RING JOINT SYSTEMS 07
08 Table of Contents Model R-88 Pages 10-11 Model R-88 Large Diameter Page 1 Model RH-1000 1000 PSI Coupling Page 13 Model RX-3000 3000 PSI Coupling Page 1 Model RX-3770 3770 PSI Coupling Page 15 RJ-10 90 Elbow Page RJ-11 5 Elbow Page 17 RJ-0 Tee Page 17 RJ-1 Reducing Tee Page 18 RJ-50 Concentric Reducer Page 19 RJ-51 Eccentric Reducer Page 19 RJ-60 5 Cap Page 0 RJ-70 Flange Adapter Page 0 * Shurjoint product specifications can be found at www.shurjoint.com GRINNELL reserves the right to change the contents without notice. COUPLING MATERIAL SPECIFICATIONS Housing: to ASTM A 395, Gr. 65-5-15, min. tensile strength 81 Bar (65,000 psi). Sizes 00 to 650 (8" to 6 ) consist of two housing segments 700 to 950 (8" to 38 ) consist of six housing segments 1000 to 00 (0" to 96 ) consist of eight housing segments Surface Finish: colours Weld s: Rubber Gasket: (Colour code: Green stripe) Good for cold & hot water up to 110 C (30 F). Also good for services for water with acid, water with chlorine, deionized water, seawater and waste water, dilute acids, oil-free air and many chemicals. Not recoended for petroleum oils, minerals oils, solvents and aromatic hydrocarbons. Maximum Temperature Range: -3 C to 110 C (-30 F to 30 F)*. *EPDM gaskets for water services are not recoended for steam services unless couplings or components are accessible for frequent gasket replacement. (Colour code: Orange stripe) Recoended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Also good for water services under 66 C (150 F). Temperature range: -9 C to 8 C (-0 F to 180 F). Do not use for HOT WATER above 66 C (150 F) or HOT DRY AIR above 60 C (10 F). Butyl. For additional details contact a GRINNELL Sales Bolts & Nuts: 3 " to 1 ): Heat treated carbon steel track bolts to ASTM A 183 Gr., minimum tensile strength 758 Bar (110,000 psi), Zinc electroplated, with heavy-duty hexagonal nuts to ASTM A563. 1 1 " to 1 1 ") sizes: Carbon steel hex. bolts to ASTM A 307 Gr. A or B, minimum strength 136 Bar (60,000 psi), Zinc electroplated, with hexagonal nuts to ASTM A 563. Bronze nut are available upon request. www.grinnell.com
), ( Maximum Internal Service Pressures of Carbon Steel Pipe ASTM A53 Gr. B. Nominal ). )*(+ ),,+ --- LW XS STD 0.5" / Size 0.5" 0.375"* 0.31"^ )1 ),*( ).+. /+. -(( /)0 Bar Bar -)- *.. 1-* +.) Bar psi psi psi 00 109. 69. 53.6 50 87.0 63.0.8 300., )+ )( (0/ -11 *** +.* 0+( 1)* 7.9 5.3 36.0 350 66.3 9. 3.8 00.+ ++( 1// 00) 57.8 3.1 8.6.(.1 *** 1)*.-* 50 51.3 38.3 5. 0, *). 0(. 0)( 6.1 3..8 0. 1-* 0**./* 600 38.3 8.6 19.0 650 0+ 110 00).-* 35.3 6.3 1.9 0( 1)* 0),.*( 700 3.8.5 0.3 750 1, 0+( 01/.+).-*../.)- 30.5.8 19.0 800 8.6 1. 17.8 900 11 00).1(.,+ 5. 19.0 15.8 1( 950.1 18.0 15.0 1000 *. 0,)..*.8 17.1 1. *1.-*.,+ 1050 1.7.3 1.9 *+.*1 )/, 100 +,.1* )(0 19.0 1. 1300 ++.,,.0+.., )+* 17.5 13.1 )*, )-- 1350.9 1.6 100.3 1. 1 (1 +( -. )(0 )/1 15. )*- )0- )1* 11. ))( 50 13.8 10.3 1700 13. 10.0 1800 1.6 9. 100 10.8 8.1 00 9. 7.1 1. 0)*.0+ )(- 1100 0.8 15.5 /+ )0- ),0 Except * 00 (8"): 8. (0.3"); 50 to 600 (10" to "): 6. (0.5"); 650 to 1050 (6" to "): 7.9 (0.31") Refer to back cover for country-specific contact information Specifications Shurjoint Tech Data Sheet: O-01 Coupling The ring joint coupling provides a much more secure joint than a comparable roll-grooved system, simply because the contact area of the rings is much greater than that of the roll-groove profile. In addition, the welded rings are # $ %&' able to withstand - 3 times the shearing forces of roll grooves. High pressure couplings up to 60 Bar (3770 psi) are available.!" Max. Internal Service Pressures of Carbon Steel Pipe ASTM A53 Gr. B When designing a piping system you must select pipe with the appropriate wall thickness to correspond with the intended working pressure of the system. The table lists design working pressure by the pipe wall schedule, XS, STD and LW, of representative ASTM A53 Gr. B carbon steel pipe calculated in accordance with the formula stipulated in ASME B31.1 Power Piping 10.1. Where: SE (tm-a) P = Do - y (tm - A) P = Maximum internal service pressure (psi) SE = Allowable stress (psi) (ASTM A53 Gr. B = 103 Bar (15,000 psi) tm = Minimum pipe wall thickness (inch) (87.5% of nominal wall thickness) Do = Outside diameter of pipe (inch) y = A coefficient (For ferritic steels 3 C (600 F) or below = 0.) A = Additional thickness (inch) (A = 0) General notes: Additional information is included in our data sheets and is available upon request. It is the Designer s responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation constructions. Never remove any piping components nor correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified with the gasket recoendation listing for the specific application. 09
Shurjoint Model R-88 Couplings (Page 1 of 3) Shurjoint Tech Data Sheet: O-01 The Shurjoint Model R-88 Coupling is an ideal pipe joining method when pipe is difficult to groove or when grooving is not the preferred joining method. Available in sizes 00 thru 00 (8 to 96 ) the R-88 offers ease of use and excellent performance. The Model R-88 Coupling is supplied with a pair of factory supplied weld rings. For installation weld a factory-supplied weld ring on each pipe end to be connected, next mount the rubber gasket over the pipe ends, place coupling segments over the gasket and fasten the bolts and nuts. The R-88 Coupling is considered a shoulder coupling with the factory supplied weld rings serving as the joint shoulders. The R-88 s performance standards meet and or exceed the requirements of ASTM F176 and AWWA C606. The factory supplied weld rings offer a much more economical and convenient alternative to traditional shoulder rings, such as Type A, B, C, D, E, and G rings. The R-88 Coupling can also be used on stainless steel pipe with optional weld rings available in compatible stainless steel grades. Check with GRINNELL for details and availability. The Model R-88 Coupling is available in sizes from 00 (8 ). Sizes 350 to 650 (1 to 6 ) are now available either in a two-segment style (R-88N) or multi-segment style (R-88). The two-segment style offers a easier and faster installation. Sizes 700 to 00 (8 to 96"). The larger diameter couplings are comprised of 6 to 8 housing segments depending on the size and feature two bolts at each joint segment to ensure a positive connection. Typical applications (3.1 Pressure-Temperature Rating Size.+ 0,,567),,89 0,,567),,89 Nom. Working Pressure Rating (STD) EPDM: 00-600 Class 0 Bar @38 C 50 EPDM: 0(3/+.(D0+ 0,,567),,89 650 Class )-*567),,89 0 Bar @38 C 150 EPDM: 700-900 Class 0 Bar @38 C 150 EPDM: 950-00 Class 1 Bar @38 C 15 :;<=>.0,89 :;<=>.0,89?6@A6BC>)(,89 Max. Service Temperature :;<=>.0,89?6@A6BC>)(,89 110 C Nitrile: 8 C :;<=>.0,89?6@A6BC>)(,89 110 C?6@A6BC>)(,89 Nitrile: 8 C 110 C Nitrile: 8 C 110 C Nitrile: 8 C 10 A 700 (8") R-88 coupling installed in a chill water system GRINNELL reserves the right to change the contents without notice. *Working pressure is based on standard wall carbon steel pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 3 times the working pressure for sizes up to 300 (1") and times for sizes 00 (1") & above. www.grinnell.com
M R RING JOINT SYSTEMS Shurjoint Model R-88 Couplings (Page of 3) Shurjoint Tech Data Sheet: O-01 MN O N O V WPQPRSTUT 600-650 (" - 6") 00 - (8" - 0") (R-88N) (R-88 & R-88N) (), Max. Working Pressure s both sides fully Dimensions Bolt Size Sealing Separation welded Surface Size E ). (E+.* ),E,()0E,,0E)) )+E( XS STD LW L R (max) Nominal O.D. A B C (. ) (.375 ) (.31 ) No. )1 )1E,,, ),E-*, ).E-*, +,, Bar 1,, Bar ).E./)*E.,0E.* Bar )*E/0)/E1,0E+* )1E-. )-E/,0E0/,E/) psi psi psi 00 19.1 0 8 8 56 330 79 3 F G..E. x 3 3 6.8 7.6 50 73.0 0 8 8 31 386 83 3,E)/ 0,E( 0(E0 x 3 3 6.8 10.1 300., )+ )( )+E,,, )(E,,, 0*,.,E0-.1E)-1E.0 )-E/..)E*.0E+* 33.9 0 8 8 37 55 86 7 )E,. H FI,E.* *,E( 1)E) 8 x 6 1 6 8.8 1.0 350 (R-88N) 355.6 0 8 05 93 93 7 8 x 5 1 6 8 6. 17. 00 (R-88N).+.1.+E,,,.,E,,,.1E,,, *,, 06. 1,, 35 0,, 1,, 0,, 8.*,./E*(0.E-(+E+/..E1+.*E//1E0*.-E)-0,E,1E(1 55 57 93 7 8 x 5 1 6 8 6. 18.7.E,, )E)( J K F L,E0-* ),/E0 (1E, )-0E* 50 (R-88N) 57. 35 8 517 61 107 1 x 5 1 30 8 9.5 3.1 (R-88N) 508.0 35 8 0 570 660 110 1 x 5 1 30 9.5 9.5 38. 600 (R-88N) 609.6 35 8 17 690 76 13 7 8 x 6 1 30 1.7 9.5 9.7 650 (R-88N) 660. 8 0 17 751 85 170 1 x 8 7 8 50 1.7 9.5 78.7 R-88N is a two-segment type coupling. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page 09 for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Refer to back cover for country-specific contact information 11
R RING JOINT SYSTEMS V W Shurjoint Model R-88 Couplings MN PQPRSTUT O N O Large Diameter M (Page 3 of 3) Shurjoint Tech Data Sheet: O-01.( R-88.(E,,, Size: 100 (8") 700-950 (8" - 38") 1000-00 (0" - 96") 0, 0,E,,, 00E-* 0)E-* 0*E*, 0-E+,...E..)(E/ Max. Working Pressure Dimensions Bolt Size s both sides fully welded Sealing Separation XS STD LW Surface L Size R E (max) Nominal O.D. A B C (.") (.375") (.31") No. Bar Bar Bar 0+ 0. 0.E,,, 1,,.*, 0*E-* 0/E*, psi psi psi 700 711. 8 0 17 806 90 171 7..*E1 8 x 50 1.7 1.7 101.0 1 0( 01 01E,,, 0-E-* 1)E*,.*0E, 750 76.0 8 0 17 857 955 171 1 x 3 1 50 1.7 1.7 99.5 1 1, 0+E,,, 0(E,,, 1,E,,, 0*, 0,,.,, 11E+/1(E0/ 0/E-* 1)E-* 10E*, 1*E*, +E-0.E,, F L,E*,.1+E,.-*E, 0),E. 800 81.8 8 0 17 908 1003 171 1 x 3 1 50 1.7 1.7 10. 1 850 863. 0 1 959 105 171 1 x 3 1 50 1.7 1.7 115.0 1 900 91. 0 1 1010 1103 171 1 x 3 1 50 1.7 1.7 111.6 1 1( 1. 11 1.E,,, 1+E-,*,E0/ 0.+E/ 950 965. 0 1 1060 1156 171 1 x 3 1 50 1.7 1.7 15.0 1 *. 11E,,, )-* 1(E++*)E(/ 010E. 1000 10.0 0 1 1135 19 198 1 x 3 1 60 15.9 15.9 11.0 *1 1(E,,, 0,,.0. *.E+( **E/)-E(, 1++E- 1050 1066.8 0 1 1186 180 198 1¼ x 5 60 15.9 15.9 18.6 *+ *.E,,, +)E.* +,E+, 1*0E. 1100 1117.6 0 1 136 1318 198 1¼ x 5 60 15.9 15.9 156.0 +, *1E,,, +0E.* +.E+, 1-.E) 100 119. 0 --- 1338 10 198 1 x 3 1 60 15.9 15.9 11.8 ++ *+E,,, ++E,,, +,E,,,.0. )-* +*E0( +/E0( -+E,, +(E+, +1E+, -*E-/(E,, -E(, H K,E+.* 1((E. *0-E. +).E* 1300 130.8 1 --- 1555 1539 198 1¼ x 5 60 15.9 15.9 06.0 1350 1371.6 1 --- 60 1590 198 1¼ x 5 60 15.9 15.9 1.6 100 1. 1 --- 60 1 198 1¼ x 5 60 15.9 15.9.0 (1 +( +(E,,, )-* -(E*, --E-/(E,, -(*E1 1 15.0 1 --- 176 17 198 1¼ x 5 60 15.9 15.9. /+ -. (1E,,, /+E,,, -.E,,, ).* )*, ),, ).* DDD DDD (.E*,()E()(E,, ),+E-*),*E-/(E,, /1E-* /0E()(E,,.E0-.E0- J G J G,E-* (.0E. -(,E0-0-E- 50 76. 1 8.6 --- 193 195 1 1 x 5 60 19.1 19.1 78. 1700 177. 1 8.6 --- 199 1976 1 1 x 5 60 19.1 19.1 357.0 1800 188.8 10 8.6 --- 095 078 1 1 x 5 60 19.1 19.1 335.3 100 133.6 8.6 7 --- 06 383 1 1 x 5 60 19.1 19.1 35.7 00 38. 8.6 7 --- 711 66 1 1 x 5 60 19.1 19.1 37. For information on alternative sizes, contact a GRINNELL Sales Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page 09 for specifications For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales 1 GRINNELL reserves the right to change the contents without notice. www.grinnell.com
Y X Z R RING JOINT SYSTEMS Shurjoint Model RH-1000 1000 PSI Couplings Shurjoint Tech Data Sheet: O-06 The Shurjoint Model RH-1000 coupling is a high pressure ring joint coupling for use with Sch. 0, Sch. 80 and heavier wall carbon steel pipe. The coupling is comprised of two ductile iron heavy-wall housings, rubber gasket (EPDM or Nitrile) and two heattreated track bolts and nuts which provide a fully restrained joint and a maximum working pressure of 70 Bar (1,000 psi) depending on the pipe used. Two steel weld rings are factory supplied with the coupling. ),,,567),,89 :;<=>.0,89?6@A6BC>)(,89 Pressure-Temperature Rating Nom. Working Pressure Max. Service Rating (STD) Temperature EPDM: 110 C Class 70 Bar @38 C 00 Nitrile: 8 C *Working pressure is based on standard wall carbon steel pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 3 times the working pressure. V WPQPRSTUT ), ). ( (E+.* ),E-*, ).E-*, ),,, ),,, )+E00 )0E0. ))E),.,E,- )+E/0 )1E+* 1E.* 0E(+ 1E)-,E1- ),E)0 0/E( *-E. -.E+ Nominal O.D. Max. Working Pressure Bar psi A Dimensions B C 00 19.1 70 8 37 98 50 73.0 70 30 30 108 300 33.9 70 15 510 106 No. Bolt / Nut Size in 1" x 10 1" x 5 1" x 5 Deflection ( ) 0 18' 0 38' 0 3' R Pipe-end Preparation L E (max) 1 5 3. 18.1 1 5 3. 6.0 1 5 3. 33.0 *Bolt & nuts are UNC threaded. For information on alternative sizes, contact a GRINNELL Sales Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page 09 for specifications For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Refer to back cover for country-specific contact information 13
M R RING JOINT SYSTEMS Shurjoint Model RX-3000 3000 PSI Couplings Shurjoint Tech Data Sheet: O-05 The Shurjoint Model RX-3000 coupling is a high pressure ring joint coupling for use with Sch. 80, 10 and heavier wall carbon steel pipe. The coupling is comprised of two ductile iron heavy-wall housings, rubber gasket (EPDM or Nitrile) and two or four heat-treated track bolts and nuts which provide a fully restrained joint and a maximum working pressure up to 10 Bar (3,000 psi) depending on the pipe used. Two steel weld rings are factory supplied with the coupling. 0,,,567),,89 :;<=>.0,89?6@A6BC>)(,89 Pressure-Temperature Rating Nom. Working Pressure Max. Service Rating (STD) Temperature N O EPDM: 110 C Class 10 Bar @38 C 1 Nitrile: 8 C *Working pressure is based on API 5L X65 line pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum V times the Wworking pressure. PQPRSTUT (), ). (E+.* ),E-1( ).E-*. ))E() )*E*) *E(0,E1-.D,E*,, -(E/. Max.Working 0,,, )1E/+ )(E* Dimensions..E1( )(E/0 *E/( +E() Bolt / Nut*,E+.*D,E+./ Pipe-end Preparation )E.. F K.).E.- ))+E0+ Nominal O.D. Pressure A B C R L E Bar Size Qty. psi in 00 19.1 10 300 39 18 1 1 8 x 130 1.0-1.7 31 3 35.87 50 73.0 10 380 81 15 1¼ x 5 15.9 -.0 31 3 5.78 300 33.9 10 70 57 173 1 1 " x 0 15.9 -.0 31 3 96. *Bolt & nuts are UNC threaded. @ 1.7 ( 1 ") and 15.9 ( 5 8") steel rings are also available upon request. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page 09 for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales 1 GRINNELL reserves the right to change the contents without notice. www.grinnell.com
Shurjoint Model RX-3770 3770 PSI Couplings Shurjoint Tech Data Sheet: O-07 The Shurjoint Model RX-3770 Coupling is designed to provide a fully restrained joint for use with extra-strong carbon steel pipe including API 5L Grade X65 line pipe. The coupling is comprised of two ductile iron heavywall housing segments, rubber gasket (EPDM) and four heat-treated track bolts and nuts. Two steel weld rings are factory supplied with a coupling. 0--,567),,89 Pressure-Temperature Rating Nom. Working Pressure Rating EPDM: Class 60 Bar @38 C 000 :;<=>.0,89?6@A6BC>)(,89 Max. Service Temperature 110 C Nitrile: 8 C *Working pressure is based on API 5L X65 line pipe. M N O V *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum times the working pressure. PQPRSTUT WR ( Nominal ), + +E+.* ),E.1 ).E+1 *E(-,E1-. )E.. +)E. Pipe Max. Working Dimensions Bolt / Nut* Pipe-end Preparation Size OD Pressure A B C R L E Bar Size ). (E+.* ),E-*, ).E-*, 0--, )*E/, ).E/* )/E,.0E), )+E0, )/E(( +E(/,E+.* )),E, (E+0 -E1,,E-*, No.,E(-* )E*,,E.,,E.1.1-E) )-1E* psi in 150 8.3 60 60 31 19 7 8" x 5 1 31 5 7.7 00 19.1 60 39 1 175 1¼" x 5 38 5 9.9 50 73.0 60 0 505 188 1 1 " x 175 19 38 5 79. 300 33.9 60 8 587 19 1 1 " x 175 38 6 11.3 *Bolt & nuts are UNC threaded. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page 09 for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Refer to back cover for country-specific contact information 15
RING JOINT SYSTEMS RING JOINT FITTINGS Shurjoint offers a full range of ring joint fittings for use with Model R-88 ring joint couplings. 8 - ) Models RJ-10, RJ-11 & RJ-60 and RJ-0 are available in cast ductile iron to ASTM A 536 Gr. 65-5-1. weight pipe, ASTM A 53 Gr. B or equivalent, or fabricated from wrought carbon steel of the equivalent properties. request. contact Shurjoint for details. FITTING MATERIAL SPECIFICATIONS Fitting body: ASTM A 395, Gr. 65-5-15. min. tensile strength 81 Bar (65,000 psi). (0.375") wall pipe of ASTM A 3 Gr. WPB Surface Finish: red. (Option) s: General Notes: ratings of installed coupling. working pressure listed (AWWA C606 5..3). depressurized and drained before attempting disassembly and or removal of any components. scalding or hot water services or other high temperature applications. Visit Shurjoint website for full warranty. designs and or standard equipment without notice and without incurring any obligation. * Shurjoint product specifications can be found at www.shurjoint.com GRINNELL reserves the right to change the contents without notice. O[\R (), ). (E+.* -E-*.(E+ C - E Nominal O.D. )1 )1E,,, ),E-*, ).E-*, ),E,, ))E,, /E,, **E, ()E1 --E, 00 19.1 197 13.0 50 73.0 9 5.0 300., )+ )( )+E,,, )(E,,, ).E,,.-E,.,/E, //E, 33.9 5 35.0 350 355.6 80 37.0 00.+.,E,,, 0,E,.,0E+ 06. 305 5.0 50.(.1.1E,,, 0+E, 1(*E, 57. 686 95.0 0,.+E,,, 0/E,, *.)E, 508.0 76 138.0 600 0..(E,,, 1.E,, +,*E, 609.6 91 0.0 01 0,E,,, 1*E,, +/*E, 650 660. 991 37.0 700 0+ 0.E,,, 1(E,, -/.E, 711. 1067 75.0 1, 01E,,, *)E,, (/*E, 750 76.0 113 3.0 800 1. 0+E,,, *1E,, ),,*E, 81.8 119 360.0 11 1,E,,, +,E,, ).1)E, 850 863. 195 07.0 900 1( 11E,,, 1(E,,, 1.E,,, ++E,, +0E,, 91. -.E,, )*,0E, )0+(E, 137 )-/,E, 57.0 1000 10.0 15 56.0 1050 1066.8 00 6.0 1100 1117.6 76 683.0 100 119. 189 81.0 sizes are to manufacturer's standard. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See left column for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Shurjoint Figure RJ-10 90 Elbows O[\R Shurjoint Tech Data Sheet: O-0 www.grinnell.com
Shurjoint Figure RJ-11 5 Elbows Shurjoint Tech Data Sheet: O-0 O[\R (), ). (E+.* 1E.*.,E/ C - E Nominal O.D. )1 )1E,,, ),E-*, ).E-*, *E.* 1E-* +E,, 0/E+ *,E+ *.E( 00 19.1 108 9.5 50 73.0 11 18.0 300., )+ )( )+E,,, )(E,,, ))E.* -E.* ),*E+ ),)E. 33.9 133 3.0 350 355.6 15.0 00.+.,E,,, ).E*, )),E, 06. 18 6.0 50.(.1.1E,,, )*E,, )-+E, 57. 86 8.0 0,.+E,,,.(E,,, 0,E,,, )+E,, 508.0 )(E*, )-E.*.+.E, 318 01(E, 0,1E, 50.0 600 609.6 381 80.0 650 660. 06 119.0 700 0+ 0. 0.E,,, )/E-* 0/+E, 711. 38 138.0 1, 01 0+E,,, 01E,,, 1,E,,,..E.*.1E((.)E,, *,1E, 11/E, +.,E, 750 76.0 80 158.0 800 81.8 50 180.0 850 863. 533 0.0 900 1( 1. 11 11E,,, 1(E,,, 1.E,,,.+E,, 91../E((.-E0/ 565 (/*E, +(1E, -*.E, 9.0 1000 10.0 63 8.0 1050 1066.8 660 311.0 1100 1117.6 696 3.0 100 119. 759 07.0 O[\R O[\R (), ). (E+.* -E-* 1+E. C - E Nominal O.D. )1 )1E,,, ),E-*, ).E-*, ),E,, ))E,, /E,, ),0E1 ))(E( -.E+ 00 19.1 197 1.0 50 73.0 9 33.0., )+ )( )+E,,, )(E,,, )*E*, ).E,,.+(E, )*1E, 300 33.9 5 7.0 350 355.6 80 5.0.+.,E,,, )-E.* 00-E, 00 06. 305 70.0.(.1.1E,,,.,E,, 1++E, 50 57. 39 1.0 0,.+E,,,..E*, -++E, 508.0 38 153.0 0..(E,,, 0,E,,,.0E*,.*E,, (+.E, //.E, 600 609.6 508 1.0 650 660. 57 38.0 0+ 0.E,,,.+E*, ))0*E, 700 711. 597 39.0 1, 01 0+E,,, 01E,,, 1,E,,, 00E,, 0,E,,.(E,, ).(*E, )11*E, )-/,E, 750 76.0 635 51.0 800 81.8 673 5.0 850 863. 711 58.0 1( 1. 11 1(E,,, 1.E,,, 11E,,, 0*E,, 0+E,, 1,E,,.1((E,.,-*E, )(1)E, 900 91. 76 657.0 1000 10.0 838 81.0 1050 1066.8 889 837.0 1100 1117.6 91 93.0 100 119. 10 1131.0 Shurjoint Figure RJ-0 Tee Shurjoint Tech Data Sheet: O-0 18") and larger sizes conform to ANSI B.9. All other sizes are to manufacturer's standard. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Refer to back cover for country-specific contact information 18") and larger sizes and E-E of R-60 650 (6") and larger sizes conform to ANSI B.9. All other sizes are to manufacturer's standard. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales 17
Shurjoint Figure RJ-1 Reducing Tees Shurjoint Tech Data Sheet: O-0 O[\R O[\N )1]). )+]). )+])1 )1E,,,]).E-*, ))E,, ),E+. )1*E, C - E C - B Nominal O.D. )(]). )+E,,,])1E,,, )+E,,,]).E-*, )(E,,,]).E-*, ).E,, ).E,, ).E+. ))E+..1+E, )-+E, )-.E, 350 x 300 355.6 x 33.9 79 70 66.0 00 x 300 06. x 33.9 305 95 78.0 00.,]). )(])1 )(])+ )(E,,,])1E,,, )(E,,,])+E,,, )0E*, )0E,,.*0E,.+1E, x 350 06. x 355.6 305 305 80.0 50 x 300 57. x 33.9 33 31 11.0 50.,])+.,E,,,]).E-*, )0E+../-E, x 350 57. x 355.6 33 330 115.0 50.,])(.,])1.,E,,,])+E,,, x 00.,E,,,])(E,,,.,E,,,])1E,,, 57. x 06. )*E,, )1E,, 33 )1E*, 0,1E, 330 0.(E, 0)-E, 10.0 x 300 508.0 x 33.9 381 36 135.0 x 350 508.0 x 355.6 381 356 138.0.1])+.1])..1E,,,]).E-*, )*E+. 0/+E, x 00 508.0 x 06. 381 356 1.0.1])(.1])1 x 50.1E,,,])(E,,,.1E,,,])+E,,,.1E,,,])1E,,, 508.0 x 57. )-E,, )+E,, 381 )+E*, 368 100E, 1,-E, 1)(E, 19.0 600 x 300 609.6 x 33.9 3 397 180.0 600 x 350 609.6 x 355.6 3 06 185.0 600 x 00 609.6 x 06. 3 06 190.0 600 x 50 609.6 x 57. 3 19 197.0 600 x 609.6 x 508.0 3 3 0.0.1].,.1E,,,].,E,,, )-E,, )-E,, 111E, C-E: Mfr's standard. E-E marked (*): Mfr's standard (made of ductile iron). All other E-E: ANSI B.9. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales 18 GRINNELL reserves the right to change the contents without notice. www.grinnell.com
Shurjoint Figure RJ-50 Concentric Reducer Shurjoint Tech Data Sheet: O-0 Shurjoint Figure RJ-51 Eccentric Reducer Shurjoint Tech Data Sheet: O-0 R[\R )1]). )1E,,,]).E-*, (E,, *)E, E - E Nominal O.D. )(]). )+])1 )+]). )+E,,,])1E,,, )+E,,,]).E-*, )(E,,,]).E-*, /E,, /E*, +1E, -.E+ 350 x 300 355.6 x 33.9 03* 3.0 00 x 300 06. x 33.9 9* 9.0 00.,]). )(])+ )(])1 )(E,,,])+E,,, )(E,,,])1E,,, )*E,, -/E, x 350 06. x 355.6 9* 9.0 50 x 300 57. x 33.9 1* 33.0 50.,])+.,E,,,]).E-*, ),E,, /*E, x 350 57. x 355.6 381 36.0 50.,])(.,])1.,E,,,])1E,,, //E, x 00 57. x 06. 381 36.0.1])..,E,,,])+E,,, ),)E, x 300 508.0 x 33.9 5* 3.0.1])1.,E,,,])(E,,, x 350.1E,,,])1E,,,.1E,,,]).E-*,.,E,, 508.0 x 355.6.,E,, ).E,, ).(E, 508 5.0 x 00 508.0 x 06. 508 6.0 x 50 508.0 x 57. 508 58.0 600.1].,.1])+.1])( x 300.1E,,,].,E,,,.1E,,,])+E,,,.1E,,,])(E,,,.,E,, ).E,, 609.6 x 33.9 305* ).E,, )*1E, )*+E, 70.0 600 x 350 609.6 x 355.6 508 70.0 600 x 00 609.6 x 06. 305* 70.0 600 x 50 609.6 x 57. 508 70.0 600 x 609.6 x 508.0 305* 71.0 C-E: Mfr's standard. E-E marked (*): Mfr's standard (made of ductile iron). All other E-E: ANSI B.9. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales R[\R )+]). )1]). )1E,,,]).E-*, )0E,, *)E, E - E Nominal O.D. )(]). )+])1 )+E,,,])1E,,, )+E,,,]).E-*, /E,, +1E, 350 x 300 355.6 x 33.9 330 3.0 00 )(])+ )(])1 x 300 )(E,,,])+E,,, )(E,,,])1E,,, )(E,,,]).E-*, 06. x 33.9 9* )*E,, )*E,, -(E, 9.0 -/E, 00 x 350 06. x 355.6 9* 9.0 50 x 300 57. x 33.9 381 35.0 50.,])+.,])..,E,,,]).E-*,.,E,, /*E, x 350 57. x 355.6 381 36.0 50.,])(.,])1.,E,,,])1E,,, //E, x 00 57. x 06. 381 36.0.1])..,E,,,])+E,,, ),)E, x 300 508.0 x 33.9 508 3.0.1])1.,E,,,])(E,,, x 350.1E,,,])1E,,,.1E,,,]).E-*, 508.0 x 355.6 ).(E, 508 5.0 x 00 508.0 x 06. 508 6.0 x 50 508.0 x 57. 508 58.0 600.1].,.1])+.1])( x 300.1E,,,].,E,,,.1E,,,])(E,,,.1E,,,])+E,,, 609.6 x 33.9.,E,, 508 )*+E, )*1E, 70.0 600 x 350 609.6 x 355.6 508 70.0 600 x 00 609.6 x 06. 508 70.0 600 x 50 609.6 x 57. 508 70.0 600 x 609.6 x 508.0 508 71.0 C-E: Mfr's standard. E-E marked (*): Mfr's standard (made of ductile iron). All other E-E: ANSI B.9. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Refer to back cover for country-specific contact information 19
0 Shurjoint Figure RJ-60 Cap Shurjoint Tech Data Sheet: O-0 R[\R ), (). (E+.* ).E) E - E Nominal O.D. )1 )1E,,, ),E-*, ).E-*, 0E,,.+E1 )0E. )-E+ 00 19.1 76 5.5 50 73.0 76 6.0., )+ )( )+E,,, )(E,,, 1E,, *E,, 00E, 1+E. 300 33.9 76 8.0 350 355.6 10 1.0.+.,E,,, *-E. 00 06. 10 15.0.(.1.1E,,, +E,, --E, 50 57. 17 1.0 0,.+E,,, )),E, 508.0 15 6.0 0..(E,,, 0,E,,, )0+E, ).0E, 600 609.6 15 35.0 650 660. 67 50.0 0+ 0.E,,,.1(E+ 700 711. 67 56.0 1, 01 01E,,, )+*E, 750 76.0 67 6.0 1. 0+E,,, ),E*, 001E1 800 81.8 67 113.0 11 1,E,,,..1E, 850 863. 67 75.0 1( 11E,,, 1(E,,, 1.E,,, )0E*, ).E,,.1.E,.--E, 0)*E, 900 91. 67 15.0 1000 10.0 305 10.0 1050 1066.8 305 110.0 1100 1117.6 33 16.0 100 119. 33 13.0 and larger sizes conform to ANSI B.9. All other sizes are to manufacturer's standard. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See page for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales GRINNELL reserves the right to change the contents without notice. Shurjoint Figure RJ-70 Flange Adapter Shurjoint Tech Data Sheet: O-0 R[\R (), ). (E+.* + 11E/ E - E Nominal O.D. )1 )1E,,, ),E-*, ).E-*, ( ))(E( /(E) +-E) 00 19.1 15 0. 50 73.0 03 30.5 300., )+ )+E,,, )1-E, 33.9 03.6 350.1 )(.,E,,,.1E,,, )(E,,, 355.6 (E,, (E,, 03.(+E/ )+/E1 )10E, 5.0 00 06. 03 66.8 50 57. 03 65.0 508.0 03 77.0 600 609.6 03 130. 100 119. 03 36.0 1( 1(E,,, (E,, (,,E( E-E: Mfr's standard. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 1 in the General Data section of this book or on www.shurjoint.com. See Flange Drilling Specifications on page 67. See page for specifications For information on alternative sizes, contact a GRINNELL Sales For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales www.grinnell.com