Codici errore Universal Send Kit #001 -Check your document. -Paper jam. #003 -Document is too long. -Communications that take longer than a preset time (64 minutes) an error. #005 -No answer. -The other party did not answer within 35 seconds. -The receiving machine is not a G3 fax. #009 -Load paper. -Either there is no recording paper, or the paper feed cassette is not correctly set. #011 -Check your document. -The document you are sending was not placed correctly. #012 -No paper in the remote unit. -The document could not be sent be the receiving fax machine was out of paper. #018 -Busy/No signal. -The other party did not respond when your machine dialed/redialed. -The documents could not be sent be the other party was engaged with another communication with another party. #022 -Fowarding cannot be performed be the contents of the Group Address specified as forwarding destinations have been deleted or are only User Inboxes. Transmission cannot be performed be, when you send documents to destinations registered in an Address Book, the destinations are deleted from the Address Book -Remove any jammed paper. -Change the resolution to any setting other than ultra-fine, and send the document again. -When receiving a document, ask the remote party to either reduce the resolution at which the document is scanned, or divide the document into two or more parts before sending it. -Confirm that the remote machine is able to communicate, and try again -Confirm this with the receiving party. -Either replenish the recording paper, or correctly set the paper drawer. -Place it again, and resend. -Ask the other party to load the paper drawer. -Confirm that the remote party is able to communicate, and try again. -Set the forwarding destinations/addresses in the Address Book correctly.
while awaiting transmission. #037 -The memory is full (Memory for I-Fax reception is full). -Reception is rejected be the printer is not ready to print. #080 -Subaddress TX rejected. -A subaddress is not set in the remote machine. #081 -Password TX rejected. -A password is not set in the remote machine. #099 -Copy/print is interrupted. -Stop button was pressed during communication #102 -Check Subaddress/Password. -The subaddress and/or RX passwords do not match. #107 -The memory is full. -A document could not be sent be there was no memory available. #701 -No Department ID was set when the job was entered, or the password has changed. #702 -Unable to operate be memory is full. -Wait until automatically recovered. -Print out documents stored in the memory with MEMORY RX or RECEIVED IN MAIL BOX -Erase error documents or unwanted documents in order to make memory available. -If an error occurs in the printer, eliminate the. -Check the subaddress of the remote party, and try again. Check the password of the remote party, and try again. -Try to copy/print again. -Try communication again -Check the subaddress and/or RX passwords and try again. -Either send the document after the end of memory copying, resend the document at a lower resolution, or erase unwanted documents in order to make memory available. -Enter the correct Department ID or password -Please wait a few moments. -Try again, after other Send jobs are complete. -Do not send a document to multiple recipients at the same time. -Send the document in smaller partitions and/or to a smaller number of recipients. #703 -Unable to write be the image area of memory is full. -Please wait a few moments. -Try again after other Send jobs complete. -Erase documents stored in a box. If the machine still does not operate normally, turn the main power OFF, then turn
it back ON. #704 -An error occurred when receiving address information from the Address Book while sending an e-mail. #705 -The Send operation was interrupted be the size of the image data on one page is larger than the Send Data Size Limit set from the Additional Functions screen. #706 -The Address Book is being imported or exported from the Remote UI, or it is being used by another sending component. #711 -The box memory is full. #712 -The maximum number of documents is stored in a box. #749 -Be the service call message is being displayed, you cannot perform jobs. #751 -FTP server is not set up. -The network with the FTP server is cut off. (Cannot connect to the destination, or the line is severed in the middle) #752 -The SMTP server name is not correct, or the server is not functioning. -The domain name or e-mail address may not be set. -The Network is down. #753 -An error occurs in TCP/IP when transmitting to the FTP server, transmitting e-mail, and/or I-Fax transmission/reception. (Error of Socket, Select, etc.) -Check the address settings. If the machine still does not operate normally, turn the main power OFF, then turn it back ON. -Change the setting for the Send Data Size Limit from the Additional Functions screen. (See Specifying the Settings for Sending e-mail, ) in your reference instruction manual of the machine that you are working on. -Try sending again. -Erase documents stored in the box. -Delete the documents stored in the box. -Turn the main power off, wait for 10 seconds, and turn the main power back on. If the machine still does not work, turn the main power off, and unplug the machine, and contact a service representative. After the service call message disappears, send the job again. -Check the destination. -Check the network. -Check the FTP server settings. -Check the SMTP server name, domain name, and e-mail address set in the Additional Functions screen. -Check that the SMTP server is operating properly. -Check the network status. -Check the network cables and connectors. If the machine still does not operate normally, turn the main power OFF, then turn it back ON.
#754 -The Server is not functioning when sending data to the database or the network is down. -The Database s address setting is not correct. #755 -You cannot send jobs be TCP/IP is not functioning correctly. -IP address is not set. -When configuring the machine, the IP address is not correctly registered for either DHCP, RARP or BOOTP. #756 -The NetWare setting from the Additional Functions screen is set to OFF. -Check the server and network. -Check the database s address settings. -Check the TCP/IP setting on the Additional Functions screen. -Set the NetWare setting to ON. #801 -A timeout error occurred during communication with the SMTP server to transmit an e-mail, or to transmit/receive I-Fax, due to a problem with the server. -The SMTP server returned an error while trying to connect. -The e-mail address is not correct. #802 -The SMTP server or DNS server name is not correct from the settings in Additional Functions screen. -Connection to the DNS server failed. #803 -Before sending all pages, the network connection was cut by the recipient. #804 -Unable to match a specified directory name when sending data to a database or file server. -The specified directory was not found when transmitting to the FTP server. -The Folder ID is not correct. -Incorrect upload directory. -No authority to access the folder. -Not allowed access to the upload directory. #805 -Insufficient hard disk space on the database server. -Check that the SMTP server is operating properly. -Check the network status. -Check the e-mail address setting -Check the name of the SMTP server set in the Additional Functions screen. -Check that the DNS server is operating properly. -Send the documents again. -Change the Folder ID of the recipient s address. -Change the upload directory for the destination. -Change the setting to enable access to the folder from the server side. -Configure the server to allow access. -Delete documents stored on the server.
#806 -Incorrect user name or password was specified when sending to the file server/ftp server. #807 -You do not have the authority to access the specified directory. -Change the user name or password of the recipient/destination. -Set the authority required to access the server s directory, then send again to the accessible server. #808 -An error occurred on the server while sending data to a file server/ftp server. #809 -A same file name exists on the server and cannot be overwritten. -Reboot the server or perform other maintenance techniques as necessary. -Change the settings on the file server to enable overwriting. #810 -A connection error for the POP3 server occurs when receiving I-Fax. -The POP3 server returned an error message during the POP3 connection. -A timeout error occurs during connection with the POP3 server due to the server s problem. #812 -A password error occurs when the POP3 server s user authentication to receive IFax. #813 -A user account error occurs when the POP3 server s user Authentication to receive I-Fax. -Check the POP3 server name settings in Additional Functions. -Check that the POP3 server works properly. -Check the password setting for the POP3 account in Additional Functions. -Check the POP3 account settings in Additional Functions. #815 -Attempted to log on to a file server that has already been logged on by you. You cannot log on to the same device with the same user name. #816 -Unavailable to print be the quantity exceeded the limit set in Department ID Management. -Wait a few moments to send the data again; change the NetWare server to send, or stop the Pserver. -Contact your system manager. #817 -A communication error with the remote copy printers occurred. -Check the network, and try again. If the machine still does not
operate correctly, contact your system manager #819 -Due to corruption of data of the e-mail or I-Fax, failure to separate the message text from the image data. #820 -The attached image format is not of Base64/uuencode format, or corruption of the data failed to print the received image. #821 -The received image format is not compatible to the machine. #822 -You have received data that cannot be processed. (Image cannot be decoded.) #823 -Unable to connect with the remote copy printers. -Ask the sender to resend the data. -Ask the sender to change the image format and resend it. -Ask the sender to change the image format and resend it. -Check the settings and ask the sender to resend. -Check the network, and try again. If the machine still does not operate correctly, contact your system manager. #824 -A communication error with the remote copy printers occurred. -Check the network, and try again. If the machine still does not operate correctly, contact your system manager. #825 -The Department ID and password of the copy job are not registered in the remote copy printers. Printing cannot be performed be the ID and password of the reserved or current print jobs have been deleted or the password has been changed. #827 -You have received data that cannot be processed. (Contains MIME information that is not supported.) #828 -You have received HTML data. #829 -The received image exceeds the maximum size the machine can receive. -Register the Department ID and password of the copy job in the remote copy printers. Use the remote copy printer in which the Department ID and password of the copy job are registered. Try again with a different Department ID and password. If you do not know the password, contact your system manager. -Check the settings and ask the sender to resend. -Ask the sender to use a file format other than HTML and resend. -If the server is set up to keep error messages, allocate more space for incoming mail or retrieve the file with another computer -If the server is not set up to keep error messages or is
set to the SMTP receiving mode, allocate more space for incoming mail and ask the sender to re-send the image. Alternatively, you could ask the sender to reduce the file size by lowering the image resolution or dividing it into smaller files. #830 -DSN error notification is received be of incorrect I- Fax address and destination condition settings, or the data size of the sent documents exceed the mail server capacity. #831 -I-Fax document is not received using SMTP be of the RX/Print Range setting in the IP Address Range Settings in Additional Functions. #832 -The DSN mail was not sent be the e-mail settings and network settings in Additional Functions have not been set or trouble has occurred at the mail server end. #833 -The MDN mail has not been sent be the network Settings in Additional Functions have not been set or trouble has occurred at the mail server end. #834 -An MDN error notification is received be I-Fax address or destination condition settings are incorrect, trouble has occurred in the network or mail server, or the memory of the machine at the recipient s end is full. #835 -The received text contains in excess of maximum number of lines that can be received at a time. #851 -Not enough memory in the main unit, or the scanned document cannot be stored be there are more than 100 documents I in the specified Mail Box. -Check the I-Fax address and destination condition settings. -Set the maximum data size for sending so that it is less than the email server capacity. -Check the status of the mail server, DNS server, and network. -Reset the RX/Print Range setting in the IP Address Range Settings in Additional Functions. -Check the DNS server Settings in the Network Settings, and the E-mail/I-fax, and IP address settings in Additional Functions. -Check the status of the mail server and DNS server. -Check the DNS Server Settings in the Network Settings, and the E-mail/I-Fax, and IP address settings in Additional Functions. -Check the status of the mail server and DNS server. -Check the I-Fax address and destination condition settings. -Ask the sender to reduce the number of lines in the text and resend it. (Maximum receivable lines : approx. 300 lines = 3 pages in LTR size format) -Ask the sender not to send the text in uuencode format in the case that the sender is using Outlook Express as a mailing software. -Check the available memory of the main unit, and delete unwanted documents in the boxes. If there are a large number of documents, delete them from the specified Mail Box. #852
-An error occurred be the main power switch was turned OFF while a job was being processed. #853 -When trying to print a large number of pages, the job is not performed due to insufficient memory resources. -Using the wrong print driver. #899 -The e-mail or I-Fax has been successfully sent, but reception may be incomplete be transmission was relayed via multiple servers. #995 -Reserved jobs were cleared. -Check to see if the main power switch is ON. Try processing the job again if necessary. -Reduce the number of pages to print or perform the print job again when other jobs are not reserved. -Make sure that the print driver that you re using is the correct one for that specific model printer that you re printing to. -Confirm whether reception was complete. -Check if you receive an error mail. -Repeat the procedure as necessary.