1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness, 48 2 LED extension harnesses, 12 1 harness crimp kit 8 mounting brackets PN 1200669 Please efer r to webiste for full warranty information. DIGI-TAILS is not a licensed Mopar product.
1969 DODGE CORONET LED PANEL INSTALLATION 2 The LED boards are shipped with the slide switch set to sequential mode. We recommend that all slide switches be set to the same setting (either standard or sequential). SEQUENTIAL POSITION STANDARD POSITION Please follow all local laws concerning exterior lighting. Shown in sequential mode Hint You may begin with the LED panel installation, however, you will need to complete the wiring modifications before the LED panels and housings are paired as one. Read over the entire instruction guide to determine the method that works best for you. LED PANEL INSTALLATION 1. Cut off the power to your car. Open the hood of your car. Disconnect the negative terminal from the battery, which will cut off the power in your car. To verify that the power is disconnected, press the brake pedal; your brake lights should not turn on. 2. Remove the current taillights. Turn the light sockets counter-clockwise to remove them from the taillight housings. As a safety precaution, remove the bulbs from the sockets. Put them aside since they will no longer be needed. Remove the taillight housing assembly from rhe car. 3. Position the LED panels. Each LED panel is marked Driver Side and Passenger Side on the backside of the LED panel, which identifies where each respective LED panel is to be mounted. The Driver Side LED panel is shown above.
1969 DODGE CORONET LED PANEL INSTALLATION 3 4. Attach mounting brackets. Each light pocket on the taillight housing needs to be marked for placement of the right angle brackets. To do this, first have the housing right side up, Then from the edge of the housing measure back 1/4 and mark a parallel line. Now flip the housing upside down. Then from the edge of the housing measure 3/8 and mark a parallel line. The face of all brackets should be flush to these lines. Remove the protective tape and carefully position each bracket into place. Each housing uses four brackets. The LOWER brackets are to be marked 1/4 from the edge The UPPER brackets are to be marked 3/8 from the ledge. Housing right side up, measure 1/4 from edge for the LOWER brackets. Flip the housing around, and measure 3/8 from edge for the UPPER brackets. 5. Plug in extension harnesses. Feed the extension harness through the socket hole and plug them onto the LED panels. Using these extension harnesses allows for easy removal of the tail light assembly in the future if needed.
1969 DODGE CORONET LED PANEL INSTALLATION 4 6. Mount the LED panels. Test fit the LED panels into place before they are permanently attached to the brackets. Be certain that the LED panels are parallel with the housing edge then peel off the remaining protective tape and affix the LED panels. The correct orientation for the LED panel is to have the arrows on the LED panel pointing towards the outside, opposite of the reverse light socket.
1969 DODGE CORONET WIRE SPLICING INSTALLATION 5 WIRE SPLICING INSTALLATION 1. Review the wiring diagrams found on the last page. Each LED panel needs five connections. Listed are the LED harness colors and their respective function. : Depending on make and harness, colors may not match. ORANGE BLACK YELLOW GREEN BROWN - Constant 12 volt power source. - Grounded to body. - Running/parking light signal. - Driver side turn signal. - Passenger side turn signal. 2. Find and access the taillight wires. Pick a point in the rear body panel between the driver s side quarter panel and the driver s side taillight housing assembly and remove the cloth tape to expose the taillight wires. 3. Splice the LED SIGNAL wires into the stock SIGNAL wires. Match the LED harness to the corresponding stock harness as shown below. LED Harness Function Stock harness s Brown Passenger side turn signal Brown The light socket ends on the car harness can be removed. Green Driver side turn signal Green The light socket ends on the car harness can be removed. Yellow Running/Park signal Black Running light wires. THIS IS NOT THE CAR S GROUND. Orange Black Constant 12 volt Ground Find power at fuse panel/trunk light/dome light/fused battery feed. Ground to Body/chassis 4. Connect all the ground wires. Connect all the ground wires together. Bolt them to the trunk latch support along with the original rear body harness ground. The ground connection must be good in order to the operate the LED tail lights.
supplied with a constant 12 volt battery supply for the LED circuitry to ope the T-Tap. The other end of the orange wire is splice Take the LED harness YELLOW wires and splice them in with the original BLACK running Take the The LED T-Tap harness connector BROWN wires and light wires. is used splice it The ends to with going splice the original BROWN wires. to the to side the marker constant lights must power be included source, in the like splice the for The last page is a wire diagram of how the LED harn the side markers to remain functional. The light socket ends on the car harness are no longer needed. 1969 DODGE CORONET WIRE SPLICING INSTALLATION 6 Spice the T-Tap connector into the constant power wire, then plug the oran the T-Tap. The other end of the orange wire is spliced into the LED harness Take the ground wires and connect them all together. Bolt them to the trunk latch Take the LED harness YELLOW wires and splice them in with the original BLACK running 5. Supply the LED panel harnesses with a constant support along 12 volt with the original rear body harness ground. 1. Insert wire light wires. The ends going to the side marker lights must be included in the splice for feed using the included the side Orange markers power to remain wire functional. and T-Tap. : A good ground connection is essential to the operation of the LED tail lights. The last page is a wire diagram of how the LED harness splices into the car s Take the ground wires and connect An ORANGE them power all together. wire is Bolt supplied them along to the with trunk a T-Tap. latch The orange power wire must be An Orange power wire support is supplied along with along the with original supplied a T-Tap. rear body with The harness a constant ground. 12 Insert volt battery wire supply onto T-Tap for the LED circuitry Crimp to operate with properly. pliers orange power wire must powered with a constant The T-Tap 12 connector volt is used to splice to the constant power source, like the dome light w : A good ground connection is essential to the operation of the LED tail lights. 2. Crimp with battery supply for the LED circuitry to operate properly. You Spice the T-Tap connector into the constant To power keep wire, the wires then pliers plug neatly the orange tucked wire and into in l can use the included An T-Tap ORANGE connector power wire to is splice supplied along with a T-Tap. The orange power wire must be the T-Tap. to a constant The other end of the orange wire them is spliced over into one the LED side harness and tape Orange them wires. in power source, like the supplied dome with light, a constant trunk light, 12 volt fuse battery box, supply etc. for the LED circuitry to operate properly. The T-Tap connector is used to splice to the constant power source, like wiring the dome into light loom wire. or have the ability to w The last page is a wire diagram of how the LED harness splices into the car s original harn Spice the T-Tap connector Spice the over T-Tap the connector constant into power the constant source, power wire, then plug the orange wire into Plug then plug the orange the wire T-Tap. into Insert The the other T-Tap. wire end of onto The the other orange T-Tapend wire is ofspliced into the Crimp LED harness with Orange plierswires. the orange power wire is tied in with the orange wires of The last page is a wire diagram of how the LED harness splices Wires into spliced the car s together. 3. Plug original harness. Fold connector wires over to a side. all the LED panel harnesses. To keep the wires neatly tucked and in line, take the Plug spliced connector Insert wire onto T-Tap Crimp with pliers! sec them over to one side and tape them in place. This will allow y wiring into loom or have the ability to wrap the LED harness w To keep the wires neatly tucked and in line, take the spliced sections and fold them over to one side and tape them in place. This will allow you to place th Plug connector 6. Tuck and secure the spliced Insert wire onto wires. T-Tap Crimp with pliers 1. Fold wires to Take the spliced sections and To fold keep them wires over neatly to one tucked side and in line, take the spliced sections and fold one side. and tape them in place. This will them allow over to you one side Wires place and tape spliced the them in place. This will allow you to place the Wires wiring spliced into loom together. or have the ability together. to Fold wrap the wires Fold LED wires harness over to wiring a side. tightly away. Wrap with Wrap tape with to hold tape in placet wiring into loom or wrap the LED panel wiring tightly away.! 2. Secure with! electrical tape. Wires spliced together. Fold wires over to a side. Wrap with tape to hold in place.! A wire diagram of the LED panel s harness spliced into the car s stock harness is on the last page. 7. Place the grommet around the wires and replace the lens. Place the grommet around the panel wires and press it into the light socket hole. Test the lights to ensure correct function, then place the lens back onto the housing. The LED light kits are designed for best performance when use an electronic no-load flasher. Shown here is an optional electronic no load flasher available from DIGI-TAILS, ( PN 20-F2 ) If you decide to use a stock bi-metal flasher, we recommend a standard-duty flasher instead of a heavy-duty flasher. If your turn signal circuit includes front and rear LED turn signals, the circuit will not have enough resistance load to operate a heavy-duty bi-metal flasher, so the no-load flasher will be required for both the turn signal and emergency flashers.
1969 DODGE CORONET WIRE SPLICING INSTALLATION 7 STOCK HARNESS COLORS. BROWN: GREEN: BLACK STOCK REAR BODY HARNESS PASSENGER SIDE TURN SIGNAL DRIVER SIDE TURN SIGNAL RUNNING LIGHTS ALTHOUGH CLOSED END CONNECTORS ARE INCLUDED, IT IS RECOMMENDED THAT ALL SPLICED WIRES BE SOLDERED TOGETHER FOR BEST CONNECTION RELIABILITY. POWER CONNECTION CONSTANT FUSED POWER SOURCE. (AT DOME LIGHT OR FUSE PANEL) DRAWS LOW CURRENT, LESS THAN 3 AMPS. BOTH LED PANELS REQUIRE THE DRIVER AND PASSENGER SIDE SIGNALS. GROUND WIRES DRIVER SIDE LED PANEL PASSENGER SIDE LED PANEL