Technical Training Centers

Technical Training Centers Tampa, Florida 5903-A Hampton Oaks Pkwy Tampa, FL 33610 Phone: (813) 635-5701 Fax: (813) 623-5442 Atlanta, Georgia 5125 Highway 85 Atlanta, GA 30349 Phone: (813) 635-5701 Fax: (813) 623-5442 ISX15 CM2250 2013 Training Programs ISX11.9 CM2250 Available for Authorized Cummins Distributors, Dealers and Preferred Customers Basic Electronics (Theory & Troubleshooting) Cummins Engine Overhaul/Repair Cummins Factory Certifications (distributors and dealers only) Cummins & Onan Warranty Certifications (distributors and dealers only) Cummins Marine Engine Certifications (distributors and dealers only) Cummins Power Generation Programs (Small & Large Product) Customized Training Programs 1

Table of Contents Letter to Participants/Attendees. 3 Training Center Information. 4 General Information 4/5 * Registration * Cancellations * Schedule Changes * Tuition Costs * Lodging * Transportation * Daily Schedule * Supplies * Dress Code * Recognition Cummins Program Index. 7 Cummins 2010 Training Calendar.... 8/9 Cummins Program Descriptions.. 10-16 Power Generation Industrial Program Index. 17/18 Power Generation Consumer Program Index.. 19 Power Generation 2010 Training Calendar.... 20 Power Generation Program Descriptions 21-29 Cummins Learning Center.. 30 Lodging Information. 31 Maps 32/33 Registration Application Form.. 34 2

To: Cummins Virtual College, Cummins Learning Center, and Technical Service Center Participants/Attendees The year 2013 brings yet another round of new challenges. In 2013 several new engine platforms will be introduced. Along with the 2013 EPA certified ISB6.7, ISL9, ISX12 and ISX15, in late 2013 Cummins will also be introducing a new compressed natural gas onroad 12 liter engine, the ISX12-G CM2180. Virtually all of our on-highway diesel engines now feature the High Pressure Common Rail fuel system. In order to address the critical issue of technical competence, Cummins Power South has reengineered its commitment to provide product training programs that will increase the knowledge level of those individuals empowered to service and support these varied products. Cummins Virtual College (a CD-ROM based training delivery system) and the new Cummins Learning Center (on-line instruction/qualification) are two of the most advanced, comprehensive, and cost effective learning steps you can take in making sure you are competent to meet the challenges associated with today s advanced products. In addition to the Virtual College and Cummins Learning Center, Cummins Power South s Technical Service Centers offer traditional classroom and hands-on training to assist those individuals who feel the need for more in-depth knowledge on Cummins products. Several new programs have been added for 2013. The staff of Cummins Power South s Technical Service Centers in Tampa, FL and Atlanta, GA have a combined 100 years of Cummins and Cummins Power Generation technical knowledgeable and experience. The staff is complimented with state-of-the-art facilities and together they deliver the finest instruction available, designed specifically for Cummins products. Not only will you receive a high level of advanced technical expertise; it will also afford you the opportunity to discuss responsibilities, technical ideas, and business issues with your peers. Innovative design, advanced technology, warranty procedures, and service parts expertise are only a few of the subjects that are presented with specific product training. Now is your opportunity to prepare for the future. John H. Black Training Manager John H. Black Cummins Power South, LLC 3

Tampa & Atlanta Training Centers Tampa, FL Training Center Atlanta, GA Training Center The Tampa and Atlanta Training Centers both offer a variety of programs designed to keep pace with Cummins, Inc. and Cummins Power Generation product lines. As new emissions technology is developed in the diesel engine and power generation markets, training is the key to ensure technicians are fully prepared to address maintenance and repair of these new products. Training typically includes a balance of classroom and hands-on instruction in order to enhance the technician s learning experience. The Atlanta Training Center is located south of the Hartsfield-Jackson International Airport at 5125 Highway 85, Atlanta, GA 30349 The Tampa Technical Service Center is located adjacent to the fairgrounds at 5903-A Hampton Oaks Pkwy, Tampa, FL 33610 Maps and directions to either location are located on pages 27 & 28 of this catalog. General Information REGISTRATION: In order to avoid disappointments we recommend you enroll as soon as possible. There are three easy ways to register: FAX, Mail or Online. * FAX: You may FAX your registration form to 813-623-5442. Please complete all questions on the form prior to sending. * Mail Registration: You may always complete the enrollment form in the back of this catalog and mail to: Cummins Power South, LLC Technical Service Center 5903A Hampton Oaks Pkwy Tampa, FL 33610 * Online: http://cumminspowersouth.com/registration/registration.html CANCELLATIONS: Cancellations must be received at least two (2) working days prior to program starting date in order to avoid FULL tuition invoicing. NOTE: There will be no exceptions to this cancellation policy. 4

SCHEDULE CHANGES: Programs that had less than minimum student attendance in the past will be offered less frequently in 2012. However, should attendance in those programs exceed expectations, the Training Manager may arrange additional programs as required. A minimum of six (6) students will be required to hold special requested classes not listed on the schedule. Turnaround time for additional and/or special classes will require a minimum of thirty (30) days. COST: Tuition costs are shown along with program descriptions and are for in-house training classes only. We will accept purchase orders from established accounts, major credit cards (MC, VISA, AMEX, DISC), personal checks, and cash (not recommended). Students are responsible for their own meals, transportation, lodging, personal expenses & class supplies (pencil, pen & paper). Onsite training can be arranged with additional fees added for instructor travel expenses. LODGING: A list of recommended hotels in the respective areas is listed on page 28 of this catalog. Reservations and payment are the responsibility of each participant. TRANSPORTATION & MEALS: Cummins Power South, LLC does not provide transportation or meals for students. Rental cars are available at the Airport; limousine and taxi service is also available at a substantial cost. Public (bus) transportation is limited, and eating establishments are not within walking distance of the training centers therefore we recommend students drive or rent an automobile. DAILY SCHEDULE: Typical class hours are 8:00 a.m. to 4:00 p.m. with ample breaks and a one-hour lunch period. Some programs may dismiss early on the last day to allow for extra travel time. Qualification courses typically utilize the final two days for hands-on testing. Technicians are tested one at a time for hands-on proficiency. Due to this schedule, some technicians will complete their testing requirements on the first day of testing and thus will be released early. BOOKS, TOOLS, AND SUPPLIES: Cummins Power South, LLC provides the engine manuals (QSOL) and tools used during class. Appropriate handout literature will be given to each student and is included in the tuition cost. Due to rising literature costs, in some classes students will be given handouts in electronic format only (USB Flash Drives or CD ROM). Note pads are provided but other classroom supplies will be the student s responsibility. DRESS CODE: We recommend students wear comfortable clothing suitable for working on engines and hardware. Shorts, thongs (flip-flops), sandals, and sleeveless shirts are not considered appropriate clothing! Please dress appropriately. Cummins Power South employees should wear their work uniforms. Protective gloves will be provided for all handson activities. NOTE: Safety shoes are recommended for students attending training programs. If shop shoes are worn, a pair of shoe covers will be provided to avoid soiling carpeted areas. RECOGNITION: Certificates are awarded for satisfactory completion of programs attended at either the Atlanta or the Tampa training centers. 5

NOTES Cummins Power South, LLC Technical Service Center Training Manager John H. Black Technical Trainers Al Brown Ray Conklin Kevin Parson 6

2013 Cummins Engine Program/Course Index PROGRAM NUMBER PROGRAM DESCRIPTION DAYS COST 99-26F* ISM11 Engine Overhaul... 3.0 $900.00 99-67F* QSB Marine Engine Overhaul (Tampa Only). 3.0 $900.00 2000-01F* N14 Engine Overhaul... 3.0 $900.00 2005-06Q Cummins Warranty (N. A. Dealer Only). 1.0 N/C 2005-15Q* ISC/ISL MR NOW Overhaul 4.0 $1200.00 2006-13Q B.E.T.T.. 3.0 $900.00 2006-14Q INSITE SOFTWARE.... 2.0 $600.00 2006-36F ISB6.7 Rear Gear Train Engine Overhaul.. 3.0 $900.00 2006-37F ISC8.3/ISL9 CM850 HPCR Engine Overhaul.. 3.0 $900.00 2006-48/57Q* CMD MR/HD Marine Qual (Tampa Only).. 5.0 $1500.00 2007-28Q* ISL9-G CM2180 CNG Engine Qual. 4.0 $1200.00 07-30/10-07Q* Zeus/SmartCraft 2.2 Qualification... 4.0 $1200.00 2006-30/2009-37Q EPA 2007/2010 ISX15 CM871/CM2250 Qual.... 5.0 $1625.00 2009-37Q EPA 2010 ISX15 CM2250 Engine Qual... 4.0 $1325.00 2009-30/31Q EPA 2010 ISB/ISC/ISL CM2250 Engine Qual 4.0 $1325.00 2009-30/31/37Q EPA 2010 MR/ISX15 CM2250 Combo Engine Qual 5.0 $1625.00 2010-06Q EPA 2010 ISX11.9 CM2250 Engine Qual.. 4.0 $1200.00 2010-16/17Q QSB6.7/QSL9 CM2250 Tier IV Industrial Qual.. 4.0 $1200.00 2011-13Q QSB6.7 Marine Engine Qual....... 5.0 $1500.00 2011-15Q ISX15 CM570/870/871/2250 Block Mach Qual... 4.0 $1200.00 2011-17Q* ISX15 NOW Overhaul W/Static Injection Timing 5.0 $1500.00 2012-22/24/25Q 2013 CM2350 MR/HD Update Qual. (NEW) 3.0 $900.00 2012-25Q 2013 CM2350 Update Qual. Navistar Only (NEW) 4.0 $1200.00 2012-35Q ISX12-G CNG Engine Qual. (NEW). 4.0 $1200.00 3122 ISX15 CM871 Injection Timing Qual... 1.0 $300.00 7005/7006 Vessel/SmartCraft Electronics 2.0 $600.00 AG-101 Natural Gas Vehicle Fuel Delivery System (NEW)...5 $200 *NOTE: Classes that have traditionally had little or no participation in past years will not be scheduled in 2013. However these classes can be added by special request. Special Classes can also be arranged at your location(s) or at the Cummins Power South, LLC Training Center(s) by special request. These classes will be subject to minimum attendance requirements, and available dates. Contact the Tampa Technical Service Center for further details. 7

2013 Cummins Engine Training Schedule LEGEND: BOLD TEXT = CLASSES HELD IN ATLANTA, GA NORMAL TEXT = CLASSES HELD IN TAMPA, FL JANUARY FEBRUARY 22 2012-22/24/25Q 2013 Update (Excluding Navistar) 05 3122 ISX15 Static Timing 05 2010-06Q ISX11.9 CM2250 Qual 06 2012-22/24/25Q 2013 Update (Excluding Navistar) 26 2012-22/24/25Q 2013 Update (Excluding Navistar) MARCH APRIL 04 3122 ISX15 Static Timing 01 2006-13Q B.E.T.T. 05 2011-15Q ISX Mid-Stop Counterbore Mach. 04 2006-14Q INSITE Software Qualification 11 2012-22/24/25Q 2013 Update (Excluding Navistar) 08 2006-13Q B.E.T.T. 11 AG-101 Vehicle CNG Fuel Delivery Sys 09 3122 ISX15 Static Timing 12 2007-28Q ISL9-G Engine Qualification 10 2012-22/24/25Q 2013 Update (Excluding Navistar) 18 2006-31Q 07 ISX Qualification (Navistar) 11 2006-14Q INSITE Software Qualification 19 2012-25Q 2010/2013 ISX Qual (Navistar) 23 3122 ISX15 Static Timing 19 2010-06Q ISX11.9 CM2250 Qual 24 2012-22/24/25Q 2013 Update (Excluding Navistar) 25 2006-48/57Q CMD MR/HD Marine Qualification 30 2012-25Q 2010/2013 ISX Qual (Navistar) 25 AG-101 Vehicle CNG Fuel Delivery Sys 26 2007-28Q ISL9-G Engine Qualification MAY JUNE 06 1999-26F ISM11 Engine Overhaul 03 2011-13Q QSB6.7 Marine Engine Qual 14 2012-22/24/25Q 2013 Update (Excluding Navistar) 03 AG-101 Vehicle CNG Fuel Delivery Sys 21 2012-25Q 2010/2013 ISX Qual (Navistar) 04 2012-35Q ISX12-G Engine Qualification 29 2006-36F ISB-RGT HPCR Engine Overhaul 10 2011-13Q QSB6.7 Marine Engine Qual 10 3122 ISX15 Static Timing 11 2012-22/24/25Q 2013 Update (Excluding Navistar) 17 2011-13Q QSB6.7 Marine Engine Qual 24 AG-101 Vehicle CNG Fuel Delivery Sys 25 2012-35Q ISX12-G Engine Qualification 25 2012-25Q 2010/2013 ISX Qual (Navistar) ISL9 CM2250 8

2013 Cummins Engine Training Schedule JULY AUGUST 02 3122 ISX15 Static Timing 05 2009-30/31/37Q 2010 MR/HD Combo Qual 08 2012-22/24/25Q 2013 Update (Excluding Navistar) 13 2012-22/24/25Q 2013 Update (Excluding Navistar) 08 2007-30/10-07Q Zeus Midrange and QSM11 19 2006-48/57Q CMD MR/HD Marine Qualification 22 2012-22/24/25Q 2013 Update (Excluding Navistar) 20 2012-22/24/25Q 2013 Update (Excluding Navistar) 25 3122 ISX15 Static Timing 26 2007-30/10-07Q Zeus Midrange and QSM11 29 2007-30/10-07Q Zeus Midrange and QSM11 26 2006-37F ISC/ISL HPCR Overhaul 30 2009-30/31/37Q 2010 MR/HD Combo Qual SEPTEMBER OCTOBER 04 2012-22/24/25Q 2013 Update (Excluding Navistar) 01 2012-22/24/25Q 2013 Update (Excluding Navistar) 09 2006-36F ISB-RGT HPCR Engine Overhaul 14 3122 ISX15 Static Timing 09 AG-101 Vehicle CNG Fuel Delivery Sys 15 2012-22/24/25Q 2013 Update (Excluding Navistar) 10 2007-28Q ISL9-G Engine Qualification 28 2009-30/31/37Q 2010 MR/HD Combo Qual 23 2010-06Q ISX11.9 CM2250 Engine Qual 23 AG-101 Vehicle CNG Fuel Delivery Sys 24 2007-28Q ISL9-G Engine Qualification NOVEMBER DECEMBER 05 2010-06Q ISX11.9 CM2250 Engine Qual 09 2009-30/31/37Q 2010 MR/HD Combo Qual 11 2012-22/24/25Q 2013 Update (Excluding Navistar) Cummins Warranty Training Schedule MARCH SEPTEMBER 08 2005-06Q Cummins Warranty 20 2005-06Q Cummins Warranty 15 2005-06Q Cummins Warranty 27 2005-06Q Cummins Warranty JUNE DECEMBER 07 2005-06Q Cummins Warranty 06 2005-06Q Cummins Warranty 14 2005-06Q Cummins Warranty 13 2005-06Q Cummins Warranty NOTE : The above dates are subject to change without notice Cummins Power South Training Center Tampa, FL 9

Cummins Course Descriptions NOTE: Courses with mandatory prerequisites MUST have the prerequisites completed and uploaded to QuickServe Online at least two weeks prior to the scheduled class unless special arrangements are made with the Technical Service Center staff. Students who arrive for class and do not have ALL prerequisites complete will be sent home and charged a no-show fee of $50.00 99-26F ISM Engine Overhaul Distributor and dealer technicians will perform disassembly and re-assembly procedures on the ISM engine relative to overhaul requirements. Component failure analysis will also be covered to ensure technician competence during the overhaul process. 3.0 Days (6 students) $900.00 99-67F QSB Marine Engine Overhaul Distributor and dealer technicians will perform disassembly and re-assembly procedures on the QSB Marine electronic engine relative to overhaul requirements. Component failure analysis will also be covered to ensure technician competence during the overhaul process 3.0 Days (6 students) $900.00 2000-01F N14 Engine Overhaul Distributor and dealer technicians will perform disassembly and re-assembly procedures on the N14 electronic engine relative to overhaul requirements. Component failure analysis will also be covered to ensure technician competence during the overhaul process. 3.0 Days (6 students) $900.00 2005-06Q Cummins Warranty (North American Dealer Only) This program has been developed to qualify Distributor/Dealer personnel to administer Cummins Warranty and Customized Assurance Plan (CAP) repairs with the Cummins RAPIDSERVE warranty system. * CVC Warranty Library (Smart Program Guide) 1.0 Day (15 students) N/C 2005-15Q* ISC8.3/ISL8.9 NOW Overhaul This course is designed to teach technicians Cummins National Overhaul Warranty (NOW) practices with regard to NOW Plan Content & NOW inspection & reuse guidelines relating to the ISC8.3 and ISL9 engine platforms. Completion of the NOW Warranty Certificate will also be covered. * B.E.T.T. - Classroom or HD CVC Library or MR CVC Library (Smart Program Guide) INSITE 7.5 - Classroom or HD CVC Library or MR CVC Library (Smart Program Guide) ISC/ISL CM2150 Full Service Qualification Program 2006-39Q (Smart Program Guide) 4.0 Days (6 students) $1200.00 10

2006-13Q B.E.T.T. (Classroom) This course offers an alternative learning experience to the Cummins Virtual College Multimedia course. Technicians struggling with the multimedia self study philosophy will receive instructor assistance relative to the virtual handson portion of the program. The Virtual College course will be covered beginning to end as students learn digital meter usage, ohms law and basic electronic troubleshooting skills. This course is a pre-requisite for all electronically controlled Cummins engine qualification courses. 3 Days (6 students) $900.00 2006-14Q INSITE Software Version 7.X (Classroom) Many technicians require additional instruction as a supplement to the INSITE CD-ROM program. Others prefer this as an alternative to secure qualification status for INSITE-Version 6. This program was developed to provide instructor assisted qualification for the Cummins computer based software program. Hands-on practical application will be a constant requirement during this advanced program. Upon successful completion by distributor/dealer technician, full qualification status will be earned. This course is a pre-requisite for all electronically controlled Cummins engine qualification courses. 2.0 Days (6 students) $600.00 2006-36F ISB (Rear Gear Train) Engine Overhaul This course is designed to familiarize technicians with the ISB engines equipped with the rear gear train. Overhaul practices and guidelines are taught with close attention to assembly procedures and specifications. Special attention will be given to critical areas such as overhead adjustment, fuel pump installation and the new components related to rear gear train, EGR and VGT technology. 3.0 Days (6 students) $900.00 2006-37F ISC/ISL HPCR Engine Overhaul This course is designed to familiarize technicians with the ISB/ISC/ISL HPCR engines with regard to overhaul practices and guidelines with close attention to assembly procedures and specifications. Special attention will be given to critical areas such as overhead adjustment, fuel pump installation and the new components related to EGR and VGT technology. 3.0 Days (6 students) $900.00 2006-48/57Q CMD MidRange & Heavy Duty Marine Qualification This course is designed for Cummins distributor and dealer marine technicians. Upon successful completion of this course, technicians should be competent with respect to identification of marine specific engine components, maintenance requirements, unique troubleshooting techniques, basic start-up & sea trial techniques, basic engine/vessel application and vessel installation requirements for electronically controlled marine engines. This course does not cover pre-smartcraft electronics or the CMD SmartCraft system and displays. This course, along with courses 7005/7006 and Vessel/SmartCraft 2.2 electronics are required for marine dealers to become certified (green profile) for CMD product support. Note: Technicians must complete ALL of the mandatory prerequisites listed below. Vessel Electronics/SmartCraft 2.2 Classroom Course(s) 7005/7006 are not a mandatory prerequisite to attend this course however they will be required to accomplish the MR/HD Marine Technician Qualification, and must be completed for the overall qualification to be applied to a technician s profile. Marine Vessel Performance - CVC Library Gen-14 B.E.T.T. - Classroom or CVC (Smart Program Guide) INSITE 7.X - Classroom or CVC (Smart Program Guide) QSOL and Clean Care - CVC Library Gen-12 ISM Engine - CVC HD Library GEN-8, GEN-11, HD-8 & HD-11 Special Tests HD-1, HD-2, HD-3 (QSOL Online Tests) 5 Days (6 students) $1500.00 11

2007-28Q ISL-G CM2180 (CNG) Engine Qualification This course is designed to introduce technicians to the Cummins ISL-G CNG CM2180 engine and controls. Topics include Natural Gas safety, Engine and Controls Familiarization, Maintenance guidelines and engine/controls diagnostics. Recommended Prerequisites: Natural Gas Vehicle Fuel Delivery Systems (Agility) Course AG-101 B.E.T.T. - Classroom or CVC (Smart Program Guide) INSITE - Classroom or CVC (Smart Program Guide) Alternative Fuels Library (Smart Program Guide) 4.0 Days (6 students) $1200.00 2007-30Q Zeus/SmartCraft 2.2 Marine Propulsion System Qualification 2010-07Q This course is designed for Cummins distributor and dealer marine technicians and is required to perform warranty repairs on Zeus marine Pod drive products and systems with QSB, QSC, QSL and QSM marine engines. Upon successful completion of this course, technicians will become competent with identification of Pod components, specific maintenance requirements, unique troubleshooting techniques, Pod start-up/set-up procedures and basic operation of the Pod system. Course focuses heavily on the SmartCraft v2.2 electronics systems and diagnostics, CAN data networks, helm controls and operation, navigation device inputs, multi-station helm operation and specific installation requirements for Pod drives. Students will further their understanding through the disassembly and assembly of a complete Zeus Pod, overview of system architecture, electronic inputs/outputs, mechanical/hydraulic steering/tab system. Vessel View display operation and programming procedures are also covered in this course. The CDS G3 tool will also be discussed and used for troubleshooting and diagnostics of the SmartCraft control system, module flash, and helm set-up procedures. Note: Technicians must complete ALL of the mandatory prerequisites listed below, some prerequisites are separate courses and will require completion for the overall qualification to be applied to a technician s profile. Marine Vessel Performance - CVC - Gen-14 B.E.T.T. - Classroom or CVC (Smart Program Guide) INSITE 7.X - Classroom or CVC (Smart Program Guide) QSOL and Clean Care - CVC Library Gen-12 ISM Engine CVC HD Library GEN-8, GEN-11, HD-8 & HD-11) Special tests HD-1, HD-2, HD-3 (QSOL Online Tests) Vessel Electronics/SmartCraft 2.2 - Classroom Course 2006-48/57Q CMD Midrange & Heavy Duty Marine Qualification - Classroom Course 4.0 Days (6 students) $1200.00 2006-30/2009-37Q EPA 2007/2010 ISX15 CM871/CM2250 Engine Qualification This course is a required course for any technician wishing to obtain certification on the 2007 and 2010 EPA certified Cummins ISX CM871 and ISX CM2250 engine. This course offers technicians who are not previously qualified on the 2007 ISX product a means to combine both the 2007 ISX and the 2010 ISX qualification into one course. The course utilizes a combination of classroom and hands-on activities designed to review and enhance the material studied in the Cummins Virtual Library course. At the conclusion of classroom training each technician will undergo hands-on testing and upon successful completion will be granted Qualification status. Upon successful completion of this course technicians will be rewarded with a complete electrical wiring test lead kit, a value of over $250. * Cummins Virtual College Heavy Duty Library for the ISX CM871 and CM2250 (Smart Program Guide) 5 Days (6 students) $1625.00 12

2009-37Q EPA 2010 Heavy Duty (ISX15 CM2250) Engine Qualification This course is a required course for any Cummins distributor or dealer technician prior to performing warranty repairs on Cummins ISX15 CM2250 automotive engines. The course is a combination of classroom and hands-on activities designed to enhance the material in the Cummins Virtual Library course. Each technician will undergo hands-on testing and upon successful completion will be granted Qualification status. Technicians who successfully complete this qualification course will receive a electronic copy of all handouts via a USB flash drive and a Cummins wiring test lead kit P/N4919115 valued over $250. NOTE: Technicians attending this course MUST be 2007 ISX CM871 Qualified. Technicians attending this course will be tested on the 2010 HD Virtual Library content on the first day of class. It is essential they pay attention to the material as they go through the CVC especially sections dealing with DEF (Diesel Exhaust Fluid) and it s control system. Cummins Virtual Library relative to the EPA 2010 ISX15 CM2250 (Smart Program Guide) 2007 EPA ISX CM871 Full Service Qualification (CVC, Classroom & Hands-On) 4.0 Days (6 students) $1325.00 2009-30/31Q EPA 2010 MidRange CM2250 Engine Qualification This course is a required course for any distributor or dealer technician prior to performing warranty repairs on any Cummins ISB/ISC/ISL CM2250 automotive engine. The course is a combination of classroom and hands-on activities designed to enhance the material the Cummins Virtual Library course. Each technician will undergo handson testing and upon successful completion will be granted Qualification status. NOTE: Technicians attending this course will be tested on the 2010 Midrange Virtual Library content on the first day of class. It is essential they pay attention to the material as they go through the CVC especially sections dealing with DEF (Diesel Exhaust Fluid). NOTE II: Technicians who successfully complete this qualification course will receive a electronic copy of all handouts via a USB flash drive and a Cummins wiring test lead kit P/N4919115. Cummins Virtual Library relative to the EPA 2007 & 2010 Midrange engines 4.0 Days (6 students) $1325.00 2009-30/31/37Q EPA 2010 Combination MR/HD CM2250 Engine Qualification This course is required for any distributor or dealer technician in order to perform warranty repairs on any Cummins ISB/ISC/ISL CM2250 and/or ISX15 CM2250 automotive engine manufactured to 2010 EPA/CARB specifications. The course is a combination of classroom and hands-on activities designed to enhance the material the Cummins Virtual Library course. Each technician will undergo hands-on testing and upon successful completion will be granted Qualification status. NOTE: Technicians attending this course MUST be 2007 ISX CM871 Qualified. Technicians attending this course will be tested on the both the 2010 MR and 2010 HD Virtual Library content on the first day of class. It is essential they pay attention to the material as they go through the CVC especially sections dealing with DEF (Diesel Exhaust Fluid). NOTE II: Technicians who successfully complete this qualification course will receive a electronic copy of all handouts via a USB flash drive and a Cummins wiring test lead kit P/N4919115. 2007 EPA HD Technician Qualification (CVC, Classroom & Hands-On) Cummins Virtual Library Courses relative to the EPA 2010 MR & HD engines 5.0 Days (6 students) $1625.00 13

2010-06Q EPA 2010 ISX11.9 CM2250 Engine Qualification This course is required for any distributor or dealer technician in order to perform warranty repairs on any Cummins ISX11.9 CM2250 automotive engine manufactured to 2010 EPA/CARB specifications. The course is a combination of classroom and hands-on activities designed to enhance the material the Cummins Virtual Library course. Each technician will undergo hands-on testing and upon successful completion will be granted Qualification status. NOTE: Technicians attending this course MUST be 2010 ISX CM2250 Qualified. Technicians attending this course will be tested on the both the 2010 ISX11.9 HD Virtual Library content and on the material presented during the class. It is essential they pay attention to the material as they go through the CVC especially sections dealing with DEF (Diesel Exhaust Fluid). NOTE II: Technicians who successfully complete this qualification course will receive a electronic copy of all handouts via a USB flash drive. 2010 EPA HD Technician Qualification (CVC, Classroom & Hands-On) Cummins Virtual Library Courses relative to the EPA 2010 ISX11.9 CM2250 engine 4.0 Days (6 students) $1200.00 2010-16/17Q QSB6.7/QSC8.3/QSL9 Tier IV Industrial Qualification This course is a required course for any distributor or dealer technician in order to perform warranty repairs on any Cummins QSB/QSL CM2250 Tier 4i industrial engines built to 2010 EPA/CARB specifications. This is generally the final step in a midrange industrial technician s initial qualification process. After completing the Cummins Virtual College Midrange Library (B/N 4091858) prerequisites, the technician must successfully complete this 5 Day classroom course/ hands-on diagnostic evaluation. The hands on, testing portion is performed on a live engine module and upon successful completion will be granted Qualification status. This is a test of the technician s ability in diagnostics and repair using the latest INSITE software, basic electronics troubleshooting skills and base knowledge of the subject engine and systems. Cummins Virtual College Midrange Library (4091858) 4.0 Days (6 students) $1200.00 2011-13Q QSB6.7 Marine Engine Qual This class is for the marine technician who wishes to become qualified on the QSB6.7 CM2250 marine engine released in the first quarter of 2012. Along with the engine qualification, the technician will also be introduced to the SmartCraft 2.5 electronic controls system and the G3 diagnostic tool. This course is a stand-alone course and does not require the technician to be qualified in any previous marine product however B.E.T.T., Insite and a variety of Cummins Virtual College and online training courses are required prerequisites (see smart program guide) 5.0 Days (6 students) $1500.00 2011-15Q ISX15 Mid-Stop Counterbore Ledge Cutting Qual This course was created for the technician already qualified on the ISX/QSX 15 liter engine. Recent issues with the cylinder head to engine block joint/head gasket seal, has resulted in the discovery of potential defects with the midstop Counterbore ledge on some ISX15 cylinder blocks. Machining the Counterbore ledge is the only accepted method of correcting the defect. This course will teach the technician proper tool assembly and inspection along with proper procedure and techniques for precisely machining the mid-stop Counterbore ledge to proper specifications. This course is not mandatory for Cummins ISX qualified technicians. However, if it becomes necessary to repair a Counterbore issue on a ISX15 engine block, a qualified technician MUST perform the repair. If a ISX15 qualified technician has not completed the mid-stop Counterbore machinist qualification course, his/her qualification status will turn yellow. However this will not affect the technician's ability to perform warranty repairs not associated with the Counterbore defect. The technician's status will remain yellow indefinitely or until such time as the technician completes the machinist qualification. 4.0 Days (6 students) $1200.00 14

2011-17Q ISX15 NOW Overhaul W/Static Injection Timing This course is designed to teach technicians Cummins National Overhaul Warranty (NOW) practices with regard to NOW Plan Content & NOW inspection & reuse guidelines relating to the ISX15 engine platform. The class has been extended this year to include the new Static Injection Timing process. Completion of the NOW Warranty Certificate will also be covered. 5.0 Days (6 students) $1500.00 2012-22/24/25Q 2013 CM2350 Update Qual (NEW) Distributor/Dealer Qualification course on EPA 2013 MidRange and Heavy Duty CM2350 engines. This course is required for full-service level technicians in order to perform warranty repairs on the ISX15, ISX12, ISB6.7 and/or ISL9 CM2350 on-highway engines. Topics include electrical and mechanical sub-systems, exhaust After treatment, including: Diesel Oxidization Catalyst, Diesel Particulate, Selective Catalytic Reduction, On Board Diagnostics, and the new Expert Diagnostic System. 2010 EPA MR and/or HD CM2250 Technician Qualification (CVC, Classroom & Hands-On) 2010 ISX12 CM2250 Technician Qualification Cummins Virtual Library Courses relative to the EPA 2013 HD & MR CM2350 engine 3.0 Days (6 students) $900.00 2012-25Q 2010/2013 CM2350 Update Qual Navistar Only (NEW) This course is required for full-service level Navistar technicians in order to perform warranty repairs on the 2013 Cummins ISX15 CM2350 X101 EPA automotive product. The ISX15 CM2350, introduced January 2013 is the newest EPA compliant on-highway engine. Topics include electrical and mechanical sub-systems, exhaust After treatment, including: Diesel Oxidization Catalyst, Diesel Particulate, Selective Catalytic Reduction, On Board Diagnostics and the new Expert Diagnostic System 2007 EPA ISX15 CM871 Technician Qualification (CVC, Classroom & Hands-On) Cummins Virtual Library Courses relative to the EPA 2013 HD CM2350 engine (see smart program guide) 4.0 Days (6 students) $1200 2012-35Q ISX12-G CM2180 CNG Engine Qual This course is designed to introduce technicians to the Cummins ISX12-G CM2180 Compressed Natural Gas engine and controls. Topics include Natural Gas safety, Engine and Controls Familiarization, Maintenance guidelines and engine/controls diagnostics. Technicians who successfully complete this course may also qualify for the ISL9 CM2180 CNG engine by completing the necessary Cummins Virtual College courses and the ISX12 CM2250 diesel engine qualification course. Recommend Prerequisites: Natural Gas Vehicle Fuel Delivery Systems (Agility) Course AG-101 ISX12 CM2250 Technician Qualification course (CVC, Classroom & Hands-On) Cummins Virtual Library courses relative to the ISX12-G CM2180 (see smart program guide) 4.0 Days (6 students) $1200.00 15

3122 ISX15 CM570/CM870/CM871 Static Injection Timing Qualification This course is optional for any distributor or dealer technician already qualified on the ISX15 CM570, CM870 and/or CM871 engine. A technician s scorecard will show yellow for this course until they have completed the course. Since this is an optional course, their status will not turn red and their current qualification status will not expire. Their status will turn green upon completion of this course. A technician attending this class must successfully complete the classroom and testing phases of this course. Testing includes a written test and a hands-on qualification. 1.0 Days (3 students) $300.00 7005/7006 Vessel / SmartCraft 2.2 Electronics SmartCraft 2.2 electronics is the latest in the evolution of CMD engine/vessel control systems. SmartCraft 2.2 is the current electronics system for all Quantum B,C,D,L & M series engines as well as Zeus and Axius propulsion products. This course is designed for Cummins distributor and dealer marine technicians and is required to perform warranty repairs on current Quantum marine products. This class will focus on the architecture of all the systems from SmartCraft 1.0 through to the latest 2.2 architecture. Focus for this class will be on Inboard and sterndrive products that use the DTS and Non-DTS systems in vessel applications. The course will have limited discussion of Zeus/Axius as these systems are covered in more detail in other related classes. This course is also required along with 2006-48/57Q CMD Midrange & Heavy Duty Marine Qualification for marine dealers to become certified (green profile) for CMD product support. Note: Technicians must complete ALL of the mandatory prerequisites listed below, some prerequisites are separate courses and will require completion for the overall qualification to be applied to a technician s profile. B.E.T.T. - Classroom or CVC (B/N 4091840) INSITE 7.X - Classroom or CVC (B/N 4091839) 2.0 Days $600.00 AG-101 Vehicle Fuel Delivery Systems for Natural Gas Powered Vehicles While not a required course for CNG engine qualification, this course is highly recommended as a prequel to the ISL- G and/or ISX12-G CM2180 qualification courses. This course covers extensively the Agility Fuel Delivery System. Agility is the manufacturer of the fuel delivery system used on 90% of the CNG powered vehicles in use today. This course utilizes information and hardware from Agility to help the engine technician understand all aspects of the CNG fueled vehicle. Fuel tank design, safety and maintenance of the OEM side components are discussed..5 Days (6 students) $200.00 16

2013 Cummins Power Generation Program/Course Index Industrial Product PROGRAM NUMBER COURSE DESCRIPTION DAYS COST 1995-29Q Large Commercial Product... 4.0 $1200.00 2000-04Q BT (Power Sentry Controls) Transfer Switch. 2.0 $600.00 2000-05Q LT/LC ATS Qualification. 3.0 $900.00 2000-18/08-14Q OTPC Spec A 40-1000 AMP & OTEC ATS Qual.. 3.0 $900.00 2000-19Q PowerCommand Control 3200/3201 Qual.. 3.0 $900.00 2000-20Q InPower Software Qual... 2.0 $600.00 2001-28Q PowerCommand Control 2100 Qual 2.0 $600.00 2001-29Q OHPC/CHPC Transfer Switch Qual... 3.0 $900.00 2001-30Q BTPC Automatic Transfer Switch Qual. 2.0 $600.00 2001-32F Cummins Power Generation (Onan) Warranty... 1.0 N/C 2002-44Q PowerCommand Control 3100 Qual.. 2.0 $600.00 2004-14/15Q FT-10 Networks Basic & Intermediate Qual. 5.0 $1500.00 2004-16Q FT-10 Advanced Networks. 5.0 $2250.00 2005-13Q MCM 3320 Paralleling Control.. 3.0 $900.00 2008-08/13Q PowerCommand Controls 1.X & 2.X Qual 5.0 $1500.00 2008-14Q OTEC Transfer Switch & Controls Qual.. 2.0 $600.00 2008-18/19Q PowerCommand Control 3.3 Qual with 2011-02Q 3.3 Hydra-Mech Update.. 5.0 $1500.00 2009-43Q NSPS EPA Emissions Performance Standards Qual 2.0 $800.00 2010-02Q OT Transfer Switch 1500A Mech.. 1.0 $300.00 2010-03Q PSI Gas Genset Engine Qual. 3.0 $1050.00 2011-08Q BTPC (GEZ) 1600-3000A Transfer Switch.. 2.0 $800.00 2011-25Q DMC 1500 Controls Qualification. 5.0 $1750.00 17

2012-XXQ Engine Fundamentals. 5.0 $1500.00 2012-XXQ Generator Fundamentals.. 5.0 $1500.00 2012-XXQ Transfer Switch Fundamentals 5.0 $1500.00 2012-XXQ AC Generator Fundamentals. 5.0 $1500.00 2012-44Q EPA Tier IV Qual 3.0 $1050.00 C-177 Fundamentals of Power Generation. 3.0 $900.00 C-500 Insite for PowerGen Technicians (NEW). 2.0 $600.00 C-501 New ATS Product Intro for 2011 (NEW) 1.0 $300.00 C-502* OT-III ATS Controls (Vintage Switchgear) 2.0 $600.00 C-504 Aftermarket Conversions Upgrade. 1.0 $400.00 18

2013 Cummins Power Generation Program/Course Index Consumer Product PROGRAM NUMBER COURSE DESCRIPTION DAYS COST 2007-08Q RV Gas Full Service Qual... 5.0 $1500.00 2007-10/2009-26Q RV Diesel Full Service Qual..... 5.0 $1500.00 2007-12/14Q Marine Gas & Diesel Full Service Qual... 5.0 $1650.00 2007-16/18/23Q Commercial Mobil Full Service Qual 5.0 $1500.00 2007-21Q* ComfortGuard Qual.. 3.0 $900.00 2009-20Q CPG RS Liquid Cooled Genset Qual.... 5.0 $1500.00 2009-23Q CPG RS Air Cooled Genset Qual.. 3.0 $900.00 2009-28Q RV HQD Full Service Qual 5.0 $1500.00 2009-42Q 20kW CMSD Full Service Qual 2.0 $600.00 C-503 Onan/John Deere Marine Engine Qual 5.0 $TBD C-6029 InPower Onan Service Software... 1.0 $300.00 *NOTE: Classes that have traditionally had little or no participation in past years will not be scheduled in 2011. However these classes can be added by special request. Special Classes can also be arranged at your location(s) or at the Cummins Power South, LLC Training Center(s) by special request. These classes will be subject to minimum attendance requirements, and available dates. Contact the Tampa Technical Service Center for further details. 19

2013 Cummins Power Generation Training Schedule LEGEND: BOLD TEXT = CLASSES HELD IN ATLANTA, GA NORMAL TEXT = CLASSES HELD IN TAMPA, FL JANUARY FEBRUARY 15 2000-20Q INPOWER 04 2000-18/08-14Q OTEC/OTPC ATS 17 C-500 INSITE for Powergen 07 2001-30Q BTPC ATS 28 2000-05Q LT/LC ATS Qual 12 2000-20Q INPOWER 31 2008-14Q OTEC ATS Control 18 C-177 Fundamentals of Powergen MARCH APRIL 05 2009-23Q RS AIR Cooled H/S 23 2000-19Q PCC3200/3201 Controls 29 2011-25Q DMC-1500 MAY JUNE 13 2009-28Q RV HQD Full Service Qual 03 2007-08Q RV Full Service Gas 20 2011-25Q DMC-1500 10 2007-16/18/23Q Commercial Mobil Full Service 17 07-10/2009-26Q RV Full Service Diesel 24 2004-14/15Q FT-10 Basic & Intermediate Ntwks JULY AUGUST 01 2011-08Q BTPC (GEZ) 1600-3000A 06 XXXX-XXQ EPA Tier IV Qual 22 2007-16/18/23Q Commercial Mobil Full Service 12 2001-28Q PCC2101 Controls 29 2004-16Q FT-10 Advanced Networks 14 2000-19Q PCC3200/3201 Controls 20 XXXX-XXQ EPA Tier IV Qual 26 2008-08/13Q PCC 1.x & 2.x Controls Qual. SEPTEMBER OCTOBER 09 XXXX-XXQ Engine Fundamentals 07 XXXX-XXQ Generator Fundamentaos 30 XXXX-XXQ PCC 3.3 w/hydra Update 14 2000-18/08-14Q OTEC/OTPC ATS 17 2008-14Q OTEC ATS Control 21 XXXX-XXQ Transfer Switch Fundamentals NOVEMBER DECEMBER 04 XXXX-XXQ Engine Fundamentals 03 2009-43Q NSPS EPA Emissions Perf 18 XXXX-XXQ Transfer Switch Fundamentals 09 XXXX-XXQ PCC 3.3 w/hydra Update Special Classes: Special Classes, can be arranged at your location or at the Cummins Power South, LLC Training Centers for a nominal fee. The classes will be subject to minimum attendance requirements and available dates. Contact the Technical Service Center at (813) 635-5701 for further details. 20

Cummins Power Generation Program/Course Descriptions 1995-29Q Industrial - Large Commercial Product This program covers power generation sets 20 kw and larger. Specific topics include theory of operation, troubleshooting and repair of Detector Control, Newage generators, and voltage regulators. Technicians will use electrical schematics, meters, and service publications to perform hands-on troubleshooting exercises on live generators. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. Mandatory Prerequisites (for Cummins PowerSouth Technicians): CORE Course Program Large Commercial Products Assessment on PGU (CMT0626-EN-TST) 4.0 Days (6 students) $1200.00 2000-18/08-24Q Industrial - OTPC Spec A 40-1000 Amp & OTEC ATS Qualification The OTPC Automatic Transfer Switch (ATS) has been designed as an upgrade and replacement for the OTIII ATS. This program will focus on the similarities and differences between both of these switches. Specific topics are operation of the microprocessor-based switches and hands-on troubleshooting. Specific information covering the OTEC control module will be covered. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. NOTE: Each student MUST bring a laptop computer with InPower software installed. InPower Software (classroom) CORE Course Program OTPC 40-1000 Amp Assessment on PGU (CMT0639-EN-TST) 3.0 Days (6 students) $900.00 2000-19Q Industrial - PowerCommand Control 3200/3201 Qualification This course is designed to introduce technicians to the PowerCommand Control 3200 used initially on generator sets powered by the QSK15 QSK45 and QSK60 Quantum engines. Generator set control hardware location and module functions are the primary training objectives. This course also includes an introduction to the GCS module used by Generator OEMs in building G-Drive generator sets. This course will also include the PowerCommand Network module used with the PowerCommand Control 3200, and the paralleling parameter adjustments for both isolated and infinite bus paralleling systems. InPower software and other new service tools will be used during the hands-on Troubleshooting portion of this course. Upon completing the classroom exercises students will participate in a written and hands-on qualification assessment. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. NOTE: Each student MUST bring a laptop computer with InPower software installed. Mandatory Prerequisites (for Cummins PowerSouth Technicians): CORE Course Program PCC 3200 Assessment on PGU (CMT0641-EN-TST) InPower Software (classroom) And any one of the following programs QSK45/60 Virtual College CD-ROM (BN 3898777) QSX-15 Engine Virtual College CD-ROM (BN 3898887) 3.0 Days (4 students) $900.00 21

2000-20Q Industrial - InPower Software Qualification This program is designed to introduce generator technicians to the electronic service tool InPower. The program will concentrate on software installation on laptop computers, operation of InPower, performing tests, and calibration of power equipment. Most of the program will be instructor-led hands-on tasks. This program will be a prerequisite for many future products. This course is also available on the PGU Web Site. NOTE: Technicians are required to bring a laptop computer that has at least one serial port and Windows XP, or Windows Vista installed. InPower software MUST be purchased prior to class date. Contact Teresa Bradberry at (404) 765-5120 to arrange software purchase 30 days in advance of class. Mandatory Prerequisites (for Cummins PowerSouth Technicians): InPower Assessment on PGU (CMT0129-EN-TST) 2.0 Days (6 students) $600.00 2001-28Q Industrial - PowerCommand Control 2100 Qualification This course is designed enable technicians to perform service and repairs on the PowerCommand Control 2100 & 2101 with CAN link(j-1939) communication. The technicians will learn the features and menus, location of generator set control hardware and functionality of control modules. Students will also learn the complete sequencing operation of all of the modes in the PowerCommand Control 2101 operating systems. Installation procedures for generator sets with the PowerCommand Control 2101 will also be discussed. Upon completion of classroom studies, students will participate in hands-on troubleshooting practice. InPower service software and other tools will be used during the hands-on Troubleshooting portion of this course. Upon completion of all of the required classroom exercises, students will participate in a written and hands-on qualification assessment. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. NOTE: Each student MUST bring a laptop computer with InPower software installed. InPower Software Qualification Core Course Program 2.0 Days (6 students) $600.00 2001-29Q Industrial - OHPC/CHPC ATS Qualification This course will cover the new Closed Transition PowerCommand Automatic Transfer Switch, its options, and the new actuator mechanism. Participants will be performing in-class, and hands-on exercises to complete this course. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. NOTE: Each student MUST bring a laptop computer with InPower software installed. InPower Software Qualification OTPC Transfer Switch (classroom) Core Course Program 3.0 Days (6 students) $900.00 22

2001-30Q Industrial - BTPC Qualification This course is designed to enable technicians to perform service and repairs on the new PowerCommand Control Bypass Transfer Switch. Lessons will include the Automatic and Bypass switch mechanisms. Hands-On exercises will focus on automatic and manual control of the ATS, racking out the automatic switch and troubleshooting common fault situations. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. NOTE: Each student is required to provide his/her own laptop with InPower Software installed. InPower Software (classroom) OTPC Transfer Switch (classroom) CORE Course Program BTPC Assessment on PGU (CMT0692-EN-TST) 2.0 Days (6 students) $600.00 2001-32F Cummins Power Generation (Onan) Warranty This program is designed to familiarize Cummins Power Generation/Onan dealers with the methods of handling warranty claims for repairs on all Cummins Power Generation products. 1.0 Day (15 students) N/C 2002-44Q Industrial - PowerCommand Control 3100 Qualification This course concentrates on installation, operation, adjustment and troubleshooting of the original PowerCommand Control. We will review the menu systems as well as voltage regulator and governor adjustments. Upon completion of the classroom instruction, students will participate in a written and hands-on qualification assessment. QST30 Genset engine CVC (BN 3898577) Core Course Program PCC 3100 Assessment on PGU (CMT0551-EN-TST) 2.0 Days (6 Students) $600.00 2004-14/15Q FT-10 Basic & Intermediate Networks (Distributor Only) This course will cover the hardware and software of FT-10 Networks. Subjects discussed will be familiarization, installation, operation and troubleshooting of simple (Plug and Play) Networks, and the use of Lonmaker Integration Tool (trade mark Echelon Corp) to create commissioned networks. A written and hands-on qualification assessment is included. PowerGen Core Course Requirements InPower Service Software Training (2000-20Q) FT-10 Networks (PowerGen University) 5.0 Days (6 Students) $1500.00 23

2004-16Q FT-10 Advanced Networks (Distributor Only) This class is designed with the advanced PowerGen technician in mind. Course content will include InPower & LonMaker Turbo software application relating to advance networking, familiarization of IWatch devices, and advanced computer (Windows 7) techniques. The course will utilize a mix of classroom and hands-on exercises throughout, and a final written examination and a Hands-on Skill Assessment will determine technician qualification status. Technicians are required to bring a laptop computer with functional licensed copies of InPower and LonMaker Turbo software pre-installed as well as their specific serial adaptors and associated cables required for connections to network controls. Technicians attending this course must have Network Administrative privileges in order to fully communicate with network controllers during class. PowerGen Core Course Requirements InPower Service Software Training (2000-20Q) FT-10 Networks (PowerGen University) FT-10 Basic Networks Qualification Classroom (2004-14Q) FT-10 Intermediate Networks Classroom (2004-15Q) 5.0 Days (8 Students) $2250.00 2007-08Q Consumer - RV Gas Full Service Qualification This is a course on the Emerald Advantage/Marquis Gold and Microlite with the addition of vintage Emerald/Marquis, and other gasoline gensets. Overview, Installation, Periodic Maintenance and Troubleshooting will be the topics of discussion. The course includes hands-on operation and troubleshooting activities followed by a skills assessment. Completion of this course will earn the technician a Full Service Qualification for RV Gas. Mandatory Prerequisites (for Cummins PowerSouth Technicians): Repair Level Qualification for RV GAS Gensets (2007-07Q) InPower Onan on PGU (CST6029) 5.0 Days (6 Students) $1500.00 2007-10/2009-26Q Consumer - RV Diesel Full Service Qualification This is a course on the QuietDiesel (formerly known as Kubota) with the addition of the 3200 QD genset. Overview, Installation, Periodic Maintenance and Troubleshooting will be the main topics of discussion. The course includes hands-on operation and troubleshooting activities followed by a skills assessment. Completion of this course will earn the technician a Full Service Qualification for RV QuietDiesel, and the 3200 QuietDiesel. Mandatory Prerequisites (for Cummins PowerSouth Technicians): Repair Level Qualification for RV Diesel Gensets (2007-09) InPower Onan on PGU (CST6029) 5.0 Days (6 Students) $1500.00 2007-12/14Q Consumer - Marine Gas & Diesel Full Service Qualification This course will cover the Electronic QuietDiesel and Quiet Gasoline Marine Gensets, and their predecessors. Basic mechanical and electronic troubleshooting and schematic reading will be emphasized. The successful completion of this course will fill the requirements for eqd (2000-26Q Miracle) and eqg (2002-15Q Miracle Gas) qualification courses. Completion of this course will earn the technician a Full Service Qualification for Marine Gas and Diesel Full Service. Mandatory Prerequisites PGU Repair Level Qualification (see QSOL Smart Program Guide) 5.0 Days (6 students) $1500.00 24

2007-16/18/23Q Consumer Commercial Mobil Full Service Qual The technician will learn about the consumer commercial diesels, the first EFI unit in its class, and other advanced commercial features, and functionality. Students will also learn about the fully integrated hydraulic package of the CMHG. The course covers best practices for Genset operation, installation, and servicing. Completion of this course will earn the technician a Full Service Qualification for Consumer Commercial Gas, Diesel and Hydraulic Gensets. Mandatory Prerequisites PGU Repair Level Qualification (see QSOL Smart Program Guide) 5.0 Days (6 students) $1500.00 2007-21Q Consumer - ComfortGuard Installation and Maintenance This course is for ComfortGuard Installation and Maintenance, with primary focus on the APU. The HVAC unit will also be discussed along with theory and troubleshooting. A fundamental knowledge of power generation is a must for this class. Completion of this course and ALL prerequisite courses will earn the technician a Full Service Qualification status for ComfortGuard APU Mandatory Prerequisites (for Cummins PowerSouth Technicians): PowerGen Basic Electrical on PGU (CST-0584 Basic Power Generation on PGU (CST0585) Basic Mechanical on PGU (CST0586) ComfortGuard Course on PGU (CST0614) InPower Onan on PGU (CST6029) 3.0 Days (6 Students) $900.00 2008-08/13Q Industrial - PowerCommand Controls PC 1.x & 2.x Qualification PC 1.x and 2.x Training Course addressing the features and functions of the PowerCommand 1302 and 2300 control modules and the HMI Display used with each control. Course prepares technicians to understand the operation, installation, and communication systems of this control board and HMI. FAE and Hydro-mechanical applications are covered. This is the in-class portion of the PowerCommand 1.x & 2.X. This is required to become Full Service qualified on these controls. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. Mandatory Prerequisites (for Cummins PowerSouth Technicians): InPower Software (classroom) CORE Course Program PowerCommand 1.x Familiarization on PGU (CMT6103) PowerCommand 2.x Familiarization on PGU (CMT6035) 5.0 Days (6 Students) $1500.00 2008-18/19Q Industrial - PowerCommand Control PC 3.3 Qualification Training Course includes classroom and simulator training covering basic FAE application control installation and operation. This course covers basic paralleling features including standalone, synchronize only, and isolated bus applications. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. Mandatory Prerequisites (for Cummins PowerSouth Technicians): InPower Software (classroom) CORE Course Program PowerCommand 2.x Series Full Service Qualification 5.0 Days (6 Students) $1500.00 25

2009-20Q Consumer - RS Liquid Cooled Genset Qualification Residential Standby Instructor Led 4.5 days classroom assessment course, which Include Transfer Switch (RSZ, RST, RSS, and OTEC) and Fuel Systems - NSPS, Controls: 1301 and Control 1302 Mandatory Prerequisites (for Cummins PowerSouth Technicians): PGU Courses 586, 6007, 116, 117, 134, 135, 6097, 6098, 6103, & 6099 5.0 Days (6 Students) $1500.00 2009-23Q Consumer - RS Air Cooled Genset Qualification This course is designed to familiarize the technician with the generator, transfer switch, controls and web-based communication capability of the complete Home Stand-By RS12,000kW genset package. Theory and hands-on qualification testing is included. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. Mandatory Prerequisites (for Cummins PowerSouth Technicians): PGU Courses 586, 6007, 116, 117, 134, 135,6032, 6029, 6103, & 6099 3.0 Days (6 students) $900.00 2009-28Q Consumer - RV Hybrid QuietDiesel Qualification This course on the Hybrid QuietDiesel offers the technician an overview of the installation, periodic maintenance and troubleshooting procedures. Included in this course are discussions on the power unit, automatic transfer switch, inverter and the control display. The course is compiled of classroom instruction and hands-on activities followed by a skills assessment. Successful completion of this course will provide the technician with Full Service Qualified status on the Hybrid QuietDiesel Genset. Mandatory Prerequisites (for Cummins PowerSouth Technicians): Repair Level Qualification status for Hybrid QuietDiesel Genset InPower Onan PGU training or InPower Onan Classroom course (6029) 5.0 Days (6 students) $1500.00 2009-42Q Consumer - 20kW CMSD Full Service Qualification This course will cover the 20kW Commercial Mobile genset. The course details on Installation, Operation, Control, Fuel System, YD Alternator, Engine, and Troubleshooting. Mandatory Prerequisites (for Cummins PowerSouth Technicians): Repair Level Certification for Commercial Mobile 20kW CMSD (2009-41Q) InPower or InPower Onan Software on PGU (CST6029) 2.0 Days (6 Students) $600.00 2009-43Q EPA Emissions Performance Standards (NSPS) Qualification New Source Performance Standards (NSPS) are new emission standards set forth by the EPA as it pertains to gaseous fueled generator sets. This training will cover Basic Gas Principles, System Layouts, Components, Troubleshooting, Service Tools, and EPA basics as it pertains to NSPS. Mandatory Prerequisites (for Cummins PowerSouth Technicians): InPower Software (classroom) CORE Course Program 2.0 Days (6 Students) $800.00 26

2010-03Q PSI Gas Genset Engine Qualification (Distributor Only) With continued advancements in gaseous fueled genset technology, technicians are challenged with maintaining a complete knowledge base of the entire power package (engine & generator). This course is designed to provide the technician with the knowledge of the Power Solutions, Inc. engine (GM Based), so that they may make more informed decisions relative to warranty repairs/replacements. This course includes the complete disassembly and reassembly of a 3.0L inline 4 cylinder and a 5.7L V8 engine. Mandatory Prerequisites PowerGen Core Course Requirements 3.0 Days (6 students) $1050.00 2011-08Q Industrial BTPC 1600-3000 Amp ATS (GEZ Bypass) This course is designed to enable technicians in performance of service and repairs on the high amp (G. E. Zenith ) horizontal bypass transfer switch with PowerCommand controls. Lessons will include the automatic and bypass switch mechanisms. Hands-On exercises will focus on internal cabinet layout, automatic and manual control of the ATS, racking out the automatic switch and troubleshooting common fault situations Note: Each student MUST bring a laptop computer with InPower software installed and his/her Calibrated CAT IV meter, PPE equipment and proof of formal electrical safety training OTPC Transfer Switch (classroom) CORE Course Program BTPC Assessment on CLC (CMT0692-EN-TST) 2.0 Days (6 Students) $800.00 2011-25Q DMC 1500 Paralleling Switchgear This class is intended for the Experienced and Advanced generator and switchgear technician. The lab practical validates the student s ability to effectively troubleshoot and repair the Digital Master Control 1500. The lesson is backed up with more than 50% hands-on exercises, and procedures. Mandatory Software Requirements (must be downloaded, and installed prior to class): RSLOGIX MICRO version 8.30 RSLINX CLASSIC version 2.57.00(CPR 9 SR3) Core Course Requirements 5.0 Days (8 Students) $1750.00 2012-44Q EPA Tier IV Qualification This course is designed to qualify technicians on the NEW EPA tier 4 (Intérim and final) solution for the High Horsepower exhaust aftertreatment requirements. NOTE: The communication software for the simulator (Luis Gen2) must be downloaded and installed from the software shelf prior to attending this class. 3.0 Days (6 Students) $1050.00 2013-XXQ Engine Fundamentals This course is to qualify the technician in the Fundamentals of Engines, Gasoline, Diesel, and Gaseous Fueled engines. This course will be a prerequisite for most genset controls classes. 5.0 Days (6 Students) $1500.00 27

2013-XXQ Generator Fundamentals This course is to qualify the technician in the Fundamentals of A/C Alternators. Electrical theory, and general design of Alternators. This course will be a prerequisite for most genset control classes. 5.0 Days (6 Students) $1500.00 2013-XXQ Transfer Switch Fundamentals This course is to qualify the technician in the fundamentals of Automatic Transfer Switches, with emphasis on the switch mechanisms. This course will be a prerequisite for most transfer switch control classes 5.0 Days (6 Students) $1500.00 2013-XXQ Fundamentals of AC Generators 5.0 Days (6 Students) $1500.00 C-177 Industrial - Fundamentals of Power Generation This course is designed for technicians with little or no knowledge of electricity or how generators work. This course will give them a fundamental understanding of Onan Industrial/Commercial generator sets and transfer switches. In addition to an understanding of electrical fundamentals and basic schematic reading, this training will introduce technicians to installing, operating and troubleshooting standby power systems. Each participant is required to bring his/her Calibrated CAT IV Meter, PPE, and Proof of formal Electrical Safety training. Mandatory Prerequisites (for Cummins PowerSouth Technicians): Basic Electronics Theory & Troubleshooting CVC (B/N No. 3898967) Fundamentals of Power Generation Assessment on PGU (CMT0117) 5.0 Days (6 students) $1500.00 C-500 Insite for PowerGen Technicians This class is intended for the commercial distributor technician needing extended communication capability beyond that provided by the InPower Pro Service Software. Classroom instruction and hands-on activities will revolve around Core II ECS communication procedures, Witness Testing and calibration download exercises for FAE driven generators. Attending technicians must bring a laptop computer equipped with fully functioning Insite and InPower (Pro or Lite) software, an INLINE 4/5 adapter kit and necessary connection cables. Mandatory Prerequisites PowerGen Core Course Requirements Insite 7.X CVC (B/N4091839) InPower Service Software Classroom (2000-20Q) 2.0 Days (6 students) $600.00 C-501 New ATS Product Introduction for 2011 This course will be an introduction to the new automatic transfer switch products scheduled for release in 2011. Complete information on these products was not available at the time this document was completed. 1.0 Days (6 students) $300.00 C-502 OT-III ATS Controls (Vintage Switchgear) This course is designed with new powergen technicians in mind. It is intended to assist new powergen technicians with vintage OT-III style transfer switches and the associated accessories used with this product line. Lessons will include the Power Sentry Control and the GE style linear motor contactor. A good mix of classroom lecture and hands-on activities create a successful learning experience. 2.0 Days (6 students) $600.00 28

C504 Aftermarket Conversions Upgrade This one day course outlines the procedure for upgrading the PCC-3100 genset control to PCC-3.3 Hydro-mechanical controls. Lessons will include the replacement A-40 box, component location, the replacement door with the HMI- 320, extraction of data from the EEPROM of the PCC-3100 control and the use of the Excel(r) spreadsheet to convert these current adjustments to acceptable parameters for the 3.3 control. 1.0 Days (6 Students) 400.00 C-6029 InPower Onan Service Software This course is designed to take the novice technician through the use of a PC to communicate with "Consumer Product" generators. Various exercises will be utilized to familiarize technicians with troubleshooting and test/reports made available through the InPower Onan program. Technicians are required to bring to class a laptop with InPower Onan software already installed, and the necessary cables needed for connecting to the generator. 1.0 Day (6 students) $300.00 Consumer Product Skills Qualification The courses listed below are one day HANDS-ON SKILLS ASSESSMENTS for a variety of consumer products. Each course is a qualification session in itself and consists of only ONE product category per course. A technician who is seeking Full Service status on any consumer product must complete ALL of that products required course categories and may choose to complete them one at a time over a period of days or all in one day (each course session costs $250.00). NOTE: A technician MUST be Repair Level Qualified in the product for which he/she is wishing to achieve Full Service status. Repair Level Qualified in Product NOTE: A technician may qualify for only one category per session MAX 4 sessions per day. Course Number Course Description 588 RV & Consumer Commercial Gas Skill Assessment 589 RV & Consumer Commercial Diesel Skill Assessment 6004 Marine Belt Drive Gas Skills Assessment 6005 Marine Belt Drive Diesel Skills Assessment 6006 Marine Direct Drive Diesel (MDD) Skills Assessment 6015 ComfortGuard Skills Assessment 6017 Marine Direct Drive Diesel (MDK) Skills Assessment 6019 RV Hybrid Quiet Diesel Skill Assessment 6028 Consumer Commercial Hydraulic/PTO Skills Assessment 6031 RV 3200 Quiet Diesel Skill Assessment 6033 RS Air Cooled Skills Assessment 6100 RS Liquid Cooled Skills Assessment 6110 Commercial Mobile 20kW CMSD Skills Assessment 1.0 Day (4 Sessions) $300.00 Classes designated as INDUSTRIAL may have attendance restrictions. Call Tami Bell at (813) 635-5701 for further information. 29

Cummins Learning Center Cummins Power Generation and Cummins Power South, LLC are now making it possible for distributor and dealer technicians to obtain some of their required courses and qualifications for CPG Product Qualification, on the Cummins Learning Center WEB Site. For enrollment information, contact Cummins Power South, LLC at (813) 635-5701. Notes 30

Lodging Information Note: Attendees must make their own arrangements for hotel accommodations. Be sure to mention that you are receiving training at the Cummins Technical Training Center to get published rates listed below. Listed rates do not include applicable local/state/lodging tax. Tampa Area Hotels: Hilton Garden Inn Tampa Southeast (813) 626-6610 4328 Garden View Dr. Riverview, FL 33578 This hotel opened in January 2009 and is close to Westfield Mall and many restaurants. All rooms are equipped with mini-refrigerator, microwave and coffee maker. There is an on-site restaurant and lounge, a fitness center, outdoor pool and laundry. Includes free parking, high speed internet and cooked to order breakfast. 2013 Rate - $94/Night Holiday Inn Express (813) 910-7171 8310 Galbraith Rd. Tampa, FL 33647 New hotel offering wireless internet, breakfast and a ice cream social every evening. 2013 Rate - $97/Night Atlanta Area Hotels: Holiday Inn Atlanta Airport South (404) 763-8800 4669 Airport Blvd., College Park - GA 30337 Hotel is newly remodeled. Complimentary wireless internet, fridge and coffee maker in each room. Hotel has indoor heated pool, exercise room and restaurant. King or Double/double 2013 Rate - $89/Night Hyatt Place Atlanta Airport South (770) 994-2997 1899 Sullivan Rd, College Park - GA 30337 Hyatt Place is a new kind of hotel that puts style, innovation and The Hyatt Touch within everyone's reach. Guests will enjoy a spacious guestroom with a 42" flat panel high-definition television, signature Hyatt Grand Bed, a plush Cozy Corner oversized sofa sleeper that is separated from the sleeping area, and complimentary high-speed Wi-Fi Internet access throughout the hotel. 2013 Rate - $105/Night Sheraton Gateway Atlanta Airport (770) 997-1100 1900 Sullivan Rd, Atlanta - GA 30337 Guest rooms offer the comfort of the renowned Sheraton Sweet Sleeper(SM) Bed, 32-inch LCD flat screen televisions, ergonomic desk chairs, as well as new lighting throughout every room. High Speed Internet Access (charge) keeps you connected. A full service restaurant is located in the hotel. 2013 Rate - $101/Night 31

Training Center Technical Service Center - Tampa, FL 5903-A Hampton Oaks Pkwy Tampa, FL 33610 (813) 635-5701 32

Training Center Training Center - Atlanta, GA 5125 Highway 85 Atlanta, GA 30349 (813) 635-5701 33

Please Print PROGRAM NAME REGISTRATION APPLICATION FORM PROGRAM NUMBER PROGRAM DATE DAYS COST FIRST NAME MI LAST COMPANY CONTACT ADDRESS CITY ST ZIP COUNTRY PHONE FAX VIRTUAL COLLEGE ID NUMBER ACCOUNT NUMBER P.O. NUMBER NOTES Classes begin promptly at 8:00 am daily. We suggest that students wear comfortable clothing suitable for working on engines (NO SHORTS or SANDALS). Payment is due upon the first day of class if not prepaid. Cancellations MUST be received no later than two days (48 hours) prior to the scheduled program or you will incur full tuition billing. In addition, students are responsible for making their own hotel reservations. A list of hotels with reduced rates is provided for your convenience. Technical Service Centers 5903-A Hampton Oaks Parkway - Tampa, Florida 33610 - Phone 813-635-5701 - Fax 813-623-5442 5125 Highway 85 - Atlanta, GA 30349 - Phone 813-635-5701-813-623-5442 34

35

36