Microsoft Windows XP SP2 and windream

Transcription

1 windream Microsoft Windows XP SP2 and windream windream GmbH, Bochum

2 Copyright by windream GmbH / winrechte GmbH Wasserstr Bochum Issue: 03/ All rights reserved. No part of the contents of this description may be reproduced or transmitted in any form (print, photocopy, or any other form) or by any means without the express written permission of windream GmbH / winrechte GmbH. Important Notes All information and technical specifications in this description have been collected by the authors with great care. They cannot, however, either guarantee, take legal responsibility or make any other warranty for the results from the use of this information. We would also like to point out that all software and hardware logos and names in this desription are the exclusive property of the trademark, brandname or patent right holders. These are naturally protected by the appropriate laws and trade agreements.

3 Content i Content Microsoft Windows XP SP 2 and windream 1 Adjusting the configuration 1 Additional settings in windream SOLO (standalone version) 5

4

5 Microsoft Windows XP SP 2 and windream 1 Microsoft Windows XP SP 2 and windream Adjusting the configuration This document will help you to configure a windream client PC (windream version 3.x) after the installation of service pack 2 for Microsoft Windows XP. To avoid operating trouble and to guarantee the proper operation of windream, the following adjustments have to be done on the windream client PC: Install the driver-patch Change a registry-key for the indexing service Adjust the configuration of the Windows XP Firewall 1. Install the driver-patch If the windream version used is older than (5), a new driverpathc has to be installed. Else it could come to system failures. The patch can be downloaded from Patches.zip 2. Change a registry-key for the indexing service For the indexing service the following key has to be changed in the registry. Under [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\C ontrol\lsa] the value for everyoneincludesanonymous has to be set to 1: everyoneincludesanonymous=dword: Alternatively you can activate this setting in the local security policy administration dialog:

6 2 Microsoft Windows XP SP 2 and windream Figure 1: Adjusting local Security Settings 1. Start the Local Security Settings (by Start>Settings>Control Panel>Administrative Tools>Local Security Policy). 2. Switch to the folder Local Policies>Security Options. 3. Enable the Policy: Network access: Allow 'Everyone' permission for anonymous users. 3. Adjust the configuration of the Windows XP Firewall The Windows XP Firewall has to be configured in the following way: 1. Start Windows XP Firewall (by Start>Settings>Control Panel). 2. Choose the Index Tab Exceptions. 3. Add to the list of Programs and Services the applications WmIdxSv.exe and wmcc.exe. 4. For this click on the button Add Program... Choose in the dialog box Add a program with Browse... the mentioned programs one after the other.

7 Microsoft Windows XP SP 2 and windream 3 Figure 2: Adjusting the Windows Firewall Adjusting the program settings Now adjust the configuration of both programs WmIdxSv.exe and wmcc.exe according to their requirements. 5. Mark the first program in the list (e.g. WmIdxSv.exe) and click on Edit. Figure 3: Edit a program 6. Activate the command button Change scope...

8 4 Microsoft Windows XP SP 2 and windream In the dialog box Change Scope execute the necessary adjustments according to your requirements. Figure 4: Change scope Configuring the port for DCOM Now the DCOM-Port has to be configured. 7. Click on the command button Port... (Tabpage Exeptions in dialog box Windows-Firewall). Figure 5: Add a port 8. Enter in the field Name DCOM, and in the field Portnumber Click the command button OK to save the adjustments. Now you have executed the necessary adjustments. Close the dialog box Windows Firewall via command button OK. Done.

9 Microsoft Windows XP SP 2 and windream 5 Additional settings in windream SOLO (standalone version) Problem: Access denied when trying to start the vfs-service or the windream configuration 'filter' or the windream management console (WMC). The eventlog shows (when the installation was done with Mainuser = 'Administrator') Src: DCOM Desc: application specific local activation {E36D3A64-1FCE-11D3-B2EF B066E1A} WINDREAMSOLO Administrator S and/or 0016 DCOM Desc: application specific local activation {E36D3A64-1FCE-11D3-B2EF B066E1A} NT-AUTORITY SYSTEM S Reason: xp sp2 has new dcom authorizations. In addition to 'Start' there is a new 'Activation' authorization. The following settings have to be changed (Taskbar)Start - Execute - Dcomcnfg - Component Services - Computer - My Computer - DCOM-config - windream DMS-service (right mouseclick - properties) - Security - Launch and Activation Permissions a) 'customize' must be activated. (not 'Use Default') Click button to open the configuration dialog. b) On tabpage 'Launch Permission' set the Right 'Local Activation' separately for: - group: windream-users

10 6 Microsoft Windows XP SP 2 and windream - System - windream mainuser Important: 'Local Launch' and 'Remote Launch' must not be activated (empty check-mark). When using the dms-service locally the 'remote activation' is not necessary, but it can be activated. The attached screenshot shows the configuration, when 'Administrator' is the windream Mainuser. There is only the group 'windream-benutzer' selected. But also for the other two (Administrator, System) this right has to be activated, too. c) The same configuration for the DCOM start authorization has to be done for the windream Thumbnail service, if you want to use the service. Figure 6: Settings in windream SOLO