Cisco Nexus 7000 Hardware Architecture BRKARC-3470
|
|
|
- Willa Bryan
- 10 years ago
- Views:
Transcription
1 Cisco Nexus 7000 Hardware Architecture BRKARC-3470
2 Session Goal To provide you with a thorough understanding of the Cisco Nexus 7000 switching architecture, supervisor, fabric, and I/O module design, packet flows, and key forwarding engine functions This session will not examine Unified I/O, DCB, FCoE, NX- OS software architecture, or other Nexus platforms Related sessions: BRKARC-3471: Cisco NXOS Software Architecture 2 2
3 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 3
4 Nexus 7010 Chassis System status LEDs ID LEDs on all FRUs Front-toback airflow Integrated cable management with cover Air exhaust Optional locking front doors System fan trays Locking ejector levers Supervisor slots (5-6) I/O module slots (1-4, 7-10) 21RU Fabric fan trays Two chassis per 7 rack Crossbar fabric modules Power supplies Air intake with optional filter Front N7K-C7010 Rear Common equipment removes from rear 4
5 Integrated cable management Nexus 7018 Chassis System status LEDs Optional front door Supported in NX-OS release 4.1(2) and later System fan trays Side-to-side airflow Supervisor slots (9-10) 25RU Crossbar fabric modules I/O module slots (1-8, 11-18) Common equipment removes from rear Power supply air intake Power supplies Front N7K-C7018 Rear 5
6 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 6
7 Supervisor Performs control plane and management functions Dual-core 1.66GHz Intel Xeon processor with 4GB DRAM 2MB NVRAM, 2GB internal bootdisk, compact flash slots Out-of-band 10/100/1000 management interface Always-on Connectivity Management Processor (CMP) for lights-out management Console and auxiliary serial ports USB ports for file transfer N7K-SUP1 ID LED Status LEDs AUX Port Console Port Management Ethernet Compact Flash Slots Reset Button USB Ports CMP Ethernet 7
8 Management Interfaces Management Ethernet 10/100/1000 interface used exclusively for system management Belongs to dedicated management VRF Prevents data plane traffic from entering/exiting from mgmt0 interface Cannot move mgmt0 interface to another VRF Cannot assign other system ports to management VRF Connectivity Management Processor (CMP) Ethernet Connects to standalone, always-on microprocessor on supervisor engine Runs lightweight software with network stack Completely independent of NX-OS on main CPU Provides lights out remote management and disaster recovery via 10/100/1000 interface Removes need for terminal servers 8
9 Supervisor Architecture To Modules To Fabrics To Modules n * 23G Switched Gigabit Ethernet Fabric ASIC Arbitration Path Switched EOBC VOQs Arbitration Path Central Arbiter 128MB 16MB 1GE EOBC 1GE Inband DRAM Flash System Controller 4GB CMP 266MHz DRAM Security Link Processor Encryption 2MB Main 2GB NVRAM CPU Internal CF PHY 1.66GHz PHY OBFL Dual-Core 10/100/1000 Flash 10/100/1000 Console AUX Mgmt Enet slot0: log-flash: usb usb usb CMP Enet 9
10 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 10
11 8-Port 10GE I/O Module N7K-M108X2-12L 8-port 10G with X2 transceivers 80G full-duplex fabric connectivity Two integrated forwarding engines (120Mpps) Support for XL forwarding tables (licensed feature) 8 ports wire-rate L3 multicast replication 802.1AE LinkSec N7K-M108X2-12L 11
12 EOBC 8-Port 10G XL I/O Module Architecture N7K-M108X2-12L To Fabric Modules To Central Arbiter Fabric ASIC LC CPU VOQs Forwarding Forwarding VOQs Replication Replication Replication Replication 10G MAC 10G MAC 10G MAC 10G MAC 10G MAC 10G MAC 10G MAC 10G MAC Linksec Linksec Linksec Linksec Linksec Linksec Linksec Linksec Front Panel Ports 12
13 32-Port 10GE I/O Module N7K-M132XP port 10G with SFP+ transceivers 80G full-duplex fabric connectivity Integrated 60Mpps forwarding engine Oversubscription option for higher density (up to 4:1) 8 ports wire-rate L3 multicast replication 802.1AE LinkSec N7K-M132XP-12 Presentation_ID 2010 Cisco and/or its affiliates. Cisco All Public rights reserved. Cisco Public 13
14 Shared vs. Dedicated Mode To Fabric rate-mode shared (default) 10G Shared mode Four interfaces in port group share 10G bandwidth To Fabric rate-mode dedicated 10G Port group group of contiguous even or odd ports that share 10G of bandwidth (e.g., ports 1,3,5,7) Dedicated mode First interface in port group gets 10G bandwidth Other three interfaces in port group disabled 14
15 EOBC 32-Port 10G I/O Module Architecture N7K-M132XP-12 To Fabric Modules To Central Arbiter Fabric ASIC LC CPU VOQs Forwarding VOQs Replication Replication Replication Replication 10G MAC 10G MAC 10G MAC 10G MAC 10G MAC 10G MAC 10G MAC 10G MAC 4:1 Mux + Linksec 4:1 Mux + Linksec 4:1 Mux + Linksec 4:1 Mux + Linksec :1 Mux + Linksec 4:1 Mux + Linksec 4:1 Mux + Linksec 4:1 Mux + Linksec Front Panel Ports 15
16 48-Port 1G I/O Modules N7K-M148GT-11, N7K-M148GS-11, N7K-M148GS-11L Three 1G I/O module options: 48 10/100/1000 RJ-45 ports (N7K-M148GT-11) 48 1G SFP ports (N7K-M148GS-11) 48 1G SFP ports with XL forwarding engine (N7K-M148GS-11L) N7K-M148GT-11 Release 4.0(1) and later Integrated 60Mpps forwarding engine 46G full duplex fabric connectivity Line rate on 48-ports with some local switching 48 ports wire-rate L3 multicast replication 802.1AE LinkSec N7K-M148GS-11 Release 4.1(2) and later N7K-M148GS-11L Release 5.0(2) and later Presentation_ID 2010 Cisco and/or its affiliates. Cisco All Public rights reserved. Cisco Public 16
17 48-Port 1G I/O Modules Architecture N7K-M148GT-11, N7K-M148GS-11, N7K-M148GS-11L EOBC To Fabric Modules To Central Arbiter Fabric ASIC LC CPU VOQs Replication Forwarding Replication 12 x 1G MAC 12 x 1G MAC 12 x 1G MAC 12 x 1G MAC Linksec Linksec Linksec Linksec Linksec Linksec Front Panel Ports 17
18 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 18
19 Forwarding Hardware Hardware forwarding engine(s) integrated on every I/O module 60Mpps per forwarding engine Layer 2 bridging with hardware MAC learning 60Mpps per forwarding engine IPv4 and 30Mpps IPv6 unicast IPv4 and IPv6 multicast support (SM, SSM, bidir) RACL/VACL/PACLs Policy-based routing (PBR) Unicast RPF check and IP source guard QoS remarking and policing policies Ingress and egress NetFlow (full and sampled) Hardware Table M1 Modules M1-XL Modules without License M1-XL Modules with License FIB TCAM 128K 128K 900K Classification TCAM (ACL/QoS) 64K 64K 128K MAC Address Table 128K 128K 128K NetFlow Table 512K 512K 512K 19
20 Scalable Services License Forwarding engines on M1-XL I/O modules always have XL capacity Access to additional capacity controlled by presence of Scaleable Services license License applies to entire system (per-chassis) N7K# show license usage Feature Ins Lic Status Expiry Date Comments Count SCALABLE_SERVICES_PKG Yes - In use Never - LAN_ADVANCED_SERVICES_PKG Yes - In use Never - LAN_ENTERPRISE_SERVICES_PKG Yes - In use Never N7K# 20
21 Forwarding Architecture Forwarding engine chipset consists of two ASICs: Layer 2 Ingress and egress SMAC/DMAC lookups Hardware MAC learning IGMP snooping and IP-based Layer 2 multicast constraint Layer 3 IPv4/IPv6 Layer 3 lookups ACL, QoS, NetFlow and other processing Linear, pipelined architecture every packet subjected to both ingress and egress pipeline Enabling features does not affect forwarding engine performance 21 21
22 Forwarding Pipelined Architecture FE Daughter Card Ingress NetFlow collection Ingress ACL and QoS classification lookups Layer 3 Ingress Pipeline Egress Pipeline Egress NetFlow collection Egress policing FIB TCAM and adjacency table lookups for Layer 3 forwarding ECMP hashing Multicast RPF check Ingress policing Unicast RPF check Ingress MAC table lookups IGMP snooping lookups IGMP snooping redirection Egress ACL and QoS classification lookups Layer 2 Egress MAC lookups IGMP snooping lookups Packet Headers from Final lookup result to I/O Module Replication I/O Module Replication 22
23 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 23
24 Crossbar Switch Fabric Module Each fabric module provides 46Gbps per I/O module slot Up to 230Gbps per slot with 5 fabric modules Currently shipping I/O modules do not leverage full fabric bandwidth Maximum 80G per slot with 10G module Future modules leverage additional available fabric bandwidth Access to fabric controlled using QoS-aware central arbitration with VOQ N7K-C7010-FAB-1 N7K-C7018-FAB-1 24
25 Fabric Module Capacity 2 x 23G channels per I/O module slot 46Gbps/slot Fabric Modules Crossbar Fabric ASICs 1 1 x 23G channel per supervisor slot 46Gbps/slot Crossbar Fabric ASICs 2 184Gbps 138Gbps 230Gbps 46Gbps 92Gbps per slot bandwidth 46Gbps/slot 46Gbps/slot Crossbar Fabric ASICs Crossbar Fabric ASICs Gbps/slot Crossbar Fabric ASICs 5 Nexus
26 I/O Module Capacity 1G modules Require 1 fabric for full bandwidth Require 2 fabrics for N+1 redundancy 46Gbps/slot 46Gbps/slot Fabric Modules Crossbar Fabric ASICs Crossbar Fabric ASICs Gbps 138Gbps 230Gbps 46Gbps 92Gbps per slot bandwidth 46Gbps/slot Crossbar Fabric ASICs 3 4th and 5th fabric modules provide additional redundancy and future-proofing 46Gbps/slot Crossbar Fabric ASICs 4 10G modules Require 2 fabrics for full bandwidth Require 3 fabrics for N+1 redundancy 46Gbps/slot Crossbar Fabric ASICs 26 5
27 Access to Fabric Bandwidth Access to fabric controlled using central arbitration Arbiter ASIC on supervisor engine provides fabric arbitration Bandwidth capacity on egress modules represented by Virtual Output Queues (VOQs) at ingress to fabric I/O modules interface with arbiter to gain access to VOQs 27
28 What Are VOQs? Virtual Output Queues (VOQs) on ingress modules represent bandwidth capacity on egress modules If VOQ available on ingress to fabric, capacity exists at egress module to receive traffic from fabric Central arbiter determines whether VOQ is available for a given packet Bandwidth capacity represented by credits Credits are requested by I/O modules and granted by arbiter VOQ is virtual because it represents EGRESS capacity but resides on INGRESS modules It is still PHYSICAL buffer where packets are stored Note: VOQ is not equivalent to ingress or egress port buffer or queues Relates ONLY to ASICs at ingress and egress to fabric 28
29 Benefits of Central Arbitration with VOQ Ensures priority traffic takes precedence over besteffort traffic across fabric Four levels of priority for each VOQ destination Ensures fair access to bandwidth for multiple ingress ports transmitting to one egress port Central arbiter ensures all traffic sources get appropriate access to fabric bandwidth, even with traffic sources on different modules Prevents congested egress ports from blocking ingress traffic destined to other ports Mitigates head-of-line blocking by providing independent queues for individual destinations across the fabric In future, will provide lossless service for FCoE traffic across the fabric Can provide strict priority and backpressure (blocking instead of dropping) for certain traffic classes, such as SAN traffic 29 29
30 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 31
31 Layer 2 Forwarding MAC table is 128K entries (115K effective) Hardware MAC learning CPU not directly involved in learning All modules have copy of MAC table New learns communicated to other modules via hardware flood to fabric mechanism Software process ensures continuous MAC table sync Spanning tree (PVRST or MST) or Virtual Port Channel (VPC) ensures loop-free Layer 2 topology 32
32 Layer 2 Forwarding Architecture Layer 2 Forwarding Manager (L2FM) maintains central database of MAC tables L2FM Supervisor L2FM keeps MAC table on all forwarding engines in sync L2FM-Client process on I/O modules interfaces between L2FM and hardware MAC table n7010# sh processes cpu egrep PID l2fm PID Runtime(ms) Invoked usecs 1Sec Process l2fm n7010# attach mod 9 Attaching to module 9... To exit type 'exit', to abort type '$.' Last login: Mon Apr 21 15:58: from sup02 on pts/0 Linux lc _mvl401-pc_target #1 Fri Mar 21 23:26:28 PDT 2009 ppc GNU/Linux module-9# sh processes cpu egrep l2fm l2fmc module-9# L2FM-C L2FM-C Hardware Hardware I/O Module I/O Module Hardware MAC Table Hardware MAC Learning L2FM-C Hardware I/O Module 33
33 Hardware Layer 2 Forwarding Process MAC table lookup in Layer 2 based on {VLAN,MAC} pairs Source MAC and destination MAC lookups performed for each frame Source MAC lookup drives new learns and refreshes aging timers Destination MAC lookup dictates outgoing switchport 34
34 L2 Packet Flow HDR = Packet Headers DATA = Packet Data CTRL = Internal Signaling Credit grant for fabric access 9 Supervisor Central Arbiter Return credit to pool 12 Fabric Module 1 Fabric Module 2 Fabric Module 3 VOQ arbitration and queuing 8 Submit packet headers for lookup 2nd stage ingress port QoS Receive packet from wire 1 Transmit to fabric 4 3 e1/1 10 Fabric ASIC VOQs Replication 10G MAC 4:1 Mux + Linksec Fabric ASIC 2 Layer 3 Layer 2 Forwarding LinkSec decryption 1 st stage ingress port QoS Module 1 Fabric ASIC ACL/QoS/ NetFlow lookups L2-only SMAC/DMAC lookup L2 SMAC/ DMAC lookups Return result Layer 3 Layer 2 Forwarding Module 2 Transmit packet on wire Egress port QoS Fabric ASIC Fabric ASIC VOQs Replication 10G MAC Linksec e2/1 Receive from fabric Return buffer credit 11 Submit packet headers for egress L2 lookup 13 LinkSec encryption 16
35 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 36
36 IP Forwarding Nexus 7000 decouples control plane and data plane Forwarding tables built on control plane using routing protocols or static configuration OSPF, EIGRP, IS-IS, RIP, BGP for dynamic routing Tables downloaded to forwarding engine hardware for data plane forwarding 37
37 IP Forwarding Architecture Routing protocol processes learn routing information from neighbors IPv4 and IPv6 unicast RIBs calculate routing/next-hop information Unicast Forwarding Distribution Manager (UFDM) interfaces between URIBs on supervisor and IP FIB on I/O modules IP FIB process programs forwarding engine hardware on I/O modules FIB TCAM contains IP prefixes Adjacency table contains next-hop information n7010# sh processes cpu egrep ospf PID PID Runtime(ms) Invoked usecs 1Sec Process ospf n7010# sh processes cpu egrep u.?rib u6rib urib n7010# sh processes cpu egrep ufdm ufdm module-9# sh processes cpu egrep fib ipfib module-9# Supervisor BGP OSPF ISIS RIP EIGRP URIB/U6RIB UFDM IP FIB IP FIB IP FIB Hardware Hardware Hardware I/O Module I/O Module I/O Module Hardware FIB TCAM ADJ Table 38
38 Hardware IP Forwarding Process FIB TCAM lookup based on destination prefix (longest-match) FIB hit returns adjacency, adjacency contains rewrite information (next-hop) Pipelined forwarding engine architecture also performs ACL, QoS, and NetFlow lookups, affecting final forwarding result 39
39 IPv4 FIB TCAM Lookup HIT! Generate Lookup Key xx xx xx xx xx xx xx xx FIB TCAM Generate TCAM lookup key (destination IP address) Compare lookup key Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Index, # next-hops Hit in FIB returns result in FIB DRAM Index, # next-hops FIB DRAM Ingress unicast IPv4 packet header Load-Sharing Hash # nexthops Flow Data Adj Index Adjacency index identifies ADJ block Offset Hash selects exact next hop entry Forwarding Next-hop 1 (IF, MAC) Next-hop 2 (IF, MAC) Next-hop 3 (IF, MAC) Next-hop 4 (IF, MAC) Next-hop 5 (IF, MAC) Next-hop 6 (IF, MAC) Next-hop 7 (IF, MAC) Adjacency Table Return lookup result Result 41
40 Routing vs. Forwarding Routing information refers to unicast RIB contents in supervisor control plane Forwarding information refers to FIB contents at I/O module 42
41 Displaying Routing and Forwarding Information show routing [ipv4 ipv6] [<prefix>] [vrf <vrf>] Displays software routing (URIB) information Can also use traditional show ip route command show forwarding [ipv4 ipv6] route module <mod> [vrf <vrf>] Displays hardware forwarding (FIB) information on permodule basis show forwarding adjacency module <mod> Displays hardware adjacency table information on per-module basis 43
42 Displaying Routing and Forwarding Information (Cont.) n7010# sh routing ipv /24 IP Route Table for VRF "default" /24, 1 ucast next-hops, 0 mcast next-hops *via , Ethernet9/2, [110/5], 00:02:30, ospf-1, type-1 n7010# show forwarding ipv4 route /24 module 9 IPv4 routes for table default/base Prefix Next-hop Interface / Ethernet9/2 n7010# show forwarding adjacency module 9 IPv4 adjacency information, adjacency count 1 next-hop rewrite info interface
43 ECMP Load Sharing Up to 16 hardware load-sharing paths per prefix Use maximum-paths command in routing protocols to control number of load-sharing paths Load-sharing is per-ip flow or per-packet Use caution with per-packet load-balancing! Configure load-sharing hash options with global ip load-sharing command: Source and Destination IP addresses Source and Destination IP addresses plus L4 ports (default) Destination IP address and L4 port /16 A B Additional randomized number added to hash prevents polarization Automatically generated or user configurable value Configure per-packet load-sharing with interface ip load-sharing per-packet command Ingress interface determines if load-sharing is per-flow or per-packet! /16 via Rtr-A via Rtr-B 45
44 ECMP Prefix Entry Example n7010# sh routing ipv IP Route Table for VRF "default" /16, 2 ucast next-hops, 0 mcast next-hops *via , Ethernet9/1, [110/5], 00:03:33, ospf-1, inter *via , Ethernet9/2, [110/5], 00:00:13, ospf-1, inter n7010# sh forwarding ipv4 route module 9 IPv4 routes for table default/base Prefix Next-hop Interface / Ethernet9/ Ethernet9/2 n7010# 46
45 Identifying the ECMP Path for a Flow show routing [ipv4 ipv6] hash <sip> <dip> [<sport> <dport>] [vrf <vrf>] n7010# sh routing hash Load-share parameters used for software forwarding: load-share type: 1 Randomizing seed (network order): 0xebae8b9a Hash for VRF "default" Hashing to path * (hash: 0x29), for route: /16, 2 ucast next-hops, 0 mcast next-hops n7010# *via , Ethernet9/1, [110/5], 00:14:18, ospf-1, inter *via , Ethernet9/2, [110/5], 00:10:58, ospf-1, inter Same hash algorithm applies to both hardware and software forwarding 47
46 L3 Packet Flow HDR = Packet Headers DATA = Packet Data CTRL = Internal Signaling Credit grant for fabric access 9 Supervisor Central Arbiter Return credit to pool 12 Fabric Module 1 Fabric Module 2 Fabric Module 3 VOQ arbitration and queuing 8 Submit packet headers for lookup 2nd stage ingress port QoS Receive packet from wire 1 Transmit to fabric 4 3 e1/1 10 Fabric ASIC VOQs Replication 10G MAC 4:1 Mux + Linksec Fabric ASIC 2 Layer 3 Layer 2 Forwarding 6 LinkSec decryption 1st stage ingress port QoS Module 1 Fabric ASIC L3 FIB/ADJ lookup Ingress and egress ACL/QoS/ NetFlow lookups L2-only SMAC/DMAC lookup L2 ingress and egress SMAC/ DMAC lookups Return result 7 Layer 3 Layer 2 Forwarding Module 2 Transmit packet on wire Egress port QoS Fabric ASIC Fabric ASIC VOQs Replication 10G MAC Linksec e2/1 Receive from fabric Return buffer credit 11 Submit packet headers for egress L2 lookup LinkSec encryption
47 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 49
48 IP Multicast Forwarding Forwarding tables built on control plane using multicast protocols PIM-SM, PIM-SSM, PIM-Bidir, IGMP, MLD Tables downloaded to: Forwarding engine hardware for data plane forwarding Replication engines for data plane packet replication 50
49 IP Multicast Forwarding Architecture Multicast routing processes learn routing information from neighbors/hosts IPv4 and IPv6 multicast RIBs calculate multicast routing/rp/rpf/oil information Multicast Forwarding Distribution Manager (MFDM) interfaces between MRIBs on supervisor and IP FIB on I/O modules IP FIB process programs hardware: FIB TCAM Adjacency table Multicast Expansion Table (MET) n7010# sh processes cpu egrep pim igmp PID PID Runtime(ms) Invoked usecs 1Sec Process pim igmp n7010# sh processes cpu egrep m.?rib mrib m6rib n7010# sh processes cpu egrep mfdm mfdm Supervisor PIM IGMP PIM6 ICMP6 BGP MSDP MRIB/M6RIB MFDM IP FIB IP FIB IP FIB Hardware Hardware Hardware I/O Module I/O Module I/O Module Hardware MET FIB TCAM ADJ Table module-9# sh processes cpu egrep fib ipfib module-9# 51
50 Hardware Programming IP FIB process on I/O modules programs hardware: FIB TCAM Part of Layer 3 ASIC on forwarding engine Consists of (S,G) and (*,G) entries as well as RPF interface Adjacency Table (ADJ) Part of Layer 3 ASIC on forwarding engine Contains MET indexes Multicast Expansion Table (MET) Part of replication engine ASIC on I/O modules Contains output interface lists (OILs), i.e., lists of interfaces requiring replication 52 52
51 Ingress multicast packet header Compare lookup key Multicast FIB TCAM Lookup HIT! Generate Lookup Key , , , , , , FIB TCAM Hit in FIB returns result in FIB DRAM Generate TCAM lookup key (source and group IP address) RPF, ADJ Index RPF, ADJ Index RPF, ADJ Index RPF, ADJ Index RPF, ADJ Index FIB DRAM Adj Index Identifies multicast adjacency entry Forwarding MET Index MET Index MET Index MET Index MET Index Adjacency Table Result Return lookup result Replication for each OIF in MET block Replication Replicate 53 OIFs OIFs OIFs OIFs MET MET index used to find OIFs for replication
52 Displaying Multicast Routing and Forwarding Information show routing [ipv4 ipv6] multicast [vrf <vrf>] [<source-ip>] [<group-ip>] [summary] Displays software multicast routing (MRIB) information Can also use traditional show ip mroute command show forwarding [ipv4 ipv6] multicast route [source <ip>] [group <ip>] [vrf <vrf>] module <mod> Displays hardware multicast forwarding (FIB) information on per-module basis 55
53 Displaying Multicast Routing and Forwarding Information (Cont) n7010# sh routing multicast IP Multicast Routing Table for VRF "default" ( /32, /32), uptime: 00:40:31, ip mrib pim Incoming interface: Ethernet9/1, RPF nbr: , internal Outgoing interface list: (count: 2) Ethernet9/17, uptime: 00:05:57, mrib Ethernet9/2, uptime: 00:06:12, mrib n7010# sh routing multicast summary IP Multicast Routing Table for VRF "default" Total number of routes: 202 Total number of (*,G) routes: 1 Total number of (S,G) routes: 200 Total number of (*,G-prefix) routes: 1 Group count: 1, average sources per group: Group: /32, Source count: 200 Source packets bytes aps pps bit-rate oifs (*,G) bps mbps mbps mbps 2 < > 56
54 Displaying Multicast Routing and Forwarding Information (Cont.) n7010# sh forwarding ipv4 multicast route group source module 9 ( /32, /32), RPF Interface: Ethernet9/1, flags: Received Packets: Bytes: Number of Outgoing Interfaces: 2 Outgoing Interface List Index: 15 Ethernet9/2 Outgoing Packets: Bytes: Ethernet9/17 Outgoing Packets: Bytes: n7010# 57
55 Egress Replication Distributes multicast replication load among replication engines of all I/O modules with OIFs Input packets get lookup on ingress forwarding engine For OIFs on ingress module, ingress replication engine performs the replication For OIFs on other modules, ingress replication engine replicates a single copy of packet over fabric to those egress modules Each egress forwarding engine performs lookup to drive replication Replication engine on egress module performs replication for local OIFs Module 1 Fabric Module Fabric ASIC Fabric ASIC Fabric ASIC Fabric ASIC Fabric ASIC Replication 58 Local OIFs MET IIF Replication Replication Local OIFs Local OIF MET MET Fabric Copy Replication Local OIFs MET
56 L3 Multicast Packet Flow HDR = Packet Headers DATA = Packet Data Fabric Module 1 Fabric Module 2 Fabric Module 3 VOQ queuing 10 Transmit multicast fabric distribution packet Submit packet headers for lookup 2nd stage ingress port QoS Receive packet from wire 1 Transmit to fabric Fabric ASIC Layer 3 VOQs 15 VOQs 9 Layer 2 Layer 2 delivery e1/1 11 Replication 10G MAC 4:1 Mux + Linksec Fabric ASIC Forwarding 8 6 Replicate for fabric delivery Module 1 LinkSec decryption 1st stage ingress port QoS Fabric ASIC L3 multicast FIB lookup Ingress ACL/QoS/ NetFlow lookups Egress ACL/QoS/ NetFlow lookups L2 ingress snooping lookup Return MET result L2 egress snooping lookup Layer 3 Forwarding 17 Module 2 Transmit packet on wire Egress port QoS Fabric ASIC Fabric ASIC Replication 10G MAC Linksec e2/1 Dequeue multicast distribution copy from fabric 12 Replicate for local OIF Submit packet headers for egress lookups LinkSec encryption
57 Unicast vs. Multicast on Fabric Fabric consists of two parallel fabric planes : Unicast traffic Centrally arbitrated Round-robin load balanced over available fabric channels Multicast traffic Locally arbitrated Load balanced over available fabric channels using hash 60
58 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 61
59 Security ACLs Enforce security policies based on Layer 2, Layer 3, and Layer 4 information Classification TCAM (CL TCAM) provides ACL lookups in forwarding engine 64K hardware entries Router ACL (RACL) Enforced for all traffic crossing a Layer 3 interface in a specified direction IPv4, ARP RACLs supported VLAN ACLs (VACLs) Enforced for all traffic in the VLAN IPv4, MAC VACLs supported Port ACLs (PACLs) Enforced for all traffic input on a Layer 2 interface IPv4, MAC PACLs supported 62 62
60 ACL Architecture ACL manager receives policy via configuration ACL manager distributes policies to ACL/QoS Clients on I/O modules Supervisor CLI XML ACL Manager Clients perform ACL merge and program ACEs in Classification (CL) TCAM in forwarding engines ACL/QoS-C Hardware I/O Module ACL/QoS-C Hardware I/O Module ACL/QoS-C Hardware I/O Module n7010# sh processes cpu egrep aclmgr PID PID Runtime(ms) Invoked usecs 1Sec Process aclmgr module-9# sh processes cpu egrep aclqos aclqos module-9# Hardware CL TCAM 63
61 ACL CL TCAM Lookup Packet header: SIP: DIP: Protocol: TCP SPORT: DPORT: 80 Generate Lookup Key Generate TCAM lookup key (source/dest IPs, protocol, L4 ports, etc.) SIP DIP Protocol SPORT DPORT Security ACL ip access-list example permit ip any host deny ip any host deny ip any host permit tcp any any eq 22 deny tcp any any eq 23 deny udp any any eq 514 permit tcp any any eq 80 permit udp any any eq 161 Compare lookup key C xxxxxxx xx xx xxx xxx xxx xxx xxxxxxx xx xxx xxx xxxxxxx xx xxx xxx Forwarding Permit Deny Deny X= Mask xxxxxxx xxxxxxx 06 xxx xxxxxxx xxxxxxx 06 xxx 0017 xxxxxxx xxxxxxx 11 xxx 0202 HIT! xxxxxxx xxxxxxx 06 xxx 0050 xxxxxxx xxxxxxx 11 xxx 00A1 CL TCAM Hit in CL TCAM returns result in CL SRAM Permit Permit Permit CL SRAM Result Return lookup result Result affects final packet handling 64 Deny Deny
62 Displaying Classification Resources show hardware access-list resource utilization module <mod> n7010# sh hardware access-list resource utilization module 9 Hardware Modules Used Free Percent Utilization Tcam 0, Bank Tcam 0, Bank Tcam 1, Bank Tcam 1, Bank LOU Both LOU Operands 0 Single LOU Operands 2 TCP Flags Protocol CAM Mac Etype/Proto CAM Non L4op labels, Tcam Non L4op labels, Tcam L4 op labels, Tcam L4 op labels, Tcam n7010# 65
63 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 68
64 Quality of Service Comprehensive LAN QoS feature set Ingress and egress queuing and scheduling Applied in I/O module port ASICs Ingress and egress mutation, classification, marking, policing Applied in I/O module forwarding engines All configuration through Modular QoS CLI (MQC) All QoS features applied using class-maps/policymaps/service-policies 69
65 QoS Architecture QoS manager receives policy via configuration QoS manager distributes policies to ACL/QoS Clients on I/O modules Supervisor CLI XML QoS Manager Clients perform ACL merge and program hardware: ACEs in Classification (CL) TCAM in forwarding engines ACL/QoS-C Hardware ACL/QoS-C Hardware ACL/QoS-C Hardware Queuing policies in I/O module port ASICs I/O Module I/O Module I/O Module n7010# sh processes cpu egrep qos PID PID Runtime(ms) Invoked usecs 1Sec Process ipqosmgr module-9# sh processes cpu egrep aclqos aclqos module-9# Hardware CL TCAM I/O Module ASICs 70
66 Port QoS 8-Port 10G Module Buffers 96MB ingress per port 80MB egress per port Queue Structure 8q2t ingress 1p7q4t egress 71 71
67 8-Port 10G Module Buffering Ingress Replication q2t Port 1 96MB Port ASIC Port 1 80MB p7q4t 1 Egress 72
68 Port QoS 32-Port 10G Module Buffers Ingress (two-stage ingress buffering) Egress Dedicated mode: 1MB per port + 65MB per port Shared mode: 1MB per port + 65MB per port group Dedicated mode: 80MB per port Shared mode: 80MB per port-group Queue Structure 8q2t + 2q1t ingress 1p7q4t egress 73 73
69 32-Port 10G Module Buffering Shared Mode Ingress Replication (Fixed) 1 2 2q1t Ports 1,3,5,7 65MB Port ASIC Port 1,3,5,7 80MB p7q4t q2t Port 1 1MB Port 5 1MB Port 3 1MB Port 7 1MB 4:1 Mux 1,3,5,7 Port Group Egress 74
70 32-Port 10G Module Buffering Dedicated Mode Ingress Replication (Fixed) 1 2 2q1t Port 1 65MB Port ASIC Port 1 80MB p7q4t q2t Port 1 1MB 4:1 Mux 1,3,5,7 Port Group Egress 75
71 Port QoS 48-Port 1G Modules Buffers 7.56MB ingress per port 6.15MB egress per port Queue Structure 2q4t ingress 1p3q4t egress 76 76
72 48-Port 1G Modules Buffering Ingress 1 2 2q4t Port MB Port Port MB 7.6MB Port 1 7.6MB Port MB Port Port MB 7.6MB Port 2 7.6MB Port MB Port Port MB 7.6MB Port 3 7.6MB Replication Port ASIC 1-12 Port MB Port Port MB 6.2MB Port 1 6.2MB Port MB Port Port MB 6.2MB Port 2 6.2MB Port MB Port Port MB 6.2MB Port 3 6.2MB p3q4t Egress 77
73 Marking and Policing Classification uses CL TCAM in forwarding engine to match traffic After classification, traffic can be marked or policed Marking policies statically set QoS values for each class Policing performs markdown and/or policing (drop) Policers use classic token-bucket scheme Uses Layer 2 frame size when determining rate Note: policing performed on per-forwarding engine basis Shared interfaces (such as SVI/EtherChannel) and egress policies could be policed at <policing rate> * <number of forwarding engines> 78
74 QoS CL TCAM Lookup Packet header: SIP: DIP: Protocol: TCP SPORT: DPORT: 80 Compare lookup key HIT! Generate Lookup Key Generate TCAM lookup key (source/dest IPs, protocol, L4 ports, etc.) C xxxxxxx xx xx xx xxx xxx xxxxxxx xx xx xxx xxx xx xxxxxxx xxx xxx xx xxxxxxx 06 xxx xxx xxxxxxx xx 06 xxx 0017 CL TCAM SIP DIP Protocol SPORT DPORT Hit in CL TCAM returns result in CL SRAM ip access-list police permit ip any /24 permit ip any /24 ip access-list remark-dscp-32 permit udp /24 any ip access-list remark-dscp-40 permit tcp /24 any ip access-list remark-prec-3 permit tcp any /24 eq 23 Forwarding Policer ID 1 Policer ID 1 Remark DSCP 32 Remark DSCP 40 Remark IP Prec 3 CL SRAM QoS Classification ACLs Result Return lookup result Result affects final packet handling 79
75 Monitoring QoS Service Policies show policy-map interface [[<interface>] [type qos queuing]] brief] n7010# show policy-map interface e9/1 Global statistics status : Ethernet9/1 enabled Service-policy (qos) input: policy statistics status: mark enabled Class-map (qos): udp-mcast (match-all) packets Match: access-group multicast set dscp cs4 Class-map (qos): udp (match-all) packets Match: access-group other-udp police cir 2 mbps bc 1000 bytes pir 4 mbps be 1000 bytes conformed bytes, bps action: transmit exceeded bytes, bps action: set dscp dscp table cir-markdown-map violated bytes, bps action: drop n7010# 80
76 Agenda Chassis Architecture Supervisor Architecture I/O Module Architecture Forwarding Architecture Fabric Architecture Layer 2 Forwarding IP Forwarding IP Multicast Forwarding ACLs QoS NetFlow 81
77 NetFlow NetFlow table is 512K entries (490K effective), shared between ingress/egress NetFlow Hardware NetFlow entry creation CPU not involved in NetFlow entry creation/update All modules have independent NetFlow table Full and sampled NetFlow supported by hardware 82
78 NetFlow Architecture NetFlow manager receives configuration via CLI/XML NetFlow manager distributes configuration to NetFlow-Clients on I/O modules NetFlow-Clients apply policy to hardware n7010# sh processes cpu egrep nfm PID PID Runtime(ms) Invoked usecs 1Sec Process nfm module-9# sh processes cpu egrep nfp nfp module-9# Supervisor CLI XML NetFlow Manager NF-C NF-C NF-C Hardware Hardware Hardware I/O Module I/O Module I/O Module Hardware NF Table Hardware NetFlow Creation 83
79 Full vs. Sampled NetFlow NetFlow configured per-direction and per-interface Ingress and/or egress on per-interface basis Each interface can collect full or sampled flow data Full NetFlow: Accounts for every packet of every flow on interface, up to capacity of NetFlow table Sampled NetFlow: Accounts for M in N packets on interface, up to capacity of NetFlow table 86
80 Viewing NetFlow Records show hardware flow ip [detail] module <mod> n7010# sh hardware flow ip interface e9/1 module 9 D - Direction; IF - Intf/VLAN; L4 Info - Protocol:Source Port:Destination Port TCP Flags: Ack, Flush, Push, Reset, Syn, Urgent D IF SrcAddr DstAddr L4 Info PktCnt TCP Flags I 9/ :01024: A... S. I 9/ :01024: A... S. I 9/ :01024: S. < > n7010# sh hardware flow ip interface e9/1 detail module 9 D - Direction; IF - Intf/VLAN; L4 Info - Protocol:Source Port:Destination Port TCP Flags: Ack, Flush, Push, Reset, Syn, Urgent; FR - FRagment; FA - FastAging SID - Sampler/Policer ID; AP - Adjacency/RIT Pointer CRT - Creation Time; LUT - Last Used Time; NtAddr - NT Table Address D IF SrcAddr DstAddr L4 Info PktCnt TCP Flags ByteCnt TOS FR FA SID AP CRT LUT NtAddr I 9/ :01024: A... S N Y 0x000 0x x
81 NetFlow Data Export Generate NetFlow v5 or v9 export packets To NetFlow Collector I/O Module via Inband Fabric ASIC VOQs Supervisor LC CPU Aged Flows NetFlow Table Forwarding Hardware Flow Creation I/O Module Main CPU Switched EOBC LC CPU Aged Flows NetFlow Table Forwarding Hardware Flow Creation via mgmt0 Mgmt Enet To NetFlow Collector I/O Module LC CPU Aged Flows NetFlow Table Forwarding Hardware Flow Creation 90
82 Conclusion You should now have a thorough understanding of the Nexus 7000 switching architecture, I/O module design, packet flows, and key forwarding engine functions Any questions? 92 92
83 Q and A 94
84 Complete Your Online Session Evaluation Give us your feedback and you could win fabulous prizes. Winners announced daily. Receive 20 Passport points for each session evaluation you complete. Complete your session evaluation online now (open a browser through our wireless network to access our portal) or visit one of the Internet stations throughout the Convention Center. Don t forget to activate your Cisco Live Virtual account for access to all session material, communities, and on-demand and live activities throughout the year. Activate your account at the Cisco booth in the World of Solutions or visit 95
85
Cisco Nexus 7000 Hardware Architecture
Cisco Nexus 7000 Hardware Architecture Session Goal To provide you with a thorough understanding of the Cisco Nexus 7000 switching architecture, supervisor, fabric, and I/O module design, packet flows,
Cisco Nexus 7000 Switch Architecture
Cisco Nexus 7000 Switch Architecture BRKARC-3470 BRKARC-3470 2013 Cisco and/or its affiliates. All rights reserved. Cisco Public 2 Session Goal To provide a thorough understanding of the Cisco Nexus 7000
Configuring Denial of Service Protection
24 CHAPTER This chapter contains information on how to protect your system against Denial of Service (DoS) attacks. The information covered in this chapter is unique to the Catalyst 6500 series switches,
Implementing Cisco Data Center Unified Fabric Course DCUFI v5.0; 5 Days, Instructor-led
Implementing Cisco Data Center Unified Fabric Course DCUFI v5.0; 5 Days, Instructor-led Course Description The Implementing Cisco Data Center Unified Fabric (DCUFI) v5.0 is a five-day instructor-led training
Cisco 7600 Series Route Switch Processor 720
Cisco 7600 Series Route Switch Processor 720 Product Overview The Cisco 7600 Series Route Switch Processor 720 (RSP 720) is specifically designed to deliver high scalability, performance, and fast convergence
NetFlow/IPFIX Various Thoughts
NetFlow/IPFIX Various Thoughts Paul Aitken & Benoit Claise 3 rd NMRG Workshop on NetFlow/IPFIX Usage in Network Management, July 2010 1 B #1 Application Visibility Business Case NetFlow (L3/L4) DPI Application
NX-OS and Cisco Nexus Switching
NX-OS and Cisco Nexus Switching Next-Generation Data Center Architectures Kevin Corbin, CCIE No. 11577 Ron Fuller, CCIE No. 5851 David Jansen, CCIE No. 5952 Cisco Press 800 East 96th Street Indianapolis,
High Performance 10Gigabit Ethernet Switch
BDCOM S3900 Switch High Performance 10Gigabit Ethernet Switch BDCOM S3900 is a standard L3 congestion-less switch series, which are capable of multi-layer switching and wire-speed route forwarding. Its
Feature Support Cisco 2960 Cisco 2960S Brocade ICX 6450 Brocade ICX 6430 1 GE SFP, 2 10GE SFP+, 4 1GE SFP, 2 DUAL PURPOSE PORTS, 1GE OR SFP
Feature Support Cisco 2960 Cisco 2960S Brocade ICX 6450 Brocade ICX 6430 Uplinks 1 GE SFP, 2 10GE SFP+, 4 1GE SFP, 2 DUAL PURPOSE PORTS, 1GE OR SFP 40G Stack bandwidth via std 10G ports 2x10G* Fiber aggregation
20 GE + 4 GE Combo SFP + 2 10G Slots L3 Managed Stackable Switch
GTL-2691 Version: 1 Modules are to be ordered separately. 20 GE + 4 GE Combo SFP + 2 10G Slots L3 Managed Stackable Switch The LevelOne GEL-2691 is a Layer 3 Managed switch with 24 x 1000Base-T ports associated
Cisco Integrators Cisco Partners installing and implementing the Cisco Catalyst 6500 Series Switches
Implementing Cisco Catalyst 6500 Series Switches (RSCAT6K) Fast Lane is proud to be once again on the cutting edge with this intensive 3-day Authorized course on the latest features and functionality of
Configuring Flexible NetFlow
CHAPTER 62 Note Flexible NetFlow is only supported on Supervisor Engine 7-E, Supervisor Engine 7L-E, and Catalyst 4500X. Flow is defined as a unique set of key fields attributes, which might include fields
Ethernet Fabric Requirements for FCoE in the Data Center
Ethernet Fabric Requirements for FCoE in the Data Center Gary Lee Director of Product Marketing [email protected] February 2010 1 FCoE Market Overview FC networks are relatively high cost solutions
Configuring NetFlow-lite
CHAPTER 55 Note NetFlow-lite is only supported on Catalyst 4948E Ethernet Switch. This chapter describes how to configure NetFlow-lite on the Catalyst 4948E switch. NetFlow-lite provides traffic monitoring
Configuring Network Security with ACLs
CHAPTER 46 This chapter describes how to use access control lists (ACLs) to configure network security on the Catalyst 4500 series switches. The Catalyst 4500 series switch supports time-based ACLs. For
Cisco Nexus 7000 Series Supervisor Module
Cisco Nexus 7000 Series Supervisor Module The Cisco Nexus 7000 Series Supervisor Module (Figure 1) scales the control plane and data plane services for the Cisco Nexus 7000 Series system in scalable data
Cisco Nexus 5548P Switch Architecture
Cisco Nexus 5548P Switch Architecture What You Will Learn Cisco introduced Nexus 5000 Series Switches both as high-bandwidth, low-latency, access-layer switches for rack deployment and as the basis for
Fiber Channel Over Ethernet (FCoE)
Fiber Channel Over Ethernet (FCoE) Using Intel Ethernet Switch Family White Paper November, 2008 Legal INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR
Understanding Quality of Service on the Catalyst 6500 Switch
. White Paper Understanding Quality of Service on the Catalyst 6500 Switch Carl Solder CCIE #2416 Technical Marketing Engineer Internetworking Systems Business Unit Patrick Warichet CCIE #14218 Technical
Configuring MPLS QoS
CHAPTER 45 This chapter describes how to configure Multiprotocol Label Switching (MPLS) quality of service (QoS) in Cisco IOS Release 12.2SX. For complete syntax and usage information for the commands
Chapter 4 Rate Limiting
Chapter 4 Rate Limiting HP s rate limiting enables you to control the amount of bandwidth specific Ethernet traffic uses on specific interfaces, by limiting the amount of data the interface receives or
Chapter 7 Configuring Trunk Groups and Dynamic Link Aggregation
Chapter 7 Configuring Trunk Groups and Dynamic Link Aggregation This chapter describes how to configure trunk groups and 802.3ad link aggregation. Trunk groups are manually-configured aggregate links containing
Routing. Static Routing. Fairness. Adaptive Routing. Shortest Path First. Flooding, Flow routing. Distance Vector
CSPP 57130 Routing Static Routing Fairness Adaptive Routing Shortest Path First Flooding, Flow routing Distance Vector RIP Distance Vector Sometimes called Bellman-FOrd Original Arpanet, DECNet, Novell,
Configuring Control Plane Policing
CHAPTER 53 This chapter describes how to configure control plane policing (CoPP) with Cisco IOS Release 12.2SX. Note For complete syntax and usage information for the commands used in this chapter, see
Configuring Quality of Service
CHAPTER 37 QoS functionality on Supervisor Engine 6-E, Supervisor Engine 6L-E, Catalyst 49M, and Catalyst 4948E are equivalent. This chapter describes how to configure quality of service (QoS) by using
Catalyst 6500 Architecture
Catalyst 6500 Architecture 2 Session Goal To provide you with a thorough understanding of the Catalyst 6500 switching architecture, packet flow, forwarding engine functions, and key feature operations.
AlliedWare Plus OS How To. Configure QoS to prioritize SSH, Multicast, and VoIP Traffic. Introduction
AlliedWare Plus OS How To Configure QoS to prioritize SSH, Multicast, and VoIP Traffic Introduction This How To Note explains how to create a QoS policy that prioritizes SSH, multicast, and VoIP traffic
6/8/2011. Document ID: 12023. Contents. Introduction. Prerequisites. Requirements. Components Used. Conventions. Introduction
Page 1 of 9 Products & Services Understanding EtherChannel Load Balancing and Redundancy on Catalyst Switches Document ID: 12023 Contents Introduction Prerequisites Requirements Components Used Conventions
DCUFI - Implementing Cisco Data Center Unified Fabric v5.0
DCUFI - Implementing Cisco Data Center Unified Fabric v5.0 Eğitim Tipi ve Süresi: 5 Days VILT 5 Day VILT DCUFI - Implementing Cisco Data Center Unified Fabric v5.0 Learn to use NX-OS versions 6.1(2) and
Troubleshooting the Firewall Services Module
CHAPTER 25 This chapter describes how to troubleshoot the FWSM, and includes the following sections: Testing Your Configuration, page 25-1 Reloading the FWSM, page 25-6 Performing Password Recovery, page
Improving Quality of Service
Improving Quality of Service Using Dell PowerConnect 6024/6024F Switches Quality of service (QoS) mechanisms classify and prioritize network traffic to improve throughput. This article explains the basic
Cisco Catalyst 4500-X Series Switch Family
Product Bulletin Cisco Catalyst 4500-X Series Fixed 10 Gigabit Ethernet Aggregation Switch PB696811 Overview Cisco Catalyst 4500-X Series Switch (Figure 1) is a fixed aggregation switch that delivers best-in-class
IPV6 流 量 分 析 探 讨 北 京 大 学 计 算 中 心 周 昌 令
IPV6 流 量 分 析 探 讨 北 京 大 学 计 算 中 心 周 昌 令 1 内 容 流 量 分 析 简 介 IPv6 下 的 新 问 题 和 挑 战 协 议 格 式 变 更 用 户 行 为 特 征 变 更 安 全 问 题 演 化 流 量 导 出 手 段 变 化 设 备 参 考 配 置 流 量 工 具 总 结 2 流 量 分 析 简 介 流 量 分 析 目 标 who, what, where,
Migrate from Cisco Catalyst 6500 Series Switches to Cisco Nexus 9000 Series Switches
Migration Guide Migrate from Cisco Catalyst 6500 Series Switches to Cisco Nexus 9000 Series Switches Migration Guide November 2013 2013 Cisco and/or its affiliates. All rights reserved. This document is
- Multicast - Types of packets
1 Types of packets - Multicast - Three types of packets can exist on an IPv4 network: Unicast A packet sent from one host to only one other host. A hub will forward a unicast out all ports. If a switch
- Multiprotocol Label Switching -
1 - Multiprotocol Label Switching - Multiprotocol Label Switching Multiprotocol Label Switching (MPLS) is a Layer-2 switching technology. MPLS-enabled routers apply numerical labels to packets, and can
TP-LINK. JetStream 28-Port Gigabit Stackable L3 Managed Switch. Overview. Datasheet T3700G-28TQ. www.tp-link.com
TP-LINK JetStream 28-Port Gigabit Stackable L3 Managed Switch Overview TP-LINK s is an L3 managed switch designed to build a highly accessible, scalable, and robust network. The switch is equipped with
Layer 3 Network + Dedicated Internet Connectivity
Layer 3 Network + Dedicated Internet Connectivity Client: One of the IT Departments in a Northern State Customer's requirement: The customer wanted to establish CAN connectivity (Campus Area Network) for
- QoS and Queuing - Queuing Overview
1 Queuing Overview - QoS and Queuing - A queue is used to store traffic until it can be processed or serialized. Both switch and router interfaces have ingress (inbound) queues and egress (outbound) queues.
EdgeRouter Lite 3-Port Router. Datasheet. Model: ERLite-3. Sophisticated Routing Features. Advanced Security, Monitoring, and Management
EdgeRouter Lite 3-Port Router Model: ERLite-3 Sophisticated Routing Features Advanced Security, Monitoring, and Management High-Performance Gigabit Ports Advanced 3-Port Router Introducing the EdgeRouter
VXLAN: Scaling Data Center Capacity. White Paper
VXLAN: Scaling Data Center Capacity White Paper Virtual Extensible LAN (VXLAN) Overview This document provides an overview of how VXLAN works. It also provides criteria to help determine when and where
Configuring QoS. Finding Feature Information. Prerequisites for QoS
Finding Feature Information, page 1 Prerequisites for QoS, page 1 QoS Components, page 2 QoS Terminology, page 3 Information About QoS, page 3 Restrictions for QoS on Wired Targets, page 41 Restrictions
"Charting the Course...
Description "Charting the Course... Course Summary Interconnecting Cisco Networking Devices: Accelerated (CCNAX), is a course consisting of ICND1 and ICND2 content in its entirety, but with the content
Choosing Tap or SPAN for Data Center Monitoring
Choosing Tap or SPAN for Data Center Monitoring Technical Brief Key Points Taps are passive, silent, and deliver a perfect record of link traffic, but require additional hardware and create a point of
Configuring a Load-Balancing Scheme
Configuring a Load-Balancing Scheme Finding Feature Information Configuring a Load-Balancing Scheme Last Updated: August 15, 2011 This module contains information about Cisco Express Forwarding and describes
Configuring a Load-Balancing Scheme
This module contains information about Cisco Express Forwarding and describes the tasks for configuring a load-balancing scheme for Cisco Express Forwarding traffic. Load-balancing allows you to optimize
ALLNET ALL8944WMP Layer 2 Management 24 Port Giga PoE Current Sharing Switch
ALLNET ALL8944WMP Layer 2 Management 24 Port Giga PoE Current Sharing Switch 24-Port Giga PoE Current Sharing Pv6 and IPv4 Dual Protocol SNMP v1/v2c/v3 SSH version 2.0 Authentication TACACS+ Jumbo Frames
Configuring Quality of Service
CHAPTER 33 This chapter describes how to configure quality of service (QoS) with either automatic QoS (auto-qos) commands or standard QoS commands on a switch running Supervisor Engine 7-E. It describes
基 於 SDN 與 可 程 式 化 硬 體 架 構 之 雲 端 網 路 系 統 交 換 器
基 於 SDN 與 可 程 式 化 硬 體 架 構 之 雲 端 網 路 系 統 交 換 器 楊 竹 星 教 授 國 立 成 功 大 學 電 機 工 程 學 系 Outline Introduction OpenFlow NetFPGA OpenFlow Switch on NetFPGA Development Cases Conclusion 2 Introduction With the proposal
FWSM introduction Intro 5/1
Intro 5/0 Content: FWSM introduction Requirements for FWSM 3.2 How the Firewall Services Module Works with the Switch Using the MSFC Firewall Mode Overview Stateful Inspection Overview Security Context
CCT vs. CCENT Skill Set Comparison
Operation of IP Data Networks Recognize the purpose and functions of various network devices such as Routers, Switches, Bridges and Hubs Select the components required to meet a given network specification
INDIAN INSTITUTE OF TECHNOLOGY BOMBAY MATERIALS MANAGEMENT DIVISION : (+91 22) 2576 8800 (DR)
Item CORE SWITCH: 24 Ports Item Description 1)General requirements: Switch- modular operating system, non-blocking wire speed performance. Switch solution-capable of providing complete redundancy by using
Cisco IOS Flexible NetFlow Technology
Cisco IOS Flexible NetFlow Technology Last Updated: December 2008 The Challenge: The ability to characterize IP traffic and understand the origin, the traffic destination, the time of day, the application
Configuring Auto Policy-Based Routing
This chapter describes how to configure the Auto Policy-Based Routing (PBR) feature on the Citrix NetScaler Application Delivery Controller (ADC) appliance to ensure that return traffic from the real server
CS 78 Computer Networks. Internet Protocol (IP) our focus. The Network Layer. Interplay between routing and forwarding
CS 78 Computer Networks Internet Protocol (IP) Andrew T. Campbell [email protected] our focus What we will lean What s inside a router IP forwarding Internet Control Message Protocol (ICMP) IP
Configuring Denial of Service Protection
CHAPTER 52 This chapter contains information on how to protect your switch against Denial of Service (DoS) attacks. The information covered in this chapter is unique to Cisco IOS Release 12.2SX, and it
How To Learn Cisco Cisco Ios And Cisco Vlan
Interconnecting Cisco Networking Devices: Accelerated Course CCNAX v2.0; 5 Days, Instructor-led Course Description Interconnecting Cisco Networking Devices: Accelerated (CCNAX) v2.0 is a 60-hour instructor-led
Virtual PortChannels: Building Networks without Spanning Tree Protocol
. White Paper Virtual PortChannels: Building Networks without Spanning Tree Protocol What You Will Learn This document provides an in-depth look at Cisco's virtual PortChannel (vpc) technology, as developed
CCNA R&S: Introduction to Networks. Chapter 5: Ethernet
CCNA R&S: Introduction to Networks Chapter 5: Ethernet 5.0.1.1 Introduction The OSI physical layer provides the means to transport the bits that make up a data link layer frame across the network media.
Introduction to Cisco IOS Flexible NetFlow
Introduction to Cisco IOS Flexible NetFlow Last updated: September 2008 The next-generation in flow technology allowing optimization of the network infrastructure, reducing operation costs, improving capacity
Data Networking and Architecture. Delegates should have some basic knowledge of Internet Protocol and Data Networking principles.
Data Networking and Architecture The course focuses on theoretical principles and practical implementation of selected Data Networking protocols and standards. Physical network architecture is described
Datasheet. Advanced Network Routers. Models: ERPro-8, ER-8, ERPoe-5, ERLite-3. Sophisticated Routing Features
Advanced Network Routers Models: ERPro-8, ER-8, ERPoe-5, ERLite-3 Sophisticated Routing Features Advanced Security, Monitoring, and Management High-Performance Gigabit Ports Advanced Routing Technology
Procedure: You can find the problem sheet on Drive D: of the lab PCs. Part 1: Router & Switch
University of Jordan Faculty of Engineering & Technology Computer Engineering Department Computer Networks Laboratory 907528 Lab. 2 Network Devices & Packet Tracer Objectives 1. To become familiar with
Internet Protocols Fall 2005. Lectures 7-8 Andreas Terzis
Internet Protocols Fall 2005 Lectures 7-8 Andreas Terzis Outline Internet Protocol Service Model Fragmentation Addressing Original addressing scheme Subnetting CIDR Forwarding ICMP ARP Address Shortage
Management Software. Web Browser User s Guide AT-S106. For the AT-GS950/48 Gigabit Ethernet Smart Switch. Version 1.0.0. 613-001339 Rev.
Management Software AT-S106 Web Browser User s Guide For the AT-GS950/48 Gigabit Ethernet Smart Switch Version 1.0.0 613-001339 Rev. A Copyright 2010 Allied Telesis, Inc. All rights reserved. No part of
100-101: Interconnecting Cisco Networking Devices Part 1 v2.0 (ICND1)
100-101: Interconnecting Cisco Networking Devices Part 1 v2.0 (ICND1) Course Overview This course provides students with the knowledge and skills to implement and support a small switched and routed network.
- QoS Classification and Marking -
1 - QoS Classification and Marking - Classifying and Marking Traffic Conceptually, DiffServ QoS involves three steps: Traffic must be identified and then classified into groups. Traffic must be marked
TP-LINK. 24-Port 10/100Mbps + 4-Port Gigabit L2 Managed Switch. Overview. Datasheet TL-SL5428E. www.tp-link.com
TP-LINK 24-Port 10/100Mbps + 4-Port Gigabit L2 Managed Switch Overview TP-LINK JetStream L2 managed switch provides high performance, enterprise-level QoS, advanced security strategies and rich layer 2
Chapter 3. Enterprise Campus Network Design
Chapter 3 Enterprise Campus Network Design 1 Overview The network foundation hosting these technologies for an emerging enterprise should be efficient, highly available, scalable, and manageable. This
Johannesburg Stock Exchange. Colocation Network Configuration. Guidance Note
Johannesburg Stock Exchange Colocation Network Configuration Guidance Note Created by: Andre Botes Reviewed by: Quality Assured: Networks Manager Approved by: Clem Verwey Date: 18 August 2014 Version:
Steve Worrall Systems Engineer. [email protected]
Steve Worrall Systems Engineer [email protected] Agenda 100GbE Load sharing/link aggregation Foundry Direct Routing 2 100 Gigabit Ethernet 3 Current Status PAR approved, 802.3ba task force set up
Configuring QoS and Per Port Per VLAN QoS
27 CHAPTER This chapter describes how to configure quality of service (QoS) by using automatic QoS (auto-qos) commands or by using standard QoS commands on a Catalyst 45 series switch. It also describes
Configuring NetFlow Switching
Configuring NetFlow Switching This chapter describes how to configure NetFlow switching. For a complete description of NetFlow commands used in this chapter, refer to the Cisco IOS Switching s chapter
How To Switch In Sonicos Enhanced 5.7.7 (Sonicwall) On A 2400Mmi 2400Mm2 (Solarwall Nametra) (Soulwall 2400Mm1) (Network) (
You can read the recommendations in the user, the technical or the installation for SONICWALL SWITCHING NSA 2400MX IN SONICOS ENHANCED 5.7. You'll find the answers to all your questions on the SONICWALL
Cisco Performance Monitor Commands
1 action (policy react and policy inline react) Cisco Performance Monitor Commands action (policy react and policy inline react) To configure which applications which will receive an alarm or notification,
Configure Policy-based Routing
How To Note How To Configure Policy-based Routing Introduction Policy-based routing provides a means to route particular packets to their destination via a specific next-hop. Using policy-based routing
Configuring Static and Dynamic NAT Translation
This chapter contains the following sections: Network Address Translation Overview, page 1 Information About Static NAT, page 2 Dynamic NAT Overview, page 3 Timeout Mechanisms, page 4 NAT Inside and Outside
Five Pillars: Assessing the Cisco Catalyst 4948E for Data Center Service
Five Pillars: Assessing the Cisco Catalyst 4948E for Data Center Service August 2010 Page2 Contents Executive Summary... 3 Features and Manageability... 3 Fast Convergence With Flex Link... 4 Control Plane
Cisco - Catalyst 2950 Series Switches Quality of Service (QoS) FAQ
Page 1 of 8 Catalyst 2950 Series Switches Quality of Service (QoS) FAQ Document ID: 46523 TAC Notice: What's C han g i n g o n T A C We b H el p u s h el p y ou. Questions Introduction What is the software
WiNG 5.X How To. Policy Based Routing Cache Redirection. Part No. TME-05-2012-01 Rev. A
WiNG 5.X How To Policy Based Routing Cache Redirection Part No. TME-05-2012-01 Rev. A MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark
Sup720 Hardware Assisted Features
Sup720 Hardware Assisted Features 1 IPV6 Switching on Supervisor 720 IPV6 IPV6 SOFTWARE SOFTWARE FEATURES FEATURES IPV6 IPV6 HARDWARE HARDWARE FEATURES FEATURES 128K 128K FIB FIB entries entries IPV6 IPV6
Licensing Cisco NX-OS Software Features
Licensing Cisco NX-OS Software This publication contains information related to licensing types, options, procedures, installation, and management for the Cisco NX-OS software. Cisco Data Center Network
QoS Queuing on Cisco Nexus 1000V Class-Based Weighted Fair Queuing for Virtualized Data Centers and Cloud Environments
QoS Queuing on Cisco Nexus 1000V Class-Based Weighted Fair Queuing for Virtualized Data Centers and Cloud Environments Intended Audience Virtualization architects, network engineers or any administrator
Cisco 7600 Series Routers Cisco 7600 Series: Ethernet Services 20G Line Cards for Carrier Ethernet
. Data Sheet Cisco 7600 Series Routers Cisco 7600 Series: Ethernet Services 20G Line Cards for Carrier Ethernet The Cisco 7600 Series Ethernet Services 20 Gbps (ES20) Line Cards utilize an extensible design
Cisco FabricPath Technology and Design
Cisco Technology and Design 2 Agenda Introduction to Concepts Technology vs Trill Designs Conclusion 3 Introduction to By Francois Tallet 5 Why Layer 2 in the Data Centre? Some Applications / Protocols
Introducing Basic MPLS Concepts
Module 1-1 Introducing Basic MPLS Concepts 2004 Cisco Systems, Inc. All rights reserved. 1-1 Drawbacks of Traditional IP Routing Routing protocols are used to distribute Layer 3 routing information. Forwarding
Cisco Catalyst 2960-X Series
Q&A Cisco Catalyst 2960-X Series 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 1 of 18 Q&A Contents Product Overview... 3 Stacking... 6 Investment
Chapter 6 Configuring IP
Chapter 6 Configuring IP This chapter describes the Internet Protocol (IP) parameters on HP ProCurve routing switches and switches and how to configure them. After you add IP addresses and configure other
Network Layer: Network Layer and IP Protocol
1 Network Layer: Network Layer and IP Protocol Required reading: Garcia 7.3.3, 8.1, 8.2.1 CSE 3213, Winter 2010 Instructor: N. Vlajic 2 1. Introduction 2. Router Architecture 3. Network Layer Protocols
(VLAN feature configuration mode)
clear ip igmp snooping statistics clear ipv6 mld snooping statistics clear mls qos arp clear mls qos clear mls qos ip clear mls qos ipv6 clear mls qos mac clear mls qos mpls clear mls statistics debug
Cisco Certified Network Associate Exam. Operation of IP Data Networks. LAN Switching Technologies. IP addressing (IPv4 / IPv6)
Cisco Certified Network Associate Exam Exam Number 200-120 CCNA Associated Certifications CCNA Routing and Switching Operation of IP Data Networks Operation of IP Data Networks Recognize the purpose and
How To Balance On A Cisco Catalyst Switch With The Etherchannel On A Fast Ipv2 (Powerline) On A Microsoft Ipv1 (Powergen) On An Ipv3 (Powergadget) On Ipv4
Cisco - Understanding EtherChannel Load Balancing and Redundancy on Catalyst Switch...Page 1 of 10 Understanding EtherChannel Load Balancing and Redundancy on Catalyst Switches Document ID: 12023 Contents
Understanding and Configuring NAT Tech Note PAN-OS 4.1
Understanding and Configuring NAT Tech Note PAN-OS 4.1 Revision C 2012, Palo Alto Networks, Inc. www.paloaltonetworks.com Contents Overview... 3 Scope... 3 Design Consideration... 3 Software requirement...
Chapter 2 Quality of Service (QoS)
Chapter 2 Quality of Service (QoS) Software release 06.6.X provides the following enhancements to QoS on the HP 9304M, HP 9308M, and HP 6208M-SX routing switches. You can choose between a strict queuing
CCNA DATA CENTER BOOT CAMP: DCICN + DCICT
CCNA DATA CENTER BOOT CAMP: DCICN + DCICT COURSE OVERVIEW: In this accelerated course you will be introduced to the three primary technologies that are used in the Cisco data center. You will become familiar
20. Switched Local Area Networks
20. Switched Local Area Networks n Addressing in LANs (ARP) n Spanning tree algorithm n Forwarding in switched Ethernet LANs n Virtual LANs n Layer 3 switching n Datacenter networks John DeHart Based on
AutoQoS for Medianet
Appendix A AutoQoS for Medianet As of August 2010, an updated version of AutoQoS was released for the Catalyst 2960- G/S, 3560-G/E/X, and 3750-G/E/X family of switches (with IOS Release 12.2(55)SE). This
Interconnecting Cisco Network Devices 1 Course, Class Outline
www.etidaho.com (208) 327-0768 Interconnecting Cisco Network Devices 1 Course, Class Outline 5 Days Interconnecting Cisco Networking Devices, Part 1 (ICND1) v2.0 is a five-day, instructorled training course
Table of Contents. Cisco Configuring a Basic MPLS VPN
Table of Contents Configuring a Basic MPLS VPN...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...2 Related Products...2 Conventions...2 Configure...3 Network Diagram...3 Configuration
Configuring NetFlow. Information About NetFlow. NetFlow Overview. Send document comments to [email protected]. CHAPTER
CHAPTER 19 This chapter describes how to configure the NetFlow feature on Cisco NX-OS devices. This chapter includes the following sections: Information About NetFlow, page 19-1 Licensing Requirements
