Concrete Design to Eurocode 2



Similar documents
Introduction to Eurocode 2

RC Detailing to Eurocode 2

Introduction. Eurocodes. Specification. Cost

Eurocode 2: Design of concrete structures

Page 1 of Sven Alexander Last revised SB-Produksjon STATICAL CALCULATIONS FOR BCC 250

The design process. Design life. Actions on structures. How to design concrete structures using Eurocode 2 2. Getting started

Companion Document. EN : Eurocode 2: Design of Concrete Structures Part 1: General rules and rules for buildings

DESIGN OF SLABS. Department of Structures and Materials Engineering Faculty of Civil and Environmental Engineering University Tun Hussein Onn Malaysia

The following sketches show the plans of the two cases of one-way slabs. The spanning direction in each case is shown by the double headed arrow.

EN DK NA:2007

16. Beam-and-Slab Design

Design of reinforced concrete columns. Type of columns. Failure of reinforced concrete columns. Short column. Long column

NATIONAL ANNEX TO STANDARD SFS-EN 1990 EUROCODE BASIS OF STRUCTURAL DESIGN

DESIGN OF SLABS. 3) Based on support or boundary condition: Simply supported, Cantilever slab,

Standards, Codes and Regulations

Chapter - 3 Design of Rectangular Beams and One-way Slabs

Standards, Codes and Regulations

HOW TO DESIGN CONCRETE STRUCTURES Foundations

STRUSOFT EXAMPLES PRE-STRESS 6.4

EUROCODE 1 Actions on Building Structures

Ministry of the Environment Decree on applying Eurocode standards in building construction

Basics of Reinforced Concrete Design

Copyright: European Concrete Platform ASBL, May 2008.

October ICS Supersedes ENV , ENV , ENV , ENV , ENV and ENV

Eurocode 3 for Dummies The Opportunities and Traps

A transverse strip of the deck is assumed to support the truck axle loads. Shear and fatigue of the reinforcement need not be investigated.

Eurocode 4: Design of composite steel and concrete structures

SECTION 3 DESIGN OF POST- TENSIONED COMPONENTS FOR FLEXURE

DS/EN 1990 DK NA:2013

Reinforced Concrete Design Project Five Story Office Building

Properties of Concrete for use in Eurocode 2

Technical Notes 3B - Brick Masonry Section Properties May 1993

Deflection Calculation of RC Beams: Finite Element Software Versus Design Code Methods

Chapter 5 Bridge Deck Slabs. Bridge Engineering 1

Code of Practice for Structural Use of Concrete 2013

Concrete Frame Design Manual

SECTION 3 DESIGN OF POST TENSIONED COMPONENTS FOR FLEXURE

Design MEMO 60 Reinforcement design for TSS 102

SEISMIC DESIGN. Various building codes consider the following categories for the analysis and design for earthquake loading:

The introduction of the Eurocodes for Concrete design will alter the way that shear is approached for

Design MEMO 54a Reinforcement design for RVK 41

Structural Analysis. EUROCODE 2 Background and Applications

Detailing of Reinforcment in Concrete Structures

Design of Steel Structures Prof. S.R.Satish Kumar and Prof. A.R.Santha Kumar

Seismic design of beam-column joints in RC moment resisting frames Review of codes

EVALUATION OF SEISMIC RESPONSE - FACULTY OF LAND RECLAMATION AND ENVIRONMENTAL ENGINEERING -BUCHAREST

Eurocode 5: Design of timber structures

5 Steel elements. 5.1 Structural design At present there are two British Standards devoted to the design of strucof tural steel elements:

STEEL BUILDINGS IN EUROPE. Multi-Storey Steel Buildings Part 10: Guidance to developers of software for the design of composite beams

Manual for the design of reinforced concrete building structures to EC2

1.054/1.541 Mechanics and Design of Concrete Structures (3-0-9) Outline 1 Introduction / Design Criteria for Reinforced Concrete Structures

Design rules for bridges in Eurocode 3

HUS-V Screw anchor. HUS-V Screw anchor. Basic loading data (for a single anchor) Mean ultimate resistance

Optimum proportions for the design of suspension bridge

Hilti HIT-HY 150 MAX with rebar

EUROPEAN ORGANISATION FOR TECHNICAL APPROVALS

PERFORMANCE OF SLABS REINFORCED BY PEIKKO PSB STUDS

ick Foundation Analysis and Design

Structural fire design Eurocode Timber structures

ETABS. Integrated Building Design Software. Concrete Frame Design Manual. Computers and Structures, Inc. Berkeley, California, USA

EN Eurocode 1 Accidental Actions. Ton Vrouwenvelder TNO Bouw / TU Delft. EUROCODES Background and Applications

INTRODUCTION TO BEAMS

Stresses in Beam (Basic Topics)

National Council of Examiners for Engineering and Surveying. Principles and Practice of Engineering Structural Examination

How To Make A Steel Beam

Detailing of Reinforcement in Concrete Structures

SEISMIC UPGRADE OF OAK STREET BRIDGE WITH GFRP

MECHANICS OF SOLIDS - BEAMS TUTORIAL 1 STRESSES IN BEAMS DUE TO BENDING. On completion of this tutorial you should be able to do the following.

Hardened Concrete. Lecture No. 14

Department of Civil Engineering B.TECH 5 TH SEM Lecture Notes on STRUCTURAL DESIGN BCE301

HSL-3 Heavy duty anchor carbon steel. Anchor Fastening Technology Manual HSL-3. Heavy duty anchor. Version /

INTRODUCTION TO LIMIT STATES

Design Manual to BS8110

1.2 Advantages and Types of Prestressing

USE OF CFRP LAMINATES FOR STRENGTHENING OF REINFORCED CONCRETE CORBELS

MATERIALS AND MECHANICS OF BENDING

Chapter 2 Basis of design and materials

IMPROVING THE STRUT AND TIE METHOD BY INCLUDING THE CONCRETE SOFTENING EFFECT

FOOTING DESIGN EXAMPLE

Nonlinear Analysis of Reinforced Concrete Structures in Design and Structural Assessment

SEISMIC RETROFITTING TECHNIQUE USING CARBON FIBERS FOR REINFORCED CONCRETE BUILDINGS

SECTION 5 ANALYSIS OF CONTINUOUS SPANS DEVELOPED BY THE PTI EDC-130 EDUCATION COMMITTEE LEAD AUTHOR: BRYAN ALLRED

APOLLO SALES LTD SITE SCAFFOLD STEP DESIGN CHECK CALCULATIONS

Seismic Risk Prioritization of RC Public Buildings

HUS-HR, CR Screw anchor, stainless steel

Optimising plate girder design

Reinforced Concrete Design

Seismic Assessment and Retrofitting of Structures: Eurocode8 Part3 and the Greek Code on Seismic Structural Interventions

Numerical modelling of shear connection between concrete slab and sheeting deck

BFS 2013:10 EKS 9. Section A General provisions. Scope of validity. Consolidated Version as last amended by BFS 2013:10 EKS 9

DS/EN DK NA:2014

FOUNDATION DESIGN. Instructional Materials Complementing FEMA 451, Design Examples

Miss S. S. Nibhorkar 1 1 M. E (Structure) Scholar,

SLAB DESIGN. Introduction ACI318 Code provides two design procedures for slab systems:

Draft Table of Contents. Building Code Requirements for Structural Concrete and Commentary ACI

HVU with HAS/HAS-E rod adhesive anchor

Eurocode 1: Actions on structures Part 1-1: General actions - Densities, self-weight, imposed loads for buildings

Fire safety in timber buildings

Strengthening of Large Storage Tank Foundation Walls in an Aggressive Environment by External Post-tensioning. May 7th 2013: Dominique Deschamps

Structural use of concrete

Transcription:

Concrete Design to Eurocode 2 Jenny Burridge MA CEng MICE MIStructE Head of Structural Engineering

Introduction to the Eurocodes Eurocode Eurocode 1 Eurocode 2 Materials Cover Flexure Shear Deflection Further Information

The Eurocodes BS EN 1990 (EC0) : Basis of structural design BS EN 1991 (EC1) : Actions on Structures BS EN 1992 (EC2) : Design of concrete structures BS EN 1993 (EC3) : Design of steel structures BS EN 1994 (EC4) : Design of composite steel and concrete structures BS EN 1995 (EC5) : Design of timber structures BS EN 1996 (EC6) : Design of masonry structures BS EN 1997 (EC7) : Geotechnical design BS EN 1998 (EC8) : Design of structures for earthquake resistance BS EN 1999 (EC9) : Design of aluminium structures

The Eurocodes BS EN 1990 (EC0): Basis of structural design BS EN 1991 (EC1): Actions on Structures BS EN 1992 (EC2): Design of concrete structures BS EN 1993 (EC3): Design of steel structures BS EN 1994 (EC4): Design of composite steel and concrete structures BS EN 1995 (EC5): Design of timber structures BS EN 1996 (EC6): Design of masonry structures BS EN 1997 (EC7): Geotechnical design BS EN 1998 (EC8): Design of structures for earthquake resistance BS EN 1999 (EC9): Design of aluminium structures

Features of the Eurocodes The Eurocodes contain Principles (P) which comprise: General statements and definitions for which there is no alternative, as well as: Requirements and analytical models for which no alternative is permitted They also contain Application Rules, which are generally rules which comply with the Principles The Eurocodes also use a comma (,) as the decimal marker Each Eurocode part has a National Annex which modifies the main text of the Eurocode

National Annex The National Annex provides: Values of Nationally Determined Parameters (NDPs) (NDPs have been allowed for reasons of safety, economy and durability) Example: Min diameter for longitudinal steel in columns φ min = 8 mm in text φ min = 12 mm in N.A. The decision where main text allows alternatives Example: Load arrangements in Cl. 5.1.3 (1) P The choice to adopt informative annexes Example: Annexes E and J are not used in the UK Non-contradictory complementary information (NCCI) TR 43: Post-tensioned concrete floors design handbook

Introduction to the Eurocodes Eurocode Eurocode 1 Eurocode 2 Materials Cover Flexure Shear Deflection Further Information

Eurocode Published 27 July 2002 Structures are to be designed, executed and maintained so that, with appropriate forms of reliability, they will: Perform adequately under all expected actions Withstand all actions and other influences likely to occur during construction and use Have adequate durability in relation to the cost Not be damaged disproportionately by exceptional hazards

Eurocode The code sets out the following: Basis for calculating design resistance of materials Combinations of actions for ultimate limit state Persistent Transient Accidental Seismic Combinations of actions for serviceability limit state

Eurocode Design values of actions, ultimate limit state persistent and transient design situations (Table A1.2(B) Eurocode) Comb tion expression reference Permanent actions Leading variable action Accompanying variable actions Unfavourable Favourable Main(if any) Others Eqn (6.10) γ1.35 G,j,sup GG k k,j,sup 1.0 γ G,j,inf G k G k,j,inf 1.5 γ Q,1 Q k,1 1.5 γ Q,i Ψ 0,i Q k,i Eqn (6.10a) γ1.35 G,j,sup GG k k,j,sup 1.0 γ G,j,inf G k G k,j,inf 1.5 γ Q,1 Ψ 0,1 Q k,1 k 1.5 γ Q,i Ψ 0,i Q k,i Eqn (6.10b) ξ0.925x1.35g γ G,j,sup G k,j,supk 1.0 γ G,j,inf G k G k,j,inf 1.5 γ Q,1 Q k,1 1.5 γ Q,i Ψ 0,i Q k,i For one variable action: 1.25 G k + 1.5 Q k Provided: 1. Permanent actions < 4.5 x variable actions 2. Excludes storage loads

Introduction to the Eurocodes Eurocode Eurocode 1 Eurocode 2 Materials Cover Flexure Shear Deflection Axial Further Information

Eurocode 1 Eurocode 1 has ten parts: 1991-1-1 Densities, self-weight and imposed loads 1991-1-2 Actions on structures exposed to fire 1991-1-3 Snow loads 1991-1-4 Wind actions 1991-1-5 Thermal actions 1991-1-6 Actions during execution 1991-1-7 Accidental actions due to impact and explosions 1991-2 Traffic loads on bridges 1991-3 Actions induced by cranes and machinery 1991-4 Actions in silos and tanks

Eurocode 1 Eurocode 1 Part 1-1: Densities, self-weight and imposed loads Bulk density of reinforced concrete is 25 kn/m 3 The UK NA uses the same loads as BS 6399 Plant loading not given

Introduction to the Eurocodes Eurocode Eurocode 1 Eurocode 2 Materials Cover Flexure Shear Deflection Further Information

Eurocode 2 Relationships BS EN 1997 GEOTECHNICAL DESIGN BS 8500 Specifying Concrete BS EN 13670 Execution of Structures BS EN 1990 BASIS OF STRUCTURAL DESIGN BS EN 1991 ACTIONS ON STRUCTURES BS EN 1992 DESIGN OF CONCRETE STRUCTURES Part 1-1: General Rules for Structures Part 1-2: Structural Fire Design BS EN 1998 SEISMIC DESIGN BS 4449 Reinforcing Steels BS EN 10080 Reinforcing Steels BS EN 1994 Design of Comp. Struct. BS EN 1992 Part 2: Bridges BS EN 1992 Part 3: Liquid Ret. Structures BS EN 13369 Pre-cast Concrete

Eurocode 2/BS 8110 Compared Code deals with phenomena, rather than element types Design is based on characteristic cylinder strength Does not contain derived formulae (e.g. only the details of the stress block is given, not the flexural design formulae) Unit of stress in MPa One thousandth is represented by %o Plain or mild steel not covered Notional horizontal loads considered in addition to lateral loads High strength, up to C90/105 covered

Materials

Concrete properties (Table 3.1) Strength classes for concrete f ck (MPa) 12 16 20 25 30 35 40 45 50 55 60 70 80 90 f ck,cube (MPa) 15 20 25 30 37 45 50 55 60 67 75 85 95 105 f cm (MPa) 20 24 28 33 38 43 48 53 58 63 68 78 88 98 f ctm (MPa) 1.6 1.9 2.2 2.6 2.9 3.2 3.5 3.8 4.1 4.2 4.4 4.6 4.8 5.0 E cm (GPa) 27 29 30 31 33 34 35 36 37 38 39 41 42 44 BS 8500 includes C28/35 & C32/40 For shear design, max shear strength as for C50/60 f ck f ck,cube f cm f ctm E cm = Concrete cylinder strength = Concrete cube strength = Mean concrete strength = Mean concrete tensile strength = Mean value of elastic modulus

Reinforcement properties (Annex C) Product form Bars and de-coiled rods Wire Fabrics Class A B C A B C Characteristic yield strength f yk or f 0,2k (MPa) 400 to 600 k = (f t /f y ) k 1,05 1,08 1,15 <1,35 1,05 1,08 1,15 <1,35 Characteristic strain at maximum force, ε uk (%) 2,5 5,0 7,5 2,5 5,0 7,5 Fatigue stress range (N = 2 x 10 6 ) (MPa) with an upper limit of 0.6f yk 150 100 In UK NA max. char yield strength, f yk, = 600 MPa BS 4449 and 4483 have adopted 500 MPa

Extract BS 8666

Cover

BS EN 1992-1-1 & Cover Nominal cover, c nom Minimum cover, c min c min = max {c min,b ; c min,dur ; 10 mm} Allowance for deviation, c dev Axis distance, a Fire protection

BS EN 1992-1-1 & Cover Minimum cover, c min c min = max {c min,b ; c min,dur ;10 mm} c min,b = min cover due to bond (φ)

BS EN 1992-1-2 Structural fire design Scope Part 1-2 Structural fire design gives several methods for fire engineering Tabulated data for various elements is given in section 5 Reinforcement cover Axis distance, a, to centre of bar a Axis Distance a = c + φ m /2 + φ l

µ fi = N Ed,fi / N Rd or conservatively 0.7 Columns: Method A

Flexure

Simplified Stress Block For grades of concrete up to C50/60, ε cu = 0.0035 η = 1 λ = 0.8 f cd = α cc f ck / γ c = 0.85 f ck /1.5 = 0.57 f ck f yd = f yk /1.15 = 435 MPa

Design flowchart The following flowchart outlines a design procedure for rectangular beams with concrete classes up to C50/60 and class 500 reinforcement Carry out analysis to determine design moments (M) Determine K and K from: M K = & K' = 0.6δ 0.18δ 2 0. 21 b d 2 f ck Note: δ = 0.8 means 20% moment redistribution. Yes Beam is under-reinforced - no compression steel needed Is K K? No Beam is over-reinforced - compression steel needed δ K 1.00 0.208 0.95 0.195 0.90 0.182 0.85 0.168 0.80 0.153 0.75 0.137 0.70 0.120 It is often recommended in the UK that K is limited to 0.168 to ensure ductile failure

Flow chart for under-reinforced beam Calculate lever arm Z from: z = [ 1+ 1 3.53K ] 0. 95d d 2 Calculate tension steel required from: A s = M f z yd Check minimum reinforcement requirements: 0.26f b d ctm t A 0. 013 b s,min f yk t d Check max reinforcement provided A s,max 0.04A c (Cl. 9.2.1.1) Check min spacing between bars > φ bar > 20 > A gg + 5 Check max spacing between bars

Flow chart for over-reinforced beam Calculate lever arm Z from: d z = [ 1+ 1 3.53K' ] Calculate excess moment from: 2 M = bd f ( K ') ck Calculate compression steel required from: M A 2 s2 = f d d yd ( ) 2 2 K 2 Calculate tension steel required from: M M ' A = + s f z yd A s2 f f sc yd Check max reinforcement provided A s,max 0.04A c (Cl. 9.2.1.1) Check min spacing between bars > φ bar > 20 > A gg + 5

Shear

Eurocode 2/BS 8110 Compared

Strut inclination method V Rd,max = α cw b w z cotθ + ν 1 f tanθ cd V = Rd, s A sw s z fywd cotθ 21.8 < θ < 45

Shear We can manipulate the Expression for the concrete strut: When cot θ = 2.5 (θ = 21.8 ) V Rd,max = 0.138 b w z f ck (1 - f ck /250) Or in terms of stress: v Rd = 0.138 f ck (1 - f ck /250) where v Rd = V Rd /(b z) = V Rd /(0.9 bd) When v Rd > v Ed cot θ = 2.5 (θ = 21.8 ) When v Rd < v Ed we can rearrange the concrete strut expression: θ = 0,5 sin -1 [v Rd /(0.20 f ck (1 - f ck /250))] We can also manipulate the reinforcement expression to give: A sw /s = v Ed b w /(f ywd cot θ) f ck v Rd (when cot θ = 2.5) 20 2.54 25 3.10 28 3.43 30 3.64 32 3.84 35 4.15 40 4.63 45 5.08 50 5.51

Design flow chart for shear Determine v Ed where: v Ed = design shear stress [v Ed = V Ed /(b w z) = V Ed /(b w 0.9d)] Determine the concrete strut capacity v Rd when cot θ = 2.5 v Rd = 0.138f ck (1-f ck /250) Is v RD > v Ed? No Determine θ from: θ = 0.5 sin -1 [(v Ed /(0.20f ck (1-f ck /250))] Yes (cot θ = 2.5) Calculate area of shear reinforcement: A sw /s = v Ed b w /(f ywd cot θ) Check maximum spacing of shear reinforcement : s,max = 0.75 d For vertical shear reinforcement

Deflection

Deflection The deflection limits are: Span/250 under quasi-permanent loads to avoid impairment of appearance and general utility Span/500 after construction under the quasi-permanent loads to avoid damage to adjacent parts of the structure. Deflection requirements can be satisfied by the following methods: Direct calculation (Eurocode 2 methods considered to be an improvement on BS 8110). Limiting span-to-effective-depth ratios

EC2 Span/effective depth ratios l 3 2 ρ0 ρ0 = K 11+ 1,5 f + ck 3,2 fck 1 if ρ ρ (7.16.a) 0 d ρ ρ l d = K 11 + 1,5 f ck ρ0 + ρ ρ' 1 12 f ck l/d is the span/depth ratio K is the factor to take into account the different structural systems ρ 0 is the reference reinforcement ratio = f ck 10-3 ρ is the required tension reinforcement ratio at mid-span to resist the moment due to the design loads (at support for cantilevers) ρ is the required compression reinforcement ratio at midspan to resist the moment due to design loads (at support for cantilevers) ρ' ρ 0 if ρ > ρ 0 (7.16.b)

EC2 Span/effective depth ratios Structural system K Simply supported beam, one- or two-way simply supported slab End span of continuous beam or one-way spanning slab continuous slab or two-way slab over continuous over one long side Interior span of beam or one-way or two-way spanning slab Slab supported without beams (flat slab) (based on longer span) 1.0 1.3 1.5 1.2 Cantilever 0.4

EC2 Span/effective depth ratios Span to depth ratio (l/d) 18.5 Percentage of tension reinforcement (A s,req d /bd)

Flow Chart Determine basic l/d Factor F1 for ribbed and waffle slabs only F 1 = 1 0.1 ((b f /b w ) 1) 0.8 Factor F2 for spans supporting brittle partitions > 7m F 2 = 7/l eff Factor F3 accounts for stress in the reinforcement F3 = 310/σ s where σ s is tensile stress under quasi-permanent load Note: A s,prov 1.5 No A s,req d (UK NA) Increase A s,prov or f ck Is basic l/d x F1 x F2 x F3 >Actual l/d? No Yes Check complete

Axial

Column design process Determine the actions on the column Determine the effective length, l 0 Determine the first order moments Determine slenderness, λ Determine slenderness limit, λ lim No Is λ λ lim? Yes Column is slender Column is not slender, M Ed = M 02 Calculate A s (eg using column chart) Check detailing requirements

Effective length Actions Effective length, l 0 θ First order moments θ M Slenderness, λ l 0 = l l 0 = 2l l 0 = 0,7l l 0 = l / 2 l 0 = l l /2 <l 0 < l Braced members: l 0 = 0,5l k1 1+ 0,45 + k Unbraced members: 1 k2 1+ 0,45 + k 2 l 0 > 2l Slenderness limit, λ lim Is λ λ lim? Yes Slender No Not slender, M Ed = M 02 l 0 = l max 1+ 10 k k + k k1 1+ 1+ k k 1+ 1+ k k1 2 2 1 2 ; 1 2 Calculate A s Detailing

Effective length (2) From Eurocode 2: k = (θ / M) (EΙ / l) Alternatively... k = Where: E Ic lc 2E I l b b 0.1 (From PD 6687: Background paper to UK NA) I b,i c are the beam and column uncracked second moments of area l b,l c are the beam and column lengths Actions Effective length, l 0 First order moments Slenderness, λ Slenderness limit, λ lim Is λ λ lim? Yes Slender No Not slender, M Ed = M 02 Calculate A s Detailing

Effective length (3) How to Columns has a look up table l o = Fl Actions Effective length, l 0 First order moments Slenderness, λ Slenderness limit, λ lim Is λ λ lim? Yes No Slender Not slender, M Ed = M 02 Calculate A s Detailing

Design moment The design moment M Ed is as follows: M 01 = Min { M top, M bottom } + e i N ed Actions Effective length, l 0 First order moments M 02 = Max { M top, M bottom } + e i N ed e i = Max {I o /400, h/30, 20} M 2 = N ed e 2 For stocky columns: M Ed = M 02 There are alternative, methods for calculating eccentricity, e 2, for slender columns Slenderness, λ Slenderness limit, λ lim Is λ λ lim? Yes Slender No Not slender, M Ed = M 02 Calculate A s Detailing

Slenderness Actions Second order effects may be ignored if they are less than 10% of the corresponding first order effects Second order effects may be ignored if the slenderness, λ < λ lim Slenderness λ = l 0 /i where i = (I/A) Effective length, l 0 First order moments Slenderness, λ Slenderness limit, λ lim hence for a rectangular section for a circular section λ = 3.46 l 0 / h λ = 4 l 0 / h Is λ λ lim? Yes No Slender With biaxial bending the slenderness should be checked separately for each direction and only need be considered in the directions where λ lim is exceeded Not slender, M Ed = M 02 Calculate A s Detailing

Slenderness Limit λ lim = 20 A B C/ n where: A = 1 / (1+0,2ϕ ef ) ϕ ef is the effective creep ratio; (if ϕ ef is not known, A = 0,7 may be used) B = (1 + 2ω) ω = A s f yd / (A c f cd ) (if ω is not known, B = 1,1 may be used) C = 1.7 - r m r m = M 01 /M 02 M 01, M 02 are first order end moments, M 02 M 01 (if r m is not known, C = 0.7 may be used) n = N Ed / (A c f cd ) Actions Effective length, l 0 First order moments Slenderness, λ Slenderness limit, λ lim Is λ λ lim? Yes Slender No Not slender, M Ed = M 02 Calculate A s Detailing

Slenderness limit factor C 105 knm 105 knm 105 knm Actions Effective length, l 0 First order moments Slenderness, λ -105 knm 105 knm Slenderness limit, λ lim r m = M 01 / M 02 = 0 / 105 = 0 C = 1.7 0 = 1.7 r m = M 01 / M 02 = 105 / -105 = -1 C = 1.7 + 1 = 2.7 r m = M 01 / M 02 = 105 / 105 = 1 C = 1.7 1 = 0.7 Is λ λ lim? Yes Slender No Not slender, M Ed = M 02 Calculate A s Detailing

Column design (2)

Introduction to the Eurocodes Eurocode Eurocode 1 Eurocode 2 Materials Cover Flexure Shear Deflection Further Information

Design aids from the UK concrete sector Concise Eurocode 2 How to compendium RC Spreadsheets www.eurocode2.info Worked Examples ECFE scheme sizing Properties of concrete

TCC Courses Eurocode 2 half-day course for building designers Background to Eurocode 2 for building designers (one day) Eurocode 2 with design workshops for building designers (one day) Background to Eurocode 2, including liquid retaining structures (one day) Design of Concrete Bridges to Eurocodes (one day) Two-day course for building designers

Other Resources Updated Detailing Manual Updated Green book Text Books Designer s Guides

Design Guidance Recent Concrete Industry Design Guidance is written for Eurocode 2 TR 64 Flat Slab TR43 Posttensioned Slabs TR58 Deflections

Introduction to the Eurocodes Eurocode Eurocode 1 Eurocode 2 Materials Flexure Shear Deflection Axial Further Information Worked Example

Worked Example G k = 75 kn/m, Q k = 50 kn/m 10 m Cover = 40mm to each face f ck = 30 1000 Check the beam for flexure, shear and deflection 600

Solution - Flexure Carry out analysis to determine design moments (M) Determine K and K from: M K = bd 2 fck & K' = 0.6δ 0.18δ 2 0.21 Is K K? Yes Beam is under-reinforced - no compression steel needed ULS = (75 x 1.25 + 50 x 1.5) = 168.75 kn/m M ult = 168.75 x 10 2 /8 = 2109 knm d = 1000-40 - 10-16 = 934 6 2109 10 K = = 2 600 934 30 0.134 δ K 1.00 0.205 0.95 0.193 0.90 0.180 0.85 0.166 0.80 0.151 0.75 0.135

Solution - Flexure Calculate lever arm Z d z = 1+ 1 3.53K 0. 95 2 [ ] d z = = 934 2 806 [ 1+ 1 3.53 x 0.134] 0.95d Calculate tension steel M A = s f z yd A s 6 2109 x 10 = = 6015 mm 435 x 806 Provide 8 H32 (6430 mm 2 ) 2 Check max reinforcement provided Check min reinforcement provided Check min spacing between bars Check max spacing between bars Space between bars = 35mm > φ OK

Design flow chart for shear Determine v Ed where: v Ed = V Ed /(b w d) Determine the concrete strut capacity v Rd Shear force: V Ed = 168.75 x (10/2-0.934) = 686.1 kn Shear stress:v Ed = V Ed /(b w d) = 686.1 x 10 3 /(1000 x 600) = 1.14 MPa

Solution - Shear f ck v Rd (when cot θ = 2.5) 20 2.28 25 2.79 28 3.08 30 3.27 32 3.46 35 3.73 40 4.17 45 4.58 50 4.96

Design flow chart for shear Determine v Ed where: v Ed = V Ed /(b w d) Determine the concrete strut capacity v Rd Is v RD > v Ed? Shear force: V Ed = 168.75 x (10/2-0.934) = 686.1 kn Shear stress:v Ed = V Ed /(b w d) = 686.1 x 103/(1000 x 600) = 1.14 MPa v Rd = 3.27 MPa v Rd > v Ed cot θ = 2.5 Yes (cot θ = 2.5) Area of shear reinforcement: A sw /s = v Ed b w /(0.9 f ywd cot θ) Check maximum spacing of shear reinforcement : s l,max = 0.75 d A sw /s = 1.14 x 600 /(0.9 x 435 x 2.5) A sw /s = 0.70 mm Try H10 links with 2 legs. A sw s = 157 mm2 < 157 /0.70 = 224 mm provide H10 links at 200 mm CRS

Solution - Deflection Determine basic l/d Reinforcement ratio: ρ = A s /bd = 6430 x 100/(600 x 934) = 1.15%

Basic span-to-depth ratios (for simply supported condition) Span to depth ratio (l/d) 36 34 32 30 28 26 24 22 20 18 fck = 20 fck = 25 fck = 28 fck = 30 fck = 32 fck = 35 fck = 40 fck = 45 fck = 50 16 14.9 14 12 0.30% 0.80% 1.30% 1.80% Percentage of tension reinforcement (As/bd)

EC2 Span/effective depth ratios

Solution - Deflection Determine basic l/d Is b f > 3b w No j 1 = 1.0 Beam > 7m & support brittle partitions? Reinforcement ratio: ρ = A s /bd = 6430 x 100/(600 x 934) = 1.15% Req d l/d = 14.9 x 1.0 = 14.9 Actual l/d = 10000/934 = 10.7 Basic l/d > Actual l/d No j 2 = 1.0 Is actual l/d < (l/d).j 1.j 2? Yes Check complete