ELECTROFOK MACHINE ELEKTROFOK (MICRO FIBER OPTIC CABLE BLOWING MACHINE with ELECTRIC)
GENERAL DESCRIPTION ELEKTROFOK is designed and produced with feedbacks from users who has specialty on cable blowing technologies. Elektrofok is using to blow cables from 1mm to 5 mm. You need to give us duct diameters in your project before ordering machine. Machine consists on four parts as you can see in figure 1. *Cable blowing group is blowing cable in duct with controlling byelectric panel. *You can control cable blowing speed and direction. *You can see the distance of cable you blowed from electric panel. *The most important thing of machine is sensor design which prevents breaking of cable. Machine stops before breaking of cable. *Air regulater system is setting air pressure in duct and also you can open,close air. *You can put machine on desired place and height with high quality tripod table. 2) Electric Panel Group 1) Cable Blowing Group 3) Air Regulater Group Elektrofok Control Needed electricity Needed air Cable blowing speed Dimensions of machine Dimensions of box Weight of machine with box = Micro fiber optic cable blowing machine with electric. = Technician. = City electric. = 15 bar -1 metercup/minute (NOTE=It can be changed to the different factors) = 0 to 50 meter/minute = 30 cm * 40cm * 15cm = 71 cm * 45cm * 42cm = 28 kg 4)Tripod Table Figure-1 1)USING CABLE BLOWING GROUP 1-A)MONTAGING DUCT,NUTRINGS AND O-RINGS Duct Montaging = Push the duct to the barrier (part 1 on figure 2) then turn part 2 to fix duct between part 3 and 4 as in the figure 2-a. 1 Montaging Nutring = The part 6 in figure 2-b is nutring.when you montage nutring, air canals of nutring must be on the direction of duct. Nutrings must be cutted from to take cable out from the nutring.when you montage nutring, cutted place must be on the underside to prevent air leaks. 4 3 2 6 5 Montaging O-rings = Part 5 in figure 2-b is o-ring. O-rings is montaging between duct and nutring as in the figure 2-b.If you do not montage nutrings like that air leaks happens.you need to change nutrings after someuse to prevent air leaks. Figure-2-a Figure-2-b
5 1-B)MONTAGING FIBER OPTIC CABLE and ADJUSTING PRESSURE ON CABLE BETWEEN ROLLS 6 7 1-C) CHANGING THE RUBBERIZED WHEELS 8 Figure-3 Figure-4 Montage fiber optic cable on machine as in the figure 3 and then close machine s upper part by turning part 5.Fix clamps as in figure 4 to prevent air leaks.wheels presses on cable,pressure on cable can be easily setted by turning part 6. Figure-5 Figure-6 Fiber optic cable is driven by rubber wheels.rubber wheels can damage after some use. These wheels can easily remove and change with new one as shown in Figure-5 and Figure-6. First, number 7 bolts must be took out so upper and bottom covers will be removed. Then, number 8 bolts on the wheels must be took out. Lastly, both wheels should remove slowly and change with spare ones. 2) INSTRUCTIONS FOR USING CONTROL PANEL 8 9 10 11 -Fiber optic cable drive forward and back with switch 8. This switch moves the cable -Speed of cable can adjust with the help of switch 9. -When you start machine, speedof the cable must be fewer then % 50. After starting you can increase speed. -You can open and close the sensor from switch 11. - Switch 11 activates the sensor to not to break cable.gives the alarm lamb on number 10 before the cable breaks. -See the cable blowing meter on screen 12. 12 Figure-7
16 15 14 13 3) INSTRUCTIONS FOR USING AIR REGULATOR UNIT Air connection to the machine made on the number 13 quick connection part. Number 14 valve opens and closes air intake. Air pressure inside the HDPE duct can adjust with the number 15 regulator. Number 16 gauge shows duct air pressure. Minimum HDPE pipe pressure must be 10-12 bar. Figure-8 4 ) USINGTRIPOD 17 Machine is fixing or releasing on tripod by the part 17 on figure 10.Machine can easily prepare for blowing by the tripod.lenght of the tripod are adjustable and portable with special bag as in the figure 11. Figure-9 Figure-10 Figure-11