Van der Valk Solar Systems TRACKNG AND FXED SOLAR MOUNTNG SYSTEMS nstallation manual Solar Tracker Version 07
EN General user instructions Solar mounting systems Congratulations on buying a Van der Valk Solar Systems mounting system and on helping the environment by deciding to install solar panels. This document must be seen in addition to the installation manual and installation instructions. * The general user instructions describe general installation and safety instructions. * The installation manual shows you how to install the solar mounting system. * The installation instruction gives you specific measures of the engineered mounting system as a result of the 1-2-3 PV Planner. The instructions provided in these user instructions must be observed at all times. Read these instructions carefully and keep them in a safe place for future reference. Also follow the instructions stated in the manuals and instructions for the other system components that are a part of the overall PV system. All current structural, safety and building regulations must be observed. Van der Valk Solar Systems B.V. will never be liable for any direct and/or indirect intangible or consequential loss ensuing from or connected to the failure to observe the instructions provided in these user instructions. Safety instructions for roofs Solar mounting systems installed on roofs will be exposed to wind and snow. The building in question will be subject to a greater load as a result of the PV system. A design calculation must be used to establish whether or not the building in question will be able to withstand the extra load. Where necessary, modifications need to be made. The standards applied (if applicable for specific solar mounting system) EN 1990 Basis of structural design EN 1991-1-3 Actions on structures / Snow loads EN 1991-1-4 Actions on structures / Wind actions EN 1993-1-1 Design of steel structures / General rules for buildings EN 1993-1-3 Design of steel structures / Supplementary rules for cold formed members EN 1997 Geotechnical design EN 1998-1 Design of structures / General rules, seismic actions and rules for buildings EN 1999-1-1 Design of aluminium structures NEN 7250 Solar systems - ntegration in roofs and facades - Building aspects (pending) BS EN 1991-1-4 British Standard Application To calculate the needed strength, ballast and foundation of the solar mounting system, according the Eurocodes, the specific location details have to be determined, e.g. wind zone, snow zone and height of the building. These need to be entered in the 1-2-3 PV Planner. Foundations and strength of field systems are calculated with SolarTop. Type of solar panel The Van der Valk Solar Systems mounting systems are universal mounting systems for solar panels. Almost any solar panel with of without an aluminium frame, possibly with mounting holes, can be mounted. Types of roof Type of roof covering: bitumen, EPDM, PVC, concrete and other roof coverings. For ballast calculations the exact roof covering must be known. Before installing the solar mounting system, make sure that you carefully sweep the roof area. The ballast calculation for flat roofs only applies for roofs with a slight pitch of up to 5. Above this roof pitch, the system needs to be attached to the roof securely. Ballast Flat roof systems can be attached to the roof or need to be supported by ballast, to make sure that the system is unable to move, lift or tip over. The components supplied do not fully include the ballast required, which will be a number of tiles with a certain measurement and weight. The number of tiles required per position, per type of solar panel, per roof area and per building height is calculated via the 1-2-3 PV Planner and can be seen in the installation instructions and foundation adivse. The number of tiles specified per position will be vital to ensure that the mounting system can be used safely. Position Restrictions also apply for the position of the system on a roof. The solar panels must be installed at a certain distance from the edge of the roof. Follow the scheme in the installation manual calculated by the 1-2-3 PV Planner. Guarantee The guarantee provided is subject to the guarantee conditions stated in the general terms and conditions stipulated by Van der Valk Solar Systems BV. Our terms and conditions can be found on our website: www.valksolarsystems.nl. The ValkBox 3 mounting system is a product that has been produced by: Van der Valk Solar Systems B.V., Registered with the chamber of commerce for Haaglanden under number 27355116. nternet: www.valksolarsystems.nl ssue date : March 2014 Version: General user instructions v1 EN
Necessary Tools For van der Valk Solar Tracker Wrench 10, 13 and 17 Socket 10, 13 and 17 Cordless drill (For socket 10, 13 and 17) 1
Front support type A Cross support type B Rear support type C 72.16.20 Detail: Mounting of the subassembly A/B/C Note: articleno. on support M6x55 77.30.55 Detail: M6 77.30.05 M6x55 (12 Nm) M6x55 (12 Nm) Subassembly A/B/C
Mounting of the subassembly A/B/C Subassembly B Subassembly C Subassembly A Subassembly A/B/C 2
Mounting of the subassembly D 72.06.60 Cable clamp 73.20.10 74.10.07996 72.06.61 6mm 12mm 72.03.20 M8x75 77.40.75 L M8x75 (10 Nm) M8x75 (10 Nm) M8 77.40.05 Click 12 Subassembly D
Mounting of the subassembly E 72.06.60 Cable clamp 73.20.10 74.10.07996 72.06.61 12mm 6mm 72.03.10 M8x75 77.40.75 L M8x75 (10 Nm) M8x75 (10 Nm) M8 77.40.05 Click 6 Subassembly E
Cable clamp 73.20.60 Mounting of the subassembly F 72.10.12 L1 (X+11 [mm]) (L1 [mm]) 71.15.---.---- Note: See page F2 L2 (L2 [mm]) 71.33.----- 11 72.10.26 X V M8x75 77.40.75 M8 77.40.05 Subassembly F
Mounting of the subassembly F Click V M8x75 (18 Nm) M8x75 (18 Nm) M8x75 (18 Nm) Subassembly F 2
Min 80 min 200 100 1810 C.T.C. holes 1750 Foundation page Note: See projet drawing for foundation 74.70.60 Back side Front side 4000 Selection of other foundation options C.T.C. holes 1750 2
Mounting of the subassembly A Subassembly A M10x80 77.50.80 Detail: M10x80 (8 Nm) M10 77.50.05 Use upper hole Subassembly A Subassembly A South North 3
Mounting of the subassembly B and D Subassembly B Detail: Subassembly B Subassembly D Subassembly D 12mm Subassembly B Subassembly D Subassembly A Subassembly A Subassembly B M6x35 77.30.35 Subassembly D M6 77.30.05 Subassembly A Detail: South North M6x35 (10 Nm) 4
Setting up the front carrier profile Detail: 74.90.20 M10x80 77.50.80 M10 77.50.05 1. Slide coupling in the profile M8x20 77.40.20 M8 77.40.05 M8 77.40.07 2. Pull other profile up 3. Slide coupling back 4. Tighten the bolts M8x20 (18Nm) M8x20 (18Nm) M8x20 (18Nm) M8x20 (18Nm) Detail: M10x80 (8 Nm) Use bottom hole South North 5
Mounting of the subassembly E Detail: Subassembly E 6mm Diagonal rod type D M6x20 (10Nm) Detail: Note: Article no. on support Diagonal rod type D Straight rod type E M6x20 77.30.20 M6 77.30.05 M6x20 (10Nm) Straight rod type E Note: There are 2 drifferent types of Rod`s Diagonal rod type D Straight rod type E Detail: M6x20 (10Nm) Straight rod type E Not included south M6x20 (10Nm) North Diagonal Rod type D 6
Mounting of the subassembly F Detail: Subassembly F M8x20 77.40.20 Detail: M8 77.40.05 M8x20 (18 Nm) M8x20 (18 Nm) M8x20 (18 Nm) M8x20 (18 Nm) South North 7
Mounting of the subassembly C Subassembly C Detail: M6x35 M6 77.30.35 77.30.05 M6x35 (10 Nm) South North Subassembly C Subassembly C 8
Setting up the rear carrier profile 74.90.20 Detail: M10x80 77.50.80 4. Tighten the bolts M10 M8x20 M8 M8 77.50.05 77.40.20 77.40.05 77.40.07 1. Slide coupling in the profile 2. Pull other profile up 3. Slide coupling back M8x20 (18Nm) M8x20 (18Nm) M8x20 (18Nm) M8x20 (18Nm) M10x80 (8 Nm) Use upper hole South Detail: North 9
72.18.15 Mounting of the push - pull tubes 74.64.06200 >0mm >0mm 74.65.08080 M8x45 M8x65 77.40.45 77.40.65 Detail: Detail: M8 M8 77.40.05 77.40.07 M8x45 (10 Nm) M8x65 (8 Nm) Note: Mount all the tubes in horizontal position when subassembly F us in horizontal position Detail: 80 mm 6200 8000 10
Mounting of the actuatorbracket M8x20 74.80.20 77.40.20 M8x20 (12 Nm) M8x20 (12 Nm) Note: Place actuator see project drawing M8 77.40.05 Detail: M8x20 (12 Nm) M8x20 (12 Nm) South North 11
Lm = Mountinglength Mounting of the actuator Lm 78.85.12 78.85.60 Detail: M8x65 77.40.65 M8 77.40.05 Detail: M8x65 (8 Nm) 1 3 2 South 4 North 12
Mounting of the actuator 72.18.16 M8x65 78.85.60 77.40.65 Detail: M8 77.40.05 Before tightening the bolts make sure the tracker Subassembly F is horizontal position 3 5 M8x65 (8 Nm) 4 6 1 Detail: 2 South North 13
74.80.21 Mounting of the actuatorhood Detail: M8x65 77.40.65 M8 77.40.05 M8x65 (12 Nm) M8x65 (12 Nm) M8x65 (12 Nm) M8x65 (12 Nm) South North 14
Mounting of the solar panels Not included Page 16 Junction box up Junction box up South North 15
Mounting of the solar panels Detail: click Detail: M8x35 (10 Nm) 16
Mounting of the end caps 72.92.60 72.91.32 Detail: Detail: Detail: Click South North 17
Van der Valk Solar Systems Van der Valk Solar Systems is a specialist company that is fully focused on developing and producing mounting systems for use with solar panels. To this end we work in close collaboration with Van der Valk Systemen, our sister company. Van der Valk Systemen has been a well-known name in the field of moving systems and stationary components for the greenhouse horticultural sector and industry throughout the world since 1963. Van der Valk Systemen s high quality products have been individually developed from a scientific approach and produced with mathematical precision. They are made to be low-maintenance and to stand out thanks to their durability, reliability, functionality and ease of assembly. Both Van der Valk Systemen and Van der Valk Solar Systems only introduce innovative products to the market. Our shared business complex consists of 20,000 m2 of offices and production facilities, in which modern machinery and the latest technologies facilitate development, manufacturing and testing that is fast, flexible and precise. We develope and produce solar mounting systems for: Open fields Pitched Roofs Flat roofs Greenhouses Water features PLEASE CONTACT VAN DER VALK SOLAR SYSTEMS, YOUR NSTALLATON COMPANY OR PROJECT ORGANSATON FOR FULL NFORMATON.