TOOLS AND INSTRUMENTS

Transcription

1 ACID/MOISTURE TEST KITS TOTALTEST TEST TUBE Chemical crystals react with acid or moisture which may be present in system. DESCRIPTION TT1-002 All-in-Kit. (One Totaltest insturment, 2 Totaltest blue tubes, 2 Totaltest yellow tubes, Kits case) TT2-002 Standard pack of 6 replacement test tubes (yellow) THE TOTALTEST KIT INCLUDES: One Totaltest Instrument, Two Totaltest Test Tubes And a Totaltest Kit case. STD. PACK OF 6 KITS: TT1-001 REPLACEMENT TEST TUBE PACK INCLUDES: 5 test tubes Std. Pack of 6 replacement test tube packs REPAIR KIT INCLUDES: TT2-001 Replacement test tube pack includes: 5 test tubes Std. Pack of 6 replacement test tubes packs TT

2 ACID/MOISTURE TEST KITS REPAIR KIT INCLUDES: The first & only no-oil acid/moisture test Totaltest is the fast, easy and reliable way to test a refrigeration or air conditioning system for corrosive acid and acid-causing moisture. Because Totaltest is a self- contained test instrument which needs only a small sample of the gas in a system, you will never need to extract another oil sample again. In just 10 minutes you will know if there is corrosive acid or moisture present in the system. TOTALTEST Works As Easy As Insert a test tube in the instrument 2. Attach the TOTALTEST instrument to the unit. 3. In ten minutes, detach the TOTALTEST instrument, remove the disposable test tube and compare it to the chart on the package. TOTALTEST doesn t require a system shut-down. TOTALTEST works in 10 minutes or less. TOTALTEST reads acid and moisture in 1 test. TOTALTEST checks the whole system. TOTALTEST doesn t need an oil sample TOTALTEST tests R-22, R-12, R-500, R-502, and R-11 vapor. Use TOTALTEST to help prevent a premature refrigeration or air conditioning system breakdown. Use TOTALTEST to check a system after a compressor replacement. Use TOTALTEST as part of a maintenance contract, before you take on a new customer and as part of the agreement. WARNING: This product contains a chemical known to the state of California to cause cancer. 769

3 MANNIX INSTRUMENTS DELUXE DIGITAL POCKET THERMOMETER F/C Switch Protective Cover Auto Power Off ON/OFF Switch Data Hold Pocket Clip Drop Resistant Water Resistant 2.5 Probe Range: -40 to 300 F -40 to 150 C Battery: (1) LR44 Included HDT303K SCREW DRIVER/TESTER with RED GLOW LED Self-Test Function AC Voltage Test: Contact: 70 to 250 VAC Non-Contact: 70 to 600 VAC Continuity Test Polarity Test Microwave Oven Leakage Detector Fuse Continuity Check Locates a Broken Wire DIGITAL SLING PSYCHROMETER Much More Accurate Than Outdated Analog Technology No Water Necessary No Twirling No Reading Charts Saves Time and Labor Instrument Displays: Temperature Humidity Wet Bulb Dew Point MAN-SAM990DW TEMPERATURE/HUMIDITY PEN (THERMO-HYGROMETER) Color: Dark Grey Power Supply: One Button Cell Included (1 CR2032) Humidity Range: 5 to 95 RH Accuracy: 10 to 90 RH ±3% All Other Ranges ±5% Temperature: ±14 F to 122 F -10 C to 50 C Response Time: 80 Seconds Typical Simultaneous Display of Temperature and Humidity Memory (Min/Max) F/C Switch Pocket Sized ST600LED DIGITAL ANEMOMETER Simultaneous Display of Air Velocity and Temperature Recording Min., Max., and Average Measuring Average Air Velocity for Multi-points C and F Switchable Hold Auto Power Off RS232 Serial Output AIRFLOW RANGE RESOLUTION ACCURACY ft/min. 1 ±2% mph 0.1 ±2% m/sec. 0.1 ±2% km/hr. 0.1 ±2% TEMPERATURE -10 C to 50 C 0.1 ±0.6 C +14 F to 122 F 0.1 ±0.6 C PTH8708 DIGITAL HIGH TEMPERATURE THERMOMETER F/C Switch ClearButton Min/Max Function Plastic Sheath -14 F to 392 F (0 C to 200 C) DPT392F/C DCFM

4 MANNIX INSTRUMENTS CFM AIRFLOW METER Can read up to 8 multi-point readings Hard carrying case Single hand airflow measurement with recessed service grip F and C Switchable Auto power off RS232 output Specifications Air Flow 80 to 6900 ft/m (0.4 to 35 m/sec) Resolution 0.1 Accuracy ±3%, ±2 F (±1 C) Temperature +14 to 122 F (-10 to 50 C) DCFM8906 BACHARACH SLING PSYCHROMETER Sling-type psychrometer determines percent relative humidity Built-in side rule calculator correlates wet and dry bulb temperatures to relative humidity Dual range (high and low temperature) scales for better resolution Thermometers telescope into handle for protection when not in use Built-in water reservoir holds sufficient water for several hours of testing DESCRIPTION SCALE BAC Mercury Filled ( F) BAC Red Spirit Filled ( F) BAC Mercury Filled ( C) BAC Red Spirit Filled ( C) BACHARACH GAS PRESSURE MANOMETER BAC This accurate and portable manometer is easy to read. Whether you are measuring or adjusting the pressure in gas lines, the valuable manometer can be used for all types of gas burning appliances. Besides using this instrument to measure and adjust the inlet and manifold pressure, it can also be used to determine filter resistance, fan efficiency, air velocity and statistic pressures. BACHARACH OIL BURNER COMBUSTION KIT BAC Like the Gas Burner Combustion Kit featured above, this kit is one of the most economical means of testing for oil burner efficiency during installation and servicing. Included in this kit: Fire Efficiency Finder Carrying Case (large) Moisture Absorb. Material Sampling Hose Assembly Fyrite CO2 20% Filled Tempoint Therm.1000 (6 Stem) MZF Draft, +.05 to -.25 W True Spot Smoke Tester 771

5 BACHARACH MONOXER II CO ANALYZER WITH CASE BAC The continuous sampling instrument measures CO levels in combustion gas stack and ambient air levels quickly and accurately. Measures and displays low levels of CO between 0 and 2200 ppm (parts per million) in increments of 1 ppm Easy to hold with the multi-purpose strap Easy to read highly visible digital display with backlight Comes with probe and hose assembly for flu gas testing BACHARACH TRUE SPOT SMOKE TEST KIT BAC The True Spot smoke method has long been recognized as the accepted standard for oil burner smoke tests. The kit determines efficient combustion. The smoke test is an indispensable part of any oil burner service job as excess smoke is one of the most common causes of excessive fuel usage and expensive service requirements. BACHARACH FYRITE PRO 120 COMBUSTION ANALYZER WITCO BAC Increase your overall service productivity with the Fyrite Pro. Verify and adjust the efficiency of residential furnaces and appliances quickly and easily with the Fyrite Pro and all of these features: Simple to use. Turn unit on, select fuel, insert probe Each test can be recorded using an optional infrared printer (no wires) Hold key freezes the readings and transfers them to the infrared printer Tactile feedback from the instrument s keypad assures that the appropriate key has been activated Warranty offers worry free operation of instrument and sensors for up to two years after purchase A unique hand strap offers ease of handling Four alkaline batteries typically offer 24 hours of continuous operation Automatic power off ensure long battery life Optional protective rubber boot with magnet provides hands free operation Error message informs you of an instrument or sensor failure CE Certified 772

6 LEYBOLD INFICON D-TEK SELECT REFRIGERANT LEAK DETECTOR As the first accurate, reliable, highly sensitive, cordless refrigerant leak detector, the original D-TEK revolutionized the field. Now we have built on that technology leadership to create D-TEK Select. This nextgeneration refrigerant leak detector uses an innovative infrared absorption sensing cell that is extremely sensitive to all refrigerants and only refrigerants. FEATURES AT A GLANCE 0.10 oz (3 gm)/year sensitivity Equally sensitive to all refrigerants, including R-22, R- 134a, R- 404a, R-410a, R-507 (AZ-50) and all CFCs, HCFCs and HFCs 800-hour infrared cell life for low cost of ownership D-TEK Select maintains that sensitivity over time for consistent, accurate and reliable performance, even with the newer refrigerant blends. Best of all, the sensing cell lasts for approximately 800 hours almost 10 times longer than the original D-TEK sensor to lower your cost of ownership and improve job site productivity. Additional enhancements include a charging status indicator, sensor failure indication, and NiMH (nickel metal hydride) batteries. All in an easy-to-use unit with the quality and durability you ve come to expect from INFICON. Infrared cell does not weaken over time, so response remains consistent and accurate Infrared cell cannot be overloaded or poisoned by exposure to large amounts of refrigerant Selective to refrigerants only; will not react to smoke, humidity, and airflow or temperature changes High-efficiency air sampling pump provides quick response and quick clearing ( zeroing ) On-board diagnostics indicate charging status and warn of low battery or infrared cell failure NiMH power stick is environmentally friendly, won t corrode, and provides greater charging capacity Includes hard plastic case, NiMH power stick, 12V & 120V adapter/recharger, tip filters & infrared cell Made with pride in the USA Technical notes Specifications At the heart of the D-TEK Select Refrigerant Leak Base unit includes Detector is an infrared absorption filtometer. It consists of a sampling cell with an infrared source (or emitter) at one end, an infrared energy detector at the other end, and an optical filter in between them. Minimum sensitivity Like the visible light we see, infrared energy is part to R-12, R-134a, of the electromagnetic energy spectrum. Most R-404a materials absorb specific and known wavelengths of Controls infrared energy. The particular wavelengths of energy absorbed by a material are known as its Power absorption spectra. All refrigerants have similar Battery life absorption spectra in the range of Charging options micrometers. The infrared source (emitter) creates a highintensity stream of energy incorporating all Weight with power wavelengths in the infrared spectrum. The stream stick passes through the optical filter, which blocks all Probe wavelengths except those that refrigerants absorb. The filtered infrared energy strikes the detector and causes it to heat up. When refrigerant is drawn Recharger through the sampling cell by the internal pump, Operating some of the infrared energy is absorbed by the temperature refrigerant. This causes a decrease in the amount of Storage temperature infrared energy reaching the detector and a Case material corresponding drop in the detector s temperature, which triggers the D-TEK Select to alarm. This Certifications whole process takes a fraction of a second. By utilizing an optical filter with precise Warranty characteristics, INFICON has made D-TEK Select sensitive to all refrigerants, while eliminating false alarms. In addition, because there is no depletion of chemicals like in heated sensor detectors, the sensor will not be harmed by high refrigerant doses nor degrade over time. The detector recovery time is also immediate after the refrigerant clears the cell. Infrared cell, NiMH power stick, spare filters, 110VAC adapter with 6' cord, 12V adapter with cigarette lighter plug, and a hard plastic carrying case oz/yr (3 gm/yr) Power: on/off Sensitivity: high/low NiMH power stick 6.5 hours 110VAC adapter with 6' cord 12V adapter w/cigarette lighter plug 1.19 lb (0.54 kg) Chrome-plated flexible metal, approx. 17 (43 cm) long Built in 32 F to 122 F (0 C to 50 C) 14 F to 140 F (-10 C to 60 C) Self-extinguishing, per UL94HB CE Marking Power Safety and EMC. SAEJ year replacement 773

7 LEYBOLD INFICON D-TEK SELECT REFRIGERANT LEAK DETECTOR D-TEK Select / ACCESSORIES D-TEK Select G1 Headphones V power cord with cigarette lighter plug P1 120V adapter and cord NiMH power stick G1 Infrared cell G1 Tip/filter kit G1 Storage case G1 TEK-Mate The Affordable - Portable Leak Detector If you re looking for a moderately priced, hand-held leak detector with proven INFICON heated diode sensor technology TEK-Mate is the tool for you. Equal sensitivity to CFCs, HCFCs, and HFCs eliminates resetting or switching for different refrigerants. Automatically compensates for changing background contamination. And it s reliable, even under damp conditions. TEK-Mate uses a variable intensity audible alarm and a single flashing LED to help pinpoint leaks. It s dependable for long-lasting performance on two D-size batteries. SPECIFICATIONS Base unit includes Sensor, 2 D-size alkaline batteries, spare filters, and a hard plastic carrying case. 0.4 oz/yr. (11 g/yr.) 3-position slide switch off, low sensitivity, high sensitivity 2 D-size (1.5V) alkaline batteries Automatic Sensitivity to CFCs, HCFCs, HFCs Controls Power Contamination adjustment Weight with batteries 1.54 lb (700 g) Operating temperature range +32 F to 113 F 0 C to +45 C Probe Sampling system Certifications Warranty Chrome-plated flexible metal, approx. 17" (43 cm) long Positive displacement pump CE marking per Safety and EMC. SAEJ year replacement TEK-Mate / ACCESSORIES TEK-Mate Sensor Filter kit Storage case G G G P2 774

8 Wey-Tek The Affordable - Accurate Refrigerant Charging Scale 775

9 LEYBOLD INFICON Wey-Tek The Affordable - Accurate Refrigerant Charging Scale Wey-TEK & CHARGING MODULE / ACCESSORIES Wey-TEK Scale 110lbs. (50kg.) Wey-TEK Scale 220lbs. (100kg.) Charging Module HVAC&R Charging module automotive G G G G1A Wey-TEK Scale 110lbs. (50kg.) and charging module HVAC&R Wey-TEK Scale 110lbs. (50kg.) and charging module automotive Softsided briefcase for scale and charging module Softsided case for scale G G1A P P1 Protect INFICON Wey-Tek with this soft-sided carrying case, custom-made for either model of the Wey-Tek scale. This lightly padded sleeve keeps out dust and light moisture and protects the scale during transport or set-up at the job site. 776

10 LEYBOLD INFICON GAS-Mate Combustible Gas Leak Detector Now there s a high-quality, economical and portable gas leak detector. GAS-Mate is perfect for checking leaks in residential and commercial combustion appliances, such as natural gas or propane fired heating systems, or gas pipelines. GAS-Mate uses leading-edge technology to detect hydrocarbons and other gases with twice the sensitivity of competing models. As you can see, GAS-Mate is a precision instrument. With its rugged construction and high-impact case, GAS-Mate will stand up to plenty of real-world use. In fact, we double the standard one-year warranty time of other instruments with a full, two-year replacement warranty. FEATURES AT A GLANCE sensitive to 5 ppm methane (twice as sensitive as nearest competitor) also detects natural gas, propane, butane, cyclopentane, ethane, ethanol, isobutane and ammonia variable audio alarm and flashing LED indicate leak strength adjustable sensitivity helps pinpoint leaks fast auto zeroing for ignoring background gas levels in leak test area small sensor and probe tip permit leak checking in tighter places runs continuously for 60 hours on two alkaline D cells 2-year replacement warranty SPECIFICATIONS Base unit includes Sensitivity to methane Controls Power Battery life Probe Alarm indicators Dimensions Weight with batteries Operating temperature Storage temperature Certifications Sensor, two D-size alkaline batteries, and a hard plastic carrying case 5 ppm 3-position switch (off/high sensitivity/adjustable sensitivity); sensitivity slide switch 2 D-size (1.5V) alkaline batteries (use Duracell MN1300 to maintain intrinsically safe approval) 60 hours Chrome-plated flexible metal, approx. 17" (43 cm) long Variable flashing yellow LED and audible tick rate dependent on gas concentration 8.8" x 2" x 3" (22.4 cm x 5.1 cm x 7.6 cm) 1.54 lbs. (700 gm.) +32oF to +113oF (0oC to +45oC) +14oF to +140oF (-10oC to +60oC) CE UL913 Class I, Division I, Group A, B, C and D, Met GAS-Mate / ACCESSORIES GAS-Mate Sensor Storage case G G G1 777

11 Pilot Vacuum Gauge With its technologically advanced Pirani sensor, the INFICON Pilot Vacuum Gauge works throughout the entire evacuation process of air conditioning or refrigeration systems. Its easy-to-read digital display accurately shows the vacuum level at every stage in the evacuation cycle, from atmosphere down to one micron. Using the Pilot Vacuum Gauge, there s no waiting until the pumping process is well underway before you know whether your connections are tight. And that s the problem with vacuum gauges currently being used. If your gauge or pump is not properly connected to the system, you may never get down to the vacuum level required to get a reading on your gauge. Unlike these gauges, Pilot works at atmosphere, so you ll know right away if a vacuum is being pulled properly. SPECIFICATION Base unit Includes 9-volts,betterystorage case and manual Weight(With battery) 7.25 oz (0.2 kg) Power source 9v battery Refrigeration fitting 1/4" male flare Controls On/Off/Unit Selection Button Display units Microns, pascal, minibars Display range atm ( microns) to 1 micron Auto shut-off After 15 min: last reading displayed when restarted Accuracy < microns ±5%,> microns ±10% of reading Resolution(increments) microns: down to 1-micron Pascal: down to 1-Pa mbar:down to 0.01-mbar Operating temperature 0 to +50 C Storage temperature -10 to +60 C Maximum overpressure 150 psi (7.76x106 microns) Warranty 1 Year FEATURES AT A GLANCE Unlike competing units, it starts measuring right at the beginning of the evacuation cycle (even at full atmosphere). First and only HVAC/R vacuum gauge to use Pirani sensor technology for more precise readings. Competitively priced. Displays in microns, Pascal or millibars. Accurate readings from atmosphere (760,000 microns) down to one micron 1/4" stainless steel refrigeration fitting for easy access Low-battery indicator and automatic shut-off after 15 minutes Saves last reading with auto shut-off and displays it again at start-up Nine-volt battery operation One-year, over-the-counter warranty PILOT/ACCESSORIES Pilot Vacuum Gauge Carrying Case Vacuum Gauge Manifold G G G1 Can be used with any vacuum pump 778

12 WHISPER Ultrasonic Leak Detector INFICON Whisper Ultrasonic Leak Detector is ideal for detecting and locating sources of ultrasonic sound through the use of sophisticated electronic circuitry. Unaffected by audible noise, Whisper incorporates an Internal Noise Control allowing for use in extremely noisy environments, such as mechanical rooms, and around operating chillers. Because Whisper is designed to detect ultrasound at 40.5 khz, not even a murmur will escape detection. Use the optional transmitter for quick and accurate leak checking in walk-in coolers / freezers, wall and ceiling joints, around doors, windows, ducts, etc. APPLICATIONS AT A GLANCE Refrigerant Leaks Locating Worn Bearings Leaks in Pneumatic Control Systems Leaks in Natural Gas, LPG Leaks Leaks in Compressed Air Systems Leaks in Vacuum Systems Butane / Propane Storage Tank Leaks Line Set Leaks in Foundations / Walls Diagnosing Solenoid Operations Steam Traps Electrical Arcing SPECIFICATION Base unit includes Controls Power Weight with battery Operating temperature range Storage Temperature Warranty WHISPER/ACCESSORIES Whisper Ultrasonic Leak Detector G1 Transmitter G1 Headphones Storage case G1 9 V battery, rubber probe extension, headphones and storage case. On / Off switch Sensitivity: maximum / minimum knob One 9 volt alkaline battery 9 oz (0.25 kg) 32oF to +122oF; 0oC to +50oC 14oF to +140oF; -10oC to +60oC 2 years 779

13 SHARK Vacuum Pump The INFICON SHARK Vacuum Pump is designed for the Service Professional for quick deep evacuation, simplified maintenance/repair, and durability. SHARK is a two-stage rotary vane pump, with 6 cfm rated displacement for vacuum down to 15 microns. The pump, with features such as large oil capacity, gas ballast, internal oil pump, and fan, allow service technicians to make easier, more efficient service calls. The unique molded design of SHARK allows for easy carrying to the job while giving extraordinary durability. FEATURES AT A GLANCE Rotary Vane Two-Stage Pump - provides the ability to quickly pull a deep vacuum. Gas Ballast allows pumped water vapor to be exhausted to atmosphere instead of accumulating in oil reservoir without affecting the vacuum pump s performance. Anti-suck Back On Inlet prevents oil from entering system if a power disruption occurs. Large Oil Capacity offers higher cooling for longer component life and greater moisture pumping capability. Internal Oil Pump provides lubrication by throwing oil back on bearings and seal area increasing life expectancy of the vacuum pump. Replaceable One-Piece Cartridge - allows the HVAC/R professional to repair the vacuum pump without any hassles. Fan directs airflow for maximum surface area heat transfer keeping unit cooler. Bigger Bearings - 1" shaft supports cartridge and ensures pump lasts longer. Molded Plastic Housing unique design offering durability, ease of maintenance, and convenience. Oil Trapping Exhaust Filter minimizes oil loss through the exhaust system and prevents oil accumulation on pump. SPECIFICATIONS Base Unit Self-contained, 110 volt operation. Includes power cord, 1 qt. turbo oil T32, and user manual. Free Air Displacement 6 cfm (170 liter/minute) Vacuum Pump Design Two-stage rotary vane Motor 1/3 HP AC; 1700 RPM Oil Capacity 1.0 qts (0.95 liters) Weight 24 lb (10.89 kg) Dimensions (L x W x H) 19.6" x 11.8" x 7.1" (49.8 cm x 30.0 cm x cm) Warranty 1 year SHARK / ACCESSORIES SHARK VNR Turbo oil T32 (6 qts./case)

14 YOKOGAWA H10G REFRIGERANT LEAK DETECTOR Detect all CFC, HFC and HFC Refrigerants Manual balance/zero adjust control AC powered Switchable sensitivity 25 years of proven experience Alarm Sensitivity SW Position R-134a R-12 Small 0.5 oz/yr. 0.1 oz/yr. Medium 1.0 oz/yr. 0.5 oz/yr. Large 5.0 oz/yr. 3.o oz.yr. H10G01 H10PM REFRIGERANT LEAK DETECTOR Detect all CFC, HFC and HFC Refrigerants Manual or automatic auto zero balance control Unique sensor calibration system CEMark Pinpoints both small and large leaks Alarm Sensitivity SW Position R-134a R-12 Small 0.5 oz/yr. 0.1 oz/yr. Medium 1.0 oz/yr. 0.5 oz/yr. Large 5.0 oz/yr. 3.o oz.yr. H10PM-5 781

15 TEMPERATURE GUNS RAYNGER IP SERIES The Raynger IP models are hand-held, battery powered, non contact thermometers that plug directly into thermocouple meters with type J or type K inputs. IP-K IP-J RAYNGER ST SERIES Three models to choose from: Part Numbers ST20 Pro ST20x BUS ST60 ProPlus ST60x BUS ST80 ProPlus ST80x BUS DESCRIPTION -18 to 260 C (0 to 500 F) D:S = 4:1. Type K T/C output -18 to 260 C (0 to 500 F) D:S = 4:1. K4Type J T/C output ST20 Pro: Standard model with single laser sighting, and temperature range of -32 to 400 C (-25 to 750 F) ST60 ProPlus: Enhanced model with 8 point circular laser, high/low alarm, MAX, MIN, DIF, and AVG temperature settings, and a temperature range of 32 to 600 C (-25 to 1100 F). It also has adjustable emissivity, and a D : S ratio of 30 : 1. ST80 ProPlus: This model has all the features of the ST60 ProPlus, but with an expanded temperature range of -32 to 760 C (-25 to 1400 F) and optics that allows the user to measure smaller objects from farther away. This is great news for HVAC or facilities maintenance professionals who need to measure ceiling and duct temperatures from a distance Features include: 8 point Circular laser sightings (ST20 has single laser) 12 point data logging (ST60/80) RTD contact probe (ST60/80) Adjustable emissivity (ST60/80) Comfortable, ergonomic design Rubber overmold for durability and comfort Hard case Features ST20 ST60 ST80 Temperature -32 to 400 C -32 to 600 C -32 to 760 C Range: (-25 to 750 F) (-25 to 1100 F) (-25 to 1400 F) D:S (Distance to Spot size): 12:1 30:1 50:1 Laser Sighting: Single Spot 8 point 8 point Emissivity: pre-set to 0.95 adjustable adjustable Accuracy: ±1% ±1% ±1% Response Time: 500 msec 500 msec 500 msec MAX, MIN, DIF, and AVG Temperatures: MAX only All All Recall Last Reading: No Yes Yes HI/LO Alarm: No Yes Yes Protective Hard Case: Yes Yes Yes 782

16 TEMPERATURE GUNS RAYNGER MX SERIES Raynger MX models are handheld, battery powered, noncontact thermometers that are lightweight, accurate, and easy to use. All MX thermometers include Raytek s NEW innovative laser sighting a 16 point holographic image that outlines your target area, graphic displays on screen, adjustable emissivity (0.1 to 1.50), 1/10 resolution, and a distance to spot of 60:1. (At 60 feet from your target - you will measure the average temperatures of a 1 foot spot). All units include a hard plastic carry case. Innovative Features. On-board emissivity table Measures contact & IR temperature, simultaneously Customizable log location Bar graph charts last 10 temperature points Additional Features of MX Series Temperature Range -30 to 900 C (-25 to 1600 F) D:S (Distance to Spot Size) 60:1 Laser Sighting 16-point, class 2 Emissivity Adjustable Accuracy ±1% Response Time 250mSec C or F Selectable Protective Hard Case Included Data output RS-232 or 1 mv per degree MX2 DESCRIPTION Standard model, visible and audible HI alarm, 1% accuracy graphics displays, multiple displays at one time of maximum, minimum, and current temperatures, -30 to 900 C (-25 to 1600 F) Other models available. Contact your distributor. RAYTEK MINITEMP SERIES The Raytek MiniTemp is a hand-held, battery operated, non-contact thermometer that fits in your pocket. Temperature Range: D:S (Distance to Spot Size): Laser Sighting: Emissivity: Accuracy: Response Time: RAYMT2U -18 to 260 C L7(0 to 500 F) 6:1 No Pre-set to % 500 m Sec RAYMT4U -18 to 260 C L8(0 to 500 F) 6:1 Yes Pre-set to % 500 m Sec Powered by 9V alkaline or NiCd battery LCD Backlight Can display temperature in 0 C or 0 F Holds display for 7 seconds Raymtapk carrying case SWIRLJET OUTFITS For faster soldering and brazing Superhot flame from SWIRLJET tips will silver or alloy-braze pipe faster than a conventional flame More effective - flame concentrates heat on work where needed less waste Shorter wrap-around flame allows soldering of joints within an inch of walls or woodwork without damaging or discoloring Efficient - for use under all weather conditions; wind will not deflect high velocity flame Adjustable pressure with contents gauge and delivery pressure indicators on pressure adjustment knob Two outfits available - one for acetylene; one for FG-2, MAPP, or propane in refillable tanks POL POL APPLICATION For Acetylene B Tank For Refillable FG-2, MAPP, or Propane Tank 783

17 SWIRL AIR ACETYLENE KITS X-3B Kit (TUR ) Flexible kit brazes light/medium gauge steel. Components: AR-B (CGA 520) Regulator G-4Handle AH-12 Hose A-3Tip A-11Tip Soft solders to 3 (75mm) Silver brazes to 1-5/8 (40mm) B Tank Connection Instruction Manual X-4B Kit (TUR ) Higher capacity kit brazes medium/heavy gauge steel. Components: AR-B (CGA 520) Regulator G-4Handle AH-12 Hose A-5Tip A-14Tip Soft solders to 3-1/2 (90mm) Silver brazes to 2 (50mm) B Tank Connection Instruction Manual X-5B Kit (TUR ) Flexible lighter-duty kit. Components: AR-B (CGA 520) Regulator G-4Handle AH-12 Hose A-5Tip Soft solders to 1-1/2 (40mm) Silver brazes to 3/4 (20mm) B Tank Connection Instruction Manual X-5MC Kit (TUR ) Flexible lighter-duty kit. Components: AR-MC (CGA 200) Regulator G-4Handle AH-12 Hose A-5Tip Soft solders to 1-1/2 (40mm) Silver brazes to 3/4 (20mm) MC Tank Connection Instruction Manual X-6MC Kit (TUR ) All-purpose kit for work using MC tank. Components: AR-MC (CGA 200) Regulator G-4Handle AH-12 Hose A-3Tip & A-8Tip Soft solders to 2 (50mm) Silver brazes to 1 (30mm) MC Tank Connection Instruction Manual MSKA-1 Kit (TUR ) Features quieter operation. Components: AR-B (CGA 520) Regulator G-4Handle AH-12 Hose MSA-8 Tip Soft solders to 3 (75mm) Silver brazes to 3/4 (20mm) B Tank Connection Instruction Manual SWIRL AIR ACETYLENE KITS PL-5ADLX-MC Kit (TUR ) Components: AR-MC (CGA-200) Regulator G4 Handle AH-12Hose PL-5A Tip Soft Solders to 1-1/2 (40mm) Silver Brazes to 3/4 (20mm) MC Tank Connections Instruction Manual PL-5ADLX-B Kit (TUR ) (Not Shown) B PL-8ADLX-MC Kit (TUR ) Components: AR-MC (CGA-200) Regulator G4 Handle AH-12Hose PL-8A Tip Soft Solders to 2 (50mm) Silver Brazes to 1 (30mm) MC Tank Connections Instruction Manual PL-8ADLX-B Kit (TUR ) (Not Shown) B Tank Connection PL-12ADLX-B (TUR ) Components: AR-B (CGA-520) Regulator G4 Handle AH-12Hose PL-12A Tip Soft Solders to 3-1/2 (90mm) Silver Brazes to 2 (50mm) B Tank Connections Instruction Manual 784

18 SWIRL AIR ACETYLENE KITS PRO-LINE with valve forward handle. Components: Except for valve forward handle, kits use same components as PL rear valve kits shown above. Description: PLF-5A-DLX-MC PLF-5A-DLX-B Part No. TUR (Not Shown) PLF-8A-DLX-MC TUR PLF-8A-DLX-B (Not Shown) PLF-8A-DLX-MC PLF-8A-DLX-B SWIRL AIR ACETYLENE TIPS TUR TUR (Not Shown) TIP SIZE GAS FLOW COPPER TUBING SIZE CAPACITY REPLACEMENT TIP NO in psi ft3/hr (09 bar) m3/hr Soft Solder Soft Solder Silver Braze Silver Braze ORIFICE TIP ENDS in mm in mm MODEL A-2 1/ /8-1/ /8-1/ OR-A2 -- A-3 3/ / /8-1/ OR-A3 -- A-5 1/ /4-1-1/ /4-3/ OR-A5 -- A-8 5/ / OR-A8 -- A-11 7/ / /8-1-5/ OR-A11 -- A-14 1/ / OR-A14 -- PL-5A 3/ /4-1-1/ /4-3/ OR-A8 5A-TE PL-8A 5/ / ORPL-8A 8A-TE *Use with large tank only. NOTE: For air conditioning, add 1/8 for type L tubing. SWIRL AIR ACETYLENE TIPS TIP SIZE GAS FLOW COPPER TUBING SIZE CAPACITY REPLACEMENT TIP NO in psi ft3/hr (09 bar) m3/hr Soft Solder Soft Solder Silver Braze Silver Braze ORIFICE TIP ENDS in mm in mm MODEL A-32* 3/ / OR-A32 -- MSA-8 3/ / /4-3/ OR-A5 -- PL-3A 1/ / /8-1/ OR-A3 3A-TE PL-12A 3/ OR-T-6 12A-TE *These Models Require Two Heaters. 785

19 SWIRL AIR ACETYLENE COMPONENTS SA Sppy Adapter (TUR ) Screws into Sof-Flame or other threaded handles adapting it to the TurboTorch Quick Disconnect tips. Provides the advantages of Turbo Torch at lowest cost. PLF-A5 Pro-Line Handle (TUR ) Ergonomically designed handle with valve and quick disconnect. Fits all Proline and TurboTorch tips. A Size 3/8-24 Hose Connection. Acetylene Hose AH-12 (TUR ) AH-24 (TUR ) 3/16 I.D. with 3/8 24-thread LH nuts. Fits G4 and PLF-A Handle, AR-B (CGA-520) & AR-MC (CGA-200) regulators. AH-12, 12 ft. (3.6m) hose. TT-MC (TUR ) Heavy duty steel construction fits MC tank or MT-1 MAPP tank. Easy storage of tips, handle, hose and striker. G-4 TurboTorch Handle (TUR ) Ergonomically designed handle with valve and quick disconnect. Fits all Proline and TurboTorch tips. A size 3/8-24 Hose Connection. TT-150 (TUR ) Durable composite construction fits B tank. A heavy nylon belt can keep your outfit secure on scaffolds or in the truck. Large Handle HoseRack Accessory Holder Acetylene Regulators AR-B (TUR ) AR-MC (TUR ) Brass construction, adjustablewith contents gauge. AR-B (CGA-520), fits B tank & 3/8 24-thread LH hose nut. AR-MC (CGA-200) fits MC tank & 3/8 24-thread LH hose nut. 786

20 SOF-FLAME ACETYLENE KITS & TIPS WSF-3 Kit (TUR ) Kits now include gauge guard and cylinder wrench Components: AR-MC (CGA 200) Regulator WA-400 Handle AH-12 Hose S-4Tip Soft Solders to 1 (25mm) MC Tank Connection Instruction Manual WSF-4 Kit (TUR ) Components: AR-B (CGA 520) Regulator WA-400 Handle AH-12 Hose S-4Tip Soft Solders to 1 (25mm) B Tank Connection Instruction Manual WA-400 Handle (TUR ) A Size 3/8 24 LH Hose Threads, Interchangeable with brands of equipment Requires no tools for tip change Tips can be locked in any position Stainless steel ball valve for added durability Replaceable O-ring seal for safety Accepts Snappy Adapter S-1 (TUR ) SOFT SOLDERS OPERATING PRESSURE RANGE ACETYLENE CONSUMPTION RANGE MODEL NO in mm PSI BAR SCFH m3/hr REPLACEMENT ORIFICE MODEL S-1 1/16-1/ OR-SI S-2 1/8-3/ OR-A2 S-3 3/8-1/ OR-T3 S-4 1/ OR-A5 S-5 3/4-1-1/ OR-A11 S OR-A14 SWIRL PROPANE & MAPP KITS LP-1 Kit (TUR ) Kits now include gauge guard and cylinder wrench Components: R-LP Adjustable Regulator, CGA-510 H-4 Handle H-12Hose T-4Tip T-6Tip Soft solders to 6 (150mm) Silver brazes to 4 (100mm) Instruction Manual 787

21 SWIRL PROPANE & MAPP KITS LP-2 Kit (TUR ) Components: R-LP Adjustable Regulator, CGA-510 H-4 Handle H-12Hose T-3Tip T-5Tip Soft solders to 4 (100mm) Silver brazes to 2 (50mm) Instruction Manual LP-3 Kit (TUR ) Components: R-LP Adjustable Regulator, CGA-510 H-4 Handle H-12Hose T-4Tip Soft solders to 2-1/2 (60mm) Silver brazes to 1-1/4 (30mm) Instruction Manual NOTE: TurboTorch LP torches and Pro-Line torches operate on Propane, Propylene, MAPP, Apachi and HPG. TurboTorch/ Pro-line torches use the hotter high energy gases for maximum heat, and propane for economy where high heat is not necessary. SWIRL PROPANE & MAPP TIPS/COMPONENTS Turbo-Torch Tips Count on total performance from TurboTorch MAPP & Propane tips. Varying size tips help you get the job done - quick and easy! TIP NO TIP SIZE GAS FLOW COPPER TUBING SIZE CAPACITY PROPANE GAS COPPER TUBING SIZE CAPACITY MAPP GAS in psi psi lb/hr Soft Solder in Soft Solder mm Silver Braze in Silver Braze mm Soft Solder in Soft Solder mm Silver Braze in Silver Braze REPLACEMENT mm ORIFICE MODEL T-2 5/ /8-1/ /16-1/ /8-1/ /8-1/ OR-A2 T-3 7/ / /8-1/ /4-1-1/ /4-1/ OR-T3 T-4 1/ /4-1-1/ /4-3/ /4-2-1/ /4-1-1/ OR-A3 T-5 3/ /2-2-1/ /2-1-1/ / OR-A8 T / / / / OR-T6 788

22 SWIRL PROPANE & MAPP TIPS/COMPONENTS TT-B (TUR ) Heavy duty steel construction fits B tank. Storage for tips, hose, handle and striker. SWIRL PROPANE & MAPP KITS PRO-LINE WITH REAR VALVE HANDLE PL-3TDLX Kit (TUR ) Components: RL-P Regulator, CGA-510 H-4 Handle H-12Hose PL-3T Tip Soft Solders 1 (25mm) Silver Brazes 1/2 (12mm) Instruction Manual PL-4TDLX Kit (TUR ) Components: RL-P Regulator, CGA-510 H-4 Handle H-12Hose PL-4T Tip Soft Solders 1-1/2 (40mm) Silver Brazes 3/4 (20mm) Instruction Manual PL-5TDLX Kit (TUR ) Components: RL-P Regulator, CGA-510 H-4 Handle H-12Hose PL-5T Tip Soft Solders 2-1/2 (63mm) Silver Brazes 1-1/4 (31mm) Instruction Manual) PL-4T STD Kit (TUR ) Components: H-4Handle PL-4T Tip PRO-LINE Standard Kit. 789

23 SWIRL PROPANE & MAPP TIPS/COMPONENTS PRO-LINE PRO-LINE Tips Soldering & Brazing sizes based on Propane. Capacity larger on MAPP gas. TIP SIZE COPPER TUBING SIZE CAPACITY PROPANE GAS COPPER TUBING SIZE CAPACITY MAPP GAS AIR PROPANE REPLACEMENT TIP NO in mm Soft Solder in Soft Solder mm Silver Braze in Silver Braze mm Soft Solder in Soft Solder mm Silver Braze in Silver Braze psi psi lb/hr ORIFICE MODEL TIP ENDS PL-3T 3/ / /8-1/ /4-1-1/ /4-1/ OR-T-3 3T-TE PL-4T 7/ /4-1-1/ /4-3/ /4-2-1/ /4-1-1/ OR-PL4T 4T-TE PL-5T 5/ /2-2-1/ /2-1-1/ / OR-PL5T 5T-TE Total LP Hose H-12 (TUR ) H-24 (TUR ) 3/16 I.D. T Grade hose with 9/16 18 LH Thread. Fits H-4 handle, T-8 torch, R-LP adjustable LP regulator. H-12, 12 ft. (3.6m) hose H-24, 24 ft (7.3m) hose H-4 Handle (TUR ) Ergonomically designed handle with valve rear and quick disconnect. Fits all Proline and TurboTorch tips. B size 9/16-18 hose connection R-LP Regulator (TUR ) Brass regulator for use with MAPP, Propane and other LPG fuel gas. Adjustable to 60 psi. Fits standard POL valve & 9/16 18 LH hose nut. Not for use with Acetylene. R-LP-993 Regulator for British 993 Markets, Part No.TUR HAND TORCHES & COMPONENTS PROPANE AND MAPP GASES Torches are built with TurboTorch swirl combustion All models have 360 swivel tips Easy-to-clean orifice, replaceable tips Designed to operate with a tank of either MAPP or Propane gas Hand Torch line lets you choose the gas for silver brazing copper tubing, bronze brazing steel pipe, or soldering with water in the line. STK-99 Kit (TUR ) Components: STK-R Pressure Regulator CGA-600 ST-33Tip Easy to Change Orifice Swivels 360º Instruction Manual 790

24 HAND TORCHES & COMPONENTS STK-8B Kit (TUR ) Components: STK-R Pressure Regulator CGA-600 ST-3Tip L-1Striker Packed in Handy, Rugged Plastic Box Instruction Manual STK-9 Kit (TUR ) Components: STK-R Pressure Regulator CGA-600 ST-3Tip Easy to Change Orifice Swivels 360º Instruction Manual STK-1 Kit (TUR ) Components: STK-R Pressure Regulator CGA-600 ST-1Tip Easy to Change Orifice Swivels 360º Instruction Manual PROPANE & MAPP HAND TORCHES PROPANE AND MAPP GASES ST-33 Self-Igniting Tip Assembly Only (TUR ) Fits existing STK-9 and STK-99 torches 44TL-TE Self-Lighting Tip End (TUR ) Fits ST-33, STK-99 & TL-44 STK-R Regulator (TUR ) Adjustable pressure regulator CGA 600. Use with MAPP or Propane tanks. Fits ST tips and TS-12 hose. Hand Torch Tips COPPER TUBING SIZE CAPACITY MAPP GAS Silver Braze Silver Braze in mm. TIP NO Soft Solder Soft Solder mm ST-1 1/8-1/ /2-3/ STOR-1 ST-3 3/8-2-1/ /4-1-3/ STOR-3 ST-4 1-3/8-2-1/ /4-1-3/ STOR-3 ST-5 1/8-1/ /2-3/ STOR-1 REPLACEMENT ORIFICE MODEL 791

25 SELF-LIGHTING TORCHES & KITS PROPANE AND MAPP GASES TL-44 TurboLite Self-Lighting Torch (TUR TurboTorch swirl combustion technology Gives you the best burn in a self-lighting package. Flame tube swivels 180 for easy positioning. MAPP or Propane gas without changing the Orifice. Workplace-designed without exposed wires. Trigger Lock Performance equivalent to T-3 LP tip. Features: Replaceable tip-end Easy to clean orifice Heavy-duty piezo ignitor Machined rotor Wide lighting range Use with CGA 600, 1 lb. MAPP or Propane Tanks. Tank not included TLK-41 (TUR ) Allows remote operation with a 1lb. refillable cylinder TL-44Torch T Adapter TS-12Hose STK-R Regulator CGA-600 Use of TSR tank rack is recommended TLK-44 TurboLite Self-Lighting Torch Kit (TUR ) Components: TL-44 TORCH Plastic Carrying Case PRO-LINE Self-Lighting Ske Kit) (Does not include gas) The swirl combustion tip gives you the best burn and cuts brazing time by 30%. Flame tube swivels 360 for work at any angle. Push trigger ignition. Rugged brass regulator. Offered with either #3 or #4 size tip with replaceable tip. Runs cool, quietly and efficiently. Components: Self-Lighting Propane & MAPP Tip TSR Tank Rack with Retainer Ergonomically designed handle STK-R Regulator CGA ft. of Hose Model No. PS-3T Pro-Snake Kit Size 3 (TUR ) Model No. PS-4T Pro-Snake Kit Size 4 (TUR ) TS-1B Kit (TUR ) (Does not include gas) Makes easy work of soldering in hard-to-reach places. Soft solders up to 2-1/2 (60mm) and silver brazes up to 1-3/8 (35mm). Can be used with MAPP or Propane Components: ST-4Tip TSH Handle TS-12, 12 ft. (3.7m) Hose Assembly STK-R Regulator, CGA-600 MT-1 MAPP Tank TSR Tank Rack with Retainer Instruction Manual 792

26 SELF-LIGHTING TORCHES & KITS PROPANE AND MAPP GASES TP-10 Pencil Flame Propane Torch (TUR ) Solid brass construction for lasting durability Flame control valve for precise heat adjustments May be used with any 14.1 oz. propane tank Great for light application jobs: - Soldering - Thawing frozen pipes - Loosening rusty nuts & bolts - Heating - Light maintenance CUTTING & BRAZING EQUIPMENT CWK SERIES KITS A CONNECTIONS CWK-4 Kit (TUR ) Listed Components Components: FP Oxygen Regulator CGA FP Acetylene Regulator CGA FP Handle FP Cutting Attachment 2-W-J Nozzle with Mixer Cutting Tip Reverse Flow Check Valves P 3/16 x 12 1/2 ft. Twin Hose P Goggle Carrying Case & Instruction Booklet CWK-4T Kit (TUR ) Components: Same as CWK-4 Kit plus AC-MC & OX-20 Tanks CWK-5T Kit (TUR ) (not shown) SameasCWK-5Kitplus AC-MC&OX-20Tanks CWK-5 Kit (TUR ) Components: FP Oxygen Regulator CGA FP Acetylene Regulator CGA FP Handle 2-W-J & 4-W-J Nozzle with Mixer Reverse Flow Check Valves P 3/16 x 12 1/2 ft. Twin Hose P Goggle Carrying Case & Instruction Booklet 793

27 CUTTING & BRAZING EQUIPMENT CWK SERIES KITS A CONNECTIONS CWK-2T Kit (TUR ) Components: FP Oxygen Regulator CGA FP Acetylene Regulator CGA FP Handle FP Cutting Attachment Cutting Tip 0-W-J, 2-W-J and 4-W-J Nozzle with Mixer Reverse Flow Check Valves P 3/16 x 12 1/2 ft. Twin Hose Replacement Nozzles & Mixers for CWK Series MODEL NO TIP SIZE BRAZING CAPACITY FOR USED WITH THESE HANDLES CONFIGURATION COPPER TUBING TUR W-J-CS 000 1/8-1/2 (3-12mm) FP Complete w/nozzle Mixer TUR W-J-CS 00 1/8-3/4 (3-19mm) FP Complete w/nozzle Mixer TUR W-J-CS 0 1/4-1 (6-25mm) FP Complete w/nozzle Mixer TUR W-J-CS 1 1/4-1-1/4 (6-31mm) FP Complete w/nozzle Mixer TUR W-J-CS 2 1/2-1-1/2 (12-38mm) FP Complete w/nozzle Mixer Replacement Cutting Tips for CWK Series MODEL NO DESCRIPTION TIP SIZE CUTTING CAPACITY GAS SERVICE USED WITH THESE CUTTING ATTACHMENTS TUR CS to 1/4 (6mm) material Acetylene FP and FP TUR CS -- 0 to 1/2 (12mm) material Acetylene FP and FP TUR CS -- 1 to 3/4 (19mm) material Acetylene FP and FP TUR CS -- 2 to 1 (25mm) material Acetylene FP and FP TUR P Adapter Air/Acetylene Only, used on FP Handle *CS indicates clamshell package. CUTTING & BRAZING EQUIPMENT 100 SERIES KITS B CONNECTIONS FP Kit (TUR ) Components: FP Oxygen Regulator CGA FP Acetylene Regulator CGA FP Handle with Flash Arrestors FP Cutting Attachment P B to A Adapter 000-W-1, 0-W-1 & 2-W-1 Nozzles Cutting Tip P 3/16 A Size x 12 1/2 ft. Twin Hose P Goggles, L-1 Striker & Instruction Booklet Carrying Case FPT Kit (TUR ) Components: FP Oxygen Regulator CGA FP Acetylene Regulator CGA FP Handle with Flash Arrestors FP Cutting Attachment P B to A Adapter 000-W-1, 0-W-1 & 2-W-1 Nozzles Cutting Tip P 3/16 x 12 1/2 ft. Twin Hose P Goggles, L-1 Striker & Instruction Booklet Carrying Case AC-MC & OX-20 Tanks Included 794

28 CUTTING & BRAZING EQUIPMENT 100 SERIES KITS B CONNECTIONS FP Kit (TUR ) Components: FP Oxygen Regulator CGA FP Acetylene Regulator CGA FP Handle with Flash Arrestors FP Cutting Attachment P B to A Adapter 000-W-1, 0-W-1 & 2-W-1 Nozzles Cutting Tip P 3/16 A Size x 12 1/2 ft. Twin Hose P Goggles, L-1 Striker & Instruction Booklet Air/Gas Adapter A-5 AcetyleneTip Carrying Case Replacement Cutting Tips for 100 Series MODEL NO DESCRIPTION TIP SIZE CUTTING CAPACITY GAS SERVICE USED WITH THESE CUTTING ATTACHMENTS TUR CS to 1/4 (6mm) material Acetylene FP and FP TUR CS -- 0 to 1/2 (12mm) material Acetylene FP and FP TUR CS -- 1 to 3/4 (19mm) material Acetylene FP and FP TUR CS -- 2 to 1 (25mm) material Acetylene FP and FP TUR P Adapter Air/Acetylene Only, used on FP Handle *CS indicates clamshell package. Replacement Nozzles & Mixers for 100 Series MODEL NO TIP SIZE BRAZING CAPACITY FOR COPPER USED WITH THESE HANDLES CONFIGURATION TUBING TUR W-J-CS 000 1/8-1/2 (3-12mm) FP Complete w/nozzle Mixer TUR W-J-CS 00 1/8-3/4 (3-19mm) FP Complete w/nozzle Mixer TUR W-J-CS 0 1/4-1 (6-25mm) FP Complete w/nozzle Mixer TUR W-J-CS 1 1/4-1-1/4 (6-31mm) FP Complete w/nozzle Mixer TUR W-J-CS 2 1/2-1-1/2 (12-38mm) FP Complete w/nozzle Mixer NOTE: Oxygen consumption (SCFH) is 1.1 times acetylene for a neutral flame. 795

29 OXYGEN-ACETYLENE CUTTING & BRAZING EQUIPMENT REPLACEMENT HANDLES & CUTTING ATTACHMENTS FOR CWK SERIES FP Handle (TUR ) Forward valves ribbed barrel for sure grip. A Hose Fittings, 3/8-24 Threaded joints provide easier service Control valves use stainless steel ball stems and teflon packing for smooth gas-tight operation FP Cutting Attachment (TUR ) Use with FP Handle Internal spiral mixer mixes oxygen and fuel for optimum performance Smooth action of cutting oxygen valve allows precise control Stainless steel lever for durability Double O-ring seal Stainless steel tubes for superior strength REPLACEMENT HANDLES & CUTTING ATTACHMENTS FOR 100 SERIES FP Handle (TUR ) Built in flashback arrestors and reverse flow check valves for added safety Threaded joints provide easier service Control valves use stainless steel ball stems and teflon packing for smooth gas tight operation Rearvalves Ribbed barrel stock for sure grip B 9/16-18 hose fittings FP Cutting Attachment (TUR ) Use with FP Handle Internal spiral mixer mixes oxygen and fuel for optimum performance Smooth action of cutting oxygen valve allows precise control Stainless steel lever for durability Double O-ring seal REPLACEMENT ACETYLENE & OXYGEN REGULATORS HIGH PRESSURE GAUGE LOW PRESSURE GAUGE DELIVERY RANGE MODEL NO PSIG KPA PSIG KPA PSIG KPA TUR FP Acetylene CGA TUR FP Oxygen CGA , REPLACEMENT GAUGES TUR TUR TUR TUR DESCRIPTION 1-1/2 x 30 lbs. gauge 1-1/2 x 100 lbs. gauge 1-1/2 x 400 lbs. gauge 1-1/2 x 4000 lbs. gauge 796

30 OXY/ACETYLENE SPECIALTY TIPS & ACCESSORIES Tough jobs made easy with our new line of small brazing tips. Multi-Flame Heating Nozzles For heating, straightening, bending, brazing. Spiral Mixer provides optimum flame characteristics. Dual Flame Twin Tips For flexibility and control. MODEL NO Brazing capacity TUR D-1 1/4-7/8 TUR D-2 1/2-1-1/8 Wrapper Tips For complete distribution. MODEL NO Brazing capacity TUR VW-1 1/2-1 TUR VW-2 5/8-1-1/8 TUR VW-3 7/8-1-5/8 DESCRIPTION MODEL NO Brazing capacity TUR For use with CWK VMA-J-15 1/8-2-5/8 Series handle. TUR For use with 100 Series handle. VMA /8-2-5/8 Multi-Flame Heating Tip For maximum heating in a confined area. MODEL NO Brazing capacity TUR VMA 1/4-1-3/4 Single Flame Tips Pin-point precise heat. Tip Extensions Target those hard to reach places. MODEL NO Flexible extension TUR E-6 6 TUR E MODEL NO Brazing capacity Size TUR V-1 1/4-7/8 1 TUR V-2 1/2-1 2 TUR V-3 5/8-1-1/8 3 Mixer-Adapters For TurboTorch oxy-acetylene handles. DESCRIPTION MODEL NO TUR Fits CWK kit handle VM-J #103-01FP (Forward valve) TUR BraFits 110 kit handle #101-0FP (Rear valve) VM-I 797

31 NITROGEN PURGING EQUIPMENT & ACCESSORIES Purging Regulator (TUR P) TurboTorch offers a nitrogen regulator with easy to read 2 (51mm) gauges. Constructed of forged brass, designed for testing and purging brazed joints. This regulator is recommended by many air conditioning code organizations for joint testing at commercial job sites. HIGH PRESSURE GAUGE LOW PRESSURE GAUGE DELIVERY RANGE MODEL NO PSIG KPA PSIG KPA PSIG KPA TUR P Nitrogen CGA , TUR P Nitrogen CGA , *Gauges scale = PSIG/KPA Replacement Gauges TUR TUR TUR DESCRIPTION 2 x 4000 lbs. gauge 2 x 400 lbs. gauge 2 x 600 lbs. gauge TT-LP TurboTest Refrigerant Leak Detector (TUR ) The TurboTest Total LP Leak Detector fits standard TurboTorch MAPP (MT-1) or Propane (PT-1) tanks. The TurboTest Total LP is compact, easy to use and capable of detecting leaks of 8 oz. per year. It s made of brass construction with a stainless steel shield. Sniffer tube swivels 360 for easy handling. Heavy copper reactor plate (TT-R-LP) gives extra long life, yet is easily replaceable. Rugged stainless steel shroud will not rust. Easy-to-clean orifice is easily removed, reversed and blown clean. Steady, uniform swirl combustion flame. Complete operating instructions are included. NITROGEN PURGE & BLOW GUN KITS NPK-20 (TUR ) 6 ft/1.8m hose OSHA rated blow gun Regulator P Carrying Case Multiple Uses: purges, blows, leak tests NPK-40 (TUR ) 6 ft/1.8m hose OSHA rated blow gun Regulator P Carrying Case Multiple Uses: purges, blows, leak tests Blow Gun Accessories MODEL NO DESCRIPTION TUR TT cu. ft. Carrying Case TUR TT cu. ft. Carrying Case TUR NT cu. ft. Nitrogen Cyl. TUR BG Blow Gun TUR BGH Blow Gun Hose 798

32 BRAZING AND SOLDERING ALLOYS Aluminum Brazing Alloy AK-1 (TUR ) Aluminum brazing alloy rod and flux for aluminum products, even anodized aluminum. Ideal for refrigerant coil and tubing repair. Kit includes rod and self-cleaning flux. Brazing Alloys for Maintenance on Steel Products BF-1 Bronzeflow (TUR ) (for steel materials other than stainless steel - available in 1 lb. or 25 lb. package) Brazing range F ( C) for low fuming bronze. Ideal for maintenance repairs on plumbing and heating. Tensile strength - 63,000 psi. Meets AWS A5.8, ASTM B-259, Federal QQR571B, MIL-R-19631B specifications. NS-1 NicSil-Flow (TUR ) (for stainless steel and chrome-plated products) Nickel content brazing rod. Low fuming type nickel-bronze alloy. Brazing range F. Tensile strength - 70,000 psi. Meets AWS A5.8, ASTM B- 259, Federal QQR571B, MIL-R-19631B specifications. SILVER/COPPER/PHOSPHORUS BRAZING ALLOYS These alloys are regularly used in the HVAC industry, especially for joining copper tubing. No flux is required when joining copper- to-copper. Higher silver content offers better flow control and several compositions are available to match your price/performance range. Available in a 1 lb. /.45 kg. MODEL NO. SILVER CONTENT SF-1 1 lb. 0% SF-2 1 lb. 2% SF-5 1 lb. 5% SF-6 1 lb. 6% SS-15 1 lb. 15% CHEMICAL COMPOSITION 0% Silver 7.1% Phosphorus Balance Copper 2% Silver 7% Phosphorus Balance Copper 0.15% All Other 5% Silver 6% Phosphorus Balance Copper 0.15% All Other 6% Silver 6.5% Phosphorus Balance Copper 0.15% All Other 15% Silver 5% Phosphorus Balance copper SPECIFICATIONS LIQUIDUS SOLIDUS TYPICAL APPLICATIONS AWS A5.8 BCuP-2 QQB- 650B AWS/A5.8 Class BCuP-6 QQB-650C Class BCuP-6 AWS/A5.8 Class BCuP-3 ASMESFA5.8 Class BCuP-3 QQB-650B Class BCuP-3 AWS A5.8 QQB-650A MIL-E-15395A 1500 F 816 C 1450 F 788 C 1500 F 816 C 1425 F 774 C 1465 F 796 C 1350 F 732 C 1190 F 643 C 1190 F 643 C 1190 F 643 C 1190 F 643 C Moving joints Non-moving joints T-joints, swage joints, sleeves Coupling on return bends and condenser fittings Extending copper tubing and pipes Flexible pipe connectors Refrigeration control valves (copper and brass) Joining copper wires to rotor bars Building up control valves Electrical Connectors Radiant heating systems Air conditioning units Hot and cold water lines Steam systems Heat exchanges Copper Joints Note:.45 kg per pound, kg equals 25 lbs. 799

33 TANK CARRIERS & TOTES (TUR ) Fits 10 cu. ft. acetylene AC-MC and 20 cu. ft. OX-20 oxygen cylinders. TSR Tank Rack (TUR ) A durable wire frame and spring combination holds 1 lb. tanks securely at a 45 angle from the floor (TUR ) Wheeled cylinder truck. Accommodates 40 or 10 cu. ft. acetylene and 40 or 20 cu. ft. oxygen cylinders TT-150 (TUR ) Durable composite construction fits B tank. Features include a hose rack for storage while not in use and helps protect the regulator from accidental damage. A large handle keeps your tank portable. Your spark lighter is close at hand in its own holder accessory. B tote can be changed from one tank to another without special tools. A heavy nylon belt can keep your outfit secure on scaffolds or in the truck. TT-MCR (TUR ) Heavy duty steel construction fits MC and OX-20 (R) tank. Storage for tips, hose, handle and cutting attachments. Use Adapter for use with MT-1 (not included). TT-MC (TUR ) Heavy duty steel construction fits MC tank or MT-1 MAPP tank. Easy storage of tips, handle, hose and striker. TT-B (TUR ) Heavy duty steel construction fits B tank. Storage for tips, hose, handle and striker. 800

34 CYLINDERS AND TANKS PT-1 (TUR ) Propane replacement tank for use with all TurboTorch hand torches. Also for use with TurboTorch #TT-LP Leak Detector. Contains 14.1 oz. propane. CGA 600 Connection Non-Refillable MT-1 (TUR ) MAPP Gas replacement tank for use with TurboTorch dual fuel hand torches. Also use with TurboTorch #TT-LP Leak Detector. Contains 16 oz. of MAPP Gas. CGA 600 OX-20 (TUR ) Type R Oxygen Cylinder, 20 cu. ft. capacity. CGA 540 Connection Fits TurboTote Case OX-40 (TUR ) Type 40 Oxygen Cylinder, 40 cu. ft. capacity. CGA 540 Connection AC-B (TUR ) Type B Acetylene Cylinder, 40 cu. ft. capacity. CGA 520 Connection AC-MC (TUR ) Type MC Acetylene Cylinder, 10 cu. ft. capacity. CGA 200 Connection Fits TURBOTOTES CASE T-10PS-MT (TUR ) Tank with 10 lb. capacity. Refillable with Propane. CGA 510 POL Connection 17-1/2 (44cm) high 8 (20cm) O.D. NT-40 (TUR ) 40 cu. ft. Nitrogen Cylinder CGA 580 Connection 801

35 ACCESSORIES Oxy/Acetylene Twin Hose DESCRIPTION MODEL NO TUR /2 ft. Twin Hose A Fitting P Acetylene Hose DESCRIPTION MODEL NO TUR ft. Hose A Fitting AH-12 TUR ft. Hose A Fitting AH-24 Total LP Hose DESCRIPTION MODEL NO TUR ft. Hose B Fitting H-12 TUR ft. Hose B Fitting H-24 TORCH SHIELD Durable Fabric (8 X 12 ) Roll it up and stuff it in your pocket. Re-Useable Can be used 20, 50, Times. Will not burn or melt. Center-Cut Design Unique design makes it easier to use. Multi-Use Ideal for Brazing, Soldering or Welding. Safe to Use No toxic smoke, made of non-asbestos, non-ceramic materials. TUR L-1 Single Flint Striker (TUR ) Cup type, round flie MODEL NO PL-812 Triple Flint Striker Refills (TUR ) Triple Flint Striker (TUR ) TK Tank Key (TUR ) Wrench for B & MC Tanks GOGGLES P (TUR ) 2 x 4 Goggles Shade Number 5 Coverall Style to wear over prescription or safety glasses 802

36 TPC-18 AND TPC-25 TPC-18 1/8 Cutting System (TUR ) Specifications Output: amps fixed Input: Volts (+/-10%) 1 Phase, 60 Hz, 20 Amps Cut Capacity:... 1/8" (3.2mm) Duty Cycle:... 30% Panel Controls:... On/Off Lighted Dimensions:... Height: 10" (254mm) Width:..9" (229mm) Length:...16" (406mm) Weight: lb (25Kg) Gas:... Air from built in air compressor Pilot:... Electrode to Tip Control:... Torch mounted switch Lead Length: ft (6.1m) TPC-25 1/8 Cutting System (TUR ) Specifications Output:...20 amps fixed Input Power: V (+/- 10%) 1 Phase, 60 Hz, 20 amp Cut Capacity:...1/4" (6.4 mm) Duty Cycle:... 40% Panel Controls:...On/Off Pressure regulator Dimensions:...Height: 3.25" (337 mm) Width: " (172 mm) Length:17.5" (445 mm) Weight:...40 lb. (18.2 kg) Gas:...Air/N2 Gas Pressure:...50 PSI (3.5 BAR) Gas Flow: SCFH (64 lpm) Pilot:... Electrode to tip Control:...Torch mounted switch Lead Length: ft. (7.6 m) TORCH CONSUMABLES Ordering Information DESCRIPTION MODEL NO TUR Shield Cup for TPC-18 & TPC-25 (1pk) TSC-25 TUR Cutting tip for TPC-18 Only (5pk) T-Tip-18 TUR Cutting tip for TPC-25 Only (5pk) TCT-25 TUR Gas Distributor for TPC-18 & TPC-25 (1pk) TGD-25 TUR Electrode for TPC-18 & TPC-25 (5pk) TE

37 PRESTO-LITE WELDING AND CUTTING OUTFITS Prest-O-Lite Maintence Outfit Prest-O-Lite Outfits feature the W-200 torch handle with piston type connection for hand tightening, welding and soldering heads. Patented explosion protection is built into each regulator. The Outfit can be ordered as a Prest-O-Pak with tote or tote and tanks. Prest-O-Pak DLX Maintenance Outfit MC w/tote POL Prest-O-Pak DLX Maint. Outfit MC Tote w/tanks POL Outfits Contain W-200 Torch CW-200 Cutting Attachment Cutting Tip 4202, 1/2 in. Air-Gas Adaptor Air-Gas Soldering Tip #3 Brazing Tip #6 Oxygen Regulator R A Acetylene Regulator R MC Striker Goggles Hose 12-1/2 ft. x 3/16 in. A-A T Grade Tote Optional Oxygen Tank R, 20 Cu. Ft. Acetylene Tank MC, 10 Cu. Ft. POL POL-05L20 POL-16K09 POL POL-10X23 POL- 06L49 POL POL-05X02 POL-790F34 POL POL-591F72 POL-791F80 POL POL Welding, Cutting and Heating Ranges Outfit as furnished Outfit with optional heads and nozzles Welding Range Up to 1/16 in. Up to 3/8 in (10 mm) (1.5 mm) Cutting Range Up to 1/2 in. (13 mm) Up to 2 in. (50 mm) Heating Range Up to 6 cfh acet. Up to 40 cfh acet. (8,850 Btu/hr.) (58,667Btu/hr.) 804

38 PRESTO-LITE WELDING AND CUTTING OUTFITS Prest-O-Lite Brazing Outfit Prest-O-Pak DLX Brazing Outfit MX w/tote POL Prest-O-Pak DLX Brazing Outfit MC Tote w/tanks POL Out contain W-200 Torch POL Welding Head # 4 POL-06L48 Welding Head # 9 POL-06L50 Oxygen Regulator R A POL Acetylene Regulator R MC POL-05X20 Striker POL-790F34 Goggles POL Hose 12-1/2 ft. x 3/16 in A. A T Grade POL-591F72 Tote POL Optional Oxygen Tank R, 20 CU. Ft. POL Acetytene Tank MC, 10 Cu. Ft. POL Welding and Heating Ranges Outfit as furnished Outfit with optional heads and nozzles Welding Range Up to 1/8 in. (3 mm) Up to 3/8 in. (10 mm) Heating Range Up to 9 cfh acet. Up to 40 cfh acet. (13,300 Btu/hr.) (58,667 Btu/hr.) PRESTO-LITE PZ503 TORCH KIT FG-2 is the economical, high-energy fuel gas. Excellent for soldering, brazing and heating. Uses PZ- 503 high output self-igniting torch with adjustable flame. Pull the trigger, it s on, release the trigger, it s off. High output swirl action with instant on-off Interchangeable burn tip converts to: general purpose flame, or pencil flame Heavy duty piezo igniter Cast aluminum body 100%firetested Built-in pressure regulator makes it perfect for brazing or soldering in any position, even upside down! Has adjustable flame control for even greater versatility PZ503 Kit POL FG-2 MAPP PROPANE Flame Temperature in Air 3400 F 3400 F 3300 F Cubic Feet of Gas/Pound, 70 F Air to Gas Ratio 12:1 12:1 20:1 Cold Weather Performance Excellent Poor Poor Pressure, at 32 F, Full Cylinder 87 psig 68 psig 63 psig Pressure, at 0 F, Full Cylinder 43 psig 30 psig 25 psig 805

39 AIR-ACETYLENE SWIRLJET KITS X-3B POL Kit Flexible kit bronze brazes light/medium gauge steel Soft solders to 4 in. (100 mm) Silver brazes to 2 in. (50 mm) B tank connection X-4B POL Kit High capacity kit bronze brazes medium/heavy gauge steel Soft solders to 6 in. (150 mm) Silver brazes to 4 in. (100 mm) B tank connection X-5B POL Kit Flexible lighter duty kit Soft solders to 2 in. (50 mm) Silver brazes to 1 in. (25 mm) B tank connection Kit Components and Ordering Information DESCRIPTION Kit Contains POL X-3B Kit -- POL X-4B Kit -- POL R-511 B (CGA520) Regulator POL POL QD#1 Torch POL QD-SJ-3A Tip (X-3B only) POL QD-SJ-4A Tip POL QD-SJ-5A Tip (X-4B only) POL-501F12 -- Hose 12-1/2 ft. x 3/16 in. A-A POL X-5B Kit -- POL R-511 B (CGA 520) Regulator or POL R-511 MC (CGA 200) Regulator POL POL QD #1 Torch POL QD-SJ-3A Tip POL-501F12 -- Hose 12-1/2 ft. x 3/16 in. A-A POL-790F34 -- Friction Lighter (X-5B only) 806

40 SWIRLJET TIPS AND TORCH HANDLE Interchangeable with Turbo Torch and Goss Handles and Tips Specifications and Ordering Information These Swirljet tips are designed to be used with the PREST-O-LITE #1 Quick Disconnect to They run quieter and cooler and give better heat transfer than other comparable tips. COPPER TUBING SIZE CAPACITY DESCRIPTION Soft Solder in Silver Braze in POL POL #1 Quick Disconnect Torch Handle Replaces Turbo Torch Model G-4 Fuel Pressure PSIG Gas Flow CFH POL QD-SJ-3A up to 2 1/2-1 A-8 Acetylene POL QD-SJ-4A A-14 Acetylene POL QD-SJ-5A A-32 Acetylene POL QD-SJ-3LPG 1/4-1-1/2 1/4-1 /2 T-3 FG-2* POL QD-SJ-4LPG 1/4-2-1/2 1/4-1-1/4 T-4 FG-2* POL QD-SJ-5LPG 1-4 1/2-2 T-5 FG-2* POL QD-SJ-6LPG 1-6 3/4-4 T-6 FG-2* *These tips can also be used with Propane and MAPP Gas (refer to instruction literature for appropriate pressures and flows for these gases). TurboTorch is a registered trade name of Thermadyne. Tanks and Carriers R Oxygen Tank holds 20 cu. ft. new, empty MC Acetylene Tank holds 10 cu. ft. new, empty Kangaroo Kart is a strong, lightweight polypropylene carrier for an MC acetylene tank and an R oxygen tank. Includes handy accessory compartment. Ordering Information R Oxygen Tank MC Acetylene Tank Kangaroo Kart Nitrogen Cylinder Stand POL POL POL-791F80 POL-88F82 Single Flint Lighter Specially hardened file surface over one square inch Fat spark flint strikes file at angle Quick ignition protection cup forms gas-collect File turns automatically equalizes wear Easily replaceable flints Individually blister-packed Ordering Information DESCRIPTION POL-790F34 Single Flint Lighter Heavy-Duty Model (Box of 10) 807

41 PREST-O-LITE WELDING AND CUTTING OUTFITS Welding Kit The New Sabre V Series Light Duty Welding and Cutting Outfits Interchangeable with Uniweld and TurboTorch. Welding Kit With Tanks Welding Kit QJ28 Welding Handle QWJ-2 Light Duty #2 Welding Nozzle QWJ-4 Light Duty #4 Welding Nozzle Oxygen Regulator R A Acetylene Regulator R A MC Twin Hose A-A 12-1/2 ft. A-A Tote Striker Goggles Welding Kit with Tanks Oxygen Tank R, 20 Cu. Ft. Acetylene Tank MC, 10 Cu. Ft. NITROGEN PURGE & BLOW GUN KITS NPK-40TS (POL-22545) 40 cu. ft. tank, refillable, empty 6 ft /1/8m hose OSHA rated blow gun Regulator, R Carrying stand Multiple uses: purges, blows, leak tests POL POL POL POL POL POL POL-591F72 POL-791F80 POL-790F34 POL NPK-40S (POL-22546) 6 ft / 1/8m hose OSHA rated blow gun Regulator, R Carryingstand Multiple uses: purges, blows, leak tests Nitrogen Purge Kit DESCRIPTION MODEL NO POL-88F82 40 cu. ft. Carrying Stand NPA-S POL cu. ft. Nitrogen Cylinder NPA-T POL Blow Gun NPA-G POL Charging Hose 6 ft NPA-H POL Blow Gun and Hose Assembly NPA-GH POL Blow Gun, Hose Assy. & Regulator NPA-GHR 808

42 AIR FUEL OUTFITS 4-in-1 Outfit with Soft Flame Tips For all purpose soldering, heating and brazing Meets most industrial demands B tank and MC tank models available Interchangeable tips for proper flame size and heat Change tips in seconds no tools necessary; tips lock in any working position Common torch handle provides equivalent of five outfits Adjustable pressure regulator for steady gas delivery and stable flames DESCRIPTION Outfits Contain POL-30X63 Prest-O-Lite 4-in-1 Outfit B 403 Torch Handle POL-30X64 Prest-O-Lite 4-in-1 Outfit MC #1A Soft Flame Brazing Tip POL-02X93 -- #3 Soft Flame Brazing Tip POL #4 Soft Flame Brazing Tip POL-10X23 -- #5 Soft Flame Brazing Tip POL-10X24 -- R-411 B Regulator or POL-10X25 -- R-411 MC Regulator POL-04X36 -- Hose 12-1/2 ft. x 3/16 in. A-A POL-04X POL-501F General Purpose Air-Acetylene Outfits with Soft Flame Tip For sweat-type fittings, heating and brazing Ideal for copper, brass, steel and wrought iron pipe with solder-type fittings Precision flame control for joints near a wall, against each other and in hard-to-reach places Instant heat 4000º F, without pumping or priming Convenient small, light, easy to handle and always ready to use Efficient ample range for run-of-shop work; unaffected by drafts, wind and rain B tank and MC tank models available Adjustable pressure regulator with contents gauge and delivery pressure indicators on pressure adjustment knob DESCRIPTION General Purpose Outfits contain POL-30X37 Prest-O-Lite General Purpose Outfit B 403 Torch Handle POL-30X38 Prest-O-Lite General Purpose Outfit MC #4 Soft Flame Brazing Tip POL-02X93 -- R-411 B Regulator or POL-10X24 -- R-411 MC Regulator POL-04X36 -- Hose 12-1/2 ft. x 3/16 in. A-A POL-04X POL-501F POL PZ

43 KLEIN SCREWDRIVERS HEAVY-DUTY SQUARE SHANK, KEYSTONE-TIP Designed for the most demanding uses. With heavy-duty square shank for wrench -assisted turning. Keystone-tip. SHANK TIP WIDTH x SHANK LENGTH in (mm) OVERALL LENGTH in (mm) KLE /4 x 1-1/2 (6 x 38) 3-7/16 (87) KLE /4 x 4 (6 x 102) 8-11/32 (212) KLE /16 x 6 (8 x 152) 10-15/16 (278) KLE /8 x 8 (10 x 203) 13-7/16 (341) KLE /2 x 12 (13 x 305) 17-7/16 (443) HEAVY-DUTY ROUND-SHANK, KEYSTONE-TIP Built to handle the tough jobs with ease. Keystone-tip. SHANK TIP WIDTH x OVERALL LENGTH in (mm) SHANK LENGTH in (mm) KLE /32 x 3 (6 x 76) 6-3/4 (171) KLE /4 x 4 (6 x 102) 8-11/32 (212) KLE /16 x 6 (8 x 152) 10-15/16 (278) KLE /8 x 8 (10 x 203) 13-7/16 (341) KLE /8 x 10 (10 x 254) 15-7/16 (392) KLE /8 x 12 (10 x 305) 17-7/16 (443) HEAVY-DUTY ROUND-SHANK, CABINET-TIP Heavy-duty shank and tip for rugged usage. Narrow tip permits blade access where space is limited. SHANK TIP WIDTH x OVERALL LENGTH in (mm) SHANK LENGTH in (mm) KLE /4 x 4 (6 x 102) 8-11/32 (212) KLE /4 x 6 (6 x 152) 10-11/32 (263) KLE /4 x 8 (6 x 203) 12-11/32 (314) KLE /4 x 10 (6 x 254) 14-11/32 (365) ROUND-SHANK, SPECIAL PROFILATED PHILLIPS-TIP Tips are profilated to provide a more consistent geometric symmetry than conventional Phillips-tip screwdrivers. Provide more accurate fit and torque without slippage. SHANK TIP WIDTH x SHANK LENGTH in (mm) OVERALL LENGTH in (mm) POINT SIZE KLE /2 (38) 3-7/16 (87) No. 2 KLE (76) 6-3/4 (171) No. 1 KLE (102) 8-5/16 (211) No. 2 KLE (152) 11 (279) No. 3 KLE (178) 11-5/16 (287) No. 2 KLE (254) 14-5/16 (364) No. 2 ROUND-SHANK, CABINET-TIP Perfect for electrical and telephone work. Narrow tip permits blade access where space is limited. SHANK TIP WIDTH x OVERALL LENGTH in (mm) SHANK LENGTH in (mm) KLE /16 x 3 (5 x 76) 6-3/4 (171) KLE /16 x 4 (5 x 102) 7-3/4 (197) KLE /16 x 6 (5 x 152) 9-3/4 (248) KLE /16 x 8 (5 x 203) 11-3/4 (298) KLE /16 x 10 (5 x 254) 13-3/4 (349) SPECIALTY SCREW DRIVERS DESCRIPTION CONTAINS KLE in 1 5/16 in. and 1/4 in.nut drivers,#1 and #2 Phillips,1/4 in. and 3/16 in. slotted,#10 and #15 TORX, #1and #2 square-recess KLE in 1 5/16 in. nut driver, #1 and #2 Phillips, 9/32 in. slotted and 3/16 in. slotted KLE in 1 Screwdriver with two dual-tipped blades. Overall length 7-5/8 in. (194 mm) *Individually carded TOTALINE LOGO SCREW DRIVERS DESCRIPTION OVERALL LENGTH in 1 Ratcheting 7-1/2 in B 6 in 1 Screwdriver 7-1/2 in in 1 Screwdriver 7-1/2 in. SLOTTED SCREW-HOLDING SCREWDRIVERS Split-blade screw-holding driver wedges into screw slot. Positive gripping actions holds, starts, and drives slotted screws in awkward, hard-to-reach places. SHANK TIP WIDTH x OVERALL LENGTH SHANK LENGTH in (mm) KLE-K21* 1/8 x 3 (3.2 x 76) 5-1/4 (133) KLE-K34** 3/16 x 4 (4.8 x 102) 7-3/4 (197) KLE-K38** 3/16 x 8 (4.8 x 203) 11-3/4 (298) KLE-K46 1/4 x 6 (6.3 x 152) 10-1/4 (260) *Precision blade for use with small precision screws. Blade thickness of.028 inch expanding to.045 inch. **Blade thickness of.043 inch expanding to.085 inch. NOTE: K21 has pocket clips. 7-PIECE CUSHION-GRIP SCREWDRIVER SET KLE A convenient selection of popular screwdrivers including three cabinet-tip two Phillips-tip and two keystone-tip styles, all with Cushion-Grip high-quality design and construction features. Set is provided in recloseable sealtight vinyl pouch. OVERALL LENGTH in DESCRIPTION (mm) KLE /32 (212) Square-shank, keystone-tip* KLE /16 (278) Round-shank, keystone-tip* KLE /4 (171) Round-shank, cabinet-tip KLE /4 (248) Round-shank, cabinet-tip KLE /32 (202) Round-shank, cabinet-tip* KLE /4 (171) Round-shank, No.1 Phillips-tip KLE /16 (211) Round-shank, No. 2 Phillips-tip *Heavy-duty model. 810

44 KLEIN SCREWDRIVERS 7-PIECE COMBINATION SCREWDRIVER SET KLE Set contains two Phillips-tip Bull Drivers, two slotted Bull Drivers plus three popular cabinet-tip screwdrivers. Recloseable, seal-tight vinyl pouch. OVERALL LENGTH in (mm) DESCRIPTION KLE-BD /2 (216) No. 2 Phillips-tip Bull Driver KLE-BD /8 (168) No. 1 Phillips-tip Bull Driver KLE-BD /16 (284) Square-shank, slotted Bull Driver KLE-BD /2 (216) Square-shank, slotted Bull Driver KLE-A (152) Round-shank, cabinet-tip KLE-A (178) Round-shank, cabinet tip KLE-A (228) Round-shank, cabinet-tip KLEIN NUT DRIVERS SEVEN-PIECE 6-INCH-SHAFT NUT-DRIVER SET KLE Contains all seven 6-inch-shaft nut drivers below in a recloseable vinyl seal-tight pouch. HANDLE COLOR HEX SIZE (in) SHANK LENGTH in (mm) KLE-S66 Black 3/16 9-5/8 (244) KLE-S86 Red 1/4 9-5/8 (244) KLE-S106 Amber 5/16 9-5/8 (244) KLE-S116 Green 11/32 9-5/8 (244) KLE-S126 Blue 3/8 9-5/8 (244) KLE-S146 Brown 7/16 10 (254) KLE-S166 Red 1/2 10 (254) SEVEN-PIECE 3-INCH-SHAFT NUT-DRIVER SET KLE-K7 Set contains seven hollow-shaft nut drivers in the most popular hex sizes. Convenient vinyl pouch hangs up, rolls up, stands up. OVERALL LENGTH HANDLE COLOR HEX SIZE (in) in (mm) KLE-S6 6-5/8 (168) Black 3/16 KLE-S8 6-5/8 (168) Red 1/4 KLE-S10 6-5/8 (168) Amber 5/16 KLE-S11 6-5/8 (168) Green 11/32 KLE-S12 6-5/8 (168) Blue 3/8 KLE-S14 7 (178) Brown 7/16 KLE-S16 7 (178) Red 1/2 MAGNETIC NUT DRIVERS Similar to standard nut drivers but with powerful nutholding magnet built into shank. Features same quality materials and workmanship as hollow-shaft tools. OVERALL LENGTH in (mm) HANDLE COLOR HEX SIZE (in) SHANK LENGTH in (mm) KLE-S8M 6-5/8 (169) Red 1/4 3 (76) KLE-S10M 6-5/8 (169) Amber 5/16 3 (76) KLE-S86M 9-5/8 (244) Red 1/4 6 (152) KLE-S106M 9-5/8 (244) Amber 5/16 6 (152) KLE-S818M 21-5/8 (549) Red 1/4 18 (457) KLE-S1018M 21-5/8 (549) Amber 5/16 18 (457) INDIVIDUAL CUSHION-GRIP, HOLLOW-SHAFT NUT DRIVERS The finest nut drivers made. Rugged and solid from end to end. Amber plastic handle with Cushion-Grip is comfortable, never hurts the hand; permits the use of maximum turning power without discomfort. Handle caps are color-coded for easy size identification. Strong hexhead drives nuts and socket screws. Full hollow-shaft chrome-plated shank permits turning nuts on long screws. In nine individual sizes or a 7-piece set. HEX SIZE (in) SHANK LENGTH in COLOR CODE (mm) KLE-630-3/16 3/16 3 (76) Black KLE-630-1/4 1/4 3 (76) Red KLE-630-5/16 5/16 3 (76) Yellow KLE /32 11/32 3 (76) Green KLE-630-3/8 3/8 3 (76) Blue KLE-630-7/16 7/16 3 (76) Brown KLE-630-1/2 1/2 3 (76) Red KLE-630-9/16 9/16 4 (102) Orange KLE-630-5/8 5/8 4 (102) Yellow 7-PIECE CUSHION-GRIP NUT-DRIVER SET KLE-631 Consists of seven nut drivers. HEX SIZE (in) SHANK LENGTH in COLOR CODE (mm) KLE-630-3/16 3/16 3 (76) Black KLE-630-1/4 1/4 3 (76) Red KLE-630-5/16 5/16 3 (76) Yellow KLE /32 11/32 3 (76) Green KLE-630-3/8 3/8 3 (76) Blue KLE-630-7/16 7/16 3 (76) Brown KLE-630-1/2 1/2 3 (76) Red 2-PR MAGNETIC HOLLOWSHANK NUT DRIVERS HEX SIZE (in) SHANK LENGTH in COLOR CODE (mm) KLE-610M 1/4 & 5/16 1-1/2 (38) Red-Yellow KLE-630M 1/4 & 5/16 3 (76) Red-Yellow KLE-646M 1/4 & 5/16 6 (152) Red-Yellow KLEIN SHEET METAL TOOLS NIBBLER TOOL This 5-Blade Crimper produces factory-precision indentations in stove pipe and round duct with just a squeeze. The compound -leverage mechanism, heavyduty jaw/handle linkage, and closing stop provide easy operation and consistent crimps for virtually leak- proof connections. The spring-actuated, narrow-opening handles are covered with blue vinyl grips and have carefully placed hand stops for extra comfort. Hardened steel construction and nickel plating provide long life and consistent crimp profile. KLE-76011B KLE DESCRIPTION Nibbler cutting tool complete with blade. Replacement blade for No. KLE-76011B Nibbler cutting tool. 811

45 KLEIN SHEET METAL TOOLS 5-BLADE CRIMPER Klein 5 - Blade Crimper This 5-Blade Crimper produces factory-precision indentations in stove pipe and round duct with just a squeeze. The compound-leverage mechanism, heavyduty jaw/handle linkage, and closing stop provide easy operation and consistent crimps for virtually leak-proof connections. The spring-actuated, narrow-opening handles are covered with blue vinyl grips and have carefully placed hand stops for extra comfort. Hardened steel construction and nickel plating provide long life and consistent crimp profile. Produces factory-precision indentations in stove pipe and round duct, hardened steel construction and nickel-plated. DESCRIPTION KLE BLADE CRIMPER STRAIGHT AND OFFSET HAND SEAMERS Klein Straight Hand Seamer Bend and flatten sheet metal and non-ferrous metals easily with these rugged hand seamers. Straight-handle model used for most general applications, offset-handle for use in overhead or confined areas. The compoundleverage design gives accurate control and powerful grip for making quick, permanent, tight-fitting seams. The 3-1/4 in. wide drop-forged, high-impact steel jaws are marked in ¼ in. increments for precise bending measurements. Hardened steel handles are covered with blue vinyl grips with handle stops for added comfort and easy operation. The all-steel construction and nickel-plated hardware provide long life and durability. Bend, flatten sheet metal and non-ferrous metals, for general applications, 8 in. overall length. DESCRIPTION KLE Straight Hand Seamer, 8 in. overall length Klein Offset Hand Seamer Bend, flatten sheet metal and non-ferrous metals, use in overhead or confined areas, allsteel and nickel plated, 8 in. overall length. AVIATION SNIPS Compound action increases leverage for maximum cutting ease. Cuts all sheet metals up to 18-gauge with half the effort of conventional snips. Available in left, right, and straight cutting patterns. Hot drop-forged jaws of tough, durable molybdenum steel to stand up under compoundlever action and the cutting of heavy stock. Self-opening action for fast, easy feed. Latch keeps jaws closed when not in use. Length of cut 1-3/8 in. (3.5 cm). Handles of electric-furnace steel for extra strength. Handles are contoured and plastic-dipped to provide a firm, comfortable grip; color-coded by cutting pattern. OVERALL LENGTH in (mm) DESCRIPTION COLOR CODE CUTTING PATTERN KLE-1100L 9-3/4 (24.8) Red Left KLE-1101R 9-3/4 (24.8) Green Right KLE-1102S 9-3/4 (24.8) Yellow Straight KLE-P /4 (24.8) Replacement Spring Yellow Straight for Nos. KLE-1100L and KLE-1102S. KLE-P /4 (24.8) Replacement Spring for Nos. KLE-1101R. Yellow Straight HAND NOTCHER Make clean, 30 V -shaped cuts in sheet metal quickly and easily with this powerful hand notcher. The dropforged, high-impact steel jaw has a maximum throat depth of 13/16 in. and a hook design for easy notching of corners and take-off tabs without slippage. All steel construction with nickel-plate and black-oxide finish provides long life and durability. Blue vinyl grips with handle stops for added comfort and easy operation. DESCRIPTION KLE Hand Notcher, 8 in. overall length MEASURING TAPES COLOR CODE BLADE LENGTH ft WIDTH in (mm) (m) KLE Chrome 12 (3.5) 3/4 (19) KLE Chrome 16 (5) 3/4 (19) KLE Chrome 25 (7.5) 1 (25) KLE Chrome 30 (8) 1 (25) KLE HV Orange 16 (5) 3/4 (19) KLE HV Orange 25 (7.5) 1 (25) KLE RE Orange 16 (5) 1 (25) KLE RE Orange 25 (7.5) 1 (25) KLE RE Orange 25 (7.5) 1-1/4 (32) KLE RE Orange 30 (9) 1 (25) KLE Blue 12 (3.5) 5/8 (16) KLE Blue 16 (5) 1 (25) KLE Blue 25 (7.5) 1 (25) KLE Blue 30 (8) 1 (25) KLE DESCRIPTION Offset Hand Seamer, 8 in. overall length 812

46 KLEIN ADJUSTABLE WRENCHES STANDARD-JAW DESIGN KLEIN ADJUSTABLE WRENCHES FULLY-REVERSIBLE RATCHETING WRENCH Drop-forged alloy steel for maximum strength and lightweight. Chrome-plated. Part No supplied with tapered handles. LENGTH - in (mm) CAPACITY - in (mm) KLE (102) 1/2 (12) KLE (152) 3/4 (19) KLE (203) 15/16 (23) KLE (254) 1-1/8 (28) KLE (305) 1-5/16 (33) KLE (381) 1-11/16 (42) EXTRA-CAPACITY DESIGN Jaws open 3/16 in. (4 mm) wider than standard design wrenches, length for length. Extra capacity allows use of a smaller size wrench to handle bigger jobs. Ideal for use in confined spaces. Same rugged construction as standard design. Chrome plated. LENGTH - in (mm) CAPACITY - in (mm) KLE (152) 15/16 (23) KLE (203) 1-1/8 (28) KLE (254) 1-5/16 (33) KLE (305) 1-1/2 (38) KLEIN FOLDING HEX KEY SETS NINE-KEY SET Sizes (inch): 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4 HANDLE LENGTH in (mm) KEY LENGTHS in (mm) KLE /4 (108) 1-3/4 to 3-1/2 (44 to 89) EIGHT-KEY SET Sizes (inch):.050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64 and 5/32 HANDLE LENGTH in (mm) KEY LENGTHS in (mm) KLE /16 (78) 1-1/2 to 2-3/8 (38 to 60) Fully-reversible ratchet wrenches designed for refrigeration packing gland nuts and valve stem sockets. Also designed for beam-clamp installation. Wrenches are compact in size, with clearly marked sockets for four nut sizes. A quick/flip reversing lever permits instant ratchet reversal. Wrenches are ruggedly built and have polished chrome finish with smooth edges for comfort. LENGTH SOCKET SIZES (in) KLE /16 in. 3/16, 1/4, SQ. x 1/2, 9/16 hex KLE /2 in. 3/16, 1/4, 5/16, 3/8 STRIPPERS, CUTTERS, CRIMPERS WIRE STRIPPERS-CUTTERS Klein Wire Stripper/Cutter Compact, lightweight strippers gauge, cut, strip, and loop wire. Spring-loaded, self-opening action. Flat design makes them easy to store and carry. Narrow nose fits into tight places. Strip wire quickly, cleanly, evenly. Strong, hardened-steel with precision-ground stripping holes. Clear gauge markings on both sides. Black oxide finish. Comfortable plastic dipped handles. Overall length 6 in. (152 mm). StripsNo. 10 to 18 AWGsolid wire, easy-toreadwire gauge markings, comfortable cushion grip handles. HANDLE COLOR STRIPS AWG GAUGES KLE Yellow No. 10, 12, 14, 16, 18 solid wire (4.0, 2.5,1.5, 1.0, 0.75 mm2) LONG-NOSE ALL-PURPOSE TOOL 1010 Klein Long Nose All-Purpose Tool All-purpose cutter/crimper handles a wide range of sizes and functions: wire cutting, bolt cutting, wire stripping, and crimping including 7 to 8 mm ignition terminals. Cutters and strippers are in front of the pivot for maximum easeof-use in reaching into tight places. Tool features crimping dies for insulated and non-insulated connectors from 10 to 22 gauge (6.0 to 0.75 mm2 and cutters for 4-40, 5-40, 6-32, 8-32, 10-32, and bolts. Narrow, serrated plier jaws to pull, loop, and bend wire. Plastic-covered handles for maximum comfort. Strips and cuts wire, crimps insulated and non-insulated connectors from 10 to 22 gauge, crimps 7 to 8 mm ignition terminals, cuts bolts, pulls, loops and bends wire LENGTH - in (mm) KLE /4 (210) 813

47 STRIPPERS, CUTTERS, CRIMPERS CRIMPING TOOL 1005 Klein Crimping Tool - Non & Insulated Termils For insulated and non-insulated terminals and connectors. Thin nose permits work in confined space. Crimping die marked for insulated and non-insulated solderless terminals and connectors. Accommodates wire from No. 10 to 22 AWG. Wire cutter in nose. Red plastic- dipped handles for comfort. For insulated and non-insulated terminals and connectors, accommodates wire from No. 10 to 22 AWG, wire cutter in nose. LENGTH - in (mm) KLE /4 (248) KLE-J /4 (248) KLEIN PLIERS HIGH-LEVERAGE DIAGONAL CUTTERS High-leverage design provides a 36% greater mechanical cutting and gripping advantage than regular 7 in. and 8 in. heavy-duty diagonal cutters. Standard-bevel cutting knives. Plastic-dipped handles - handform style on No. D228-8, curved style on No. D DESCRIPTION A B C D KLE-D (203) 13/16 (21) 1-3/16 (30) 7/16 (11) KLE-D228-7 Same as D228-8 except length is 7 in. (178mm) with curved handles. 8 (203) 13/16 (21) 1-3/16 (30) 7/16 (11) HIGH-LEVERAGE NE-TYPE SIDE CUTTERS Our most popular side cutting pliers. Smooth, streamlined nose with knurled jaws. High-leverage design provides 46% greater cutting and gripping power than regular 8-1/2 in. and 9-1/4 in. side cutters. Blue plastic-dipped handles. DESCRIPTION A B C D E KLE-D213-8NE /2 (216) 1-7/16 (37) 1-7/32 (31) 5/8 (16) 23/32 (18) KLE-HD213-8NE With heavy-duty plastic-dipped handles. 8-1/2 (216) 1-7/16 (37) 1-7/32 (31) 5/8 (16) 23/32 (18) KLE-D213-9NE /4 (235) 1-19/32 (41) 1-5/16 (33) 5/8 (16) 25/32 (20) HIGH-LEVERAGE, DIAGONAL CUTTERS with ANGLED HEAD A B C D KLE-D (203) 13/16 (21) 1-3/16 (30) 7/16 (11) STANDARD LONG-NOSE with SIDE CUTTERS Standard long-nose design with cutting knives at hinge. Permits wrapping, looping, and cutting with a single pliers. Available with or without coil spring. Plastic-dipped handles. DESCRIPTION A B C D E F KLE-D /16 (141) 1-9/16 (40) 11/16 (17) 3/8 (10) 1/2 (13) 3/32 (2) KLE-D203-5C With 1/16" (1.6mm) point and coil spring. 5-9/16 (141) 1-9/16 (40) 11/16 (17) 3/8 (10) 1/2 (13) 3/32 (2) KLE-D /8 (168) 1-15/16 (49) 11/16 (17) 3/8 (10) 1/2 (13) 3/32 (2) KLE-D203-6C With 1/16" (1.6mm) point and coil spring. 6-5/8 (168) 1-15/16 (49) 11/16 (17) 3/8 (10) 1/2 (13) 3/32 (2) KLE With plain handles. 6-5/8 (168) 1-15/16 (49) 11/16 (17) 3/8 (10) 1/2 (13) 3/32 (2) KLE-D /8 (181) 2-7/16 (62) 11/16 (17) 3/8 (10) 1/2 (13) 3/32 (2) KLED203-7C With 1/16" (1.6mm) point and coil spring. 7-1/8 (181) 2-7/16 (62) 11/16 (17) 3/8 (10) 1/2 (13) 3/32 (2) 814

48 HAND CLEANER The base formula is a heavy-duty professional quality grade that is hard on dirt, but easy on your hands. Cleans without water Contains lanolin and aloe to moisturize and condition your skin Lotion consistency Yellow label KLE PUMICE HAND CLEANER Same as above, but without the scrubbing power of pumice Blue label KLE KLE RED DEVIL TOOLS TUF-KUT SCISSORS Sharp blades easily cut aluminum and carpet Made of stainless steel and high-impact plastic SIZE 14 oz. SIZE 7.5 oz. 14 oz. DESCRIPTION STANDARD PACK /8 in. (5 cm) serrated edge 10 CAULKING GUN 1/10 gallon, half barrel DESCRIPTION STANDARD PACK 3985 Caulking Gun Skeleton Gun 12 PUTTY KNIFE (STIFF) Black polypropylene handle is shatterproof and solvent- Durable, high-carbon, steel precision-ground blades extend through handles for maximum dependability. ALL-PURPOSE ADJUSTABLE UTILITY KNIFE Unique button locks blade to cut in different positions Contains extra blade STANDARD PACK RETRACTABLE RAZOR BLADE SCRAPER All metal construction with nickel-plate brass eyelets Contains extra blade STANDARD PACK HEAVY-DUTY BREAKAWAY UTILITY KNIFE Sturdy metal protective tip holds blade rigidly while cutting Stainless steel (no rust) breakaway blade has eight sharp cutting edges STANDARD PACK REPLACEMENT BLADES STANDARD PACK USED with KNIFE 3251 (5 card) /01 (100 pack) (3 card) (100 pack) RED DEVIL SPECIALTY DRY WALL KEYHOLE SAW 2757 Wallboard saw with a heavy-duty, tapered, sharp serrated blade. Makes it easy to cut and shape smaller openings without bending or flexing. Hardwood handle securely fitted to blade. Carded. 6 to shelf pack. 72 to case. ADJUSTABLE UTILITY KNIFE DESCRIPTION STANDARD PACK /2 in. (3.8 cm) wide-stiff Die-cast black metal knife with one blade. Open handle by removing screw to replace blades. Use replacement blade No Carded. Made in U.S.A. 6 to shelf pack. 72 to case. 815

49 COLORED EXTENSION CORDS by Baron COLORED VINYL TRI-SOURCE (3-WAY POWER BLOCK) Color-code your cords with bold combinations for easy identification on job site or truck. Bright colors attract attention and reduce possibility of theft. Custom colors are available from stock at no additional charge. UL listed - SJTW-A OSHA Color code: Various A B Lime Purple Green Orange Hot Pink Blue Gray Red Blue White DESCRIPTION STANDARD PACK PACKAGE WEIGHT /3 100 ft. SJTW-A Lime/Purple /3 100 ft. SJTW-A Hot Pink/Blue /3 100 ft. SJTW-A Green/Orange /3 100 ft.sjtw-a Gray/Red /3 100 ft. SJTW-A Blue/White BOLD COLORED CORD PRODUCTS FOR THE HVAC PROFESSIONAL If your good heavy extension cords keep disappearing from the job site, you need to take a stand get colored vinyl extension cords from Baron Wire. At Baron, we have taken our best 12-gauge vinyl extension cords and coded them in 5 bold color combinations combinations so bold, you ll be able to see your cords leave the site (and with whom) even at a distance. Choose one combination for all your company s cords as an inexpensive way to effectively code them for easy identification. Available in single receptacle or Tri-Source. POWER SUPPLY CORDS Power Supply Cords (Pigtails) Angled UL/CAS listed PVC jacket, STR BC Power/Solar Extension Cords, Tri-Source Cords Polar/Solar Extension Cord Sets UL/CAS listed - SJEOW - OSHA T-prene Color Code: Yellow (02) DESCRIPTION PACKAGE WEIGHT /3 25 ft. cord /3 50 ft. cord /3 100 ft. cord /3 25 ft. cord /3 50 ft. cord /3 100 ft. cord /3 25 ft. cord /3 50 ft. cord /3 100 ft. cord /3 25 ft. cord /3 50 ft. cord /3 100 ft. cord 67 Lighted Power/Solar Extension Cords Polar/Solar Plus Lighted Tri-Source (3 Way Power Block) UL listed - SEOW; SJEOW OSHA - T-prene Color Code: Yellow (02) DESCRIPTION PACKAGE WEIGHT /3 SJEOW, 25 ft. cord, 300 volt /3 SJEOW, 50 ft. cord, 300 volt /3 SJEOW, 100 ft. cord, 300 volt /3 SEOW, 2 ft. cord, 600 volt 15 Polar/Solar Lighted Power Indicator Receptacle UL listed - SJEOW OSHA - T-prene Color Code: Yellow (02) DESCRIPTION Power Supply Cord (Angled) 14/2 W/G SPT-3 5 ft. gray Power Supply Cord (Angled) 14/2 W/G SPT-3 6 ft. gray Power Supply Cord (Straight) 16/2 W/G SPT 3 ft. black Power Supply Cord (Straight) 16/2 W/G SPT 4 ft. black Power Supply Cord (Straight) 16/2 W/G SPT 5 ft. black Power Supply Cord (Straight) 16/2 W/G SPT 6 ft. black Power Supply Cord (Straight) 16/2 W/G SPT 8 ft. black Power Supply Cord (Angled) 16/2 W/G SPT-2 3 ft. black Power Supply Cord (Angled) 14/2 W/G SPT-3 4 ft. black Power Supply Cord (Angled) 14/2 W/G SPT-3 5 ft. black Power Supply Cord (Angled) 14/2 W/G SPT-3 6 ft. black Power Supply Cord (Angled) 14/2 W/G SPT-3 8 ft. black DESCRIPTION PACKAGE WEIGHT 14/3 25 ft. cord 27 14/3 50 ft. cord 26 14/3 100 ft. cord 25 12/3 25 ft. cord 21 12/3 50 ft. cord 25 12/3 100 ft. cord 25 10/3 50 ft. cord 42 10/3 100 ft. cord

50 ProPak Professional Series Merchandise Displays Professional Lighting and Safety Series ProPak Professional Cord and Safety Series ProPak Merchandise display unit Part No Merchandise display unit Part No DESCRIPTION ft. fluorescent light /3 50 ft. trouble light watt halogen light ft. 12/3 GFCI cord ft. GFCI duplex box /3 25 ft. trouble light Colored Cord ProPakTM Merchandise display unit 12/3 AWG Part No DESCRIPTION /3 2 ft. Tri-Source cord /3 25 ft. extension cord /3 2-1/2 inch in-line GFCI cord /3 50 ft. extension cord /3 50 ft. Tri-Source cord /3 100 ft. extension cord /3 100 ft. Tri-source cord /3 6 ft. Quadnector cord Canadian ProPak Merchandise display unit Most cartons have bilingual packaging All products CSA listed. Part No DESCRIPTION ft. lime/purple ft. hot pink/blue ft. green/orange ft. gray/red ft. blue/white ft. lime/purple Tri-Source ft. lime/purple Tri-Source ft. hot pink/blue Tri-Source DESCRIPTION /2 15 ft. hand held 13 watt fluorescent m Polar/Solar extension cord /3 15 m Polar/Solar extension cord /3 1 m in-line GFCI w/single female plug /3 8 m power plug GFCI w/single female plug /3 15 m Polar/Solar Tri-Source ext. cord /3 100 ft. Polar/Solar Tri-source cord 817

51 HVAC TOOLS NOTCHER Notcher blade is hot drop-forged of carbon steel. Cuts 31 V notch. Cuts clean without slippage. Compound leverage action. Heavy duty plastic grips for user comfort. Nominal Length Throat Depth Cutting Angle Cutting Capacity FCT-M-N1 8 in.204 mm 13/16 in.20 mm ga CR 5-BLADE CRIMPER This 5-Blade Crimper produces factory-precision indentations in stove pipe and round duct with just a squeeze. The compound-leverage mechanism, heavyduty jaw/handle linkage, and closing stop provide easy operation and consistent crimps for virtually leak-proof connections. The spring-actuated, narrow-opening handles are covered with blue vinyl grips and have carefully placed hand stops for extra comfort. Hardened steel construction and nickel plating provide long life and consistent crimp profile. Nominal Length Throat Depth Cutting Capacity FTC-M-C5 28 in.204 mm 1-1/4 in.30 mm 22 ga CR FTC-M-C5S 9.25 in.235 mm 1.25 in.32 mm 1 in.25 mm SEAMERS (straight/offset) Jaws are hot drop-forged of carbon steel. Bends and flattens soft sheet metal up to 22 gauge. Straight handle model and higher leverage offset handle model. Heavy duty plastic grips for user comfort. Jaw Nominal Length Depth Width Bending Capacity FCT-M-S1 8-1/4 in.209 mm 1-1/4 in.30 mm 3-1/6 in.78 mm 22 ga CR FCT-M-S2 8-1/4 in.209 mm 1-1/4 in.30 mm 3-1/6 in.78 mm 22 ga CR FCT-M-S6 8-1/4 in.209 mm 1-1/4 in.30 mm 6 in.152 mm 22 ga CR FCT-M-D1 Offset Duct Stretcher Aligns and pulls ductwork together easing installation of drive cleats. Offset handle protects hand. FCT-M-X1 Use to scribe a line or pierce and enlarge a hole in sheet metal duct. FCT-M-D1 FCT-M-X1 Nominal Length in mm 13 in mm FCT-M-F1 12-in. Folding Tool Use wide folding depth side for 1-in. folds and opposite narrow depth side for 3/8-in. folds. Nominal Length FOLD LENGTH CAPACITY FCT-M-F1 12 in mm (9.5 mm) SS FCT-M-F2 18-in. Folding Tool Use wide folding depth side for 1-in. folds and opposite narrow depth side for 3/8-in. folds. Nominal Length FOLD LENGTH CAPACITY FCT-M-F2 18 in mm (9.5 mm) SS FCT-M-L1 Sp Lock Punch Forged jaw punches impression on metal edge that fastens into opposite rolled metal edge for forming duct and pipe. Compound leverage handle action. Heavy duty plastic grips. Nominal Length Throat Depth CAPACITY FCT-M-L1 8 in mm 3/8 in mm 24 ga. CR FCT-M-T1 Tension Tool Handles all types of nylon ties including thin designs. Operate tension handles with one hand to tighten tie to desired tension. Use cutter handle to trim excess strap. DESCRIPTION Nominal Length FCT-M-T1 Snip-Replaceable Blade Castmag 8 in mm REPLACEABLE BLADES DESCRIPTION STD PCK QTY M1200 Snip-Replaceable Blade-Circulr 6 P107-D Snip-Replaceable Blade-Cut Str 6 P107-S Snip-Replaceable Blade-Circulr 6 P127-D Snip-Replaceable Blade-Cut Str 6 P127-S Snip-Replaceable Blade - 14 in. Comb 6 P147-C Snip-Replaceable Blade - 16 in. Bull 1 P167-B Snip-Replaceable Blade-Circulr 1 P77-D Snip-Replaceable Blade-Cut Str 6 P77-S -- 6 Utility Tools LIGHT METAL SNIP P657-N blades are hot drop-forged of high carbon steel. Self-opening with safety latch. Vinyl plastic coated handles. Excellent for reaching into tight ares or making intricate cuts. Ideal for a multitude of uses from roofing and sliding, to electricians, jewelers, hobbyists, and more. Nominal Length Pinch-to-Point Cut Length P657-N 6-1/2 in mm 1-1/4 in mm VINYL SIDING SNIP P127-SV blades are hot drop-forged of high carbon steel. Special hollow ground hand-stoned bevel edge for cutting vinyl siding and other soft materials. Specifically designed to cut through reinforced nail lip without crushing material. (Warning: Do not use to cut metal.) Nominal Length Pinch-to-Point Cut Length P127-SV 12 in mm 3 in mm 818

52 Utility Tools BY-PASS PRUNER/TACKBOARD SNIP OFFSET STRAIGHT CUT, OFFSET LEFT CUT, OFFSET RIGHT CUT AVIATION SNIPS P930 By-Pass blades are hot drop-forged of carbon steel and precision ground for a long lasting sharp cutting edge that will cleanly snip a delicate flower, prune a tender twig, or cut rigid carpet tackboard. Vinyl plastic coated grips provide user comfort and finger guard prevents hand slippage. Safety latched when not in use. Nominal Length Pinch-to-Point Cut Length P930 8 in mm 2 in mm UTILITY AVIATION SNIP P639 blades are stamped of high carbon steel and serrated to grip material being cut. Cuts straight or wide curves to left and right. Steel handles are plastic coated for user comfort. Nominal Length Pinch-to-Point Cut Length P639 9 in mm 1-1/4 in mm AVIATION SNIPS STRAIGHT CUT, LEFT CUT, RIGHT CUT AVIATION SNIPS These models are best suited for trim cutting soft sheet metal and for cutting a multitude of other materials. The P6716-S straight cut aviation snip is the most versatile of all aviation snip models. P6716-S straight cut aviation snip (cuts straight and wide curves to the left and right) P6716-L left cut aviation snip (cuts straight and tight curves to the left) P6716-R right cut aviation snip (cuts straight and tight curves to the right) Nominal Length Cutting Capacity Pinch-to-Point Cut Length P6716-S 9-3/4 in mm 18 ga CR - 22 ga ss 1-1/2 in mm P6716-L 9-3/4 in mm 18 ga CR - 22 ga ss 1-3/8 in mm P6716-R 9-3/4 in mm 18 ga CR - 22 ga ss 1-3/8 in mm These models are best suited for making long cuts through soft sheet metal and a multitude of other materials. The offset blade pattern guides the material being cut away from the blades. The offset blade pattern also positions the user s hand above the material being cut. P6510-S offset - straight cut aviation snip (cuts straight and wide curves to the left and right) P6510-L offset - left cut aviation snip (cuts straight and tight left curves) P6510-R offset - right cut aviation snip (cuts straight and tight right curves) Nominal Length Cutting Capacity Pinch-to-Point Cut Length P6510-S 9-3/4 in mm 18 ga CR - 22 ga ss 1-1/2 in mm P6510-L 9-3/4 in mm 18 ga CR - 22 ga ss 1-1/4 in mm P6510-R 9-3/4 in mm 18 ga CR - 22 ga ss 1-1/4 in mm LONG-CUT, BULLDOG/NOTCH CUT AVIATION SNIPS P6716-A long-cut aviation snip (3-inch length of cut) P6716-B bulldog/notch cut aviation snip(short straight cuts) P6716-A is best suited for long cuts through thin gauge material. The full 3-inch length of cut makes long cuts faster. P6716-B is best suited for cutting multiple thickness and rolled edges of sheet metal and up to 16 gauge soft sheet metal as well as other thick materials. Nominal Length Cutting Capacity Pinch-to-Point Cut Length P6716-A 11-1/2 in mm 20 ga CR - 24 ga ss 3 in mm P6716-B 9 in mm 16 ga CR - 18 ga ss 7/8 in mm SPECIAL LEFT CUT, SPECIAL RIGHT CUT AVIATION SNIPS These models are best suited for cutting extremely hard metals such as stainless steel, Inconel, Titanium, etc. Blades are specially heat-treated to a hardness of Rc and for this reason will out perform other models when used specifically to cut extremely hard materials. SSP6716-L special left cut aviation snip (cuts straight and tight left curves) SSP6716-R special right cut aviation snip (cuts straight and tight right curves) *CR = cold-rolled 16 ga = in. / sheet metal mm thickness SS = stainless 18 ga = in. / steel sheet metal mm thickness 20 ga = in. / mm thickness 22 ga = in. / mm thickness 24 ga = in. / mm thickness Nominal Length Cutting Capacity Pinch-to-Point Cut Length SSP6716-L 9-3/4 in mm 22 ga SS 1-3/8 in mm SSP6716-R 9-3/4 in mm 22 ga SS 1-3/8 in mm 819

53 AVIATION SNIPS THOMAS & BETTS CONDUIT CUTTER For cutting non-metal flexible conduit up to 1 inch. Replacement blade available also! XF-CUT XF-BLADE FOREARM FORKLIFT DESCRIPTION Conduit Cutter Conduit Cutter Replacement Blade ECONOMIC Costs less than other moving supplies like the hand truck or dolly. ERGONOMIC Encourages proper lifting techniques. EFFECTIVE Makes objects easier to grip and distributes weight making it easier to carry. ADJUSTABLE Up to 18 inches of adjustment to the height of the user and dimensions of the object. P TOTALINE REFRIGERANT SAFETY CAPS R-22 REFRIGERANT CAPS Totaline Refrigeration Safety Caps and Keys will assist to deter refrigeration theft. Once the cap is placed on the valve, a refrigeration thief will have a difficult time stealing without the key. We have seen in the news, the senseless tragedy that can occur due to refrigerant misuse. Totaline Safety Caps not only save refrigerant, they may save lives. Totaline Safety Caps are only available at Totaline stores. Store managers, be sure to promote this product to all of your dealers and contractors. They have probably already seen it out there and are waiting for it to hit the street. DESCRIPTION STD-PK-QTY P Totaline Safety Cap R-22, 2 Pc. 20 P Totaline Safety Cap R-22, 10 Pc. 10 P Totaline Safety Key R-22, 1 Pc. 20 R-410 REFRIGERANT CAPS Totaline Refrigeration Safety Caps and Keys will assist to deter refrigeration theft. Once the cap is placed on the valve, a refrigeration thief will have a difficult time stealing without the key. We have seen in the news, the senseless tragedy that can occur due to refrigerant misuse. Totaline Safety Caps not only save refrigerant, they may save lives. Totaline Safety Caps are only available at Totaline stores. Store managers, be sure to promote this product to all of your dealers and contractors. They have probably already seen it out there and are waiting for it to hit the street. DESCRIPTION STD-PK-QTY P Totaline Safety Cap R-410, 2 Pc. 20 P Totaline Safety Cap R-410, 10 Pc. 10 P Totaline Safety Key R-410, 1 Pc. 20 TOOLS-WELDING JW HARRIS DESCRIPTION STD-PK-QTY Stay-Clean Liq Flux, 4 oz Stay-Clean Liq Flux, 16 oz Stay-Clean Paste Flux, 4 oz HA Stay-Brite, 1# Spool Stay-Brite 8, 1# Spool Alsolder Kit Bridgit Lead-Free Solder Silver Solder Stay Silv 15/ Solder, Stay-Silv 0, 28 Sticks Stay Silv 2, 28 Sticks Stay-Silv White Flux, 7 oz Stay-Silv White Flux, 1# Stay-Silv 5/.050, 28 Stick Tube Flux Coated Blockade Blockade Brazing Kit Blockage, Silicone Braz g Alloy Stay-Silv 6/.050, 28-Stick Tube Square Brazing Rod 1/8 in Safety Silv 56-1 oz Safety Silv 56-3 oz Safety Silv 56-5 oz Safety Silv 45-1 oz Safety Silv 45-3 oz Safety Silv 45-5 oz Safety Silv 50-4 oz Dynaflow, 28-Stick Tube /50 Common Wire Solder Solder, 95/5 Common Wire /60 Common Wire Solder /40 Common Wire Solder 1 POL PZ-503 TORCH Self-igniting torches; burn FG-2, MAPP or propane gas PZ-503 had adjustable flame control. DESCRIPTION STD-PK-QTY Torch Kit 1 Oxygen Regulator 1 820

54 TOOLS-WELDING ESAB WELDING & CUTTING TOOLS DESCRIPTION STD-PK-QTY POL-16K09 1/2 in. Nozzle 1 POL-16K08 1/4 in. Nozzle 1 POL-SS9 360 Degree Swivel Braz g Torch 1 POL M Torch Handle 1 POL-09M Throttle Valve 1 POL-02X Torch Handle 1 POL-30X63 4-In-1 Outfit B 1 POL-30X64 4-In-1 Outfit MC 1 POL-30X60 5-In-1 Outfit B 1 POL-30X61 5-In-1 Outfit MC 1 POL-05L20 90 Degree Cut Attach 1 POL-16K Nozzle 1-1/2 in. 1 POL-119X07 Adapter 1 POL-19X41 Adapter MC-B 1 POL Adapter W POL-119X10 Adapter, Cyl/Reg 1 POL Air Gun 1 POL Basic B Kit W/Stand 1 POL Basic MC Kit w/stand 1 POL Brazing & Cutting Ki 1 POL Brazing & Cutting Ki 1 POL Brazing Outfit B 1 POL Brazing Outfit MC 1 POL Check Valve 1 POL Check Valve 1 POL Check Valve 1 POL Check Valve Flash Resistor 1 POL Cobra Attachment 1 POL Crystal 50 mm Plastic 1 POL-05Z93 Crystal Gauge R POL-92Z08 Disc 10 POL-150Z44 Disc Orifice No. 3 1 POL-150Z45 Disc Orifice No. 4 1 POL Disp. Cyl. Fg-2 48 POL-60F00 Disp. Cyl. Propane 48 POL-10X26 Extra Hvy No. 6 Tip 1 POL Filter Screw Assy 1 POL Fine No. 1A Tip 1 POL-790F37 Flints 10 POL-790F35 Friction Lighter 1 POL Gauge 1 POL Gauge 2 in. 100# 1 POL Gauge 2 in. 30# 1 POL Gauge 2 in. 400# 1 POL Gauge 2 in. 4000# 1 POL Gauge 2 Inc 600# 1 POL Gen. Maint. Kit B 1 POL Gen. Maint. Kit MC 1 POL-30X37 Gen. Purpose B 1 POL-30X38 Gen. Purpose MC 1 POL-06L54 Head 1 POL-11X19 Heat Shrink Tip 1 POL-10X25 Heavy No. 5 Tip 1 POL-791F80 Holder, Plastic 1 DESCRIPTION STD-PK-QTY POL-571F72 Hose 1 POL-571F73 Hose 1 POL-591F72 Hose 1 POL Kit, Welding 1 POL-10X23 Light No. 3 Tip 1 POL-790F98 Lighter Renewal 4 POL-90F50 Liquid Fuel Gas Hose 1 POL-10X24 Mediuim No. 4 Tip 1 POL-21X82 Melting Furnace 1 POL-NPK40TS Nitrogen Purge & Blow 1 POL Nitrogen Purge Kit 1 POL-NPK40S Nitrogen Purge w/stand 1 POL Nitrogen Reg 1 POL Nitrogen Reg 1 POL Nitrogen Regulator 1 POL-88F82 Nitrogen N/B-Tank Holder 1 POL-06L46 No. 1 Welding Head 1 POL-06L52 No. 15 Welding Head 1 POL-07L13 No. 15A Rosebud Torch 1 POL-06L47 No. 2 Welding Head 1 POL-07L15 No. 30 O-A Rosebud To 1 POL-06L48 No. 4 Welding Head 1 POL-06L49 No. 6 Welding Head 1 POL-06L50 No. 9 Welding Head 1 POL Nozzle 1 POL-12K15 Nut Conn. Weld 1 POL-14K07 O-Ring 375 ID 1 POL Oxygen Regulator 1 POL-60F28 Pencil Torch 1 POL-60F27 Pencil Torch Kit 1 POL-60F46 Pencil Torch Orifice 1 POL Precision Master O/F 1 POL Pressure Gauge 1 POL Presto Pak Brazing Kit w/tank 1 POL Presto Pak Maint. Kit w/tank 1 POL Presto Pak Maint. Kit w/tank 1 POL Presto Pak Precision Mstr W/Tnk 1 POL R Reg. 1 POL-04X36 R-411B Gauge 1 POL-04X37 R-411MC Gauge 1 POL-05X38 R-416A Gauge 1 POL R-511 LPG 1 POL R-511B 1 POL R-511MC 1 POL-30X66 Refrig. Outfit B 1 POL-30X67 Refrig. Outfit MC 1 POL-05X01 Regulator 1 POL-05X02 Regulator 1 POL Regulator 1 POL-60F34 Repl. Valve Unit 1 POL-19Z96 Repl. Fitting for Acetynne Reg. 1 POL Sabre V Brazing w/tote 1 POL Sabre V Light Duty Weld W/Tote 1 POL-31Z86 Safety Cap 1 POL Screen 1 POL Setting Regulator 1 POL Silver Smith Outfit 1 POL-790F34 Silver Flint Lighter 1 POL-501F12 Single Hose 12 ft. 1 POL-501F13 Single Hose 25 ft. 1 POL-501F11 Single Hose 6 ft. 1 POL Soapstone Hlder Assy 1 821

55 TOOLS-WELDING DESCRIPTION STD-PK-QTY POL-791F66 Soapstone Hldr Assy 72 POL-11X17 Soldering Iron 1 POL-11X18 Soldering Iron 1 POL Spec Fuel Outfit 1 POL-152Z37 Stand, Carry 1 POL Swirljet 1 POL Swirljet Kit 1 POL Swirljet SJ-3 A 1 POL Swirljet SJ-3 LPG 1 POL Swirljet SJ-4 LPG 1 POL Swirljet SJ-4 A 1 POL Swirljet SJ-5 A 1 POL Swirljet SJ-6 LPG 1 POL Tank Adapter 1 POL-25Y29 Tank B Handle 1 POL TFG-2 Torch Kit 1 POL-751F00 Tip Cleaner Set 1 POL-23S20 Tip Copper 1 POL-23S32 Tip Copper 1 POL-07L17 Torch 1 POL Torch Kit 1 POL Torch Kit 1 POL-60F26 Torch Kit 1 POL-PZ503 Torch Kit PZ503 1 POL-07L18 Torch Tip 1 POL-QWJ-2 Torch Tip 1 POL-QWJ-3 Torch Tip 1 POL-QWJ-4 Torch Tip 1 POL-QWJ-5 Torch Tip 1 POL-QWJ-6 Torch Tip 1 POL Torch W POL Tri-Flame Kit 1 POL Turbo-Tip Adapter 1 POL-92Z07 Washer 1 POL Wekding & Cutting Kit w/tank 1 POL-52Z68 Wrench 1 POL-505L00 Wrench B MC 1 POL X-3B Pol Kit 1 POL X-48 Pol Kit 1 POL X-5B Pol Kit 1 POL X-6MC Pol Kit 1 SPRING TUBE BENDER FOR 1/4 TO 7/8 Specially designed Yellow Jacket spring benders slip over soft copper and aluminum tubing during bending to help prevent tube collapse Silver plated finish Conforms to Fed. Spec. GGG- B- 191-a Type IV DESCRIPTION VENDOR UPC NO Spring Tube Bender Set - 6 sizes - 1/4, /16, 3/8. 7/16, 1/2 & 5/8 O.D Spring Tube Bender Set - 4 sizes - 1/4, 3/8, 1/2 & 5/8 O.D

56 FULL RANGE HEAVY DUTY TUBE BENDERS Make fast bends on almost every size of AC&R copper, brass, aluminum, teel and soft stainless steel tubing to 180 Benders feature special hardened wearing surfaces to help maintain accuracy They conform to Fed. Spec. GGG-B-191-a Type III, Class 2 A stationary hook holds tubing while bending Calibrated markings for bends up to 90 help you duplicate angles DESCRIPTION VENDOR UPC NO BENDING RADIUS /4, 5/16, 3/8 3-In-1 Tube bender / /8 Tube Bender / /2 Tube Bender /2 YELLOW JACKET HEX KEY WRENCHES All Yellow Jacket hex keys from.050 to 5/16 are premium 8650 heat treated steel alloy for rugged use Chamfered square end cuts for easy socket insertion Corrosion resistant finish Patented organizer case with identifying slots that lock keys in place when not in use Ball end keys ease tightening of fasteners where sockets are up to 30 off axis Ball end keys provide fast full socket engagement where regular hex keys cannot do the job Wrenches are 2.8 to 6.0 in length The most complete selection of L hex keys in the industry Heat treated for long life. Black finish 12 x 1-3/4 L shaped DESCRIPTION VENDOR UPC NO SET CONTAINS piece set Ball end Hex key wrenches , 1/16, 5/64, 3/32, 7/64,1/8, 9/64, 5/32, 3/16, 7/32 1/4, 5/16 & Organizer Case piece set Std. end Hex key wrenches /64, 3/32, 1/8, 5/32, 3/16, 7/32, & 1/4 KNUCKLE-SAVER HEX WRENCH SETS The unique offset design of these Yellow Jacket wrenches save your knuckles in tight places Accurately sized and broached ends for correct fit Heat treated critical wear parts for long life Finger control reversing Chrome plated for durability Available in sets of 3 or 5 wrenches DESCRIPTION VENDOR UPC NO HEX SIZES Setof5KnuckleSaverHexWrenches /4-7/ Setof3KnucklesaverHexWrenches /4-9/16 SERVICE WRENCHES: STRAIGHT Standard reversible ratchet wrench with square openings 1/4 and 3/16 at one end; 3/8 and 5/16 at other end SERVICE WRENCHES: HEAVY DUTY Heavy duty version of original straight service wrench Has heavier handle and larger gear Stronger gear teeth are combined with strong reversing mechanism for long life Square opening 3/16 and 1/4 at one end; 3/8 and 5/16 at other end 823

57 SERVICE WRENCHES: OFFSET Knuckle Saver design for convenience in tight areas Square opening 1/4 and 3/16 at one end, 3/8 and 5/16 at other end DESCRIPTION VENDOR UPC NO Straight Service Wrench Heavy Duty Straight Service Wrench Offset - Knuckle Saver - Service Wrench FINFIX FIN COMBS DESCRIPTION VENDOR UPC NO FinFix No. 7 Comb - 21/22 and 23/24 FPI FinFix Fin Comb 6 piece set (Includes: 8 & 10, 9 &15,11 & 13, 12 & 14, 16 & 17, 18 & 20 FPI Combs) FLAME INSPECTION MIRRORS Check flame, serial numbers and leaks in hard to see places Stainless steel mirror on ball joint rotates 360 Handle telescopes to 28 DESCRIPTION VENDOR UPC NO Round Inspection Mirror, 3-3/4 dia Rectangular Inspection Mirror, 2 x 1-1/ WORM GEAR HOSE CLAMPS Clamps are in boxes of 10a YELLOW JACKET GAS TEST GAUGE Easy to read gauge to test system pressure for leaks in new installations Helps meet inspection codes Pressure drop on gauge indicates leakage Available to go on 3/4 pipe end Improved brass bell DESCRIPTION VENDOR UPC NO lb. Test Pressure Gauge with 3/4 Pipe End YELLOW JACKET GAS PRESSURE TEST KIT Easier to use than a manometer Compact kit helps you accurately set manifold pressure for natural or L.P. gas Economical unit with high value features Sensitive diaphragm gauge calibrated in inches water column Tube nibble for easy connection to system manifold Two gauge ranges available: 0-35 and 0-10 water column DESCRIPTION VENDOR UPC NO W.C. Complete Pressure Test Kit W.C. Barb Fitting Pressure Test Gauge W.C. Complete Pressure Test Kit

58 YELLOW JACKET WATER TYPE MANOMETER Economical plastic tube manometer helps you set manifold pressure for natural or L.P. gas Now goes to -2 W.C. for newer systems Strong magnet on manometer holds it in convenient upright position Includes connecting tubing with fitting DESCRIPTION VENDOR UPC NO W.C. Scale manometer w/ tubing & fitting YELLOW JACKET SLING PSYCHROMETER Slim, compact tool easily checks Wet and Dry Bulb temperatures and humidity One piece unit with self contained housing fits into your pocket Calibrated and easy to read DESCRIPTION VENDOR UPC NO Sling Psychrometer YELLOW JACKET SUPERHEAT CALCULATION KIT With the access valve, digital thermometer, and core extractor tool, you can easily take an internal temperature reading for calculating superheat. Take internal refrigerant temperature readings from -58 F to 302 F and pressure reading for calculating superheat. Remove broken Schrader core Extracts Schrader core without opening the system Chases damaged threads Replaces cores Use as a recovery valve Uses a vacuum valve to increase flow and reduce vacuum time Taking a reading is as simple as: 1. Attach valve to system 2. Extract core with tool - shut off side valve 3. Insert Thermometer and attach gauges to take readings 4. Add or remove gas per approved methods 5. Remove thermometer and replace core DESCRIPTION VENDOR UPC NO Complete Superheat Kit and Accessories Using valve YELLOW JACKET FLUORESCENT LEAK SCANNER SYSTEM II Complete system includes: UL listed UV lightgun with bulb, hand grip and heat guard. 110 volt. Mineral-based pre-filled fluorescent solution tubes with two bleed valves. SealRight Fitting immediately traps refrigerant in hose when disconnected. UV-absorbing anti-fogging goggles. Service manual and carrying case. DESCRIPTION VENDOR UPC NO Leak Scanner System II complete 120V Leak Scanner System II complete 230V YELLOW JACKET MICRO LED UV LEAK DETECTION KITS Enables you to accurately pinpoint every leak at the speed of light Find previously undetected leaks Easy to use with all AC&R systems and refrigerants Illuminates 120 ft away with 5 high intensity clear bulbs DESCRIPTION VENDOR UPC NO Micro UV LED and Dye Kit for ACR

59 YELLOW JACKET SUPEREVAC PUMPS The SuperEvac system pulls a fast vacuum to 15 microns and better Fast - gives you more time for more calls, and 15 microns or better is high enough to get rid of contaminants that could cause system failures Low profile switch to avoid breakage Internal motor overload Anti-backflow valve Replaceable two stage vacuum cartridge Wide view sight glass for easier monitoring of oil level 8' power cord with motor mounted switch Gas ballast speeds evacuation and keeps oil cleaner Intake includes 1/4" and 1/2" male flare fittings Protected blank-off valve to isolate pump from the system Heavy duty handle is permanently attached to pump body; built in lift hook hole Longer heat dissipation fins for a cooler running unit Wide mouth oil reservoir port for easier, neater filling - it doubles as a pump exhaust Two stage rotary vane design increases efficiency and speeds pump down to 15 microns Vacuum indicator gauge at the pump intake fitting shows evacuation progress down to the green 29" to 30" range, so you'll know when to turn on electronic gauge for more precise readings DESCRIPTION VENDOR UPC NO VOLTS HP-RPM OIL CAPACITY CFM Vacuum Pump /1/60 1/ OZ CFM Vacuum Pump /1/60 1/ OZ CFM Vacuum pump /1/60 1/ OZ. DIGITAL LCD VACUUM GAUGE Unique thermal conductivity sensor automatically compensates for temperature with no calibration Readings from 25 to 100,000 microns DESCRIPTION VENDOR UPC NO Digital LCD Vacuum gauge w/battery, hook, case SuperEvac LCD vacuum gauge complete in case Adapter brass coupler Replacement sensor for 69070, SuperEvac LCD vacuum gauge full range complete in case Optional ball valve to add to sensor 1/8 in. FPT x 1/4 in.female flare Vibration isolation hose Optional coupler to add to sensor 1/8 in. FPT x 1/4 in.female flare YELLOW JACKET VACUUM PUMP OIL Specially refined and formulated for extremely low vapor pressure and high pump efficiency at all temperature conditions Container has attached heavy duty funnel dispenser DESCRIPTION VENDOR UPC NO Quart of Vacuum Oil - 12 per case Gallon of Vacuum Oil - 4 per case

60 YELLOW JACKET RATCHET HAND BENDER Easy one hand bending of 3/8 in. to 7/8 in. soft copper Bending shoes change quickly DESCRIPTION VENDOR UPC NO Complete Kit /8 in. O.D. Bending Mandrel /2 in. O.D. Bending Mandrel /8 in. O.D. Bending Mandrel /4 in. O.D. Bending Mandrel /8 in. O.D. Bending Mandrel Crossbar Assembly Steel Case with Inserts Reverse Bending Kit YELLOW JACKET TUBING EXPANDER/SWAGER Precise swaging on the job Can easily expand 5/16 in. to 1-5/8 in. O.D. tubing DESCRIPTION VENDOR UPC NO Expander Kit with handles; Heads for 3/8 in., 1/2 in., 5/8 in., 3/4 in., 7/8 in., 1-1/8 in. tubing O.D., deburing tool, steel carrying case, instructions YELLOW JACKET SERIES 41 MANIFOLDS Large bold numbers and colored scales are easy to read Removable Lexan crystals resist breakage Standard gauges are color coded red (high pressure) and blue (low pressure) Every manifold is individually pressure tested for reliability before shipping Forged solid brass body with metal valve handles for durability Metal handles are full size for easy operation Hose anchors are forged into back of body at 45 angle Full porting maximizes capacity Sliding double "O" ring piston Non rotating design reduces wear Long life nylon seat is also for vacuum Only 1-1/2 turns give you full flow Surge protector helps minimize needle pulsation for easier, more accurate readings Limited Lifetime Warranty on manifold with valves - see manifold instructions for details Manifolds with hoses include color coded Yellow Jacket charging hoses with 500 PSI working pressure and all the other performance features you've come to expect Plus II hose assemblies are UL recognized to 4000 psi burst 800 psi working DESCRIPTION VENDOR UPC NO GAUGE SCALES Manifold, Red & Blue gauges, hook, anchors and 36 R,Y,B HA original hoses R-12, R-22, R Manifold, Red & Blue gauges, hook & anchors without hoses R-12, R-22, R Manifold, Red & Blue gauge, hook, anchors and 60 R,Y,B, HA original hoses R-12, R-22, R Manifold, Red & Blue gauges, hook, anchors & 60 R,Y,B, Plus II hoses w/ SealRight fitting R-12, R-22, R Manifold, Red & Blue gauges,hook & anchors without hose R-134a, R-404a, R Manifold, Red & Blue gauges, hook & anchors & 60 in. R4B Plus II hoses w/seal right fitting R410A 827

61 YELLOW JACKET BRUTE TEST/CHARGING MANIFOLDS With full 3/8" bore all the way through the aluminum block, the new Brute Test/Charging Manifolds are engineered to dramatically increase flow over conventional four and two valve designs Increased flow saves time for charging, vacuum and recovery The Brute Series also combines new design features with other features proven in the Yellow Jacket Series 41 Manifolds Valves use proven piston/double "O" ring design for reliability and long service life. Precision machined aluminum alloy body is lightweight for handling ease, and heavy duty for rugged on the job use. Color coded handles are made from Lexan and spaced for large hands. Slip resistant handle design gives a surer grip even to oily fingers. Swivel hook threads directly into the bar to resist pull out. Optical sight glass aids refrigerant inspection while charging refrigerants, and during recovery. Valves are front mounted for fast, easy access. All 2-1/2" gauge Brute manifolds include gauge boots for protection. DESCRIPTION VENDOR UPC NO GAUGE SCALES VACUUM PORT HI & LO PORTS Manifold, and 60 R,Y,B Plus II hoses & 3/8 B R-12, R-22, R-502 3/8 1/ Manifold, and 60 R,Y,B Plus II hoses & 3/8 B R410A 3/8 1/4 FAHRENHEIT PRESSURE & COMPOUND GAUGES - PSI Yellow Jacket replacement gauges for manifolds Manifold dials for R-12, R-22, R-502, and R-410A scales Flutterless Technology, surge protector minimizes the needle pulsation for improved accuracy Bold high visibility dials with colored temperature scales for easy reading Compound gauges have over pressure protection to 350 PSIG on R-12, R-22, R-502 models 1/8" Male pipe thread (MPT) lower mount fitting Compound gauges have over pressure protection to 500 PSIG and R-410A models DESCRIPTION GAUGE SCALES High Side Pressure Gauge (Red) PSIG R-12, R-22, R Low Side Compound Gauge (Blue) PSIG w/ 350 PSIG retard R-12, R-22, R High Side Pressure Gauge PSIG R410A Low Side Compound Gauge 30 in PSIG w/500 PSIG retard R410A LARGE FAHRENHEIT PRESSURE & COMPOUND GAUGES PSI Yellow Jacket replacement gauges for manifolds Manifold dials for R-12, R-22, R-502, and R-410A scales Flutterless Technology, Surge Protector minimizes the needle pulsation for improved accuracy High visibility 3-1/8 in. dials with colored temperature sales for easy reading Gauge is calibrated to Class I 1% accuracy 1/8 in. MPT lower mount fitting DESCRIPTION VENDOR UPC NO GAUGE SCALES High side pressure gauge 3-1/8 in. dial, PSIG R-12, R-22, R Low side pressure gauge 3-1/8 in. dial, 30 in PSI w/350 PSI retard R-12, R-22, R S High side pressure gauge 3-1/8 in. dial, PSIG R410A Low side pressure gauge 3-1/8 in. dial, 30 in PSI w/500 PSI retard R410A MAGNI-FOLD Magnetic Mounting Bracket for charging manifolds Provides a quick, convenient method of affixing your charging manifolds to any appropriate metal surface Magni-Fold's super strong magnet will hold the charging manifold firmly in place Manifold will not fall, slip or slide Eliminates falling manifolds, scratched lenses, or gauges twisting out of view MODEL NO VENDOR APPLICATION MF-1 MF-1 Ritchie - All Series 41 Robinair , 41155, J/B - M2F Series MF-2 MF-2 Robinair , 54, 55, 56 Ritchie Uniweld - 100QALH 828

62 YELLOW JACKET HOSES Original 1/4" Premium Charging Hoses Widely accepted by industry professionals for all weather flexibility and dependability Replaceable gaskets that do not blow out with normal day-in, day-out use Six sided crimping used and performance proven since the early 60's Date coded with year of manufacture to help in our safety program management Full size brass nuts for easier tightening and longer life Adjust-A-Valve Opener allows you to easily open all troublesome out of tolerance Schrader valves Blow-off groove channels refrigerant out of the front of the nut to help prevent spray back Hose cover pin-pricked to resist bubbling and bursting Assorted lengths in yellow, red, and blue for easy hook up identification 1/4" straight X 1/4" 45 angle fitting DESCRIPTION LENGTH VENDOR UPC NO Pack 36 Premium 1/4 Hoses (Red, Yellow, Blue) Pack 60 Premium 1/4 Hoses (Red, Yellow, Blue) Pack 72 Premium 1/4 Hoses (Red, Yellow, Blue) YELLOW JACKET PLUS II HOSE ASSEMBLIES Plus II 1/4" Charging Hoses Same proven performance features of the Premium Charging Hose noted above, plus more Moisture barrier provides improved resistance to moisture migration Available with SealRight or NEW component ball valve ends Immediately traps refrigerant in the hose when disconnected, helps meet no venting requirements 45 end for ease in tight areas Gaskets resist deterioration from existing CFC's, plus new HFC refrigerants and oils Plus II hose assemblies are UL recognized to 4000 PSI burst, 800 PSI working pressures for R410A DESCRIPTION LENGTH VENDOR UPC NO Pack 60 Plus II 1/4 R,Y,B Hoses w/ standard 1/4 fittings Pack 36 Plus II 1/4 R,Y,B Hoses w/ 45 SealRight fitting at 1 end Pack 60 Plus II 1/4 R,Y,B Hoses w/ 45 SealRightfitting at 1 end YELLOW JACKET 3/8 PLUS II B CHARGING HOSES Special design puts Yellow Jacket features in a larger volume 5/16" I.D. hose. Working pressure 600 psi; burst rating 3000 psi. Lengths available up to 100 ft. DESCRIPTION COLOR CODE LENGTH VENDOR UPC NO /8 Fl. Str. x 3/8 Fl. Str. Yellow /8 Fl. Str. x 3/8 Fl. Str. Blue /8 Fl. Str. x 3/8 Fl. Str. Red /8 Fl. Str. x 3/8 Fl. Str. Yellow /8 Fl. Str. x 3/8 Fl. Str. Blue /8 Fl. Str. x 3/8 Fl. Str. Red /8 Fl. Str. x 3/8 Fl. Str. Yellow /8 Fl. Str. x 3/8 Fl. Str. Blue /8 Fl. Str. x 3/8 Fl. Str. Red /8 Fl. Str. x 3/8 Fl. Str. Yellow /8 Fl. Str. x 3/8 Fl. Str. Blue /8 Fl. Str. x 3/8 Fl. Str. Red SERVICE PARTS DESCRIPTION VENDOR UPC NO Set of gauge boots (1 red & 1 blue) slip around standard /2 gauges to protect from damage Set of 2 Handle Screws and Washers (For series 41)

63 6 FLEXFLOW ADAPTER HOSES Easy retrofit of existing Plus II hoses with FlexFlow capabilities Valve handle position shows when the valve is opened, closed or anywhere between Zero restriction for maximum flow-ideal for use in recovery Flexible hose between valve and fitting for handling in tight areas DESCRIPTION LENGTH VENDOR UPC NO Pack FreeFlow Adapter hoses (includes 1/4 yellow, 1/4 blue and 1/4 red FlexFlow adapter) YELLOW JACKET(QC) QUICK COUPLERS Couplers are full size with deep knurling for easy handling Acme conversion couplers aid in recovery where recovery tank has incompatible threads DESCRIPTION VENDOR UPC NO /4 female QC x 1/4 male flare /2 Acme female x 1/4 male flare SEALRIGHT QUICK COUPLERS Innovative SealRight fittings automatically and immediately trap refrigerant in the hose when disconnected Helps meet non venting regulations and prevent finger burns One piece attaches quickly, saving time compared to 2 piece quick couplers Gaskets resist deterioration from existing CFC s, HCFC s, and new 134A refrigerant and oils. Couplers are field serviceable with available replacement parts Not reconmmended for R410A. DESCRIPTION VENDOR UPC NO /4 SealRight Straight x 1/4 male flare /4 SealRight 45 x 1/4 male flare Set of 2 (includes: 1/4 SealRight Straight x 1/4 male flare & 1/4 SealRight 90 x 1/4 male flare) Repair Kit with: Pkg of 10 O Rings (1), Plug Assembly with all seals (2), Nut and Clip (3) QUICK COUPLER GASKETS The only gasket designed for optimum performance with Yellow Jacket Charging Hoses Works with all refrigerants. Manufactured to strict tolerances to resist blow out. DESCRIPTION VENDOR UPC NO QTY PER PACK /4 Hose Gaskets (10 Pack) /8 Hose Gaskets (10 Pack) /2-5/8 Hose Gaskets (10 Pack) BALL VALVE 4 IN 1 VACUUM/CHARGE VALVE & CORE TOOL This versatile tool for the low or high side of a system does four jobs: Vacuum valve - extra 1/4 side port to attach electronic micron vacuum gauge right at system Core removal access - enables you to evacuate and charge through an unrestricted line Core replacement Recovery valve - core removal allows recovery unit to work at maximum efficiency, speeding the recovery process DESCRIPTION VENDOR UPC NO Vacuum charge ball valve

64 GAS RETENTION VALVE Sturdy valve controls refrigerant flow from access fitting Closes Schrader before disconnecting New back seat valve feature to retain gas in hose when disconnecting DESCRIPTION VENDOR UPC NO Gas Retention (Control) Valve YELLOW JACKET PREMIUM TUBE CUTTERS Enclosed precision feed mechanism for easy, smooth cutting Wide rollers with flare cut-off groove for convenience Wheel recessed into cutter body to save 1 in cutting radius Sharp cutting wheel edge for less burr on copper, aluminum and mild steel tubing Wheel is pinned rather than screwed in position, so it rotates in either direction without the screw backing out. Handle screwed onto body for durability rather than riveted Improved feed screw mechanism now moves better than ever Spare wheel attached Corrosion resistant finish on lightweight aluminum frame Retractable reamer Fold away tool steel reamer with turned cutting edge removes inside burrs cleanly Filing surface on reamer removes outside burrs DESCRIPTION CAPACITY VENDOR UPC NO SmallTube Cutter 1/8 to 1-1/8 O.D LargeTube Cutter 1/4 to 1-5/8 O.D HeavyDutyTubeCutter 3/8 to 2-5/8 O.D

65 BRUTE II Test & Charging Manifold - F The new BRUTE II 4-Valve Test and Charging Manifold is the first large bore forged aluminum manifold in the industry. It has been trimmed down for lighter weight but with the same powerful performance of the original model. The streamlined BRUTE II continues to provide the flow that's proven faster than any conventional manifold. And even though sleeker and more compact, the aluminum alloy is forged for strength and reliability with 3/8" bores through the body to speed the job Fourth hose enables connection to hi/lo sides, refrigerant tank, and recovery unit or vacuum pump for diagnostics, evacuation and charging without switching hoses. 1/4" hi/lo sides with 3/8 vacuum port for regular jobs, or; 3/8" hi/lo sides with 1/2 vacuum port for larger systems. Large, easy-to-read 3-1/8 (80 mm) red and blue steel case, 1% accuracy (Class 1) gauges with protective boots; front access for easy field recalibration. Proven, double O -ring piston for reliability and long service life. Exclusive 100-mesh filter in-line on all flare fittings helps keep out particulate material and extends the life of the seat. Contoured easy-grip handles for positive control; color coded for ready identification. Sight glass to easily view refrigerant movement and condition during charging and recovery. Heavy-duty hook won t pull out. Also available with YELLOW JACKET 3-1/8" (80 mm) red and blue liquid-filled gauges. 832

66 BRUTE II Test & Charging Manifold - F BRUTE II 4-Valve Manifolds 3-1/8 (80 mm) F Gauges Steel Case (with protective gauge opts) or Liquid-Filled New UPC # Vac. Port Hi, Lo Charge Gauge Hoses Discontinued BRUTE UPC # R-410A R-22 R- 404A R- 410A R-12, R- 22, R- 502 BRUTE II 4-VALVE with 3/8 Vacuum Port /8 1/4 Red/Blue Manifold Only /8 1/4 Liquid Manifold Only /8 1/4 Red/Blue 60 Plus II Compact Ball Valve - RYB & 3/8 x 45 n/a /8 1/4 Red/Blue Manifold Only n/a /8 1/4 Liquid Manifold Only n/a /8 1/4 Red/Blue 60 Plus II Compact Ball Valve - RYB & 3/8 x 45 n/a /8 1/4 Red/Blue Manifold Only /8 1/4 Liquid Manifold Only /8 1/4 Red/Blue 60 Plus II RYB & 3/8 x 45 n/a /8 1/4 Liquid 72 Plus II RYB & 3/8 x BRUTE II 4-VALVE COMMERCIAL with increased capacity larger ports /8 3/8 Red/Blue Manifold Only n/a /2 3/8 Liquid Manifold Only R-134a R-404A R-407C R-22, R- 134a, R- 404A /8 3/8 Red/Blue 3/8 x 60 Heavy Duty - Str. x 45 n/a /2 3/8 Liquid BRUTE II 4-VALVE with 3/8 Vacuum Port 3/8 x 60 Heavy Duty - Str. x 45 1/2 x 60 Heavy Duty - Str. x Str /8 1/4 Red/Blue Manifold Only n/a /8 1/4 Liquid Manifold Only n/a /8 1/4 Red/Blue 60 Plus II RYB & 3/8 x 45 n/a /8 1/4 Liquid 72 Plus II RYB & 3/8 x 45 n/a BRUTE II 4-VALVE with 3/8 Vacuum Port /8 1/4 Red/Blue Manifold Only n/a /8 1/4 Liquid Manifold Only n/a /8 1/4 Red/Blue 60 Plus II RYB & 3/8 x 45 n/a /8 1/4 Red/Blue 60 Plus II Compact Ball Valve - RYB & 3/8 x 45 n/a /8 1/4 Liquid 72 Plus II RYB & 3/8 x 45 n/a BRUTE II 4-VALVE COMMERCIAL with increased capacity larger ports /8 3/8 Red/Blue Manifold Only n/a /2 3/8 Liquid Manifold Only n/a /8 3/8 Red/Blue 3/8 x 60 Heavy Duty - Str. x 45 n/a /2 3/8 Liquid 3/8 x 60 Heavy Duty - Str. x 45 1/2 x 60 Heavy Duty - Str. x Str n/a 833

67 TITAN Test & Charging Manifold - F Forged aluminum alloy body provides increased strength and reliability... Designed for A/C, Refrigeration and Automotive Technicians The new TITAN Test and Charging Manifold is the first forged aluminum manifold in the industry. The special aluminum alloy construction of the manifold body makes it lightweight for handling ease with the durability and reliability required for repeated, rugged use. Features/Benefits of 2- and 4-Valve Models Large, easy-to-read 3-1/8 (80 mm) steel case red and blue, 1% accuracy (Class 1) gauges; front access for easy field recalibration; optional protective gauge boots available. Proven, double O -ring piston for reliability and long service life. Exclusive 100 mesh filter in-line on all flare fittings helps keep out particulate material and extends the life of the seats. Contoured easy-grip handles for positive control; color coded for ready identification. Sight glass to easily view refrigerant movement and condition during charging and recovery. Heavy duty hook won t pull out. Additional Features/Benefits of 4-Valve Model: Fourth hose to enable connection to hi/lo sides, refrigerant tank, and recovery unit or vacuum pump for diagnostics, evacuation and charging without switching hoses. 3/8" vacuum port for use with larger hose to cut evacuation time by up to 33% (all other fittings on unit are 1/4"). Also available with YELLOW JACKET 3-1/8 (80 mm) red and blue liquid-filled gauges. 834

68 TITAN Test & Charging Manifold - F TITAN 2-VALVE MANIFOLDS w/ sight glass 3-1/8 (80 mm) -1% Accuracy Steel Case - F Gauges R-410A R-22 R- 404A R- 410A R-12R- 22 R- 502 New UPC# Gauges Hoses Red/Blue No hose Red/Blue 60 Plus II -RYB Red/Blue 60 Plus II Compact Ball Valve -RYB Red/Blue No hose n/a Red/Blue 60 Plus II -RYB n/a Red/Blue 60 Plus II Compact Ball Valve -RYB n/a Red/Blue No hose Red/Blue 60 Plus II -RYB Red/Blue 60 Plus II SealRight -RYB Red/Blue No hose R-134a R-404A Red/Blue 60 Plus II -RYB R-407C Red/Blue 60 Plus II SealRight -RYB Red/Blue No hose n/a R-22 R- 134a R Red/Blue 60 Plus II -RYB n/a 404A Red/Blue 60 Plus II SealRight -RYB n/a Discontinued Bantam UPC # TITAN 4-VALVE MANIFOLDS w/ sight glass 3-1/8 (80 mm) -1% Accuracy - Steel Case or Liquid F Gauges R- 410A UPC# Gauges Hoses Replaces Bantam Part # Red/Blue No hose Liquid No hose Red/Blue 60 Plus II Compact Ball Valve -RYB & 3/8 x Red/Blue 60 Plus II -RYB & 3/8 x Red/Blue No hose n/a R Red/Blue 60 Plus II -RYB & 3/8 x 45 n/a R Red/Blue 60 Plus II Compact Ball Valve -RYB & 3/8 x 45 n/a 404A R Liquid No hose n/a 410A Liquid 60 Plus II -RYB & 3/8 x 45 n/a R- 12R- 22 R Red/Blue No hose Red/Blue 60 Plus II -RYB & 3/8 x Liquid No hose Liquid 60 Plus II -RYB & 3/8 x R Red/Blue No hose a R Red/Blue 60 Plus II -RYB & 3/8 x A Liquid No hose R- 407C Liquid 60 Plus II -RYB & 3/8 x R Red/Blue No hose n/a R Red/Blue 60 Plus II -RYB & 3/8 x 45 n/a 134a R Liquid No hose n/a 404A Liquid 60 Plus II -RYB & 3/8 x 45 n/a 835

69 IMPERIAL TUBE CUTTERS JUNIOR TUBE CUTTER IMP-227-FA DESCRIPTION For 1/8" to 3/4" (4 to 19 mm) O.D. tubing, (1/8" to 5/8" nom.). Enclosed feed mechanism. Length: 3-1/2" Weight: 5 oz. IMPERIAL TUBE BENDERS, LEVER TYPE IMP-260-FHA For soft copper, aluminum, brass, steel, and other metal tubing Quickly adapts to all sizes in its range Long handles reposition during bend for best leverage Calibrations show precise bend angle One piece benders furnished for 1/4 and 5/16 O.D. tube sizes. TUBE O.D. (in.) NOMINAL SIZE (in.) IMP-260-FHA IMP-350-FHA IMP-360-FHA RADIUS TO CENTER OF TUBE (in.) 1/4 1/8 9/16 5/16 11/16 3/8* 1/4 1-5/8 1/2* 3/8 1-5/8 5/8* 1/2 2-1/4 3/4* 5/8 3 7/8* 3/4 3 1/4 1/8 9/16 5/16 11/16 3/8* 1/4 1-5/8 1/2* 3/8 1-5/8 5/8* 1/2 2-1/4 3/4* 5/8 3 3/8* 1/4 1-5/8 1/2* 3/8 1-5/8 5/8* 1/2 2-1/4 3/4* 5/8 3 TOTAL KIT WEIGHT (lbs) IMP-260-FHA *Recommended for bending annealed copper and aluminum tubing only. IMPERIAL TUBE CUTTERS HI-DUTY TUBE CUTTERS Rollers have flare cut-off groove, fold away reamer and spare cutting wheel. IMP-TC-1000, IMP-TC-1000SP IMP-312-FC, IMP-312-FCSP IMP-TC-1020 IMP IMP DESCRIPTION For 1/8" to 1-1/8" (4 to 28 mm) O.D. tubing, (1/8" to 1" nom.). Length: 4-15/16" Weight: 6-1/2 oz. For 1/4" to 1-5/8" (7 to 41 mm) O.D. tubing, (1/8" to 1-1/2" nom.). Length: 5-1/2" Weight: 7 oz. Combination tube constrictor and cutter for 1/8" to 1-1/8" (4 to 28 mm) O.D. tubing. Includes roller for making brazed connections. Cutter wheel for stainless steel and hard temper tubing Constrictor roller 836

70 IMPERIAL TUBE CUTTERS ADJUST-O-MATIC TUBE CUTTERS Ratchet feed mechanism speeds up cutting operation. Extra wide rollers stabilize tubing. Spare cutting wheel included. DESCRIPTION IMP-206-FB For 3/8" to 2-5/8" (10 to 66 mm) O.D. tubing, (1/4" to 2-1/2"nom.). Length (closed): 7-3/4" Weight: 2 lbs IMP-406-FA Hi-Duty 2" to 4" cutter for 2" to 4-1/8" (51 to 104 mm) O.D.tubing, (2" to 4" nom.). Length (closed): 11-1/4" Weight: 3-1/2 lbs. IMP TUBE CUTTERS BIG-IMP TUBE CUTTERS. IMP-TC-1050 IMP-TC-1050SP IMP-TC-2050 IMP-TC-2050SP DESCRIPTION For 1/8 to 5/8 (4 to 15 mm) O.D. tubing, (1/8 to 1/2" nom.). Requires only 1-1/4 swing radius. (Requires only 1-3/8 swing radius with 5/8 tube.) Repositioned rollers to bottom of tool allows for easier cutter engagement on tubing. Enclosed feed-screw minimizes contamination, assuring continued free operation. Redesigned feed mechanism improves overall cutting action. Size: 1-3/4 x1-1/4 x1/2 Weight: 2-1/2 oz. For 3/16 to 7/8 (5 to 22 mm) O.D. tubing. (Requires only 1-11/16 swing radius.) IMP-174-F, IMP-174-FSP DESCRIPTION For 3/8" to 1-1/8" (10 to 28 mm) O.D. tubing, (1/4" to 1" nom.). Requires only 1-15/16" swing radius. (Requires only 2-1/4" swing radius with 1-1/8" tube.) Size: 2-11/16" x 2-1/32" x 1-1/8" Weight: 5 oz. *SP = Skin Packaged 837

71 IMPERIAL TUBE BENDERS, LEVER TYPE SINGLE SIZE TUBE BENDERS Each tool bends one size. Open size design slips over tube at any point. Makes smooth short radius bends up to 180.Calibrated to show angle of bend.wide hook grips tubing securely. New fixed hook tube benders furnished for 1/4 to 1/2 O.D. size have easy 90 start. BENDING RANGE TUBE OD (in) NOMINAL SIZE (in) RADIUS to CENTER of TUBE (in) WEIGHT (lbs) IMP-364-FH-02 1/8 -- 3/8 1/2 IMP-364-FH-03 3/ /16 1/2 IMP-364-FHA-04 1/4 1/8 9/16 1 IMP-364-FHB-04 1/4* 1/8 9/16 1 IMP-364-FHA-05 5/ /16 1-1/8 IMP-364-FHB-05 5/16* -- 11/16 1-1/8 IMP-364-FHA-06 3/8 1/4 15/16 1-3/4 IMP-364-FHB-06 3/8* 1/4 15/16 1-3/4 IMP-364-FHA-07 7/ /2 3-1/2 IMP-364-FHB-07 7/16* /2 3-1/2 IMP-364-FHA-08 1/2 3/8 1-1/2 3-1/2 IMP-364-FHB-08 1/2* 3/8 1-1/2 3-1/2 IMP-364-FHA-10 5/8** 1/2 2-1/4 5-1/2 IMP-364-FHA-12 3/4** 5/8 3 7 IMP-364-FHA-14 7/8** 3/ /2 IMP-364-FHA-16 1** /2 10-1/2 IMP Form shoe furnished for 1" tube bender. Swivel handle may be repositioned to regain leverage for bends greater than 90, eliminating bender twisting and handle crossing. Enclosed swivel mechanism provides extended life. Ideal for bending stainless steel, as well as other tubing. **For bending annealed copper and aluminum tubing only. RATCHET WRENCHES FOR REFRIGERATION/AIR CONDITIONING SERVICE DESCRIPTION Steel forged. For use on small refrigerant cylinders, shut-off valves, packing glad wrenches, etc.ratchet has 1/4" square drive and raised face. Handle has 3/16 and 1/4 square drives and 1/2 hex.. IMP-123-C DESCRIPTION Combination wrench with the four sizes most needed for servicing automotive air conditioning: 9/16 hex for dust cap on Schrader type valves and plug oil check on York compressor 1/2 hex for mounting bolts on Tecumseh, York, and Airtemp compressors. 1/4 square for valve stem on York and Tecumseh service valves and old style compressor valves 3/16 square for valve on old style refrigerant charging tanks.. IMP-124-C DESCRIPTION Rugged, steel forged wrench with four sizes covering almost any application. 1/4 square ratchet for valve stem on York and Tecumseh service valves, and old style compressor valves. Other end has 3/16 and 5/16 square openings, plus 9/16 hex opening for dust cap on Schrader type valves, and plug for oil check on York compressor.. IMP-125-C 838

72 RATCHET WRENCHES FOR REFRIGERATION/AIR CONDITIONING SERVICE DESCRIPTION 45 FLARING TOOLS Compressor access valve wrench. Chrome plated. Has 1/4, 3/8, 3/16 and 5/16 square drive ratchets and is specially designed for use on compressors with access valves in hard to reach places. Reversible ratchets.. IMP-127-C For soft tubing only copper, aluminum, brass. For 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, and 5/8 tubing. DESCRIPTION IMP-296-FC Flares 7 sizes of tubing. Economical, fast operating tool. Quickslip-on yoke. Easy operating swivel-type, hardened steel,chrome-finished cone assures smooth flares. Chrome and blackfinish. Wt lbs. IMP-195-FC, IMP-195-FCSP Flares 7 sizes of tubing. Rugged forged steel slip-on yoke andhardened flaring bar. Positive clamping action of bars prevents tubeslippage. Self centering yoke with swivel-type, hardened steelchrome-finished flaring cone forms better flares with les 45 METRIC SIZE FLARING TOOL For soft tubing only copper, aluminum, brass. IMP-395-FAM *SP = Skin Packaged DESCRIPTION Same as 195-FC except for metric size tubing 4 mm, 6 mm, 8 mm, 12 mm, 15 mm, 16 mm O.D. tubing. GRABBER ROL-AIR 45 FLARING TOOL Universal application. Adjustable opening holds all sizes. Flares and burnishes 3/16 to 5/8 (4.7 to 16 mm) O.D. tubing. DESCRIPTION Unique, self-adjusting, tube holding mechanism permits flaring any size tubing within the range of 3/16 to 5/8 (4.7 to 16 mm) O.D.tubing. Innovative, single opening design is more compact and easier to use than conventional multi-opening flaring bars. Faceted hardened steel, chrome finished cone rolls out and burnishes perfect 45 flare above the tube holding mechanism reducing need for deburring. Original wall thickness is maintained at base of flare Slip-on self-centering yoke permits use in tight quarters. Large handle, with better leverage, and precision threads on feed screw make flaring effortless. High quality construction with satin chrome and black finish. Wt lbs. IMP-525-F IMP-525-FSP Flares rolled out above die bar by super-smooth faceted cone. Makes stronger flares. 839

73 IMPERIAL TUBING TOOL KITS CUTTING, FLARING, AND SWAGGING KIT For flaring, cutting, and bending soft copper, aluminum, and brass tubing. DESCRIPTION Kit contains a TC-1000 tube cutter for 1/8 to 1-1/8 O.D. tubing and 275-FS flaring and swaging tool. In tool case Wt. 3.0 lbs Flares: 1/8, 3/16, 1/4", 5/16, 3/8, 7/16, 1/2", 5/8, and 3/4" O.D. tubing. Swages: 3/16, 1/4", 5/16, 3/8, 1/2", 5/8, and 3/4" O.D. tubing.. IMP-275-FSC Capacity Ratings are for Air Conditioning Applications: Evaporator Temperature 45 F, Condenser Temperature 130 F, Liquid Temperature 115 F, Return Gas Temperature 65 F, Ambient Temperature 95 F. **Model P/N s containing Q are redesigned to reduce sound levels. Superseded limited to stock on hand 09/01 Limited to stock on hand 10/02. - Tadiran model HEAVY-DUTY RECIPROCATING BLADES Features Designed specifically for rehabbing and demolition work 44% thicker than standard blades Wider than standard blades Unique tooth cutting angle Advantages Staysrigid No vibrating from side to side Durable in wood or metal demolition work Benefits Easy cutting Fast cutting More cuts from each blade Lower sawing costs 840

74 HEAVY-DUTY RECIPROCATING BLADES 5Per Pack Vinyl Pouch 656R 156R 956R 2 Per Card Vinyl Pouch Blister Packed 1 Per Card/5 Cards Per Pack S656R S156R S956R 25 per Box Bulk Packed B656R B156R B956R Length x Width xthickness Inches/ Millimeters 6x3/4x x20x1.3 12x3/4x x20x1.3 9x3/4x x20x1.3 Teeth Per Inch/ 25 mm Shape Recommended Use P1329 P1330 P1331 Rough work in wood, fast cutting, used in remodeling and demolition work. Rough work in wood, fast cutting, used in remodeling and demolition work. Rough work in wood, fast cutting, used in remodeling and demolition work. 676RC S676RC 6x7/16x x11x1.3 6 P1332 Wood contours. 606R S606R B606R 6x3/4x x20x.9 6 P1333 Wood, all composition materials. 634R 610R 810R 110R 314RC 414R 614R 418R 618R 818R S634R S610R S810R S110R S314RC S414R S614R S418R S618R S818R B610R B810R B110R B414R B614R B418R B618R B818R 6x3/4x x20x.9 6x3/4x x20x.9 8x3/4x x20x1.3 12x3/4x x20x1.3 3x1/4x x6x.8 4x3/4x x20x.9 6x3/4x x20x.9 4x3/4x x20x.9 6x3/4x x20x.9 8x3/4x x20x / P1334 P1335 P1336 P1337 P1338 P1339 P1340 P P1343 Nail free woods, fast cutting. Wood, compositions, plastic, cast aluminum, and non-ferrous metals. Wood, compositions, plastic, cast aluminum, light non-ferrous metals, and stainless steel. All woods, plastic, cast aluminum, light non-ferrous metals, and stainless steel. Contour cutting in wood < 3/4" (20 mm) thick and in metal 3/32-5/16 (2.5-8 mm). Heavy gage metal 1/4-1/2 (6-13 mm), hard rubber, fiber, and angle iron. Heavy gage metal 1/4-1/2 (6-13 mm), hard rubber, fiber, and angle iron. Heavy gage metal 1/8-1/4? (3.2-6 mm), conduit and tubing, opening wooden crates, removing wood siding or shingles. Heavy gage metal 1/8-1/4 (3.2-6 mm), conduit and tubing, opening wood crates, removing wood siding or shingles. Heavy gage metal 1/8-1/4? (3.2-6 mm), conduit and tubing, opening wood crates, removing wood siding or shingles. 318RC S318RC 3x1/4x x6x8 18 P1344 Contours -metals under 1/8 (3.2 mm). 424R S424R B424R 4x3/4x x20x.9 24 P1345 Metal and galvanized pipe 18 gage and under. 624R S624R B624R 6x3/4x x20x.9 24 P1346 Metal and galvanized pipe 18 gage and under. 636RP S636RP B636RP 6x3/4x x20x1.3 6 P1347 For plaster, plaster board, and lath. Bi-directional cutting. 841

75 HEAVY-DUTY RECIPROCATING BLADES 5Per Pack Vinyl Pouch 2Per Card Vinyl Pouch 600RG 100RG 800RG Blister Packed 1 Per Card/5 Cards Per Pack 25 per Box Bulk Packed Length x Width x Thickness Inches/ Millimeters 6x3/4x x20x.8 10x3/4x.050 8x3/4x x20x1.0 Teeth Per Inch/ 25 mm Medium Carbide Grit Medium Carbide Grit Medium Carbide Grit Shape P1348 P1349 P1350 Recommended Use Pipe, structural steel, stainless steel, non-ferrous metal: 5/32 (4 mm) and thicker. Nail-embedded. Cast iron, fiberglass, ceramic tile, clay pipe, stone, brick, plaster, and marble. Cast iron, fiberglass, ceramic tile, clay pipe, stone, brick, plaster, and marble. 966R 960R 650R 6510R 6514R 6518R 9x7/8x x22x1.6 9x7/8x x22x1.6 6x3/4x x20x1.3 6x3/4x x20x1.3 6x3/4x x20x1.3 6x3/4x x20x / P1351 P1352 P1353 P1354 P1355 P1356 Demolition work in nail-embedded wood. Demolition work in wood and metal. Fire and rescue. Heavy duty. Extended life when cutting pipe, structural steel, stainless steel: 3/16-3/4 ( mm). Fire and rescue. Heavy duty. Extended life when cutting pipe, structural steel, stainless steel: 1/8-1 ( mm). Fire and rescue. Heavy duty. Extended life when cutting pipe, structural steel, stainless steel: 3/32-38 ( mm). Fire and rescue. Heavy duty. Extended life when cutting pipe, structural steel, stainless steel: 1/16-1/4 (1.5-6 mm). Fire and rescue. 508E 808E 608ER 708ER 110ER 5-1/2x1x x25x1.6 8x1x x25x /2x x25x /8x1x x25x /4x1x x25x /14 P1357 P1358 P1359 P1360 P1361 Pipe, structural steel, non-ferrous metal: 5/32 (4mm) and thicker. Nail embedded wood. Pipe, structural steel, non-ferrous metal: 5/32 (4 mm) and thicker. Nail embedded wood. Pipe, structural steel, non-ferrous metal: 5/32 (4 mm) and thicker. Nail embedded wood. Pipe, structural steel, non-ferrous metal: 5/32 (4 mm) and thicker. Nail embedded wood. Flexible blade. Nail embedded wood, pallets. Metal 1/8-1/2 ( mm) thick. 842

76 MISCELLANEOUS AMERICAN SAW/LENOX TOOLS VARI-BIT KITS VARI-BITS 889 MVB973 VBKME3 STANDARD PACK QUANTITY DESCRIPTION VB1 1 1/8-1/2 VB2 1 1/2-1 VB3 1 1/4-3/4 VB4 1 3/16-1/2 VB6 1 3/8, 1/2 VB7 1 7/8 VB8 1 3/16-7/8 VB9 1 7/8, 1-1/8, 1-7/32 VB11 1 7/8, 1-1/8 VB12 1 7/8, 1-1/8, 1-7/32, 1-1/4, 1-3/8 Bi-metal construction M-2 high speed steel cutting edge Virtually unbreakable High heat resistance Safer than solid high speed steel blades Outperforms carbon steel up to 10 to 1 STANDARD PACK QUANTITY LENGTH x WIDTH (in) TEETH per INCH/25mm V018HE x 1/2 18 V024HE x 1/2 24 V032HE x 1/2 32 V224HE x 1/2 14 V218HE x 1/2 18 V224HE x 1/2 24 V232HE x 1/2 32 HACKSAW FRAME STANDARD PACK QUANTITY DESCRIPTION per sleeve/5 per box High tension hand hacksaw frame per sleeve/5 per box High tension hand hacksaw frame 843

77 LENOX WOOD BORING BITS 1 PER CLAM Resharpenable 1/2 (13mm) shank on all sizes Fits 1/2 (13mm) drill chuck and larger Won t separate when backing out Easy to resharpen on the job - only two cutters Easy to use in tight spots ENTRANCE for DIAMETER (in) PIPE and RIGID CONDUIT (in) TUBING (in) WB /8 1/2 1 WB /4 3/4 1-1/8 WB / /4 WB / /2 WBPS Extra Pilot Screw (Fits all sizes) 5/Pouch WBSS Extra Set Screw (Fits all sizes) 5/Poly Bag * All have 1/2 (13mm) hex shank with 2 set screws to lock bit in place 844

78 LENOX HOLE SAWS Features Bi-metal constructions M-2 high speed steel cutting edge Tooth hardness Rc Vari-Tooth design Positive rake tooth 3/16 (5 mm) thick heavy-duty backing plate 1-1/2 (38 mm) cutting depth Benefits Teeth stay sharper longer Faster cutting Smoother cuts Quieter cutting Better chip clearance Eliminates need for torque driving plate Cuts through 2x4*. * Some arbors limit cutting depth to 1-3/8 (35 mm). Advantages Shock resistant teeth Resists tooth strippage Greatly reduces vibration Aggressive cutting action More durable than stamped backing cups Deep cutting PRODUCT NUMBER 1 PER DIAMETER PIPE TAP PIPE ENTRANCE BOX CLAM (in.) (MM) (in.) (MM) (in.) (MM) USE ARBOR NUMBER (in.) (MM) MILD STEEL TOOL & STAINLESS CAST IRON BRASS ALUMINUM 9L -- 9/ L, 4L, 5L 9/ L K10L 5/ L, 4L, 5L 5/ L -- 11/ L, 4L, 5L 11/ L K12L 3/4 19 1/2 13 3/8 10 1L, 4L, 5L 3/ MM AMSK20MM L, 4L, 5L L -- 13/ L, 4L, 5L 13/ L K14L 7/8 22 3/4 19 1/2 13 1L, 4L, 5L 7/ L -- 15/ L, 4L, 5L 15/ L K16L L, 4L, 5L L K17L 1-1/ L, 4L, 5L 1-1/ L K18L 1-1/ /4 19 1L, 4L, 5L 1-1/ L / L, 4L, 5L 1-3/ L K20L 1-1/ L or 6L 1-1/ L / L or 6L 1-5/ L K22L 1-3/ L or 6L 1-3/ L / L or 6L 1-7/ L K24L 1-1/ / L or 6L 1-1/ L / L or 6L 1-9/ L K26L 1-5/ L or 6L 1-5/ L / L or 6L 1-11/ L K28L 1-3/ / /4 32 2L or 6L 1-3/ L / L or 6L 1-13/ L K30L 1-7/ L or 6L 1-7/ L K32L /2 38 2L or 6L L / L or 6L 2-1/ L K34L 2-1/ L or 6L 2-1/ L K36L 2-1/ L or 6L 2-1/ L / L or 6L 2-3/ L K40L 2-1/ L or 6L 2-1/ L / L or 6L 2-9/ L K42L 2-5/ / L or 6L 2-5/ L K43L L or 6L L K44L 2-3/ L or 6L 2-3/ L / L or 6L 2-7/ L K48L /2 64 2L or 6L L K50L 3-1/ L or 6L 3-1/ L K52L 3-1/ L or 6L 3-1/ L / L or 6L 3-3/ L K56L 3-1/ L or 6L 3-1/ L K58L 3-5/ L or 6L 3-5/ L / / L or 6L 3-3/ L K64L L or 6L L K66L 4-1/ /2 89 2L or 6L 4-1/ L / L or 6L 4-1/ L / L or 6L 4-1/ L K76L 4-3/ / L or 6L 4-3/ L L or 6L L / L or 6L 5-1/ L L or 6L All Boxed Hole Saws 9/16 / 14mm to 1-3/4 / 44mm available in master pack of 10. All Boxed Hole Saws 1-13/16 / 46mm to 3-1/2 / 89mm available in master pack of 5. Suggested RPM s only. Size 845

79 HOLE SAW KITS MAINTENANCE Seven preferred sizes. One each hole saws 7/8, 1, 1-1/4, 1-3/8, 1-1/2, 1-3/4, 2-1/8 (22, 25, 32, 35, 38, 44, 54 mm). One each arbors 5L, 6L. One arbor adaptor. One spare pilot drill. Plastic case. 700K REFRIGERATION Six sizes preferred by refrigeration professionals. One each hole saws 5/8, 7/8, 1-1/8, 1-3/8, 1-5/8, 2-1/8 (16, 22, 29, 35, 41, 54 mm). One each arbors 5L, 6L. One spare pilot drill. Plastic case. LENOX HOLE SAWS 1 PER CLAM 600R DESCRIPTION CHUCK SIZE in (mm) FITS ARBOR NUMBER 4321 Pilot Drill* 1/4 (6) 1L, 1SL, 2L, 2SL, 4L 56PD Pilot Drill* 1/4 (6) 5L, 6L AA1 Arbor Adaptor** 1L, 1SL, 4L, 5L 18X 18" (450 mm) Extension 1/2 and larger (13) 1L, 2L 12X 12" (100 mm) Extension 1/2 and larger (13) 1L, 2L 10X 10" (250 mm) Extension 3/8 and larger (10) 5L, 6L 55X 5-1/2" (140 mm) Extension 1/2 and larger (13) 1L, 2L 1 PER BOX ARBORS *Order Pilot Drills in multiples of ten. **Arbor Adaptors 1 per card. Order in multiples of five. CHUCK SIZE in (mm) FITS HOLE SAWS SHANK TYPE L 1/2 and larger (13) 9L-19L Hex SL* -- 9L-19L SDS L 1/2 and larger (13) 20L-96L Hex SL* -- 20L-96L SDS L 1/2 and larger (13) 20L-96L Solid/Hex L 1/4 (6) and larger 9L-19L Round L 3/8 (10) and larger 9L-19L Hex L 3/8 (10) and larger 20L-96L Hex 846

80 TRI-FOLD SAW Features Heavy-duty aluminum handle Complete with 6 (150 mm) Lenox Reciprocating Blade Blade folds away safely Locks in 3 positions Comfortable hand grip Hanging hole in handle Accepts reciprocating blades using 1/2" (13 mm) tang 1 PER CLAM/5 PER BOX Advantages Resists breakage Easytouse Lightweight Easy blade change Benefits Cuts in hard-toget-at places Easy to carry on the job/fits in your pocket Safe to use Savestime PVC/ABS PLASTIC PIPE HAND SAW Features One piece carbon steel construction Tooth hardness Rc /2 (64 mm) blade width Precision milled teeth Spring tempered blade back HANDLE Features Heavy-duty aluminum Single screw blade attachment Advantages Good wear resistance Cuts larger diameter than a hacksaw Teeth stay sharper longer Cuts on push and pull stroke Resists flexing Advantages Sturdy, durable Virtually unbreakable Easy to assemble DESCRIPTION Tri-Fold Saw Wood, drywall, and non-metallic Tri-Fold Saw Metal Cutting Benefits Cuts plastic, wood,and drywall Cuts nail-embedded wood Lasts longer Savestime Cuts faster Cuts straighter Benefits Comfortable Long lasting Easy blade change HSF-180 HSF-120 HSB-18 HSB-12 FCBA* CLOSE QUARTER SAW 1 PER SLEEVE/5 PER BOX *1 PER CARD / 5 PER BOX Features Rigid solid bar construction Hardened carbon blade Increased blade tensioning Advantages Cuts where other frames can t Easy blade change SAW - 1 PER CARD / 5 PER BOX. BLADES - 10 PER CARD DESCRIPTION 18 (450 mm) blade and handle 12 (300 mm) blade and handle 18 (450 mm) replacement blade 12 (300 mm) replacement blade Flush cutting blade adaptor Benefits Increases productivity Savestime Straight cuts DESCRIPTION 908 Close Quarter Saw 906 Replacement Blades 6 x 1/4 x.014 x 32T (150 mm x 6.4 mm x.35 mm x 32T) 847

81 Moty-Ko 14DD 14.4V Cordless Heavy Duty Drill / Driver 380 in/lbs of maximum torque for a wide range of application Rigid aluminum gearbox for both durability and heavy-duty application Auto spindle lock function for ease of bit changing and manual screwing Built-in bubble level for horizontal drilling and precise screwing Built-in battery capacity indicator for easy monitoring Anti-slip soft grip provides both comfort and protection No load speed of / 0-1,150 RPM Jacobs 1/2 keyless chunk, all metal single sleeve Two (2) Sanyo 2.0Ah slide-in battery packs All metal, auto spindle lock gearbox Packed by blow carrying case with extra battery pack, 1 hour fast-charger and 2-piece screw bit Moty-Ko 18HD 18V Cordless Heavy Duty Drill / Driver 400 in/lbs of maximum torque for a wide range of application Rigid aluminum gearbox for both durability and heavy-duty application Auto spindle lock function for ease of bit changing manual screwing Built-in bubble level for horizontal drilling and precise screwing Built-in battery capacity indicator for easy monitoring Anti-slip soft grip provides both comfort and protection No load speed of 0-400/ 0-1,200 RPM Jacobs 1/2 keyless chunk, all metal single sleeve Two (2) Sanyo 2.0Ah side-in battery packs, 1 hour fast-charger and 2-piece screw bit All metal, auto spindle lock gearbox Packed by blow carrying case with extra battery pack, 1 hour fast-charger and 2-piece screw bit 848

82 Moty-Ko 12ID 12V Cordless Heavy Duty Impact Driver 1,050 in/lbs of maximum torque for a wide range of fastening applications Compact ergonomic design for easy operation and reduction of hand fatigue Anti-slip soft grip provides both comfort and protection Heavy-duty 1/4" hex drive with quick release External replaceable carbon brusher for maximum motor life Rigid cast aluminum hammer case for durability and effective heat dissipation 1-hour fast charger No load speed of 2,300 RPM Impact rate of 3,000 BPM Overall length of 6-1/2" Packed by blow carrying case with extra battery pack, hour fast-charger and 2-piece screw bit Moty-Ko 18V Cordless Heavy Duty Reciprocating Saws MOTY-KO: 18RS - Saw and Case 18RS1 - Saw, Case, 1 Battery and Charger 18RS2 - Saw, Case, 2 Battery and Chargers 1 Stroke length for smooth cutting Quick blade change Accepts 4 blade types No load strokes per minute Anti-slip soft grip provides both comfort and protection Die cast gear housing Built-in battery capacity indicator for easy monitoring 18V battery is interchangeable with other Moty-Ko 18V tools Tool weight 7.5 pounds 849

83 DIGITAL MULTI-METERS Compact size fits in pocket 2 volt range, allows use of CO attachment and temperature attachment. 2k ohm range reads most contactor and relay coils. Standard accessories; test leads, batteries, protective boot, instruction manual, and a 3 year limited warranty. Full function manual range DMM. Test continuity in circuits and wires. Measure current draw of electrical circuits. Measure start and run capacitors of motors and compressors. Test diodes for shorts and opens. Measure resistance of components. Standard accessories; test leads, batteries, protective boot, instruction manual, and a 3 year limited warranty. 120 Full function manual range DMM. Large LCD Measures amps to 10 amps both AC & DC. Measures DC micro amps for flame rectification circuits. Continuity buzzer and diode check. Standard accessories; test leads, batteries, protective boot, instruction manual, and a 3 year limited warranty. 135 Full function auto ranging DMM. Test continuity in circuits and wires. Measure current draw of electrical circuits. Test diodes for shorts and opens. Measure resistance of components. Standard accessories; test leads, batteries, protective boot, instruction manual, and a 3 year limited warranty

84 DIGITAL MULTI-METERS Part No.: 163 Part No.: 183 Full function auto ranging DMM. Auto ranging true RMS DMM. Test continuity in circuits and wires. Measures Capacitance. Measure current draw of electrical circuits. Test continuity in circuits and wires. Test diodes for shorts and opens. Measure current draw of electrical circuits. Measure resistance of components. Test diodes for shorts and opens. Standard accessories; test leads, batteries, Measure resistance of components. protective boot, instruction manual, and a 3 Standard accessories; test leads, batteries, protective boot year limited warranty. instruction manual, and a 3 year limited warranty. FEATURES Display Count AC Volts DC Volts Basis DC Accuracy 0.50% 0.50% 0.50% 0.30% 0.50% 0.30% AC Amps NA DC Amps NA True RMS NA NA NA NA NA NA Resistance 2K ohms 20M ohms 40M ohms 40M ohms 32.6M ohms 40M ohms Capacitance NA NA 20,000uF NA NA 10,000uF Frequency NA NA NA NA NA 200KHz Analog Bar Graph NA NA NA NA YES YES Auto Range NA NA NA YES YES YES Data Hold YES YES YES YES YES YES Min./Max NA NA NA YES NA YES Sleep Mode NA NA NA NA NA YES Auto Power Off NA NA NA YES YES NA RS232 (cable & Software NA NA NA NA NA OPTIONAL CE or UL Listed CE culus CE culus CE CE culus CE culus CE culus

85 DIGITAL CLAMP-ON METERS 255 Autoranging Compact Size Test continuity in circuits and wires Measure current draw of electrical circuits. Measure resistance of components. Measure inrush current of motors, relays and solenoids. 293 Autoranging true RMS clamp-on Peak hold, trim mode and data hold functions. Measure AC/DC volts, frequency, AC amps and ohms to 40M ohms. Analog bar graph and continuity buzzer. Standard accessories include soft pouch test leads and a limited 3 year warranty Manual range meter measures up to 700 AC amps. Peak hold and data hold functions. Continuity buzzer. Measures AC/DC volts and ohms to 4K ohms. Complete with soft pouch, test leads, instruction manual and a 3 year limited warranty True RMS and Harmonics features. Measures line and controls circuit voltage. Measures current draw of electrical circuits. Measures inrush current of motors, relays and solenoids. Measures resistance of components. Standard accessories include soft pouch, test leads and a 3 year limited warranty. 291 FEATURES Display Count AC Volts DC Volts Basis DC Accuracy 0.30% 0.75% AC Amps DC Amps NA 20uA HDR Mode NA NA True Amps NA NA Resistance 40M ohms 40M Frequency NA 10K Hz Temperature YES Capacitance 20,000 uf Analog Bar Graph NA NA Auto Range YES YES Data Hold YES YES Min./Max YES YES Trim NA YES Sleep Mode NA NA Auto Power Off YES YES CE or UL Listed CE culus CE culus % 0.75% 0.75% NA NA 700 NA NA YES NA NA YES 4K ohms 40K ohms 40K ohms NA 10K Hz 10K Hz NA YES YES NA YES YES YES YES YES PEAK ONLY PEAK ONLY YES NA YES YES NA YES YES NA NA NA CE CE culus CE culus

86 DIGITAL CLAMP-ON METERS Hand held oscilloscope with True RMS DMM capabilities View industrial signals such as motor control, UPS, switching power supplies and PLC controls with 1 MHz bandwidth. Capture noise spikes, glitches and evasive intermittents with 25 Mega samples per second sampling rate. Continuous autoset. Real time display with backlight. Waveform storage Clitch capture Trend mode Frequency counter Basic DC accuracy to 0.3% RS-232C Port Designed to meet IED V Cat III rating. Specifications OSCILLOSCOPE Band Width Sample Rate Channels Glitch Capture Trend Mode Auto Set Waveform Memory Set-Up Memory Viewing Area Contrast DMM True RMS Basic DC Accuracy DCV/ACV DCA/ACA Ohms Capacitance Frequency 1MHZ 20 Mega samples per second (single shot) Single Yes Yes Continuous 8 Locations 8 Locations 160 x 240 pixels Adjustable Yes 0.3% Up to 1,000 volts Up to 10 amps Up to 40 Mega ohms Up to 400 microfarads Up to 2 MHZ DESCRIPTION scope plus, 4,000 count true RMS DMM with wave form capabilities, insulated test leads with alligator clips, power supply and NiCad battery. POCKET DIGITAL THERMOMETERS Flip the LCD to give best angle for viewing Easy to read, large LCD Data Hold for hard to reach areas Auto Power Off saves battery life Fahrenheit or Celsius

87 POCKET DIGITAL THERMOMETERS Easy to read, large LCD - 33% larger than the competition Use in damp or wet environments - WATER RESISTANT Quick response and easy insertion into Petes plugs with 3.1 mm dia. stem Data Hold for hard to reach areas. Auto Power Off saves battery life Fahrenheit or Celsius NON CONTACT THERMOMETERS 312 Easy-to-read, large LCD Maintain reading display in hard to read areas with Display Hold F or C Selectable 0.95 Emissivity Provides best accuracy for most surfaces 8:1 Distance to Spot Ratio 0.1 Resolution provides increased accuracy of reading 3 Year limited Warranty SPECIFICATIONS 370 w/o Function /381 laser -58 to 0 to to 500 F to 550 F 14 to 950 F 0 to 950 F 0 to 1832 F Temp Ranges 950 F -50 F -18 to to 260 C -50 to 288 C -10 to 510 C 18 to 510 C 18 to 100 C to 510 C 260 C Laser Sighting No Yes Yes Yes Yes Yes Yes No/Yes 23 C and.95 Emissivity -2% of Reading or +/-3.5, whichever is greater above 30 F 30 to 950 F -1 F to 510 C: +/-2% of reading or +/- 3.5 F (2 C) whichever is greater 30 to 950 F-18 to 1000 C +/-2% or reading or +/- 3.5 F (2 C) whichever is greater ±2% or ±2 C or ±3 F whichever is greater Response Time 500 milliseconds Spectral Resp um Operating Temp 32 to 120 F and 0 to 150 C Battery Type 9 Volt Alkaline Emissivity to 0.99 adjustable 0.95 Display F and 0.1 C or 1 F and 1 C Resolution Ambient Operating Range 32 to 120 F and 0 to 50 C K-Type Range -40 to 2192 F and -40 to 1200 C K-Type Accuracy +/-0.5% pf reading +3 F 854

88 DUAL CHANNEL THERMOMETER Applications Measure Superheat from refrigeration systems with built-in temp. differential. Measure steam trap temps Measure thermostat accuracy Measure heating and cooling register temps FEATURES Water Resistant YES YES YES Min/Max Record NA YES YES Selectable Res. NA YES AUTOMATIC C/F Selectable NA YES YES Scan Mode NA NA YES (dual inputs) Range K-Type -40 to 1200 F -328 to 2462 F -328 to 2462 F -200 to 1000 C -200 to 3250 C Range J-Type NA -328 to 1832 F -238 to 1832 F -200 to 1000 C -200 to 1000 C Basic Accuracy +/-1%+4 digits +/-0.3% +/-0.3% Battery AAA 9V 9V FEATURES. 362 Water Resistant YES Min/Max Record YES Selectable Res. AUTOMATIC C/F Selectable YES Scan Mode YES (dual input) Range K-Type -418 to 2500 F -200 to 1375 C Range J-Type -328 to 1832 F -200 to 1000 C Range T-Type -418 to 752 C -250 to 400 C Basic Accuracy +/-0.1% Battery 9 V GAS DETECTION PRODUCTS CARBON MONOXIDE DETECTORS Applications Conduct tests of CO levels in room air to meet ASHRAE and OSHA standards. Confirm proper operation of alarming CO detectors in households. Check for proper installation of ventless gas fireplaces, furnaces and other combustion devices. Specifications DMM Requirements Range Sensor Type Response Time Operating Temperature Relative Humidity Duty Cycle Power Supply Battery Life 2 or Volt DC Range 10 Megohum input impedance ppm with 3-1/2 digit DMM display Electrochemical 90% of reading in 60 Seconds F 5-95% non-condensing Continuous 1 each 9 Volt Battery 2000 hrs. typical A

89 GAS DETECTION PRODUCTS CARBON MONOXIDE DETECTORS Applications Carbon monoxide investigation in residential and commercial buildings. Boiler and Furnace efficiency testing. Safety testing. Verifying boiler and furnace service and maintenance. 705 Applications Measures CO, O2 and temperature Calculates CO2, efficiency and net temperature Pump Driven for fast response Includes flue probe with built in Thermocouple and hard carrying case. Infrared printer interface to produce hard-copy documentation Specifications Range ppm Resolution 1 ppm Response Time 3 seconds, 90% of reading in 30 Second Accuracy +/-3 ppm, +/-3% of reading F, 5-95% Relative Humidity, noncondensing Operating Temperature Zero Adjustment Push Button Power Supply 3 C Alkaline Battery Battery Life 20+ hrs. continuous operation 710 COMBUSTIBLE GAS LEAK DETECTORS Used to detect gas leaks in the following areas: Furnaces Water Heaters Popabe and combustible gas links and storage tanks Gas appliances Features 720B HXG2 Sensitivity 10 ppm 10 ppm Methane Sensor Type Low power semiconductor Solid State Warm-up 30 Seconds Approximate 1 minute Response Time Instantaneous <2 seconds Duty Cycle Continuous Intermittent Probe Length 16 inches 16 inches Power Supply 3 C Cell Batteries 3 C Alkaline

90 DIGITAL MANOMETERS Applications Adjusting appliance regulators Setting delivery pressures Leakage shut-in tests Regulator adjustments for pressure and lock-up tests Test pressure switch operation on a 2-stage gas furnace in both positive and negative pressures Features Auto Range mbar to mbar 5 PSI 30 PSI 100 PSI Accuracy ±(0.5% of reading + 5 digits) ±0.2% of full scale +3 digits Over Pressure 500 mbar 1000 mbar 4000 mbar 10 Bar Power Supply 9V Relative Humidity 0% to 80% (0 to +40 C) Operating Temp. 32 F to 104 F (0 C to +40 C Storage Temp. 14 F to 122 F (-10 C to +50 C) Auto Power Off After 40 minutes After 30 minutes Input Type Single Single Differential Differential Differential Differential Differential Trim Mode Yes Yes Yes Yes Yes Yes Yes Zero Adjust Yes Yes Yes Yes Yes Yes Yes Record Min/Max No Yes No Yes Yes Yes Yes Units Data Hold No Yes No Yes Yes Yes Yes Units available are Pa, PSI, in HG, mmhg, mmh2o, mbar 857

91 CO AND FLUE GAS ANALYSIS Specifications Specification CO Measurement 0-10,000 ppm O2 Measurement NA 0-25% NO Measurement NA 0-5,000 ppm NOx (Calculated) NA 0-5,250 ppm CO2 Measurement NA 0-25% CO/CO2 Ratio NA 0 to Combustible Leak Indication NO YES NO Pressure NO YES Pressure Differential NO YES Stack Temp (CH1) NO YES Ambient Temp (CH2) NO YES Temperature Differential NO YES Excess-Air NO YES Air-Free (CO) NO YES Efficiency NO YES Store Memory Data Logging Memory NO YES IRDA (Optional) NO YES Battery 3 AA Batteries Rechargeable* *Units come with rechargeable batteries and chargers. DESCRIPTION 707 Single Gas CO Analyzer with protective boot, soft shoulder strap carrying case, pump-protecting filter assembly, in-line filter assembly, flue probe. 3 AA batteries. 708 Combustion Efficiency Analyzer, CO Analyzer, and Differential Thermometer with protective boot,stack probe, water/filter trap on stack probe, carrying case, mini in-line pump filter, manual. 712 Flue Gas Analyzer for Combustion Efficiency. Combustible Gas, CO Analyzer, Differential Thermometer, and Differential Manometer with rotective boot, flue probe w/k-type thermocouple probe. 714 Flue Gas Analyzer for Combustion Efficiency, CO Analyzer, NO & NOx Analyzer, and Differential Thermometer with protective boot, stack probe, PVC tubing, water filter trap on stack probe. 715 Flue Gas Analyzer for Combustion Efficiency, High CO Analyzer, NO & NOx Analyzer, and Differential Thermometer with protective boot, stack probe, PVC tubing, water/filter trap on stack probe. A740 INFRARED PRINTER Easy to use Battery operated Self test facility Adjustable contrast Manual paper feed Maximum transmitting distance 16 in. (45 cm) Compatible with most other combustion analyzers. A740 DESCRIPTION IR Portable Printer 858