Cooper Bussmann Read and Retain for Future Reference Network Management System QuickStart Guide Version 1.0
Release Notice This is the July 2013 release of the Cooper Bussmann Network Management System QuickStart Guide version 1.0, which corresponds to software version 1.0. Follow Instructions Read this entire manual and all other publications pertaining to the work to be performed before installing, operating, or servicing this equipment. Practice all plant and safety instructions and precautions. Failure to follow the instructions can cause personal injury and/or property damage. Proper Use Any unauthorized modifications to or use of this equipment outside its specified mechanical, electrical, or other operating limits may cause personal injury and/or property damage, including damage to the equipment. Any such unauthorized modifications: (1) constitute misuse and/or negligence within the meaning of the product warranty, thereby excluding warranty coverage for any resulting damage; and (2) invalidate product certifications or listings. 2 www.cooperbussmann.com/wirelessresources
CONTENTS QuickStart Procedures...4 Requirements...4 Before You Begin...4 Device Discovery...5 Configuring the Localhost Location...6 Configuring a Managed Switch/Router...7 Configuring a Wireless Host Gateway...10 Configuring an Agent for a 455U-D Gateway....16 Configuring Remote Wireless Devices...20 www.cooperbussmann.com/wirelessresources 3
QuickStart Procedures Use this QuickStart Guide to configure the Cooper Bussmann Network Management System (Cooper NMS) to monitor managed switches, wireless host gateways, and other remote wireless devices in your network. After you have configured monitoring, you can refer to the Cooper Network Management System User Manual to learn how to customize the Cooper NMS interface to view information that you find most useful. Requirements This guide assumes that you have completed the installation procedures in the Cooper NMS Installation Guide and have already set up the following: A Windows computer with VMware Player virtual machine and the Cooper NMS image installed and set up. Connection to an Ethernet network that includes the devices you want to monitor with Cooper NMS. For example, devices you may want to monitor could include 245U-E Ethernet Modems, 945U-E Ethernet Modems, 915U-2 Wireless Meshing I/O, and 455U-D Serial Modems. Before You Begin If you are not already logged on to Cooper NMS, do so now. Instructions on accessing Cooper NMS are provided in the Cooper NMS Installation Guide. After logging on, you will see the Home Dashboard page shown below. If you are using the trial version of Cooper NMS, the window displays an orange banner with information about the trial period. The banner is removed once a license has been purchased and the license keys are installed. 4 www.cooperbussmann.com/wirelessresources
Device Discovery The procedures in this guide describe how to configure monitoring for the most common wireless network topology (Figure 1). In this topology example, a router/switch is directly connected to the computer running Cooper NMS via a LAN connection, and wireless gateways are also connected to the router/switch via a LAN connection (as indicated by solid lines). The gateways communicate wirelessly with various field stations and repeaters (dashed lines). NOTE As a general rule, devices that are hard-wired to a parent device need to be individually configured. Devices with a wireless connection to a parent device can be auto-discovered via the parent. Figure 1 Example of Typical Network Topology www.cooperbussmann.com/wirelessresources 5
Configuring the Localhost Location Cooper NMS allows you to view a configured network on Google maps. Before configuring the network you need to configure the actual location of the localhost, which is the computer running Cooper NMS. Once the location of the localhost is established, as you configure the network all newly discovered devices will automatically cluster near the localhost on the map, making it easy to drag them to their actual locations. 1. Click Home at the top of the page 2. Click Host Status from the menu. The Host Status page appears, which currently lists only the localhost (the Cooper NMS computer). 3. Click the localhost link in the Host Name column. 4. On the Host Status Details page, click the Monitoring Configuration tab. 5. Click the Google Maps tab. By default, the location of the localhost (as indicated by the red marker) is shown as Dublin California. 6 www.cooperbussmann.com/wirelessresources
6. Drag the red location marker to the actual location of the Cooper NMS computer and click UpDate to save the change. From now on, all newly discovered devices will cluster near the position of the localhost. After each device is discovered, you can manually move it to its exact location on the map. Configuring a Managed Switch/Router If the system you are configuring has a managed switch or router, you need to configure monitoring for this device before other devices. 1. Click Configure at the top of the page. 2. Click Run the Monitoring Wizard. 3. Scroll down the list of devices and click Network Switch/Router to start this Wizard. 4. Enter the following information. Then, click Next to continue. Switch/Router Address The IP address of the switch or router. SNMP Community A user ID or password that allows access to the switch or router device statistics. The default value is Public. Check with your IT department before changing this setting. SNMP Version SNMP version of the switch or router being used. Router Vendor If the vendor is not in the list choose Other/Unknown. Port Naming Scheme You can choose either numbers or description. Scan Interfaces, Bandwidth Monitoring Defaults It is recommended that you confirm these settings with your IT department. The Network Switch/Router monitoring wizard then steps you through the setup. The details vary depending on the type of switch and the parameters that can be monitored. www.cooperbussmann.com/wirelessresources 7
5. Enter the following information, and click Next to continue. Under Switch Details, enter a name to identify the switch/router in the Name field. Under Services, select the Ping checkbox if ping should be used for health checks. Under Bandwidth and Port Status, select the Warning checkbox if you want the bandwidth of a port to be monitored for warning and critical thresholds that you can define. 6. On the Monitoring Settings page, specify how frequently you want the NMS to scan the Switch/Router under 8 www.cooperbussmann.com/wirelessresources
normal operating conditions and alert conditions. When finished, click Next to continue. It is suggested to leave the period at the defaults until the data throughput of the gateway is known. 7. On the Notifications Settings page, specify what to do when a problem is detected or persists, and how alert notifications should be sent and how often. When finished, click Next to continue. 8. Select which groups the switch or router belongs to: Under Host Groups, select Wireless Hosts. Under Service Group, select Wireless Services. Under Parent Host, select the device that is connected as its parent host. Because this device is a Switch/ Router, select Localhost, which is the name of the NMS computer. www.cooperbussmann.com/wirelessresources 9
9. Select Next and continue through the rest of the setup. Configuring a Wireless Host Gateway Use this procedure to configure monitoring for a wireless host gateway. The wireless host gateway is usually the connection point between Cooper NMS and the wireless network, and there is typically a wireless host gateway for each type of network. The following gateways are available: 915U-2 Gateway (Gateway mode must be enabled on the module) 245U-E Ethernet Modem Access Point 945U-E Ethernet Modem Access Point 455U-D Serial Modem Access Point The 455U-D Serial Modem requires a serial-to Ethernet converter (Agent) to communicate with Cooper NMS. By default, Cooper NMS provides this Agent on its COM1 port. Important: If you want to monitor a 455U-D that is not connected directly to the COM1 port on the Cooper NMS computer, you will need to configure an Agent for the 455U-D before you can configure monitoring. Complete the steps in Configuring an Agent for a 455U-D Gateway and then return to this procedure. 10 www.cooperbussmann.com/wirelessresources
1. Click Configure at the top of the page. Cooper Bussmann Network Management System QuickStart Guide 2. Click Run the Monitoring Wizard. www.cooperbussmann.com/wirelessresources 11
3. Click Single Wireless Host. 4. Select the host model and host type from the dropdown lists. Click Next to continue. Host Model Select the gateway you want to monitor. Host Type Select Gateway because the wireless host gateway is the primary gateway between the NMS and the system. 5. Under Basic Setting, enter the following parameters: IP Address The IP address of the wireless host (only available on 915U-2, 245U-E and 945U-E models). Host Name Name of the device or location. Unit Address Only available for 455U-D. This is the unit ID of the 455U-D host. 12 www.cooperbussmann.com/wirelessresources
The example on the left is for a 915U-2 host; the example on the right is for a 455U-D host. 6. If you are adding a 455U-D Modem wireless host, select the name of the Agent from the Agent Name drop down list. If the 455U-D is directly connected to the COM1 port on your computer, select Local Serial Port. This selects the default Agent that is setup internally within Cooper NMS for COM1. 7. Under Host Services, select individual services that you want to monitor or Select All to add all services. Click Next to continue. The list of services shown are for the model you selected in step 4. 8. Enter the status update period. Click Next to continue. The status update period is the interval (in minutes) at which Cooper NMS will request status information from a wireless host. It is suggested to leave the status update period at 5 minutes until the data throughput of the gateway is known. The default period is 5 minutes. www.cooperbussmann.com/wirelessresources 13
9. On the Notifications Settings page, specify what to do when a problem is detected or persists, and how alert notifications should be sent and how often. Click Next to continue. 10. Select the groups that the wireless host belongs to. Click Next to continue. Under Host Groups, select Wireless Hosts. Under Service Group, select Wireless Services. Under Parent Host, select the device that the wireless host gateway is connected to as its parent host. In the following example, Managed Switch is selected because this is the switch/router that was configured in the previous section. Note: If there is only one wireless host gateway and no switch or router is connected, select Localhost, which is the name of the NMS computer. 14 www.cooperbussmann.com/wirelessresources
11. Click Apply to save the configuration of the wireless host. The following screen appears, which allows you to run the Monitor Wizard again or view status of the configured wireless host. www.cooperbussmann.com/wirelessresources 15
Configuring an Agent for a 455U-D Gateway The 455U-D requires either a local or an external Agent for serial-to-ethernet conversion, depending on how the system is configured. There are two primary Agent scenarios: Local Ser2Eth Agent If the 455U-D host is directly connected to COM1 port on the computer on which Cooper NMS is running, the 455U-D automatically uses the default Agent, Ser2Eth, which is setup internally within Cooper NMS for the COM1 port. In this case, no additional configuration is needed. See Scenario 1. External Hardware Agent If the 455U-D gateway is not directly connected to the Cooper NMS computer, an external serial-to-ethernet Agent, such as the 605M-R1 router, is required to be connected to the 455U-D to handle communications with Cooper NMS. See Scenario 2. For Scenario 2, you need to configure the Agent for the 455U-D gateway. Follow the instructions provided in this section. Scenario 1: 455U-D Using Local Ser2Eth Agent 16 www.cooperbussmann.com/wirelessresources
Scenario 2: 455U-D Using External Hardware Agent (605M-R1) 1. Click Configure at the top of the page. 2. Click Serial Agent Config on the menu at the left. www.cooperbussmann.com/wirelessresources 17
The Manage Agents page appears. The list initially shows only the Cooper NMS default Agent, Local Serial Port, which is set up for COM1 (port 2002). 3. Add a new Agent for each 455U-D gateway that is using a 605M-R1 Agent or a software Agent on a remote server: a. On the Manage Agents page, click Add New Agent. b. Configure the following parameters: Agent Name Name that you are assigning to this Agent. IP Address IP address of the device or IP address of the Ethernet to serial converter. Port No. Port number that will be used for the communications. This will need to be the same port as configured on the device. Description Enter a brief description for the device. Inter Command Delay The delay (in seconds) between two consecutive polling commands from Cooper NMS. This delay helps slow communications between Cooper NMS and the gateway so that throughput is not affected. Default is 0. Remote Serial Port Configuration If the device is to be configured remotely, select Yes. 18 www.cooperbussmann.com/wirelessresources
c. If the device is to be configured remotely, provide the following information under Other Settings: Baud Rate Parity Stop Bits Data bits Select flow control, either XON/XOFF, RTS/CTS or locally controlled DCD or DTR d. Click Add Agent to save the configuration. 4. Repeat step 3 to configure additional Agents, if needed. 5. When finished, return to Configuring a Wireless Host Gateway to set up monitoring for the 455U-D. www.cooperbussmann.com/wirelessresources 19
Configuring Remote Wireless Devices Follow these steps to configure monitoring for remote wireless devices that are communicating through the wireless host gateways configured earlier in Configuring a Wireless Host Gateway. Note: To enable scanning of remote 915U-2 Gateways and 455U-D Modems, the modules must be setup for remote or over-the-air configuration. Additionally, the remote devices need to have recently sent data to the 915U-2 or 455U gateway so that these devices are in the gateway s connectivity list. To set up remote or over-the-air configuration for a device, refer to the device user manual. 1. Click Configure at the top of the page. 2. Click Run the Cooper Wireless Auto Discovery Wizard. 3. Click Start a new wireless discovery job. 20 www.cooperbussmann.com/wirelessresources
4. Select the host gateway(s) and access points that you want to use for the wireless discovery scan. 5. Click Submit. The module will scan and locate wireless devices that are communicating with the gateway or access point. The screen does not automatically refresh. 6. Wait 10 seconds then click Refresh Job List to display the number of hosts found. 7. Click the arrow in the Action column for the scanned target to see the results of the wireless discovery scan. 8. Specify the following for each module you want to monitor. Click Next when finished. Select the checkbox next to the module you want to monitor. If this checkbox is not selected, the module will not be saved in the database and cannot be monitored. In the Host Type column, select the host type from the drop-down menu. In the Services column, select the checkbox next to each service that you want to monitor. www.cooperbussmann.com/wirelessresources 21
For 455U-D modules, under Address Path specify the radio repeater path that the 455U uses to communicte. For example, if the communications path is from field station unit #1 through #4 (repeater) to unit #2 (gateway), you would enter R1=4 as it is the first repeater. If there are no repeaters, leave the address path blank. 9. Enter the update period for each host, and click Next to continue. This is the time period the NMS will request status information from a Wireless Host. It is suggested to leave the period at the default of 10 minutes until the data throughput of the gateway is known. 22 www.cooperbussmann.com/wirelessresources
10. On the Notifications Settings page, specify what to do when a problem is detected or persists, and how alert notifications should be sent and how often. Click Next to continue. 11. Select which groups the wireless host belongs to: Under Host Groups select Wireless Hosts. Under Service Group select Wireless Services. www.cooperbussmann.com/wirelessresources 23
12. Click Next to continue. Then, click Apply to save the configuration. The following screen appears, which allows you to run the Monitor Wizard again or view the latest configuration. 13. Click Home at the top of the page, and then click Host Details on the menu at the left. The list of newly discovered devices appears (see example below). 24 www.cooperbussmann.com/wirelessresources
The Cooper Network Management System is now ready to monitor the managed switch, wireless host gateways and other Cooper Wireless devices you have configured. Once you have finished configuring all the devices you want to monitor, create a snapshot and backup as described in the the Cooper Network Management System User Guide. It is recommended that you create snapshots and backups on a regular basis. www.cooperbussmann.com/wirelessresources 25
Notes 26 www.cooperbussmann.com/wirelessresources
Customer Assistance Technical Support: United States:+1 866 713 4409 Australasia.: +61 7 3352 8624 Other: +1 604 944 9247 Email: ELPRO-Support@cooperindustries.com Website: www.cooperbussmann.com/wireless Australasia Fax: +61 7 33528677 US Fax: +1 925 924 8502 Online Resources Visit www.cooperbussmann.com/wirelessresources for the following resources and more: User Manuals Installation Guides Configuration Software Datasheets Dimensional Drawings North America & Latin America 5735 W. Las Positas Suite 100 Pleasanton, California 94588 USA Telephone: +1 925 924 8500 elpro-sales@cooperindustries.com Australia, New Zealand Cooper Technology Centre Suite 2.01, Quad 2, 8 Parkview Drive Sydney Olympic Park, NSW, 2127, AUSTRALIA Telephone: +61 2 8787 2777 elpro-sales@cooperindustries.com China 955 Shengli Road East Area of Zhangjiang High-Tech Park Shanghai, 201201, CHINA Telephone: +86 21 2899 3600 elpro-sales@cooperindustries.com Southeast Asia 2 Serangoon North Avenue 5 # 06-01 Fu Yu Building, 554911, SINGAPORE Telephone: +65 6645 9888 elpro-sales@cooperindustries.com 2013 Cooper Bussmann www.cooperbussmann.com/wireless Your Authorized Cooper Bussmann Distributor is: The trade names and brand names contained herein are valuable trademarks of Cooper Industries in the U.S. and other countries. You are not permitted to use the Cooper Trademarks without the prior written consent of Cooper Industries. www.cooperbussmann.com/wirelessresources 27