing Li Exernally shor-circuied 19
Safey Precauions () Refer o Safey Precauions for All Timers. Noe: The following precauions apply o all models. Supplies For he power of an inpu device of he @/-A@S/-AP, use an isolaing ransformer wih he primary and secondary windings muually isolaed and he secondary winding no grounded. Correc G, S, R 5, 6, 7 Inpu erminal Inpu/Oupu Relaionship beween Inpu and Supply Circuis (excep for 8E) The (excep for 8E) uses ransformerless power. When connecing a relay or ransisor as an exernal signal inpu device, pay aenion o he following poins o preven shorcircuiing due o a sneak curren o he ransformerless power. If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no differ in phase, oherwise he erminals will be shor-circuied o one anoher. Incorrec Conac or ransisor for exernal inpu signal Shor-circui curren Inpu device Isolaion ransformer is required. Inpu erminal Incorrec G, S, R 5, 6, 7 Inpu erminal Inpu erminal Correc Inpu erminal Inpu device Isolaion ransformer The @/-A@S/AP s power erminal is a common erminal for inpu signals o he Timer. Do no disconnec he wires on erminal, oherwise he inernal circuiry of he Timer will be damaged. Inpu erminal 5, 6, 7 G, S, R Inpu erminal I is impossible o provide wo independen power swiches as shown below regardless of wheher or no he Timers are differen in phase. Inpu erminal Make sure ha he volage is applied wihin he specified range, oherwise he inernal elemens of he Timer may be damaged. Inpu erminal 0
Relaionship beween Inpu and Supply Circuis (@/-A@S) An appropriae inpu is applied o he inpu signal erminals of he @/-A@S when one of he inpu erminals is shor-circuied wih he common erminal (erminal ) for he inpu signals. Never use erminal as he common erminal for his purpose, oherwise he inernal circui of he Timer will be damaged. Incorrec If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no be differen in phase or he erminals will be shor-circuied o one anoher (refer o he figures below). Incorrec Conac or ransisor for exernal inpu signal 6 7 P AC or DC power 5, 6, 7 G, S, R Inpu erminal 6 7 P Shor-circui curren Correc AC or DC power 5, 6, 7 G, S, R Inpu erminal Correc Conac or ransisor for exernal inpu signal 6 7 P Do no connec a relay or any oher load beween inpu erminals, oherwise he inernal circui of he Timer will be damaged due o he high-ension volage applied o he inpu erminals. 6 Shor-circui curren Ry 7 P AC or DC power Inpu conac 5, 6, 7 G, S, R Inpu erminal Relaionship beween Inpu and Supply Circuis (P) Common o All Models Wih he P, inpu wires mus be as shor as possible. If he floaing capaciy of wires exceeds 1,00 pf (approx. m for cables wih pf/m), he operaion will be affeced. Pay paricular aenion when using shielded cables. The @S ransisor oupu is isolaed from he inernal circuiry by a phoocoupler. Therefore, eiher NPN or PNP oupu is possible. P AC/DC power Inpu circui circui Since he inpu circui and he power circui are configured independenly, he inpu circui can be urned ON or OFF irrespecive of he ON/OFF sae of he power. I mus be noed ha a volage equivalen o he power volage is applied o he inpu circui. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To conver millimeers ino inches, muliply by 0.03937. To conver grams ino ounces, muliply by 0.0357. In he ineres of produc improvemen, specificaions are subjec o change wihou noice. 1
Read and Undersand This Caalog Please read and undersand his caalog before purchasing he producs. Please consul your OMRON represenaive if you have any quesions or commens. Warrany and Limiaions of Liabiliy WARRANTY OMRON's exclusive warrany is ha he producs are free from defecs in maerials and workmanship for a period of one year (or oher period if specified) from dae of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no even shall he responsibiliy of OMRON for any ac exceed he individual price of he produc on which liabiliy is assered. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Applicaion Consideraions SUITABILITY FOR USE OMRON shall no be responsible for conformiy wih any sandards, codes, or regulaions ha apply o he combinaion of producs in he cusomer's applicaion or use of he producs. A he cusomer's reques, OMRON will provide applicable hird pary cerificaion documens idenifying raings and limiaions of use ha apply o he producs. This informaion by iself is no sufficien for a complee deerminaion of he suiabiliy of he producs in combinaion wih he end produc, machine, sysem, or oher applicaion or use. The following are some examples of applicaions for which paricular aenion mus be given. This is no inended o be an exhausive lis of all possible uses of he producs, nor is i inended o imply ha he uses lised may be suiable for he producs: Oudoor use, uses involving poenial chemical conaminaion or elecrical inerference, or condiions or uses no described in his caalog. Nuclear energy conrol sysems, combusion sysems, railroad sysems, aviaion sysems, medical equipmen, amusemen machines, vehicles, safey equipmen, and insallaions subjec o separae indusry or governmen regulaions. Sysems, machines, and equipmen ha could presen a risk o life or propery. Please know and observe all prohibiions of use applicable o he producs. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall no be responsible for he user's programming of a programmable produc, or any consequence hereof. Disclaimers CHANGE IN SPECIFICATIONS Produc specificaions and accessories may be changed a any ime based on improvemens and oher reasons. I is our pracice o change model numbers when published raings or feaures are changed, or when significan consrucion changes are made. However, some specificaions of he producs may be changed wihou any noice. When in doub, special model numbers may be assigned o fix or esablish key specificaions for your applicaion on your reques. Please consul wih your OMRON represenaive a any ime o confirm acual specificaions of purchased producs. DIMENSIONS AND WEIGHTS Dimensions and weighs are nominal and are no o be used for manufacuring purposes, even when olerances are shown. PERFORMANCE DATA Performance daa given in his caalog is provided as a guide for he user in deermining suiabiliy and does no consiue a warrany. I may represen he resul of OMRON s es condiions, and he users mus correlae i o acual applicaion requiremens. Acual performance is subjec o he OMRON Warrany and Limiaions of Liabiliy. ERRORS AND OMISSIONS The informaion in his documen has been carefully checked and is believed o be accurae; however, no responsibiliy is assumed for clerical, ypographical, or proofreading errors, or omissions. OMRON Corporaion Indusrial Auomaion Company hp://www.ia.omron.com/ 0.1 In he ineres of produc improvemen, specificaions are subjec o change wihou noice. (c)copyrigh OMRON Corporaion 0 All Righ Reserved.