AT-S63 Version 3.2.1 Patch 5 Management Software for the AT-9400 Basic Layer 3 Gigabit Ethernet Switches Software Release Notes Please read this document before you begin to use the management software. Included in this document are the following: Supported Platforms on page 2 Product Documentation on page 3 Switch Models and Management Software on page 3 Version 3.2.1 Patch 5 Resolved Issues on page 4 Version 3.2.1 Patch 5 Known Issues on page 4 Contacting Allied Telesis on page 5 Obtaining Management Software Updates on page 5 PN 613-001077 Rev A 1 Allied Telesis, Inc.
Supported Platforms AT-S63 Version 3.2.1 Management Software is supported on the following AT-9400 Gigabit Ethernet Switches: Basic Layer 3 Models AT-9424T (AC) AT-9424T/POE (AC) AT-9424Ts (AC) AT-9424Ts/XP (AC) AT-9448T/SP (AC) AT-9448Ts/XP (AC) Note: AT-9400 Basic Layer 3 Switches that have Version 2.1.0 or earlier of the AT-S63 Management Software have to be upgraded to Version 2.2.0 before you can install Version 3.2.1. For the Internet locations of the management software for Allied Telesis products, refer to Obtaining Management Software Updates on page 5. This version is not supported on the following AT-9400 Switches: Layer 2+ Models AT-9408LC/SP (AC) AT-9424T/GB (AC) AT-9424T/SP (AC) AT-9424T/GB-80 (DC) AT-9424T/SP-80 (DC) For information on the availability of future releases of the management software for the Layer 2+ switches, contact your Allied Telesis sales representative. This release supports the following redundant power supply on the AC models: AT-RPS3204 For a list of supported GBIC, SFP, and XFP modules, contact your Allied Telesis sales representative. Caution: The software described in the documentation contains certain cryptographic functionality and its export is restricted by U.S. law. As of this writing, it has been submitted for review as a retail encryption item in accordance with the Export Administration Regulations, 15 C.F.R. Part 730-772, promulgated by the U.S. Department of Commerce, and conditionally may be exported in accordance with the pertinent terms of License Exception ENC (described in 15 C.F.R. Part 740.17). In no case may it be exported to Cuba, Iran, Iraq, Libya, North Korea, Sudan, or Syria. If you wish to transfer this software outside the United States or Canada, please contact your local Allied Telesis sales representative for current information on this product s export status. PN 613-001077 Rev A 2 Allied Telesis, Inc.
Product Documentation Refer to the Allied Telesis web site at www.alliedtelesis.com for the latest installation and user guides. Switch Models and Management Software The following table lists the versions of the AT-S63 Management Software that initially supported the different models in the AT-9400 Series. If you want to load an older version of the management software onto a switch, you should refer to the table to determine whether the version supports the switch. For example, support for the AT-9424Ts Switch was introduced in version 2.1.1. Attempting to load an earlier version of the software on that model will be unsuccessful. Model AT-S63 Management Software Version AT-9424T/GB 1.0.0 AT-9424T/SP 1.0.0 AT-9408LC/SP 1.1.0 AT-9448Ts/XP 1.3.0 AT-9448T/SP 2.0.0 AT-9424Ts/XP 2.0.0 AT-9424Ts 2.1.1 AT-9424T 3.1.0 AT-9424T/POE 3.2.0 PN 613-001077 Rev A 3 Allied Telesis, Inc.
Version 3.2.1 Patch 5 Resolved Issues The following issues have been resolved in Version 3.2.1 Patch 5 of the AT-S63 firmware: LACP - There must be more than 2 active links in an LACP group. Single Links do not send out LACPDUs. This issue applies to both the stacking and standalone configurations. Routing Link Aggregation - When a static and/or default route is configured on the stack and the connection to that route is on a LACP or Static Aggregation group, the switch cannot communicate through that link. This issue applied to a stacking configuration only. VLAN Tagging and Stacking - When a port on the master is configured as Tagged for a VLAN that is untagged on a member switch, ARP Replies from that interface no longer egress corresponding member ports. This issue applied to a stacking configuration only. (# 6605) ARP Requests on Tagged Ports of Member Switches - Tagged Member ports do not reply to ARP Requests. If you tag a member port, ARP requests that are received are processed (can be displayed in ARP table), but replies are never sent out. This issue applied to a stacking configuration only. (#6606) CPU Generated ARP Replies on SFP Ports - CPU generated ARP replies always egress the switch as untagged on XFP Ports even when the ARP Request comes in as tagged. (#6614) ARP Replies Do Not Egress as Tagged on Tagged Ports - On the AT-9448TS-XP (only) CPU ARP replies for ports 13+ do not egress as tagged for VID1. (#6497) Modifying VLANs Through Web GUI - Switch management hangs when modifying VLANs through the Web GUI. (#6747) ARPs Never Aged Out - ARP Timer does not work. ARP Table never ages out addresses. (#5035) Character Limitation in VLAN Port Field - Cannot create VLANs with more than 79 characters in the port field. (#6711) Member Connected External Routes - When a static and/or default route is configured on the stack and the connection to that route is not on the master, the switch cannot communicate through that link. This issue applied to a stacking configuration only. (#6362) SNMPv3 Memory Leak - SNMPv3 Memory Leak when performing an SNMP Walk. (#6416) Version 3.2.1 Patch 5 Known Issues Default Route and Management - If a default route (add ip route 0.0.0.0) is configured, you will not be able to manage, ping, or have any IP connectivity with the switch CPU unless you are connected to a link directly off of the master. This issue is only with the default route and does not affect individual static routes or routed traffic. Slow Management Response with Large Stack - The more switches in the stack, the slower the cpu will respond to management packets when not directly connected to the master. This only affects IP management and does not affect switching protocols, L2 switched or L3 routed traffic. PN 613-001077 Rev A 4 Allied Telesis, Inc.
Contacting Allied Telesis This section provides Allied Telesis contact information for technical support and for sales and corporate information. Online Support You can request technical support online from the Allied Telesis Knowledge Base at www.alliedtelesis.com/support/kb.aspx. You can submit questions to our technical support staff from the Knowledge Base and review answers to previously asked questions. Email and Telephone Support For Technical Support via email or telephone, refer to the Allied Telesis web site at www.alliedtelesis.com. Select your country from the list on the web site and then select the appropriate tab. Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesis without an RMA number will be returned to the sender at the sender s expense. To obtain an RMA number, contact the Allied Telesis Technical Support group at www.alliedtelesis.com/support/rma.aspx. Sales or Corporate Information You can contact Allied Telesis for sales or corporate information at our web site at www.alliedtelesis.com. Obtaining Management Software Updates New releases of management software for our managed products are available from the following Internet sites: Allied Telesis web site: www.alliedtelesis.com Allied Telesis FTP server: ftp://ftp.alliedtelesis.com If the FTP server prompts you to log on, enter anonymous as the user name and your email address as the password. Copyright 2008 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis is a trademark of Allied Telesis, Inc. Microsoft and Internet Explorer are registered trademarks of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape Communications Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages. PN 613-001077 Rev A 5 Allied Telesis, Inc.