Hinrichs Electronic GmbH Creidlitzer Straße 68 D-96450 Coburg Tel: + 49 / (0)9561 / 18400 Fax: + 49 / (0)9561 / 28522 Email: info@hinrichs-electronic.de Technical Documentation Wired Communication Systems of the type series WSV UNIVERSAL
CONTENTS 1. GENERAL...4 1.1 INTENDED USE... 4 1.2 GENERAL INFORMATION ON SYSTEM CONCEPT WITH BASIC CIRCUITS... 4 1.2.1 FUNCTIONAL DIAGRAM OF INTERCOM AMPLIFIER SYSTEM... 4 1.2.2 BASIC CIRCUITRY OF CURRENT VARIATIONS... 5 1.3 USE OF DOCUMENTATION... 13 1.4 COPYRIGHT... 13 1.5 REPAIR AND SPARE PARTS SERVICE, TECHNICAL SUPPORT... 13 1.6 GUARANTEE... 14 2. SAFETY INSTRUCTIONS...15 2.1 WARNINGS... 15 2.2 INTENDED USE OF THE SYSTEM... 15 2.3 INFORMATION ON GENERAL SAFETY REQUIREMENTS.... 15 2.4 PROHIBITION OF UNAUTHORIZED MODIFICATIONS... 16 2.5 REPAIRS AND SERVICE... 16 3. INSTALLATION...17 3.1 OPERATIVE RANGE... 17 3.2 ASSESSMENT OF POSSIBLE DAMAGE... 17 3.3 FIXING OF AMPLIFIER... 17 3.4 WIRING... 18 3.4.1 CONNECTOR... 18 3.4.2. CONNECTION OF SUPPLY VOLTAGE... 19 technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 2 / 43
3.4.3 CONNECTION OF KEY FOR COMMUTATION OF SPEECH CHANNELS... 20 3.4.4 CONNECTION OF MICROPHONES... 20 3.4.5 CONNECTION OF LOUDSPEAKERS... 22 3.4.6 CONNECTION OF HEADSET... 23 3.4.7 CONNECTION OF EXTERNAL VOLUME CONTROL... 26 3.4.8 CONNECTION OF PWM OUTPUTS ON WSV FOR VOLUME CONTROL... 27 3.4.9 CONNECTION OF JUNCTION BETWEEN STATION I AND STATION II... 28 3.5 CONNECTION DIAGRAMS... 29 4. OPERATION...37 4.1 TURNING ON AND OFF... 37 4.2 VOLUME ADJUSTMENT... 37 4.3 SWITCH-OVER OF DIRECTION OF SPEECH... 37 4.4 PLUG-IN OF HEADSET... 37 5. VIEW OF FRONT PANEL...38 6. MAINTENANCE AND REPAIR...40 6.1 MAINTENANCE INSTRUCTIONS... 40 6.2 SAFETY ELEMENT... 40 6.3 REPAIRS... 40 7. TECHNICAL DATA...41 8. CASE...42 technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 3 / 43
1. General 1.1 Intended use The Intercom amplifier is used as intercom system and provides communication between two positions, for example communication between operator s platform and rescue cage of a turntable ladder or a vehicle with integrated lifting working platform. The WSV system variation consists of two separate modules. First of all of the amplifier module proper, and then of a preamplifier module which due to its compact dimensions can be integrated directly into the loudspeaker of station II. 1.2 General information on system concept with basic circuits 1.2.1 Functional diagram of intercom amplifier system after switching on the supply voltage always hears the conversations of I I Hearing via loudspeaker or headset Direction of speech Talking via mikrophone, headset or loudspeaker Transmission of information from to I by pressing key SPEECH DIRECTION SWITCH-OVER I Talking via mikrophone, headset or loudspeaker Direction of speech Hearing via loudspeaker or headset technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 4 / 43
1.2.2 Basic circuitry of current variations 1.2.2.1 Variation : I: with integrated preamplifier I Consisting of with integrated preamplifier LF-signal Selection of direction of speech Key switch-over of direction of speech GND WSV xx OLO x technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 5 / 43
1.2.2.2 Variation : I: / with integrated preamplifier I Consisting of with integrated preamplifier LF-signal Selection of direction of speech Key switch-over of direction of speech GND WSV xx DLO x WSV xx ELO x technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 6 / 43
1.2.2.3 Variation : I: Mikrophone / Loudpeaker / Headset with integrated preamplifier Mikrophone I Consisting of loudspeaker with integrated preamplifier LF-signal Selection of direction of speech Headset GND Key switch-over of direction of speech WSV xx DLD x WSV xx DLE x WSV xx ELD x WSV xx ELE x technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 7 / 43
1.2.2.4 Variation : I: / / Mcrophone I LF- signal Selection of direction of speech Key switch-over of direction of speech WSV xx DLO x WSV xx ELO x WSV I xx DLO WSV I xx ELO technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 8 / 43
1.2.2.5 Variation : I: / / Headset / I LF signal Selection of direction of speech Headset Key switch-over of direction of speech WSV xx DLD x WSV xx DLE x WSV xx ELD x WSV xx ELE x WSV I xx DLO WSV I xx ELO technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 9 / 43
1.2.2.6 Variation : I: / / Headset / Headset I LF- signal Selection of direction of speech Headset Headset Key switch-over of direction of speech WSV xx DLD x WSV xx DLE x WSV xx ELD x WSV xx ELE x WSV I xx OLD WSV I xx OLE technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 10 / 43
1.2.2.7 Variation : I: / / Headset / / Headset I LF signal Selection of directrion of speech Headset Headset Key switch-over of direction of speech WSV xx DLD x WSV xx DLE x WSV xx ELD x WSV xx ELE x WSV I xx DLD WSV I xx DLE WSV I xx ELD WSV I xx ELE technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 11 / 43
1.2.2.8 Variation : I: Headset Headset I Headset Headset LF- signal Selection of direction of speech Key switch-over of direction of speech WSV xx OOD x WSV xx OOE x WSV I xx OOD WSV I xx OOE technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 12 / 43
1.3 Use of documentation This documentation will help you to familiarize with the wired communication system of the type series WSV Universal and to make full use of its operating capabilities. The documentation contains important information on the safe, proper and economical operation of the communication system. Its observance helps to avoid hazards, to minimize installation costs and to avoid unnecessary repair due to improper connection. The documentation should always be available at the scene where the communication system is used and must be read and correctly applied by all persons involved in installation, start-up, operation, maintenance and repair of the communication system. After the first start-up of the communication system this documentation can be used as reference. The table of contents and cross-references in the texts will help you to look up subject areas. In the interest of your own safety please strictly follow all instructions and directions, in particular those of chapter 2 Safety instructions. 1.4 Copyright All information and descriptions are subject to technical modifications which may become necessary to improve the performance of this communication system. All copyright and patent rights for this communication system and all technical documentations pertaining to it remain the property of Hinrichs Electronic GmbH. This documentation is intended for the personnel for installation, start-up, operation, maintenance and repair. It contains descriptions and drawings of a technical nature which may not be duplicated in whole or in part, nor publicized or used for competitive purposes nor made available to others without our authorization. 1.5 Repair and spare parts service, technical support In the event of queries and problems arising with regard to this communication system Hinrichs Electronic will give you comprehensive support: First of all please read this documentation carefully. This will often help to solve your problem. Otherwise you may proceed as follows. Telephone service: For special questions the staff of Hinrichs Electronic will be glad to assist you. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 13 / 43
Sending the communication system to Hinrichs Electronic: Whenever possible please use the packaging in which the unit has been delivered. In general it must be such as to ensure jerk-free transport of the communication system. Please enclose an error list with the defective unit. What Hinrichs Electronic must know: To enable us to help you efficiently and rapidly we need: The serial number and the variation of the communication system: You will find these on the type plate on the case A description of your problem as detailed as possible: Please inform which keys have been pressed and which settings or other actions you have made. Furthermore we need an accurate description of any damage occurred. Shipping address: Hinrichs Electronic GmbH Creidlitzer Straße 68 D-96450 Coburg Tel.: +49 (0) 9561 18400 Fax: +49 (0) 9561 28522 Email: info@hinrichs-electronic.de 1.6 Guarantee Each communication passes comprehensive quality tests before leaving Hinrichs Electronic. In particular an intermittent performance test is made which usually reveals premature failures. Nevertheless it can happen that a functional failure occurs only after prolonged operation. In this case Hinrichs Electronic, following the General Conditions of Supply for Products and Services of the Electrical Industry, gives a guarantee of 12 months. Please note: Hinrichs Electronic will decline any guarantee if modifications or manipulations have been made on the communication system. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 14 / 43
2. Safety instructions 2.1 Warnings In this documentation the following terms and signs are used for particularly important statements: Advice! Special information on the economically and technically correct use of the communication system. Warning! Special statements, rules and prohibitions to prevent damage. Danger! Statements, rules and prohibitions to prevent injury to persons and serious material damage. 2.2 Intended use of the system The communication system WSV Universal is intended exclusively for amplifying LF signals up to a maximum power output of 10 W on 4 Ohm impedance. Suitable for connection are microphones and loudspeakers complying with the specifications given in the technical data. Hinrichs Electronic expressly declines the liability for any damage caused by the non-compliance with the specifications mentioned. Any modification of the system and ancillary units are to be agreed with Hinrichs Electronic in writing. Otherwise the risk will be transferred to the user. The intended use also includes compliance with the procedures and data as specified in this technical documentation. 2.3 Information on general safety requirements. Any work on live components of the amplifier may only be performed by qualified personnel in accordance with national and international regulations. The current VDE regulations must be complied with, in particular VDE 0100, VDE 0550 / 0551, VDE 0700, VDE 0711 and VDE 0860. Maintenance and repair jobs may only be performed by qualified personnel. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 15 / 43
The conductors of the amplifier system are regularly to be checked for insulation faults and fractures. Any fault detected is to be eliminated immediately. It is prohibited to manipulate with easily flammable or combustible liquids at the amplifier system The amplifier system may not be used in an environment in which inflammable gases and fumes may occur. The amplifier system may only be used in clean dry rooms. It is to be protected against the effects of heat. Avoid the penetration of humidity (splash) into the system! The protective paint coating applied in the factory is only a protective measure against the normal humidity of the atmosphere. 2.4 Prohibition of unauthorized modifications All add-ons, modifications, accessories and spare parts not supplied and authorized by Hinrichs Electronic are inadmissible since they may negatively affect the design features of the amplifier system. They can jeopardize the active and passive safety of the system. For such measures it is always necessary to obtain beforehand the authorization by Hinrichs Electronic in writing. Otherwise the liability and guarantee of Hinrichs Electronic will expire. 2.5 Repairs and service Any damage caused by faulty intervention of other companies will cancel the guarantee of Hinrichs Eletronic! Please also see the information in chapter 1.5 "Repair and spare parts service". technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 16 / 43
3. Installation 3.1 Operative range Danger! The Universal intercom amplifier system may not be used in Ex areas! The following must not be present in the environment of the system: easily inflammable or combustible liquids inflammable gases and fumes heat sources excessive humidity excessive contamination strong jerk and vibration sources 3.2 Assessment of possible damage Prior to installation please check the following: Is the packaging damaged? If so, before opening any further, have this confirmed by the forwarding agent, if necessary subsequently. Is the case damaged, or accessories, if any? When moving the system, is there any noise within the case? Is the WSV variation supplied the same as that you have ordered? The variation supplied is marked on the type plate. If you can answer Yes to any of these questions, please contact Hinrichs Electronic before continuing the installation. Remark! There is no potentiometer at the front panel of the WSV in plants with external volume control or in plants where the volume is regulated via a PWM signal. 3.3 Fixing of amplifier The case of the amplifier is to be fixed with 4 screws M4. Make sure it is fastened securely. The casing must have a well conductive connection to the chassis! Drill distances of case: see chapter 8. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 17 / 43
3.4 Wiring 3.4.1 Connector X2 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 36 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 X1 I 20 19 22 23 24 13 14 15 16 30 31 32 34 35 2 3 X3 Technical data for the 2 x18-pin multiway connector Product: Type series: Basic grid: PHOENIX-CONTACT COMBICON connector 2 x 18-pin 5.0mm Connections: Rigid conductor: Flexible conductor: Flexible conductor with sleeve-joint: Flexible conductor with sleeve-joint and plastic sleeve: Conductor size: 0.2... 2.5mm² 0.2... 2.5mm² 0.25... 2,.5mm² 0.25... 2.5mm² 24... 12 AWG Advice! Install all conductors in such a way that they are absolutely free from pull and not at risk of being sheared or crushed! technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 18 / 43
3.4.2. Connection of supply voltage Warning! The amplifier system may only be operated with the supply voltage marked on the type plate. Prior to installation make sure that the supply voltage of the amplifier complies with the onboard voltage of your vehicle or with the supply voltage available. Two supply voltage ranges can be selected: : 12 VDC ( +/- 10% ) : 24 VDC ( +/- 10% ) Remark: A Multifuse element is integrated in the element. This is a resettable fuse that after release by short circuit or excess current may be reset automatically by switching ON and OFF the supply voltage. Advice! It is recommended to have a pre-fuse protection with a nominal current of 5A. WSV System ON 5A/T X1/18 X1/1 GND - + Clamp X1/1 (GND) and casing must have a well conductive connection to the chassis! technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 19 / 43
3.4.3 Connection of key for commutation of speech channels The key for commutation of speech channels is not included in the scope of supply. Generally any key with the following specifications can be connected: Key data of key: Contact: NOC Breaking voltage: >30V DC Switching current: >10mA Contact material: Au / Ag WSV X1/6 X1/7 3.4.4 Connection of microphones Depending on the variation it is possible to connect dynamic microphones as well as Elektret microphones. Key data of dynamic microphones: No-load sensitivity at 1kHz: 1-2 mv/pa +/-3dB Impedance: abt. 200 Ohm WSV WSV I X1/14 X3/14 X1/15 X3/15 X1/16 X3/16 technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 20 / 43
Key data of Elektret microphones: No-load sensitivity at 1kHz: 5-20mV/Pa +/-3dB Impedance: 1000 2000 Ohm Operating voltage: 1.5 9 V Current consumption: < 0.5mA WSV WSV I +5V X1/14 +5V X3/14 NF NF X1/15 X3/15 X1/16 X3/16 Remarks: The voice reproduction of microphones may be widely differing! Prior to use it is recommended to test the quality! In case of poor voice reproduction therefore first check the microphone and then the amplifier system. s with testesd usability may be obtained from Hinrichs Electronic. Important advice on microphone lines: lines must have a screening with high screening effect! The microphone lines may not be longer than 2m! Voltage supply for special microphones s or microphone speakers with a digital signal processor need an additional voltage supply. WSV WSV I X1/13 OUT +5V/10mA X3/13 OUT +5V/10mA technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 21 / 43
3.4.5 Connection of loudspeakers Warning! s with integrated pre-amplifier ( I ) may not be connected to as loudspeaker. Connect loudspeakers with the following specifications: Impedance: > / = 4 Ohm (Recommended: 4...8 Ohm) Conductor cross section: > 0,75 mm² Please note: The necessary conductor cross section depends on the length of the cable! For WSV variations where the loudspeaker also serves as microphone it is recommended to use only loudspeakers with good microphone performance. WSV WSV I X1/2 X1/3 X3/2 X3/3 Connection of a secondary loudspeaker to It is possible to connect an additional loudspeaker to. To that end it has its own amplifier stage, i.e. the connection can double the output. WSV X1/4 X1/5 Remark: When the headset is plugged the secondary loudspeaker is not muted. s with tested usability may be obtained from Hinrichs Electronic. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 22 / 43
3.4.6 Connection of headset Headsets with the following specifications may be connected: capsule: According to variation it is possible to connect dynamic microphone capsules al well as Elektretmicrophone capsules. Key data of dynamic microphone capsules: No-load sensitivity at 1kHz: 1-2 mv/pa +/-3dB Impedance: abt. 200 Ohm WSV WSV I X2/22 X3/22 X2/24 X3/24 X2/19 X3/19 Key data of Elektret microphone caspules: No-load sensitivity at 1kHz: 5-20mV/Pa +/-3dB Impedance: 1000 2000 Ohm Operating voltage: 1.5 9 V Current consumption: < 0.5mA WSV WSV I +5V X2/22 +5V X3/22 NF NF X2/24 X3/24 X2/19 X3/19 technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 23 / 43
Earphone(s): Headset with one earphone Key data of earphone(s): Impedance: 4...500 Ohm Output: 1-500mW (adaptable) WSV WSV I X2/23 X3/23 X2/24 X3/24 Headset with two earphones Headsets with two earphones can be connected in series or in parallel according to impedance. WSV X2/23 X2/24 Earphones connected in series WSV X2/23 Earphones connected in parallel X2/24 technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 24 / 43
Connection of headset talking key on WSV In headset operation the key for switch-over of speech channels may be used to commute the direction of speech. If the headset has its talking key this can be connected as shown in the following picture. WSV X2/25 X2/21 Identification: Headset plugged / not plugged The bridge is to be inserted into the plug of the headset. It serves to identify Headset plugged/ not plugged. If the headset is plugged the connected microphone of the relevant station is automatically deactivated and the loudspeaker is muted. WSV WSV I X2/20 X3/20 X2/19 Bridge in plug of headset X3/19 Bridge in plug of headset Remark: Please inform Hinrichs Electronic about the type of headset to be used. In this case it is possible to preset the unit in the factory for an optimal adaptation of the headset to the amplifier system. Attention! Avoid overloading the earphones! Connection lines to external headset junction boxes should be screened! Headsets with tested usability may be obtained from Hinrichs Electronic. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 25 / 43
3.4.7 Connection of external volume control Remark: External volume controls can only be connected to systems with the variation number E. See type plate WSV WSV E In this variation the two volume controls in the front panel of are missing. WSV X1/8 yellow X1/9 brown External volume control X1/10 white X2/26 yellow X2/27 brown External volume control I X2/28 white Layout of external volume controls 60mm Length of cable: 1m 25mm Screw socket Insulating sheath Cable to multicore cable end Knurled nut Rotary button technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 26 / 43
3.4.8 Connection of PWM outputs on WSV for volume control Remark: PWM signals for volume control can only be connected to systems with variation number P. See type plate WSV WSV P In this variation the two volume controls in the front panel of are missing. Specification of PWM inputs ( WSV side ) Basic frequency: 500Hz Input amplitude: 5 Vs - 24 Vs WSV X1/11 Volume control via external PWM signal X2/29 Volume control via external PWM signal I X1/12 Common chassis for PWM signals Table: Ratio between output and pulse duty factor of PWM signal Pulse duty factor Percentage sine output Final stages T on T off 0% = 0ms 100% = 2,0ms 0% 10% = 0,2ms 90% = 1,8ms 2% 20% = 0,4ms 80% = 1,6ms 5,5% 30% = 0,6ms 70% = 1,4ms 8,5% 40% = 0,8ms 60% = 1,2ms 12,5% 50% = 1,0ms 50% = 1,0ms 18,5% 60% = 1,2ms 40% = 0,8ms 26,5% 70% = 1,4ms 30% = 0,6ms 38% 80% = 1,6ms 20% = 0,4ms 52% 90% = 1,8ms 10% = 0,2ms 71% 100% = 2,0ms 0% = 0 ms 100% technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 27 / 43
3.4.9 Connection of junction between and I The connection between and I requires a screened four-core conductor. Conductor cross section: Please note: > / = 0,75 mm² To prevent deterioration of the voice quality by interference over metallic circuits the following is to be observed when laying the cable: Whenever technically possible avoid laying the connection line in parallel to other lines. Should this not be possible due to technical reasons, use only screened lines with high screening effect. The screening of this line is to be grounded on both sides. WSV WSV I X2/31 X2/30 X2/32 LF -signal Selection of direction of speech X3/31 X3/30 X3/32 X2/34 X2/35 I GND I X3/34 X3/35 Functions of single cores LF signal Transmission of LF signal Direction of speech I to amplified LF signal from preamplifier I to input final stage Direction of speech to I amplified LF signal from final stage to loudspeaker I Selection of direction of speech Key switch-over of speech channel not actuated: I talking hearing: U = 0V Key switch-over of speech channel actuated: talking I hearing: U = + / GND Supply voltage for preamplifier I Remark: A Multifuse element is integrated in the amplifier to protect the preamplifier of I. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 28 / 43
3.5 Connection diagrams Connection diagram Variation : I: with integrated preamplifier I X1/2 X1/3 X1/6 X1/7 Key switch-over of speech channel PC board preamplifier X2/31 X2/30 X2/32 LF signal Selection of direction of speech 4 3 X2/34 X2/35 System ON I GND I 1 2 X1/18 X1/1 GND with integrated preamplifier technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 29 / 43
Connection diagram Variation : I: / with integrated preamplifier I X1/14 X1/15 X1/16 X1/2 X1/3 X1/6 X1/7 Key switch-over of speech channel PC board preamplifier X2/31 X2/30 X2/32 LF signal Selection of direction of speech 4 3 X2/34 X2/35 System ON I GND I 1 2 X1/18 X1/1 GND with integrated preamplifier technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 30 / 43
Connection diagram Variation : I: / / Headset with integrated preamplifier I X1/14 X1/15 X1/16 X1/2 X1/3 X1/6 X1/7 Key switch-over of speech channel X2/22 X2/23 X2/24 Earphone X2/20 X2/19 Bridge Headset plugged Headset X2/31 X2/30 X2/32 LF signal Selection direction of speech 4 3 PC board preamplifier X2/34 X2/35 System ON I GND I 1 2 X1/18 X1/1 GND with integrated preamplifier technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 31 / 43
Connection diagram Variation : I: / / I X1/14 X1/15 X3/14 X3/15 X1/16 X3/16 X1/2 X1/3 X3/2 X3/3 X1/6 Key switch-over speech channel X1/7 X2/31 X2/30 X2/32 LF- signal Selection of direction of speech X3/31 X3/30 X3/32 X2/34 X2/35 System ON I GND I X3/34 X3/35 X1/18 X1/1 GND technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 32 / 43
Connection diagram Variation : I: / / Headset / I X1/14 X1/15 X3/14 X3/15 X1/16 X3/16 X1/2 X1/3 X3/2 X3/3 X1/6 Key switch-over speech channel X1/7 X2/22 X2/23 X2/24 Earphone X2/20 X2/19 Bridge Headset plugged Headset X2/31 X2/30 X2/32 LF signal Selection direction of speech X3/31 X3/30 X3/32 X2/34 X2/35 System ON I GND I X3/34 X3/35 X1/18 X1/1 GND technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 33 / 43
Connection diagram Variation : I: / / Headset / Headset I X1/14 X1/15 X1/16 X1/2 X1/3 X3/2 X3/3 X1/6 X1/7 Key switch-over of speech channel X2/22 X3/22 X2/23 X2/24 Earphone X3/23 X3/24 Earphone X2/20 X2/19 Bridge Headset plugged X3/20 X3/19 Bridge Headset plugged Headset Headset X2/31 X2/30 X2/32 LF signal Selection direction of speech X3/31 X3/30 X3/32 X2/34 X2/35 System ON I GND I X3/34 X3/35 X1/18 X1/1 GND technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 34 / 43
Connection diagram Variation : I: / / Headset / / Headset I X1/14 X1/15 X3/14 X3/15 X1/16 X3/16 X1/2 X1/3 X3/2 X3/3 X1/6 X1/7 Key switch-over of speech channel X2/22 X3/22 X2/23 X2/24 Earphone X3/23 X3/24 Earphone X2/20 X2/19 Bridge Headset plugged X3/20 X3/19 Bridge Headset plugged Headset Headset X2/31 LF- signal X3/31 X2/30 X3/30 X2/32 Selection direction of speech X3/32 X2/34 I X3/34 X2/35 GND I X3/35 System ON X1/18 X1/1 GND technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 35 / 43
Connection diagram Variation : Headset I: Headset I X1/6 X1/7 Key switch-over of speech channel X2/22 X3/22 X2/23 X2/24 Earphone X3/23 X3/24 Earphone X2/25 X2/21 Key switch-over of speech channel X2/20 X2/19 Bridge Headset plugged X3/20 X3/19 Bridge Headset plugged Headset Headset X2/31 X2/30 X2/32 LF- signal Selection of direction of speech X3/31 X3/30 X3/32 X2/34 X2/35 System ON I GND I X3/34 X3/35 X1/18 X1/1 GND technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 36 / 43
4. Operation 4.1 Turning ON and OFF Turning ON and OFF is by making and breaking the supply voltage. 4.2 Volume adjustment According to the WSV Variation the volume can be adjusted separately for each station via the internal volume controls ( potentiometers ) on the front panel of the connected external volume controls (potentiometers) via the PWM signals. 4.3 Switch-over of direction of speech The direction of speech is switched over by means of the key switch-over of direction of speech. Direction of speech: Key not actuated: I talking, hearing Key actuated: talking, I hearing 4.4 Plug-in of headset When the headset is plugged the microphone is automatically deactivated and the loudspeaker is muted. Remark! A secondary loudspeaker connected to is not muted. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 37 / 43
5. View of front panel I Function of the LEDs LED in STATUS Power Lights up after switching on the supply voltage Supply voltage is OK. LED in ERROR Talk Selection Lights up when the key switch-over of direction of speech is actuated. Headset plugged Lights up when the headset is plugged into. Power Lights up when supply voltage is exceeded or falls below 12V DC - Variation: 10V DC < > 14,5V DC 24V DC - Variation: 21V DC < > 29V DC Talk Selection Flashes when line Talk Selection has ground contact. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 38 / 43
Volume control in VOLUME The volume can be adjusted separately for each station Symbol Headset Volume control to adjust the basic volume for headset at station I I Volume control to adjust the basic volume for headset at station II Volume control to adjust the volume at station I Function of the LEDs of PC board preamplifier I Power Lights up after switching on the supply voltage Supply voltage OK. Talk Selection Lights up when key Talk Selection is actuated. Power Talk Selection technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 39 / 43
6. Maintenance and repair 6.1 Maintenance instructions Check if all line and plug connections are firmly seated. 6.2 Safety element A Multifuse element is integrated in the intercom amplifier. This is a resettable fuse that after release by short circuit or excess current may be reset automatically by switching ON and OFF the supply voltage. 6.3 Repairs It is recommended to have repairs made only by Hinrichs Electronic and also to purchase spare parts from them. Please enclose an error list with the defective unit! technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 40 / 43
7. Technical data Operating voltage range: According to variation: U B: + 12V DC ( + / - 10% ) U B: + 24V DC ( + / - 10% ) Current consumption: 12V DC - Variation: I No-load: I Full load: I Preamplifier: 140mA 580mA 22mA 24V DC - Variation: I No-load: 180mA I Full load: 1,12A I Preamplifier: 18mA * Full load: Two loudspeakers with 4 Ohm impedance each Output: 12V DC Variation: P Sinus : 2 x 5 W to 4 Ohm / 1kHz P Sinus : 2 x 2,5 W to 8 Ohm / 1KHz P Sinus I : 5 W to 4 Ohm / 1kHz P Sinus I : 2,5 W to 8 Ohm / 1KHz 24V DC Variation: P Sinus : 2 x 10 W to 4 Ohm / 1kHz P Sinus : 2 x 5 W an 8 Ohm / 1KHz P Sinus I : 10 W to 4 Ohm / 1kHz P Sinus I : 5 W to 8 Ohm / 1KHz Frequency response: 12V DC Variation: f fu-fo: 300Hz - 6,8 khz ( -3dB / 1kHz ) f fu-fo: 220Hz 11,3 khz ( -6dB / 1kHz ) 24V DC Variation: f fu-fo: 450Hz - 6,6 khz ( -3dB / 1kHz ) f fu-fo: 280Hz 8,5 khz ( -6dB / 1kHz ) Admissible temperature range: Admissible rel. air humidity: Admissible jerks: Admissible vibrations: -20...+70 C in operation -25...+85 C when stored 10...85 % in operation 5...90 % when stored up to 2 G within 1 ms in operation up to 4 G within 1 ms when stored up to 0,5 G at10...55 Hz in operation up to 1 G at 10...55 Hz when stored technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 41 / 43
8. Case 127mm 105mm 120mm 130mm 4,5mm High: 45mm 50mm 28mm I 120mm 130mm 4,5mm High: 45mm Case: Case cover: Surface protection: Extruded aluminium section AlMgSi0,5 Aluminium sheet AlMgSi0,5 Synthetic resin baked enamel colour RAL 9005 (black) Weight: : 600g I: 200g Protective system: / I: IP40 technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 42 / 43
Order key WSV Operating voltage 12-12V DC 24-24V DC O - no microphones D - dynamic microphones E - Elektret microphones O - no loudspeaker L - loadspeaker Headset O - no headset D - Headset with dynamic microphone capsule E - Headset with Elektret microphone capsule Volume adjustment I - Control integrated in front panel E - via external potentiometer P - via PWM signal I WSV I Operating voltage 12-12V DC 24-24V DC O - no microphones D - dynamic microphones E - Elektret microphones O - no loudspeaker L - loudspeaker Headset O - no headset D - Headset with dynamic microphone capsule E - Headset with Elektret microphone capsule Please note when ordering: Operating voltage of and I must be the same. technische dokumentation wechselsprechverstärker universal englisch e1.doc Seite 43 / 43