Logbook for recording of competence by the Aircraft Maintenance Technician Apprentices

Logbook for recording of competence by the Aircraft Maintenance Technician Apprentices This logbook has been compiled by the Trade Testing Board appointed in virtue of Article 40 of the Employment & Training Services Act of 1990 to assess the competencies of persons that participate in the Technician Apprenticeship Scheme in the calling of Aircraft Maintenance Technician; in conjunction with the Transport Malta Civil Aviation Directorate to aid the said apprentices comply with the practical training requirements laid out in Legal Notice 82 of 1990 and Legal Notice 41 of 2005. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 1

GENERAL This log book is split in three sections:- INTRODUCTION BASIC SKILLS RECORDING SHEETS MAINTENANCE EXPERIENCE RECORDING SHEETS ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 2

INTRODUCTION The apprentice shall fill up the personal details and list the assessors in the personal details page. The apprentice practical training is split in the: BASIC SKILLS TRAINING, and the MAINTENACE EXPERIENCE TRAINING. The Basic Skills Section is aimed to guide the apprentice acquire the basic skills required in the aircraft maintenance trade in line with civil aviation regulations and practices in Europe. The Maintenance experience training is aimed at acquiring the required practical maintenance experience or on-job training (OJT) for the successful completion of the apprenticeship in accordance with Maltese Legislation. The maintenance experience training may be accomplished at: An Approved Maintenance Organisation (Part-145, Part-M Subpart F), or An Aircraft Maintenance Organisation recognized by the Transport Malta Civil Aviation Directorate, or An organization recognized by the appointed Trade Testing Board. The employers providing on-the-job training shall endeavour to organize, manage and assess the basic skills training in its entirety in conjunction with the vocational educational institutions providing the theoretical and practical training. The Logging sheets have provisions for entering: Personal Data, Names of assessors and supervisors, Aircraft and Registration Marks, ATA Chapters, Practical Training/Tasks. Category (Category Column is associated with the (EC) No 2042/2003 Part-66 Aircraft Maintenance Licence categories and is only included for the benefit of the apprentices pursuing the obtainment of the Part-66 AML) The apprentice shall record the training carried out and the assessor shall verify this information and make the necessary remarks regarding the competency and level achieved by the apprentice. The apprentice and assessor shall ensure that he/she has obtained competency in all the relevant Basic Skills listed in this logbook during his/her training period. All entries shall be made in ink. The nature of the involvement in task or intervention should be specified (execution, assistance, control, supervision). A new entry would be sufficient per day to count for the work experience time interval requirement. The assessors for the Basic Skills Section needs to be so recognised by the Trade Testing Board. The assessor for the maintenance practical training shall be nominated by the maintenance training organisation or the maintenance organisation. When logging maintenance tasks carried out on in-service aircraft, the supervisor can sign for the task and assessor endorses the experience. The Assessor needs to make sure he/she carries out an evaluation of the work carried out and progress made by the apprentice. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 3

PERSONAL DETAILS Name of Apprentice: I.D. No: of Birth: Address: Photo Name of Apprenticeship Provider: Calling: Name of Vocational Educational Institution: of Apprenticeship Commencement: of Apprenticeship Completion: Assessors: Remarks from Assessor: Miscellaneous Information ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 4

BASIC SKILLS To be Accomplished during Basic Training ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 5

Basic Skills Category Assessor Health and Safety Awareness Hangar Practices Familiarisation A, B1, B2 A, B1, B2 Location of station numbers and other reference systems A, B1, B2 Use of Hand tools A, B1 Use of Power Tools B1 Identification of Materials A, B1, B2 Use of Measuring Equipment (Depth Gauge, micrometer Feeler/slip gauges, go, no-go gauges) A, B1 Remove/install Thread Insert A, B1 Drilling and Tapping (Fe, Al etc) B1 Reaming B1 Use of Maintenance Data (IPC, AMM, CMM, SRM, effectivity) A, B1, B2 Identification of Corrosion B1 Countersinking Familiarisation and use of standard tools B1 A, B1 Name of Apprentice: Signature of Apprentice: ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 6

Basic Skills Identification of standards and specs of nuts, bolts, washers, split-pins, rivets Competence in Wire locking of components and turnbuckles Category B1 A, B1, B2 Remarks/Comments Signature of Assessor Wire/ Cable Looming B1, B2 Identification of cables B1, B2 Familiarisation and Use of Cable Stripping devices B1, B2 Familiarisation with Crimping Tools commonly used B1, B2 Crimping B1, B2 Soldering B1, B2 Use of Heat Gun B1, B2 Splicing Techinques B1, B2 Use of Cable inserts B1, B2 Familiarisation and use of Multimeters B1, B2 Accomplishment of Resistance Checks B1, B2 Accomplishment of Continuity Checks B1, B2 Accomplishment of Bonding Checks B1, B2 Name of Apprentice: Signature of Apprentice: ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 7

Basic Skills Implementation of ESDS procedures Category A, B1, B2 Remarks/Comments Signature of Assessor Basic Skills in Sheetmetal (cutting, bending, deburring ) B1 Calculation of Bend Radii B1 Achieve an acceptable level of Riveting experience B1 Installation of oversize rivets B1 Fasteners Removal using dedicated tools B1 Corrosion Treatment of Al in accordance with SRM methods B1 Accomplish a doubler repair B1 Testing and repair of composite material B1 Dye Penetrant / Flourescent Penetrant Inspection B1 Removal and Installation of flexible hoses B1 Removal and Installation of rigid pipes B1 Familiarisation with Fuel Tank Safety A, B1, B2 Aircraft Towing and Taxying B1, B2 Name of Apprentice: Signature of Apprentice: ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 8

Section 3 MAINTENANCE EXPERIENCE/ON-THE-JOB TRAINING Accomplished on In-service aircraft Applicable to Basic Training / Training Practical Element / OJT The following activities are considered relevant for maintenance experience Servicing; s: Inspection; LOC Location Operational and Functional Testing; FOT Functional/Operational Test Troubleshooting; SGH Service and Ground Handling Repairing; R/I - Removal Installation Modifying; MEL Minimum Equipment List Changing Component; TS - Troubleshooting Supervising these activities; Releasing aircraft to service. Refer also to item 3.2 of Appendix III to Part-66 for Practical Element of Training Note: Last pages are blank. These pages can be used and reproduced for the recording of the maintenance experience not covered in the scope of the tasks listed in this section. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 9

ATA 05 TIME LIMITS / MAINTENANCE CHECKS A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 10

ATA 06 DIMENSIONS AND AREAS A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 11

ATA 07 LIFTING AND SHORING A/C /Engine Job Card/Task Ref. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 12

ATA 08 LEVELLING & WEIGHING A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 13

ATA 09 TOWING & TAXING A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 14

ATA 12 SERVICING A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 15

ATA18 VIBRATION AND NOISE ANALYSIS (HELICOPTERS ONLY) A/C /Engine B1.3 ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 16

ATA 21 AIR CONDITIONING A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 17

ATA 22 AUTO FLIGHT, Ref ATA/ SYSTEM ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 18

ATA 23 COMMUNICATION A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 19

ATA 24 ELECTRICAL POWER SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 20

ATA 25 CABIN EQUIPMENT/FURNISHINGS A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 21

ATA 26 FIRE/SMOKE PROTECTION A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 22

ATA 27 FLIGHT CONTROL SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 23

ATA 28 AIRCRAFT FUEL SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 24

ATA 29 HYDRAULIC POWER SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 25

ATA 30 ICE/RAIN DETECTION/PROTECTION SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 26

ATA 31 INDEPENDENT INSTRUMENT A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 27

ATA 32 LANDING GEAR A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 28

ATA 33 AIRCRAFT LIGHTING SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 29

ATA 34 NAVIGATION DATA SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 30

ATA 35 OXYGEN SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 31

ATA 36 PNEUMATIC SYSTEN A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 32

ATA 37 A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 33

ATA 38 WATER/WASTE SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 34

ATA 42 INTEGRATED MODULAR AVIONICS A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 35

ATA 44 CABIN SYSTEMS A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 36

ATA 45 CENTRAL MAINTENANCE COMPUTER A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 37

ATA 46 INFORMATION SYSTEMS A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 38

ATA 49 AUXILIARY POWER UNIT/SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 39

ATA 52 AIRCRAFT DOORS SECTION A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 40

ATA 53 FUSELAGE STRUCTURE A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 41

ATA 54 PYLON STRUCTURE SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 42

ATA 56 WINDOW/WINDSHIELD A/C /Engine Signature ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 43

ATA 57 WING STRUCTURE A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 44

ATA 61 PROPELLER & CONTROL A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 45

ATA 62 MAIN ROTOR A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 46

ATA 63 MAIN ROTOR DRIVE A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 47

ATA 64 TAIL ROTOR A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 48

ATA 67 ROTORCRAFT FLIGHT CONTROL A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 49

ATA 71 POWERPLANT A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 50

ATA 72 TURBINE/TURBOPROP ENGINE A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 51

ATA 73 ENGINE FUEL & CONTROL A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 52

ATA 74 ENGINE IGNITION SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 53

ATA 75 ENGINE BLEED AIR SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 54

ATA 76 ENGINE CONTROL SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 55

ATA 77 ENGINE INDICATING SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 56

ATA 78 ENGINE EXHAUST A/C /Engine Job Card/Task Ref. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 57

ATA 79 ENGINE OIL SYSTEM A/C /Engine Job Card/Task Ref. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 58

ATA 80 STARTER A/C /Engine Job Card/Task Ref. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 59

ATA 81 TURBOCHARGING SYSTEM A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 60

ATA 85 RECIPROCATING ENGINE A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 61

A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 62

A/C /Engine ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 63

APPENDIX II Aircraft Practical Experience and On-the-Job Training List of Tasks (in the case of Training practical element this list can be used in conjunction with the Table in 3.2 of Appendix III to Part-66) Time limits/maintenance checks 100 hour check (general aviation aircraft). B or C check (transport category aircraft). Assist carrying out a scheduled maintenance check i.a.w. AMM. Review aircraft maintenance log for correct completion. Review records for compliance with Airworthiness Directives. Review records for compliance with component life limits. Procedure for inspection following heavy landing. Procedure for inspection following lightning strike. Towing and Taxiing Prepare for aircraft towing. Tow aircraft. Be part of aircraft towing team. Dimensions/Areas Locate component(s) by zone/station number. Perform symmetry check. Parking and Mooring Tie down aircraft. Park, secure and cover aircraft. Position aircraft in maintenance dock. Secure rotor blades. Lifting and Shoring Assist in: Jack aircraft nose or tail wheel. Jack complete aircraft. Sling or trestle major component. Placards and Markings Check aircraft for correct placards. Check aircraft for correct markings. Levelling/Weighing Level aircraft. Weigh aircraft. Prepare weight and balance amendment. Check aircraft against equipment list. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 64

Servicing Refuel aircraft. Defuel aircraft. Carry out tank to tank fuel transfer. Check/adjust tire pressures. Check/replenish oil level. Check/replenish hydraulic fluid level. Check/replenish accumulator pressure. Charge pneumatic system. Grease aircraft. Connect ground power. Service toilet/potable water system. Perform preflight/daily check. Auto flight Install servos. Rig bridle cables. Replace controller. Replace amplifier. Replacement of the auto flight system LRUs in case of fly-by-wire aircraft. Check operation of auto-pilot. Check operation of auto-throttle/auto-thrust. Check operation of yaw damper. Check and adjust servo clutch. Perform autopilot gain adjustments. Perform mach trim functional check. Troubleshoot faulty system. Check autoland system. Check flight management systems. Check stability augmentation system. Vibration and Noise Analysis Analyse helicopter vibration problem. Analyse noise spectrum. Analyse engine vibration. Communications Replace VHF com unit. Replace HF com unit. Replace existing antenna. Replace static discharge wicks. Check operation of radios. Perform antenna VSWR check. Perform Selcal operational check. Perform operational check of passenger address system. Functionally check audio integrating system. Repair coaxial cable. Troubleshoot faulty system. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 65

Air Conditioning Replace combustion heater. Replace flow control valve. Replace outflow valve. Replace safety valve. Replace vapour cycle unit. Replace air cycle unit. Replace cabin blower. Replace heat exchanger. Replace pressurisation controller. Clean outflow valves. Deactivate/reactivate cargo isolation valve. Deactivate/reactivate avionics ventilation components. Check operation of air conditioning/heating system. Check operation of pressurisation system. Troubleshoot faulty system. Equipment/Furnishings Replace carpets. Replace crew seats. Replace passenger seats. Check inertia reels. Check seats/belts for security. Check emergency equipment. Check ELT for compliance with regulations. Repair toilet waste container. Remove and install ceiling and sidewall panels. Repair upholstery. Change cabin configuration. Replace cargo loading system actuator. Test cargo loading system. Replace escape slides/ropes. Electrical Power Charge lead/acid battery. Charge Ni-Cad battery. Check battery capacity. Deep-cycle Ni-Cad battery. Replace integrated drive/generator/alternator. Replace switches. Replace circuit breakers. Adjust voltage regulator. Change voltage regulator. Amend electrical load analysis report. Repair/replace electrical feeder cable. Troubleshoot faulty system. Perform functional check of integrated drive/generator/alternator. Perform functional check of voltage regulator. Perform functional check of emergency generation system. Fire protection Check fire bottle contents. Check/test operation of fire/smoke detection and warning system. Check cabin fire extinguisher contents. Check lavatory smoke detector system. Check cargo panel sealing. Install new fire bottle. Replace fire bottle squib. Troubleshoot faulty system. Inspect engine fire wire detection systems. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 66

Flight Controls Inspect primary flight controls and related components i.a.w. AMM. Extending/retracting flaps & slats. Replace horizontal stabiliser. Replace spoiler/lift damper. Replace elevator. Deactivation/reactivation of aileron servo control. Replace aileron. Replace rudder. Replace trim tabs. Install control cable and fittings. Replace slats. Replace flaps. Replace powered flying control unit. Replace flat actuator. Rig primary flight controls. Adjust trim tab. Adjust control cable tension. Check control range and direction of movement. Check for correct assembly and locking. Troubleshoot faulty system. Functional test of primary flight controls. Functional test of flap system. Operational test of the side stick assembly. Operational test of the THS. THS system wear check. Fuel Water drain system (operation). Replace booster pump. Replace fuel selector. Replace fuel tank cells. Replace/test fuel control valves. Replace magnetic fuel level indicators. Replace water drain valve. Check/calculate fuel contents manually. Check filters. Flow check system. Check calibration of fuel quantity gauges. Check operation feed/selectors. Check operation of fuel dump/jettison system. Fuel transfer between tanks. Pressure defuel. Pressure refuel (manual control). Deactivation/reactivation of the fuel valves (transfer defuel, X- feed, refuel). Troubleshoot faulty system. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 67

Hydraulics Replace engine-driven pump. Check/replace case drain filter. Replace standby pump. Replace hydraulic motor pump/generator. Replace accumulator. Check operation of shut off valve. Check filters/clog indicators. Check indicating systems. Perform functional checks. Pressurisation/depressurisation of the hydraulic system. Power Transfer Unit (PTU) operation. Replacement of PTU. Troubleshoot faulty system. Ice and rain protection Replace pump. Replace timer. Inspect repair propeller deice boot. Test propeller de-icing system. Inspect/test wing leading edge de-icer boot. Replace anti-ice/deice valve. Install wiper motor. Check operation of systems. Operational test of the pitot-probe ice protection. Operational test of the TAT ice protection. Operational test of the wing ice protection system. Assistance to the operational test of the engine air-intake ice protection (with engines operating). Troubleshoot faulty system. Indicating/recording systems Replace flight data recorder. Replace cockpit voice recorder. Replace clock. Replace master caution unit. Replace FDR. Perform FDR data retrieval. Troubleshoot faulty system. Implement ESDS procedures. Inspect for HIRF requirements. Start/stop EIS procedure. Bite test of the CFDIU. Ground scanning of the central warning system. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 68

Landing Gear Lights Build up wheel. Replace main wheel. Replace nose wheel. Replace steering actuator. Replace truck tilt actuator. Replace gear retraction actuator. Replace uplock/downlock assembly. Replace shimmy damper. Rig nose wheel steering. Functional test of the nose wheel steering system. Replace shock strut seals. Servicing of shock strut. Replace brake unit. Replace brake control valve. Bleed brakes. Replace brake fan. Test anti skid unit. Test gear retraction. Change bungees. Adjust micro switches/sensors. Charge struts with oil and air. Troubleshoot faulty system. Test auto-brake system. Replace rotorcraft skids. Replace rotorcraft skid shoes. Pack and check floats. Flotation equipment. Check/test emergency blowdown (emergency landing gear extension). Operational test of the landing gear doors. Repair/replace rotating beacon. Repair/replace landing lights. Repair/replace navigation lights. Repair/replace interior lights. Replace ice inspection lights. Repair/replace logo lights. Repair/replace emergency lighting system. Perform emergency lighting system checks. Troubleshoot faulty system. Navigation Calibrate magnetic direction indicator. Replace airspeed indicator. Replace altimeter. Replace air data computer. Replace VOR unit. Replace ADI. Replace HSI. Check pitot static system for leaks. Check operation of directional gyro. Functional check weather radar. Functional check doppler. Functional check TCAS. Functional check DME. Functional check ATC Transponder. Functional check flight director system. Functional check inertial nav system. Complete quadrantal error correction of ADF system. Update flight management system database. Check calibration of pitot static instruments. Check calibration of pressure altitude reporting system. Troubleshoot faulty system. Check marker systems. Compass replacement direct/indirect. Check Satcom. Check GPS. Test AVM. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 69

Oxygen Inspect on-board oxygen equipment. Purge and recharge oxygen system. Replace regulator. Replace oxygen generator. Test crew oxygen system. Perform auto oxygen system deployment check. Troubleshoot faulty system. Water/Waste Replace water pump. Replace tap. Replace toilet pump. Perform water heater functional check. Pneumatic systems Replace filter. Replace air shut off valve. Replace pressure regulating valve. Replace compressor. Recharge dessicator. Adjust regulator. Check for leaks. Troubleshoot faulty system. Central Maintenance System Retrieve data from CMU. Replace CMU. Perform Bite check. Troubleshoot faulty system. Inspect waste bin flap closure. Vacuum systems Inspect the vacuum system i.a.w. AMM. Replace vacuum pump. Check/replace filters. Adjust regulator. Troubleshoot faulty system. Structures Assessment of damage. Sheet metal repair. Fibre glass repair. Wooden repair. Fabric repair. Recover fabric control surface. Treat corrosion. Apply protective treatment. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 70

Doors Inspect passenger door i.a.w. AMM. Rig/adjust locking mechanism. Adjust air stair system. Check operation of emergency exits. Test door warning system. Troubleshoot faulty system. Remove and install passenger door i.a.w. AMM. Remove and install emergency exit i.a.w. AMM. Inspect cargo door i.a.w. AMM. Propeller Assemble prop after transportation. Replace propeller. Replace governor. Adjust governor. Perform static functional checks. Check operation during ground run. Check track. Check setting of micro switches. Assessment of blade damage i.a.w. AMM. Dynamically balance prop. Troubleshoot faulty system. Windows Replace windshield. Replace direct vision window. Replace cabin window. Repair transparency. Main Rotors Install rotor assembly. Replace blades. Replace damper assembly. Check track. Check static balance. Check dynamic balance. Troubleshoot. Wings Skin repair. Recover fabric wing. Replace tip. Replace rib. Replace integral fuel tank panel. Check incidence/rig. Rotor Drive Replace mast. Replace drive coupling. Replace clutch/freewheel unit. Replace drive belt. Install main gearbox. Overhaul main gearbox. Check gearbox chip detectors. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 71

Tail Rotors Install rotor assembly. Replace blades. Troubleshoot. Power Plant Build up ECU. Replace engine. Repair cooling baffles. Repair cowling. Adjust cowl flaps. Repair faulty wiring. Troubleshoot. Assist in dry motoring check. Assist in wet motoring check. Assist in engine start (manual mode). Tail Rotor Drive Replace bevel gearbox. Replace universal joints. Overhaul bevel gearbox. Install drive assembly. Check chip detectors. Check/install bearings and hangers. Check/service/assemble flexible couplings. Check alignment of drive shafts. Install and rig drive shafts. Piston Engines Remove/install reduction gear. Check crankshaft run-out. Check tappet clearance. Check compression. Extract broken stud. Install helicoil. Perform ground run. Establish/check reference RPM. Troubleshoot. Rotorcraft flight controls Install swash plate. Install mixing box. Adjust pitch links. Rig collective system. Rig cyclic system. Rig anti-torque system. Check controls for assembly and locking. Check controls for operation and sense. Troubleshoot faulty system. Turbine Engines Replace module. Replace fan blade. Hot section inspection/borescope check. Carry out engine/compressor wash. Carry out engine dry cycle. Engine ground run. Establish reference power. Trend monitoring/gas path analysis. Troubleshoot. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 72

Fuel and control, piston Replace engine driven pump. Adjust AMC. Adjust ABC. Install carburettor/injector. Adjust carburettor/injector. Clean injector nozzles. Replace primer line. Check carburettor float setting. Troubleshoot faulty system. Ignition systems, turbine Perform functional test of the ignition system. Check glow plugs/ignitors. Check H.T. leads. Check ignition unit. Replace ignition unit. Troubleshoot faulty system. Fuel and control, turbine Replace FCU. Replace Engine Electronic Control Unit (FADEC). Replace Fuel Metering Unit (FADEC). Replace engine driven pump. Clean/test fuel nozzles. Clean/replace filters. Adjust FCU. Troubleshoot faulty system. Functional test of FADEC. Engine Controls Rig thrust lever. Rig RPM control. Rig mixture HP cock lever. Rig power lever. Check control sync (multi-eng). Check controls for correct assembly and locking. Check controls for range and direction of movement. Adjust pedestal micro-switches. Troubleshoot faulty system. Ignition systems, piston Change magneto. Change ignition vibrator. Change plugs. Test plugs. Check H.T. leads. Install new leads. Check timing. Check system bonding. Troubleshoot faulty system. Engine Indicating Replace engine instruments(s). Replace oil temperature bulb. Replace thermocouples. Check calibration. Troubleshoot faulty system. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 73

Exhaust, piston Replace exhaust gasket. Inspect welded repair. Pressure check cabin heater muff. Troubleshoot faulty system. Starting Replace starter. Replace start relay. Replace start control valve. Check cranking speed. Troubleshoot faulty system. Exhaust, turbine Change jet pipe. Change shroud assembly. Install trimmers. Inspect/replace thrust reverser. Replace thrust reverser component. Deactivate/reactivate thrust reverser. Operational test of the thrust reverser system. Turbines, piston engines Replace PRT. Replace turbo-blower. Replace heat shields. Replace waste gate. Adjust density controller. Oil Change oil. Check filter(s). Adjust pressure relief valve. Replace oil tank. Replace oil pump. Replace oil cooler. Replace firewall shut off valve. Perform oil dilution test. Engine water injection Replace water/methanol pump. Flow check water/methanol system. Adjust water/methanol control unit. Check fluid for quality. Troubleshoot faulty system Troubleshoot faulty system. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 74

Accessory gear boxes Replace gearbox. Replace drive shaft. Inspect magnetic chip detector. APU Removal/installation of the APU. Removal/installation of the inlet guide-vane actuator. Operational test of the APU emergency shut-down test. Operational test of the APU. ETC Technician Apprenticeship Scheme - Aircraft Maintenance Technician Practical Training/Basic Experience Log Book Page 75