GPS/GPRS/GSM AVL VEHICLE TRACKING SYSTEM OPERATION MANUAL MODEL: ET700A/C

GPS/GPRS/GSM AVL VEHICLE TRACKING SYSTEM OPERATION MANUAL MODEL: ET700A/C Copy rights preserved @ ExtremTrac Technology Co.,Ltd

Contents 1. General Introduction... 3 2. Applications 3 3. Package 3 4. Operation & installation... 4 5. GPRS remote Configuration... 13 6. PC program configuration... 15 7. System LED status instruction... 19 8. Mobile display configuration..... 20 9. Firmware upgrade.... 21 10. Appendix..... 23 11. Technical parameter..... 25 2

General Introduction: The ET700A/C is a small yet powerful GPS, GSM/GPRS vehicle tracking device, Optional mobile data terminal or handset phone for 2 way voice/ message communications. Built-in 800Mah battery for long lasting operation without external power, built in memory for data logging of 30,000 waypoints, harsh-weather and shock resistant PCB design, It has outstanding multiple inputs and outputs: door lock/unlock, cut relay, taxi odometer, oil level sensor, temperature sensor, original car alarm systems, digital camera for image monitoring, etc. It is designed for almost any vehicles. With its compact and small size, (Cigarette box size), easy hide and installation inside the vehicle. GPS Technology 1. Applications: 1. For vehicles which have 12V or 24V battery power supply. 2. Transmit data either by GPRS/GSM 3. Support TCP/UDP ( in big data transfer like image, system switch to UDP transmission automatically) 2. Package: 3

3.Operation and Installation 1 Specifications 1.1 Specification of Power Supply 1. Power supply input: DC 8~36V, compatible with 12V & 24V series veh 2. Low power consumption: DC12V <110mA;Dormant: 50mA; 3. Backup battery: built-in backup battery with 3-hour standby time. 1.2 Input and output configuration 1. 7 inputs: 5 positive triggers, 2 negative triggers 2. 3 negative outputs. 2. Wire Diagram: 4

2.1 wire installation table Item Color of cable connection points Function Red 12PIN-1 Positive pole of car battery Positive pole input of main power. Black 12PIN-5 Negative pole of car battery Negative pole input of main Main cable (12pin) power. Orange12PIN-2 Emergency button trigger Emergency alarm signal trigger Orange12PIN-5 Emergency negative input Emergency alarm signal input Purple 12PIN-4 Stolen alarm positive trigger detecting Stolen alarm signal input Yellow 12PIN-10 Negative trigger detecting negative trigger signal input Brown 12PIN-3 Connect to ACC ON position of start switch Detect start (on)signal of vehicle Blue12PIN-6 Connect with blue cable of relay Control input of cutting oil& circuit Pink 12PIN-7 Positive input of sensor Positive trigger signal input White-black 12PIN-12 Optional sensor Positive trigger signal input Blue-white 12PIN-8 Door unlock negative output Negative power supply output Green-white 12PIN-9 Door lock negative output Negative power supply output Gray 12PIN-11 Optional sensor Optional sensor Main cable 2 2 PIN Speaker Speaker pin Main cable 9 9PIN Handset phone handset phone pin Relay cable Red (thick) 30 Positive pole of oil pump Or engine startup Power port of cutting oil & circuit relay Green (thick) 87a Black( thin ) 87 Positive pole of oil pump or engine startup Negative pole of vehicle battery Non-power port of cutting oil& circuit relay Negative pole cable of pilot light for cutting oil& circuit 5

2.2 Function Explanation of Terminal Signal Cable 1 Terminal Signal Cable connect to 12-pin joint on the terminal 1 Red wire(thin, with safety switch;):power supply input (DC12V/24V). 2 Orange wire: emergency button signal cable.( work in negative pole) 3 Brown wire: Detect wire for ignition switch (KEY-ON/OFF state) 4 Purple wire: positive trigger, stolen alarm input.( the alarm signal is required to last for 5 seconds or 8 seconds with 6 impulses 5.Black wire (thick):the one with shape Y port is power supply earth. Black wire (thin): emergency button earth. 6 Blue wire: negative output of cutting oil & circuit. 7 Pink wire: door positive input. 8 White-blue wire: Door unlock negative output. 9 White-green wire: door lock negative output 10 Yellow: Door negative signal input. Relay: A Red wire (thick) AWG14#1015 oil & circuit cutting. B Red wire (thin) AWG22#1007, connects to DV12Vor 24V ( positive pole of relay coil) C Black wire (thin): Negative pole of light-emitting diode, connects to earth. D Green wire (thick) AWG14#1015: oil & circuit cutting. E Blue wire (thin) oil & circuit cutting; signal controlling. 6

3.1 Preparation 7

1. Make sure that no item in the package contents is missed before you install the GPS vehicle terminal. 2. Prepare a SIM with SMS or GPRS function. 3. Test the basic vehicle situation (such as light, brake, ignition, anti-theft device and all wires related to GPS installation.) before you install the GPS vehicle terminal. 4. Safety Precaution: 4.1 Make sure that the SIM card is valid and inform the control center of SIM card number and necessary customer information. 4.2 Choose a proper position to install the terminal. 4.3 Remove the components of vehicle correctly during installation. 4.4 Lay and bundle the vehicle cables as the original direction. 4.5 Protect the joints with insulating tape.(withstands 600v ) 3.2 Installation Position 1. The installation should not affect the driver s operation. 2. The installation should not affect the look and basic functions of vehicle (such as removing,winding up and down the seat) 3. The installation position should be protected from water. 4. The joints should be bundled with insulating tape to avoid crush and short circuit. 5. The installation position should be away from direct sunshine. 6. The terminal should be installed in a concealed place 7. The terminal should be fixed in a position with screw or band. 8. Recommendatory installation position: a place under back seat or the side of trunk. 3.3 Installation of SIM card and Backup Battery 1. Installation of SIM card: 1.1 Open the side panel of the terminal. 1.2 Pull out the SIM card holder, insert SIM card and push the SIM card holder back until it click. Caution: Make sure that the power supply( including backup battery) is turned off when installing SIM card 8

a. Screw off the back cover of the ET700A/C unit.. b. Insert the SIM card. 3.4.1. Installation of backup battery : 1.1 Open the SIM card panel. 1.2 Shift the switch of backup battery to ON position to turn the battery on.( shown as the fig. on top) 1.3 Shift the switch of backup battery to ON position to turn the battery off. 1.4 The factory status of the backup battery is 70% charged. 1.5 When first installation of the terminal is finished, the backup battery will full charge itself automatically. Caution: Do not use the backup battery before installation or in the situation that the terminal is not used. please insert the SIM card first then power on the tracker. a. Connect ET700A/C to a 12V external battery, connect GPS/GSM antennas, ( the antennas must be placed in open area where there is good GPS/GSM signal). For testing, no need to install in vehicle, 9

just connect 3 connectors: GPS antenna, GSM antenna, power. b. Watch the LEDs for 3 minutes, when green LED flashes at every 2 times, and red LED every 3 times, ( green LED and red LED flashes simultaneously for 2 times, red LED flashes one more time), that means the tracker now is ready to work, good GPS and GSM signal, now user can start to configure the device: Each time when power off the tracker, please watch the LED status, only when green LED and red LED flashes simultaneously for 2 times, red LED flashes one more time 3.4.2.Connection of Power Supply 1. Red wire Positive pole of power supply input; with safety switch, DC 12V&24V. Black wire Negative pole of power supply input 2. Installation Position The wires should be connected under the dashboard. 3. Wiring 4.1 Connect the red wire with positive pole of power supply and and the black wire with negative pole respectively. Make sure the connection is steady and concealed. 4.2 Turn on the backup battery. 4.3 Wrap the joint with insulating tape. Don t let the joint uncovered. 4.4 Keep the power supply of the terminal working normally when the engine is off. Caution: Avoid short circuit and open circuit when connecting the cables, otherwise the vehicle device and auto system may be damaged. 3.5 Connection of Emergency Button( Orange wire) 1 Function 1.1 Call for police by pressing the emergency button in emergency (such as hijacking, sick and vehicle trouble.) 1.2 The handset will prompt you with twice tones when calling for police successfully. 2 Installation 2.1 Installation Position A sound installation position should be easy to reach and concealed; The surface of installation position should be flat and free of wax or dirt. 2.2 Wiring Connect the socket of emergency button to the plug on the top of the orange wire. Wrap the joint with insulating tape to avoid disconnection. 3.6 Connection of Stolen alarm(purple cable) 10

3 Function 1.3 Any unauthorized entering will trigger stolen alarm. 1.4 5-second positive (negative) pole output of anti-theft device is regarded as stolen alarm.( 6 times impulse output in 8 seconds is regarded as stolen alarm as well.) 4 Installation 2.3 A key point needs to be confirmed first: The engineer should confirm if the trigger of stolen alarm is negative or positive.e.g. the device output is positive pole or negative pole when it alarms. 2.4 Wiring 2.3.1 Testing wire for positive trigger of stolen alarm is purple; If the trigger is negative signal, a signal switch is needed. 2.3.2 Connect the testing wire for output pority of alarm device to the signal port of alarm device. Caution: The testing wire of stolen alarm is compatible with impulse alarm signal of the vehicle. It takes 10 seconds to test. 3.7 Connection of detecting wire(key ON/OFF)(Brown wire) 1. Function Test the vehicle status: KEY OFF or KEY ON state 2. Installation 2.1 A key point needs to be confirmed first: 2.1.1 Test if the voltage is 12V(or 24V) when the ignition switch is turned to ON position; Test if the voltage is 0 when the ignition switch is shifted to OFF position. 2.1.2 Test method: Turn the key to OFF position, a wire detected with electricity is power supply input; Ignition Switch Then turn the key to ACC position, the wire detected with 12V voltage output is audio power supply; 11

Turn the key to ON position, the wire detected with 12V voltage input is the ignition cable. 2.2 Wiring Connect the brown wire to the ignition wire and wrap the joint with insulating tape.(caution: the testing cable must be connected to the ON position. Don t connect it to the oil pump or ACC position.) 2.3 Test: Configure the terminal with control center number and turn off the engine. In automatic arm state (or arm state realized by password), the terminal should cut the oil and circuit. 3.8 Installation of Sound Monitoring and hands-free microphone 1 Function: Sound monitoring or hands-free talk. 2 Installation The microphone should be installed close to the driver. Recommendatory distance is 50 cm. Insert the plug of microphone to the MIC port on the terminal. Protect the microphone wire from squeezing and plucking, otherwise it may be damaged. Don t bundle the microphone wire together with GSM antenna, otherwise there will be a loud noise. Test: Both party could hear each other clearly; No noise and the volume is normal during a hands-free talk. 3.9 Electricity failure alarm for terminal and vehicle battery 3. Function 1.1 The terminal detects the alarm of abnormal electricity failure (protecting the vehicle from theft and damage) 1.2 If the voltage of vehicle battery is less than DC 10.3V for 30 seconds, the terminal will create low power alarm automatically. 1.3 If the voltage of vehicle battery is less than DC5.0V, the terminal will create electricity failure alarm. 1.4 The built-in battery is designed with high voltage protection and 3-hour standby time. 4. Installation 1.1 The built-in backup battery is required to use before installing this alarm. 1.2 Open the SIM panel and shift the switch of backup battery to ON position. 5. Test: The handset should be power off if the power of the host is cut; Caution: this function is only available for GPS terminal with backup battery. 12

3.10 Connection of oil and circuit controlling wire 1. Function Control the oil and circuit of vehicle; disable the vehicle. 2. Installation 2.1 A key point needs to be confirmed first: The controlling output is blue wire. 2.2 Wiring Connect the controlling wire with the blue cable of terminal with 1 joint. 2.3 Test: 2.3.1 Oil & circuit cutting test: configure the terminal with control center number. Ignite the engine in arm state, the terminal will cut off the oil & circuit automatically ( with LED indication).the function can be accomplished by remote control. 2.3.2 Oil & circuit resuming test: the terminal will resume oil& circuit in disarm state 3.11 Installation of Handset 1 While installing the handset holder with twin adhesive, keep the surface of the holder smooth and free of wax or dirt. 2 Connect the socket of the handset to the related plug on the terminal. If the connection is not smooth, adjust the plug. Don t connect them by force. Wrap the joint with insulating tape to avoid disconnection. 3.12 Installation of GSM Antenna 1. The GSM antenna should be installed close to the windows.( a place with strong signal strength). 2. The GSM antenna should be installed in a concealed place to avoid damage. 3. The distance between the GSM antenna and metal surface should be 5cm, which is good to signal receiving when the vehicle is driven in a high speed. 4. Protect the antenna wire from squeezing, otherwise it may be damaged. 5. Check the indication light: It will flick 3 times every 5 seconds if GPRS is connected: flick 2 times every 5 second if GSM is connected; flick once every 5 seconds if GSM is not connected. 3.13 Installation of GPS Antenna 1. Fix the GPS antenna, which should be not covered by any mental objects. The recline angle may not 13

be greater than 15 degree. The antenna should be installed in a proper position such as front and back bumper, top of the vehicle and front windows or under back window (the GPS antenna should not be installed if there is any rupture risk in the back window). 2. The upside (camber side ) of the GPS antenna should face the sky. The GPS antenna should not be covered by any object. 3. The downside (smooth and with letter on it) is magnetic. You may put it on a iron surface or stick it with twin adhesive. 4. Protect the antenna wire from squeezing, otherwise it may be damaged. 5. Check the indication light: It will flick 3 times every 5 seconds if GPS is connected: flick once every 5 second if GPS is not connected; black off once every 5 seconds if GPS antenna is short circuit. 3.14 Theory and Application of Signal Switch 14

Remote configuration of ET700A/C units by GPRS. ET700A/C CONTROL PANEL Important notice: the ET700A/C ID number should be the last 10 digit of the device serial number printed on the side case. Figure Nº 1: 1.0 Authenticate: Please introduce the USER and PASSWORD of your account then click on CONNECT. Once you are connected all the car subscribed to your account will be listed in the DEVICE LIST field, the cars in RED color are disconnected and the cars with GREEN color are connected now to the system, the unit status can change if the car keeps the connection with the server, sometimes 15

the car disconnect and get connect again, if it is not please make click on REFRESH button. Once you have selected desired car please click on OPEN button to establish connection with it. Once this step is done all configuration fields will become enable and you can star to use the panel with that car. Figure Nº 2: 2.0 CONTROL MESSAGE: This will allow you to have control over the car, like lock or unlock the car doors, here you can select the OIL option in the CTRLNO field and then the desired operation to stop the car engine or let it start again. You have two different ways to turn off the car one intelligent and other immediately, the intelligent way the car will turn off the engine when speed be equal to cero, and the immediately 16

way the car will turn off the engine at the same moment of the request, and it doesn t matter the speed. 3.0 GPS QUERY Polling action. 4.0 LISTEN MESSAGE Please place in the PHONE NUMBER field the phone number where you want to receive the call from the car, for example: +61414469737 then press START and the device in the car will call to the number placed in the PHONE NUMBER field. To STOP the call, select stop or just hangout the call. 5.0 SURVEILLANCE DATA. In this section you can configure the report frequency of the car, you can tell to the device to send a position report each 60 seconds (1 minute) or 180 seconds (3 minutes) 300 seconds (5minutes) or the frequency that you want, the time it is expressed in seconds. You can set the device to send a position report each XXX meters this is in case you want position reports by distance. The value is expressed in METERS. Select Stop Distance And Time, if you want no more position report from that car. After you set your configuration make click on SEND button 6.0 OVERSPEED Use this section to set the over-speed limit of the car in the OVERSPEED KM/H field place the limit allowed speed and in the TIME SPEED field put the time you will allow to the car to go on that 17

limit speed, this time is expressed in seconds. After your configuration click on SEND button. 7.0 REPONSE DEVICE There is a big white square in the center of the console in that field you can read all your request and check the device answers. 8.0 TEXT INFORMATION If your ET700A/C has a MDT accessories you can send text to that accessory thru this section, to do this just write the message that you want to send to the driver and then click SEND button. Device Setting Up by PC RS232 connection: 18

This PC based set up software is used to set up and monitor the parameter configuration of the ET700A/C tracker. Please connect ET700A/C with PC by the RS232 cable. Power on the unit and reset: Start software: Click this button to start the software \ Open COM port Select the right COM port Tick Open button 19

indicates the related COM port is being opened. Is the selected COM port is busy or not available, users can not open it. Click confirm button click Close to close the interface 20

Set up the system parameters. Tick Get Parameter button, wait for 5 seconds, below windows will appear: Click Set Parameter and wait for 3 seconds, the configuration will be saved successfully. 21

GPS/GPRS LED status: There are 2 LEDs on the side of the ET700A/C: S means GPS LED, M means GSM LED. A. S LED indicates the GPS working status S LED flash 3 times at every 5 seconds, means ET700A/C has valid GPS signal S LED flash 1 time at every 5 seconds, means ET700A/C does not have valid GPS signal S LED turn off at every 5 seconds, means the ET700A/C antenna get short-circuit. S LED always be on, means the GPS antenna connect is well B. M indicates the GSM working status M LED flashes 3 times at every 5 seconds, GPRS get connected M LED Flashes 2 times at every 5 seconds, has GPRS signal M LED Flashes 1 time at every 5 seconds, GPRS no signal Configuration by mobile data display: Using the ET700A/C mobile data terminal, users can set up the ET700A/C main unit: 1. Request for the latest version of the software program: Function: Request the information of updated time and features of the software firmware. 22

Command: *#3# Note: when enter this command through the display terminal, there will be a string of numbers which indicate the updated time of the firmware. 2. Set the central configuration number and request command for this number ( if forget) Function: set the remote configuration number or request command for this number Command to request the central configuration number through display terminal: *#53# Set central number: *#53*1* central number# Note: if do not want to set the central number, just let it be empty i.e. *#53*1* # 3.Set the GPRS parameters: Function: set the IP address and port. Command: *#42*192*168*0*12*8002# Note: in the above, 192*168*0*12 is IP address, 8002 is port 4. set the unit ID number: Function: set the tracker ID number Request command: *#52# Note: the tracker unit has its own default ID number set in factory; it is the last 10 digits of the bar code. For example: the car code is: 632000122588. Then the ID number is 2000122588 Note: Command to set the new ID number: *#52*10000# Note: 10000 is the new ID code 5. auto fence or non auto fence ( optional for taxi) Function: set the tracker to be auto fence or not auto fence Request command: *#54# Note: enter 1 or 0. 1 means auto fence, 0 means non auto fence 6. GPRS connection configuration Function: IP address and Port Central IP address: 222.35.61.66 PORT:8000 APN:CMNET, Command: *#42*222*35*61*66*8000*3545463752# Note: since the display terminal only has numbers, but APN contains the letters, so please refer to below chart. The chart shows how to transform the letters & code into only numbers: 7. System re-set: *#14# 23

Firmware Upgrade Instruction Operation Steps: 1. Connect the ET700A/C with PC by the RS232 cable, power on. 2. Run the program IAP2006.exe, system will appear below interface: After connected the device with PC serial port, click Then below interface will show up ( note: when in this process, the program will check the ET700A/C firmware version, this may need some time, and sometimes it is normal when shows over time error, in this situation, users need to quit the program and re-start again) 24

When software detected the upgrading program is consistent with the ET700A/C firmware version, Then click button, then system will start to upgrade the firmware. Note:before upgrading, need to check if the hardware version is consistent with the upgrading program. When in upgrading, it shows the processing speed, after this, system will check the uploaded data. As below shows: 25

Appendix Dec Char Dec Char Dec Char 00 SPACE 33 A 66 b 01! 34 B 67 c 02 " 35 C 68 d 03 # 36 D 69 e 04 $ 37 E 70 f 05 % 38 F 71 g 06 & 39 G 72 h 07 ' 40 H 73 i 08 ( 41 I 74 j 09 ) 42 J 75 k 10 * 43 K 76 l 11 + 44 L 77 m 12, 45 M 78 n 13-46 N 79 o 14. 47 O 80 p 15 / 48 P 81 q 16 0 49 Q 82 r 17 1 50 R 83 s 18 2 51 S 84 t 19 3 52 T 85 u 20 4 53 U 86 v 21 5 54 V 87 w 22 6 55 W 88 x 23 7 56 X 89 y 24 8 57 Y 90 z 25 9 58 Z 91 { 26 : 59 [ 92 27 ; 60 \ 93 } 28 < 61 ] 94 ~ 29 = 62 ^ 95 DEL 30 > 63 _ 96 换 行 31? 64 ` 97 enter 32 @ 65 a For example: central server IP address is:222.35.61.66 PORT:8000 APN:CMNET, 26

User can set this command through display terminal: *#42*222*35*61*66*800 Technical parameter Item Working voltage Power source anti- ties Technical parameter 8 ~ 36V/DC 80V Average 110mA @ DC 12V Working electric current Sleeping <50mA @DC 12V Terminal unit size 88 62.5 32.5 mm ( LXWXH ) Net weight Gross weight 0.26kg (Outer cover of Aluminium alloy) 0.98kg (with standard package) SIEMENS MC39i 900Mhz, 1800Mhz SIEMENS MC56 850Mhz, 900Mhz, 1800Mhz GSM module frequency BenQ M23A 900Mhz, 1800Mhz WAVECOM. Philip Q24NG 850Mh 900Mh 1800Mh 1900Mh Tracks up to 12 satellites of GPS GPS performance Position precision<15 meters CEP without SA Cold start time< 48 sec. Antenna GPS SMA connection, - 26dB, Cable length 5M GSM SMA connection, - 3dB, Cable length 3M Working temperature -20 ~ +60 Working humidity 5% ~ 95% Store temperature -40 ~ +85 Backup battery Nickel- hydrogen 4.8V/DC 500 mah Altitude 18,000 meters (60,000 feet) max GPS dynamic Conditions: GPRS feature Velocity 515 meters / second (1000 knots) max Acceleration 4G, max 2 Watts EGSM (GSM900 Class 4) 1 Watt GSM1800 (DCS1800 Class 1) GPRS class 10 27

Audio support (with echo-cancellation and noise reduction) Data transfer modes: GPRS (TCP/UDP) SMS PDU (buffered with up to 4 positions per SMS) Product warranty Customer s information Name Phone Mobile Address Serial number Date of purchase Supplier Retailer Remarks 1. The warranty is valid for 1 year of product maintenance (excluding improper uses) starting from the date of purchase. 2. Should the product malfunctioned under proper use, free maintenance service is provided within warranty period. This service does not cover due to human causes, natural causes. 3. Serial numbers on the warranty must be the same as it is shown on the main unit. 4. The company is not responsible for re-issuing the product warranty if it is lost. 5. Warranty is invalid without supplier s seal or defaced. 6. Service fee is charged if warranty period is over or product warranty is not shown with. 28