SLING LEG OPTIONS Standard End Fitting Combinations To order sling legs, choose the correct size from the tables on the following pages. Determine the length needed and specify the end fittings required from the list of combinations shown below. Two, three, and four leg spreaders will be fabricated with oblong Master links, unless otherwise specified. STANDARD EYE & STANDARD EYE STANDARD EYE & THIMBLE with Shackle Sealed in Thimble STANDARD EYE & THIMBLE STANDARD EYE & HOOK THIMBLE & SLIP-THRU THIMBLE STANDARD EYE & OPEN SWAGE SOCKET CRESCENT THIMBLE & STANDARD EYE SLIP-THRU THIMBLE & STANDARD EYE STANDARD EYE & CLOSED SWAGE SOCKET THIMBLE & THIMBLE SLIP-THRU THIMBLE & HOOK THIMBLE & HOOK SLIP-THRU THIMBLE & SLIP- THRU THIMBLE EYE & THIMBLE with Sliding Choker Hook EYE & EYE with Sliding Choker Hook 30
1-PART SLINGS/MECHANICAL SPLICE (CHOKER) SINGLE LEG SLINGS Extra improved plow steel IWRC (EIPS) CHOKER BASKET BASKET AT DEGREES 60 DEGREE 45 DEGREE 1/4.65.48 1.3 1.1.91.65 5/16 1.74 2 1.7 1.4 1 3/8 1.4 1.1 2.9 2.5 2.0 1.4 7/16 1.9 1.4 3.9 3.4 2.7 1.9 1/2 2.5 1.9 5.1 4.4 3.6 2.5 9/16 3.2 2.4 6.4 5.5 4.5 3.2 5/8 3.9 2.9 7.8 6.8 5.5 3.9 3/4 5.6 4.1 11 9.7 7.9 5.6 7/8 7.6 5.6 15 13 11 7.6 1 9.8 7.2 20 17 14 9.8 1-1/8 12 9.1 24 21 17 12 1-1/4 15 11 30 26 21 15 1-3/8 18 13 36 31 25 18 1-1/2 21 16 42 37 30 21 1-5/8 24 18 49 42 35 24 1-3/4 28 21 57 49 40 28 1-7/8 32 24 64 56 46 32 2 37 28 73 63 52 37 2-1/8 40 31 80 69 56 40 2-1/4 44 35 89 77 63 44 2-3/8 49 38 99 85 70 49 2-1/2 54 42 109 94 77 54 2-5/8 60 46 119 103 84 60 2-3/4 65 51 130 113 92 65 2-7/8 71 55 141 122 100 71 3 77 60 153 132 108 77 3-1/8 82 64 165 143 117 82 3-1/4 89 69 177 153 125 89 3-3/8 95 74 190 165 135 95 3-1/2 102 79 203 102 144 176 30 DEGREE Rated Capacities Basket Hitch based on D/d ratio of 25. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. Rated Capacities shown apply only to 6x19 and 6x37 classification wire rope. 31
1-PART SLINGS/MECHANICAL SPLICE 2-LEG SPREADERS 2-LEG SPREADERS 60 DEGREE 45 DEGREE 30 DEGREE LENGTH 1/4 1.1.91.65 5/16 1.7 1.4 1 Extra improved plow steel IWRC (EIPS) 3/8 2.5 2 1.4 7/16 3.4 2.7 1.9 1/2 4.4 3.6 2.5 9/16 5.5 4.5 3.2 5/8 6.8 5.5 3.9 3/4 9.7 7.9 5.6 7/8 13 11 7.6 1 17 14 9.8 1-1/8 21 17 12 1-1/4 26 21 15 1-3/8 31 25 18 1-1/2 37 30 21 1-5/8 42 35 24 1-3/4 49 40 28 1-7/8 56 46 32 2 63 52 37 2-1/8 69 56 40 2-1/4 77 63 44 2-3/8 85 70 49 2-1/2 94 77 54 2-5/8 103 84 60 2-3/4 113 92 65 2-7/8 122 100 71 3 133 108 77 3-1/8 143 117 82 3-1/4 153 125 89 3-3/8 165 135 95 3-1/2 176 144 102 Rated Capacities Basket Hitch based on D/d ratio of 25. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. Rated Capacities shown apply only to 6x19 and 6x37 classification wire rope. 32
1-PART SLINGS/MECHANICAL SPLICE 3-LEG SPREADERS LENGTH Extra improved plow steel IWRC (EIPS) 3-LEG SPREADERS 60 DEGREE 45 DEGREE 30 DEGREE 1/4 1.7 1.4.97 5/16 2.6 2.1 1.5 3/8 3.7 3.0 2.2 7/16 5.0 4.1 2.9 1/2 6.6 5.4 3.8 9/16 8.3 6.8 4.8 5/8 10 8.3 5.9 3/4 15 12 8.4 7/8 20 16 11 1 26 21 15 1-1/8 31 26 18 1-1/4 38 31 22 1-3/8 46 38 27 1-1/2 55 45 32 1-5/8 63 52 37 1-3/4 74 60 42 1-7/8 84 68 48 2 95 78 55 2-1/8 103 84 60 2-1/4 116 94 67 2-3/8 128 105 74 2-1/2 141 115 82 2-5/8 155 126 89 2-3/4 169 138 97 2-7/8 183 150 106 3 199 162 15 3-1/8 214 175 124 3-1/4 230 188 133 3-3/8 247 202 143 3-1/2 264 215 152 Rated Capacities Basket Hitch based on D/d ratio of 25. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. Rated Capacities shown apply only to 6x19 and 6x37 classification wire rope. 33
1-PART SLINGS/MECHANICAL SPLICE 4-LEG SPREADERS LENGTH 4-LEG SPREADERS 60 DEGREE 45 DEGREE 30 DEGREE 1/4 2.2 1.8 1.3 5/16 3.5 2.8 2.0 Extra improved plow steel IWRC (EIPS) 3/8 5.0 4.1 2.9 7/16 6.7 5.5 3.9 1/2 8.8 7.1 5.1 9/16 11 9.0 6.4 5/8 14 11 7.8 3/4 19 16 11 7/8 26 21 15 1 34 28 20 1-1/8 42 34 24 1-1/4 51 42 30 1-3/8 62 50 36 1-1/2 73 60 42 1-5/8 85 69 49 1-3/4 98 80 57 1-7/8 112 91 64 2 127 104 73 2-1/8 138 113 80 2-1/4 154 126 89 2-3/8 171 139 99 2-1/2 188 154 109 Rated Capacities Basket Hitch based on D/d ratio of 25. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. Rated Capacities shown apply only to 6x19 and 6x37 classification wire rope. 34
STAINLESS STEEL/MECHANICAL SPLICE SINGLE LEG SLINGS CHOKER BASKET 1/4.61.45 1.2 5/16.86.63 1.7 3/8 1.1.84 2.3 7/16 1.5 1.1 3.1 1/2 2.2 1.6 4.3 Stainless steel Type 302 or 304 IWRC 9/16 2.7 2.0 5.4 5/8 3.3 2.5 6.7 3/4 4.7 3.5 9.4 7/8 6.3 4.7 13 1 8.1 6.0 16 1-1/8 10 7.4 20 1-1/4 12 9.1 25 1-3/8 14 11 29 1-1/2 17 13 34 1-5/8 20 15 40 1-3/4 22 17 45 1-7/8 25 19 51 2 28 21 57 2-1/8 32 23 63 2-1/4 35 25 69 Rated Capacities Basket Hitch based on D/d ratio of 25 Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. Rated Capacities shown apply only to 6x19 and 6x37 classification wire rope. 35
STAINLESS STEEL TYPE 302 AND 304/MECHANICAL SPLICE IWRC TWO-LEG BRIDLE of 2,000 lbs. Rated capacities shown apply only to 6x19 and 6x36 classification wire rope. 60 DEGREE 45 DEGREE 30 DEGREE 1/4 1.1 0.86 0.61 5/16 1.5 1.2 0.86 3/8 2.0 1.6 1.1 7/16 2.7 2.2 1.5 1/2 3.8 3.1 2.2 9/16 4.7 3.8 2.7 5/8 5.8 4.7 3.3 3/4 8.2 6.7 4.7 7/8 11 8.9 6.3 1 14 11 8 1-1/8 17 14 10 1-1/4 21 17 12 1-3/8 24 20 14 1-1/2 29 24 17 1-5/8 33 27 19 1-3/4 38 31 22 1-7/8 43 35 25 2 48 39 28 2-1/8 52 42 30 2-1/4 57 46 33 Rated Capacities Basket Hitch based on D/d ratio of 25 Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. 36
STAINLESS STEEL TYPE 302 AND 304/MECHANICAL SPLICE IWRC THREE-LEG BRIDLE of 2,000 lbs. Rated capacities shown apply only to 6x19 and 6x36 classification wire rope. 60 DEGREE 45 DEGREE 30 DEGREE 1/4 1.6 1.3 0.91 5/16 2.2 1.8 1.3 3/8 3.0 2.4 1.7 7/16 4.0 3.3 2.3 1/2 5.6 4.6 3.2 9/16 7.1 5.8 4.1 5/8 8.6 7.1 5.0 3/4 12 10 7.1 7/8 16 13 9.5 1 21 17 12 1-1/8 26 21 15 1-1/4 31 25 18 1-3/8 36 30 21 1-1/2 43 35 25 1-5/8 50 41 29 1-3/4 57 46 33 1-7/8 64 52 37 2 72 58 41 2-1/8 78 63 45 2-1/4 85 69 49 Rated Capacities Basket Hitch based on D/d ratio of 25 Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. 37
STAINLESS STEEL TYPE 302 AND 304/MECHANICAL SPLICE IWRC FOUR-LEG BRIDLE of 2,000 lbs. Rated capacities shown apply only to 6x19 and 6x36 classification wire rope. 60 DEGREE 45 DEGREE 30 DEGREE 1/4 2.1 1.7 1.2 5/16 3.0 2.4 1.7 3/8 3.9 3.2 2.3 7/16 5.4 4.4 3.1 1/2 7.5 6.1 4.3 9/16 9.4 7.7 5.4 5/8 12 9.4 6.7 3/4 16 13 9.4 7/8 22 18 13 1 28 23 16 1-1/8 34 28 20 1-1/4 41 34 24 1-3/8 49 40 28 1-1/2 58 47 33 1-5/8 67 54 38 1-3/4 76 62 44 1-7/8 85 70 49 2 95 78 55 2-1/8 104 85 60 2-1/4 113 93 66 Rated Capacities Basket Hitch based on D/d ratio of 25 Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. 38
CABLE LAID SLINGS/MECHANICAL SPLICE MECHANICAL TYPE SPLICE RATED CAPACITIES IN SINGLE PART SLING CHOKER TWO LEG SPREAD OR BASKET BASKET 60 DEGREE 45 DEGREE 30 DEGREE 7 x 7 x 7 CONSTRUCTION 1/4.50.34 1.0 0.87 0.71 0.50 3/8 1.1.74 2.2 1.9 1.5 1.1 1/2 1.9 1.3 3.7 3.2 2.6 1.9 5/8 2.8 1.9 5.5 4.8 3.9 2.8 7 x 7 x 19 CONSTRUCTION 3/4 4.1 2.8 8.1 7.0 5.8 4.1 7/8 5.4 3.7 11 9.3 7.6 5.4 1 6.9 4.7 14 12 9.7 6.9 1-1/8 8.3 5.8 17 14 12 8.3 1-1/4 9.9 7.0 20 17 14 9.9 Rated Capacities Basket Hitch based on D/d ratio of 10 or greater. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Horizontal Sling angles less than 30 degrees shall not be used. 39
MULTI-PART Delta Rigging and Tools Multi-Part slings are flexible, snug up tightly around the load in choker hitches, and quickly regain shape after a lift. They also offer outstanding handling characteristics, particularly in the larger rated capacities. When loaded, stress is equally distributed to all rope parts in the sling body due to the helical manner in which ropes are laid together. Braided slings are formed by continuously plaiting, or braiding, several ropes together to form the sling body and both eyes in a single fabrication operation. Ends of individual ropes are usually hand-tucked or mechanically spliced into component ropes of the body. Eyes are wrapped and given a rubberized coating since eyes are not braided. Braided slings are often selected where loads must be rolled or maneuvered, since the design creates friction to grip loads and resist rotation. MULTI-PART BODY BRAIDED CONSTRUCTION High flexibility is achieved by braiding, or plaiting, one or more wire ropes to form a fabric for the sling body. Component ropes run continuously through body and eyes, ends are hand-tucked into sling body or secured with pressed sleeves. 6-part sling is flat, 8-part sling is round. HAND SPLICE Each sling is hand fabricated by laying together one or more ropes in a helical manner, so component ropes run continuously through the eyes and sling body. Ends are secured into component rope by hand-tucked splices. BRAIDED MECHANICAL SPLICE Three wire ropes are helically laid by hand to form a 3-part fabric, from which sling bodies of 3 or 9 parts may be made by helically laying one or three parts of fabric together. Mechanical splices form the eyes that provide centerline pull along the sling body. Same number of rope parts in the sling eyes as in the body. Each sling is proof loaded before shipment. 4, 5 and 7-part Multi-part slings with either mechanical or hand eye splices are available on special order. 42
MULTI-PART BODY SINGLE LEG 3-PART 3-PART HAND SPLICE MECHANICAL SPLICE 3-PART SIMPLE LEG WIRE SLING RATED CAPACITY ()* EYE BASKET HITCH DIMENSIONS SLING DIA. CHOKER** 90º 60º 45º 30º A B SLIP THRU THIMBLE ST IPS IWRC #1/8 1/4.42.37.84.73.59.42 3 6 W-2 5/16 IPS IWRC 3/16 3/8.70.61 1.4 1.2 1.0.70 3 6 W-2 7/16 IPS IWRC 1/4 1/2 1.2 1.1 2.5 2.1 1.7 1.2 4 8 W-3 9/16 IPS IWRC 5/16 5/8 1.9 1.7 3.8 3.3 2.7 1.9 4 8 W-4 3/4 IPS IWRC 3/8 3/4 2.8 2.4 5.5 4.8 3.9 2.8 5 10 W-4 7/8 IPS IWRC 7/16 7/8 3.7 3.3 7.5 6.5 5.3 3.7 6 12 W-5 7/8 IPS IWRC 1/2 1 4.8 4.2 9.7 8.4 6.8 4.8 6 12 W-5 1 IPS IWRC 9/16 1-1/8 6.1 5.3 12 11 8.6 6.1 7.5 15 W-6 1-1/8 IPS IWRC 5/8 1-1/4 7.5 6.6 15 13 11 7.5 9 18 W-6 1-1/4 IPS IWRC 3/4 1-1/2 11 9.4 22 19 15 11 10 20 W-7 1-3/8 IPS IWRC 7/8 1-3/4 15 13 29 25 21 15 12 24 W-9 1-7/8 IPS IWRC 1 2 19 17 38 33 27 19 15 30 W-9 2 # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. ** See Choker Hitch Rated Capacity Adjustment. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Sling angles less than 30 degrees shall not be used. HEAVY THIMBLE HT All capacities in tons of 2,000 lbs. All eye and fitting dimensions in inches. 43
MULTI-PART WIRE BODY 2-LEG CHOKERS 3-PART TWO-LEG WIRE CHOKERS SLING DIA. RATED CAPACITY ()* 2-LEG CHOKER HITCH SINGLE LEG CHOKER** 60º 45º 30º SLIP THRU CHOKER HOOK NUMBER D THIMBLE L W IPS IWRC #1/8 1/4 0.5.64.52.37 1/4 5/16 1/2 5 2-1/2 IPS IWRC 3/16 3/8 0.8 1.1.87.61 3/8 1/2 5 2-1/2 IPS IWRC 1/4 1/2 1.5 1.9 1.5 1.1 1/2 5/8 6 3 IPS IWRC 5/16 5/8 2.3 2.9 2.4 1.7 5/8 3/4 5-1/2 2-3/4 IPS IWRC 3/8 3/4 3.3 4.2 3.4 2.4 3/4 1 8 4 IPS IWRC 7/16 7/8 4.4 5.7 4.6 3.3 7/8 1 1 8 4 IPS IWRC 1/2 1 5.7 7.3 6.0 4.2 7/8 1 1 8 4 IPS IWRC 9/16 1-1/8 5.0 9.2 7.5 5.3 1-1/8 1-1/4 1 8 4 IPS IWRC 5/8 1-1/4 6.1 11 9.3 6.6 1-1/8 1-1/4 1 8 4 IPS IWRC 3/4 1-1/2 8.7 16 13 9.4 1-3/8 1-1/2 1-1/2 12 4 # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. ** See Choker Hitch Rated Capacity Adjustment. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Sling angles less than 30 degrees shall not be used. All capacities in tons of 2,000 lbs. All eye and fitting dimensions in inches. 44
MULTI-PART WIRE BODY 2-LEG SPREADERS HAND SPLICE MECHANICAL SPLICE 3-PART TWO-LEG WIRE BRIDLES ALLOY OBLONG LINK SLING RATED CAPACITY ()* DIA. 60º 45º 30º DIA. LENGTH WIDTH # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. **WORKING LOAD LIMIT HOOK ** TON E R IPS IWRC #1/8 1/4.73.59.42 1/2 5 2-1/2 3/4 15/16 3-7/32 IPS IWRC 3/16 3/8 1.2 1.0.70 1/2 5 2-1/2 1 1-1/32 3-21/32 IPS IWRC 1/4 1/2 2.1 1.7 1.2 3/4 5-1/2 2-3/4 2 1-7/32 4-11/16 IPS IWRC 5/16 5/8 3.3 2.7 1.9 1.0 8 4 3 1-1/2 5-3/4 IPS IWRC 3/8 3/4 4.8 3.9 2.8 1.0 8 4 5 1-7/8 7-3/8 IPS IWRC 7/16 7/8 6.5 5.3 3.7 1.0 8 4 7-1/2 2-1/4 9-1/16 IPS IWRC 1/2 1 8.4 6.8 4.8 1-1/4 8-3/4 4-3/8 7-1/2 2-1/4 9-1/16 IPS IWRC 9/16 1-1/8 11 8.6 6.1 1 8 4 7-1/2 2-1/4 9-1/16 IPS IWRC 5/8 1-1/4 13 11 7.5 1-1/4 8-3/4 4-3/8 7-1/2 2-1/4 9-1/16 IPS IWRC 3/4 1-1/2 19 15 11 1-1/2 12 6 10 2-1/2 10-1/16 IPS IWRC 7/8 1-3/4 25 21 15 1-3/4 12 6 15 3-3/8 12-1/2 IPS IWRC 1 2 33 27 19 2 14 7 20 4 14-1/16 LATCH KITS ARE AVAILABLE IF REQUIRED. All capacities in tons of 2,000 lbs. All eye and fitting dimensions in inches. 45
BRAIDED WIRE BODY SINGLE LEG SLINGS FLAT BRAID IPS IWRC 6-PART WIDTH OF BODY THICKNESS OF BODY RATED CAPACITY ()* BASKET HITCH CHOKER EYE HITCH** 60º 45º 30º A B SLIP THRU THIMBLE ST # 3/32 7/16 1/4 0.42 0.37 0.84 0.73 0.59 0.42 2 4 W-2 1/4 # 1/8 9/16 3/8 0.84 0.74 1.7 1.5 1.2 0.84 3 6 W-2 5/16 # 3/16 13/16 1/2 1.4 1.2 2.8 2.4 2.0 1.4 4 8 W-3 1/2 # 1/4 1-1/8 11/16 2.5 2.2 4.9 4.3 3.5 2.5 5 10 W-4 5/8 # 5/16 1-3/8 7/8 3.8 3.4 7.7 6.7 5.4 3.8 6 12 W-4 3/4 # 3/8 1-11/16 1 5.5 4.8 11.0 9.5 7.8 5.5 7 14 W-5 7/8 7/16 2 1-3/16 7.5 6.5 15.0 13.0 11.0 7.5 8 16 W-5 1 1/2 2-1/4 1-5/16 9.7 8.5 19.0 17.0 14.0 9.7 9 18 W-6 1-1/8 9/16 2-1/2 1-1/2 12.0 11.0 24.0 21.0 17.0 12.0 10 20 W-6 1-3/8 5/8 2-13/16 1-11/16 15.0 13.0 30.0 26.0 21.0 15.0 11 22 W-7 1-1/2 3/4 3-3/8 2 22.0 19.0 43.0 37.0 30.0 22.0 12 24 W-8 1-5/8 7/8 4 2-5/16 29.0 25.0 58.0 50.0 41.0 29.0 14 28 W-9 2 1 4-1/2 2-11/16 38.0 33.0 75.0 65.0 53.0 38.0 16 32 W-10 # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. ** See Choker Hitch Rated Capacity Adjustment. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Sling angles less than 30 degrees shall not be used. HEAVY THIMBLE HT ALL CAPACITIES IN OF 2,000 LBS. ALL EYE AND FITTING DIMENSIONS IN INCHES. 46
BRAIDED WIRE BODY 2 LEG CHOKERS 6-PART BRAIDED WIRE BODY 2 LEG SPREADERS IPS IWRC RATED CAPACITY ()* 2 LEG CHOKER HITCH ALLOY OBLONG LINK SINGLE LEG CHOKER** 60º 45º 30º D L W # 3/32 0.37 0.64 0.52 0.37 1/2 5 2-1/2 0 # 1/8 0.74 1.3 1.04 0.74 1/2 5 2-1/2 1 # 3/16 1.2 2.1 1.7 1.2 1/2 5 2-1/2 2 # 1/4 2.2 3.7 3.1 2.2 3/4 5-1/2 2-3/4 4 # 5/16 3.4 5.8 4.8 3.4 1 8 4 5 # 3/8 4.8 8.4 6.8 4.8 1 8 4 6 7/16 6.5 11.0 9.2 6.5 1-1/4 8-3/4 4-3/8 7 1/2 8.5 15.0 12.0 8.5 1-1/4 8-3/4 4-3/8 8 9/16 11.0 18.0 15.0 11.0 1-1/2 12 6 8 HOOK NO. LENGTH IPS IWRC 6-PART RATED CAPACITY ()* ALLOY OBLONG LINK 60º 45º 30º D L W WWL ** E # 3/32 0.73 0.59 0.42 1/2 5 2-1/2 3/4 15/16 3-7/32 # 1/8 1.5 1.2 0.84 1/2 5 2-1/2 1 1-1/32 3-21/32 # 3/16 2.4 2.0 1.4 5/8 6 3 1-1/2 1-1/16 4-3/32 # 1/4 4.3 3.5 2.5 3/4 5-1/2 2-3/4 3 1-1/2 5-3/4 # 5/16 6.7 5.4 3.8 1 8 4 5 1-7/8 7-3/8 # 3/8 9.5 7.8 5.5 1 8 4 7-1/2 2-1/4 9-1/16 7/16 13.0 11.0 7.5 1-1/4 8-3/4 4-3/8 7-1/2 2-1/4 9-1/16 1/2 17.0 14.0 9.7 1-1/2 12 6 10 2-1/4 10-1/16 9/16 21.0 17.0 12.0 1-1/2 12 6 15 3-3/8 12-1/2 5/8 26.0 21.0 15.0 1-3/4 12 6 20 4 14-1/16 3/4 37.0 30.0 22.0 2 14 7 25 4-1/4 18-5/16 7/8 50.0 41.0 29.0 2-1/4 16 8 AH-37 4-1/4 18-3/16 LATCH KITS ARE AVAILABLE IF REQUIRED. # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. ** See Choker Hitch Rated Capacity Adjustment. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Sling angles less than 30 degrees shall not be used. All capacities in tons of 2,000 lbs. All eye and fitting dimensions in inches. HOOK R 47
BRAIDED WIRE BODY SINGLE LEG SLINGS ROUND BRAID IPS IWRC 8-PART SLING RATED CAPACITY ()* BASKET HITCH CHOKER HITCH** 60º 45º 30º A EYE B SLIP THRU THIMBLE ST # 3/32 7/16.56 0.49 1.1 0.97 0.79 0.56 2 4 W-2 5/16 # 1/8 9/16 1.1 1.0 2.2 1.9 1.6 1.1 3 6 W-2 3/8 # 3/16 13/16 1.9 1.6 3.7 3.2 2.6 1.9 4 8 W-3 1/2 # 1/4 1-1/8 3.3 2.9 6.6 5.7 4.7 3.3 5 10 W-4 3/4 # 5/16 1-3/8 5.1 4.5 10.0 8.9 7.3 5.1 6 12 W-5 1 # 3/8 1-11/16 7.3 6.4 15.0 13.0 10.0 7.3 7 14 W-5 1-1/8 7/16 2 10.0 8.7 20.0 17.0 14.0 10.0 8 16 W-6 1-1/4 1/2 2-1/4 13.0 11.0 26.0 22.0 18.0 13.0 9 18 W-7 1-3/8 9/16 2-1/2 16.0 14.0 32.0 28.0 23.0 16.0 10 20 W-7 1-1/2 5/8 2-13/16 20.0 18.0 40.0 35.0 28.0 20.0 11 22 W-8 1-3/4 3/4 3-3/8 29.0 25.0 57.0 50.0 41.0 29.0 12 24 W-9 2 7/8 4 39.0 34.0 78.0 67.0 55.0 39.0 14 28 W-10 1 4-1/2 50.0 44.0 101.0 87.0 71.0 50.0 16 32 W-10 # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. ** See Choker Hitch Rated Capacity Adjustment. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Sling angles less than 30 degrees shall not be used. HEAVY THIMBLE HT All capacities in tons of 2,000 lbs. All eye and fitting dimensions in inches. 48
BRAIDED WIRE BODY 2 LEG CHOKERS DT-8P2 IPS IWRC 8-PART RATED CAPACITY ()* 2 LEG CHOKER HITCH ALLOY OBLONG LINK SINGLE LEG CHOKER** 60º 45º 30º D L W # 3/32 0.49 0.85 0.69 0.49 1/2 5 2-1/2 0 # 1/8 0.98 1.7 1.4 0.98 1/2 5 2-1/2 1 # 3/16 1.6 2.8 2.3 1.6 3/4 6 3 2 # 1/4 2.9 5.0 4.1 2.9 1 8 4 4 # 5/16 4.5 7.8 6.3 4.5 1 8 4 5 # 3/8 6.4 11.0 9.1 6.4 1-1/4 8 4 6 7/16 8.7 15.0 12.0 8.7 1-1/2 12 6 7 1/2 11.0 20.0 16.0 11.0 1-1/2 12 6 8 # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. ** See Choker Hitch Rated Capacity Adjustment. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Sling angles less than 30 degrees shall not be used. HOOK NO. All capacities in tons of 2,000 lbs. All eye and fitting dimensions in inches. 49
BRAIDED WIRE BODY 2-LEG SPREADERS LENGTH IPS IWRC 8-PART RATED CAPACITY ()* ALLOY OBLONG LINK 60º 45º 30º D L W # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. ** See Choker Hitch Rated Capacity Adjustment. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Sling angles less than 30 degrees shall not be used. HOOK WWL ** E R # 3/32 0.97 0.79 0.56 1/2 5 2-1/2 3/4 15/16 3-7/32 # 1/8 1.9 1.6 1.1 1/2 5 2-1/2 1-1/2 1-1/16 4-3/32 # 3/16 3.2 2.6 1.9 3/4 5-1/2 2-3/4 3 1-1/2 5-3/4 # 1/4 5.7 4.7 3.3 1 8 4 5 1-7/8 7-3/8 # 5/16 8.9 7.3 5.1 1 8 4 AH-7 1-7/8 7-3/8 # 3/8 13.0 10.0 7.3 1-1/4 8-3/4 4-3/8 10 2-1/2 10-1/16 7/16 17.0 14.0 10.0 1-1/2 12 4-3/8 15 3-3/8 12-1/2 1/2 22.0 18.0 13.0 1-3/4 12 6 15 3-3/8 12-1/2 9/16 28.0 23.0 16.0 2 14 6 20 4 14-1/16 5/8 35.0 28.0 20.0 2 14 7 25 4-1/4 18-5/16 3/4 50.0 41.0 29.0 2-1/4 16 8 AH-37 4-1/4 18-15/16 LATCH KITS ARE AVAILABLE IF REQUIRED. All capacities in tons of 2,000 lbs. All eye and fitting dimensions in inches. 50
MULTI-PART BODY SINGLE LEG MECHANICAL SPLICE 9-PART RATED CAPACITY ()* BASKET HITCH EYE DIMENSIONS CHOKER HITCH** 60º 45º 30º A B SLIP THRU THIMBLE ST # 1/4 3.7 3.2 7.4 6.4 5.2 3.7 3 6 W-2 1/4 # 3/8 8.3 7.2 17 14 12 8.3 3 6 W-2 3/8 1/2 14 13 29 25 20 14 4 8 W-3 1/2 5/8 23 20 45 39 32 23 5 10 W-4 5/8 3/4 32 28 65 56 46 32 6 12 W-4 3/4 7/8 44 38 87 76 62 44 6-1/2 13 W-5 7/8 1 57 50 113 98 80 57 7 14 W-5 1 1-1/4 87 77 175 151 124 87 8 16 W-6 1-1/4 1-1/2 125 109 249 216 176 125 9 18 W-7 1-1/2 1-3/4 168 147 335 290 237 168 10 20 W-8 1-3/4 2 217 190 433 375 306 217 12 24 W-9 2 # Made with 7 x 19 Galvanized component rope. * Rated Capacities Basket Hitch based on D/d ratio of 25 times the component rope diameter. ** See Choker Hitch Rated Capacity Adjustment. Rated Capacities based on pin diameter no larger than natural eye width or less than the nominal sling diameter. Sling angles less than 30 degrees shall not be used. HEAVY THIMBLE HT All capacities in tons of 2,000 lbs. All eye and fitting dimensions in inches. 51
GROMMETS/STRAND LAID/MECHANICAL SPLICE EXTRA IMPROVED PLOW STEEL 6 x 19 or 6 X 37 classification IWRC Rated capacities in tons LENGTH CHOKER BASKET 60º 45º 30º 1/4 1.1.74 2.1 1.8 1.5 1.1 5/16 1.6 1.2 3.3 2.8 2.3 1.6 3/8 2.4 1.6 4.7 4.1 3.3 2.4 7/16 3.2 2.2 6.4 5.5 4.5 3.2 1/2 4.1 2.9 8.3 7.2 5.9 4.1 9/16 5.2 3.7 10 9.1 7.4 5.2 5/8 6.4 4.5 13 11 9.1 6.4 3/4 9.2 6.4 18 16 13 9.2 7/8 12 8.7 25 22 18 12 1 16 11 32 28 23 16 1-1/8 20 14 41 35 29 20 1-1/4 25 17 50 43 35 25 1-3/8 30 21 60 52 42 30 1-1/2 36 25 71 62 50 36 1-5/8 41 29 82 71 58 41 1-3/4 48 33 95 83 68 48 1-7/8 54 38 109 94 77 54 2 62 43 124 107 87 62 2-1/8 69 48 138 119 98 69 2-1/4 77 54 154 133 109 77 2-3/8 85 60 171 148 121 85 2-1/2 94 66 188 163 133 94 2-5/8 103 72 207 179 146 103 2-3/4 113 79 225 195 159 113 2-7/8 122 86 245 212 173 122 3 133 93 265 230 188 133 LENGTH Rated Capacities Basket Hitch based on D/d ratio of 5 where "d" = diameter of the finished grommet. Rated Capacities based on pin diameter no smaller than 5 times the body diameter. Horizontal Sling angles less than 30 degrees shall not be used. Note: Min. length is 96 times the rope diameter. 52
CUSTOM SOCKET ASSEMBLIES Wire Rope assemblies with fittings permanently attached at ends are custom fabricated for use as boom pendants, guylines, raising lines, backstays, lifting spreaders, etc. These are offered in both poured, or spelter, sockets and mechanically swaged sockets. A Design Factor of five is applied in establishing Rated Capacities shown. EPOXY COMPOUND SPELTER SOCKET Epoxy compound is standard as the bonding medium surrounding wires inside the socket. Steel forgings are used for rope sizes 1/2" through 1-1/2", and cast steel fittings for larger sizes. Larger than 4" available on special order. Assembly length is measured from centerline of pin for open sockets and bearing point for closed sockets. OS-OS Same Plane Opposite Plane CS-CS Same Plane Opposite Plane OS-CS Same Plane Opposite Plane LENGTH 1/2 2.7 4.9 9/16 3.4 6.2 5/8 4.1 7.6 3/4 5.9 11 7/8 8 15 1 10 19 1-1/8 13 24 1-1/4 16 30 1-3/8 19 36 1-1/2 23 42 1-5/8 26 49 1-3/4 31 57 1-7/8 35 64 2 40 73 2-1/8 44 82 2-1/4 49 91 2-3/8 55 101 2-1/2 60 112 2-5/8 66 122 2-3/4 72 134 2-7/8 78 145 3 85 157 3-1/8 92 169 3-1/4 98 182 3-3/8 106 196 3-1/2 113 209 BASKET 53
CUSTOM SOCKET ASSEMBLIES Indicate choice of end fittings on purchase orders by the suffixes OS or CS after the stock number, for open or closed type fittings. Pins and cotters are supplied as standard on open fittings, but assemblies may be specified without pins. Fittings will be assembled in the same plane unless specified otherwise on the order. SWAGED SOCKET In mechanically swaged fittings, high pressure presses and precision dies cause metal of the socket to flow around wires and strands to offer the ultimate in compactness and strength with minimum weight. Material is weldless, dropforged steel. Normally, only regular lay rope is used. Swaged assemblies are interchangeable with poured sockets up through 2" rope diameters. Assembly length is measured from centerline of pins for both open and closed sockets. OS-OS Same Plane Opposite Plane CS-CS Same Plane Opposite Plane OS-CS Same Plane Opposite Plane RATED CAPACITY ()* 6 X 19 & 6 X 37 IWRC XIP 1/4.69 5/16 1.05 3/8 1.5 7/16 2.04 1/2 2.66 9/16 3.36 5/8 4.12 3/4 5.88 7/8 7.96 1 10.34 1-1/8 13.0 1-1/4 15.98 1-3/8 19.2 1-1/2 22.8 1-3/4 30.6 2 39.6 2-1/4 49.4 2-1/2 60.4 LENGTH 54
TUFFY TRI-BRAID SLINGS TUFF AND FLEXIBLE SLINGS, FOR YOUR TOUGHEST, MOST DEMANDING LOADS Unmatched Flexibility The unique 3x3 strand design of all Tuffy tri-braid slings consists of a patented machine-braided wire fabric with interlaced construction, resulting in flexibility and abrasion resistance far superior to standard rope strands. Made of industrialgrade steel and constructed with the highest quality standards, only Tuffy slings possess the perfect balance of strength, flexibility and durability. Longer Service Life Because machine braiding produces proper balancing of all parts, the outcome is a highly efficient sling with a much longer service life. Even if one of the braided parts is cut or broken, there is no stranding. Durable and reliable, Tuffy tri-braid slings perform to unprecedented standards, keeping working environments more productive and effective. Quicker and Easier Loading Workers now have an easy-to-handle tool that significantly eases and speeds the hitching and unhitching process. Tuffy's flexibility enables greater sling control, and the unique construction yields a safer, more secure sling, significantly less prone to dangerous recoils and breakage. Complete Knot and Kink Resistance Tuffy Tri-braid slings are virtually impervious to kinking and knotting due to the machine-braided and interlaced construction. Nothing short of a vice can leave a mark on a Tuffy sling, and even then the ridge simply straightens out with no material damage. Where a standard sling's strength can be canceled out if stiffness imposes abnormal fatigue which saps the sling's endurance, the flexibility and balance built into every tri-braid sling renders this issue obsolete. 55
T-1 TRI-BRAID SLING SINGLE PLY Standard Eye/Eye Sling Single Leg Application: General purpose sling for straight or basket hitches. EYE SIZE BASKET BASKET 60 BASKET 45 BASKET 30 1/4 3x6 0.45 0.9 0.78 0.64 0.45 3/8 3x6 0.95 1.9 1.6 1.3 0.95 1/2 4x8 1.7 3.4 2.9 2.4 1.7 5/8 5x10 2.6 5.2 4.5 3.7 2.6 3/4 6x12 3.7 7.4 6.4 5.2 3.7 7/8 6.5x13 5 10 8.7 7.1 5 1 7x14 6.3 13 11 8.9 6.3 1-1/4 8x16 9 18 16 13 9 1-1/2 9x18 12 24 21 17 12 1-3/4 10x20 15 30 26 21 15 2 12x24 20 40 35 28 20 T-2 TRI-BRAID SLING SINGLE PLY Single Leg - With Sliding Choker Hook and Thimble Bottom Application: Pipe, bundles, bars, castings, lumber - any type of load that can utilize a choker hook. EYE SIZE GALV. THIMBLE (1 EA.) SLIDING CHOKER HOOK (1 EA.) 1/4 3x6 1/4 1/4 0.34 3/8 3x6 3/8 3/8 0.71 1/2 4x8 1/2 1/2 1.3 5/8 5x10 5/8 5/8 2.0 3/4 6x12 3/4 3/4 2.8 7/8 6.5x13 7/8 7/8 3.8 1 7x14 1 1 4.7 1-1/4 8x16 1-1/4 1-1/4 6.8 1-1/2 9x18 1-1/2 1-1/2 9.0 CHOKER 56
T-3D TRI-BRAID SLING DOUBLE PLY Single Leg - Two Parts (2 ply) Spliced Together Side-by-Side Application: When higher capacity are needed (2 ply) such as for locomotives, generators, pressure vessels, etc. EYE SIZE CHOKER 1/4 3x6 0.90 0.68 1.80 3/8 4x8 1.90 1.4 3.8 1/2 5x10 3.4 2.6 6.8 5/8 6x12 4.7 3.5 9.4 3/4 7x14 6.7 5.0 13.0 7/8 8x16 9.0 6.8 18.0 1 8x16 11.0 8.5 23.0 1-1/4 9x18 16.0 12.0 32.0 1-1/2 10x20 22.0 17.0 43.0 BASKET 1-3/4 11x22 27.0 20.0 54.0 T-4D TRI-BRAID SLING DOUBLE PLY Single Leg - Top eye 2-parts Spliced Together with Double Ply Body with Sliding Choker Hook and Thimble Bottom Application: When higher capacity are needed. More flexibility is provided for choking smaller diameter loads. EYE SIZE SLIDING CHOKER HOOK (1 EA.) GALVANIZED THIMBLE (1 EA.) 1/4 3x6 3/8" 1/4 0.68 3/8 4x8 #2 3/8 1.4 1/2 5x10 #4 1/2 2.6 5/8 6x12 #5 5/8 3.5 3/4 7x14 #5 3/4 5.0 7/8 8x16 #6 7/8 6.8 1 8x16 #7 1 8.5 1-1/4 9x18 #8 1-1/4 12.0 CHOKER 57
T-5 TRI-BRAID SLING DOUBLE PLY Single Leg - 2 Side-by-Side Parts with Crescent Thimble in Bottom Loop Application: Gives move stability than single part for handling such loads as tanks, coils, castings, barrels and boxes. EYE SIZE CRESCENT THIMBLE (1 EA.) 1/4 3x6 6C 0.68 3/8 4x8 6C 1.4 1/2 5x10 8C 2.6 5/8 6x12 9C 3.9 3/4 7x14 10C 5.6 7/8 8x16 14C 7.5 1 8x16 16C 9.5 T-6 TRI-BRAID SLING SINGLE PLY CHOKER 1-1/4 9x18 20C 14.0 2-Leg Bridle Sling with Equalizing Thimble Top and Hooks Bottom Application: For oddly shaped loads - high one end, low other - legs adjust and equalize. EYE SIZE EQUALIZING THIMBLE (1 EA.) ALLOY EYE HOOK (2 EA.) 60 45 30 1/4 3x6 3E 1 Ton 0.9 0.78 0.64 0.45 3/8 3x6 3E 1.5 Ton 1.9 1.6 1.3 0.95 1/2 4x8 4E 3 Ton 3.4 2.9 2.4 1.7 5/8 5x10 6E 5 Ton 5.2 4.5 3.7 2.6 3/4 6x12 6E 5 Ton 7.4 6.4 5.2 3.7 7/8 6.5x13 8E 7 Ton 10.0 8.7 7.1 5.0 1 7x14 8E 11 Ton 13.0 11.0 8.9 6.3 1-1/4 8x16 10E 15 Ton 18.0 16.0 13.0 9.0 1-1/2 9x18 12E 15 Ton 24.0 21.0 17.0 12.0 1-3/4 10x20 14E 22 Ton 30.0 26.0 21.0 15.0 2 12x24 16E 30 Ton 40.0 35.0 28.0 20.0 58
T-7D TRI-BRAID SLING DOUBLE PLY 2-Leg Bridle Sling - Double Ply with Link Top and Hooks with Thimbles Bottom Application: When higher capacities are needed. EYE SIZE (IN.) GALVANIZED THIMBLE (2 EA.) (IN.) MASTERLINK(O) OR PEARLINK(P) (1 EA.) ALLOY EYE HOOK (2 EA.) 60 45 1/4 3x6 1/4 5/8 P 1.5 Ton 1.8 1.60 1.30 0.90 3/8 4x8 3/8 7/8 P 3 Ton 3.8 3.3 2.7 1.90 1/2 5x10 1/2 1-1/4 P 5 Ton 6.8 5.9 4.8 3.4 5/8 6x12 5/8 1-1/4 O 7 Ton 9.4 8.1 6.6 4.7 3/4 7x14 3/4 1-1/2 O 11 Ton 13.0 12.0 9.4 6.7 7/8 8x16 7/8 1-3/4 O 15 Ton 18.0 16.0 13.0 9.0 1 8x16 1 1-3/4 O 15 Ton 23.0 20.0 16.0 11.0 1-1/4 9x18 1-1/4 2-1/8 O 30 Ton 32.0 28.0 23.0 16.0 1-1/2 10x20 1-1/2 2-1/2 O 37 Ton 43.0 37.0 31.0 22.0 1-3/4 11x22 1-3/4 2-3/4 O 45 Ton 54.0 47.0 38.0 27.0 T-8 TRI-BRAID SLING SINGLE PLY 2-Leg Bridle Sling with Link Top and Sliding Choker Hooks with Thimbles Bottom Application: Helps eliminate load rotation and is better suited for handling pipe, bars, timber, tanks, castings and other loads which run in long lengths. 30 EYE SIZE (IN.) GALVANIZED THIMBLE (2 EA.) MASTERLINK(O) OR PEARLINK(P) (1 EA.) SLIDING CHOKER HK (2EA.) 60 45 1/4 3x6 1/4 1/2 P 1/4 0.68 0.58 0.48 0.34 3/8 3x6 3/8 1/2 P 3/8 1.40 1.2 1.0 0.71 1/2 4x8 1/2 3/4 P 1/2 2.6 2.2 1.8 1.3 5/8 5x10 5/8 7/8 P 5/8 3.9 3.4 2.8 2.0 3/4 6x12 3/4 1-1/4 P 3/4 5.6 4.8 3.9 2.8 7/8 6.5x13 7/8 1-1/4 P 7/8 7.5 6.5 5.3 3.8 1 7x14 1 1-1/4 O 1 9.5 8.2 6.7 4.7 1-1/4 8x16 1-1/4 1-1/2 O 1-1/4 14.0 12.0 9.5 6.8 1-1/2 9x18 1-1/2 1-3/4 O 1-1/2 18.0 16.0 13.0 9.0 30 59
T-9 TRI-BRAID SLING SINGLE PLY 2-Leg Double Loop Bridle Sling Link Top and No Hooks Application: Well suited for handling sheet steel, bar stock, lumber, structural shapes, flasks and castings. EYE SIZE MASTERLINK(O) OR PEARLINK(P) (1 EA.) 60 45 1/4 3x6 5/8 P 1.8 1.6 1.3 0.9 3/8 3x6 7/8 P 3.8 3.3 2.7 1.9 1/2 4x8 1-1/4 P 6.8 5.9 4.8 3.4 5/8 5x10 1-3/8 O 10.0 9.0 7.4 5.2 3/4 6x12 1-1/2 O 15.0 13.0 10.0 7.4 30 7/8 6.5x13 1-3/4 O 20.0 17.0 14.0 10.0 1 7x14 1-7/8 O 25.0 22.0 18.0 13.0 1-1/4 8x16 2-1/4 O 36.0 31.0 25.0 18.0 1-1/2 9x18 2-1/2 O 48.0 42.0 34.0 24.0 1-3/4 10x20 2-3/4 O 60.0 52.0 42.0 30.0 2 12x24 3-1/4 O 80.0 69.0 57.0 40.0 T-12 TRI-BRAID SLING SINGLE PLY Standard 2-Leg Bridle Sling Link Top/Hooks Bottom Application: Lifting machinery, castings, motors and aircraft assemblies. EYE SIZE ALLOY EYE HOOK (2 EA.)(IN.) MASTERLINK(O) OR PEARLINK(P) (1 EA.) 60 45 30 1/4 3x6 1 Ton 1/2 P 0.90 0.78 0.64 0.45 3/8 3x6 1.5 Ton 5/8 P 1.90 1.6 1.3 0.95 1/2 4x8 3 Ton 7/8 P 3.4 2.9 2.4 1.7 5/8 5x10 5 Ton 1 P 5.2 4.5 3.7 2.6 3/4 6x12 5 Ton 1-1/4 P 7.4 6.4 5.2 3.7 7/8 6.5x13 7 Ton 1-1/4 O 10.0 8.7 7.1 5.0 1 7x14 11 Ton 1-1/2 O 13.0 11.0 8.9 6.3 1-1/4 8x16 15 Ton 1-3/4 O 18.0 16.0 13.0 9.0 1-1/2 9x18 15 Ton 1-7/8 O 24.0 21.0 17.0 12.0 1-3/4 10x20 22 Ton 2 O 30.0 26.0 21.0 15.0 2 12x24 30 Ton 2-1/2 O 40.0 35.0 28.0 20.0 60
T-13 TRI-BRAID SLING SINGLE PLY Standard 3-Leg Bridle Sling Link Top/Hooks Bottom Application: Lifting dies, castings and assemblies which must be placed carefully, sometimes in difficult locations. EYE SIZE ALLOY EYE HOOK (3 EA.) MASTERLINK(O) OR PEARLINK(P) (1 EA.) 60 45 30 1/4 3x6 1 Ton 5/8 P 1.40 1.20 0.95 0.68 3/8 3x6 1.5 Ton 3/4 P 2.90 2.5 2.0 1.40 1/2 4x8 3 Ton 1 P 5.1 4.4 3.6 2.6 5/8 5x10 5 Ton 1-1/4 P 7.8 6.8 5.5 3.9 3/4 6x12 5 Ton 1-1/4 O 11.0 9.6 7.8 5.6 7/8 6.5x13 7 Ton 1-1/2 O 15.0 13.0 11.0 7.5 1 7x14 11 Ton 1-3/4 O 19.0 16.0 13.0 9.5 1-1/4 8x16 15 Ton 1-7/8 O 27.0 23.0 19.0 14.0 1-1/2 9x18 15 Ton 2-1/4 O 36.0 31.0 25.0 18.0 1-3/4 10x20 22 Ton 2-1/2 O 45.0 39.0 32.0 23.0 2 12x24 30 Ton 2-3/4 O 60.0 52.0 42.0 30.0 T-14 TRI-BRAID SLING SINGLE PLY Standard 4-Leg Bridle Sling Link Top/Hooks Bottom Application: Use when extra stamina is needed for heavy, bulky loads such as ship sections, planer beds, founders molds, pressure vessels, etc. EYE SIZE ALLOY EYE HOOK (4 EA.) MASTERLINK(O) OR PEARLINK(P) (1 EA.) 60 45 1/4 3x6 1 Ton 5/8 P 1.80 1.60 1.30 0.90 3/8 3x6 1.5 Ton 7/8 P 3.80 3.3 2.7 1.90 1/2 4x8 3 Ton 1-1/4 P 6.8 5.9 4.8 3.4 5/8 5x10 5 Ton 1-3/8 O 10.0 9.0 7.4 5.2 3/4 6x12 5 Ton 1-1/2 O 15.0 13.0 10.0 7.4 7/8 6.5x13 7 Ton 1-3/4 O 20.0 17.0 14.0 10.0 1 7x14 11 Ton 1-7/8 O 25.0 22.0 18.0 13.0 1-1/4 8x16 15 Ton 2-1/4 O 36.0 31.0 25.0 18.0 1-1/2 9x18 15 Ton 2-1/2 O 48.0 42.0 34.0 24.0 1-3/4 10x20 22 Ton 2-3/4 O 60.0 52.0 42.0 30.0 2 12x24 30 Ton 3-1/4 O 80.0 69.0 57.0 40.0 30 61