KOMET Kub-It HD COMPATIBLE Coolant Thru Indexable Drills

Transcription

1 COOLANT THRU INDEXALE DRILLS TRIDEX INDEXALE DRILLS KOMET Kub-It HD COMPATILE Coolant Thru Indexable Drills ALL SM TRIDEX COOLANT THROUGH INDEXALE DRILLS ARE : 100% Compatible with inserts for KOMET KU-IT drills & Kennametal DFT- 84 Trigon drill inserts. lack oxide surface to prevent against rust and corrosion. Length to diameter ratios are kept optimal tool overhang is minimized and tool rigidity, accuracy and deflection are minimized even in deeper holes. Spiral flutes to improve chip evacuation while keeping tool strength intact. Insert pockets are precisely positioned to keep cutting forces low and evenly distributed thus -lower axial pressures are realized. The net result of this is minimal tool deflection which in turn produces straighter holes regardless of whether the surface being drilled is concave, convex or is a low angle surface. Trigon Inserts - our unique 84 nose angle Trigon inserts provide the strength of a square insert with the versatility of a triangular insert. The 8 positive relief angle provides for easier cutting by using positive cutting action. The 156 angle between cutting edges - provides twofold benefits - eliminates the need for spotfacing or pre-centering before drilling and can be indexed 3 times. 100% Guaranteed against defects and backed by our Industry Famous guarantee. Manufactured from H13 steel for superior tool toughness and strength. 3 Methods Of Coolant Entry: Rear Entry, coolant supply through the back of the shank. Side entry, coolant supply through the side of the tool. Through the holder, for Mori-Seiki and other machines, coolant supply through the slot on the shank. DRILLING TIPS Indexable drills are designed strictly for roughing and as not meant to be used for finishing. Tolerances of and finishes of 250 rms are normal. FIXTURE RIGIDITY is extremely important when using indexable drills. Workpieces should be of adequate strength flimsy workpieces will cause drills to be rendered almost ineffective due to high horsepower requirements. RUNOUT must be checked with the drill in the toolholder. Position the drill such that the inboard station is positioned below center radially. This allows the inboard insert to cut past the center. Using a dial indicator check the drill for location if the location varies more than.002 at the holder and/or.006 at the cutting edge of the drill then the drill and/holder must be repositioned or the TIR of the holder must be checked/adjusted. ADEQUATE COOLANT is essential when using indexable drills. Maximum heat is produced in a small area at the bottom of the hole being drilled. In general 10-20gpm at 45psi of coolant is required during drilling. When drilling deeper than 1X drill diameter, coolant through the drill is essential - flood coolant cannot perform satisfactorily at depths beyond 1X drill diameter. PROPER CHIP CONTROL is absolutely necessary to remove chips, this improves hole tolerance and finish and also improves tool life. Adjust speed and feed to produce figure 9 chips for optimal chip removal longer chips will lead to chip buildup in the drill flutes and chip recutting and eventual drill failure. Increase speed (within limits) if chips are too short. If chips are still unsatisfactory, reduce feed.decrease speed or increase feed if chips are too long. OFFSETTING DRILLS with 2.5:1 length to diameter ratios, in a positive direction, has proven to beneficial when using indexable drills on machines with inadequate coolant supply. Offsetting will reduce chatter and improve surface finish. Offsetting is also useful when drilling a slightly oversized hole. This allows for drilling a larger range of hole diameters with a minimum of drill diameter. HORSEPOWER A machine with at least seven horsepower is required to run an indexable drill. SM Indexable drills are not designed to be used with stacked materials or laminates severe tool damage and loss will occur if used with such materials. On some CNC machines, the rapid rate of tool positioning does not allow enough time for coolant flow to begin prior to drill contact with the workpiece. If the drill begins cutting without coolant, even for a second or two, insert life can be greatly reduced. Adding a short dwell in the program, to assure coolant flow EFORE workpiece contact, will considerably increase insert life and drill performance. The slug produced by drilling through a workpiece can sometimes become jammed between the drill and workholding device. To minimize the likelihood of this happening, provide ample clearance in this area. To help insure the proper placement of the insert you should hold the insert in place with your thumb and index finder while tightening the torx screw with your other hand. CARIDE INSERTS Index Finger Screw Push Push Torx Screwdriver Newcomer Insert DEURRING Indexable Drill Thumb *KOMET, Kub-It and Kennametal are trademarks of their respective companies Master Catalog 269

2 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD COOLANT THRU INDEXALE DRILLS TRIDEX INDEXALE DRILLS KOMET KU-It COMPATILE Coolant Thru Indexable Drills Premium Drills: Manufactured from H-13 steel (hardened to Rc 46/50) for greater tool strength, reduced wear and longer tool life Standard Drills: Manufactured from tool steela quality drill at a great price! 5 and 6 drill depths now available! Compatible with inserts for Komet Kub-It and Kennametal DFT-_ 84 trigon drill inserts Spiral flutes to improve chip evacuation Insert pockets are precisely positioned to keep cutting forces low and evenly distributed 100% Guaranteed against defects lack oxide finish for long life Made in the! Drill Type: S=Standard Drill P=Premium Drill D S Drill Depth 1.00 Drill Depth 2.00 Drill Depth 3.00 Drill Depth 4.00 and Over Drill. Size Drill Type Drill Type Drill meter Insert I.C DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ /16 7/ Master Catalog Drill Type DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ Drill meter Insert I.C DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ /16 7/ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ Flute Len DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ Drill meter Insert I.C DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ /32 1-1/ DK S $ DK P $ DK P $ DK P $ DK S $ DK S $ DK P $ DK P $ DK P $ DK P $ DK S $ DK P $ DK S $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ DK P $ Drill meter Insert I.C DK P $ DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ DK P $ /4 1-5/16 1-3/8 1-7/16 1-1/2 1-9/16 1-5/8 1-11/16 1-3/4 : to Drill : to Drill Depths: 1 to DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK S $ DK P $ DK P $ DK P $ DK P $ DK S $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK S $ DK P $ DK P $ DK S $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK S $ DK P $ DK S $ DK S $ DK S $ DK P $ DK P $ DK P $ DK S $ DK S $ DK P $ DK S $ DK S $ DK P $ DK P $ DK P $ DK S $ DK S $ DK S $ DK S $ DK S $ DK P $ DK P $ DK P $ DK S $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ *KOMET, Kub-It and Kennametal are trademarks of their respective companies. Drill Type E Larger meter Drills Continued Page 259

3 COOLANT THRU INDEXALE DRILLS INDEXALE DRILLS (continued) Coolant Thru E Drill Type: S=Standard Drill P=Premium Drill D S Drill Depth 1.00 Drill Depth 2.00 Drill Depth 3.00 Drill Depth 4.00 and Over Drill. Size Drill Type Drill Type Drill Type Flute Len Drill meter Insert I.C. 1-13/ DK P $ DK P $ DK P $ DK S $ / DK P $ DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ DK P $ Drill Type Drill meter Insert I.C. 2-1/ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ Drill meter Insert I.C. 2-3/ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ DK P $ / DK P $ DK P $ DK P $ DK P $ INDEXALE DRILL INSERTS TRIDEX PREMIUM 84 TRIGON COATED INSERTS A Major feature of the TRIGON insert is its 84 nose angle which combines the strength of a square with the versatility of a triangular insert. Drill IC T H X R Grade SZP40 Coated C2 Coated Inserts Grade SP35 Coated C5 Uncoated Inserts Steel, SS, Hi-Temp Steel, SS - TRX-197-SZP40-A $8.08 TRX-250-SZP40-A $8.16 TRX-315-SZP40-A $8.52 TRX-394-SZP40-A $9.78 TRX-472-SZP40-A $11.57 TRX-591-SZP40-A $16.26 TRX-693-SZP40-A $20.46 TRX-197-SP35-A $8.08 TRX-250-SP35-A $8.16 TRX-315-SP35-A $8.52 TRX-394-SP35-A $9.78 TRX-472-SP35-A $11.57 TRX-591-SP35-A $16.26 TRX-693-SP35-A $ Master Catalog NOT NECESSARY NOT NECESSARY NOT NECESSARY NOT NECESSARY NOT NECESSARY NOT NECESSARY NOT NECESSARY Screw SC DK $1.25 SC DK $1.25 SC DK $1.25 SC DK $1.25 SC DK $1.25 SC DK $1.25 SC DK $1.25 Torx Driver TX-206 $5.00 TX-206 $5.00 TX-208 $5.00 TX-210 $5.00 TX-215 $5.00 TX-215 $5.00 TX-220 $5.00 E CARIDE INSERTS DEURRING

4 CHUCK JAWS LATHE WORKHOLDING INDEXALE DRILLS INSERTS KOMET KU TRIGON COATED & UNCOATED INDEXALE DRILL INSERTS KOMET MACHINE VISES Genuine KOMET Inserts Drill IC T H X R Coated Inserts Uncoated Inserts Komet Grade K62 Komet Grade K84 Komet Grade K10 Komet Grade P40 TiCN/AI203-CVD Coated C2- Cast Iron KOM-0236-K62 $11.47 C5- Steels, Cast Steels, Stainless KOM-0236-K84 $11.47 C2- Aluminum Cast Iron KOM-0236-K10 $8.98 C5- Non-Alloy & Die Steels, SS KOM-0236-P40 $8.98 Screw SC DK $1.25 Torx Driver TX-208 $5.00 RETENTION KNOS ER, DA, TG COLLETS KOM-0315-K62 $10.81 KOM-0394-K62 $10.99 KOM-0472-K62 $12.98 KOM-0590-K62 $18.46 KOM-0693-K62 $23.00 KOM-0315-K84 $10.81 KOM-0394-K84 $10.99 KOM-0472-K84 $12.98 KOM-0590-K84 $18.46 KOM-0693-K84 $23.00 KOM-0315-K10 $7.12 KOM-0394-K10 $8.43 KOM-0472-K10 $10.62 KOM-0590-K10 $14.49 KOM-0693-K10 $19.46 KOM-0315-P40 $7.12 KOM-0394-P40 $8.43 KOM-0472-P40 $10.62 KOM-0590-P40 $14.49 KOM-0693-P40 $19.46 SC DK $1.25 SC DK $1.25 SC DK $1.25 SC DK $1.25 SC DK $1.25 TX-208 $5.00 TX-210 $5.00 TX-215 $5.00 TX-215 $5.00 TX-220 $5.00 TOOLHOLDERS INDEXALE DRILLS TURNING & ORING KOMET COATED AND UNCOATED INSERTS GRADES AND SPEED/FEED INFORMATION Komet Grade K84 P 40 K 10 K 62 Application An TiCN/TiN-PVD coated grade which combines toughness with good wear resistance. For machining steel, cast steel and stainless steel. ecause of the PVD coating, K84 is the preferred grade for internal inserts for insert drills (less build-up on cutting edges). K84 is also suitable for external inserts on insert Uncoated carbide with medium wear resistance at optimum toughness factor. Low to medium cutting speeds for roughing and with heavily interrupted cut. Also for unstable working conditions. For non-alloy steel, die steel and stainless steels Chamfered and neutral cutter geometry suitable for all grades of cast iron. Positively Molded (PD) and ground geometry is used for aluminum. E.g.:20 top rake, ground. Sharply and light honed. TiCN and Al2O3-CVD-coating for higher cutting speeds in all types of cast iron materials. Only limited suitability for extreme interrupted cut. Not suitable for Aluminum materials. KOMET Coated And Uncoated Inserts Speed-Feed Information Helpful formula: rpm = (3.82 X SFM) / (tool diameter) KOMET ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Material Hardness (H) Speed (sfm) Feed (ipr) oring Depth 2x / 3x Drill Drill Drill > Master Catalog Drill.750 oring Depth 4x Drill Drill Mild steel Up To Free cutting steel Up To Mild case-hardened and heat-treated steel Heat steel alloyed Cr and CrMo steel Tool and heat-treated steels < Stainless and heat-resistant steels Cr;CrNiu.CrNiMo-alloys Hardened steels Over Cast steel Upto Cast iron High strength cast iron/alloy cast iron Over Upto Aluminium alloys Over Heat resistant super alloy (Cobalt based) Plastics solid KOMET is a registered trademark of KOMET of America

5 COOLANT INDUCED HOLDERS COOLANT INDUCED TOOLHOLDERS For mounting drills on machine tools & machining centers where there is no provision for feeding coolant through the machine spindle. FEATURES: Add performance and life to cutting tools Reduced wear means higher consistency and tighter tolerances All holders come complete with coolant connection 750 SFM/200 PSI on O rings Coolant induced collars and replacement parts available Includes Toolholder and Coolant Collar TRIDEX PREMIUM TRIGON COATED INSERTS SPEED & FEED INFORMATION Made In Germany CAT V-Flange CAT 40 CAT 50 A Hole Size Dim C Proj. D E. 3/ C40-75CIH444-C $ C40-10CIH600-C $ / C40-12CIH569-C $ / C50-75CIH456-C $ C50-10CIH600-C $ / C50-12CIH569-C $ / C50-15CIH575-C $ T T30 3/ CIH456-C $ T 40 T 50 3/ CIH444-C $ / CIH569-C $ / CIH456-C $ / CIH569-C $ / CIH575-C $ Mat. Group TRIDEX PREMIUM INSERTS Workpiece Material rinell Hardness- H Mach Group DOC [in] Drill. SP 35 SZP 40 f [in/.rev.] f [in/rev/] approx. 0.15% C annealed approx. 0.45% C annealed Unalloyed steel approx. 0.45% C tempered approx. 0.75% C annealed approx. 0.75% C tempered annealed P tempered Low-alloyed steep tempered tempered High-alloyed steel and annealed high-alloyed tool steel hardened by tempering Stainless steel ferritic / martensitic, annealed martensitic, tempered M Stainless steel austenitic2, retained Grey cast iron pearlitic/ferritic pearlitic (martensitic) Cast iron with ferritic K spheroidal graphite pearlitic Malleable cast iron ferritic pearlitic Aluminum malleable non-age-hardenable alloys age-hardenable, age-hardened < 12% Si, non-age-hardenable Aluminum cast alloys < 12% Si, age-hardenable,-hardened > 12% Si, non-age-hardenable Free cutting alloys, Pb > 1 % N Copper and copper rass, red brass alloys (ronze/brass) ronze unleaded & electrolytic copper Duroplasts Non-metallic materials fiber-reinforced plastics Hard rubber Fe basis annealed age-hardened Heat-resistant alloys Ni or annealed S Co basis age-hardened cast Titanium alloys Pure titanium Alpha + eta alloys,age-hardened > Master Catalog 273 CARIDE INSERTS DEURRING

6 CHUCK JAWS LATHE WORKHOLDING 4-IN-1 INDEXALE DRILLS SHARK-CUT INDEXALE COOLANT THRU DRILLS Cost Reduction Through Performance! 4-in-1 Indexable Coolant Thru Drill A MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD INCH SHANK 1.5 x D Drill Inch Inch F Inch L2 Inch Drill Depth L1 Inch Master Catalog Manufacturer s Reference # RA08R-1205G04E $ SC08R-0012G04E RA10R-1505G05E $ SC10R-0015G05E RA12R-1862G06E $ SC12R-0018G06E RA14R-2162G07E $ SC14R-0021G07E RA16R-2475G08E $ SC16R-0024G08E RA18R-2710G09E $ SC18R-0027G09E RA20R-3010G10E $ SC20R-0030G10E RA25R-3812G13E $ SC25R-0038G13E RA32R-4815G17E $ SC32R-0048G17E 17 INCH SHANK 2.25 x D Drill Inch Inch F Inch L2 Inch Drill Depth L1 Inch Manufacturer s Reference # RA08R-1837SP04E $ SC08R-0018SP04E RA10R-2305SP05E $ SC10R-0023SP05E RA12R-2762SP06E $ SC12R-0027SP06E RA14R-3262SP07E $ SC14R-0032SP07E RA16R-3675SP08E $ SC16R-0036SP08E RA18R-4110SP09E $ SC18R-0041SP09E RA20R-4510SP10E $ SC20R-0045SP10E RA25R-5712SP13E $ SC25R-0057SP13E RA32R-7215SP17E $ SC32R-0072SP17E 17 METRIC SHANK 1.5 x D Drill mm mm F mm L2 Drill Depth L1 Manufacturer s Reference # , RA08R-1212G04 $ SC08R-0012G , RA10R-1512G05 $ SC10R-0015G , RA12R-1816G06 $ SC12R-0018G , RA14R-2116G07 $ SC14R-0021G , RA16R-2420G08 $ SC16R-0024G , RA18R-2725G09 $ SC18R-0027G , RA20R-3025G10 $ SC20R-0030G , RA25R-3832G13 $ SC25R-0038G , RA32R-4840G17 $ SC32R-0048G17 17 METRIC SHANK 2.25 x D Drill mm mm High performance drilling and turning system-effective and productive! CNC polished inserts (AWI/WI) are available in coated or non-coated finish Extremely efficient boring tool suitable for turning and boring Four machining processes possible with one tool! Maximum precision and process dependability All holders are equipped with an internal coolant feed Drilling depths up to 3X D F mm L2 Drill Depth L1 Manufacturer s Reference # , RA08R-1812SP04 $ SC08R-0018SP , RA10R-2312SP05 $ SC10R-0023SP , RA12R-2716SP06 $ SC12R-0027SP , RA14R-3216SP07 $ SC14R-0032SP , RA16R-3620SP08 $ SC16R-0036SP , RA18R-4125SP09 $ SC18R-0041SP , RA20R-4525SP10 $ SC20R-0045SP , RA25R-5732SP13 $ SC25R-0057SP , RA32R-7240SP17 $ SC32R-0072SP17 17 Insert Series Insert Series Insert Series Insert Series Drill, Turn, ore & Face With One Tool! Drill meters: MM: 8mm to 32mm Inch:.315 to See Inserts On Following Page

7 INSERTS FOR 4-in-1 INDEXALE DRILLS INSERTS FOR SHARK-CUT INDEXALE DRILLS A Insert Series Manufacturer Reference # AL350 Coated C3/C4 Inserts AM35C Coated C5 Inserts 04 LPNT040104ER RA-04RN04-AL350 $15.75 RA-04RN04-AM35C $ LPNT050204EN RA-05N04-AL350 $15.75 RA-05N04-AM35C $ LPNT060204EN RA-06N04-AL350 $15.75 RA-06N04-AM35C $ LPNT070304EN RA-07N04-AL350 $15.75 RA-07N04-AM35C $ LPNT080304EN RA-08N04-AL350 $16.05 RA-08N04-AM35C $ LPNT09T304EN RA-09N04-AL350 $16.90 RA-09N04-AM35C $ LPNT10T304EN RA-10N04-AL350 $16.90 RA-10N04-AM35C $ LPNT130404EN RA-13N04-AL350 $19.70 RA-13N04-AM35C $ LPNT170508EN RA-17N08-AL350 $19.85 RA-17N08-AM35C $19.85 Insert Series Manufacturer Reference # Arno Rouse Grade AK10 Uncoated C2 Inserts (Wiper) Description Coating Material AL350 COATED C3/C4 TIALN COAT Stainless; High Temp Alloys AK10 UNCOATED C2 UNCOATED Aluminum, Plastics And Non Ferrous AL10 COATED C2-C3 TIALN COAT Super Alloys AM35C COATED C5 TIALN COAT Steels AL10 Coated C2-C3 Inserts (Wiper) 04 LPET040104FR RA-04RE04-AK10 $20.85 RA-04RE04-AL10 $ LPET050204FN RA-05E04-AK10 $20.85 RA-05E04-AL10 $ LPET060204FN RA-06E04-AK10 $20.85 RA-06E04-AL10 $ LPET070304FN RA-07E04-AK10 $20.85 RA-07E04-AL10 $ LPET080304FN RA-08E04-AK10 $21.15 RA-08E04-AL10 $ LPET09T304FN RA-09E04-AK10 $21.45 RA-09E04-AL10 $ LPET10T304FN RA-10E04-AK10 $21.75 RA-10E04-AL10 $ LPET130404FN RA-13E04-AK10 $26.45 RA-13E04-AL10 $ LPET170508FN RA-17E08-AK10 $26.45 RA-17E08-AL10 $30.05 Turning CARIDE INSERTS FULL LINE AVAILALE! Please Call For More Information! Master Catalog 275 DEURRING

8 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES COOLANT THRU INDEXALE DRILLS KOMET QUATRON INDEXALE DRILLS With Combination Straight, Right Hand KOMET FEATURES: High stability and efficiency through the use and positioning of the square inserts. etter chip evacuation and reduced flute erosion through special tool body surface treatment. For difficult drilling conditions such as uneven casting surfaces, hardened steel surfaces and interrupted cut. Outstanding drilled hole quality with reduction in exit marks. Reduced tooling costs through four cutting edges with specially selected substrates and coatings. Inside and outside inserts same insert with the same coating is used, same insert screws. : & Drill : to Drill Depths: 2 X D RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Drill D d Drill Depth 2 X D Length l Drill meter Insert I.C. Flute Length N Shoulder To Tip L Master Catalog NPT KOMET Reference /8 U KQ0562-2D /8 U KQ0593-2D /8 U KQ0625-2D /8 U KQ0656-2D /8 U KQ0687-2D Drill meter Insert I.C /8 U KQ0703-2D /8 U KQ0718-2D /8 U KQ0750-2D /8 U KQ0765-2D /8 U KQ0781-2D /8 U KQ0812-2D /8 U KQ0828-2D /8 U KQ0843-2D Drill meter Insert I.C. $ $ $ /8 U KQ0875-2D /8 U KQ0906-2D /4 U KQ0937-2D /4 U KQ0968-2D $ /4 U KQ0985-2D /4 U KQ1000-2D /4 U KQ1031-2D /4 U KQ1062-2D $ Drill meter Insert I.C /4 U KQ1109-2D /4 U KQ1125-2D /4 U KQ1156-2D /4 U KQ1187-2D /4 U KQ1218-2D /4 U KQ1250-2D /4 U KQ1281-2D Drill meter Insert I.C. $ $ /4 U KQ1312-2D /4 U KQ1328-2D /4 U KQ1375-2D $ /4 U KQ1406-2D /4 U KQ1437-2D /4 U KQ1469-2D /4 U KQ1500-2D /4 U KQ1531-2D $ /4 U KQ1562-2D /4 U KQ1625-2D /4 U KQ1656-2D /4 U KQ1687-2D $ /4 U KQ1750-2D KOMET is a registered trademark of Komet of America, Inc. (See Following Page For Inserts)

9 INDEXALE DRILL INSERTS INDEXALE DRILL INSERTS For KOMET Quatron Drills KOMET GRADES: Grade K84 - Coated C5 Inserts for Drilling Steels, Cast Steels and 400 Series Stainless Grade TialN coated carbide on p40 base with extremely high wear resistence. med to high cutting speed for rough and finish and with interrupt cut. For non-alloy steel, cast steel, die steel rust-proof and stainless steel CHIPREAKERS: Chipbreaker 01 - For good chip control Chipbreaker 13 - For Chip Control Grade K84 - Coated C5, Chipbreaker 01 ISO Code Drill IC T R KOMET Ref. Screws $3.00 each Wrench $8.00 each SOEX W KOM-219-K84-01 $9.23 KOM-N KOM-6IP SOEX W KOM-250-K84-01 $9.37 KOM-N TX-208 SOEX07T W KOM-313-K84-01 $9.61 KOM-N KOM-8IP SOEX W KOM-375-K84-01 $10.49 KOM-N TX-215 SOEX W KOM-500-K84-01 $11.19 KOM-N KOM-20IP Grade TIALN COATED, Chipbreaker 01 ISO Code Drill IC T R KOMET Ref. Screws $3.00 each Wrench $8.00 each SOEX W KOM $9.23 KOM-N KOM-6IP SOEX W KOM $9.37 KOM-N TX-208 SOEX07T W KOM $9.61 KOM-N KOM-8IP SOEX W KOM $10.49 KOM-N TX-215 SOEX W KOM $11.19 KOM-N KOM-20IP Grade K84 - Coated C5, Chipbreaker 13 ISO Code Drill IC T R KOMET Ref. SOEX W KOM-219-K84-13 $9.23 SOEX W KOM-250-K84-13 $9.37 SOEX07T W KOM-313-K84-13 $9.61 SOEX W KOM-375-K84-13 $10.49 SOEX W KOM-500-K84-13 $11.19 KOMET is a registered trademark of Komet of America, Inc. SPEEDS & FEEDS Material Group Tensile strength (lbf/ln2) Hardness H Material Material Example AISI / SAE Cutting speed V ft/min Ø Ø.624 Ø Ø xd Maximum feedrate f, in/rev Ø Ø.843 Ø Ø Ø Ø Ø Ø Ø Ø KOMET Ø Ø CARIDE INSERTS 1 < Unalloyed steel A A Low alloy steel < Lead alloy 12L > High alloy steel heat resistant structural, heat treated, nitride steels > Tool steel H13 H HSS Special alloy: Inconel, Hastelloy, Nimonic, etc. Inconel 718 Nimonic 80A Titanium, Titanium alloy AMS R < Stainless steel: austenitic 300 series 304l < Stainless steel > Stainless steel: martensitic/ferritic 400 series Grey cast iron No 35b No 50 b If you do not see your material listed, please call for our complete speed & feed chart Master Catalog 277 DEURRING

10 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD PALIT INDEXALE DRILLS HIGH SPEED INDEXALE DRILLS 3X & 4X DIAMETER Innovative new design features expanded flute size, resulting in excellent chip evacuation Nickel plated body resists wear, providing longer drill body life Economical, four cutting edges per insert Excellent surface finish Excellent hole diameter repeatability Large range of sizes from.531"-1.938" in both 3X and 4X lengths Drill 17/32 9/16 5/8 11/16 3/4 13/16 7/8 15/ /16 1-1/8 1-3/16 1-1/4 1-5/16 1-3/8 1-7/16 1-1/2 1-9/16 1-5/8 1-11/16 1-3/4 1-13/16 1-7/8 1-15/16 D Ds L1 Ls L Dec. Size Drill Depth Length Drill Description SCI D PL0531-3D $ SCI D PL0531-4D $ SCI D PL0563-3D $ SCI D PL0563-4D $ SCI D PL0625-3D $ SCI D PL0625-4D $ SCI D PL0688-3D $ SCI D PL0688-4D $ SCI D PL0750-3D $ SCI D PL0750-4D $ SCI D PL0813-3D $ SCI D PL0813-4D $ SCI D PL0875-3D $ SCI D PL0875-4D $ SCI D PL0938-3D $ SCI D PL0938-4D $ SCI D PL1000-3D $ SCI D PL1000-4D $ SCI D PL1063-3D $ SCI D PL1063-4D $ SCI D PL1125-3D $ SCI D PL1125-4D $ SCI D PL1188-3D $ SCI D PL1188-4D $ SCI D PL1250-3D $ SCI D PL1250-4D $ SCI D PL1313-3D $ SCI D PL1313-4D $ SCI D PL1375-3D $ SCI D PL1375-4D $ SCI D PL1438-3D $ SCI D PL1438-4D $ SCI D PL1500-3D $ SCI D PL1500-4D $ SCI D PL1563-3D $ SCI D PL1563-4D $ SCI D PL1625-3D $ SCI D PL1625-4D $ SCI D PL1688-3D $ SCI D PL1688-4D $ SCI D PL1750-3D $ SCI D PL1750-4D $ SCI D PL1813-3D $ SCI D PL1813-4D $ SCI D PL1875-3D $ SCI D PL1875-4D $ SCI D PL1938-3D $ SCI D PL1938-4D $ TROULE SHOOTING TIPS FOR SCI INDEXALE DRILLS NEW ITEM! Master Catalog Insert Type SPKX SPKX SPKX07T308 SPKX SPKX SPKX Screw PL $9.81 PL $9.81 PL $9.81 PL $9.81 PL $9.81 PL $9.81 Wrench PL $11.91 PL $11.91 PL $9.86 PL $11.91 PL $11.91 PL $11.91 Problem Some Possible Causes Problem Some Possible Causes Chatter or Vibration Jammed chip Improper insert grade selection Lack of rigidity in set-up Inserts Chipping Inadequate coolant supply Long Chips Incorrect speed and feed rates or reaking Incorrect speed and feed rates High Pitch Noise Incorrect operating conditions Drill is off-center or misaligned Excessive Wear RPM is too high Insert grade is too soft Flank Wear of Inserts Improper insert grade selection Cutting speed is too high

11 PALIT INDEXALE DRILL INSERTS SPKX DRILLING INSERTS For SCI Indexable Drills For Palbit SCI Indexable drills Economical- 4 cutting edges per insert General purpose cutting of steels and stainless steel Drilling Parameters Unalloyed Steel Material NEW ITEM! Grade ISO Range Grade Description PH6920 K10-K25 PVD coated carbide with a micro-grain substrate for machining of medium to hard steel, stainless steels and cast iron PH6930 K30-K45 PVD TiAlN coating provides toughness in steel and stainless steel applications in unfavorable conditions Geometry d S I Ea SPKX PL-197-PH6920 $10.58 SPKX PL-288-PH6920 $12.02 SPKX07T PL-312-PH6920 $12.02 SPKX PL-385-PH6920 $12.69 SPKX PL-453-PH6920 $13.37 SPKX PL-563-PH6920 $14.13 Geometry d S I Ea SPKX PL-197-PH6930 $10.58 SPKX PL-288-PH6930 $12.02 SPKX07T PL-312-PH6930 $12.02 SPKX PL-385-PH6930 $12.69 SPKX PL-453-PH6930 $13.37 SPKX PL-563-PH6930 $14.13 rinell Hardness Grade SFPM Feed Rate inch/rev (Drill meter) PH6920 PH LowCarbon (C= %) Medium Carbon (C= %) High Carbon (C= %) P Non-hardened Low Alloy Steel Hardened Hardened High Alloy Steel Annealed Hardened Cast Steel Low Alloy (alloying elements<5%) High Alloy (alloying elements>5%) Stainless Steel Non-hardened Feritic Hardened Stainless Steel Austenitic M Austenitic Superaustenitic Stainless Steel Non-hardened CastFeritic Hardened Stainless Steel Austenitic Cast Austenitic Hardened Annealed (Iron based) Hi-Temp Aged (Iron ased) S Alloys Annealed (Nickel or Cobalt based) Aged (Nickel or Cobalt ased ) Titanium Pure99.5Ti 400Rm Alloys a+ßalloys 1050Rm H Extra Hard Steel Hardened & tempered 55HRc Malleable Ferritic (short chips) Cast iron Pearlitic (long chips) Gray Low tensile strength K Cast Iron High tensile strength Nodular Feritic Iron Pearlitic non aging Aged Aluminum Alloys Cast N Cast & aged Cast Si13-22% Copper rass Alloys ronze and non leaded Copper Drill Safety Instructions Always keep safety guards in place during entire drill operation Do not touch the tools with bare hands Always wear safety glasses and protective clothing to prevent burns or other injuries Use special tools for removal of hot or sharp chips Operator must have access to a fire extinguisher Clamp work pieces securely Apply recommended cutting conditions for a safe and efficient operation Use adequate ventilation when grinding, some materials produce potentially hazardous dusts Master Catalog 279 CARIDE INSERTS DEURRING

12 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD TUNGALOY STYLE INDEXALE DRILLS INDEXALE DRILLS Coolant Through : to Drill : to Drill Depths: 1 to 6 FEATURES: Exceptional reliability Uses high positive XPMT inserts- Produces a great finish! Manufactured from H-13 steel for greater tool strength Economical-4 cutting edges per insert! 3 different coolant ports Reduce inventory- two insert grades cut everything! Made in the! D S Drill Depth 1.00 Drill Depth 2.00 Drill Depth 3.00 Drill Depth 4.00" and Over Drill. Size QUADEX Drill Drill Drill meter Insert I.C TD $ TD $ TD $ TD $ TD $ TD $ Drill meter Insert I.C TD $ TD $ Master Catalog Drill Drill meter Insert I.C TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ Flute Len. Outside Insert Drill meter Insert I.C TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ Drill meter Insert I.C TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ Drill meter Insert I.C TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ Drill meter Insert I.C TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ TD $ Tungaloy is a registered trademark of Tungaloy of America, Inc. Drill Inside Insert E

13 TUNGALOY STYLE INDEXALE DRILL INSERTS TUNGALOY STYLE INDEXALE INSERTS INSERT FEATURES: High positive XPMT inserts Increased insert thickness and new edge honing increases tool life. Economical! Four cutting edges per insert! 3 grades cut everything! Note: When using inserts with DW chip breaker for high feed drilling set feed rate to 1.5x standard feed rate Drill I. C. T Lengt h Tungaloy Reference No. DJ Chipbreaker AH740 For Steel, Stainless, HiTemp Alloys DS Chipbreaker AH120 For non-ferrous, Stainless, Hi Temp Alloys DS Chipbreaker AH725 For Steel, Alloy steel (High Feed, Alum) to XPMT040104R TO-169-AH740 TO-169-AH120 $8.05 TO-169-AH725 $8.35 SC-03 TX-06F XPMT050204R TO-203-AH740 TO-203-AH120 $8.35 TO-203-AH725 $8.65 SC-04 TX-06F to XPMT06X308R TO-236-AH740 TO-236-AH120 $8.35 TO-236-AH725 $8.65 SC-05 TX-07F to XPMT07H308R TO-276-AH740 TO-276-AH120 $9.00 TO-276-AH725 $9.40 SC-06 TX-08F to XPMT08T308R TO-335-AH740 TO-335-AH120 $12.35 TO-335-AH725 $12.75 SC-07 TX-09F to XPMT110412R TO-441-AH740 TO-441-AH120 $12.35 TO-441-AH725 $12.75 SC-08 TX-15F to XPMT150512R TO-591-AH740 TO-591-AH120 $17.20 TO-591-AH725 $17.80 SC-09 TX-20F RECOMMENDED CUTTING CONDITIONS Work Materials Low Carbon Steels (C<3) JIS SS400,SM490,S25C,etc. Carbon Steels (C<3) JIS S45C,S55C,etc. Low alloy steels JIS SCM415,etc. Alloy Steels JIS SCM440,SCr420,etc. Stainless Steels Austenitic JIS SUS304,SUS316,etc. Stainless steels Martensitic and Ferritic JIS SUS430,SUS416,etc. Stainless Steels Precipitation Hardening JIS SUS630,etc. Gray Cast Irons JIS FC250,etc. Ductile Cast Irons JIS FCD700,etc. Aluminum Alloys JIS A2017,ADC12,etc. Super Alloys Titanium First Choice DS AH725 DJ AH725 DS AH725 DJ AH725 DS AH725 DS AH725 DS AH725 DJ T1015 DJ T1015 High Feed High- Speed - - DW AH725 DS AH DW AH725 DS AH DJ AH725 DJ AH reakage DW AH725 DW AH725 DW AH725 DW AH725 DS AH725 DS AH725 DS AH725 DJ AH725 DJ AH725 Chipbreakers: DJ- For Carbon/Alloy Steels DW- For High Feed Drilling DS- For Stainless Steels Troubleshooting Wear - DJ T DJ T Surface Finish DW AH120 DW AH740 DW AH725 DW AH725 DW AH120 DW AH120 DW A H120 DW AH740 DW AH740 DW AH DS - AH DS - - AH Cutting Speed Vc (SFM) Series L/D INDEXALE DRILL TROULESHOOTING TIPS: Inserts Chipping or reaking- Inadequate coolant supply- Check coolant volume and pressure Speeds and feeds being used are incorrect- Adjust speed and feeds according to tables provided Insert screws may be damaged- Check screw head and thread for nicks and burrs. Do not overtighten screws Inserts not seating properly- Make sure the inserts are seated properly in the pocket bottoms. Clean insert pockets whenever inserts are replaced or indexed making sure no nicks or burrs are present. Misaligned drill/offcenter drill- Check toolholder TIR. Replace or adjust TIR as necessary. Drill not seating properly in tool holder, spindle or turret- Make sure there are no nicks, burrs or chips in tool shank and/or holder. Use a feeler gauge to check parting line between tool shank and socket. Too much tool deflection or lack of tool rigidity due to too much tool overhang- Check if tool can be held shorter. Rough Cutting Action-Tool Makes Rumbling Noise and Deflects- Excessive thrust, Feed rate too high- Lower feed rate and/or increase speed. Chips being recut- Add more coolant flow Screws $1.00 Wrench $2.00 Tungaloy is a registered trademark of Tungaloy of America, Inc. Feed (ipr) D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D D,3D D,5D Master Catalog 281 CARIDE INSERTS DEURRING

14 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES TUNGALOY INDEXALE DRILLS & INSERTS INDEXALE DRILLS Coolant Through FEATURES: Extended drilling capability Ideally balanced drill design for less vibration and chattering Exceptional reliability- Increased insert thickness and new edge honing increases tool life Higher tool economy- four cutting edges per insert can be economically utilized by indexing Unique chip pocket effectively removes chips from center Outside Insert Inside Insert RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD D D1 D2 L1 L2 L Master Catalog Applicable Insert Screw Wrench TO-TDXU $ XPMT040104R SC-03 TX-06F TO-TDXU $ XPMT040104R $1.00 $ TO-TDXU $ XPMT040104R TO-TDXU $ XPMT050204R SC-04 TX-06F TO-TDXU $ XPMT06X308R SC-05 $1.00 TX-07F $ TO-TDXU $ XPMT06X308R TO-TDXU $ XPMT06X308R TO-TDXU $ XPMT07H308R TO-TDXU $ XPMT07H308R TO-TDXU $ XPMT07H308R TO-TDXU $ XPMT08T308R TO-TDXU $ XPMT08T308R TO-TDXU $ XPMT08T308R TO-TDXU $ XPMT08T308R TO-TDXU $ XPMT110412R TO-TDXU $ XPMT110412R TO-TDXU $ XPMT110412R TO-TDXU $ XPMT110412R TO-TDXU $ XPMT110412R TO-TDXU $ XPMT150512R TO-TDXU $ XPMT150512R TO-TDXU $ XPMT150512R TO-TDXU $ XPMT150512R TO-TDXU $ XPMT150512R TO-TDXU $ XPMT150512R TO-TDXU $ XPMT150512R TUNGALOY STYLE INDEXALE INSERTS High positive XPMT inserts Increased insert thickness and new edge honing increases tool life. Economical! Four cutting edges per insert! 3 grades cut everything For speeds & feeds, see previous page Drill I. C. T Lengt h Note: When using inserts with DW chip breaker for high feed drilling set feed rate to 1.5x standard feed rate. Tungaloy Reference No. AH740 DJ AH120 DS AH725 DS For Steel, Stainless, HiTemp Alloys For non-ferrous, Stainless, Hi Temp Alloys SC-06 $1.00 SC-07 $1.00 SC-08 $1.00 SC-09 $1.00 TX-08F $2.00 TX-09F $2.00 TX-15F $2.00 TX-20F $2.00 Chipbreakers: DJ- For Carbon/Alloy Steels DW- For High Feed Drilling DS- For Stainless Steels For Steel, Alloy steel (High Feed, Alum) to XPMT040104R TO-169-AH740 TO-169-AH120 $8.05 TO-169-AH725 $8.35 SC-03 TX-06F XPMT050204R TO-203-AH740 TO-203-AH120 $8.35 TO-203-AH725 $8.65 SC-04 TX-06F to XPMT06X308R TO-236-AH740 TO-236-AH120 $8.35 TO-236-AH725 $8.65 SC-05 TX-07F to XPMT07H308R TO-276-AH740 TO-276-AH120 $9.00 TO-276-AH725 $9.40 SC-06 TX-08F to XPMT08T308R TO-335-AH740 TO-335-AH120 $12.35 TO-335-AH725 $12.75 SC-07 TX-09F to XPMT110412R TO-441-AH740 TO-441-AH120 $12.35 TO-441-AH725 $12.75 SC-08 TX-15F to XPMT150512R TO-591-AH740 TO-591-AH120 $17.20 TO-591-AH725 $17.80 SC-09 TX-20F Screws $1.00 Wrench $2.00

15 SMALL HOLE INDEXALE DRILLS HORNET DRILLS HORNET SMALL DIAMETER INDEXALE DRILLS OTM Stinger Style Flood Coolant INSERTS FEATURES: For smaller diameter holes Drill diameter range: to Up to 2 drill depth Flood coolant Made in Drill to to CUTTING & GRADE INFORMATION IC T R H D F S Indexable Small Hole Drill Accessories Drill Drill Depth OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT OT *OTM & Stinger are trademarks of Manchester OTM Cermet 5NU CT525 P01-P15 US-151 $9.00 US-161 $11.00 Coated 23CU 2025 US-152 $9.00 US-162 $11.00 INSERTS $70.00 $75.00 $75.00 $80.00 Coated 40CU 4025 US-153 $10.72 US-163 $11.00 Screw SC-12 $1.00 SC-11 $1.00 Uncoated 13U 13A US-154 $9.00 US-164 $9.00 INSERT GRADES Super Cermet for semi-roughing to finishing in a wide variety of materials. 5NU Works at higher cutting speeds, providing excellent surface finishes. 13U Sub micron grade for use in High Temp/High Nickel alloys as well as cast iron and aluminum. 23CU Coated Carbide grade for low speed applications and operations requiring toughness. First choice in stainless steels. 40CU Excellent overall Steel and Stainless Steel grade over a wide range, exhibiting good heat and wear resistance For cast iron. Wrench TX-206 $6.50 TX-207 $6.50 D Quantity Discount pcs 10% OFF 30+ pcs 15% OFF CARIDE INSERTS Material Condition Aluminum - Cast Iron, gray - Cast Iron, nodular (ductile) Cast Iron, malleable Steel, low carbon Steel, low carbon - - annealed carburized, Rc Insert Grade SFM FPT 5N N C N C N C N C N C Material Steel, medium carbon Tool Steel 4130, 4140, 4150 Annealed 6150 Annealed Stainless Steel Stainless Steel Condition Insert Grade SFM FPT Rc 5N C annealed 5N Rc 5N N C N C Series 23C C Series 23C C High Temp Alloys Inconel Titanium Alloys Master Catalog 283 DEURRING

16 CHUCK JAWS LATHE WORKHOLDING SPADE DRILL ODIES- SPADE DRILL ODIES Straight, Straight Flute ALLIED TA Series Compatible! MACHINE VISES s Are 50% elow Mfg s List! RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Short Length - Straight Holders, Straight Flute Series A C D E F F G Drill Insert Range (inches) Max Drill Depth Flute Length Ref Length Master Catalog Length Pipe Tap Y 3/8 to 27/64 1 1/4 2-1/32 2 1/8 4 13/32 3/4 2 3/8 1/8 YG-P13Y01 $ Z 7/16 to 1/2 1 1/4 2-1/32 2 1/8 4 13/32 3/4 2 3/8 1/8 YG-P13Z01 $ /64 to 11/16 1 3/8 2-3/ /64 4 9/16 3/4 2 3/8 1/8 YG-P13001 $ /64 to 11/16 1 3/8 2-3/ /64 4 9/16 3/4 2 3/8 1/8 YG-P13051 $ /64 to 15/16 2 5/8 3-7/8 4 1/64 6 7/ /64 to 15/16 2 5/8 3-7/8 4 1/64 6 7/8 2 31/32 to 1 3/8 3 3/8 4-1/2 4 41/ /16 to 1 3/8 3 3/8 4-1/2 4 41/ /32 to 1 7/8 4 3/ / /32 to 2 9/16 5 1/8 6-1/2 6 11/ /2 3/4 3 1/8 YG-P13101 $ /8 YG-P13102 $ /4 3 1/8 YG-P13151 $ /8 YG-P13152 $ /2 1/8 YG-P13202 $ /4 3 1/2 1/8 YG-P13203 $ /2 1/8 YG-P13252 $ /4 3 1/2 1/8 YG-P13253 $ /4 4 1/4 YG-P13303 $ /2 4 1/4 YG-P13304 $ /2 4 1/4 YG-P13404 $ /4 4 1/4 YG-P13405 $ /2 to 3 1/2 6 3/4 8-1/2 8 3/4 12 1/ /2 YG-P13506 $ /32 to 4 1/2 6 3/4 8-7/8 9 1/8 13 7/ /2 YG-P13708 $ Standard Length - Straight Holders, Straight Flute Series A C D E F F G Drill Insert Range (inches) Max Drill Depth Flute Length Ref Length Length Pipe Tap Y 3/8 to 27/64 2 3/8 3-5/32 3 1/4 5 17/32 3/4 2 3/8 1/8 YG-P15Y01 $ Z 7/16 to 1/2 2 3/8 3-5/32 3 1/4 5 17/32 3/4 2 3/8 1/8 YG-P15Z01 $ /64 to 11/16 2 1/2 3-5/ / /16 3/4 2 3/8 1/8 YG-P15001 $ /64 to 11/16 2 1/2 3 5/ / /16 3/4 2 3/8 1/8 YG-P15051 $ /64 to 15/16 6 5/8 7-7/8 8 1/ / /64 to 15/16 6 5/8 7-7/8 8 1/ /8 2 31/32 to 1 3/8 7 3/8 8-1/2 8 41/ /16 to 1 3/8 7 3/8 8-1/2 8 41/ /32 to 1 7/8 8 1/4 9-1/2 9 11/ / /32 to 2 9/16 9 1/8 10-1/ / /2 3/4 3 1/8 YG-P15101 $ /8 YG-P15102 $ /4 3 1/8 YG-P15151 $ /8 YG-P15152 $ /2 1/8 YG-P15202 $ /4 3 1/2 1/8 YG-P15203 $ /2 1/8 YG-P15252 $ /4 3 1/2 1/8 YG-P15253 $ /4 4 1/4 YG-P15303 $ /2 4 1/4 YG-P15304 $ /2 4 1/4 YG-P15404 $ /4 4 1/4 YG-P15405 $ /2 to 3 1/2 10 3/4 12-1/2 12 3/4 16 1/ /2 YG-P15506 $ /32 to 4 1/2 10 3/4 12-7/8 13 1/8 17 7/ /2 YG-P15708 $ ALLIED is a trademart of Allied Machine and Engineering Corporation.

17 SPADE DRILL ODIES- TAPER SHANK SPADE DRILL ODIES Morse Taper, Straight Flute Short Length- Morse Taper, Straight Flute Insert Series A C D E F G Drill Insert Range (inches) Max Drill Depth Flute Length Ref Length MT Pipe Tap Y 3/8-27/64 1-1/4 2-1/ /32 6-5/16 #2 1/16 YG-P01Y02 $ Z 7/16-1/2 1-1/4 2-1/ /32 6-5/16 #2 1/16 YG-P01Z02 $ /64-11/16 1-3/8 2-3/ / /32 #2 1/16 YG-P01002 $ /64-11/16 1-3/8 2-3/ / /32 #2 1/16 YG-P01052 $ /64-15/16 2-3/4 3-7/ /64-15/16 2-3/4 3-7/8 2 31/32-1-3/8 3-3/8 4-1/ /16-1-3/8 3-3/8 4-1/ /32-1-7/8 4-3/ /32-2-9/16 5-1/8 6-1/2 5-39/64 9-5/32 #3 1/8 YG-P01103 $ / /32 #4 1/8 YG-P01104 $ /64 9-5/32 #3 1/8 YG-P01153 $ / /32 #4 1/8 YG-P01154 $ / /32 #3 1/8 YG-P01203 $ / /32 #4 1/8 YG-P01204 $ Coolant Inducer YG-PR1030 YG-PR1031 YG-PR1031 YG-PR / /32 #3 1/8 YG-P01253 $ YG-PR / /16 #4 1/4 YG-P01254 $ YG-PR /8 12-9/16 #4 1/4 YG-P01304 $ YG-PR / /16 #5 1/4 YG-P01305 $ YG-PR /8 13-1/16 #4 1/4 YG-P01404 $ YG-PR /8 14-5/16 #5 1/4 YG-P01405 $ YG-PR /2-3-1/2 6-3/4 8-1/2 11-5/ /16 #5 1/2 YG-P01505 $ YG-PR /32-4-1/2 6-3/4 8-7/ / /16 #5 1/2 YG-P01705 $ YG-PR1054 Standard Length- Morse Taper, Straight Flute Insert Series INTERMEDIATE LENGTH HOLDERS ALLIED TA Series Compatible! A C D E F G Drill Insert Range Max Drill Depth Flute Length Ref Length MT Pipe Tap Y 3/8-27/64 2-3/8 3-5/ / #2 1/16 YG-P03Y02 $ Z 7/16-1/2 2-3/8 3-5/ /32 7-7/16 #2 1/16 YG-P03Z02 $ /64-11/16 2-1/2 3-5/ / /32 #2 1/16 YG-P03002 $ /64-11/16 2 1/2 3-5/ / /32 #2 1/16 YG-P03052 $ /64-15/16 6-3/4 7-7/ /64-15/16 6-3/4 7-7/8 2 31/32-1-3/8 7-3/8 8-1/ /16-1-3/8 7-3/8 8-1/ /32-1-7/8 8-1/4 9-1/ /32-2-9/16 9-1/8 10-1/2 9-39/ /32 #3 1/8 YG-P03103 $ / /32 #4 1/8 YG-P03104 $ / /32 #3 1/8 YG-P03153 $ / /32 #4 1/8 YG-P03154 $ / /32 #3 1/8 YG-P03203 $ / /32 #4 1/8 YG-P03204 $ Coolant Inducer YG-PR1030 YG-PR1031 YG-PR1031 YG-PR / /32 #3 1/8 YG-P03253 $ YG-PR / /16 #4 1/4 YG-P03254 $ YG-PR /8 16-1/16 #4 1/4 YG-P03304 $ YG-PR /8 17-5/16 #5 1/4 YG-P03305 $ YG-PR /8 17-1/16 #4 1/4 YG-P03404 $ YG-PR /8 18-5/16 #5 1/4 YG-P03405 $ YG-PR /2-3-1/2 10-3/4 12-1/2 15-5/ /16 #5 1/2 YG-P03505 $ /32-4-1/2 10-3/4 12-7/ / /16 #5 1/2 YG-P03705 $ Coolant Inducers Are Located On Page 273 YG-PR1054 CARIDE INSERTS Intermediate Length Straight Holder- Straight Flute Series Allied Ref. A C D E Drill Insert Range Max. Drill Depth Flute Length Ref. Length. Length Master Catalog 285 Pipe Tap S - 100L 45/64" - 15/16 4-5/8 5-7/8 6-1/64 8-7/ /8 YG-P14102 $ S - 100L 55/64" - 15/16 4-5/8 5-7/8 6-1/64 8-7/ /8 YG-P14152 $ S - 125L 31/32" - 1-3/8 5-3/8 6-1/2 6-41/ /4 3-1/2 1/8 YG-P14203 $ S - 125L 1-3/16" - 1-3/8 5-3/8 6-1/2 6-41/ /4 3-1/2 1/8 YG-P14253 $ S - 150L 1-13/32" - 1-7/8 6-1/2 7-3/4 7-15/ /4 1-1/2 4 1/4 YG-P14304 $ DEURRING

18 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SPADE DRILL INSERTS-HSS THROW AWAY SPADE DRILL INSERTS Super HSS M4 & T15 HSS M-4: Loose machines Manual machines If T-15 breaks Cross hole drilling HSS T-15: On CNC machines When M-4 life needs to be extended Abrasive drilling ALLIED TA Series Compatible! Inch Dec Series Y 3/32 Thick SUPER HSS T-15 T15 TiN T15 TiAIN $18.00 ea. $21.62 ea. 9.5mm YG-S06Y01 YG-S08Y01 3/ YG-S06Y02 YG-S08Y02 25/ YG-S06Y04 YG-S08Y mm YG-S06Y05 YG-S08Y05 13/ YG-S06Y07 YG-S08Y mm YG-S06Y08 YG-S08Y08 27/ YG-S06Y09 YG-S08Y mm YG-S06Y11 YG-S08Y11 Series Z $18.00 ea. $21.62 ea. 3/32 Thick 7/ YG-S06Z01 YG-S08Z mm YG-S06Z02 YG-S08Z02 29/ YG-S06Z03 YG-S08Z03 15/ YG-S06Z04 YG-S08Z mm YG-S06Z05 YG-S08Z05 31/ YG-S06Z06 YG-S08Z mm YG-S06Z07 YG-S08Z07 1/ YG-S06Z08 YG-S08Z08 Series 0 $19.42 ea. $23.30 ea. 1/8 Thick 13.0mm YG-S06001 YG-S / YG-S06002 YG-S / YG-S06003 YG-S mm YG-S06004 YG-S / YG-S06060 YG-S mm YG-S06005 YG-S / YG-S06006 YG-S mm YG-S06007 YG-S / YG-S06008 YG-S mm YG-S06009 YG-S / YG-S06010 YG-S / YG-S06061 YG-S mm YG-S06011 YG-S / YG-S06012 YG-S mm YG-S06013 YG-S / YG-S06062 YG-S mm YG-S06014 YG-S / YG-S06015 YG-S mm YG-S06016 YG-S / YG-S06063 YG-S / YG-S06017 YG-S mm YG-S06018 YG-S Master Catalog Inch s Are 50% elow Mfg s List! Dec SUPER HSS T-15 SUPER HSS M-4 T15 TiN T15 TiAIN M4 TiN M4 TiAIN Series 1 (cont.) 5/32 Thick $21.85 ea. $25.90 ea. $19.42 ea. $23.30 ea. 45/ YG-S06101 YG-S08101 YG-S01101 YG-S mm YG-S06102 YG-S08102 YG-S01102 YG-S / YG-S06103 YG-S08103 YG-S01103 YG-S mm YG-S06104 YG-S08104 YG-S01104 YG-S / YG-S06105 YG-S08105 YG-S01105 YG-S mm YG-S06106 YG-S08106 YG-S01106 YG-S / YG-S06107 YG-S08107 YG-S01107 YG-S / YG-S06108 YG-S08108 YG-S01108 YG-S mm YG-S06109 YG-S08109 YG-S01109 YG-S / YG-S06110 YG-S08110 YG-S01110 YG-S mm YG-S06111 YG-S08111 YG-S01111 YG-S / YG-S06160 YG-S08160 YG-S01160 YG-S mm YG-S06112 YG-S08112 YG-S01112 YG-S / YG-S06113 YG-S08113 YG-S01113 YG-S mm YG-S06114 YG-S08114 YG-S01114 YG-S / YG-S06115 YG-S08115 YG-S01115 YG-S / YG-S06161 YG-S08161 YG-S01161 YG-S mm YG-S06116 YG-S08116 YG-S01116 YG-S / YG-S06117 YG-S08117 YG-S01117 YG-S / YG-S06162 YG-S08162 YG-S01162 YG-S mm YG-S06118 YG-S08118 YG-S01118 YG-S / YG-S06119 YG-S08119 YG-S01119 YG-S / YG-S06120 YG-S08120 YG-S01120 YG-S / YG-S06121 YG-S08121 YG-S01121 YG-S mm YG-S06122 YG-S08122 YG-S01122 YG-S03122 Series 2 3/16 Thick $25.74 ea. $30.54 ea. $22.84 ea. $27.37 ea. 31/ YG-S06201 YG-S08201 YG-S01201 YG-S / YG-S06202 YG-S08202 YG-S01202 YG-S YG-S06203 YG-S08203 YG-S01203 YG-S / YG-S06204 YG-S08204 YG-S01204 YG-S mm YG-S06205 YG-S08205 YG-S01205 YG-S / YG-S06206 YG-S08206 YG-S01206 YG-S / YG-S06260 YG-S08260 YG-S01260 YG-S / YG-S06207 YG-S08207 YG-S01207 YG-S mm YG-S06208 YG-S08208 YG-S01208 YG-S / YG-S06209 YG-S08209 YG-S01209 YG-S mm YG-S06210 YG-S08210 YG-S01210 YG-S / YG-S06261 YG-S08261 YG-S01261 YG-S / YG-S06211 YG-S08211 YG-S01211 YG-S mm YG-S06212 YG-S08212 YG-S01212 YG-S / YG-S06213 YG-S08213 YG-S01213 YG-S mm YG-S06214 YG-S08214 YG-S01214 YG-S / YG-S06215 YG-S08215 YG-S01215 YG-S / YG-S06216 YG-S08216 YG-S01216 YG-S mm YG-S06217 YG-S08217 YG-S01217 YG-S / YG-S06218 YG-S08218 YG-S01218 YG-S mm YG-S06219 YG-S08219 YG-S01219 YG-S / YG-S06220 YG-S08220 YG-S01220 YG-S mm YG-S06221 YG-S08221 YG-S01221 YG-S / YG-S06222 YG-S08222 YG-S01222 YG-S / YG-S06206 YG-S08206 YG-S01206 YG-S mm YG-S06223 YG-S08223 YG-S01223 YG-S / YG-S06224 YG-S08224 YG-S01224 YG-S / YG-S06225 YG-S08225 YG-S01225 YG-S mm YG-S06226 YG-S08226 YG-S01225 YG-S03226

19 SPADE DRILL INSERTS-HSS THROW AWAY SPADE DRILL INSERTS Super HSS M4 & T15 When to use: HSS M-4: Loose machines Manual machines If T-15 breaks Cross hole drilling HSS T-15: On CNC machines When M-4 life needs to be extended Abrasive drilling COOLANT INDUCERS FOR MORSE TAPER DRILLS Complete with O rings, flat washers and locking clips A C D E I.D. Pipe O.D. Length Thread for Driving Rod s Are 50% elow Mfg s List! Pipe Tap 3/4 1-3/4 7/8 1-3/4 1/8 YG-PR1030 $ /8 1-1/8 2-1/8 1/8 YG-PR1031 $ /4 2-1/2 1-3/8 2-1/2 1/4 YG-PR1042 $ / /8 3 1/4 YG-PR1043 $ /4 3-3/4 1-3/4 3-3/4 1/2 YG-PR1054 $74.19 Inch Series 3 1/4 Thick SUPER HSS T-15 SUPER HSS M-4 Dec T15 TiN T15 TiAIN M4 TiN M4 TiAIN $32.67 ea. $39.17 ea. $28.35 ea. $34.12 ea. 1-13/ YG-S06301 YG-S08301 YG-S01301 YG-S mm YG-S06302 YG-S08302 YG-S01302 YG-S / YG-S06303 YG-S08303 YG-S01303 YG-S mm YG-S06304 YG-S08304 YG-S01304 YG-S / YG-S06305 YG-S08305 YG-S01305 YG-S mm YG-S06306 YG-S08306 YG-S01306 YG-S / YG-S06307 YG-S08307 YG-S01307 YG-S / YG-S06308 YG-S08308 YG-S01308 YG-S mm YG-S06309 YG-S08309 YG-S01309 YG-S / YG-S06310 YG-S08310 YG-S01310 YG-S mm YG-S06311 YG-S08311 YG-S01311 YG-S / YG-S06312 YG-S08312 YG-S01312 YG-S mm YG-S06313 YG-S08313 YG-S01313 YG-S / YG-S06314 YG-S08314 YG-S01314 YG-S mm YG-S06315 YG-S08315 YG-S01315 YG-S / YG-S06316 YG-S08316 YG-S01316 YG-S / YG-S06317 YG-S08317 YG-S01317 YG-S mm YG-S06318 YG-S08318 YG-S01318 YG-S / YG-S06319 YG-S08319 YG-S01319 YG-S mm YG-S06320 YG-S08320 YG-S01320 YG-S / YG-S06321 YG-S08321 YG-S01321 YG-S mm YG-S06322 YG-S08322 YG-S01322 YG-S / YG-S06323 YG-S08323 YG-S01323 YG-S mm YG-S06324 YG-S08324 YG-S01324 YG-S / YG-S06325 YG-S08325 YG-S01325 YG-S / YG-S06326 YG-S08326 YG-S01326 YG-S mm YG-S06327 YG-S08327 YG-S01327 YG-S / YG-S06328 YG-S08328 YG-S01328 YG-S03328 Series 4 5/16 Thick ALLIED TA Series Compatible! $41.34 ea. $49.50 ea. $33.65 ea. $40.37 ea. 1-29/ YG-S06402 YG-S08402 YG-S01402 YG-S / YG-S06404 YG-S08404 YG-S01404 YG-S / YG-S06406 YG-S08406 YG-S01406 YG-S YG-S06407 YG-S08407 YG-S01407 YG-S / YG-S06409 YG-S08409 YG-S01409 YG-S / YG-S06410 YG-S08410 YG-S01410 YG-S / YG-S06411 YG-S08411 YG-S01411 YG-S / YG-S06413 YG-S08413 YG-S01413 YG-S / YG-S06414 YG-S08414 YG-S01414 YG-S / YG-S06416 YG-S08416 YG-S01416 YG-S / YG-S06418 YG-S08418 YG-S01418 YG-S / YG-S06420 YG-S08420 YG-S01420 YG-S / YG-S06422 YG-S08422 YG-S01422 YG-S / YG-S06423 YG-S08423 YG-S01423 YG-S / YG-S06425 YG-S08425 YG-S01425 YG-S / YG-S06427 YG-S08427 YG-S01427 YG-S / YG-S06429 YG-S08429 YG-S01429 YG-S / YG-S06431 YG-S08431 YG-S01431 YG-S / YG-S06432 YG-S08432 YG-S01432 YG-S / YG-S06434 YG-S08434 YG-S01434 YG-S / YG-S06436 YG-S08436 YG-S01436 YG-S / YG-S06438 YG-S08438 YG-S01438 YG-S / YG-S06440 YG-S08440 YG-S01440 YG-S Master Catalog 287 CARIDE INSERTS DEURRING

20 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SPADE DRILL INSERTS-CARIDE THROW AWAY SPADE DRILL INSERTS Carbide Grade Information: C-5-Steel Cutting C-3- Cast Iron C-2- Ductile Iron Stainless Steel Aluminum Exotic Alloys ALLIED Compatible! s Are 50% elow Mfg s List! Series Min-Max Master Catalog Inch Metric Dec TiN C2 TIALN C2 TIN C5 TIALN C5 Series Y Carbide Inserts $31.00 ea. $33.40 ea. $31.00 ea. $33.40 ea YG-S21Y01 YG-S23Y01 YG-S26Y01 YG-S28Y01 3/ YG-S21Y02 YG-S23Y02 YG-S26Y02 YG-S28Y02 Y YG-S21Y03 YG-S23Y03 YG-S26Y03 YG-S28Y03 25/ YG-S21Y04 YG-S23Y04 YG-S26Y04 YG-S28Y04 9.5mm YG-S21Y05 YG-S23Y05 YG-S26Y05 YG-S28Y05 (.374") YG-S21Y06 YG-S23Y06 YG-S26Y06 YG-S28Y06 to 11.07mm 13/ YG-S21Y07 YG-S23Y07 YG-S26Y07 YG-S28Y07 (.436") YG-S21Y08 YG-S23Y08 YG-S26Y08 YG-S28Y08 3/32 Thick 27/ YG-S21Y09 YG-S23Y09 YG-S26Y09 YG-S28Y YG-S21Y10 YG-S23Y10 YG-S26Y10 YG-S28Y YG-S21Y11 YG-S23Y11 YG-S26Y11 YG-S28Y11 Series Z Carbide Inserts $31.00 ea. $33.40 ea. $31.00 ea. $33.40 ea. 7/ YG-S21Z01 YG-S23Z01 YG-S26Z01 YG-S28Z01 Z YG-S21Z02 YG-S23Z02 YG-S26Z02 YG-S28Z02 29/ YG-S21Z03 YG-S23Z03 YG-S26Z03 YG-S28Z mm 15/ YG-S21Z04 YG-S23Z04 YG-S26Z04 YG-S28Z04 (.437") YG-S21Z05 YG-S23Z05 YG-S26Z05 YG-S28Z05 to (.510) 31/ YG-S21Z06 YG-S23Z06 YG-S26Z06 YG-S28Z06 3/32 Thick YG-S21Z07 YG-S23Z07 YG-S26Z07 YG-S28Z07 1/ YG-S21Z08 YG-S23Z08 YG-S26Z08 YG-S28Z08 Series 0 Carbide Inserts $34.37 ea. $37.00 ea. $34.37 ea. $37.00 ea YG-S21001 YG-S23001 YG-S26001 YG-S / YG-S21002 YG-S23002 YG-S26002 YG-S / YG-S21003 YG-S23003 YG-S26003 YG-S YG-S21004 YG-S23004 YG-S26004 YG-S / YG-S21060 YG-S23060 YG-S26060 YG-S YG-S21005 YG-S23005 YG-S26005 YG-S / YG-S21006 YG-S23006 YG-S26006 YG-S YG-S21007 YG-S23007 YG-S26007 YG-S / YG-S21008 YG-S23008 YG-S26008 YG-S YG-S21009 YG-S23009 YG-S26009 YG-S / YG-S21010 YG-S23010 YG-S26010 YG-S28010 (.511") 39/ YG-S21061 YG-S23061 YG-S26061 YG-S28061 to YG-S21011 YG-S23011 YG-S26011 YG-S28011 (.695") YG-S21064 YG-S23064 YG-S26064 YG-S /8 Thick 5/ YG-S21012 YG-S23012 YG-S26012 YG-S YG-S21013 YG-S23013 YG-S26013 YG-S / YG-S21062 YG-S23062 YG-S26062 YG-S YG-S21014 YG-S23014 YG-S26014 YG-S / YG-S21015 YG-S23015 YG-S26015 YG-S YG-S21016 YG-S23016 YG-S26016 YG-S / YG-S21063 YG-S23063 YG-S26063 YG-S / YG-S21017 YG-S23017 YG-S26017 YG-S YG-S21018 YG-S23018 YG-S26018 YG-S28018 Series 1 Carbide Inserts $39.17 ea. $42.29 ea. $39.17 ea. $42.29 ea (.690") to (.960") 5/32 Thick 45/ YG-S21101 YG-S23101 YG-S26101 YG-S YG-S21102 YG-S23102 YG-S26102 YG-S / YG-S21103 YG-S23103 YG-S26103 YG-S YG-S21104 YG-S23104 YG-S26104 YG-S / YG-S21105 YG-S23105 YG-S26105 YG-S YG-S21106 YG-S23106 YG-S26106 YG-S / YG-S21107 YG-S23107 YG-S26107 YG-S / YG-S21108 YG-S23108 YG-S26108 YG-S YG-S21109 YG-S23109 YG-S26109 YG-S / YG-S21110 YG-S23110 YG-S26110 YG-S YG-S21111 YG-S23111 YG-S26111 YG-S / YG-S21160 YG-S23160 YG-S26160 YG-S YG-S21112 YG-S23112 YG-S26112 YG-S / YG-S21113 YG-S23113 YG-S26113 YG-S YG-S21114 YG-S23114 YG-S26114 YG-S / YG-S21115 YG-S23115 YG-S26115 YG-S / YG-S21161 YG-S23161 YG-S26161 YG-S YG-S21116 YG-S23116 YG-S26116 YG-S / YG-S21117 YG-S23117 YG-S26117 YG-S / YG-S21162 YG-S23162 YG-S26162 YG-S YG-S21118 YG-S23118 YG-S26118 YG-S / YG-S21119 YG-S23119 YG-S26119 YG-S / YG-S21120 YG-S23120 YG-S26120 YG-S / YG-S21121 YG-S23121 YG-S26121 YG-S YG-S21122 YG-S23122 YG-S26122 YG-S28122

21 SPADE DRILL INSERTS-CARIDE THROW AWAY SPADE DRILL INSERTS Carbide Grade Information: C-5-Steel Cutting C-3- Cast Iron C-2- Ductile Iron Stainless Steel Aluminum Exotic Alloys s Are 50% elow Mfg s List! Series Min-Max Inch Metric Dec TiN C2 TIALN C2 TIN C5 TIALN C5 Series 2 Carbide Inserts $46.37 ea. $49.99 ea. $46.37 ea. $49.99 ea (.961") to (1.380") 3/16 Thick 31/ YG-S21201 YG-S23201 YG-S26201 YG-S / YG-S21202 YG-S23202 YG-S26202 YG-S YG-S21203 YG-S23203 YG-S26203 YG-S / YG-S21204 YG-S23204 YG-S26204 YG-S YG-S21205 YG-S23205 YG-S26205 YG-S / YG-S21206 YG-S23206 YG-S26206 YG-S / YG-S21260 YG-S23260 YG-S26260 YG-S / YG-S21207 YG-S23207 YG-S26207 YG-S YG-S21208 YG-S23208 YG-S26208 YG-S / YG-S21209 YG-S23209 YG-S26209 YG-S YG-S21210 YG-S23210 YG-S26210 YG-S / YG-S21261 YG-S23261 YG-S26261 YG-S / YG-S21211 YG-S23211 YG-S26211 YG-S YG-S21212 YG-S23212 YG-S26212 YG-S / YG-S21213 YG-S23213 YG-S26213 YG-S YG-S21214 YG-S23214 YG-S26214 YG-S / YG-S21215 YG-S23215 YG-S26215 YG-S / YG-S21216 YG-S23216 YG-S26216 YG-S YG-S21217 YG-S23217 YG-S26217 YG-S / YG-S21218 YG-S23218 YG-S26218 YG-S YG-S21219 YG-S23219 YG-S26219 YG-S / YG-S21220 YG-S23220 YG-S26220 YG-S YG-S21221 YG-S23221 YG-S26221 YG-S / YG-S21222 YG-S23222 YG-S26222 YG-S YG-S21223 YG-S23223 YG-S26223 YG-S / YG-S21224 YG-S23224 YG-S26224 YG-S / YG-S21225 YG-S23225 YG-S26225 YG-S YG-S21226 YG-S23226 YG-S26226 YG-S28226 Series 3 Carbide Inserts $72.10 ea. $75.94 ea. $72.10 ea. $75.94 ea to /4 Thick ALLIED TA Series Compatible! 1-13/ YG-S21301 YG-S23301 YG-S26301 YG-S YG-S21302 YG-S23302 YG-S26302 YG-S / YG-S21303 YG-S23303 YG-S26303 YG-S YG-S21304 YG-S23304 YG-S26304 YG-S28304 "1-15/ YG-S21305 YG-S23305 YG-S26305 YG-S YG-S21306 YG-S23306 YG-S26306 YG-S / YG-S21307 YG-S23307 YG-S26307 YG-S / YG-S21308 YG-S23308 YG-S26308 YG-S YG-S21309 YG-S23309 YG-S26309 YG-S / YG-S21310 YG-S23310 YG-S26310 YG-S YG-S21311 YG-S23311 YG-S26311 YG-S / YG-S21312 YG-S23312 YG-S26312 YG-S YG-S21313 YG-S23313 YG-S26313 YG-S / YG-S21314 YG-S23314 YG-S26314 YG-S YG-S21315 YG-S23315 YG-S26315 YG-S / YG-S21316 YG-S23316 YG-S26316 YG-S / YG-S21317 YG-S23317 YG-S26317 YG-S YG-S21318 YG-S23318 YG-S26318 YG-S / YG-S21319 YG-S23319 YG-S26319 YG-S YG-S21320 YG-S23320 YG-S26320 YG-S / YG-S21321 YG-S23321 YG-S26321 YG-S YG-S21322 YG-S23322 YG-S26322 YG-S / YG-S21323 YG-S23323 YG-S26323 YG-S YG-S21324 YG-S23324 YG-S26324 YG-S / YG-S21325 YG-S23325 YG-S26325 YG-S / YG-S21326 YG-S23326 YG-S26326 YG-S YG-S21327 YG-S23327 YG-S26327 YG-S / YG-S21328 YG-S23328 YG-S26328 YG-S Master Catalog 289 CARIDE INSERTS DEURRING

22 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING SPADE DRILL INSERTS-FLAT OTTOM FLAT OTTOM SPADE DRILL INSERTS SUPER COALT T-15 NEW ITEM! s Are 50% elow Mfg s List! SPEED & FEEDS CUTTING CONDITIONS FOR T-15 FLAT OTTOM SPADE DRILL INSERTS Series Min-Max Y.374" to.436" 3/32" thick Z.437" to.510" 3/32" thick 0.511" to.695" 1/8" thick 1.690" to.960" 5/32" thick 2.961" to 1.380" 3/16" Thick Inch Dec. TiN Coated TiAlN Coated 3/ YG-SF05024 $27.08 YG-SF15024 $ / YG-SF05026 $27.08 YG-SF15026 $ / YG-SF05028 $27.08 YG-SF15028 $ / YG-SF05030 $27.08 YG-SF15030 $ / YG-SF05032 $27.08 YG-SF15032 $ / YG-SF05034 $29.56 YG-SF15034 $ / YG-SF05036 $29.56 YG-SF15036 $ / YG-SF05038 $29.56 YG-SF15038 $ / YG-SF05040 $29.56 YG-SF15040 $ / YG-SF05042 $29.56 YG-SF15042 $ / YG-SF05044 $29.56 YG-SF15044 $ / YG-SF05046 $32.97 YG-SF15046 $ / YG-SF05048 $32.97 YG-SF15048 $ / YG-SF05050 $32.97 YG-SF15050 $ / YG-SF05052 $32.97 YG-SF15052 $ / YG-SF05054 $32.97 YG-SF15054 $ / YG-SF05056 $32.97 YG-SF15056 $ / YG-SF05058 $32.97 YG-SF15058 $ / YG-SF05060 $32.97 YG-SF15060 $ / YG-SF05062 $38.01 YG-SF15062 $ YG-SF05100 $38.01 YG-SF15100 $ / YG-SF05102 $38.01 YG-SF15102 $ / YG-SF05104 $38.01 YG-SF15104 $ / YG-SF05106 $38.01 YG-SF15106 $ / YG-SF05108 $38.01 YG-SF15108 $ / YG-SF05110 $38.01 YG-SF15110 $ / YG-SF05112 $38.01 YG-SF15112 $ / YG-SF05114 $38.01 YG-SF15114 $ / YG-SF05116 $38.01 YG-SF15116 $ / YG-SF05118 $38.01 YG-SF15118 $ / YG-SF05120 $38.01 YG-SF15120 $ / YG-SF05122 $38.01 YG-SF15122 $ / YG-SF05124 $38.01 YG-SF15124 $42.86 ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Material Material Hardness (hn) Speed (SFM) Tin TiAlN 3/8-1/2 33/64-11/ Master Catalog Feed 45/64-15/16 31/32-1-3/8 Free Machining Steel , 12L13, L14, Low Carbon Steel , 1020, Medium Carbon , 1050, , Structural Steel A36, A A Cast Iron/SG Iron A48-76 GR30/GR A A GR Material Material Hardness (hn) Speed (SFM) Tin TiAlN 3/8-1/2 33/64-11/16 Feed 45/64-15/16 31/32-1-3/8 Alloy Steel , 4130, , Tool Steel H13, H21, A2, S High Temp. Alloy Hastelloy, Inconel High Strength Alloys , V etc Aluminum , 6061, Stainless Steel , 316, 410, The recommendations for speeds, feeds and other parameters presented in this chart are nominal recommendations and should be considered only as good starting points. Speed and feed reductions (20% reduction in speed and 10% reduction in feed) are recommended.

23 SPADE DRILL ACCESSORIES TORX SCREWS & DRIVERS Screws sold in packages of 10 Series Item Torx Screw Torx Screw (Nylon Locking) Premium Torx Driver Per Pkg Item Per Pkg Item Inch/Metric Drill Range Y 2XT7 YG-J7Y001 $ XT7N YG-J7Y006 $18.19 T7 YG-J5Y007 $6.05 3/8 to 27/64 9 to 11 Z 2LXT7 YG-J7Z011 $ LXT7N YG-J7Z016 $18.19 T7 YG-J5Y007 $6.05 7/16 to 1/ to XT8 YG-J80021 $ XT8N YG-J80026 $17.07 T8 YG-J50008 $ /64 to 11/ to LXT8 YG-J80531 $ LXT8N YG-J80536 $17.97 T8 YG-J50008 $ /64 to 11/ to XT9 YG-J91041 $ XT9N YG-J91046 $17.07 T9 YG-J51009 $ /64 to 15/ to LXT9 YG-J91551 $ LXT9N YG-J91556 $17.97 T9 YG-J51009 $ /64 to 15/ to XT15 YG-J2061 $ XT15N YG-J2066 $17.97 T15 YG-J52015 $ /32 to 1 3/ to XT15 YG-J2061 $ XT15N YG-J2066 $17.97 T15 YG-J52015 $ /16 to 1 3/ to XT20 YG-JC3081 $ XT20N YG-JC3086 $17.97 T20 YG-J53020 $ /32 to 2 9/ to XT25 YG-JD5091 $ XT25N YG-JD5096 $20.37 T25 YG-J55025 $ /2 to 3 1/ to SPEEDS/FEEDS AND COATING RECOMMENDATIONS Material Free Machining Steel 1118, 1215, 12L14, etc. Low & Medium Carbon Steel 1018, 1040, 1140, etc. Alloy Steel 4140, 5140, 8640, etc. High Strength Alloy Steel 4340, 4330V, 300M, etc. Structural Steel A36, A285, A516, etc. High Temp, Alloy Hastelloy, Inconel 600, etc. Stainless Steel 303, 416, 420, 17-4 PH, etc. Tool Steel H-13, H021, A04, 0-2, S-3, etc. Aluminum Cast Iron Gray, Ductile, Nodular Material Hardness (HN) Coating SFM 3/8" to 1/2 33/64" to 11/16 45/64" to 15/16 Feed (IPR) 31/32" to 1-3/8 1-13/32" to 1-7/8 1-29/32" to 2-9/ /32" to 4-1/2" Super TiN Hardslick Super TiALN Super TiN Hardslick Super TiALN Super TiN Super TiALN Super TiN Super TiALN Super TiN Hardslick Hardslick Super TiALN Hardslick Super TiALN Note: On many materials two or sometimes all three coatings will interchange with excellent performance Master Catalog 291 CARIDE INSERTS DEURRING

24 CHUCK JAWS LATHE WORKHOLDING ORING ARS, OD TURNING HOLDERS & INSERTS INDEX RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD MACHINE VISES ORING - STEEL, HEAVY METAL & CARIDE ORING ARS & INSERTS TURNING - OD *Circle, Kennametal, Sandvik, Sumitomo, Mitsubishi, Iscar, Palbit and TMX are trademarks of their respective companies Master Catalog Page MITSUISHI Style oring ars - Min. ore SWLOR ars & WCMT (80 Trigon) Inserts 293 CIRCLE Style Mini oring ars - Min ore & CDCD (80 mond) inserts CIRCLE Style Mini oring ars - Min ore & TDA (60 Triangle) inserts 296 KENNAMETAL Style oring ars - Min bore SCLPR ars using CPMT (80 mond) inserts 297 CPMT (80 mond) Inserts - TUNGALOY & Mitsubishi 297 KENNAMETAL Style oring ars - Min bore STUPR & STFPR ars using TPMT (60 Triangle) 298 TPMT (60 Triangle) Inserts - TUNGALOY & Mitsubishi 299 SANDVIK Style oring ars - Min bore SCLCR ars using CCMT (80 mond) inserts 300 CCMT (80 mond) Inserts - TUNGALOY 301 SANDVIK Style oring ars - Min bore SDUCR ars using DCMT (55 mond) inserts 302 DCMT (55 mond) Inserts - TUNGALOY 303 SANDVIK Style oring ars - Min bore STFCR/STUCR ars using TCMT (60 Triangle) inserts 304 TCMT (60 Triangle) Inserts - TUNGALOY 305 SUMITOMO Style oring ars - Min bore STJOR ars & TGP/TPGP/TPGG (60 Triangle) 306 SUMITOMO Style oring ars - Min. ore SCLOR ars & CPGP/CPGM (80 mond) Inserts 307 SVUCR/L, SWUCR/L, CTFPR oring ars-tmx NEW! 308 Micro 100 Coolant Thru oring ars 309 ig oring ars - Industry Standard - SI-MVUNR/L, SI-MWLNR/L, SI-MTUNR/L DORIAN Coolant Thru oring ars 312 ACKFACING ars using DCMT Inserts DCMT (55 mond) inserts 313 OD Turning Holders - MCLNR, ACLNR 314 OD Turning Holders - MCRNR, MDPNN, MSDNN 315 OD Turning Holders - MDJNR, ADJNR/L, MTANR/L 316 OD Turning Holders - MTENNS, MTFNR/L, MTGNR/L 317 OD Turning Holders - ATGNR/L, MTJNR/L, MVJNR/L 318 OD Turning Holders - MWLNR/L, AWLNR/L 319 SWISS style - OD Turning Holders 320 Chrome Nickel Turning Holders-MICRO OD Toolholder s 323 CARIDE & CERMET TURNING & ORING INSERTS TOSHIA TUNGALOY Insert Grades and Chipbreakers 324 CNMG Inserts CCMT Inserts 331 CPMT Inserts 332 DNMG Inserts 329 DCMT & DCGT Inserts 327 SNMG Inserts 333 TNMG Inserts 328 TCMT Inserts 336 VNMG & VNGG Inserts 329 WNMG Inserts 330 POSITIVE ORING INSERTS-TUNGALOY NEGATIVE TURNING INSERTS-TUNGALOY PALIT Turning Inserts- NEW! KORLOY Inserts for Aluminum 338 ISCAR Inserts 335

25 MITSUISHI STYLE ORING ARS SWLOR_ ORING ARS Using WCMT Inserts Uses WCMT type inserts s have locating flats for easy set-up Available in steel, heavy metal or carbide shanks See following page for inserts Made in the Insert WCMT WCMT -S032 WCMT Reference D Min ore _SWLOR _SWLOR _SWL0502RS _SWLOR _SWL0504R _SWLOR _SWLOR _SWLOR Steel -4xD Heavy Metal-6xD Carbide -8xD L 5 5 M-1000R $39.00 M-1010R $39.00 M-1020R $39.00 M-1030R $39.00 M-1040R $39.00 M-1050R $39.00 M-1060R $39.00 M-1070R $45.00 M-1080R _SWLOR WCMT $ T3 M-1090R _SWLOR $58.00 *Mitsubishi is a trademark of Mitsubishi Materials U.S.A. Corporation WCMT/WCGT INSERTS GRADE US-735: for continuous & interrupted cutting of steels & stainless steels. TiAlN Coated: For high temp alloys and stainless steel. *Mitsubishi is a trademark of Mitsubishi Materials U.S.A. Corporation ars Using WCMT/WCGT WCMT/WCGT -S302 WCMT/WCGT WCMT/WCGT -06T3 VENTURE II SAFETY GLASSES Min ore L IC T R 5/ / / / /16 3/32 3/32 5/ (1/128).015 (1/64).008 (1/128).015 (1/64).008 (1/128).015 (1/64).015 (1/64).032 (1/32) M-3000R $94.00 M-3010R $94.00 M-3020R $ M-3030R $ M-3040R $ M-3050R $ M-3060R $ M-3070R $ M-3080R $ M-3090R $ Reference 9.75 base curved lens provides full side protection without distracting seams or traditional type side shields Nose buds secure the glass and prevent slipping while providing a pillow soft fit Temples adjust to four different lengths Lenses are coated for superior scratch resistance Lenses provide 99% protection against harmful UV rays Exceeds ANSI Z standards CE EN166 and CAN/CSA Z certified Min ore Master Catalog 293 L Grade M-5000R $ M-5010R $ M-5020R $ M-5030R $ M-5040R $ M-5050R $ M-5060R $ M-5070R $ M-5080R $ M-5090R $ Screw $1.00 SC-22 SC-21 SC-22 SC-21 SC-23 SC-24 Torx Wrench $5.00 TX-206 T6 TX-208 T8 TX-215 T15 rand WCMT US-735 M-501 $8.75 Mitsubishi WCGT TiAlN US-901 $9.25 USST WCMT US-735 M-511 $8.75 Mitsubishi WCGT TiAlN US-902 $9.25 USST WCMTS30202 US-735 M-521 $8.75 Mitsubishi WCGTS30202 TiAlN US-903 $9.25 USST WCMTS30204 US-735 M-531 $8.75 Mitsubishi WCGTS30204 TiAlN US-904 $9.25 USST WCMT US-735 M-541 $8.75 Mitsubishi WCGT TiAlN US-905 $9.25 USST WCMT US-735 M-551 $8.75 Mitsubishi WCGT TiAlN US-906 $9.25 USST WCMT06T304 US-735 M-561 $10.50 Mitsubishi WCGT06T304 TiAlN US-907 $11.75 USST WCMT06T308 US-735 M-571 $10.50 Mitsubishi WCGT06T308 TiAlN US-908 $11.75 USST Frame Color lack Lens Color MITSUISHI Using WCMT Inserts Clear PYR-S1810S $4.39 Gray PYR-S1820S $4.99 lue PYR-S1860S $4.99 Amber PYR-S1830S $4.99 D CARIDE INSERTS DEURRING

26 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD CIRCLE STYLE MINI ORING ARS USING DIAMOND SHAPED CDCD INSERTS Minimum bore: lead angle lead angle lead angle Uses CDCD type inserts s have locating flats for easy set-up Available in steel, heavy metal or carbide shanks See following page for inserts Made in the Min ore A Depth C Fig # Steel -4xD Heavy Metal-6xD Carbide -8XD Master Catalog C-3000R $ C-5005R $ C-1010R $ C-1015R $ C-1020R $ C-3025R $ C-3030R $ C-5035R $ C-1045R $ C-3050R $94.00 C-5050R $ C-1060R $ C-1065R $ C-1070R $ C-1075R $ C-1080R $ C-1085R $ C-3090R $ C-3095R $ C-5100R $ C-5105R $ C-1110R $ C-3115R $94.00 C-5115R $ C-1125R $ C-1130R $ C-1135R $ C-1140R $ C-1145R $ C-1150R $ C-3155R $ C-3160R $ C-5165R $ C-5170R $ *Circle is a registered trademark of Circle Machine Company DENIM SHOP APRONS 100% blue cotton denim E version includes waist pocket PR version includes chest pocket w/ pen holder One size fits all 35 length x 28 wide Description Denim Apron w/ Chest Pocket SHOP-APRON-PR $7.99 Denim Apron w/ Waist Pocket SHOP-APRON-E $5.99 DISPOSALE EARPLUGS NRR 31db CE EN-352-2:2002 certification Contoured fit, disposable polyurethane ear plugs Plug gently expands and selfadjusts to all size ear canals Available corded or uncorded in convenient dispenser box Fig 1 Fig 2 Screws Wrench $1.00 TX-206 $5.00 Description Pack Size Disposable Uncorded Earplugs 200/box PYR-DP1000 $25.00 Disposable Corded Earplugs 100/box PYR-DP1001 $25.00 D

27 CIRCLE STYLE MINI ORING ARS USING DIAMOND SHAPED CDCD INSERTS Lead angle: 5 Minimum bore:.290 Uses CDCD type inserts s have locating flats for easy set-up Available in steel, heavy metal or carbide shanks See bottom of page for inserts Made in the Min ore.290 A oring Depth C Fig # Steel -4xD Heavy Metal-6xD Carbide -8XD C-1175R $ C-3180R $94.00 C-5180R $ C-5185R $ C-1200R $ C-1205R $ C-1210R $ C-1215R $ C-1220R $ C-1225R $ C-3230R $ C-3235R $ C-5240R $ C-5245R $ *Circle is a registered trademark of Circle Machine Company CDCD INSERTS Fig 1 Fig 2 Screws $1.00 Wrench $ TX-206 C D GRADE SELECTION CHART I.C. T R Uncoated CM2 C1/C2 US-701 $8.00 US-702 $8.00 US-703 $8.00 Coated CVM2 C1/C2 US-711 $8.75 US-712 $8.75 US-713 $8.75 Uncoated CS7 C6/C7 US-706 $8.00 US-707 $8.00 US-708 $8.00 Coated CV7 C6/C7 US-721 $8.75 US-722 $8.75 US-723 $8.75 Grade Coating Material Operation CM2 Uncoated Non Ferrous Alloys, High Strength Steel Alloys Finish CVM2 TiN Coated Non Ferrous materials, Stainless Steels Semi-finish, Finish CS7 UnCoated Carbon Steels, Alloy Steels, Tool Steels Semi-finish CV7 TiN Coated Steels, Stainless Steels Semi FInish, Finish TL120 TiAlN Coated High Temp Alloys, Stainless Steels Semi FInish, Finish DIGIT COUNTER MICROMETERS.0001/.001 GRADUATION.001" is read directly from the counter,.0001" is read on the micrometer sleeve Steel or carbide measuring face Ratchet stop and lock nut alanced frame design for comfortable and accurate measuring Extremely hard and stable one-piece spindle Micro-lapped anvil and spindle faces Coated TL120 US-731 $9.95 US-732 $9.95 US-733 $9.95 Range Graduation Face Model 0-1".001 Steel 216RL-1 STR $ ".001 Steel 216RL-2 STR $ ".001 Steel 216RL-3 STR $ ".001 Steel 216RL-4 STR $ ".0001 Carbide 216XRL-1 STR $ ".0001 Carbide 216XRL-2 STR $ ".0001 Carbide 216XRL-3 STR $ ".0001 Carbide 216XRL-4 STR $ Master Catalog 295 A CARIDE INSERTS DEURRING

28 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS CIRCLE STYLE MINI ORING ARS USING TRIANGLE SHAPED TDA INSERTS Minimum bore:.270 to.360 Uses TDA type inserts s have locating flats for easy set-up Available in steel, heavy metal or carbide shanks See bottom of page for inserts Made in the Min ore A oring Depth C Fig # Steel -4xD Heavy Metal-6xD Carbide -8xD C-1300R $ C-3305R $ C-1315R $ C-1320R $ C-1330R $ C-1335R $ C-3340R $ C-3345R $ C-5350R $ C-5355R $ C-1360R $40.00 C-3360R $ C-1370R $ C-1375R $ C-1380R $ C-1385R $ C-3390R $ C-3395R $ C-5400R $ C-5405R $ C-1410R $40.00 C-3410R $ C-5415R $ C-1420R $ C-1425R $ C-1430R $ C-1435R $ C-3440R $ C-3445R $ C-5450R $ C-5455R $ *Circle is a registered trademark of Circle Machine Company TDA TYPE INSERTS Fig 1 Fig 2 Screws $1.00 Wrench $ TX-206 C D ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD GRADE SELECTION CHART Uncoated CM2 C1/C2 Coated CVM2 C1/C Master Catalog Uncoated CS7 C6/C7 Coated CV7 C6/C7 Coated TL120 I.C. T R $8.00 ea $8.75 ea $8.00 ea $8.75 ea $9.95 ea US-751 US-761 US-756 US-771 US US-752 US-762 US-757 US-772 US US-753 US-763 US-758 US-773 US-783 Grade Coating Material Operation CM2 Uncoated Non Ferrous Alloys, High Strength Steel Alloys Finish CVM2 TiN Coated Non Ferrous materials, Stainless Steels Semi-finish, Finish CS7 UnCoated Carbon Steels, Alloy Steels, Tool Steels Semi-finish CV7 TiN Coated Steels, Stainless Steels Semi FInish, Finish TL120 TiAlN Coated High Temp Alloys, Stainless Steels Semi FInish, Finish

29 SCLPR ORING ARS USING CPMT INSERTS KENNAMETAL STYLE SCLPR ORING ARS Industry standard SCLPR type Uses CPMT type inserts s have locating flats for easy set-up Available in steel, heavy metal or carbide shanks See bottom of page for inserts Made in the Insert CPMT 21.5_ CPMT 32.5_ Kennametal Reference _06-SCLPR-2 _08-SCLPR-2 _10-SCLPR-2 _08-SCLPR-3 _10-SCLPR-3 _12-SCLPR-3 D.375 (3/8).500 (1/2).625 (5/8).500 (1/2).625 (5/8).750 (3/4) Fig # Min ore Steel -4xD Heavy Metal-6xD Carbide -8xD L _16-SCLPR (1-2) (2) Kennametal is a registered trademark of Kennametal Inc. CPMT INSERTS SS CS S CI AL NF GT SA IN R M F LEGEND Material Stainless Steel Carbon Steel Steel Cast Iron Aluminum Non-Ferrous Material General Turning Super Alloys Inconel Operation Roughing Medium Finishing ars Using CPMT21.5_ (CPMT 0602 ) ars Using CPMT32.5_ (CPMT 09T3 ) 7.0 IC T R / /32 K-1010R $39.00 K-1020R $45.00 K-1030R $50.00 K-1040R $45.00 K-1050R $50.00 K-1060R $58.00 K-1070R $85.00 Min ore L K-3010R $ K-3020R $ K-3030R $ Min ore Master Catalog 297 L (1) 10.0 CPMT I.C.-size T-thickness R-radius IC T R / /32 Fig 1 Fig 2 Chip breaker Oper. K-3050R $ K-3060R $ K-3070R $ (1) 12.0 K-5010R $ K-5020R $ K-5030R $ K-5040R $ K-5050R $ K-5060R $ K-5070R $ Screw $ 1.00 SC-31 SC-32 Wrench $ 5.00 TX-207 TX-215 TUNGALOY MITSUISHI INSERTS [] S, SS S, SS S, SS SS, CS S, CI AL, NF GT AT530 NS530 T9025 CERMET COATED CARIDE US-735 $12.95 UC-6010 $12.95 COATED CARIDE HTi20T $12.95 UNCOATED CARIDE AP25N $12.95 CERMET SQ F M-211 M-212 M-213 M-214 PS F to M TO-1551 TO-1552 TO-3563 $5.60 $4.73 $ MQ R M-221 M-222 M-223 M-224 SQ F M-231 M-232 M PS F to M TO-1554 TO-1555 TO-3564 $5.60 $3.68 $ MQ R M-241 M-242 M-243 M-244 SQ F M-251 M-252 M Chip breaker Oper. AT530 NS530 T9025 CERMET COATED CARIDE US-735 $10.95 UC-6010 $10.95 COATED CARIDE MITSUISHI uy In ox Quantities & Save! HTi20T $8.00 UNCOATED CARIDE AP25N $8.95 CERMET SQ F M MQ R M M-313 M-314 SQ F M-321 M-322 M-323 PS F to M TO-1557 TO $5.92 $ MQ R M-331 M-332 M-333 M-334 SQ F M-341 M-342 M-343 PS F to M TO-1560 TO-1561 TO $5.92 $4.93 $ MQ R M-351 M-352 M-353 M-354 SQ F M-361 M-362 M-363 PS F to M TO-1563 TO-1564 TO $5.92 $4.93 $6.16 D CARIDE INSERTS DEURRING

30 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD STUPR/STFPR ORING ARS USING TPMT INSERTS KENNAMETAL STYLE STUPR & STFPR ORING ARS Industry standard STUPR & STFPR type STUPR: 3 lead angle, STFPR: 0 Uses TPMT type inserts s have locating flats Available in steel, heavy metal or carbide shanks Please see following page for inserts Made in the Insert TPMT 21.5_ TPMT 32.5_ Steel Heavy Metal Carbide (See inserts on following page) 4 x meter 6 x meter 8 x meter Kennametal Reference _06-STUPR-2 _08-STUPR-2 _10-STUPR-2 _06-STFPR-2 _08-STFPR-2 _10-STFPR-2 _12-STFPR-3 D.375 (3/8).500 (1/2).625 (5/8).375 (3/8).500 (1/2).625 (5/8).750 (3/4) Fig # Min ore Master Catalog L Kennametal is a registered trademark of Kennametal Inc. STFPR ORING ARS USING TPMT INSERTS K-1260R $39.00 K-1270R $49.00 K-1280R $50.00 K-1200R $39.00 K-1210R $45.00 K-1220R $50.00 K-1230R $58.00 Min ore L K-3260R $ K-3270R $ K-3280R $ Min ore L K-3230R $ (See inserts on following page) Carbide Carbide w/ Hole Insert TPMT21.5_ TPMT32.5_ Tungaloy Reference# 06-STFPR-2 08-STFPR-2 10-STFPR-2 12-STFPR-3 D.375 (3/8).500 (1/2).625 (5/8).750 (3/4) ZTEK SAFETY GLASSES Min ore L UD-C06MSTFPR2 $ UD-C08RSTFPR2 $ L Fig 1 Fig 2 Economical wrap-around single lens provides full panoramic view Soft, non-slip rubber temple tips provide non-binding fit Integrated nose piece Lenses are coated for superior scratch resistance Lenses provide 99% protection against harmful UV rays Meets or exceeds ANSI Z standards UD-E06MSTFPR2 $ UD-E08RSTFPR2 $ UD-E10QSTFPR2 $ UD-E12QSTFPR3 $ Frame Color K-5260R $ K-5270R $ K-5280R $ K-5200R $ K-5210R $ K-5220R $ K-5230R $ Screw SC-31 $1.00 SC-31 $1.00 SC-31 $1.00 SC-32 $1.00 Screw $1.00 SC-31 SC-32 Please See Page 581 For Our Complete Selection Of Safety Glasses! Lense Color Wrench $5.00 TX-207 TX-215 Wrench TX-207 $5.00 TX-207 $5.00 TX-207 $5.00 TX-215 $5.00 Clear Clear PYR-S2510S $2.99 Gray Gray PYR-S2520S $3.29 D

31 TPMT INSERTS SS CS S CI AL NF GT SA IN R M F LEGEND Material ars Using IC T R TPMT21.5_ (TPMT 1102 ) / /32 Chip reaker PS F to M TO-3046 $ / /32 ars Using IC T R TPMT32.5_ (TPMT 16T3 ) / / / /32 ars Using IC T R TPMT21.5_ (TPMT 1102 ) TPMT32.5_ (TPMT 16T3 ) Stainless Steel Carbon Steel Steel Cast Iron Aluminum Non-Ferrous Material General Turning Super Alloys Inconel Operation Roughing Medium Finishing / / / / / / / /32 TUNGALOY MITSUISHI INSERTS [] S, SS S, SS SS S,SS SS, CS S, CI AL, NF GT AT530 NS530 T6030 T9125 US-735 $10.95 UC-6010 $10.95 Oper. CERMET COATED CARIDE COATED CARIDE HTi20T $9.95 UNCOATED CARIDE - TO-8090 $5.22 TO-3670 $5.22 AP25N $9.95 CERMET MQ R M-421 M-422 M-423 M-424 SQ F M-431 M-432 M-433 PS F to M TO-3052 $4.80 TO-3053 $3.33 TO-8096 $5.22 TO-3671 $ MQ R M-441 M-442 M-443 M-444 SQ F M-451 M-452 M-453 PS F to M TO-3059 $5.22 Chip breaker - TO-8104 $5.22 TO-3672 $5.22 Oper. AT530 NS530 T6030 T US-735 $11.95 UC-6010 $11.95 HTi20T $10.95 AP25N $10.95 MQ R M-461 M-462 M-463 M-464 SQ F M-471 M-472 M-473 M-474 PS F to M TO-3066 $ TO-8146 $7.35 TO-3674 $ MQ R M-481 M-482 M-483 M-484 SQ F M-491 M-492 M-493 M-494 PS F to M TO-3073 $7.35 Chip breaker - TO-8153 $7.35 TUNGALOY TO-3675 $ ISCAR INSERTS [] S, SS S, SS S, SS S,SS CI S, SS, CI S, SS S AT530 NS530 T6030 T9125 IC20 IC656 IC8048 IC9025 Oper. CERMET COATED CARIDE - F PS F to M TO-3052 $4.80 TO-3053 $3.33 TO-8096 $5.22 TO-3671 $ F PS F to M TO-3059 $ TO-8104 $5.22 TO-3672 $ F PS F to M TO-3066 $ TO-8146 $7.35 TO-3674 $ F PS F to M TO-3073 $ uy In ox Quantities & Save! uy In ox Quantities & Save! TO-8153 $7.35 TO-3675 $7.63 UNCOATED CARIDE CAR-841 $6.95 COATED CARIDE CAR-842 $8.95 COATED CARIDE CAR-843 $8.95 COATED CARIDE CAR-844 $ CAR-851 $6.95 CAR-852 $8.95 CAR-853 $8.95 CAR-854 $ CAR-861 $7.95 CAR-862 $10.95 CAR-863 $10.95 CAR-864 $ CAR-871 $7.95 TPMT I.C.-size T-thickness R-radius CAR-872 $10.95 MITSUISHI CAR-873 $10.95 CAR-874 $ Master Catalog 299 CARIDE INSERTS DEURRING

32 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SCLCR ORING ARS USING CCMT/CCGT INSERTS SCLCR ORING ARS Industry standard SCLCR type Uses CCMT or CCGT type inserts Available in solid steel or coolant thru s have locating flats for easy set up Please see following page for inserts Uses Insert CC_T-21.5_ CC_T-32.5_ SCLCR ORING ARS Industry standard SCLCR type Uses CCMT or CCGT type inserts s have locating flats for easy set up Available in steel, heavy metal or carbide shanks Please see following page for inserts Made in the Insert CC 21.5_ CC 32.5_ Uses Insert CC_T-21.5_ CC_T-32.5_ Style Sandvik Reference # _05-SCLCR-2 _06-SCLCR-2 _08-SCLCR-2 _10-SCLCR-2 _08-SCLCR-3 _10-SCLCR-3 _12-SCLCR-3 D (5/16) (3/8) (1/2) (5/8) (1/2) (5/8) (3/4) Fig # Min ore Steel -4xD Heavy Metal-6xD Carbide -8xD Master Catalog L _16-SCLCR SCLCR/L ORING ARS Industry standard SCLCR/L type Steel shank Uses CCMT or CCGT inserts s have locating flats 3 side & end cutting edge angle Style Size d Size d Min ore D L Min ore D No. & S-1000R $39.00 S-1010R $41.00 S-1020R $45.00 S-1040R $50.00 S-1030R $45.00 S-1050R $50.00 S-1060R $58.00 S-1070R $85.00 L Right Hand Fig 1 Fig 2 F SOLID COOLANT THRU SPARE PARTS Min ore L No. & S-3000R $ S-3010R $ S-3020R $ S-3040R $ Min ore L Right Hand Left Hand S-3050R $ S-3060R $ S-3070R $ Left Hand SI-SCLCR/L I R I L $43.04 SI-SCLCR/L I R I L $43.04 SI-SCLCR/L I R I L $43.04 SI-SCLCR/L I R I L $57.46 SI-SCLCR/L I R I L $43.33 SI-SCLCR/L I R I L $50.51 SI-SCLCR/L I R I L $54.30 SI-SCLCR/L I R I L $69.03 SI-SCLCR S05K-SCLCR2-M $ A05K-SCLCR2-M $57.00 SI-SCLCR S06K-SCLCR2-M $ A06K-SCLCR2-M $61.75 SI-SCLCR S08K-SCLCR2-M $ A08K-SCLCR2-M $67.45 SI-SCLCR S10Q-SCLCR2-M $ A10Q-SCLCR2-M $82.65 SI-SCLCR S08K-SCLCR3-M $ A08K-SCLCR3-M $67.45 SI-SCLCR S10Q-SCLCR3-M $ A10Q-SCLCR3-M $82.65 SI-SCLCR S12Q-SCLCR3-M $ A12Q-SCLCR3-M $96.90 SI-SCLCR S16Q-SCLCR3-M $ A16Q-SCLCR3-M $ NEW ITEM! NEW ITEM! Using CCMT/CCGT Inserts Screw SC-76 $1.00 SC-77 $1.00 No. & S-5000R $ S-5010R $ S-5020R $ S-5040R $ S-5030R $ S-5050R $ S-5060R $ S-5070R $ Screw I $0.72 I T $0.72 Screw $1.00 SC-76 SC-76 SC-77 SC-77 SPARE PARTS Hex/Torx Key TX-207 $5.00 TX-215 $5.00 Hex/Torx Key I $4.99 I $4.99 F D Wrench $5.00 TX-207 TX-207 TX-215 TX-215

33 CCMT INSERTS 7 CCMT I.C.-size T-thickness R-radius LEGEND Material SS Stainless Steel CS Carbon Steel S Steel CI Cast Iron AL Aluminum NF Non-Ferrous Material Operation F Finish M Medium ars Using CCMT21.5_ (CCMT 0602 ) CCMT32.5_ (CCMT 09T3 ) IC T R / /8 ORING AR SLEEVES uy In ox Quantities & Save! / /32 chip breaker S,SS NF,SA SS,SA SS S SS AL AT530 AH110 AH120 T6030 T9125 SH730 KS05F oper. CERMET COATED CARIDE JS F / / / PS M to F TO-1133 $ TO-4917 $5.60 AL M to F TO-3500 $5.85 TO-4914 $5.85 JS PS M to F TO-1141 $5.60 PF M to F - PM M to F TO-3800 $5.60 TO-3805 $5.60 TO-4923 $5.60 TO-3803 $5.60 TO-3809 $5.60 TO-4919 $5.60 TO-4929 $5.60 TO-3814 $5.60 TO-3820 $5.60 TO-4925 $5.60 TO-3501 $5.85 TO-3804 $5.85 TO-3810 $5.85 TO-4920 $5.85 TO-3502 $5.85 TO-3815 $5.85 TO-3821 $5.85 TO-4926 $5.85 TO-4931 $6.03 TO-3503 $6.03 TO $8.40 TO $ TO-3806 $ M to F PS M to F TO-1149 $5.60 PF M to F - PM M to F - 24 M to F - - TO-3811 $5.60 TO-3816 $5.60 TO-3817 $ JS M to F / / /32 PS M to F TO-1157 $ TO-3457 $6.93 JS PS M to F TO-1163 $6.93 PF M to F - PM M to F - - TO-3823 $6.93 TO-3828 $ TO-3829 $ TO-4940 $6.93 TO-3826 $6.93 TO-3832 $6.93 TO-4936 $6.93 TO-3504 $6.03 TO-3827 $6.03 TO-3833 $6.03 TO-4937 $6.03 UNCOATED CARIDE Master Catalog TO $ TO $8.09 TO $ TO $10.75 TO $10.75 TO $ PS M to F TO-1171 $6.93 PF M to F - PM M to F TO-3834 $6.93 TO-3839 $ TO-3840 $6.93 TO-4946 $6.93 TO-3837 $6.93 TO-3843 $6.93 TO-3505 $6.03 TO-3838 $6.03 TO-3844 $ TO $9.17 TO $ TO $ oring bar sleeves are used to adapt all boring bar or shank type tools to any CNC turning machine or machining center for extensions or hard to reach areas. They are hardened, precision ground concentric and black oxided for long life. Innovative design on the 1-1/2 OD boring bar sleeves helps the tools stay cool longer by projecting the coolant directly on the cutting edge. Please See Pages For Our Complete Selection! CARIDE INSERTS DEURRING

34 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS SDUCR ORING ARS USING DCMT/DCGT INSERTS SANDVIK STYLE SDUCR ORING ARS Industry standard SDUCR type Uses DCMT type inserts s have locating flats for easy set-up Steel shank See following page for inserts Made in the Uses Insert Industry Reference SDUCR ORING ARS USING DCMT/DCGT INSERTS Solid Carbide With Coolant Hole D Min ore L SPARE PARTS Screw $1.00 Wrench $ SDUCR S-1100R $39.00 DC 21.5_ 08-SDUCR S-1110R $45.00 SC-76 TX SDUCR S-1120R $50.00 DC 32.5_ 12-SDUCR S-1130R $58.00 SC-77 TX-215 *Sandvik is a registered trademark of Sandvik Coromant SDUCR/L ORING ARS Industry standard SDUCR type Uses DCMT or DCGT inserts 3 end cutting edge angle s have locating flats for easy set-up Steel shank See following page for inserts Uses Insert DC_T-21.5_ DC_T-32.5_ Style Size d Min ore D L F Right Hand NEW ITEM! Left Hand SI-SDUCR/L06-2 3/ I R I L $42.26 SI-SDUCR/L08-2 1/ I R I L $44.40 SI-SDUCR/L10-2 5/ I R I L $47.50 SI-SDUCR/L12-3 3/ I R I L $49.64 SI-SDUCR/L I R I L $54.22 SI-SDUCR/L / I R I L $83.44 Screw I $0.72 I T $0.72 D SPARE PARTS Hex/Torx Key I $4.99 I $4.99 A ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Uses Insert DC 21.5_ Industry Reference D Min ore Master Catalog L Accessories Screw $1.00 Wrench $ SDUCR TO $ TO-CST25 TO-T-8F 08-SDUCR TO $ TO-CST25 TO-T-8F 10-SDUCR TO $ TO-CST25 TO-T-8F DC 32.5_ 12-SDUCR TO $ TO-CST4S TO-T-15F

35 DCMT/DCGT INSERTS DCMT I.C.-size T-thickness R-radius SS CS S CI AL NF GT SA IN R M F LEGEND Material Stainless Steel Carbon Steel Steel Cast Iron Aluminum Non-Ferrous General Turning Super Alloys Inconel Operation Roughing Medium Finishing ars Using DCMT21.5_ (DCMT 0702 ) DCMT32.5_ (DCMT 11T3 ) NEW GRADES! SH730-Ideal for stainless steels and high temp alloys KS05F-Ideal for Aluminum IC T R / / / /32 chip breaker S,SS NF,SA SS,SA SS S SS AL AT530 AH110 AH120 T6030 T9125 SH730 KS05F Oper. CERMET COATED CARIDE JS F / / /32 TO-1595 PS M to F $5.71 PF M to F TO-5529 $5.92 TO-3845 $5.92 AL F TO-1601 PS M to F $5.71 PF M to F - PM M to F TO $5.71 TO-3850 $5.71 TO-3851 $5.71 TO-5534 $5.71 TO-3848 $5.71 TO-3853 $5.71 TO-5530 $ M to F TO-1608 PS M to F $5.71 TO-3855 PF M to F - - $5.71 PM M to F - TO-3859 $5.71 TO-3860 $ M to F TO-3857 $5.71 TO-3862 $5.71 TO-5535 $5.71 TO-3566 $5.92 TO-3849 $5.92 TO-3854 $5.92 TO-5531 $5.92 TO-3567 $5.92 TO-3858 $5.92 TO-3863 $5.92 TO-5536 $ JS F / / /32 TO-1614 PS M to F $8.02 PF M to F M to F TO-3568 $8.33 TO-3864 $8.33 TO-5539 $8.33 JS TO-1620 TO-3569 PS M to F $8.02 $8.33 PF M to F - TO-3865 TO-3868 TO $8.02 $8.02 $8.33 PM M to F - TO-3870 TO-3871 TO-3874 TO-3875 $8.02 $8.02 $8.02 $ M to F TO-5545 TO-3731 $8.02 $8.33 UNCOATED CARIDE TO $9.52 TO $ TO $ TO $11.03 TO $ TO $11.03 TO $ AL TO $11.59 TO-1628 TO-3570 PS M to F $8.02 $ TO-3876 PF M to F - - $8.02 TO-3881 TO-3882 PM M to F - $8.02 $ M to F TO-3879 $8.02 TO-3885 $8.02 TO-5550 $8.02 TO-3880 $8.33 TO-3886 $8.33 TO-5551 $8.33 We Are A Full Line Supplier For Tungaloy! Carbide Inserts oring Turning Milling Drilling -Off Please Call For More Information! Master Catalog 303 CARIDE INSERTS DEURRING

36 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS STFCR/STUCR ORING ARS USING TCMT/TCGT INSERTS SANDVIK STYLE STFCR/STUCR ORING ARS Industry standard STFCR/STUCR type STUCR: 3 lead angle, STFCR: 0 Uses TCMT/TCGT type inserts s have locating flats for easy set-up Available in steel, heavy metal or carbide shanks See following page for inserts Made in the Insert TC_T 21.5_ TC_T 32.5_ TC_T 21.5_ TC_T 32.5_ Sandvik Reference _06-STFCR-2 _08-STFCR-2 _10-STFCR-2 _12-STFCR-2 _12-STFCR-3 _06-STUCR-2 _08-STUCR-2 _10-STUCR-2 _12-STUCR-3 D (3/8) (1/2) (5/8) (3/4) (3/4) (3/8) (1/2) (5/8) (3/4) Min ore Steel -4xD Heavy Metal-6xD Carbide -8xD L S-1200R $41.00 S-1210R $45.00 S-1220R $50.00 S-1230R $58.00 S-1240R $58.00 S-1250R $41.00 S-1260R $45.00 S-1270R $50.00 S-1290R $58.00 Sandvik is a registered trademark of Sandvik Coromant Company STUCR ORING ARS USING TCMT/TCGT INSERTS Industry standard STUCR/L type Steel shank Uses TCMT or TCGT inserts s have locating flats 3 end cutting edge angle Min ore L S-3200R $ S-3210R $ S-3220R $ S-3230R $ S-3240R $ S-3250R $ S-3260R $ S-3270R $ S-3290R $ NEW ITEM! Min ore L S-5200R $ S-5210R $ S-5220R $ S-5230R $ S-5240R $ S-5250R $ S-5260R $ S-5270R $ S-5290R $ D Screw $1.00 SC-76 SC-77 SC-76 SC-77 Wrench $5.00 TX-207 TX-215 TX-207 TX-215 ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Uses Insert TC_T-21.5_ TC_T-32.5_ Style Size d Min ore D Master Catalog L F Right Hand Left Hand SI-STUCR06-2 3/ I R I L $42.98 SI-STUCR08-2 1/ I R I L $48.10 SI-STUCR10-2 5/ I R I L $48.78 SI-STUCR12-3 3/ I R I L $51.51 SI-STUCR I R I L $55.58 SI-STUCR / I R I L $63.30 SI-STUCR / I R I L $78.96 Screw I $0.72 I T $0.72 SPARE PARTS Hex/Torx Key I $4.99 I $4.99

37 TCMT/TCGT INSERTS SS CS S CI AL NF GT SA IN R M F LEGEND Material Stainless Steel Carbon Steel Steel Cast Iron Aluminum Non-Ferrous General Turning Super Alloys Inconel Operation Roughing Medium Finishing 7 ars Using TCMT 21.5_ (TCMT 1102 ) TCMT 32.5_ IC T R / / / / / / / / /32 TUNGALOY INSERT GRADE INFORMATION TCMT I.C.-size T-thickness R-radius Chip breaker PS/JS M to F TO-2547 $5.22 S,SS S,SS S,SS NF SS AL AT530 NS530 T6030 T9125 SH730 KS05F Oper. CERMET COATED CARIDE 24 M to F - - TO-2545 $3.75 TO-7216 $ TO-3630 $5.22 TO-7212 $5.22 JS/AL F PS M to F TO-2554 $5.22 TO-2555 $3.75 TO-7223 $5.22 PM M to F M to F - PS M to F TO-2562 $5.22 TO-2552 $3.75 TO-7218 $ PM M to F M to F - PS/AL M to F TO-2569 $7.35 TO-2560 $3.75 TO-2570 $5.29 TO-7225 $5.22 TO-7235 $10.00 PM M to F M to F - PS/AL M to F TO-2577 $7.63 TO-2567 $5.29 TO-2578 $5.29 TO-7230 $10.00 TO-7242 $10.00 PM M to F M to F - TO-2575 $5.29 TO-7237 $7.63 TO-3631 $5.22 TO-7221 $5.22 TO-7219 $5.22 TO-3632 $5.22 TO-7228 $5.22 TO-7226 $5.22 TO-3633 $7.63 TO-7233 $7.63 TO-7231 $7.63 TO-3634 $7.63 TO-7240 $7.63 TO-7238 $7.63 TO $7.21 UNCOATED CARIDE TO $ TO $7.21 TO $ TO $ TO $ Grade Features Applications - High Wear resistance and thermal and shock resistance - General purpose cermet covering a wide range of cutting conditions from low to high NS530 - Performs well in wet cutting speeds for various steels. AT530 -Special PVD TiAlN coated cermet. -Well balanced wear resistance and toughness. NEW GRADES! SH730-Ideal for stainless steels and high temp alloys KS05F-Ideal for Aluminum -Finish to semi-finish turning and boring of various steels and stainless steels. -Can be used for light interrupted cutting. SH730 T TiAlOxide coating - wear resistant substrate plus multiple coated layers - Low to medium speed turning and boring of steels and stainless steels -Typical K10 (C-2) type uncoated carbide with good overall wear KS05F resistance and toughness. Used for positive inserts. - For general boring of non-ferrous materials. Ideal for aluminum. CARIDE INSERTS HEX WRENCH SETS Type Full Line Available! Please call for more information. No. Of Pieces Inch 12 Inch 13 Hex Wrench Set Includes.050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1 / 4, 5/16.050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1 / 4, 5/16, 3/8 O $7.20 O $8.20 Metric 9 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm O $7.76 Combo Pack 13 & 9 Inch & Metric Set O $ Master Catalog 305 DEURRING

38 CHUCK JAWS LATHE WORKHOLDING SUMITOMO STYLE ORING ARS USING TRIANGLE INSERTS Uses TGP/TPGP/TPGG triangle type inserts s have locating flats for easy set-up Available in steel, heavy metal or carbide shanks See bottom of page for inserts D NEW ITEM! MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS USST ORING ARS Steel -4xD Heavy Metal-6xD Carbide -8xD Insert Industry Reference D Min ore TGP-52 _STJOR TPGP-63 _STJOR TPGG-22 _STJOR TPGG-22 _STJOR TPGG-22 _STJOR TPGG-33 _STJOR TPGG-33 _STJOR INSERTS TURN-TEK STEEL ORING ARS Uses Insert SUMITOMO Industry Reference SUMITOMO INSERT GRADES Size d Min ore D L ars Using L T-1000 $39.00 T-1005 $39.00 T-1010 $41.00 T-1015 $41.00 T-1020 $50.00 T-1025 $58.00 T-1030 $85.00 I.C. T R TGP-52 5/32 1/16 TPGP-63 3/16 3/32 TPGG-22 1/4 1/8 TPGG-33 3/8 3/16 Min ore L Sumitomo Reference 1/128 TGT-520.5L 1/64 TGT-521L 1/128 TPGP-630.5L 1/64 TPGP-631L 1/128 TPGG-220.5L 1/64 1/32 TPGG-221L T-3000 $ T-3005 $ T-3010 $ T-3015 $ T-3020 $ T-3025 $ T-3030 $ Min ore Grade T12A/T220A SU-621 $7.55 SU-622 $7.55 SU-623 $8.62 SU-624 $8.62 SU-625 $9.09 SU-626 $9.09 L Grade G10E SU-641 $7.93 T-5000 $ T-5005 $ T-5010 $ T-5015 $ T-5020 $ T-5025 $ T-5030 $ Grade AC10/AC2000 Screw $1.00 SC-88 SC-89 SC-83 SC-84 SC-85 Grade AC SU-643 $ SU-645 $9.54 SU-646 $9.54 TPMN-221ENF - - TPGG-222L SU-627 $9.09 SU-647 $9.54 TPMT-222ENF - - 1/128 TPGG-330.5L 1/64 1/32 Right Hand TPGG-331L SU-628 $12.51 SU-629 $ SU-636 $7.10 SU-656 $ SU-637 $7.79 SU-657 $ SU-649 $12.51 TPMT-331ENF - - TPGG-332L TPGP-63 SI-STJOR-066 3/ S06K-STJOR6-M $45.00 TPGG-22 SI-STJOR-082 1/ S08K-STJOR2-M $52.00 TPGG-22 SI-STJOR-102 5/ S10K-STJOR2-M $64.00 SU-630 $12.51 SU-650 $13.53 TPMT-332ENF - - SPARE PARTS Screw SC-89 $1.00 Hex/Torx Key TX-207 $ SU-639 $9.58 SU-659 $ SU-640 $9.58 F D SU-660 $9.58 MRO & SAFETY FLAT STOCK/DRILL ROD Grade T12A, T220A G10E AC10, AC2000 AC-3000 Insert Type Cermet Uncoated Carbide Coated Carbide Coated Carbide Material Steels, Stainless Steel Cast Iron, Non-ferrous Steels, Stainless Steel Soft Steels, Stainless Steel Cutting Conditions Finishing Finish to Medium Gen. Purp. to Roughing Roughing to Semi-Finishing Master Catalog

39 SUMITOMO STYLE ORING ARS USING DIAMOND INSERTS Uses CPGP/CPGM diamond type inserts s have locating flats for easy set-up Available in steel, heavy metal or carbide shanks See bottom of page for inserts Made in the Insert Sumitomo Reference D Min ore CPGP-03 _SCLOR CPGP-03 _SCLOR CPGM-32 _SCLOR CPGM-32 _SCLOR CPGM-43 _SCLOR Steel -4xD Heavy Metal-6xD Carbide -8xD L T-1035 $41.00 T-1040 $41.00 T-1045 $50.00 T-1050 $58.00 T-1055 $85.00 Min ore L T-3035 $ T-3040 $ T-3045 $ T-3050 $ T-3055 $ Min ore L T-5035 $ T-5040 $ T-5045 $ T-5050 $ T-5055 $ D Screw $1.00 SC-83 SC-86 SC-87 INSERTS SUMITOMO INSERT GRADES LATHE TOOLHOLDER USHINGS FEATURES: Increased step diameter for easy and perfect sealing. Concentric ground and diamond polished OD & ID resulting in a mirror smooth finish Easy Entry feature on OD for quick insertion Wrench flats for easy removal Step relief for easy removal and gripping on Z style bushings Type and size clearly marked on surface of head diameter for easy identification 100% Satisfaction Guaranteed ars Using CPGT CPGM CPGT-43 CPGT1204 I.C. T R 5/16 3/32 3/8 1/8 1/2 3/16 Industry Reference No. GradeT12A T220A 1/128 CPGP-030 SU-661 1/64 CPGP-031 SU-662 1/32 CPGP-032 SU-663 1/128 CPGM-320 SU-664 1/64 CPGM-321 SU-665 1/32 CPGM-322 SU-666 1/128 CPGM-430 SU-667 1/64 CPGM-431 SU-668 1/32 CPGM-432 SU-669 $13.46 $17.73 Grade T12A, T220A G10E AC10, AC3000 AC-25 Insert Type Cermet Uncoated Carbide Coated Carbide Coated Carbide Material Cutting Conditions Steels, Stainless Steel Finishing Cast Iron, Non-ferrous Finish to Medium Steels, Stainless Steel Gen. Purpose to Roughing Please See Pages For More Information! SUMITOMO Soft Steels, Stainless Steel Roughing to Semi-Finishing SPECIFICATIONS: Material: ALLOY STEEL 8620 Hardness Data: Rc for longer tool life Case Hardened and Ground Concentric OD & ID Axial Concentricity: OD & ID Tolerance: H6 & g6 in grinding the OD & ID Master Catalog 307 CARIDE INSERTS DEURRING

40 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SVUCR/L, SWUCR/L & CTFPR ORING ARS SVUCR/L ORING ARS Industry standard SVUCR/L type Steel shank Uses VCMT or VCGT inserts s have locating flats 3 end cutting edge angle Uses Insert VC_T-22_ VC_T-33_ Style SWUCR/L ORING ARS Industry standard SWUCR/L type Steel shank Uses WCMT or WCGT inserts s have locating flats 3 end cutting edge angle Uses Insert WC_T 32.5_ Inserts Size d Min ore D Master Catalog L F Right Hand Left Hand Screw SI-SVUCR/L12-2 3/ I R I L $68.68 I SI-SVUCR/L I R I L $70.70 $0.72 SI-SVUCR/L I R I L $66.54 I SI-SVUCR/L / I R I L $79.16 $6.60 Style CTFPR ORING ARS Industry standard CTFPR type Steel shank Uses TPU inserts s have locating flats 3 end cutting edge angle For oring ar Size d Min ore D Style SI-CTFPR Shim L Inserts Size d Min ore D L C E SPARE PARTS Right Hand Hex/Torx Key I $4.99 I $4.99 TPU-21_ 5/ I $64.21 TPU-32_ 3/ I $67.62 TPU-32_ I $73.94 TPU-32_ 1-1/ I $95.94 TPU-32_ 1-1/ I $ TPU-43_ I $ F Shim Screw Right Hand Left Hand Lock Screw Hex Key SPARE PARTS TPU-21_ I I $4.80 I $1.00 TPU-32_ I I $5.27 I $1.00 TPU-32_ I I $5.27 I $1.00 TPU-32_ I I $28.98 I $2.00 I $5.27 I $1.00 TPU-32_ I I $3.49 I $2.00 I $11.31 I $1.00 TPU-43_ I I $3.49 I $2.00 I $11.31 I $1.00 SI-SWUCR/L08-3 1/ I R I L $50.91 SI-SWUCR/L10-3 5/ I R I L $54.28 SI-SWUCR/L12-3 3/ I R I L $59.09 NEW ITEM! REPLACEMENT PARTS FOR CTFPR ORING ARS NEW ITEM! NEW ITEM! Screw I T $0.72 Hex/Torx Key I $4.99

41 COOLANT THRU ORING ARS COOLANT-THRU ORING ARS FEATURES: Durable and unique chrome nickel toolholder Positive chip control Coolant-thru hole design holder includes torx screw and torx key 90 oring & Facing/95 Approach For lind Holes Using 90 Insert Face Profile oring & Facing Uses CCMT Inserts (not included) Toolholder Nomenclature F Over Insert Min. ore Right Hand Left Hand A04F SCLCR 2 1/ MI MI $65.30 A05H SCLCR 2 5/ MI MI $67.05 A06J SCLCR 2 3/8 4 1/ MI MI $69.95 A08K SCLCR 2 1/ MI MI $72.90 A10M SCLCR 2 5/ MI MI $77.90 Uses TCMT Inserts (not included) Toolholder Nomenclature F Over Insert Min. ore Right Hand Left Hand A06J STFCR 2 3/8 4 1/ MI MI $68.25 A08K STFCR 2 1/ MI MI $72.25 A10M STFCR 2 5/ MI MI $73.20 Uses DCMT Inserts (not included) Toolholder Nomenclature F Over Insert Min. ore K Angle Right Hand Left Hand A05H SDQCR 2 5/ MI MI $98.00 A06J SDUCR 2 3/8 4 1/ MI MI $72.80 A08K SDUCR 2 1/ MI MI $71.73 A10M SDUCR 2 5/ MI MI $72.68 CARIDE INSERTS COOLANT-THRU ORING AR SETS All sets come complete with carbide insert, torx screw and torx key. meters Description Set 1/4, 5/16, 3/8, 1/2 Set of 4 pcs. SCLCR with CCMT insert MI $ /8, 1/2, 5/8 Set of 3 pcs. SDUCR with DCMT insert MI $ /8, 1/2, 5/8 Set of 3 pcs. STFCR with TCMT 2151 insert MI $ MULTI-PURPOSE SETS 4 Piece Multi-Purpose Set 7 Piece Multi-Purpose Set Description 4 Piece Multi-Purpose Set 1 ea. SDJCR, SDJCL, SDNCN, SDQCR Description 7 Piece Multi-Purpose Set 1 ea. SCLCR, SCLCL, SCCR, SCKCR, SCMCN, SCSCR, SCLCR Sizes Square 3 PCS. Round 1 PC. Set 5/16 5/16 MI $ /8 3/8 MI $ /2 1/2 MI $ /8 5/8 MI $ Square 6 PCS. Round 1 PC. Set 1/4 1/4 MI $ /16 1/4 MI $ /8 5/16 MI $ /2 3/8 MI $ /8 1/2 MI $ Master Catalog 309 DEURRING

42 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ORING ARS-MCLNR/L, SI-MDUNR/L, SI-MTFNR/L SI-MCLNR/L ORING ARS -5 Side & End Cutting Solid Steel Negative Rake Using CNMG, CNMA & CNM_ type inserts CNMG Inserts on Pages Industry Reference Uses Insert -3 Side Cutting Solid Steel Negative Rake Using DNMG, DNMA & DNG_ type inserts Min ore SI-MTFNR/L ORING ARS 0 Side Cutting Offset Negative Rake Using TNMG, TNMP, TNG_ & TNM_ type inserts C SI-MDUNR/L ORING ARS D R Right Hand Left Hand SI-MCLNR/L-164 CNMG TH-1805 TH-2805 $ SI-MCLNR/L-204 CNMG /4 14 TH-1810 TH-2810 $ SI-MCLNR/L-244 CNMG /2 14 TH-1815 TH-2815 $ SI-MCLNR/L-284 CNMG /4 12 TH-1820 TH-2820 $ SI-MCLNR/L-325 CNMG TH-1825 TH-2825 $ DNMG Inserts on Pages 327 Industry Reference Uses Insert Min ore C D R Right Hand Left Hand SI-MDUNR/L-204 DNMG /4 10 TH-1830 TH-2830 $ SI-MDUNR/L-244 DNMG /2 10 TH-1835 TH-2835 $ SI-MDUNR/L-324 DNMG TH-1840 TH-2840 $ Seat ICSN -432 $2.76 ICSN 533 $3.38 Seat IDSN-433 $2.50 EXTRA HARDWARE Lock Pin NL-44 $1.90 NL-46 $1.90 NL-58 $1.90 Clamp CL-20 $2.98 CL-12 $2.98 EXTRA HARDWARE Lock Pin NL-46 $1.90 Clamp CL-20 $2.98 EXTRA HARDWARE Clamp Screw XNS-47 $0.74 XNS-510 $0.74 Clamp Screw XNS-59 $0.74 ENDMILLS, DRILLS TAPS & REAMERS TNMG Inserts on Pages 328 Industry Reference Uses Insert Min ore C D R Right Hand Left Hand SI-MTFNR/L-163 TNMG TH-1925 TH-2925 $ SI-MTFNR/L-203 TNMG /4 12 TH-1930 TH-2930 $ SI-MTFNR/L-244 TNMG /2 10 TH-1935 TH-2935 $ SI-MVUNR/L ORING ARS Seat - ITSN-433 $3.10 Lock Pin NL-33L $1.90 NL-46 $1.90 Clamp CL-7 $2.98 CL-9 $2.98 Clamp Screw XNS-35 $0.74 XNS-59 $0.74 ARASIVES MEASURING TOOLS -3 Side Cutting Steel Negative Rake Using VNGA, VNMA, VNMG & VNM_ type inserts VNMG Inserts on Page 329 EXTRA HARDWARE MRO & SAFETY FLAT STOCK/DRILL ROD Industry Reference Uses Insert Min ore C D Master Catalog R Right Hand Left Hand SI-MVUNR-203 VNMG /4 12 TH-1860 TH-2860 $ IVSN-324 SI-MVUNR-243 VNMG /2 12 TH-1865 TH-2865 $ $2.24 Seat Lock Pin NL-34L $1.90 Clamp CL-30 $5.28 Clamp Screw XNS-510 $0.74

43 IG ORING ARS-SMWLNR/L,MTUNR/L SI-MWLNR/L ORING ARS -5 Side & End Cutting Offset Negative Rake Using WNGG, WNMA, WNMG type inserts WNMG Inserts on Pages 330 Industry Reference Industry Reference Uses Insert -3 End Cutting, Solid Steel ar Negative Rake Using TNMG, TNMA, TNG_ & TNM_ type inserts Uses Insert Min ore Min ore C SI-MTUNR/L ORING ARS C D D R Right Hand Left Hand S12S-MTUNR/L-3 TNMG /4 14 TH-1895 TH-2895 $ S16T-MTUNR/L-3 TNMG TH-1900 TH-2900 $ R Right Hand Left Hand Seat ITSN-322 $1.90 S20U-MTUNR/L-4 TNMG /4 14 TH-1905 TH-2905 $ ITSN-432 S24U-MTUNR/L-4 TNMG /2 11 TH-1910 TH-2910 $ $3.10 EXTRA HARDWARE SI-MWLNR/L-123 WNMG /4 14 TH-1870 TH-2870 $ NL-33L SI-MWLNR/L-163 WNMG TH-1875 TH-2875 $ $1.90 SI-MWLNR/L-203 WNMG /4 14 TH-1880 TH-2880 $ SI-MWLNR/L-164 WNMG TH-1885 TH-2885 $ SI-MWLNR/L-204 WNMG /4 14 TH-1890 TH-2890 $ TNMG Inserts on Pages 328 Seat IWSN-323 $2.52 IWSN-433 $3.40 Lock Pin NL-34L $1.90 EXTRA HARDWARE Lock Pin Clamp NL-33 $1.90 CL-7 NL-34L $2.98 $1.90 NL-46 $1.90 Clamp CL-6 $2.98 CL-6 $2.98 NL-44 $1.90 CL-20 NL-46 $2.98 $1.90 CL-9 $2.98 Clamp Screw XNS-36 $0.74 XNS-36 $0.74 XNS-47 $0.74 Clamp Screw XNS-35 $0.74 XNS-59 $0.74 INDEXALE DRILLS CARIDE INSERTS Please See Pages For More Information! DEURRING Coolant Thru Indexable Drills Crafted From H13 For Superior Toughness & Strength! Master Catalog 311

44 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING COOLANT THRU ORING ARS & OD TOOLHOLDERS COOLANT THRU ORING ARS Jet-Stream FEATURES: Air or liquid coolant, chip flush system Precise insert repeatability Extends insert life, cuts machining cost 1000 PSI coolant pressure 1/8 NPT Gage Insert C D F K Right Hand Left Hand Seat $74.50/10pk Seat Screw Locking Clamp A-Air $20.00ea Locking Clamp L-Liquid $20.00ea AS-ADCLN R/L COOLANT THRU ORING ARS-Style L - Negative 5 End Or Side Cutting Edge Angle for CNM_ (80 mond) inserts CNMG 33_ DN-AS12RADCLNR3 DN-AS12RADCLNL3 $ DN-JSLC-AC3 DN-JSLC-LC3 CNMG 43_ DN-AS16RADCLNR4 DN-AS16RADCLNL4 $ DN-S8012P DN-SM-M4 DN-JSLC-AC4 DN-JSLC-LC4 CNMG 43_ DN-AS20SADCLNR4 DN-AS20SADCLNL4 $ DN-S8012P DN-SM-M4 DN-JSLC-AC4 DN-JSLC-LC4 CNMG 43_ DN-AS24SADCLNR4 DN-AS24SADCLNL4 $ DN-S8012P DN-SM-M4 DN-JSLC-AC4 DN-JSLC-LC4 CNMG 43_ DN-AS32TADCLNR4 DN-AS32TADCLNL4 $ DN-S8012P DN-SM-M4 DN-JSLC-AC4 DN-JSLC-LC4 CNMG 54_ DN-AS32TADCLNR5 DN-AS32TADCLNL5 $ DN-S8016P DN-SM-M5 DN-JSLC-AC5 DN-JSLC-LC5 AS-ADVUN R/L COOLANT THRU ORING ARS-Style U - Negative 3 side cutting edge angle for VNM_ (35 mond) inserts VNMG 33_ DN-AS16RADVUNR3 DN-AS16RADVUNL3 $ DN-S3516P DN-SM-M3 DN-JSLC-AV3 DN-JSLC-LV3 VNMG 33_ DN-AS20RADVUNR3 DN-AS20RADVUNL3 $ DN-S3516P DN-SM-M3 DN-JSLC-AV3 DN-JSLC-LV3 VNMG 33_ DN-AS24SADVUNR3 DN-AS24SADVUNL3 $ DN-S3516P DN-SM-M3 DN-JSLC-AV3 DN-JSLC-LV3 AS-ADWLN R/L COOLANT THRU ORING ARS-Style L - Negative 5 end and side cutting edge angle for WNM_ (80 Trigon) Inserts WNMG 33_ DN-AS12RADWLNR3 DN-AS16RADWLNL3 $ DN-JSLC-AW3 DN-JSLC-LW3 WNMG 43_ DN-AS16RADWLNR4 DN-AS16RADWLNL4 $ DN-S8008P DN-SM-M4 DN-JSLC-AW4 DN-JSLC-LW4 WNMG 43_ DN-AS20SADWLNR4 DN-AS20SADWLNL4 $ DN-S8008P DN-SM-M4 DN-JSLC-AW4 DN-JSLC-LW4 WNMG 43_ DN-AS24SADWLNR4 DN-AS24SADWLNL4 $ DN-S8008P DN-SM-M4 DN-JSLC-AW4 DN-JSLC-LW4 WNMG 43_ DN-AS32TADWLNR4 DN-AS32TADWLNL4 $ DN-S8008P DN-SM-M4 DN-JSLC-AW4 DN-JSLC-LW4 COOLANT THRU OD TOOLHOLDERS Jet-Stream FEATURES: Air or liquid coolant, chip flush system Precise insert repeatability Extends insert life, cuts machining cost 1000 PSI coolant pressure 1/8 NPT PVD-TiN Coated, 92Rc Surface Hardening, Wear Resistant! gram of ADCLN oring ar gram of ADCLN Toolholder ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Gage Insert A C E F Right Hand Left Hand Seat $74.50/10pk Master Catalog Seat Screw Locking Clamp A-Air $20.00ea Locking Clamp L-Liquid $20.00ea ADCLN R/L COOLANT THRU TOOLHOLDERS-Style L - Negative 5 End or Side Cutting Edge angle for CNM_ (80 mond) inserts CNMG 43_ DN-ADCLNR124 DN-ADCLNL124 $ DN-S8012P DN-SM-M4 DN-JSLC-AC4 DN-JSLC-LC4 CNMG 43_ DN-ADCLNR164D DN-ADCLNL164D $ DN-S8012P DN-SM-M4 DN-JSLC-AC4 DN-JSLC-LC4 CNMG 43_ DN-ADCLNR204D DN-ADCLNL204D $ DN-S8012P DN-SM-M4 DN-JSLC-AC4 DN-JSLC-LC4 CNMG 54_ DN-ADCLNR205D DN-ADCLNL205D $ DN-S8016P DN-SM-M5 DN-JSLC-AC5 DN-JSLC-LC5 ADDJN R/L COOLANT THRU TOOLHOLDERS- Style J - 3 Side Cutting Edge Angle For DNM_ (55 mond) inserts DNMG 33_ DN-ADDJNR123 DN-ADDJNL123 $ DN-S5511P DN-SM-M3 DN-JSLC-AD3 DN- JSLC-LD3 DNMG 43_ DN-ADDJNR124 DN-ADDJNL124 $ DN-S5515P DN-SM-M4 DN-JSLC-AD4 DN-JSLC-LD4 DNMG 43_ DN-ADDJNR164D DN-ADDJNL164D $ DN-S5515P DN-SM-M4 DN-JSLC-AD4 DN-JSLC-LD4 DNMG 43_ DN-ADDJNR204D DN-ADDJNL204D $ DN-S5515P DN-SM-M4 DN-JSLC-AD4 DN-JSLC-LD4 ADWLN R/L COOLANT THRU TOOLHOLDERS Style L - Negative 5 End And Side Cutting Edge Angle for WNM_ (80 TRIGON) inserts WNMG 43_ DN-ADWLNR124 DN-ADWLNL124 $ DN-S8008P DN-SM-M4 DN-JSLC-AW4 DN-JSLC-LW4 WNMG 43_ DN-ADWLNR164D DN-ADWLNL164D $ DN-S8008P DN-SM-M4 DN-JSLC-AW4 DN-JSLC-LW4 WNMG 43_ DN-ADWLNR204D DN-ADWLNL204D $ DN-S8008P DN-SM-M4 DN-JSLC-AW4 DN-JSLC-LW4 WNMG 43_ DN-ADWLNR244E DN-ADWLNL244E $ DN-S8008P DN-SM-M4 DN-JSLC-AW4 DN-JSLC-LW4 ADDITIONAL HARDWARE Seat Screws O-Rings (Pack Of 10) Coolant Quick Connect Kit # Ea # Ea # Ea DN-SM-M3 $1.45 DN-JSOR-03 $14.30 DN-JSQCK $22.26 DN-SM-M4 $1.45 DN-JSOR-04 $14.30 DN-JSQCK $15.12 DN-SM-M5 $1.72 DN-JSOR-05 $14.30 DN-JSQCK $16.62

45 ACKFACING ARS USING DCMT INSERTS ACKSPOTFACING ARS Available With Coolant Hole Carbide & Steel s Min. ores from.600 to Right and left handed available Coolant Thru Made in Min ore Min ore D D C C F F Material Material Coolant Thru Coolant Thru Insert Used Insert Used Right Handed ar Right Handed ar C Left Handed ar Left Handed ar Carbide No DCMT UD-C06M-SDUCR2 UD-C06M-SDUCL2 $ MTS 255 TX Carbide Yes DCMT UD-C08R-SDUCR2 UD-C08R-SDUCL2 $ MTS 255 TX Carbide Yes DCMT UD-E06M-SDUCR2 UD-E06M-SDUCL2 $ MTS 255 TX Carbide Yes DCMT UD-E08R-SDUCR2 UD-E08R-SDUCL2 $ MTS 255 TX Carbide Yes DCMT UD-E10Q-SDUCR2 UD-E10Q-SDUCL2 $ MTS 255 TX Carbide Yes DCMT UD-E10S-SDUCR2 UD-E10S-SDUCL2 $ MTS 255 TX Carbide Yes DCMT UD-E12Q-SDUCR3 UD-E12Q-SDUCL3 $ MTS 35 TX Carbide Yes DCMT UD-E12S-SDUCR3 UD-E12S-SDUCL3 $ MTS 35 TX Carbide Yes DCMT UD-E16R-SDUCR3 UD-E16R-SDUCL3 $ MTS 35 TX Carbide Yes DCMT UD-E16T-SDUCR3 UD-E16T-SDUCL3 $ MTS 35 TX Steel No DCMT UD-S06K-SDUCR2 UD-S06K-SDUCL2 $60.00 MTS 255 TX Steel No DCMT UD-S08M-SDUCR2 UD-S08M-SDUCL2 $64.00 MTS 255 TX Steel No DCMT UD-S10Q-SDUCR2 UD-S10Q-SDUCL2 $81.00 MTS 255 TX Steel No DCMT UD-S12Q-SDUCR3 UD-S12Q-SDUCL3 $93.00 MTS 35 TX Steel No DCMT UD-S16R-SDUCR3 UD-S16R-SDUCL3 $ MTS 35 TX Steel Yes DCMT UD-A06K-SDUCR2 UD-A06K-SDUCL2 $72.00 MTS 255 TX Steel Yes DCMT UD-A08M-SDUCR2 UD-A08M-SDUCL2 $75.00 MTS 255 TX Steel Yes DCMT UD-A10Q-SDUCR2 UD-A10Q-SDUCL2 $93.00 MTS Steel Yes DCMT UD-A12Q-SDUCR3 UD-A12Q-SDUCL3 $ MTS 35 TX Steel Yes DCMT UD-A16R-SDUCR3 UD-A16R-SDUCL3 $ MTS 35 TX Master Catalog 313 D Screw Screw Wrench Carbide No DCMT 21.5_ UD-C06M-SDXCR2 UD-C06M-SDXCL2 $ MTS 255 TX Carbide Yes DCMT 21.5_ UD-E06M-SDXCR2 UD-E06M-SDXCL2 $ MTS 255 TX Steel No DCMT 21.5_ UD-S06J-SDXCR2 UD-S06J-SDXCL2 $66.00 MTS 255 TX Steel Yes DCMT 21.5_ UD-A06J-SDXCR2 UD-A06J-SDXCL2 $79.00 MTS 255 TX Carbide No DCMT 21.5_ UD-C08R-SDXCR2 UD-C08R-SDXCL2 $ MTS 255 TX Carbide Yes DCMT 21.5_ UD-E08R-SDXCR2 UD-E08R-SDXCL2 $ MTS 255 TX Steel No DCMT 21.5_ UD-S08M-SDXCR2 UD-S08M-SDXCL2 $70.00 MTS 255 TX Steel Yes DCMT 21.5_ UD-A08M-SDXCR2 UD-A08M-SDXCL2 $83.00 MTS 255 TX Carbide Yes DCMT 21.5_ UD-E10Q-SDXCR2 UD-E10Q-SDXCL2 $ MTS 255 TX Carbide Yes DCMT 21.5_ UD-E10S-SDXCR2 UD-E10S-SDXCL2 $ MTS 255 TX Steel No DCMT 21.5_ UD-S10M-SDXCR2 UD-S10M-SDXCL2 $90.00 MTS 255 TX Steel Yes DCMT 21.5_ UD-A10M-SDXCR2 UD-A10M-SDXCL2 $ MTS 255 TX Carbide Yes DCMT 32.5_ UD-E12Q-SDXCR3 UD-E12Q-SDXCL3 $ MTS 35 TX Carbide Yes DCMT 32.5_ UD-E12S-SDXCR3 UD-E12S-SDXCL3 $ MTS 35 TX Steel No DCMT 32.5_ UD-S12Q-SDXCR3 UD-S12Q-SDXCL3 $ MTS 35 TX Steel Yes DCMT 32.5_ UD-A12Q-SDXCR3 UD-A12Q-SDXCL3 $ MTS 35 TX Carbide Yes DCMT 32.5_ UD-E16X-SDXCR3 UD-E16X-SDXCL3 $ MTS 35 TX Carbide Yes DCMT 32.5_ UD-E16Z-SDXCR3 UD-E16Z-SDXCL3 $ MTS 35 TX Steel No DCMT 32.5_ UD-S16X-SDXCR3 UD-S16X-SDXCL3 $ MTS 35 TX Steel Yes DCMT 32.5_ UD-A16X-SDXCR3 UD-A16X-SDXCL3 $ MTS 35 TX-215 PROFILING ARS Available With Coolant Hole Carbide & Steel s Min. ores from.600 to Right and left handed available Coolant Thru Made in C Wrench CARIDE INSERTS DEURRING

46 CHUCK JAWS LATHE WORKHOLDING OD TURNING HOLDERS-MCLNR/L, ACLNR/L OD TURNING TOOLHOLDER INDEX MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD MCLNR/L -5 Side & End Cutting Offset Negative Rake Using CNMG, CNMA, CNG_ & CNM_ type inserts Right Hand Model TO-ACLNR12-3 $75.00 TO-ACLNR16-3 $85.00 TO-ACLNR12-4 $75.00 TO-ACLNR16-4A $85.00 Industry Reference A-Type Toolholders ACLNR/L CNMG Inserts on Pages One action double clamping Strong and positive clamping power Fewer parts High accuracy A C Right Hand Model Left Hand Model Inserts Seat MCLNR/L-124 3/4 SQ 5 TH-1105 TH-2105 $41.05 CNMG-43 MCLNR/L-164C 1 SQ 5 TH-1110-CA TH-2110 $46.14 CNMG-43 MCLNR/L-164D 1 SQ 6 TH-1115 TH-2115 $43.68 CNMG-43 MCLNR/L-204D 1-1/4 SQ 6 TH-1120 TH-2120 $47.97 CNMG-43 MCLNR/L-854D 1 X 1-1/4 6 TH-1125 TH-2125 $47.97 CNMG-43 CNMG Inserts on Pages Left Hand Model TO-ACLNL12-3 $75.00 TO-ACLNL16-3 $85.00 TO-ACLNL12-4 $75.00 TO-ACLNL16-4 $85.00 b h h1 l1 f Increase Insert Life! Applicable Insert CN 32 _ CN 32 _ CN 43 _ CN 43 _ Shim or Seat TO-ELSC32 $6.39 TO-ELSC32 $6.39 TO-LSC42 $5.42 TO-LSC42 $ Master Catalog OD Toolholder Index Holder Type Page # MCLNR/L 314 MCRNR/L 315 MDPNN 315 MSDNN 315 MDJNR/L 316 MTANR/L 316 MTENNS 317 MTFNR/L 317 MTGNR/L 317 Spring Pin TO-LSP3 $0.68 TO-LSP3 $0.68 TO-LSP4 $0.68 TO-LSP4 $0.68 EXTRA HARDWARE ICSN-433 $2.76 ICSN-433 $2.76 ICSN-433 $2.76 ICSN-433 $2.76 ICSN-433 $2.76 Spring TO-P-7 $0.86 TO-P-7 $0.86 TO-P-9 $0.86 TO-P-9 $0.86 Lock Pin NL-46 $1.90 NL-46 $1.90 NL-46 $1.90 NL-46 $1.90 NL-46 $1.90 Clamp TO-ACP3 $5.20 TO-ACP3 $5.20 TO-ACP4 $5.20 TO-ACP4 $5.20 Holder Type Page # MTJNRS/L 318 MVJNR/L 318 MWLNR/L 319 SCLCR/L 319 SDJCR/L 320 SSDCN 320 SVJCR/L 320 SWLCR/L 320 MICRO 100 CARIDE 322 Clamp CL-20 $2.98 CL-20 $2.98 CL-20 $2.98 CL-20 $2.98 CL-20 $2.98 Clamp Screw TO-ACS3 $4.02 TO-ACS3 $4.02 TO-ACS4 $4.02 TO-ACS4 $4.02 Clamp Screw XNS-48 $0.74 XNS-48 $0.74 XNS-48 $0.74 XNS-48 $0.74 XNS-48 $0.74 Wrench TO-P-3 $0.52 TO-P-3 $0.52 TO-P-4 $0.52 TO-P-4 $0.52 A

47 OD TURNING HOLDERS-MCLNR/L, MDPNN, MSDNN MCRNR/L 15 Side Cutting, Offset Negative Rake Using CNMG, CNMA, CNG_ & CNM_ type inserts Industry Reference MDPNN 27.5 Side Cutting Straight Negative Rake Using DNMG, DNMA, DNG_ & DNM_ type inserts CNMG Inserts on Pages A C Right Hand Model Left Hand Model Uses Inserts MCRNR/L-124 3/4 SQ 5 TH-1130 TH-2130 $43.68 CNMG-43 MCRNR/L-164D 1 SQ 6 TH-1135 TH-2135 $43.68 CNMG-43 MCRNR/L-165D 1 SQ 6 TH-1140 TH-2140 $43.68 CNMG-54 MCRNR/L-205D 1-1/4 SQ 6 TH-1145 TH-2145 $47.97 CNMG-54 DNMG Inserts on Pages 327 Industry Reference A C Neutral Hand Model EXTRA HARDWARE Seat ICSN-433 $2.76 ICSN-433 $2.76 ICSN-533 $3.38 ICSN-533 $3.38 Inserts Seat MDPNN-164D 1 SQ 6 TH-1170 $65.16 DNMG-43 MDPNN-165D 1 SQ 6 TH-1175 $65.16 DNMG-54 MDPNN-204D 1-1/4 SQ 6 TH-1180 $72.16 DNMG-43 MDPNN-205D 1-1/4 SQ 6 TH-1185 $72.16 DNMG-54 MDPNN-855D 1 X 1-1/4 6 TH-1190 $65.16 DNMG-54 IDSN-433 $2.50 IDSN-533 $3.80 IDSN-433 $2.50 IDSN-533 $3.80 IDSN-533 $3.80 Lock Pin NL-46 $1.90 NL-46 $1.90 NL-58 $1.90 NL-58 $1.90 EXTRA HARDWARE Lock Pin NL-46 $1.90 NL-58 $1.90 NL-46 $1.90 NL-58 $1.90 NL-58 $1.90 Clamp CL-9 $2.98 CL-9 $2.98 CL-9 $2.98 CL-9 $2.98 Clamp CL-6 $2.98 CL-12 $2.98 CL-12 $2.98 CL-12 $2.98 CL-12 $2.98 Clamp Screw XNS-58 $0.74 XNS-58 $0.74 XNS-510 $0.74 XNS-510 $0.74 Clamp Screw XNS-36 $0.74 XNS-510 $0.74 XNS-510 $0.74 XNS-510 $0.74 XNS-510 $0.74 CARIDE INSERTS MSDNN 45 Side Cutting Straight Negative Rake Using SNMG, SNGA, SNMA & SNM_ type inserts SNMG Inserts on Pages 329 Industry Reference A C Neutral Hand Model Inserts Seat MSDNN-103 5/8 SQ 5 TH-1195 $36.07 SNMG-33 MSDNN-123 3/4 SQ 5 TH-1200 $41.06 SNMG-33 MSDNN-124 3/4 SQ 5 TH-1205 $41.06 SNMG-43 MSDNN-164D 1 SQ 6 TH-1210 $43.68 SNMG-43 MSDNN-165D 1 SQ 6 TH-1215 $43.68 SNMG-54 ISSN-322 $1.70 ISSN-322 $1.70 ISSN-433 $2.70 ISSN-433 $2.70 ISSN-533 $3.20 EXTRA HARDWARE Lock Pin NL-34 $1.90 NL-34 $1.90 NL-46 $1.90 NL-46 $1.90 NL-58 $1.90 Clamp CL-6 $2.98 CL-6 $2.98 CL-9 $2.98 CL-9 $2.98 CL-12 $2.98 Clamp Screw XNS-36 $0.74 XNS-36 $0.74 XNS-59 $0.74 XNS-59 $0.74 XNS-510 $ Master Catalog 315 DEURRING

48 CHUCK JAWS LATHE WORKHOLDING OD TURNING HOLDERS-MDJNR/L, ADJNR/L & MTANR/L MDJNR/L -3 Side Cutting Offset Negative Rake Using DNMG, DNMA, DNG_ & DNM_ type inserts MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS DNMG Inserts on Pages 327 Industry Reference A C Right Hand Model Left Hand Model Inserts Seat MDJNR/L-124 3/4 SQ 5 TH-1150 TH-2150 $63.63 DNMG-43 MDJNR/L-164D 1 SQ 6 A-TYPE TOOLHOLDERS ADJNR/L One action double clamping Strong and positive clamping power Fewer parts High accuracy TH-1155 TH-2155 $65.16 DNMG-43 MDJNR/L-204D 1-1/4 SQ 6 TH-1160 TH-2160 $72.15 DNMG-43 MDJNR/L-854D 1 X 1-1/4 6 TH-1165 TH-2165 $65.16 DNMG-43 Increase Insert Life! Quick Change EXTRA HARDWARE IDSN-433 $2.50 IDSN-433 $2.50 IDSN-433 $2.50 IDSN-433 $2.50 Lock Pin NL-46 $1.90 NL-46 $1.90 NL-46 $1.90 NL-46 $1.90 Clamp CL-6 $2.98 CL-20 $2.98 CL-20 $2.98 CL-20 $2.98 Clamp Screw XNS-36 $0.74 XNS-48 $0.74 XNS-48 $0.74 XNS-48 $0.74 A INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD DNMG Inserts on Pages 327 Right Hand Model TO-ADJNR12-3 $75.00 TO-ADJNR16-3 $85.00 TO-ADJNR12-4 $75.00 TO-ADJNR16-4 $85.00 MTANR/L Left Hand Model TO-ADJNL12-3 $75.00 TO-ADJNL16-3 $85.00 TO-ADJNL12-4 $75.00 TO-ADJNL16-4 $ Side Cutting Straight Negative Rake Using TNMG, TNMP, TNG_ & TNM_ type inserts Industry Reference b h h1 r1 f Applicable Insert DN 33 _ DN 33 _ DN 43 _ DN 43 _ TNMG Inserts on Pages 328 A Shim or Seat TO-ELSD32 $6.39 TO-ELSD32 $6.39 TO-LSD42 $7.26 TO-LSD42 $7.26 Spring Pin TO-LSP3 $0.68 TO-LSP3 $0.68 TO-LSP4 $0.68 TO-LSP4 $ Master Catalog C Right Hand Model Left Hand Model Spring TO-P-7 $0.86 TO-P-7 $0.86 TO-P-9 $0.86 TO-P-9 $0.86 Inserts Seat MTANR/L-123 3/4 SQ 4 TH-1220 TH-2220 $41.05 TNMG-33 MTANR/L-164D 1 SQ 6 TH-1225 TH-2225 $43.68 TNMG-43 Clamp TO-APS3 N/A TO-APS3 N/A TO-ACP4 $6.59 TO-ACP4 $6.59 Clamp Screw TO-ACS3 $4.02 TO-ACS3 $4.02 TO-ACS4 $4.02 TO-ACS4 $4.02 EXTRA HARDWARE ITSN-322 $1.90 ITSN-433 $3.10 Lock Pin NL-34L $1.90 NL-34 $1.90 Clamp CL-6 $2.98 CL-9 $2.98 Wrench TO-P-3 $0.52 TO-P-3 $0.52 TO-P-4 $0.52 TO-P-4 $0.52 Clamp Screw XNS-36 $0.74 XNS-59 $0.74

49 OD TURNING HOLDERS-MTENNS, MTFNR/L, MTGNR/L MTENN 30 Side Cutting Straight Negative Rake Using TNMG, TNMA, TNG_ & TNM_ type inserts MTFNR/L 0 End Cutting Solid Steel ar Negative Rake Using TNMG, TNMA, TNG_ & TNM_ type inserts TNMG Inserts on Pages 328 Industry Reference A C Neutral Hand Model Inserts Seat MTENN-103 5/8 SQ 4 TH-1230 $36.08 TNMG-33 MTENN-123 3/4 SQ 4 TH-1235 $41.05 TNMG-33 MTENN-124 3/4 SQ 4 TH-1240 $41.05 TNMG-43 MTENN-164D 1 SQ 6 TH-1245 $43.68 TNMG-43 MTENN-853C 1 x 1-1/4 6 TH-1250 $48.40 TNMG-33 ITSN-323 $1.90 ITSN-323 $1.90 ITSN-433 $3.10 ITSN-433 $3.10 ITSN-323 $1.90 EXTRA HARDWARE Lock Pin NL-34L $1.90 NL-34L $1.90 NL-46 $1.90 NL-46 $1.90 NL-34L $1.90 Clamp CL-6 $2.98 CL-6 $2.98 CL-9 $2.98 CL-9 $2.98 CL-6 $2.98 Clamp Screw XNS-36 $0.74 XNS-36 $).74 XNS-59 $0.74 XNS-59 $0.74 XNS-36 $0.74 MTGNR/L TNMG Inserts on Pages 328 Industry Reference 0 Side Cutting Offset Negative Rake Using TNMG, TNMA, TNG_ & TNM_ type inserts A C Right Hand Model Left Hand Model Inserts Seat MTFNR/L-123 3/4 SQ 5 TH-1255 TH-2255 $41.06 TNMG-33 MTFNR/L-163C 1 SQ 5 TH-1260 TH-2260 $43.68 TNMG-33 MTFNR/L-164D 1 SQ 6 TH-1265 TH-2265 $43.68 TNMG-43 TNMG Inserts on Pages 328 Industry Reference A C Right Hand Model Left Hand Model EXTRA HARDWARE ITSN-323 $1.90 ITSN-323 $1.90 ITSN-433 $3.10 Inserts Seat MTGNR/L-123 3/4 SQ 5 TH-1270 TH-2270 $41.06 TNMG-33 MTGNR/L-163C 1 SQ 5 TH-1275 TH-2275 $43.68 TNMG-33 MTGNR/L-164D 1 SQ 6 TH-1280 TH-2280 $43.68 TNMG-43 Lock Pin NL-34L $1.90 NL-34L $1.90 NL-46 $1.90 EXTRA HARDWARE ITSN-323 $1.90 ITSN-323 $1.90 ITSN-433 $3.10 Lock Pin NL-34L $1.90 NL-34L $1.90 NL-46 $1.90 Clamp CL-6 $2.98 CL-6 $2.98 CL-9 $2.98 Clamp CL-6 $2.98 CL-6 $2.98 CL-9 $2.98 Clamp Screw XNS-36 $0.74 XNS-36 $0.74 XNS-510 $0.74 Clamp Screw XNS-36 $0.74 XNS-36 $0.74 XNS-510 $ Master Catalog 317 CARIDE INSERTS DEURRING

50 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS OD TURNING HOLDERS-ATGNR/L, MTJNR/L, MVJNR/L A-Type Toolholders ATGNR/L One action double clamping Strong and positive clamping power Fewer parts High accuracy TNMG Inserts on Pages 328 Right Hand Model TO-ATGNR12-3 $75.00 TO-ATGNR16-3 $85.00 TO-ATGNR16-4 $85.00 MTJNR/L -3 Side Cutting Offset Negative Rake Using TNMG, TNMA, TNG_ & TNM_ type inserts Left Hand Model TO-ATGNL12-3 $75.00 TO-ATGNL16-3 $85.00 TO-ATGNL16-4 $85.00 b h h1 r1 f TNMG Inserts on Pages 328 Increase Insert Life! Quick Change Applicable Insert 1 TN 33 _ TN 33 _ TN 43 _ Shim or Seat TO-LST317 $5.00 TO-LST317 $5.00 TO-LST42 $7.14 Spring Pin TO-LSP3 $0.68 TO-LSP3 $0.68 TO-LSP4 $0.68 Spring TO-P-7 $0.86 TO-P-7 $0.86 TO-P-4 $0.86 Clamp TO-ACP3 $5.20 TO-ACP3 $5.20 TO-ACP4 $6.59 EXTRA HARDWARE Clamp Screw TO-ACS3 $4.02 TO-ACS3 $4.02 TO-ACS4 $4.02 Wrench TO-P-3 $0.52 TO-P-3 $0.52 TO-P-4 $0.52 A INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD MVJNR/L Industry Reference -3 Side Cutting Offset Negative Rake Using VNMG, VNMA, VNG_ & VNM_ type inserts A Master Catalog C Right Hand Model Left Hand Model Inserts Seat MTJNR/L-123 3/4 SQ 5 TH-1285 TH-2285 $41.05 TNMG-33 MTJNR/L-164D 1 SQ 6 TH-1290 TH-2290 $43.68 TNMG-43 MTJNR/L-204D 1-1/4 SQ 7 TH-1295 TH-2295 $47.97 TNMG-43 VNMG Inserts on Page 329 Industry Reference A C Right Hand Model Left Hand Model ITSN-323 $1.90 ITSN-433 $3.10 ITSN-433 $3.10 Inserts Seat MVJNR/L-123 3/4 SQ 5 TH-1300 TH-2300 $67.13 VNMG-33 MVJNR/L-163C 1 SQ 5 TH-1305 TH-2305 $68.43 VNMG-33 MVJNR/L-164D 1 SQ 6 TH-1310 TH-2310 $68.43 VNMG-43 MVJNR/L-203D 1-1/4 SQ 6 TH-1315 TH-2315 $75.87 VNMG-33 MVJNR/L-204D 1-1/4 SQ 6 TH-1320 TH-2320 $75.87 VNMG-43 Lock Pin NL-34L $1.90 NL-46 $1.90 NL-46 $1.90 Clamp CL-6 $2.98 CL-9 $2.98 CL-9 $2.98 EXTRA HARDWARE IVSN-323 $2.24 IVSN-323 $2.24 IVSN-433 $2.98 IVSN-323 $2.24 IVSN-433 $2.98 Lock Pin NL-34L $1.90 NL-34L $1.90 NL-46 $1.90 NL-34L $1.90 NL-46 $1.90 Clamp CL-30 $5.26 CL-30 $5.26 CL-30 $5.26 CL-30 $5.26 CL-30 $5.26 Clamp Screw XNS-36 $0.74 XNS-510 $0.74 XNS-510 $0.74 Clamp Screw XNS-510 $0.74 XNS-510 $0.74 XNS-510 $0.74 XNS-510 $0.74 XNS-510 $0.74

51 OD TURNING HOLDERS-MWLNR/L, AWLNR/L MWLNR/L -5 Side & End Cutting Offset Negative Rake Using WNGG, WNMA, & WNMG type inserts Industry Reference One action double clamping Strong and positive clamping power Fewer parts High accuracy WNMG Inserts on Pages 330 A-TYPE TOOLHOLDERS AWLNR/L A C Right Hand Model Left Hand Model Inserts Seat MWLNR/L-123 3/4 SQ 5 TH-1325 TH-2325 $41.05 WNMG-33 MWLNR/L-124 3/4 SQ 5 TH-1330 TH-2330 $41.05 WNMG-43 MWLNR/L-163C 1 SQ 6 TH-1335 TH-2335 $43.68 WNMG-33 MWLNR/L-164D 1 SQ 6 TH-1340 TH-2340 $43.68 WNMG-43 MWLNR/L-204D 1-1/4 SQ 6 TH-1350 TH-2350 $47.97 WNMG-43 Increase Insert Life! Quick Change EXTRA HARDWARE IWSN-323 $2.52 IWSN-433 $3.40 IWSN-323 $2.52 IWSN-433 $3.40 IWSN-433 $3.40 Lock Pin NL-34L $1.90 NL-46 $1.90 NL-34L $1.90 NL-46 $1.90 NL-46 $1.90 Clamp CL-6 $2.98 CL-9 $2.98 CL-6 $2.98 CL-9 $2.98 CL-9 $2.98 Clamp Screw XNS-36 $0.74 XNS-59 $0.74 XNS-36 $0.74 XNS-59 $0.74 XNS-59 $0.74 A WNMG Inserts on Pages 330 b h h1 r1 f SCLCR/L -5 Side & End Cutting, Offset 7 Relief Angle, S-Lock Using CCMT type inserts Right Hand Model TO-AWLNR12-3 $75.00 TO-AWLNR16-3 $85.00 TO-AWLNR12-4 $75.00 TO-AWLNR16-4 $85.00 For CCMT Inserts, Please See Page 331 Industry Reference A C Left Hand Model TO-AWLNL12-3 $75.00 TO-AWLNL16-3 $85.00 TO-AWLNL12-4 $75.00 TO-AWLNL16-4 $85.00 F Right Hand Model Applicable Inserts WN 33 _ WN 33 _ WN 43 _ WN 43 _ Left Hand Model Shim or Seat TO-LSW312 $8.95 TO-LSW312 $8.95 TO-LSW42 $9.18 TO-LSW42 $9.18 Spring Pin TO-LSP3 $0.68 TO-LSP3 $0.68 TO-LSP4 $0.68 TO-LSP4 $0.68 Spring Clamp Clamp Wrench TO-P-7 $0.86 TO-P-7 $0.86 TO-P-9 $0.86 TO-P-9 $0.86 TO-ACP3 $5.20 TO-ACP3 $5.20 TO-ACP4 $6.59 TO-ACP4 $6.59 TO-ACS3 $4.02 TO-ACS3 $4.02 TO-ACS4 $4.02 TO-ACS4 $4.02 Uses Inserts TO-P-3 $0.52 TO-P-3 $0.52 TO-P-4 $0.52 TO-P-4 $ Master Catalog 319 Torx Key Insert Screw SCLCR/L L06-2J 3/8 SQ TH-1505 TH-2505 $34.92 CCMT-21.5 T-7 TS M1 SCLCR/L L08-3A 1/2 SQ TH-1510 TH-2510 $34.92 CCMT-32.5 T-15 TS M1 SCLCR/L L10-3 5/8 SQ TH-1515 TH-2515 $35.74 CCMT-32.5 T-15 TS M1 SCLCR/L L12-3 3/4 SQ TH-1520 TH-2520 $42.51 CCMT-32.5 T-15 TS M1 SCLCR/L L16-3D 1 SQ TH-1525 TH-2525 $42.51 CCMT-32.5 T-15 TS M1 CARIDE INSERTS DEURRING

52 CHUCK JAWS LATHE WORKHOLDING SWISS STYLE - OD TURNING HOLDERS SDJCR/L -3 Side Cutting, Offset 11 Relief Angle, Screw Down Using DCMT type inserts MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS SSDCN Industry Reference A C F Right Hand Model Left Hand Model Uses Inserts Torx Key Insert Screw SDJCR/L L06-2J 3/8 SQ TH-1530 TH-2530 $42.72 DCMT-21.5 T-7 TS M1 SDJCR/L L08-2A 1/2 SQ TH-1535 TH-2535 $42.72 DCMT-21.5 T-7 TS M1 SDJCR/L L08-3A 1/2 SQ TH-1540 TH-2540 $42.72 DCMT-32.5 T-15 TS M1 SDJCR/L L10-3 5/8 SQ TH-1545 TH-2545 $44.33 DCMT-32.5 T-15 TS M1 SDJCR/L L12-3 3/4 SQ TH-1550 TH-2550 $55.42 DCMT-32.5 T-15 TS M1 SDJCR/L L16-3D 1 SQ TH-1555 TH-2555 $57.46 DCMT-32.5 T-15 TS M1 45 Side Cutting Straight 7 Relief Angle, S-Lock Using SCMT type inserts TOOLHOLDERS INDEXALE DRILLS TURNING & ORING SVJCR/L -3 Side Cutting Offset 5 Relief Angle, S-Lock Using VCMT type inserts Industry Reference A C Neutral Hand Model Uses Inserts Torx Key Insert Screw SSDCN08-3A 1/2 SQ 4.0 TH-1560 $34.92 SCMT-32.5 T-15 TS M1 SSDCN10-3 5/8 SQ 4.5 TH-1565 $35.74 SCMT-32.5 T-15 TS M1 SSDCN12-3 3/4 SQ 4.5 TH-1570 $42.51 SCMT-32.5 T-15 TS M1 ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SWLCR/L Industry Reference -5 Side & End Cutting Offset 7 Relief Angle, S-Lock Using WCMT type inserts A C Master Catalog F Right Hand Model Left Hand Model Uses Inserts Torx Key Insert Screw SVJCR/L L12-3 3/ TH-1575 TH-2575 $62.11 VCMT-33 T-15 TS M1 SVJCR/L L16-3D TH-1580 TH-2580 $63.58 VCMT-33 T-15 TS M1 SVJCR/L L20-3D 1 1/ TH-1585 TH-2585 $68.35 VCMT-33 T-15 TS M1 Industry Reference A C F Right Hand Model Left Hand Model Uses Inserts Torx Key Insert Screw SWLCR/L L06-2J 3/ TH-1605 TH-2605 $34.92 WCMT-21.5 T-7 TS M1 SWLCR/L L08-3A 1/ TH-1590 TH-2590 $34.92 WCMT-32.5 T-15 TS M1 SWLCR/L L10-3 5/ TH-1595 TH-2595 $35.75 WCMT-32.5 T-15 TS M1 SWLCR/L L16-3D TH-1600 TH-2600 $45.30 WCMT-32.5 T-15 TS M1 SWLCR-L L12-3 3/ TH-1610 TH-2610 $42.50 WCMT-32.5 T-15 TS M1

53 SWISS STYLE OD TURNING HOLDERS INDEXALE INSERT HOLDERS TURNING & FACING TOOLS FEATURES: Durable and unique chrome nickel toolholder Positive chip control Coolant-thru hole design holder includes torx screw and torx key HEX WRENCH SETS 90 TURNING & FACING-95 APPROACH- Uses CCMT Inserts (not included) Toolholder Nomenclature Square F Over Insert Right Hand Left Hand SCLCR/L 0404 D2 1/4 2 1/2.394 MI MI $34.95 SCLCR/L 0505 D2 5/16 2 1/2.394 MI MI $37.90 SCLCR/L 0606 E2 3/8 2 3/4.472 MI MI $42.60 SCLCR/L 0808 F2 1/ MI MI $46.60 SCLCR/L 1010 H2 5/ MI MI $ TURNING & FACING- Uses DCMT Inserts (not included) Toolholder Nomenclature Square F Over Insert Right Hand Left Hand SDJCR/L 0505 H2 5/ MI MI $42.60 SDJCR/L 0606 H2 3/ MI MI $49.90 SDJCR/L 0808 H2 1/ MI MI $52.50 SDJCR/L 1010 H2 5/ MI MI $58.25 Full Line Available! Please call for more information. WORK STOP Type No. Of Pieces Inch 12 Inch 13 Hex Wrench Set Includes.050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1 / 4, 5/16.050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1 / 4, 5/16, 3/8 O $7.20 O $8.20 Metric 9 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm O $7.76 Combo Pack 13 & 9 Inch & Metric Set O $15.12 Stop-Loc Pat.Pend. CARIDE INSERTS FLEXILE SHAFT HALOGEN LIGHTS A V/ 60Hz/ 1Ph 24 flexible arm Powerful magnetic base with bolt on bracket 24 FLEXILE SHAFT # A $59.00 Replacement ulb: # A $11.00 ea Adjustable Precision-Gage lengths up to 5-1/2 long holding +/-.005 Save Money! No more fixed length dedicated shop-made front collet stops for each job Versatile-For use on CNC or manual lathes whether you are running a bar manually or using a bar puller. Can also be used on mill vises! Consistency-Unique design incorporates self-centering, unobstructed viewing and contrasting colors to give user confidence by feeling and seeing that the dimension is being controlled Made in A STOP-LOC Chuck/Collet/Work Stop Inch Style # STOPLOC $16.95 each With Metric/Thous # STOPLOC-MM $22.95 each 110V/ 60Hz/ 1Ph 35 watts 20 flexible arm Powerful magnetic base with on/off switch 20 FLEXILE SHAFT # A $49.00 Replacement ulb: # A $10.00 ea Master Catalog 321 DEURRING

54 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES INDEXALE TURNING TOOLHOLDERS INDEXALE INSERT HOLDERS CHROME NICKEL TOOLHOLDERS 75 THRU-TURNING Utilizing 100 Unused RH Cutting Corner Uses CCMT Inserts (not included) FEATURES: Durable and unique chrome nickel toolholder Positive chip control Coolant-thru hole design holder includes torx screw and torx key 75 THRU-TURNING TOOLS Toolholder Nomenclature Square F Over Insert SCCR 0404 D2 1/4 2 1/2.267 MI $34.95 SCCR 0505 D2 5/16 2 1/2.267 MI $37.90 SCCR 0606 E2 3/8 2 3/4.330 MI $42.60 SCCR 0808 F2 1/ MI $46.60 SCCR 1010 H2 5/ MI $51.65 RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING 75 THRU-FACING Utilizing 100 Unused LH Cutting Corner Uses CCMT Inserts (not included) TURNING & CHAMFERING 50 Right Hand & Left Hand Uses CCMT Inserts (not included) 75 THRU-FACING TOOLS Toolholder Nomenclature Square F Over Insert SCKCR 0404 D2 1/4 2 1/2.394 MI $34.95 SCKCR 0505 D2 5/16 2 1/2.394 MI $37.90 SCKCR 0606 E2 3/8 2 3/4.472 MI $42.60 SCKCR 0808 F2 1/ MI $46.60 SCKCR 1010 H2 5/ MI $ RH/LH TURNING & CHAMFERING TOOLS Toolholder Nomenclature Square F Over Insert SCMCN 0404 D2 1/4 2 1/2.157 MI $34.95 SCMCN 0505 D2 5/16 2 1/2.157 MI $37.90 SCMCN 0606 E2 3/8 2 3/4.189 MI $42.60 SCMCN 0808 F2 1/ MI $46.60 SCMCN 1010 H2 5/ MI $51.65 ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD CHAMFERING 45 Right Hand & 55 Left Hand Uses CCMT Inserts (not included) 55 THREADING V Turning Uses DCMT Inserts (not included) 45 RH & 55 LH CHAMFERING TOOLS Toolholder Nomenclature Square Master Catalog F Over Insert SCSCR 0404 D2 1/4 2 1/2.157 MI $34.95 SCSCR 0505 D2 5/16 2 1/2.157 MI $37.90 SCSCR 0606 E2 3/8 2 3/4.189 MI $42.60 SCSCR 0808 F2 1/ MI $46.60 SCSCR 1010 H2 5/ MI $ THREADING TOOLS- V TURNING Toolholder Nomenclature Square F Over Insert SDNCN 0505 H2 5/ MI $42.60 SDNCN 0606 H2 3/ MI $49.90 SDNCN 0808 H2 1/ MI $52.50 SDNCN 1010 H2 5/ MI $58.25

55 OD TOOLHOLDER PARTS DIFFERENTIAL SCREWS ICSN IDSN IRSN IVSN ISSN ITSN IWSN LOCK PINS A C H T /32 5/16-24 CS /16 3/8-24 CS-32 $ /8 1/4-28 CS / CS / LS-20 $ / LS-21 $ /8 1/4-28 LS-30 $ /8 1/4-28 LS-33 $ /32 5/16-24 LS / MS /8 1/4-28 MS /8 1/4-28 MS /8 1/4-28 MS /32 5/16-24 MS /32 5/16-24 MS /16 3/8-24 MS-610 $ /32 5/16-24 STC / STC /32 5/16-24 STC / STC /8 1/4-28 STC /16 3/8-24 STC-19 $ /8 1/4-28 STC / STC-27 $ /8 1/4-28 STC-32 $ / XNS-26 $ / XNS / XNS / XNS / XNS /8 1/4-28 XNS /8 1/4-28 XNS /8 1/4-28 XNS /32 5/16-24 XNS /32 5/16-24 XNS /32 5/16-24 XNS /32 5/16-24 XNS /16 3/8-24 XNS-610 $2.52 SHIM SEATS STYLE/ PART NO. INSERT I.C. T R ICSN-432 1/2 3/16 1/32 $2.76 ICSN-433 1/2 3/16 3/64 $2.76 ICSN-533 5/8 3/16 3/64 $3.38 ICSN-633 3/4 3/16 3/64 $3.90 ICSN-643 3/4 1/4 3/64 $5.30 IDSN-433 1/2 3/16 3/64 $2.50 IDSN-533 5/8 3/16 3/64 $3.80 IDSN-543 5/8 1/4 3/64 $4.36 IRSN-32 3/8 1/8 - $2.10 IRSN-43 1/2 3/16 - $2.20 IRSN-44 1/2 1/4 - $3.30 IRSN-53 5/8 3/16 - $3.50 IRSN-63 3/4 3/16 - $3.98 IRSN /4 - $7.90 IVSN-322 3/8 1/8 1/32 $2.24 IVSN-324 3/8 1/8 1/16 $2.24 IVSN-432 1/2 3/16 1/32 $2.98 IVSN-433 1/2 3/16 3/64 $2.98 Reference s Sandvik CLAMPS Kennametal Inser t I.C. STYLE/ PART NO. L H T INSERT I.C. MN-43-1/ / NL-43 $1.90 MN-44 KL-44 1/ /32 1/4-28 NL-44 $1.90 MN-46 KL-46 1/ /32 1/4-28 NL-46 $1.90 MN-46L KL-46L 1/ /32 1/4-28 NL-46L $ / /8 5/16-24 NL-55 $5.00 MN-56-5/ /8 5/16-24 NL-56 $ / /8 5/16-24 NL-57 $4.20 MN-58 KL-58 5/ /8 5/16-24 NL-58 $ / /8 5/16-24 NL-58L $4.20 MN-66-3/ /64 3/8-24 NL-66 $3.00 MN-66L - 3/ /64 3/8-24 NL-66L $3.90 MN-68 KL-68 3/ /64 3/8-24 NL-68 $1.90 MN-68L KL-68L 3/ /64 3/8-24 NL-68L $ /32 7/16-20 NL-808 $5.00 MN /32 7/16-20 NL-810 $ / /32 9/16-18 NL-1010 $13.98 T R ISSN-322 3/8 1/8 1/32 $1.70 ISSN-323 3/8 1/8 3/64 $1.70 ISSN-433 1/2 3/16 3/64 $2.70 ISSN-434 1/2 3/16 1/16 $2.70 ISSN-443 1/2 1/4 3/64 $3.30 ISSN-533 5/8 3/16 3/64 $3.20 ISSN-633 3/4 3/16 3/64 $3.80 ISSN-643 3/4 1/4 3/64 $5.50 ITSN-322 3/8 1/8 1/32 $1.90 ITSN-323 3/8 1/8 3/64 $1.90 ITSN-333 3/8 3/16 3/64 $2.00 ITSN-432 1/2 3/16 1/32 $3.10 ITSN-433 1/2 3/16 3/64 $3.10 ITSN-434 1/2 3/16 1/16 $3.10 ITSN-443 1/2 1/4 3/64 $4.00 ITSN-533 5/8 3/16 3/64 $3.98 ITSN-534 5/8 3/16 1/16 $3.98 ITSN-633 3/4 3/16 3/64 $5.40 ITSN-636 3/4 3/16 3/32 $5.40 IWSN-323 3/8 1/8 3/64 $2.52 IWSN-433 1/2 3/16 3/64 $3.40 CARIDE INSERTS REFERENCE NUMERS Sandvik Kennametal HARDWARE SOLD IN PACKAGES OF 10 Insert I.C. L H T - - 5/ / NL-2.52 $3.96 MN-23 KL-23 1/ / NL-23 $1.90 MN-33 KL-33 3/ / NL-33 $1.90 MN-33L KL-33L 3/ / NL-33L $1.90 MN-34 KL-34 3/ / NL-34 $1.90 MN-34L KL-34L 3/ / NL-34L $1.90 L CLAMP REFERENCE NUMERS Sandvik Kennametal Valenite A C D T CL-5 $2.98 MC-6 CK-6 CLI CL-6 $ CLI CL-7 $2.98 MC-9 CK-9 CLI /16-24 CL-9 $2.98 MC-12 CK-12 CLI /16-24 CL-12 $2.98 MC-19 CK-19 CLI CL-19 $3.72 MC-20 CK-20 CLI /4-28 CL-20 $ /4-28 CL-21 $ /4-28 CL-22 $ CLI /8-24 CL-24 $5.26 MC-30 CK-30 CLI /16-24 CL-30 $5.26 MC /16-24 CL-41 $2.98 MC /16-24 CL-42 $ /4-28 CL-43 $ /4-28 CL-44 $ /8-24 CL-45 $5.26 MC /16-24 CL-46 $ CL-48 $ Master Catalog 323 DEURRING

56 CHUCK JAWS LATHE WORKHOLDING TUNGALOY INSERTS TUNGALOY INSERT GRADES Featuring AH120-The Super Grade! Special PVD TiAlN coated carbide combined with super tough substrate. Ideal for general turning of steels, stainless and super alloys! MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING CERMET GRADES Cermet Properties Application NS530 AT530 Has high wear resistant and excellent thermal and mechanical shock resistance.performs well in wet cutting TiAlN coated cermet. Provides superior resistance to flank wear and adhesive wear General purpose grade covering a wide range of cutting conditions from low to high speeds for various steels Suitable for high speed turning of steels and stainless steels requiring better surface roughness and longer tool life COATED CARIDE GRADES Coated Carbide Properties Application T9105 Ti + AlOxide; DISK Technology substrate with advanced coating High speed cutting of steels and cast irons T9115 Ti + AlOxide; DISK Technology substrate with advanced coating For general purpose turning of steels and stainless steels T9125 T9135 Ti + AlOxide; DISK Technology substrate with advanced coating Ti + AlOxide; DISK Technology substrate with advanced coating For general purpose turning of steels and stainless steels including interrupted and heavy cutting For general purpose turning of steels and stainless steels including severly interrupted and heavy cutting of steels T6020 Ti + AlOxide; tough substrate with new advanced coating For general purpose turning of steels and stainless steels T6030 Ti + AlOxide; extra tough substrate with advanced coating For rough and heavy turning of stainless steels T5020 Ti + AlOxide; well balanced wear resistance and toughness Roughing and interrupted turning of cast irons SH730 Coated carbide with advanced coating Ideal for stainless steels AH110 AH120 TiAlN coating; heat resistant coating and hard substrate allows excellent wear resistance TiAlN coating; heat resistant coating and extremely hard substrate allows highest wear resistance Turning of super (high temp) alloys and Non ferrous metals Turning and Milling of super (high temp) alloys, steels, stainless steels - great all purpose grade. GH330 TiCnO Coated carbide General milling and turning of steels UNCOATED CARIDE GRADES Uncoated Carbide Properties Application KS05F Uncoated carbide with good overall wear resistance Ideal for Aluminum TH10 K10(C2) type uncoated carbide - good overall wear resistance General turning of Non Ferrous materials H10T Used for positive (boring) inserts; K10(C2) type uncoated carbide - good overall wear resistance and toughness TUNGALOY INSERT CHIPREAKERS General boring of Non Ferrous materials ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Chip reakers TS TM TH SS SM SA P PM PP PS 28 Descriptions For Finishing - landless sharp cutting edges and large rake angle; excellent all round chipbreaker for finishing Steels For Medium cutting - unique breaker geometry with sharp cutting edges and large rake angle assures free cutting action in a wide range of cutting conditions - excellent for medium cutting of steels and super (high temp) alloys For Heavy cutting Double sided 3 dimensional chipbreaker with a wide land and broad groove used for medium to heavy cutting including interrupted cuts and in poor conditions - excellent for heavy and interrupted cutting of steels, stainless and super ( high temp) alloys For finishing - 3 dimensional chipbreaker with a large rake angle; very free cutting and most suitable for stainless steels and mild steels For Medium cutting - 3 dimensional chipbreaker offers low cutting forces over a wide range of cutiing conditions - especially suited for medium cutting of stainless steels and mild steels For finishing - designed to reduce contact area between tool and chip, preventing the insert from raising temperature during cutting - designed especially for medium cutting of stainless steels and super (high temp) alloys For non ferrous metals - very sharp cutting edges 3 dimensional chipbreaker - has positive yet strong edge, provides good chip control for medium to rough cutting. For general boring of Non Ferrous metals - high positive rake and very sharp cutting edges - low cutting forces and no chatter For finish to medium boring on positive inserts - steels, stainless steels For general turning of Non ferrous metals - high positive rake angle for low cutting forces and excellent shearing ability - also effective for stainless steels and super (high temp) alloys Master Catalog

57 CNMG 80 DIAMOND TURNING INSERTS CNMG INSERTS FOR STEELS 80 mond uy In ox Quantities & Save! ANSI ISO IC (Inch) T (Inch) CNMG431 CNMG /2 3/16 CNMG432 CNMG /2 3/16 R (Inch) / /32 Cutting Conditions Cont Operation/ Application Semi Finish Chip reaker Grade 1-9 Pcs ox NS530 TO-1317 $6.80 $5.29 Cont Semi Finish AT530 TO-1315 $8.19 $6.37 TS Cont - GP Semi Finish T9115 TO-3516 $9.32 $7.25 Cont & Int Semi Finish T9125 TO-3517 $9.32 $7.25 Cont - GP Medium T9115 TO-3513 $9.32 $7.25 Cont & Int Medium TM T9125 TO-3514 $9.32 $7.25 Severely Int & Heavy Cutting Medium T9135 TO-3515 $9.32 $7.25 Cont Semi Finish NS530 TO-1397 $6.80 $5.29 Cont Semi Finish AT530 TO-1395 $8.19 $6.37 TS Cont - GP Semi Finish T9115 TO-3527 $9.32 $7.25 Cont & Int Semi Finish T9125 TO-3528 $9.32 $7.25 Cont - GP Medium T9115 TO-3524 $9.32 $7.25 Cont & Int Medium TM T9125 TO-3525 $9.32 $7.25 Severely Int & Heavy Cutting Medium T9135 TO-3526 $9.32 $7.25 Cont - GP Heavy T9115 TO-3520 $9.32 $7.25 Cont & Int Heavy TH T9125 TO-3521 $9.32 $7.25 Severely Int & Heavy Cutting Heavy T9135 TO-3522 $9.32 $7.25 CNMG434 CNMG /2 3/ Cont - High Speed Heavy TH T9105 TO-3539 $9.32 $7.25 CNMG433 CNMG /2 3/16 CNMG543 CNMG /8 1/4 CNMG544 CNMG /8 1/ / / /16 CNMG INSERTS FOR STAINLESS STEELS 80 mond Cont - GP Medium T9115 TO-3536 $9.32 $7.25 Severely Int & Heavy Cutting Medium TM T9135 TO-3538 $9.32 $7.25 Severely Int & Heavy Cutting Heavy T9135 TO-3534 $9.32 $7.25 Cont & Int Medium TM T9125 TO-3548 $15.39 $11.97 Cont & Int Heavy T9125 TO-3545 $15.39 $11.97 TH Severely Int & Heavy Cutting Heavy T9135 TO-3546 $15.39 $11.97 Cont - General Purpose Heavy Turning T9115 TO-3550 $15.39 $11.97 TH Severely Int & Heavy Cutting Heavy Turning T9135 TO-3552 $15.39 $11.97 uy In ox Quantities & Save! CARIDE INSERTS ANSI ISO IC (Inch) T (Inch) CNMG431 CNMG /2 3/16 CNMG432 CNMG /2 3/16 CNMG433 CNMG /2 3/16 R (Inch) / / /64 Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont - General Purpose Finish Turning SS T6020 TO-1271 $9.32 $7.25 Rough & Heavy Turning Finish Turning SS T6030 TO-1272 $9.32 $7.25 Cont - General Purpose Medium Turning SM T6020 TO-1267 $9.32 $7.25 Rough & Heavy Turning Medium Turning SM T6030 TO-1268 $9.32 $7.25 Cont - General Purpose Finish Turning SS T6020 TO-1340 $9.32 $7.25 Rough & Heavy Turning Finish Turning SS T6030 TO-1341 $9.32 $7.25 Cont - General Purpose Medium Turning SM T6020 TO-1336 $9.32 $7.25 Rough & Heavy Turning Medium Turning SM T6030 TO-1337 $9.32 $7.25 Rough & Heavy Turning Heavy Turning TH T6030 TO-1356 $9.32 $7.25 Rough & Heavy Turning Finish Turning SS T6030 TO-1417 $9.32 $7.25 Rough & Heavy Turning Medium Turning SM T6030 TO-1415 $9.32 $ Master Catalog 325 DEURRING

58 CHUCK JAWS LATHE WORKHOLDING CNMG 80 DIAMOND TURNING INSERTS CNMG INSERTS FOR SUPER ALLOYS 80 mond uy In ox Quantities & Save! MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS ANSI ISO IC (Inch) T (Inch) CNMG431 CNMG /2 3/16 CNMG432 CNMG /2 3/16 CNMG433 CNMG /2 3/16 R (Inch) / / /64 Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Finish Turning SA AH110 TO-1265 $9.32 $7.25 Cont & Int Turning Finish Turning SA AH120 TO-1266 $9.32 $7.25 Cont Medium Turning TM AH110 TO-1284 $9.32 $7.25 Cont & Int Turning Medium Turning TM AH120 TO-1285 $9.32 $7.25 Cont Finish Turning SA AH110 TO-1330 $9.32 $7.25 Cont & Int Turning Finish Turning SA AH120 TO-1331 $9.32 $7.25 Cont Medium Turning TM AH110 TO-1363 $9.32 $7.25 Cont & Int Turning Medium Turning TM AH120 TO-1364 $9.32 $7.25 Cont & Int Turning Heavy Turning TH AH120 TO-1352 $9.32 $7.25 Cont & Int Turning Medium Turning TM AH120 TO-1435 $9.32 $7.25 Cont & Int Turning Heavy Turning TH AH120 TO-1425 $9.32 $7.25 CNMG543 CNMG /8 1/ Cont & Int Turning Heavy Turning TH AH120 TO-1477 $14.81 $11.52 TOOLHOLDERS CNMG/CNGG INSERTS FOR ALUMINUM 80 mond uy In ox Quantities & Save! INDEXALE DRILLS TURNING & ORING ANSI ISO IC (Inch) T (Inch) CNMG431 CNMG /2 3/16 CNMG432 CNMG /2 3/16 CNMG433 CNMG /2 3/16 R (Inch) / / /64 Coating Cutting Conditions Chip reaker Grade 1-9 Pcs ox Tialn Coated Carbide Cont 28 AH110 TO-1302 $9.32 $7.25 Tialn Coated Carbide Cont & Int Turning 28 AH120 TO-1303 $9.32 $7.25 Tialn Coated Carbide Cont 28 AH110 TO-1381 $9.32 $7.25 Tialn Coated Carbide Cont & Int Turning 28 AH120 TO-1382 $9.32 $7.25 Tialn Coated Carbide Cont 28 AH110 TO-1434 $9.32 $7.25 ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD CNGG431 CNGG /2 3/16 CNGG432 CNGG /2 3/16 GRADES & CHIPREAKERS / /32 TUNGALOY CHIPREAKERS reaker TS TM TH SS SM SA P PM PP PS Operation Semi Finish Turning Medium Turning Heavy Turning Finish Turning Medium Turning Finish Turning Very sharp cutting edge Medium To Rough oring General Purpose oring Finish To Medium oring 28 General Turning Uncoated Carbide Cont LP TH10 TO-1205 $15.89 $12.36 Uncoated Carbide Cont LP TH10 TO-1208 $15.89 $12.36 TUNGALOY GRADES Master Catalog Grade Coating/ Carbide Or Cermet Cutting Conditions NS530 Uncoated Cermet Cont AT530 Tialn Coated Cermet Cont T9105 Ticn+al Oxide Coated Carbide Cont - High Speed Turning T9115 Ticn+al Oxide Coated Carbide Cont - General Purpose Turning T9125 Ticn+al Oxide Coated Carbide Cont & Int Turning T9135 Ticn+al Oxide Coated Carbide Severely Int & Heavy Cutting T6020 Ticn+al Oxide Coated Carbide Cont - General Purpose Turning T6030 Ticn+al Oxide Coated Carbide Rough & Heavy Turning T5020 Tin Coated Carbide Rough & Int Turning AH110 Tialn Coated Carbide Cont AH120 Tialn Coated Carbide Cont & Int Turning TH10 Uncoated Carbide Cont H10T Uncoated Carbide Cont

59 DNMG 55 DIAMOND TURNING INSERTS DNMG INSERTS FOR STEELS 55 mond uy In ox Quantities & Save! ANSI ISO IC (Inch) T (Inch) DNMG431 DNMG /2 3/16 DNMG432 DNMG /2 3/16 DNMG433 DNMG /2 3/16 R (Inch) / / /64 Cutting Conditions DNMG INSERTS FOR STAINLESS STEELS 55 mond ANSI ISO IC (Inch) T (Inch) DNMG431 DNMG /2 3/16 DNMG432 DNMG /2 3/16 R (Inch) / /32 Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Semi Finish Turning TS NS530 TO-1733 $9.14 $7.11 Cont Semi Finish Turning TS AT530 TO-1731 $11.93 $9.28 Cont - General Purpose Semi Finish Turning TS T9115 TO-3579 $12.42 $9.66 Cont & Int Turning Semi Finish Turning TS T9125 TO-3580 $12.42 $9.66 Cont - General Purpose Medium Turning TM T9115 TO-3576 $12.42 $9.66 Cont & Int Turning Medium Turning TM T9125 TO-3577 $12.42 $9.66 Severely Int & Heavy Cutting Medium Turning TM T9135 TO-3578 $12.42 $9.66 Cont Semi Finish Turning TS NS530 TO-1802 $9.14 $7.11 Cont Semi Finish Turning TS AT530 TO-1800 $11.93 $9.28 Cont - General Purpose Semi Finish Turning TS T9115 TO-3589 $12.42 $9.66 Cont & Int Turning Semi Finish Turning TS T9125 TO-3590 $12.42 $9.66 Cont - General Purpose Medium Turning TM T9115 TO-3586 $12.42 $9.66 Cont & Int Turning Medium Turning TM T9125 TO-3587 $12.42 $9.66 Cont & Int Turning Heavy Turning TH T9125 TO-3583 $12.42 $9.66 Cont & Int Turning Medium Turning TM T9125 TO-3595 $12.42 $9.66 Cont & Int Turning Heavy Turning TH T9125 TO-3592 $12.42 $9.66 Severely Int & Heavy Cutting Heavy Turning TH T9135 TO-3593 $12.42 $9.66 Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont - General Purpose Finish Turning SS T6020 TO-1695 $11.93 $9.28 Rough & Heavy Turning Finish Turning SS T6030 TO-1696 $11.93 $9.28 Cont - General Purpose Medium Turning SM T6020 TO-1691 $11.93 $9.28 Rough & Heavy Turning Medium Turning SM T6030 TO-1692 $11.93 $9.28 Cont - General Purpose Finish Turning SS T6020 TO-1753 $11.93 $9.28 Rough & Heavy Turning Finish Turning SS T6030 TO-1754 $11.93 $9.28 Cont - General Purpose Medium Turning SM T6020 TO-1749 $11.93 $9.28 Rough & Heavy Turning Medium Turning SM T6030 TO-1750 $11.93 $9.28 Rough & Heavy Turning Heavy Turning TH T6030 TO-1766 $11.93 $9.28 DNMG433 DNMG /2 3/ Rough & Heavy Turning Medium Turning SM T6030 TO-1817 $11.93 $9.28 DNMG INSERTS FOR SUPER ALLOYS 55 mond ANSI ISO IC (Inch) T (Inch) DNMG431 DNMG /2 3/16 DNMG432 DNMG /2 3/16 R (Inch) / /32 Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont & Int Turning Finish Turning SA AH120 TO-1690 $11.93 $9.28 Cont & Int Turning Medium Turning TM AH120 TO-1709 $11.93 $9.28 Cont & Int Turning Finish Turning SA AH120 TO-1747 $11.93 $9.28 Cont & Int Turning Medium Turning TM AH120 TO-1774 $11.93 $9.28 Cont & Int Turning Heavy Turning TH AH120 TO-1764 $11.93 $9.28 DNMG433 DNMG /2 3/ Cont & Int Turning Medium Turning TM AH120 TO-1834 $11.93 $9.28 DNMG/DNGG INSERTS FOR ALUMINUM 55 mond ANSI ISO IC (Inch) T (Inch) DNMG431 DNMG /2 3/16 DNMG432 DNMG /2 3/16 DNGG431 DNGG /2 3/16 R (Inch) / / /64 Coating uy In ox Quantities & Save! uy In ox Quantities & Save! uy In ox Quantities & Save! Cutting Conditions Chip reaker Grade 1-9 Pcs ox Tialn Coated Carbide Cont 28 AH110 TO-1726 $11.93 $9.28 Tialn Coated Carbide Cont & Int Turning 28 AH120 TO-1727 $11.93 $9.28 Tialn Coated Carbide Cont 28 AH110 TO-1791 $11.93 $9.28 Tialn Coated Carbide Cont & Int Turning 28 AH120 TO-1792 $11.93 $9.28 Uncoated Carbide Cont LP TH10 TO-1655 $13.77 $ Master Catalog 327 CARIDE INSERTS DEURRING

60 CHUCK JAWS LATHE WORKHOLDING TNMG 60 TRIANGLE TURNING INSERTS TNMG INSERTS FOR STEELS 60 Triangle uy In ox Quantities & Save! MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ANSI ISO IC (Inch) T (Inch) R (Inch) Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs TNMG331 TNMG /8 3/ Cont & Int Turning Medium Turning TM T9125 TO-3640 $7.07 $5.50 TNMG322 TNMG /8 1/ Cont & Int Turning Medium Turning TM T9125 TO-7455 $6.38 $4.96 TNMG332 TNMG /8 3/ /32 ox Cont & Int Turning Medium Turning TM T9125 TO-3645 $7.07 $5.50 Severely Int & Heavy Cutting Medium Turning TM T9135 TO-3646 $7.07 $5.50 TNMG333 TNMG /8 3/ Cont - General Purpose Medium Turning TM T9115 TO-7701 $7.07 $5.50 TNMG432 TNMG /2 3/16 TNMG433 TNMG /2 3/ / /64 TNMG INSERTS FOR STAINLESS STEELS 60 Triangle ANSI ISO IC (Inch) T (Inch) TNMG331 TNMG /8 3/16 TNMG332 TNMG /8 3/16 TNMG431 TNMG /2 3/16 Cont & Int Turning Medium Turning TM T9125 TO-3657 $10.17 $7.91 Severely Int & Heavy Cutting Medium Turning TM T9135 TO-3658 $10.17 $7.91 Cont - General Purpose Heavy Turning TH T9115 TO-3653 $10.17 $7.91 Cont & Int Turning Heavy Turning TH T9125 TO-3654 $10.17 $7.91 Severely Int & Heavy Cutting Heavy Turning TH T9135 TO-3655 $10.17 $7.91 Cont & Int Turning Medium Turning TM T9125 TO-3465 $10.17 $7.91 Severely Int & Heavy Cutting Medium Turning TM T9135 TO-3664 $10.17 $7.91 uy In ox Quantities & Save! R (Inch) / / /64 Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont - General Purpose Finish Turning SS T6020 TO-2703 $7.07 $5.50 Cont - General Purpose Medium Turning SM T6020 TO-2699 $7.07 $5.50 Rough & Heavy Turning Medium Turning SM T6030 TO-2700 $7.07 $5.50 Cont - General Purpose Medium Turning SM T6020 TO-2751 $7.07 $5.50 Rough & Heavy Turning Medium Turning SM T6030 TO-2752 $7.07 $5.50 Cont - General Purpose Finish Turning SS T6020 TO-2829 $10.17 $7.91 Rough & Heavy Turning Finish Turning SS T6030 TO-2830 $10.17 $7.91 TNMG432 TNMG /2 3/ Cont - General Purpose Finish Turning SS T6020 TO-2850 $10.17 $7.91 TNMG INSERTS FOR SUPER ALLOYS 60 Triangle uy In ox Quantities & Save! ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ANSI ISO IC (Inch) TUNGALOY CHIPREAKERS reaker TS TM TH T (Inch) TNMG331 TNMG /8 3/16 TNMG332 TNMG /8 3/16 TNMG431 TNMG /2 3/16 TNMG432 TNMG /2 3/16 R (Inch) / / / /32 Operation Semi Finish Turning Medium Turning Heavy Turning Cutting Conditions TUNGALOY GRADES Master Catalog Grade Operation/ Application Chip reaker Coating/ Carbide Or Cermet Grade 1-9 Pcs Cutting Conditions NS530 Uncoated Cermet Cont AT530 Tialn Coated Cermet Cont T9105 Ticn+al Oxide Coated Carbide Cont - High Speed Turning T9115 Ticn+al Oxide Coated Carbide Cont - General Purpose Turning T9125 Ticn+al Oxide Coated Carbide Cont & Int Turning ox Cont & Int Turning Finish Turning SA AH120 TO-2698 $7.07 $5.50 Cont & Int Turning Medium Turning TM AH120 TO-2716 $7.07 $5.50 Cont Medium Turning TM AH110 TO-2768 $7.07 $5.50 Cont & Int Turning Medium Turning TM AH120 TO-2769 $7.07 $5.50 Cont & Int Turning Medium Turning TM AH120 TO-2833 $10.17 $7.91 Cont & Int Turning Finish Turning SA AH120 TO-2844 $10.17 $7.91 Cont & Int Turning Medium Turning TM AH120 TO-2868 $10.17 $7.91 Cont & Int Turning Heavy Turning TH AH120 TO-2859 $10.17 $7.91 TNMG433 TNMG /2 3/ Cont & Int Turning Finish Turning SA AH120 TO-2888 $10.17 $7.91 TUNGALOY GRADES & CHIPREAKERS T9135 Ticn+al Oxide Coated Carbide Severely Int & Heavy Cutting

61 VNMG DIAMOND/SNMG SQUARE TURNING INSERTS VNMG INSERTS FOR STEELS 35 mond uy In ox Quantities & Save! ANSI ISO IC (Inch) T (Inch) VNMG331 VNMG /8 3/16 VNMG332 VNMG /8 3/16 R (Inch) / /32 Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Semi Finish Turning TS NS530 TO-3175 $8.91 $6.93 Cont Semi Finish Turning TS AT530 TO-3173 $11.66 $9.07 Cont & Int Turning Semi Finish Turning TS T9125 TO-3683 $12.11 $9.42 Cont - General Purpose Medium Turning TM T9115 TO-3679 $12.11 $9.42 Cont & Int Turning Medium Turning TM T9125 TO-3680 $12.11 $9.42 Severely Int & Heavy Cutting Medium Turning TM T9135 TO-3681 $12.11 $9.42 Cont Semi Finish Turning TS NS530 TO-3207 $8.91 $6.93 Cont Semi Finish Turning TS AT530 TO-3205 $11.66 $9.07 Cont & Int Turning Semi Finish Turning TS T9125 TO-3689 $12.11 $9.42 Cont - General Purpose Medium Turning TM T9115 TO-3685 $12.11 $9.42 Cont & Int Turning Medium Turning TM T9125 TO-3686 $12.11 $9.42 Severely Int & Heavy Cutting Medium Turning TM T9135 TO-3687 $12.11 $9.42 VNMG333 VNMG /8 3/ Cont & Int Turning Medium Turning TM T9125 TO-3691 $12.11 $9.42 VNMG INSERTS FOR STAINLESS STEELS 35 mond ANSI ISO IC (Inch) T (Inch) VNMG331 VNMG /8 3/16 VNMG332 VNMG /8 3/16 R (Inch) / /32 VNMG INSERTS FOR SUPER ALLOYS 35 mond ANSI ISO IC (Inch) T (Inch) VNMG331 VNMG /8 3/16 VNMG332 VNMG /8 3/16 uy In ox Quantities & Save! Cutting Conditions uy In ox Quantities & Save! R (Inch) / /32 SNMG INSERTS FOR SUPER ALLOYS 90 Square Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont - General Purpose Finish Turning SS T6020 TO-3154 $11.66 $9.07 Rough & Heavy Turning Finish Turning SS T6030 TO-3155 $11.66 $9.07 Cont - General Purpose Finish Turning SS T6020 TO-3184 $11.66 $9.07 Rough & Heavy Turning Finish Turning SS T6030 TO-3185 $11.66 $9.07 Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Medium Turning TM AH110 TO-3161 $11.66 $9.07 Cont & Int Turning Medium Turning TM AH120 TO-3162 $11.66 $9.07 Cont Medium Turning TM AH110 TO-3193 $11.66 $9.07 Cont & Int Turning Medium Turning TM AH120 TO-3194 $11.66 $9.07 uy In ox Quantities & Save! CARIDE INSERTS ANSI ISO IC (Inch) T (Inch) R (Inch) Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs SNMG431 SNMG /2 3/ Cont & Int Turning Medium Turning TM AH120 TO-2247 $8.96 $6.97 SNMG432 SNMG /2 3/16 SNMG433 SNMG /2 3/ / /64 ox Cont & Int Turning Finish Turning SA AH120 TO-2269 $8.96 $6.97 Cont & Int Turning Heavy Turning TH AH120 TO-2284 $8.96 $6.97 Cont & Int Turning Finish Turning SA AH120 TO-2313 $8.96 $6.97 Cont & Int Turning Heavy Turning TH AH120 TO-2323 $8.96 $6.97 SNMG543 SNMG /8 1/ Cont & Int Turning Heavy Turning TH AH120 TO-2349 $13.86 $ Master Catalog 329 DEURRING

62 CHUCK JAWS LATHE WORKHOLDING WNMG 80 TRIGON TURNING INSERTS WNMG INSERTS FOR STEELS 80 Trigon uy In ox Quantities & Save! MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS ANSI ISO IC (Inch) T (Inch) R (Inch) Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs WNMG331 WNMG /8 3/ Cont & Int Turning Medium Turning TM T9125 TO-3695 $6.71 $5.22 WNMG332 WNMG /8 3/ Cont & Int Turning Medium Turning TM T9125 TO-3698 $6.71 $5.22 WNMG431 WNMG /2 3/16 WNMG432 WNMG /2 3/16 WNMG433 WNMG /2 3/ / / /64 ox Cont Semi Finish Turning TS NS530 TO-3296 $6.80 $5.29 Cont Semi Finish Turning TS AT530 TO-3294 $9.32 $7.25 Cont - General Purpose Medium Turning TM T9115 TO-3699 $9.32 $7.25 Cont & Int Turning Medium Turning TM T9125 TO-3700 $9.32 $7.25 Cont Semi Finish Turning TS NS530 TO-3358 $6.80 $5.29 Cont & Int Turning Semi Finish Turning TS T9125 TO-3713 $9.32 $7.25 Cont - General Purpose Medium Turning TM T9115 TO-3709 $9.32 $7.25 Cont & Int Turning Medium Turning TM T9125 TO-3710 $9.32 $7.25 Severely Int & Heavy Cutting Medium Turning TM T9135 TO-3711 $9.32 $7.25 Cont - High Speed Turning Heavy Turning TH T9105 TO-3704 $9.32 $7.25 Cont & Int Turning Heavy Turning TH T9125 TO-3705 $9.32 $7.25 Severely Int & Heavy Cutting Heavy Turning TH T9135 TO-3707 $9.32 $7.25 Cont - General Purpose Medium Turning TM T9115 TO-3718 $9.32 $7.25 Cont & Int Turning Medium Turning TM T9125 TO-3719 $9.32 $7.25 Cont & Int Turning Heavy Turning TH T9125 TO-3715 $9.32 $7.25 WNMG434 WNMG /2 3/ Cont & Int Turning Medium Turning TM T9125 TO-3723 $9.32 $7.25 WNMG INSERTS FOR STAINLESS STEELS 80 Trigon uy In ox Quantities & Save! INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ANSI ISO IC (Inch) T (Inch) WNMG431 WNMG /2 3/16 WNMG432 WNMG /2 3/16 WNMG433 WNMG /2 3/16 R (Inch) / / /64 WNMG INSERTS FOR SUPER ALLOYS 80 Trigon Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont - General Purpose Finish Turning SS T6020 TO-3267 $9.32 $7.25 Rough & Heavy Turning Medium Turning SM T6030 TO-3263 $9.32 $7.25 Cont - General Purpose Finish Turning SS T6020 TO-3318 $9.32 $7.25 Cont - General Purpose Finish Turning SS T6020 TO-3319 $9.32 $7.25 Cont - General Purpose Medium Turning SM T6020 TO-3314 $9.32 $7.25 Rough & Heavy Turning Medium Turning SM T6030 TO-3315 $9.32 $7.25 Rough & Heavy Turning Heavy Turning TH T6030 TO-3332 $9.32 $7.25 Cont - General Purpose Medium Turning SM T6020 TO-3374 $9.32 $7.25 Rough & Heavy Turning Medium Turning SM T6030 TO-3375 $9.32 $7.25 uy In ox Quantities & Save! ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ANSI ISO IC (Inch) T (Inch) WNMG431 WNMG /2 3/16 WNMG432 WNMG /2 3/16 WNMG433 WNMG /2 3/16 R (Inch) / / /64 Cutting Conditions Operation/ Application Master Catalog Chip reaker Grade 1-9 Pcs ox Cont Medium Turning TM AH110 TO-3276 $9.32 $7.25 Cont & Int Turning Medium Turning TM AH120 TO-3277 $9.32 $7.25 Cont Finish Turning SA AH110 TO-3310 $9.32 $7.25 Cont & Int Turning Finish Turning SA AH120 TO-3311 $9.32 $7.25 Cont Medium Turning TM AH110 TO-3337 $9.32 $7.25 Cont & Int Turning Medium Turning TM AH120 TO-3338 $9.32 $7.25 Cont & Int Turning Heavy Turning TH AH120 TO-3329 $9.32 $7.25 Cont & Int Turning Medium Turning TM AH120 TO-3391 $9.32 $7.25 Cont & Int Turning Heavy Turning TH AH120 TO-3383 $9.32 $7.25

63 CCMT ORING INSERTS CCMT INSERTS FOR STEELS 80 mond, 7 Relief Angle uy In ox Quantities & Save! ANSI ISO IC (Inch) T (Inch) CCMT21.50 CCMT /4 3/32 CCMT21.51 CCMT /4 3/32 CCMT21.52 CCMT /4 3/32 CCMT32.50 CCMT09T302 3/8 5/32 CCMT32.51 CCMT09T304 3/8 5/32 CCMT32.52 CCMT09T308 3/8 5/32 R (Inch) / / / / / /32 Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Finish To Medium oring PS AT530 TO-1133 $7.20 $5.60 Cont & Int Turning Finish To Medium oring PS T9125 TO-3500 $7.52 $5.85 Cont Finish To Medium oring PS NS530 TO-1142 $5.18 $4.03 Cont Finish To Medium oring PS AT530 TO-1141 $7.20 $5.60 Cont & Int Turning Finish To Medium oring PS T9125 TO-3501 $7.52 $5.85 Cont Finish To Medium oring PS NS530 TO-1150 $5.18 $4.03 Cont Finish To Medium oring PS AT530 TO-1149 $7.20 $5.60 Cont & Int Turning Finish To Medium oring PS T9125 TO-3502 $7.52 $5.85 Cont Finish To Medium oring PS AT530 TO-1157 $8.91 $6.93 Cont & Int Turning Finish To Medium oring PS T9125 TO-3503 $7.92 $6.16 Cont Finish To Medium oring PS NS530 TO-1164 $6.12 $4.76 Cont Finish To Medium oring PS AT530 TO-1163 $8.91 $6.93 Cont & Int Turning Finish To Medium oring PS T9125 TO-3504 $7.92 $6.16 Cont Finish To Medium oring PS AT530 TO-1171 $8.91 $6.93 Cont & Int Turning Finish To Medium oring PS T9125 TO-3505 $7.92 $6.16 CCMT INSERTS FOR STAINLESS STEELS 55 mond uy In ox Quantities & Save! ANSI ISO IC (Inch) T (Inch) R (Inch) Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs CCMT CCMT /4 3/ Cont Finish To Medium PS AT530 TO-1133 $7.20 $5.60 Cont Finish To Medium PS NS530 TO-1142 $5.18 $4.03 Cont Finish To Medium PS AT530 TO-1141 $7.20 $5.60 CCMT21.51 CCMT /4 3/ Cont - General Purpose Finish PF T6020 TO-3802 $7.20 $5.60 1/64 Rough & Heavy oring Finish PF T6030 TO-3803 $7.20 $5.60 Cont - General Purpose Medium To Rough PM T6020 TO-3808 $7.20 $5.60 Rough & Heavy oring Medium To Rough PM T6030 TO-3809 $7.20 $5.60 Cont Finish To Medium PS NS530 TO-1150 $5.18 $4.03 CCMT21.52 CCMT /4 3/ Cont Finish To Medium PS AT530 TO-1149 $7.20 $5.60 1/32 Cont - General Purpose Medium To Rough PM T6020 TO-3819 $7.20 $5.60 Rough & Heavy oring Medium To Rough PM T6030 TO-3820 $7.20 $5.60 CCMT CCMT09T302 3/8 5/ Cont Finish To Medium PS AT530 TO-1157 $8.91 $6.93 1/256 Rough & Heavy oring Finish To Medium PS T6030 TO-3457 $8.91 $6.93 Cont Finish To Medium PS NS530 TO-1164 $6.12 $4.76 Cont Finish To Medium PS AT530 TO-1163 $8.91 $6.93 CCMT32.51 CCMT09T304 3/8 5/ Cont - General Purpose Finish PF T6020 TO-3825 $8.91 $6.93 1/64 Rough & Heavy oring Finish PF T6030 TO-3826 $8.91 $6.93 Cont - General Purpose Medium To Rough PM T6020 TO-3831 $8.91 $6.93 Rough & Heavy oring Medium To Rough PM T6030 TO-3832 $8.91 $6.93 Cont Finish To Medium PS AT530 TO-1171 $8.91 $6.93 Cont - General Purpose Finish PF T6020 TO-3836 $8.91 $6.93 CCMT32.52 CCMT09T308 3/8 5/ /32 Rough & Heavy oring Finish PF T6030 TO-3837 $8.91 $6.93 Cont - General Purpose Medium To Rough PM T6020 TO-3842 $8.91 $6.93 Rough & Heavy oring Medium To Rough PM T6030 TO-3843 $8.91 $6.93 DISPOSALE EARPLUGS NRR 31db CE EN-352-2:2002 certification Contoured fit, disposable polyurethane ear plugs Plug gently expands and selfadjusts to all size ear canals Available corded or uncorded in convenient dispenser box ox Description Pack Size Disposable Uncorded Earplugs 200/box PYR-DP1000 $25.00 Disposable Corded Earplugs 100/box PYR-DP1001 $ Master Catalog 331 CARIDE INSERTS DEURRING

64 CHUCK JAWS LATHE WORKHOLDING CCGT/CPMT ORING INSERTS CCGT INSERTS FOR NON-FERROUS METALS 80 mond, 7 Relief Angle uy In ox Quantities & Save! CCGT MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS ANSI ISO IC (Inch) T (Inch) CCGT CCGT /4 3/32 CCGT21.51 CCGT /4 3/32 CCGT CCGT09T302 3/8 5/32 CCGT32.51 CCGT09T304 3/8 5/32 CCGT32.52 CCGT09T308 3/8 5/32 CCGT430.5 CCGT /2 3/16 CPMT INSERTS FOR STEELS 80 mond, 11 Relief Angle R (Inch) / / / / / /256 Cutting Conditions Operation/ Application Chip reaker Grade uy In ox Quantities & Save! 1-9 Pcs ox Cont Non Ferrous oring PP H10T TO-1112 $10.40 $8.09 Cont Non Ferrous oring PP H10T TO-1114 $10.40 $8.09 Cont Non Ferrous oring PP H10T TO-1116 $11.79 $9.17 Cont Non Ferrous oring PP H10T TO-1117 $11.79 $9.17 Cont Non Ferrous oring PP H10T TO-1118 $11.79 $9.17 Cont Non Ferrous oring PP H10T TO-1119 $19.71 $15.33 TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ANSI ISO IC (Inch) T (Inch) CPMT CPMT /4 3/32 CPMT21.51 CPMT /4 3/32 CPMT CPMT09T302 3/8 5/32 CPMT32.51 CPMT09T304 3/8 5/32 CPMT32.52 CPMT09T308 3/8 5/32 R (Inch) / / / / /32 Cutting Conditions CPMT INSERTS FOR STAINLESS STEELS 80 mond, 11 Relief Angle Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Finish To Medium oring PS NS530 TO-1552 $4.73 $3.68 Cont Finish To Medium oring PS AT530 TO-1551 $7.20 $5.60 Cont & Int Turning Finish To Medium oring PS T9125 TO-3563 $7.52 $5.85 Cont Finish To Medium oring PS NS530 TO-1555 $4.73 $3.68 Cont Finish To Medium oring PS AT530 TO-1554 $7.20 $5.60 Cont & Int Turning Finish To Medium oring PS T9125 TO-3564 $7.52 $5.85 Cont Finish To Medium oring PS NS530 TO-1558 $6.34 $4.93 Cont Finish To Medium oring PS AT530 TO-1557 $7.61 $5.92 Cont Finish To Medium oring PS NS530 TO-1561 $6.34 $4.93 Cont Finish To Medium oring PS AT530 TO-1560 $7.61 $5.92 Cont Finish To Medium oring PS NS530 TO-1564 $6.34 $4.93 Cont Finish To Medium oring PS AT530 TO-1563 $7.61 $5.92 Cont & Int Turning Finish To Medium oring PS T9125 TO-3725 $7.92 $6.16 uy In ox Quantities & Save! ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ANSI ISO IC (Inch) T (Inch) CPMT CPMT /4 3/32 CPMT21.51 CPMT /4 3/32 CPMT CPMT09T302 3/8 5/32 CPMT32.51 CPMT09T304 3/8 5/32 CPMT32.52 CPMT09T308 3/8 5/32 R (Inch) /256 Cutting Conditions Operation/ Application Master Catalog / / / /32 Chip reaker Grade 1-9 Pcs ox Cont Finish To Medium PS NS530 TO-1552 $4.73 $3.68 Cont Finish To Medium PS AT530 TO-1551 $7.20 $5.60 Cont Finish To Medium PS NS530 TO-1555 $4.73 $3.68 Cont Finish To Medium PS AT530 TO-1554 $7.20 $5.60 Cont Finish To Medium PS NS530 TO-1558 $6.34 $4.93 Cont Finish To Medium PS AT530 TO-1557 $7.61 $5.92 Cont Finish To Medium PS NS530 TO-1561 $6.34 $4.93 Cont Finish To Medium PS AT530 TO-1560 $7.61 $5.92 Cont Finish To Medium PS NS530 TO-1564 $6.34 $4.93 Cont Finish To Medium PS AT530 TO-1563 $7.61 $5.92

65 DCMT/DCGT ORING INSERTS DCMT INSERTS FOR STEELS 55 mond, 7 Relief Angle uy In ox Quantities & Save! ANSI ISO IC (Inch) T (Inch) DCMT21.51 DCMT /4 3/32 DCMT21.52 DCMT /4 3/32 DCMT32.51 DCMT11T304 3/8 5/32 DCMT32.52 DCMT11T308 3/8 5/32 R (Inch) / / / /32 Cutting Conditions DCMT INSERTS FOR STAINLESS STEELS 55 mond, 7 Relief Angle Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont & Int Turning Medium To Rough oring PM T9125 TO-3854 $7.61 $5.92 Cont & Int Turning Medium To Rough oring PM T9125 TO-3863 $7.61 $5.92 Cont & Int Turning Medium To Rough oring PM T9125 TO-3875 $10.71 $8.33 Cont & Int Turning Medium To Rough oring PM T9125 TO-3886 $10.71 $8.33 uy In ox Quantities & Save! ANSI ISO IC (Inch) T (Inch) R (Inch) Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs DCMT21.51 DCMT /4 3/ Cont - General Purpose Medium To Rough PM T6020 TO-3852 $7.34 $5.71 DCMT21.52 DCMT /4 3/32 DCMT32.51 DCMT11T304 3/8 5/32 DCMT32.52 DCMT11T308 3/8 5/ / / /32 DCMT INSERTS FOR SUPER ALLOYS 55 mond, 7 Relief Angle ox Rough & Heavy oring Finish PF T6030 TO-3848 $7.34 $5.71 Rough & Heavy oring Medium To Rough PM T6030 TO-3853 $7.34 $5.71 Cont - General Purpose Finish PF T6020 TO-3867 $10.31 $8.02 Rough & Heavy oring Medium To Rough PM T6030 TO-3874 $10.31 $8.02 Cont - General Purpose Finish PF T6020 TO-3878 $10.31 $8.02 Rough & Heavy oring Medium To Rough PM T6030 TO-3885 $10.31 $8.02 uy In ox Quantities & Save! CARIDE INSERTS ANSI ISO IC (Inch) T (Inch) DCMT21.51 DCMT /4 3/32 DCMT32.51 DCMT11T304 3/8 5/32 DCMT32.52 DCMT11T308 3/8 5/32 R (Inch) / / /32 Cutting Conditions DCGT INSERTS FOR NON-FERROUS METALS 55 mond, 7 Relief Angle ANSI ISO IC (Inch) T (Inch) DCGT21.51 DCGT /4 3/32 DCGT DCGT11T302 3/8 5/32 DCGT32.51 DCGT11T304 3/8 5/32 DCGT32.52 DCGT11T308 3/8 5/32 R (Inch) / / / /32 Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont & Int Turning Medium To Rough oring PM AH120 TO-3851 $7.34 $5.71 Cont & Int Turning Medium To Rough oring PM AH120 TO-3871 $10.31 $8.02 Cont Medium To Rough oring PM AH110 TO-3881 $10.31 $8.02 Cont & Int Turning Medium To Rough oring PM AH120 TO-3882 $10.31 $8.02 Cutting Conditions uy In ox Quantities & Save! DCGT Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Non Ferrous oring PP H10T TO-1581 $10.62 $8.26 Cont Non Ferrous oring PP H10T TO-1583 $14.90 $11.59 Cont Non Ferrous oring PP H10T TO-1584 $14.90 $11.59 Cont Non Ferrous oring PP H10T TO-1585 $14.90 $ Master Catalog 333 DEURRING

66 CHUCK JAWS LATHE WORKHOLDING TCGT/TCMT/TPMT ORING INSERTS TCGT INSERTS FOR NON-FERROUS METALS 60 Triangle, 7 Relief Angle TCGT uy In ox Quantities & Save! MACHINE VISES ANSI ISO IC (Inch) T (Inch) TCMT INSERTS FOR STEELS 60 Triangle, 7 Relief Angle R (Inch) Cutting Conditions Operation/ Application Chip reaker Grade uy In ox Quantities & Save! 1-9 Pcs TCGT21.50 TCGT /4 3/ /256 Cont Non Ferrous oring PP H10T TO-2535 $8.10 $6.30 TCGT21.51 TCGT /4 3/ /64 Cont Non Ferrous oring PP H10T TO-2536 $8.10 $6.30 TCGT32.51 TCGT16T304 3/8 5/ /64 Cont Non Ferrous oring PP H10T TO-2538 $14.99 $11.66 ox RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS ANSI ISO IC (Inch) T (Inch) R (Inch) Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs TCMT21.50 TCMT /4 3/ Cont & Int Turning Finish To Medium oring PS T9125 TO-3630 $7.52 $5.85 TCMT21.51 TCMT /4 3/ /64 ox Cont Finish To Medium oring PS NS530 TO-2555 $4.82 $3.75 Cont Finish To Medium oring PS AT530 TO-2554 $6.71 $5.22 Cont & Int Turning Finish To Medium oring PS T9125 TO-3631 $7.52 $5.85 TCMT21.52 TCMT /4 3/ Cont & Int Turning Finish To Medium oring PS T9125 TO-3632 $7.52 $5.85 TCMT32.52 TCMT16T308 3/8 5/ /32 TCMT INSERTS FOR STAINLESS STEELS 60 Triangle, 7 Relief Angle Cont Finish To Medium oring PS NS530 TO-2578 $6.71 $5.22 Cont & Int Turning Finish To Medium oring PS T9125 TO-3634 $11.93 $9.28 uy In ox Quantities & Save! INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ANSI ISO IC (Inch) T (Inch) TCMT21.50 TCMT /4 3/32 TCMT21.51 TCMT /4 3/32 TCMT32.52 TCMT16T308 3/8 5/32 R (Inch) /256 Cutting Conditions Operation/ Application Master Catalog / /32 TPMT INSERTS FOR STAINLESS STEELS 60 Triangle, 11 Relief Angle ANSI ISO IC (Inch) T (Inch) TPMT21.50 TPMT /4 3/32 TPMT21.51 TPMT /4 3/32 TPMT21.52 TPMT /4 3/32 TPMT2.522 TPMT /4 3/32 TPMT32.51 TPMT16T304 3/8 5/32 TPMT32.52 TPMT16T308 3/8 5/32 R (Inch) Chip reaker Grade 1-9 Pcs ox Rough & Heavy oring Finish To Medium PS T6030 TO-7216 $6.71 $5.22 Cont Finish To Medium PS NS530 TO-2555 $4.82 $3.75 Cont Finish To Medium PS AT530 TO-2554 $6.71 $5.22 Rough & Heavy oring Finish To Medium PS T6030 TO-7223 $6.71 $5.22 Cont Finish To Medium PS NS530 TO-2578 $6.71 $5.22 Cutting Conditions Operation/ Application uy In ox Quantities & Save! Chip reaker Grade 1-9 Pcs ox Cont Finish To Medium oring PS AT530 TO-3046 $6.71 $5.22 1/256 Cont & Int Turning Finish To Medium oring PS T9125 TO-3670 $7.52 $5.85 Cont Finish To Medium PS AT530 TO-3052 $6.17 $ Cont Finish To Medium oring PS NS530 TO-3053 $4.28 $3.33 1/64 Cont Finish To Medium oring PS AT530 TO-3052 $6.17 $4.80 Cont & Int Turning Finish To Medium oring PS T9125 TO-3671 $7.52 $ Cont Finish To Medium oring PS AT530 TO-3059 $6.71 $5.22 1/32 Cont & Int Turning Finish To Medium oring PS T9125 TO-3672 $7.52 $ /32 Cont & Int Turning Finish To Medium oring PS T9125 TO-3673 $6.71 $ Cont Finish To Medium oring PS AT530 TO-3066 $9.45 $7.35 1/64 Cont & Int Turning Finish To Medium oring PS T9125 TO-3674 $11.93 $ Cont Finish To Medium oring PS AT530 TO-3073 $9.45 $7.35 1/32 Cont & Int Turning Finish To Medium oring PS T9125 TO-3675 $11.93 $9.28

67 VMT/VCGT ORING INSERTS VMT INSERTS FOR STAINLESS STEELS 35 mond, 5 Relief Angle uy In ox Quantities & Save! ANSI ISO IC (Inch) T (Inch) VMT220 VMT /4 1/8 VMT221 VMT /4 1/8 VMT222 VMT /4 1/8 VMT331 VMT /8 3/16 VMT332 VMT /8 3/16 R (Inch) / / / / /32 Cutting Conditions VCGT INSERTS FOR NON-FERROUS METALS 35 mond, 7 Relief Angle Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Finish To Medium oring PS AT530 TO-3122 $13.01 $10.12 Cont Finish To Medium oring PS AT530 TO-3123 $13.01 $10.12 Cont Finish To Medium oring PS AT530 TO-3124 $13.01 $10.12 Cont Finish To Medium oring PS AT530 TO-3125 $16.52 $12.85 Cont Finish To Medium oring PS AT530 TO-3127 $16.52 $12.85 uy In ox Quantities & Save! VCGT ANSI ISO IC (Inch) T (Inch) VCGT331 VCGT /8 3/16 VCGT332 VCGT /8 3/16 ISCAR TURNING INSERTS CNMG TNMG WNMG DNMG VNMG ISCAR CHIPREAKERS Chipbreaker Application TF Medium cutting Medium cutting - sharp and PP positive radial edge R (Inch) / /32 Iscar Reference Cutting Conditions Operation/ Application Chip reaker Grade 1-9 Pcs ox Cont Non Ferrous oring PP H10T TO-3129 $13.77 $10.71 Cont Non Ferrous oring PP H10T TO-3130 $13.77 $10.71 IC T Radius Grade IC-3028 Grade IC-907 Grade IC-9250 CNMG-431-PP 1/2 3/ CAR-501 CAR-502 CAR-503 $9.77 CNMG431-TF 1/2 3/ CAR-511 CAR-512 CAR-513 $9.77 CNMG-432-PP 1/2 3/ CAR-521 CAR-522 CAR-523 $9.77 CNMG-432-TF 1/2 3/ CAR-531 CAR-532 CAR-533 $9.77 DNMG-431-TF 1/2 3/ CAR-541 CAR-542 CAR-543 $13.21 DNMG-432-PP 1/2 3/ CAR-551 CAR-552 CAR-553 $13.21 DNMG-432-TF 1/2 3/ CAR-561 CAR-562 CAR-563 $13.21 TNMG-331-PP 3/8 3/ CAR-571 CAR-572 CAR-573 $7.60 TNMG-331-TF 3/8 3/ CAR-582 CAR-583 $7.60 TNMG-332-PP 3/8 3/ CAR-592 CAR-593 $7.60 TNMG-332-TF 3/8 3/ CAR-601 CAR-602 CAR-603 $7.60 WNMG-431-PP 1/2 3/ CAR-611 CAR-612 CAR-613 $10.28 WNMG-431-TF 1/2 3/ CAR-621 CAR-622 CAR-623 $10.28 WNMG-432-PP 1/2 3/ CAR-631 CAR-632 CAR-633 $10.28 WNMG-432-TF 1/2 3/ CAR-641 CAR-642 CAR-643 $10.28 ISCAR GRADES GRADE ANSI CHART IC3028 CVD COATED IC907 PVD COATED IC9250 CVD COATING C3, C6-C7 C8-C7 C6-C5 WORKPIECE MATERIAL Carbon steel. Tool steel. Alloy steel. Stainless steel. Steel casting. Grey cast iron. High Temp Alloy, Austenitic Stainless Steels, Hard alloys. Wide range of steels and stainless steels. Specially for machining roughed low carbon and low alloy steels. Iscar RECOMMENDED APPLICATIONS Finishing.Medium.High wear resistance. High speed Medium feed. Low to medium speed, interrupted cutting Roughing and semi finishing, medium speed.suitable for unstable conditions Master Catalog 335 CARIDE INSERTS DEURRING

68 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD CARIDE TURNING INSERTS NEGATIVE TURNING INSERTS PALIT is a respected brand and global supplier of high qualitytungsten carbide tooling. Their products are recognized as technologically advanced, incorporating years of knowledge and expertise on highly complex metallurgy and materials science in tungsten carbide powders, high-speed steels, ceramics, diamond and other materials that are particularly resistant to heat, abrasion, pressure and wear. PALIT offers an extensive range of solutions for the metalworking industry and produces tungsten carbide inserts and tool holders for turning, milling, threading, drilling for most common metal cutting applications. Please call for more information. TURNING CHIPREAKERS Application P Steel GRADE INFORMATION M Stainless Grade ISO Range Coating Description PH2115 P20/M15/K20 CVD PH2125 P25/M25/K25 CVD PH2135 P35/M35/K35 CVD PH3215 M10-M20/P20 CVD PH3225 P25/M25-M35 CVD PH3235 M35/P30-P40 CVD PH6215 M10-M20/P20 PVD PH6225 M20-M30/P25 PVD PH6920 K25-K35 PVD K Cast Iron S Hi-Temp Alloys Semi-Finishing MF MF ST MS MR SS ST/FLAT MS Roughing MW MW MW MS Heavy Roughing HR HR HR SS NEW ITEM! HR Chipbreaker Ideal for heavy roughing of steels, stainless steel and cast iron MR Chipbreaker Ideal for roughing of steels OVERVIEW OF TURNING GRADES P M K S Application Steel Stainless Cast Iron Hi-Temp Alloys PVD CVD PVD CVD PVD CVD PVD Semi-Finishing PH6215 PH2115 PH6215 PH3215 PH6705 PH2705 PH6920 Roughing PH6225 PH2125 PH6920 PH3225 PH6315 PH2320 PH6920 Heavy Roughing PH6740 PH2135 PH6740 PH3235 PH6740 PH2115 PH6920 Coated Carbide grade for finishing to light roughing of Steel and Steel castings at high cutting speeds in wet and dry applications (AL203) Coated Carbide grade for finishing to roughing of Steel and Steel castings. A tough substrate optimized with a thick wear resistant coating. This grade can be applied in continuous cutting and interrupted cutting as well (AL203) Coated Carbide grade for roughing applications on Steel and Steel castings. A tough substrate for more strength and has a thick wear resistant coating. This grade is first option when the application requires an excellent security edge on high metal removal rates (AL203) Coated Carbide grade for finishing to semi-finishing operations on Stainless Steel. An excellent substrate to handle high temperatures,combined with a wear resistant coating make this grade our first option for continuous cutting and can be also applied at high speeds (TiC/TiN/TiCn) This grade has wide range of applications on Stainless Steel from semi-finishing to roughing operations. This grade was designed to be applied with excellent results on austenitic stainless and duplex Stainless Steel at moderate cutting speeds (TiC/TiN/TiCn) This grade is designed to respond on applications requiring good wear resistance at high to moderate speeds on Stainless Steel.The substrate promotes an excellent security on the cutting edge when applied on interrupted cuts (TiC/TiN/TiCn) ATiAlN coating with a hard substrate to prevent plastic deformation makes this grade one of our best options to machine Ni, Co based heat resistant Alloys (TiALN) Recommended for heat resistant super Alloys at low speeds or light interrupted cutting. Good resistance to thermal and mechanical shock makes this grade one of the best options to heavy machining operations (TiALN) Coated micro-grain Carbide grade. Recommended for heat resistant super Alloys and Titanium Alloys at low speeds. Excellent reduction of thermal shock and notch wear makes it suitable for long cuts or interrupted cuts (TiALN) Master Catalog MF Chipbreaker Ideal for semi-finishing of steels and stainless steels SS Chipbreaker Ideal for roughing of stainless and heavy roughing of high-temp alloys

69 CARIDE TURNING INSERTS NEGATIVE TURNING INSERTS NEW ITEM! CNMG DNMG TNMG VNMG Turning Inserts for Steel ANSI Radius Operation CNMG CNMG Cut Type Depth of Cut (in.) Speed (SFM) Feed (ipr) Coating Grade Ea 1-9 Pcs Ea ox Qty Finishing Continuous CVD MF PH2115 PL $8.10 $5.85 Finishing Interrupted CVD MF PH2125 PL $8.10 $5.85 Med/Heavy Cutting Interrupted CVD MR PH2135 PL $8.10 $5.85 Medium Cutting Continuous CVD MR PH2125 PL $8.10 $5.85 Finishing Continuous CVD MR PH2115 PL $8.10 $5.85 Medium Cutting Interrupted CVD HR PH2135 PL $8.10 $5.85 Finish/Med Cutting Cont/Int CVD MR PH2125 PL $8.10 $5.85 DNMG Finish/Heavy Cutting Cont/Int PVD MR PH6215 PL $13.28 $9.59 TNMG TNMG VNMG Turning Inserts for Stainless Steel ANSI Radius Operation CNMG CNMG Finishing Continuous CVD MF PH2115 PL $9.45 $6.83 Finish/Med Cutting Interrupted CVD MF PH2125 PL $9.45 $6.83 Medium Cutting Continuous PVD MF PH6225 PL $10.58 $7.64 Heavy Cutting Interrupted CVD MR PH2125 PL $9.45 $6.83 Heavy Cutting Continuous PVD MR PH6225 PL $10.58 $7.64 Finishing Interrupted CVD MR PH2135 PL $9.45 $6.83 Finishing Continuous CVD MR PH2115 PL $9.45 $6.83 Medium Cutting Cont/Int PVD HR PH6215 PL $10.58 $7.64 Heavy Cutting Cont/Int CVD HR PH2125 PL $9.45 $6.83 Finish/Heavy Cutting Continuous CVD MR PH2115 PL $11.25 $8.13 Finish/Heavy Cutting Interrupted CVD MR PH2125 PL $11.25 $8.13 Cut Type Depth of Cut (in.) Speed (SFM) Feed (ipr) Coating Grade Ea 1-9 Pcs Ea ox Qty Finishing Cont/Int PVD SS PH6920 PL $8.33 $6.01 Heavy Cutting Continuous CVD SS PH3225 PL $8.10 $5.85 Heavy Cutting Interrupted PVD SS PH6920 PL $8.33 $6.01 Finish/Heavy Cutting Cont/Int CVD SS PH3225 PL $8.10 $5.85 DNMG Finish/Heavy Cutting Cont/Int PVD SS PH6920 PL $13.28 $9.59 TNMG TNMG VNMG Finishing Continuous PVD SS PH6920 PL $10.58 $7.64 Finish/Med Cutting Interrupted CVD SS PH3225 PL $9.45 $6.83 Heavy Cutting Interrupted CVD SS PH3235 PL $9.45 $6.83 Heavy Cutting Continuous PVD SS PH6225 PL $10.58 $7.64 Medium Cutting Continuous PVD MF PH6225 PL $10.58 $7.64 Medium Cutting Cont/Int CVD HR PH3215 PL $9.45 $6.83 Finishing Interrupted CVD MR PH3235 PL $9.45 $6.83 Heavy Cutting Cont/Int CVD HR PH3225 PL $9.45 $6.83 Finishing Continuous CVD MR PH3225 PL $9.45 $6.83 Finish/Heavy Cutting Continuous PVD SS PH6920 PL $12.60 $9.10 Finish/Heavy Cutting Interrupted PVD MR PH6225 PL $12.60 $9.10 Turning Inserts for High Temp/Super Alloys ANSI Radius Operation CNMG CNMG Cut Type Depth of Cut (in.) Speed (SFM) Feed (ipr) Coating Chipbreaker Chipbreaker Chipbreaker Grade Ea 1-9 Pcs Ea ox Qty Finishing Cont/Int PVD MF PH6215 PL $8.33 $6.01 Med/Heavy Cutting Cont/Int PVD SS PH6215 PL $8.33 $6.01 Finishing Cont/Int PVD SS PH6920 PL $8.33 $6.01 Heavy Cutting Cont/Int PVD SS PH6225 PL $8.33 $6.01 DNMG Heavy Cutting Cont/Int PVD SS PH6920 PL $13.28 $9.59 TNMG TNMG Finishing Continuous PVD MF PH6215 PL $10.58 $7.64 Finishing Interrupted PVD MF PH6225 PL $10.58 $7.64 Med/Heavy Cutting Cont/Int PVD SS PH6920 PL $10.58 $7.64 Finishing Cont/Int PVD MF PH6215 PL $10.58 $7.64 Medium Cutting Cont/Int PVD SS PH6215 PL $10.58 $7.64 Heavy Cutting Cont/Int PVD SS PH6225 PL $10.58 $7.64 Additional Geometries & Grades Available! Please Call For More Information! Master Catalog 337 CARIDE INSERTS DEURRING

70 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD TURNING/ORING INSERTS FOR ALUMINUM KORLOY INSERTS For Machining Aluminum Grade H01-Uncoated grade for aluminum Sharp positive HA chipbreaker is ideal for aluminum For continuous non ferrous turning Designation METRIC CCGT DCGT SCGT TCGT VCGT Designation INCH CNMG Inserts with HA Chipbreaker Grade H01 IC Thickness Radius Grade Description CCGT Inserts 1/4 3/32 3/8 5/32 1/2 3/16 DCGT Inserts 1/4 3/32 3/8 5/32 SCGT Inserts 3/8 5/32 1/2 3/16 TCGT Inserts 1/4 3/32 3/8 5/32 VCGT Inserts 1/4 1/8 3/8 3/16 I.C Thickness Radius Master Catalog CNMG CNMG431 1/2 3/ (1/64) KOY-2144 $6.29 CNMG CNMG432 1/2 3/ (1/32) KOY-2145 $6.29 DNMG Inserts with HA Chipbreaker Grade H01 DNMG DNMG431 1/2 3/ (1/64) KOY-2141 $7.66 DNMG DNMG432 1/2 3/ (1/32) KOY-2146 $7.66 VNMG Inserts with HA Chipbreaker Grade H01 VNMG VNMG331 3/8 3/ (1/64) KOY-2142 $7.92 VNMG VNMG332 3/8 3/ (1/32) KOY-2149 $7.92 WNMG Inserts with HA Chipbreaker Grade H01 WNMG WNMG431 1/2 3/ (1/64) KOY-2143 $6.07 WNMG WNMG432 1/2 3/ (1/32) KOY-2147 $ H01 CCGT AK H01 KOY-1024 $7.87 1/64 H01 CCGT AK H01 KOY-1026 $ H01 CCGT AK H01 KOY-1028 $9.22 1/64 H01 CCGT AK H01 KOY-1030 $9.22 1/32 H01 CCGT AK H01 KOY-1032 $9.22 1/64 H01 CCGT 431 AK H01 KOY-1034 $ /32 H01 CCGT 432 AK H01 KOY-1036 $ H01 DCGT AK H01 KOY-1199 $7.87 1/64 H01 DCGT AK H01 KOY-1201 $ H01 DCGT AK H01 KOY-1203 $9.22 1/64 H01 DCGT AK H01 KOY-1205 $9.22 1/32 H01 DCGT AK H01 KOY-1207 $ H01 SCGT AK H01 KOY-1304 $9.62 1/64 H01 SCGT AK H01 KOY-1305 $9.62 1/32 H01 SCGT AK H01 KOY-1307 $9.62 1/64 H01 SCGT 431 AK H01 KOY-1308 $ /32 H01 SCGT 432 AK H01 KOY-1309 $ H01 TCGT AK H01 KOY-1456 $8.02 1/64 H01 TCGT AK H01 KOY-1458 $8.02 1/32 H01 TCGT AK H01 KOY-1460 $ H01 TCGT AK H01 KOY-1462 $ /64 H01 TCGT AK H01 KOY-1464 $ /32 H01 TCGT AK H01 KOY-1466 $ H01 VCGT AK H01 KOY-1632 $9.67 1/64 H01 VCGT 221 AK H01 KOY-1634 $9.67 1/32 H01 VCGT 222 AK H01 KOY-1636 $ H01 VCGT AK H01 KOY-1638 $ /64 H01 VCGT 331 AK H01 KOY-1640 $ /32 H01 VCGT 332 AK H01 KOY-1642 $11.04

71 TOOL ITS/CUT-OFF LADES SQUARE TOOL ITS High Speed Steel or Cobalt NEW ITEM! Applications: HSS is ideal for mild steel, alloys and tool steels-makes a superior finishing tool COALT performs well where high heat is present-used for heavy cuts in hard materials REGULAR LENGTH HSS M42 8% Cobalt Square Size CUT-OFF TOOL KITS kit consists of a tool block, a blade and either 10 N52 or PV52 carbide inserts. A New-Grip wrench is also included for removing inserts from the blade and an Allen wrench for positioning and removing the blade from the block. 1/8 2-1/2 A $1.15 A $2.97 3/16 2-1/2 A $1.15 A $2.97 1/4 2-1/2 A $1.68 A $3.14 5/16 2-1/2 A $2.17 A $4.40 3/8 3 A $3.66 A $7.66 7/16 3-1/2 A $5.21 A $9.90 1/2 4 A $7.10 A $ /8 4-1/2 A $11.98 A $ /4 5 A $19.50 A $ A $42.24 A $90.28 EXTRA LONG LENGTH HSS M35 5% COALT Square Size 1/4 4 A $1.90 A $3.50 1/4 6 A $3.40 A $6.20 1/4 8 A $4.50 A $8.68 5/16 6 A $4.49 A $7.59 3/8 4 A $4.65 A $7.92 3/8 6 A $6.47 A $8.97 3/8 8 A $8.80 A $ /2 6 A $10.30 A $20.43 ROUND TOOL ITS High Speed Steel NEW ITEM! Size 1/8 x 2-3/4 A $1.19 3/16 x 3-1/2 A $1.39 1/4 x 4 A $1.99 3/8 x 5 A $3.30 1/2 x 6 A $9.99 #2 New-Grip Starter Kit 1 ea NGTN-16-5 (5/8 ) lock 1 ea NGIH-26-2 lade 10 ea NGTN-2-N52 Inserts 1ea New-Grip Wrench 1 ea Allen Wrench # NEW-KIT2 $ #3 New-Grip Starter Kit 1 ea NGTN-19-5 (3/4 ) lock 1 ea NGIH-26-3 lade 10 ea NGTN-3-N52 Inserts 1ea New-Grip Wrench 1 ea Allen Wrench # NEW-KIT3 $ RECTANGULAR TOOL ITS High Speed Steel NEW ITEM! Size H x W CUT-OFF LADES Carbide Tipped Double ended for double performance Hardened and precision ground steel blades Tips are hollow ground all over for longer tool life T styled over entire blade length to fit all T type holders Also available with V-groove Width Height Applications: HSS is ideal for mild steel, alloys and tool steels-makes a superior finishing tool Standard With V-Groove 1/16 MI-T100 $47.90 MI-T100V $ /64 MI-T101 $47.90 MI-T101V $ /2 4-1/2 3/32 MI-T102 $46.10 MI-T102V $ /8 MI-T103 $46.10 MI-T103V $ /32 MI-T104 MI-T104V 1/8 MI-T105 MI-T105V 11/16 5 $ /32 MI-T106 MI-T106V $ /16 MI-T107 MI-T107V 1/8 MI-T108 MI-T108V 5/32 3/4 5 MI-T109 $55.65 MI-T109V $ /16 MI-T110 MI-T110V 1/8 MI-T111 MI-T111V 5/32 7/8 6 MI-T112 $55.65 MI-T112V $ /16 MI-T113 MI-T113V #4 New-Grip Starter Kit 1 ea NGTN-16-5 (5/8 ) lock 1 ea NGIH-26-3-PS lade 10 ea NGTN-3-PV52 Inserts 1ea New-Grip Wrench 1 ea Allen Wrench # NEW-KIT4 $ #5 New-Grip Starter Kit 1 ea NGTN-25-6 (1 ) lock 1 ea NGIH-32-3-PS lade 10 ea NGTN-3-PV52 Inserts 1ea New-Grip Wrench 1 ea Allen Wrench # NEW-KIT5 $ #6 New-Grip Starter Kit 1 ea NGTN-19-6 (3/4 ) lock 1 ea NGIH-32-3-PS lade 10 ea NGTN-3-PV52 Inserts 1ea New-Grip Wrench 1 ea Allen Wrench # NEW-KIT6 $ Master Catalog 339 1/4 x 3/8 3 A $2.63 1/4 x 1/2 4 A $4.19 1/4 x 3/4 5 A $8.37 3/8 x 3/4 5 A $ /8 x 1-1/4 6 A $ /2 x 3/4 5 A $ /2 x 1-1/2 7 A $ /8 x 1-1/2 7 A $ /4 x 1-1/2 7 A $45.09 C CARIDE INSERTS DEURRING

72 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD TOOL LOCKS FOR PART-OFF LADES CUT-OFF TOOL LOCKS Slot Grip block toolholders are designed to hold Slot Grip and competitive cut-off blades firm and secure using a wedge locking system. Center height of the cutting edge and shank height are equal to allow easy set-up. lock toolholders are available in a wide range of sizes and are available in either a two piece design for versatility or one piece design for economy. For manual lathes For CNC turning centers Wedge locking system lade and Inserts Sold Separately CUT-OFF TOOL LOCKS Compatible with blades from Dorian, Newcomer and other industry standard _GIH type blades Please see following page for blades and inserts NEUTRAL TOOLHOLDER SET Cut-Off and Grooving A D C Sets Includes lade, lock & 10 Inserts! Master Catalog L NGTN A C D L Use lade 5/8 1-3/16 1-1/64 5/8 3-7/16 _GIH 19-2 NGTN-16-2 $ /8 1-1/2 1-5/16 5/8 3-7/16 _GIH 26-2,3,4,5,6 NGTN-16-5 $ /4 1-1/2 1-7/16 3/4 3-7/16 _GIH 26-2,3,4,5,6 NGTN-19-5 $ /8 1-15/32 25/32 4-5/16 _GIH 32-3,4,5,6 NGTN-25-6 $ /4 1-7/8 1-13/16 1-1/8 4-5/16 _GIH 32-3,4,5,6,R/L-9 NGTN-32-6 $ /2 1-7/8 2-27/64 1-5/8 4-5/16 _GIH 32-9 NGTN-38-6 $ NGTR/L Dorian Slot Grip lades hold inserts securely by a tapered locking system. The blade and insert geometry permits free chip flow, minimizing insert breakage due to chip build-up. The toolholder features a two piece clamp style, providing for precise and rigid blade locking and easy mounting into CNC turrets. Inserts feature a controlled, coiled chip flow and higher material removal rates. Description H H1 1 L INCH A C D L Use lade 1 3/4 3/4 43/64 3-7/16 _GIH /4 25/ /32 4-3/4 _GIH 26-2,3,4,5,6 D Right Hand C Right or Left Right NGTR-19-2 $59.38 Left NGTL-19-2 $59.38 Right NGTR-25-6 $70.54 Left NGTL-25-6 $70.54 Description SGTN12, DN62970 $ SGTN DN62971 $ Left Hand lade Insert SGTN-3TIN Inserts, 1 SGIH26-3 lade, 1 SGTN 19-5 lock 10 SGTN-3TIN Inserts, 1 SGIH32-3 lade, 1 SGTN 25,4-6 lock lade Used _GIH19-2 SGTN DN62972 $ _GIH26-2 SGTN DN62973 $ Thru SGIH26-6 SGTN DN62974 $ SGTN25, DN62975 $ SGTN31, DN62976 $ SGTN38, DN62977 $ METRIC _GIH32-3 Thru SGIH32-9 SGTN ,0 34,9 12,7 25,4 76,20 DN62978 $ _GIH32-3 SGTN ,0 34,9 15,9 25,4 76,20 DN62971 $ Thru SGIH32-9 SGTN ,0 44,5 15,9 31,8 88,90 DN62972 $ _GIH26-2 SGTN ,0 50,8 19,1 34,9 88,90 DN62979 $ Thru SGIH26-6 SGTN ,0 50,8 19,1 34,9 114,3 DN62980 $ SGTN ,0 54,0 22,2 38,1 114,3 DN62981 $ SGTN ,0 60,3 28,6 44,5 114,3 DN62982 $ SGTN ,0 73,0 41,3 57,2 114,3 DN62983 $ _GIH32-3 Thru SGIH32-9 L Screw Used Per Set DN85326 $ DN85330 $ A x 1.0 A /4-20 x 1-1/4 A /4-20 x 1-1/2 A /4-20 x 1-1/2 A /4-20 x 1-1/4 A /4-20 x 1-1/2 A

73 PART-OFF INSERTS & LADES CUT-OFF (PART-OFF) LADES Dorian and Newcomer lades and Inserts are interchangeable with Iscar _GTN type holders. NS is the original Iscar design of blades, while PS is the newer Iscar design. Inserts interchangeable with other industry standard blades W H C A Insert L NS 7 Inserts Insert L PS Industry Standard Positive Stop lade Dorian Max work each Positive Stop lade Max Work Newcomer each Neutral Stop lade Max Work each Insert Reference W Inches W mm A L H H1 _GIH19-2 DN $57.73 NGIH-19-2-PS 1.5 $53.52 NGIH-19-2-NS 1-1/2 $39.29 _GT(N/R/L) _GIH26-2 DN $68.76 NGIH-26-2-PS 3 $53.52 NGIH-26-2-NS 2 $45.02 _GT(N/R/L) _GIH26-3 DN $68.76 NGIH-26-3-PS 3 $53.52 NGIH-26-3-NS 3 $45.02 _GT(N/R/L) _GIH26-4 DN $68.76 NGIH-26-4-PS 3 $55.70 NGIH-26-4-NS 3 $47.21 _GT(N/R/L) _GIH26-5 DN $68.76 NGIH-26-5-PS 3 $60.07 NGIH-26-5-NS 4 $50.77 _GT(N/R/L) _GIH26-6 DN $68.76 NGIH-26-6-PS 3 $62.24 NGIH-26-6-NS 4 $50.77 _GT(N/R/L) _GIH32-3 DN $79.54 NGIH-32-3-PS 4 $55.70 NGIH-32-3-NS 4 $47.16 _GT(N/R/L) _GIH32-4 DN $79.54 NGIH-32-4-PS 4 $57.89 NGIH-32-4-NS 4 $48.28 _GT(N/R/L) _GIH32-5 DN $79.54 NGIH-32-5-PS 5 $62.24 NGIH-32-5-NS 5 $53.89 _GT(N/R/L) _GIH32-6 DN $79.54 NGIH-32-6-PS 5 $64.44 NGIH-32-6-NS 5 $55.08 _GT(N/R/L) _GIH32-8 DN $ NGIH-32-8-PS 5 $76.03 NGIH-32-8-NS 5 $51.16 _GT(N/R/L) _GIH32-9 DN $ NGIH-32-9-PS 5 $87.31 NGIH-32-9-NS 6 $76.40 _GT(N/R/L) CUT-OFF INSERTS Insert Ref# Insert Size W width ±.004 W width mm. L Lead Angle UnCoated C2 each Newcomer Inserts Uncoated C5 each Dorian Tools Inserts Coated C5 each Uncoated C2 each Uncoated C5 _GTN mm 0 CI-201 $5.67 CI-301 $6.24 CI-401 $8.09 DN82220 $7.03 DN82221 $7.03 DN82222 $9.59 _GTR mm 8 CI-204 $6.53 CI-304 $7.20 CI-404 $8.90 DN82248 $7.03 DN82249 $7.03 DN82250 $9.59 _GTL mm 8 CI-205 $6.53 CI-305 $7.20 CI-405 $8.90 DN82276 $7.03 DN82277 $7.03 DN82278 $9.59 _GTN mm 0 CI-208 $5.67 CI-308 $6.24 CI-408 $ _GTR mm 8 CI-211 $6.53 CI-311 $7.20 CI-411 $ _GTL mm 8 CI-212 $6.53 CI-312 $7.20 CI-412 $ _GTN mm 0 CI-215 $5.67 CI-315 $6.24 CI-415 $8.09 DN82224 $7.03 DN82225 $7.03 DN82226 $9.59 _GTR mm 8 CI-218 $6.53 CI-318 $7.20 CI-418 $8.90 DN82252 $7.03 DN82253 $7.03 DN82254 $9.59 _GTL mm 8 CI-219 $6.53 CI-319 $7.20 CI-419 $8.90 DN82280 $7.03 DN82281 $7.03 DN82282 $9.59 _GTN mm 0 CI-222 $6.77 CI-322 $7.47 CI-422 $9.18 DN82228 $7.74 DN82229 $7.74 DN82230 $9.90 _GTR mm 8 CI-225 $7.59 CI-325 $8.36 CI-425 $10.19 DN82256 $7.74 DN82257 $7.74 DN82258 $9.90 _GTL mm 8 CI-226 $7.59 CI-326 $8.36 CI-426 $10.19 DN82284 $7.74 DN82285 $7.74 DN82286 $9.90 _GTN mm 0 CI-229 $7.59 CI-329 $8.31 CI-429 $ _GTR mm 8 CI-232 $8.29 CI-332 $9.13 CI-432 $ _GTL mm 8 CI-233 $8.29 CI-333 $9.13 CI-433 $ _GTN mm 0 CI-238 $8.29 CI-338 $8.31 CI-438 $9.72 DN82232 $8.47 DN82233 $8.47 DN82234 $9.91 _GTR mm 8 CI-239 $8.29 CI-339 $9.13 CI-439 $10.59 DN82260 $8.47 DN82261 $8.47 DN82262 $9.91 _GTL mm 8 CI-240 $8.29 CI-340 $9.13 CI-440 $10.59 DN82288 $8.47 DN82289 $8.47 DN82290 $9.91 _GTN mm 0 CI-243 $8.65 CI-343 $9.53 CI-443 $11.20 DN82236 $9.34 DN82237 $9.34 DN82238 $12.54 _GTR mm 8 CI-246 $9.44 CI-346 $10.41 CI-446 $12.07 DN82264 $9.34 DN82265 $9.34 DN82266 $12.54 _GTL mm 8 CI-247 $9.44 CI-347 $10.41 CI-447 $12.07 DN82292 $9.34 DN82293 $9.34 DN82294 $12.54 _GTN mm 0 CI-250 $12.36 CI-350 $13.60 CI-450 $15.71 DN82240 $14.67 DN82241 $14.67 DN82242 $18.57 _GTR mm 4 CI-251 $13.21 CI-351 $14.54 CI-451 $16.59 DN82268 $14.67 DN82269 $14.67 DN82270 $18.57 _GTL mm 4 CI-252 $13.21 CI-352 $14.54 CI-452 $16.59 DN82296 $14.67 DN82297 $14.67 DN82298 $18.57 _GTN mm 0 CI-257 $16.15 CI-357 $17.79 CI-457 $20.20 DN82244 $16.68 DN82245 $16.68 DN82246 $19.24 _GTR mm 4 CI-258 $16.99 CI-358 $18.74 CI-458 $21.12 DN82272 $16.68 DN82273 $16.68 DN82274 $19.24 _GTL mm 4 CI-259 $16.99 CI-359 $18.69 CI-459 $21.12 DN82300 $16.68 DN82301 $16.68 DN82302 $19.24 each Coated C5-C6 each Master Catalog 341 CARIDE INSERTS DEURRING

74 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD EXTERNAL GROOVING & PART-OFF TOOLS EXTERNAL GROOVING TOOLHOLDERS Mono lock Type Mono block style toolholder offers high rigidity Multi-functional! Groove and turn with the same holder Available in right and left hand (right hand shown When depth is deeper than insert length, 1 corner type is recommended Max dimensions (Inch) Tungaloy Ref # Groove Depth (ar) h1 b h L1 f(2) W h2 L2 Insert Seat Size Master Catalog RIGHT HAND LEFT HAND CTER/L10-2T TO TO $ Clamping Screw CTER/L12-2T TO TO $ CM5x0.8x20-A CTER/L16-2T TO TO $ CM5x0.8x25-A CTER/L10-2T TO TO $ CM5x0.8x16-A CTER/L12-2T TO TO $ CM5x0.8x20-A CTER/L16-2T TO TO $ CM5x0.8x25-A CTER/L10-2T TO TO $ CM5x0.8x16-A CTER/L12-2T TO TO $ CM5x0.8x20-A CTER/L16-2T TO TO $ CM5x0.8x25-A CTER/L10-3T TO TO $ CM5x0.8x16-A CTER/L12-3T TO TO $ CM5x0.8x20-A CTER/L16-3T TO TO $ CM5x0.8x25-A CTER/L10-3T TO TO $ CM5x0.8x16-A CTER/L12-3T TO TO $ CM5x0.8x20-A CTER/L16-3T TO TO $ CM5x0.8x25-A CTER/L16-3T TO TO $ CM5x0.8x25-A CTER/L10-4T TO TO $ CM6x1x16-A CTER/L12-4T TO TO $ CM6x1x20-A CTER/L16-4T TO TO $ CM6x1x25-A CTER/L10-4T TO TO $ CM6x1x16-A CTER/L12-4T TO TO $ CM6x1x20-A CTER/L16-4T TO TO $ CM6x1x25-A CTER/L20-4T TO TO $ CM6x1x25-A EXTERNAL GROOVING & PART-OFF INSERTS NEW ITEM! DGM Type SGM Type Insert Seat Size W re L h k RIGHT HAND NEW ITEM! DGM Type: External grooving & parting off, 2 corner SGM Type: External deep grooving and parting off, 1 corner Please match Insert Seat Size from the table above to select the proper insert Grade AH725 is ideal for steels, stainless steels and titanium alloys. An all-around grade for most materials. Grade GH130 is suited for steels, stainless, cast irons and titanium alloys. est used for interrupted or tough cutting. Grade AH725 LEFT HAND RIGHT HAND Grade GH130 LEFT HAND Tungaloy Ref # TO TO TO TO $19.00 DGM TO TO TO TO $19.00 DGM R/L TO TO TO TO $19.00 DGM R/L TO TO TO TO $19.00 DGM R/L TO TO TO TO $20.00 DGM R/L TO TO TO TO $19.00 DGM TO TO TO TO $19.00 DGM R/L TO TO TO TO $20.00 DGM R/L TO TO TO TO $19.00 DGM R/L TO TO TO TO $20.00 DGM TO TO TO TO $20.00 DGM R/L TO TO TO TO $20.00 DGM R/L TO TO TO TO $11.00 SGM TO TO TO TO $11.00 SGM R/L TO TO TO TO $11.00 SGM TO TO TO TO $11.00 SGM R/L TO TO TO TO $11.00 SGM R/L TO TO TO TO $12.00 SGM TO TO TO TO $12.00 SGM R/L

75 MILLING CUTTERS & INSERTS MULTI-MATERIAL GRADE CARIDE MILLING INSERTS One Grade Offers Outstanding Performance On All Materials Lamina s Multi-MAT technology works on any material-always have the correct grade available and reduce machine idle time! Only one grade is needed for all materials, reducing inventory and costs Swiss made inserts offer unparalled quality that can perform as good as, if not better, than dedicated insert grades of competitors Easier to use! Less grades means less confusion for machinists. Exact cutting data is printed on each box! CALL FOR OUR HOT MILLING SPECIALS! One Grade Does It All! Steel Stainless Steel Cast Iron Super Alloys Grade LT30: Lamina s top quality milling insert grade excels in Super Alloys MADE IN SWITZERLAND ADKT Insert Designation Grade 90 SQUARE SHOULDER MILLING CUTTERS For Use With APLX/APGT1003 Series Inserts APLX APKT APGT SDKT SEKN Insert Shape Clearance Angle Cutting Edge Length L Thick. S Radius CALL FOR OUR HOT MILLING SPECIALS! Lead Angle P Relief Angle D ADKT Inserts-Right Hand Direction- Chamfered (CH) or Honed (H) ADKT1505 PDTR LT POS. 0.6 (15mm) º 15º ADKT1505PDTR-LA $10.70 APLX 1003 PDTR LT 30 1/8-90º 15º APLX1003PDTR-LA $10.70 APLX TR LT POS (10mm) 1/ APLX100308TR-LA $10.70 APLX TR LT 30 Paralellogram 1/ APLX100340TR-LA $10.70 APKT 1604 PDTR LT 30 3/16-90º 15º APKT1604PDTR-LA $10.70 APKT ER LT POS (16mm) 3/ APKT160424ER-LA $10.70 APGT 1604 PDER - Alu LT10 3/16-90º 15º APGT1604ALU-LA $10.70 SDKT Inserts-Neutral-Chamfered (0.031 Corner Edge) SDKT1204 AETN LT 30 Square 15 POS (12mm) 3/ SDKT1204AETN-LA $10.70 SEKN Inserts-Neutral-Chamfered (0.031 Corner Edge) SEKN 42 AFTN / SEKN1203AFTN-LA $10.70 LT 30 Square 20 POS. SEKN 43 AFTN (12mm) 3/ SEKN1204AFTN-LA $10.70 NEW ITEM! G CARIDE INSERTS END MILLS D d L Flute Length H No. of Flutes AP Insert Screws $2.50 each M-EAP10N-5062S1 $93.00 M-SC-AP M-EAP10N-6262S2 $93.00 M-SC-AP M-EAP10N-6262L2 $ M-SC-AP M-EAP10N-7575S3 $ M-SC-AP M-EAP10N-7575L3 $ M-SC-AP M-EAP10N-1010S4 $ M-SC-AP M-EAP10N-1010L4 $ M-SC-AP M-EAP10N-1210S5 $ M-SC-AP M-EAP10N-1210L5 $ M-SC-AP M-EAP10N-1512S6 $ M-SC-AP M-EAP10N-1512L6 $ M-SC-AP10-2 SHELL MILLS. D Arbor Hole d Key Width a Flute Length H No. of flutes AP Insert Screws $2.50 each Torx Wrench [C] TX-208 $6.50 Torx Wrench M-SAP10N $ M-SC-AP10-2 TX Master Catalog 343 DEURRING

76 CHUCK JAWS LATHE WORKHOLDING MILLING CUTTERS 90 SQUARE SHOULDER MILLING CUTTERS For Use With APKT/APGT1604 Series Inserts NEW ITEM! CALL FOR OUR HOT MILLING SPECIALS! G MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS END MILLS D d L Flute Length H No. of Flutes AP M-EAP16N-1010S2 $ M-EAP16N-1010L2 $ M-EAP16N-1210S3 $ M-EAP16N-1210L3 $ M-EAP16N-1512S4 $ M-EAP16N-1512L4 $ SHELL MILLS. D Arbor Hole d Key Width a Flute Length H No. of Flutes AP M-SAP16N $ M-SAP16N $ M-SAP16N $ M-SAP16N $ M-SAP16N $ M-SAP16N $ M-SAP16N $ Insert Screws $2.50 each M-SC-AP16 Insert Screws $2.50 each M-SC-AP16 Torx Wrench [C] TX-208 $6.50 Torx Wrench [C] TX-208 $6.50 INDEXALE DRILLS TURNING & ORING 45 LEAD HIGH POSITIVE SHELL MILLS For Use With SDKT1204 Series Inserts NEW ITEM! CALL FOR OUR HOT MILLING SPECIALS! ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS D Arbor Hole d UTTON INSERT SHELL MILLS For Use With RDMT1204 Series Inserts Key Width a Flute Length H No. of Flutes AP M-SSD12F $ M-SSD12F $ M-SSD12F $ M-SSD12F $ M-SSD12F $ CALL FOR OUR HOT MILLING SPECIALS! NEW ITEM! Insert Screw M-SC-AP16 $2.50 Torx Wrench [C] TX-208 $6.50 MRO & SAFETY FLAT STOCK/DRILL ROD D Arbor Hole d Key Width a Flute Length H No. of Flutes Master Catalog AP M-SRD $ M-SRD $ M-SRD $ Insert Screw M-SC-AP16 $2.50 Torx Wrench [C] TX-208 $6.50

77 MILLING CUTTERS SUPER HIGH FEED SHELL MILLS & ENDMILLS Newly designed cutting edge geometry allows 3-5 times higher feed than conventional tools Utilizes thicker inserts and higher clamping stability Coolant holes minimize edge damage resulting from chip build up Machining Capability: shouldering, grooving, ramping, plunging, traversing, englarging hole diameter TXP High Feed Milling Cutter Cutting No. of d E F a b D Inserts TO-TXP05250RU $ TO-TXP05300RU $ TO-TXP06250RU $ TO-TXP06300RU $ TO-TXP08050RU $ TO-TXP08300RU $ TO-TXP08400RU $ TO-TXP09250RU $ TO-TXP09300RU $ TO-TXP09400RU $ TO-TXP09500RU $ TO-TXP09600RU $ Applicable Insert WPMT05... WPMT06... WPMT08... WPMT09... EXP High Feed Endmill Cutting D SUPER HIGH FEED INSERTS Newly designed cutting edge geometry allows 3-5 times higher feed than conventional tools Utilizes thicker inserts and higher clamping stability Machining Capability: shouldering, grooving, ramping, plunging, traversing, englarging hole diameter d L L1 L2 Type No. of Inserts Weldon 2 TO-EXP05075RSU $ Straight 2 TO-EXP05075RLU $ Straight 2 TO-EXP05075RLLU $ Weldon 2 TO-EXP06100RSU $ Straight 2 TO-EXP06100RLU $ Straight 2 TO-EXP06100RLLU $ Weldon 3 TO-EXP06125RSU $ Straight 3 TO-EXP06125RLU $ Weldon 3 TO-EXP06150RSU $ Straight 3 TO-EXP06150RLU $ Straight 3 TO-EXP06150RLLU $ Weldon 2 TO-EXP09200RU $ Weldon 2 TO-EXP09200RLU $ Applicable Insert WPM*05H315ZPR WPM*06X415ZPR WPMT090425Z*R CARIDE INSERTS Grade Industry Reference Class AH120 AH140 T3030 WPMT05H315ZPR-ML M TO-8575 $9.10 TO-8576 $9.10 TO-8577 $9.10 WPMT05H315ZPRMH M TO-8573 $9.10 TO-8574 $ WPMT060415ZPR-ML M TO-8781 $9.10 TO-8782 $9.10 TO-8780 $9.10 WPMT060415ZPR-MH M TO-8783 $9.10 TO-8784 $ WPMT080615ZSR M TO-8578 $10.22 TO-8579 $10.22 TO-8580 $10.22 WPMT080615ZPR-ML M TO-8734 $10.22 TO-8735 $10.22 TO-8736 $10.22 WPMT080615ZSR-MH M TO-8742 $10.22 TO-8743 $ WPMT090725ZSR M TO-8729 $11.84 TO-8730 $ WPMT090725ZPR-ML M TO-8731 $11.84 TO-8740 $11.84 TO-8741 $11.84 WPMT090725ZSR-MH M TO-8732 $11.84 TO-8733 $ REPLACEMENT PARTS Cutter Model Clamping Screw Clamp Set Wrench EXP05 TO-CSP-3.5S - TO-IP-15D EXP06 TO-CSP-4S TO-CSY-15 EXP09 TO-CSP-5 TO-CSY-20 TO-IP-20T TXP05 TO-CSP-3.5S - TO-IP15D TXP06 TO-CSP-4S TO-CSY15 TO-IP15D TXP08 TO-CST5 TO-CSX20 TO-T20T TXP09 TO-CSTP5 TO-CSY20 TO-IP20T Master Catalog 345 DEURRING

78 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS 45 & 90 MILLING CUTTERS TAW 45 LEAD FACE MILLS 45 lead high positive high feed face mill Highly rigid cutter, 20-30% lighter than competition Features coolant holes and highly accurate pocket design Nickel plating for corrosion and wear resistance Change from 45 lead to 30 lead using HJ chipbreaker Unique double relief angle for increased cutting edge strength and increased accuracy Cutting D No. of Teeth D1 d E F a b Coolant Hole TO-TAW13R2U7503 $ YES TO-TAW13R2U7504 $ YES TO-TAW13R2U7505 $ YES TO-TAW13R3U1004 $ YES TO-TAW13R3U1006 $ YES TO-TAW13R3U1008 $ YES TO-TAW13R4U1505 $ YES TO-TAW13R4U1507 $ YES TO-TAW13R4U1510 $ YES TO-TAW13R5U1506 $ YES TO-TAW13R5U1508 $ YES TO-TAW13R5U1512 $ YES TO-TAW13R6U2007 $ NO TO-TAW13R6U2010 $ NO TO-TAW13R6U2016 $1, NO TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD TPW 90 LEAD FACE MILLS 90 lead high positive high feed face mill Highly rigid cutter, 20-30% lighter than competition Features coolant holes and highly accurate pocket design Nickel plating for corrosion and wear resistance Unique double relief angle for increased cutting edge strength and increased accuracy INSERTS Master Catalog GRADES Industry Reference Class Honing AH120 AH140 T3030 SWMT13T3AFPR-MJ M With TO $10.06 TO $10.06 TO $10.06 SWMT13T3AFER-ML M With TO $ SWMW13T3AFTR M With TO $ TO $10.06 SWMT13T3AFPR-HJ M With TO $10.06 TO $10.06 TO $10.06 SWMT13T3AFPR-MS M With - - TO $ SWGT13T3AFPR-MJ G Without TO $ Shim TO-FSSA1102 Cutting D No. of Teeth Insert Screw TO-CSP-3.5 Shim Screw TO-DTS5-3.5SS Shim Wrench TO-P-3.5 d E F a b Insert Wrench TO-IP-15D TO-TPW13R2U75A3 $ TO-TPW13R2U7504 $ TO-TPW13R2U7505 $ TO-TPW13R3U1004 $ TO-TPW13R3U1006 $ TO-TPW13R3U1008 $ TO-TPW13R4U1505 $ TO-TPW13R4U1507 $ TO-TPW13R4U1510 $ TO-TPW13R5U1506 $ TO-TPW13R5U1508 $ TO-TPW13R5U1512 $ TO-TPW13R6U2008* $ TO-TPW13R6U2012* $1, TO-TPW13R6U0215* $1, *Does Not Have Coolant Hole INSERTS GRADES Max. Industry Reference Class Honing AH120 AH140 T3030 KS05F DOC (in) SWMT1304PDPR-MJ M With TO $10.06 TO $10.06 TO $ SWMT1304PDER-ML M With TO $ SWMT1304PDPR-MS M With - - TO $ SWGT1304PDFR-AJ G Without TO $ SWGT1304PDPR-MJ G With TO $ Shim TO-FSSP1102 Insert Screw TO-CSP-3.5 Shim Screw TO-DTS5-3.5SS Shim Wrench TO-P-3.5 Insert Wrench TO-IP-15D

79 MILLING CUTTERS TRD SERIES JETMILL ROUND INSERT FACE MILL High Positive Multi-Finctional Design Capable of Plunging, Ramping and Circle Interpolation High Strength Round Insert High Feed Capabilities Superior Surface Finishes Reference No. Of Teeth Cutting Dimensions (Inch) D (in) d (in) R F a b Corner Angle - Rake Angle Wt. Lbs. Axial +10 Radial -6 ~ 0 TRD12050RU TO-TRD12050RU $ RDMT 12 TRD16080RU TO-TRD16080RU $ RDMT 16 TRD16100RU TO-TRD16100RU $ RDMT 16 TRD16125RU TO-TRD16125RU $ RDMT 16 INSERTS Work Materials Recommended Grade RECOMMENDED CUTTING CONDITIONS Chip reaker REPLACEMENT PARTS TO-TRD12050 TO-TRD12080/ 100/125 INSERTS FOR TRD SERIES JETMILL Reference Class Grade Screw TO-CST3.5 TO-CST5 $1.79 Wrench TO-T-15D TO-T-20D $12.56 Insert RDMT1204ZDPN-MJ M AH120 TO-2051 $11.61 RDMT1606ZDPN-MJ M AH120 TO-2053 $14.19 Roughing Finishing sfm ipt sfm ipt Mild Steels AH120 MJ 400~ ~ ~ ~0.024 Alloy Steels /300H AH120 MJ 350~ ~ ~ ~0.020 Medium Carbon Steels 250H AH120 MJ 400~ ~ ~ ~0.024 Stainless Steels AH120 MJ 300~ ~ ~ ~0.020 Die Steels AH120 MJ 250~ ~ ~ ~0.018 Cast Irons AH120 MJ 400~ ~ ~ ~0.024 Super Alloys AH120 MJ 125~ ~ ~ ~0.012 DIAMOND PLATE SPONGECOTE Anti-Fatigue Mats-No. 415 mond-plate SpongeCote is the most popular anti-fatigue mat in the industry because no other offers such a complete package of exceptional comfort, long life, and a high-tech, industrial image. Its exceptionally resilient Nitricell sponge base defines the mat by providing true comfort, enhancing productivity, and reviving morale, all while relieving fatigue throughout the day. The safety-engineered surface adds traction and durability, and is ideal for heavily trafficked areas. EST SELLER! Ideal For Heavily Trafficked Areas! Please See Our Large Variety Of Safety And Anti-Fatigue Mats On Pages ! For use in dry work areas Anti-fatigue Nitricell sponge base for unparalleled comfort Safety beveled edges Slip and wear resistant 3 Year Warranty Size Thickness Color 2' x 3 9/16 lack WW K $47.27 lk/yellow WW Y $ ' x 5 9/16 lack WW K $ lk/yellow WW Y $ Master Catalog 347 D CARIDE INSERTS DEURRING

80 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES MILLING CUTTERS TUNGALOY STYLE 90 MILLING CUTTERS High Positive Design Free Cutting Excellent Chip Control SHELL MILL E COOLANT FED END MILL RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS Description ENDMILLS SHELL MILLS.. No. Of Teeth T $ T $ T $ T $ T $ T $ T-2000 $ T-2005 $ T-3000 $ T-4000 $ Milling Cutter Quantity Discounts 1 pc. LIST 2 pcs. 10% OFF 5 pcs. 15% OFF Extra Screw $ 1.00 SC-01 SC-01 SC-02 Extra Screws Quantity Discounts 1-9 LIST % OFF % OFF % OFF % OFF Wrench [C] TX-20F Flag Style $2.00 TX-20S Screwdriver Style $5.00 INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD INSERTS INSERTS FOR T MILLING CUTTERS MATERIAL Reference Polished Coated For Aluminum, Copper, rass For Mild Steel, Stainless Steel, Super Alloys For Alloy Steels, Die Steels, Cast Iron Work Materials SDGT1204PDFR-AJ-TH10 RECOMMENDED CUTTING CONDITIONS Recommended Grade.187 Roughing US-820 $10.90 SDMT1204PDPR-ML-AH120 - SDMT1204PDSR-MJ-AH Master Catalog Finishing sfm ipt sfm ipt Quantity Discounts LIST % OFF % OFF % OFF % OFF % OFF US-821 $9.40 US-822 $9.40 Mild Steels US ~ ~ ~ ~0.008 Alloy Steels US ~ ~ ~ ~0.010 Stainless Steels US ~ ~ ~ ~0.008 Die Steels US ~ ~ ~ ~0.008 Cast Irons US ~ ~ ~ ~0.008 Super Alloys US ~ ~ ~ ~0.006 Aluminum Alloys US ~ ~ ~ ~0.008

81 MILLING CUTTERS CAROLOY STYLE INDEXALE MILLING CUTTERS Cutting diameters from 5/8 to 2 End mills and shell mills available Made in D End Mills Cutting No. Of Teeth 5/ EM-APFT-625 $ / EM-APFT-750 $ EM-APFT-1075 $ EM-APFT-1000 $ / EM-APFT-1250 $ / EM-APFT-1510 $ / EM-APFT-1512 $ Shell Mills Cutting No. Of Teeth SM-APFT-2000 $ INDEXALE MILLING CUTTERS ENDMILLS & SHELL MILLS Using AP Inserts Grade PV 311 US-811 $8.60 Inserts- APKT 1604 PDER Grade Grade NN 52 DHCP35M US-812 $7.85 DN94884 Grade DASK25M $7.25 DN94893 $8.95 Inserts- APKT 1604 PDER Grade Grade Grade NN 52 DHCP35M DASK25M US-811 US-812 DN94884 DN94893 $8.60 $7.85 $7.25 $8.95 Endmills Using AP 10 an AP 16 Inserts Uses Insert Cutting Shell Mills Using AP 16 Inserts Cutting Height Key Width Flute Length No of Flutes D D2 L L2 z No of Flutes D H K z Accessories Description Screws - C04011 SC-51 $1.00 Torx wrench TX-215 $5.00 Industry Reference Industry Reference AP EM-AP C $91.62 AP EM-AP C $91.62 AP EM-AP C $91.62 AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ Long Reach Endmills Using AP 10 an AP 16 Inserts Uses Insert Cutting Flute Length No of Flutes D D2 L L2 z / Grade US-811 PV 311 US-812 NN52 DN94884 DHCP35M DN94893 DASK25M Industry Reference Grade Information recommended for milling of stainless steels and other high temperature materials The ideal choice for machining steels and stainless steels for machining carbon steel, alloy steel, and stainless steel For medium to difficult milling operations in dry or wet conditions AP EM-AP C $91.62 AP EM-AP C $91.62 AP EM-AP C $91.62 AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ AP EM-AP C $ SM-AP16-15-C $ SM-AP16-20-C $ SM-AP16-25-C $ SM-AP16-30-C $ SM-AP16-40-C $ SM-AP16-50-C $ SM-AP16-60-C $ SM-AP16-80-C $ Master Catalog 349 CARIDE INSERTS DEURRING

82 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES MILLING INSERTS MULTI-MATERIAL GRADE CARIDE MILLING INSERTS One Grade Offers Outstanding Performance On All Materials Lamina s Multi-MAT technology works on any material-always have the correct grade available and reduce machine idle time! Only one grade is needed for all materials, reducing inventory and costs Swiss made inserts offer unparalled quality that can perform as good as, if not better, than dedicated insert grades of competitors Easier to use! Less grades means less confusion for machinists. Exact cutting data is printed on each box! CALL FOR OUR HOT MILLING SPECIALS! One Grade Does It All! Steel Stainless Steel Cast Iron Super Alloys Grade LT30: Lamina s top quality milling insert grade excels in Super Alloys MADE IN SWITZERLAND RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ADKT Insert Designation Grade SEKN SHELL MILL CUTTERS Using SE 42 Inserts APLX APKT APGT SDKT SEKN Insert Shape Clearance Angle Cutting Edge Length L Thick. S Radius Lead Angle P Relief Angle D ADKT Inserts-Right Hand Direction- Chamfered (CH) or Honed (H) ADKT1505 PDTR LT POS. 0.6 (15mm) º 15º ADKT1505PDTR-LA $10.70 APLX 1003 PDTR LT 30 1/8-90º 15º APLX1003PDTR-LA $10.70 APLX TR LT POS (10mm) 1/ APLX100308TR-LA $10.70 APLX TR LT 30 Paralellogram 1/ APLX100340TR-LA $10.70 APKT 1604 PDTR LT 30 3/16-90º 15º APKT1604PDTR-LA $10.70 APKT ER LT POS (16mm) 3/ APKT160424ER-LA $10.70 APGT 1604 PDER - Alu LT10 3/16-90º 15º APGT1604ALU-LA $10.70 SDKT Inserts-Neutral-Chamfered (0.031 Corner Edge) SDKT1204 AETN LT 30 Square 15 POS (12mm) 3/ SDKT1204AETN-LA $10.70 SEKN Inserts-Neutral-Chamfered (0.031 Corner Edge) SEKN 42 AFTN / SEKN1203AFTN-LA $10.70 LT 30 Square 20 POS. SEKN 43 AFTN (12mm) 3/ SEKN1204AFTN-LA $10.70 ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD D H K z Cutting Height Key Width No Of Flutes Reference SM-SEKN4-20-C $ SM-SEKN4-25-C $ SM-SEKN4-30-C $ SM-SEKN4-40-C $ SM-SEKN4-50-C $ SM-SEKN4-60-C $ SM-SEKN4-80-C $ SM-SEKN4-100-C $1, SM-SEKN4-120-C $1, SEKN INSERTS Master Catalog Clamp Screw Clamp Seat Seat Screw Wrench CA-1006L CA-2063 CA-3010 CA-4012 CA-5004 CA-1077 CA-5620 CA-6488 CA-6489 CA-6918 TUNGALOY GRADE LAMINA GRADE Inch No Metric No AH330 AH120 TH10 UX30 LT30 SEKN42AFTN SEKN1203AFTN TO-2142 $9.63 TO-2141 $9.63 SEKN42AFFN SEKN1203AFFN TO-2140 $7.74 TO-2145 $ SEKN1203AFTN-LA $9.63 SEKN1204AFTN-LA $9.63

83 INDEXALE MILLING CUTTERS MILLING CUTTERS Using TP 22/32 Inserts INSERTS SHELL MILLS Uses Insert D H K z Cutting Height Key Width No Of Flutes Reference TP SM-TP32-15-C $ TP SM-TP32-40-C $ TP SM-TP32-25-C $ TP SM-TP32-30-C $ TP SM-TP32-40-C $ END MILLS Uses Insert D D2 L L2 z Cutting Height Key Width No Of Flutes Reference TP EM-TP C $ TP EM-TP C $ TP EM-TP C $ TP EM-TP C $ TP EM-TP C $ GRADE Clamp Screw Inch No Metric No AH120 T3030 T325 NS540 TH10 UX30 TPU221 TPMN TO-3076 $3.09 TO-3078 $3.09 TO-3079 $3.09 TPU222 TPMN TO-3081 $ TO-3083 $3.09 TO-3084 $3.09 TPU321 TPMN TO-3085 $7.35 TO-8023 $7.35 TO-3087 $ TO-3089 $5.63 TO-3090 $5.63 TPU322 TPMN TO-3091 $ TO-3093 $7.35 TO-3097 $5.63 TO-3095 $5.63 TO-3096 $5.63 Wrench Clamp CA-1006 CA-5004 CA-2064 Screw Wrench Clamp CA-1005 CA-5025 CA-2010 CA-1016 CA-5004 CA-2064 INDEXALE MILLING CUTTERS FEATURES: Uses APKT 1003 PDR Inserts (not included) Durable and unique chrome nickel coated holder Positive chip control INDEXALE MILLING CUTTERS Nomenclature Cutter Master Catalog 351 DOC No. Of Flutes AAP /8 1/ /2 1 MI $99.15 AAP /2 1/ /2 1 MI $ AAP /8 1/ /2 2 MI $ AAP /4 3/4 4 3/8 2 3 MI $ AAP /4 4 3/8 2 4 MI $ AAP /4 3/4 4 3/8 2 5 MI $ Uses APKT 1003 PDR Inserts INDEXALE COOLANT-THRU MILLING CUTTERS Nomenclature Cutter DOC No. Of Flutes AAAP /8 1/ /2 1 MI $ AAAP /2 1/ /2 1 MI $ AAAP /8 1/ /2 2 MI $ AAAP /4 3/4 4 3/8 2 3 MI $ AAAP /4 4 3/8 2 4 MI $ AAAP /4 3/4 4 3/8 2 5 MI $ Uses APKT 1003 PDR Inserts 3 PIECE COOLANT-THRU MILLING SET 1/2 Cutter 3/8 1/2 5/8 No. Of Flutes Description Set of 3 pcs. AAAP with APKT 1003 PDR Insert, Torx Screw & Torx Key Set MI $ CARIDE INSERTS DEURRING

84 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ISCAR MILLING INSERTS ADKT R-HM ADKT 1505 PDR-HM ADKT 1505 PDTR-76 ADKT 1505 PDTR-RM ADMT 1505 PDR-HS APKT 1003 PDR-HM APKT 1003 PDTR-76 APKT 1003 PDTR-RM OEMT AER-76 REMT 1505 LM-76 Iscar Reference ADKR 1505 PDR-HM ADKT R-HM ADKT R-HM ADKT R-HM Master Catalog GRADE IC-250 IC-328 IC-635 IC-928 IC-950 CAR-2101 $16.40 CAR-2121 $16.40 CAR-2141 $16.40 CAR-2161 $16.40 ADKT R-HM -- ADKT R-HM ADKT 1505 ADR-HM ADKT 1505 PDR-HM ADKT 1505 PDTR-76 ADKT 1505 PDTR-RM ADMT 1503 PDR-HM ADMT 1505 PDR-HS APKT PDTR-RM CAR-2201 $17.95 CAR-2221 $16.40 CAR-2241 $16.40 CAR-2261 $14.04 CAR-2281 $14.04 CAR-2301 $14.04 CAR-2321 $16.40 CAR-2341 $12.36 APKT TR-RM -- APKT PDTR-RM APKT PDTR-RM APKT TR-RM APKT 1003 PDR-HM APKT 1003 PDTR-76 APKT 1003 PDTR-RM CAR-2381 $12.36 CAR-2401 $12.36 CAR-2421 $12.36 CAR-2441 $12.36 CAR-2461 $12.36 CAR-2481 $12.36 O45MT RM -- OEMT AER-76 OFMT 07T3-AER-76 CAR-2521 $14.14 CAR-2541 $14.14 R90MT 43-RM -- R9OMT 1205-RM -- REMT 1505 LM RFMT 1905 LM CAR-2102 $16.40 CAR-2122 $16.40 CAR-2142 $16.40 CAR-2162 $16.40 CAR-2182 $16.40 CAR-2202 $17.95 CAR-2222 $16.40 CAR-2242 $16.40 CAR-2262 $14.04 CAR-2282 $14.04 CAR-2302 $14.04 CAR-2322 $16.40 CAR-2342 $12.36 CAR-2362 $12.36 CAR-2382 $12.36 CAR-2402 $12.36 CAR-2422 $12.36 CAR-2442 $12.36 CAR-2462 $12.36 CAR-2482 $12.36 CAR-2502 $14.14 CAR-2522 $14.14 CAR-2542 $14.14 CAR-2562 $13.24 CAR-2582 $13.24 CAR-2602 $13.24 CAR-2622 $ CAR-2123 $16.40 CAR-2143 $16.40 CAR-2163 $16.40 CAR-2183 $16.40 CAR-2203 $17.95 CAR-2223 $16.40 CAR-2243 $16.40 CAR-2263 $14.04 CAR-2283 $14.04 CAR-2303 $14.04 CAR-2323 $16.40 CAR-2343 $12.36 CAR-2363 $12.36 CAR-2104 $16.40 CAR-2124 $16.40 CAR-2144 $16.40 CAR-2164 $16.40 CAR-2184 $16.40 CAR-2204 $17.95 CAR-2105 $16.40 CAR-2125 $ CAR-2185 $ CAR-2244 $16.40 CAR-2264 $16.40 CAR-2284 $ CAR-2265 $16.40 CAR-2285 $ CAR-2443 $11.77 CAR-2463 $11.77 CAR-2483 $ CAR-2524 $14.14 CAR-2544 $ CAR-2604 $13.24 CAR-2505 $14.14 CAR-2525 $14.14 CAR-2545 $14.14 CAR-2565 $13.24 CAR-2585 $13.24 CAR-2605 $ Grade Chart Ansi Workpiece Material Recommended Applications IC250 PVD COATING C6-C7 Steel and cast steel. Stainless steel. Roughing. Medium speed. High feed. Interrupted cut. IC328 PVD COATING C3-C2 Alloy steel.aluminum alloys. Austenitic stainless steel. Carbon steel. Cast steel. Copper alloys. Exotic alloys. Roughing. Low speed. High speed. High feed. Interrupted cut. High resistance to mechanical & thermal shock. IC635 CVD COATED C6-C5 Carbon steel. Allot steel. Stainless steel. Low speed,high feed and unfavorable conditions. IC928 PVD COATING C6-C5 Alloy steel.aluminum alloys. Austenitic stainless steel. Carbon steel. Cast steel. Copper alloys. Exotic alloys. Roughing. Low speed. High speed. High feed. Interrupted cut. High resistance to mechanical & thermal shock. IC950 PVD COATING C7-C5 For carbon and alloy steels. Also for gray cast irons. High speed milling at medium feed, no coolant needed Iscar

85 GROOVING & THREADING TOOLS THREADING & GROOVING TOOLS Call us for the most complete line of threading and grooving tools from Toolflo, Carmex & Micro 100. We will be glad to assist you with all your threading and grooving needs. We Proudly Offer Threading & Grooving Products From: TOOLFLO GROOVING & THREADING INSERT GRADES Grade Class Application GP4 C1/C5 TiN Coated Sub Micron - For Aluminum, Cast Iron, 300/400 Stainless Steel, Non Metals, Carbon/Alloy Steel, Ductile Iron GP22 C1 Tin Coated - For Aluminum, Cast Iron, 300 Series Stainless Steel, Non Metals C3 C2-C3 Uncoated, Aluminum, Non Ferrous metals, Plastics GP3 C2-C3 TiN Coated Sub Micron - High Temp Alloys, 300 Series Stainless AT3 C3 TiAlN Coated Sub Micron - est grade for High Temp Alloys and 300 Series stainless GP50 C5 TiN Coated Sub Micron - For Carbon/Alloy Steels, 400 Series Stainless steels, Ductile Cast Iron AT50 C5 TiAlN Coated - For Carbon/Alloy Steels, 400 Series Stainless steels, Ductile Cast Iron TOOLFLO GROOVING & THREADING INSERT CHIPREAKERS Chipbreaker Operation HC General Purpose breaker C Fine finish breaker FC Ultra fine finish breaker CARIDE INSERTS DEURRING Call Us For All Of Your Threading & Grooving Needs! Master Catalog 353

86 CHUCK JAWS LATHE WORKHOLDING SMALL HOLE GROOVING & THREADING SMALL HOLE 60 V THREADING INSERTS MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING Min ore oring ar Type Left or Right TPI A Angle M F E H T Grade GP22 Grade GP4 FR3 RIGHT T-FR360VGP22 $ HR3 RIGHT T-HV002GP22 $14.49 T-HV002GP4 $14.49 RIGHT T-NVR60GP22 $14.49 T-NVR60GP4 $14.49 LEFT T-NVL60GP22 $14.49 T-NVL60GP4 $ FR3 RIGHT T-FR460VGP22 $16.42 T-FR460VGP4 $ TR RIGHT T-TVR60GP4 $19.22 SMALL HOLE- FULL NOSE RADIUS GROOVING INSERTS Full Line Available! Please call for more information. Min ore oring ar Type Left or Right RIGHT TR RIGHT W D T SMALL HOLE- STANDARD GROOVING INSERTS Grade GP22 Grade GP T-NRR031WGP22 $14.49 T-NRR031WGP4 $ T-NRR047WGP22 $14.49 T-NRR047WGP4 $ T-NRR062WGP22 $14.49 T-NRR062WGP4 $ T-NRR094WGP22 $14.49 T-NRR094WGP4 $ T-NRR125WGP22 $14.49 T-NRR125WGP4 $ T-TRR062WGP22 $18.04 T-TRR062WGP4 $ T-TRR094WGP4 $ T-TRR125WGP4 $18.04 ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Min ore oring ar Type Left or Right W D T Grade GP Master Catalog Grade GP4 FR3 RIGHT T-FR3031WGP22 $ RIGHT T-NGR031WGP22 $14.49 T-NGR031WGP4 $14.49 LEFT RIGHT T-NGR047WGP22 $14.49 T-NGR047WGP4 $ LEFT RIGHT T-NGR062WGP22 $14.49 T-NGR062WGP4 $14.49 LEFT RIGHT T-NGR094WGP22 $14.49 T-NGR094WGP4 $14.49 RIGHT T-NGR125WGP22 $14.49 T-NGR125WGP4 $ FR3 RIGHT T-FR4031WGP22 $ T-TGR062WGP4 $ TR RIGHT T-TGR094WGP4 $ T-TGR125WGP4 $18.04

87 TOP NOTCH COMPATILE GROOVING INSERTS SMALL HOLE THREADING & GROOVING ARS Full Line Available! Please call for more information. DEEP GROOVING-SINGLE ENDED INSERTS Gage meter W Inch W mm W Inch W mm E T A Toolholder/ oring ar GT GT GT GT GT GT-4 DEEP GROOVING-SINGLE ENDED INSERTS Full Nose Radius-Gage meter Full Line Available! Please call for more information. E T A oring ar Type FR3 HR3 Toolholder/ oring ar GT GT GT GT-4 FR4 TR Material Steel Heavy Metal Left or Right Coolant Port Grade AT3 Left or Right Hand Grade GP3 Min ore L D C F H Grade GP50 RIGHT T-FLGD3094RG3 $12.27 T-FLGD3094RG5 $12.27 LEFT T-FLGD3094LG3 $12.27 T-FLGD3094LG5 $12.27 RIGHT T-FLGD3125RG3 $12.27 T-FLGD3125RG5 $12.27 LEFT T-FLGD3125LG3 $12.27 T-FLGD3125LG5 $12.27 RIGHT T-FLGD3189RG3 $12.27 T-FLGD3189RG5 $12.27 LEFT T-FLGD3189LG3 $12.27 T-FLGD3189LG5 $12.27 RIGHT T-FLGD4125RG3 $22.22 T-FLGD4125RG5 $22.22 LEFT T-FLGD4125LG3 $22.22 T-FLGD4125LG5 $22.22 RIGHT T-FLGD4189RG3 $15.46 T-FLGD4189RG5 $15.46 LEFT T-FLGD4189LG3 $15.46 T-FLGD4189LG5 $15.46 RIGHT T-FLGD4250RG3 $15.47 T-FLGD4250RG5 $15.47 LEFT T-FLGD4250LG3 $15.47 T-FLGD4250LG5 $15.47 Grade GP3 Grade GP50 RIGHT T-FLRD3062RA3 $13.47 T-FLRD3062RG3 $12.27 T-FLRD3062RG5 $12.27 LEFT T-FLRD3062LA3 $13.47 T-FLRD3062LG3 $12.27 T-FLRD3062LG5 $12.27 RIGHT T-FLRD3094RA3 $13.47 T-FLRD3094RG3 $12.27 T-FLRD3094RG5 $12.27 LEFT T-FLRD3094LA3 $13.47 T-FLRD3094LG3 $12.27 T-FLRD3094LG5 $12.27 RIGHT - - T-FLRD4094RG3 $15.46 T-FLRD4094RG5 $15.46 LEFT T-FLRD4094LA3 $16.54 T-FLRD4094LG3 $15.46 T-FLRD4094LG5 $15.46 RIGHT T-FLRD4125RA3 $16.54 T-FLRD4125RG3 $15.46 T-FLRD4125RG5 $15.46 LEFT T-FLRD4125LA3 $16.54 T-FLRD4125LG3 $15.46 T-FLRD4125LG5 $15.46 N T-FR-312S $ Y T-FR-312SC $ N T-FR-312HM $ Y T-FR-312HMC $ Steel N T-HR-312S $ Heavy Metal N T-HR-312HM $ Steel Heavy Metal Carbide N T--312S $ N T--344S $ N T--375S $ N T--440S $ N T--312HM $ N T--344HM $ N T--375HM $ N T--440HM $ N T--312C $ N T--440C $ Steel N T-FR-400S $ Heavy Metal N T-FR-400HM $ Steel N T-TR-500S $ Heavy Metal N T-TR-500HM $ Master Catalog 355 CARIDE INSERTS DEURRING

88 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING TOP NOTCH COMPATILE GROOVING INSERTS DEEP GROOVING-DOULE ENDED INSERTS Gage meter DEEP GROOVING-DOULE ENDED INSERTS Full Nose Radius-Gage meter W Inch W Inch W mm W mm FACE GROOVING-DOULE ENDED INSERTS Gage meter E T A External Grooving Only W Inch W mm E T A E T A Toolholder/ oring ar GT GT GT-3 External Grooving Only Left or Right Left or Right Grade GP3 Grade GP3 Left or Right Hand Grade GP50 RIGHT T-FLRT3062RG5 $20.83 LEFT T-FLRT3062LG5 $20.83 RIGHT T-FLRT3094RG5 $20.83 LEFT T-FLRT3094LG5 $20.83 RIGHT T-FLRT4062RG5 $24.75 LEFT T-FLRT4062LG5 $24.75 RIGHT T-FLRT4094RG5 $24.75 LEFT T-FLRT4094LG5 $24.75 RIGHT T-FLRT4125RG5 $24.75 LEFT T-FLRT4125LG5 $24.75 Grade GP50 Grade GP50 RIGHT T-FLGT3094RG3 $20.83 T-FLGT3094RG5 $20.83 LEFT T-FLGT3094LG3 $20.83 T-FLGT3094LG5 $20.83 RIGHT T-FLGT3125RG3 $20.83 T-FLGT3125RG5 $20.83 LEFT T-FLGT3125LG3 $20.83 T-FLGT3125LG5 $20.83 RIGHT T-FLGT3189RG3 $20.83 T-FLGT3189RG5 $20.83 LEFT T-FLGT3189LG3 $20.83 T-FLGT3189LG5 $20.83 RIGHT T-FLGT4125RG3 $24.75 T-FLGT4125RG5 $24.75 LEFT T-FLGT4125LG3 $24.75 T-FLGT4125LG5 $24.75 RIGHT T-FLGT4189RG3 $24.75 T-FLGT4189RG5 $24.75 LEFT T-FLGT4189LG3 $24.75 T-FLGT4189LG5 $24.75 RIGHT T-FLGT4250RG3 $24.75 T-FLGT4250RG5 $24.75 LEFT T-FLGT4250LG3 $24.75 T-FLGT4250LG5 $24.75 RIGHT T-FLF3125RG3 $15.41 T-FLF3125RG5 $15.41 LEFT T-FLF3125LG3 $15.41 T-FLF3125LG5 $15.41 RIGHT T-FLF3156RG3 $15.41 T-FLF3156RG5 $15.41 LEFT T-FLF3156LG3 $15.41 T-FLF3156LG5 $15.41 RIGHT T-FLF3188RG3 $15.41 T-FLF3188RG5 $15.41 LEFT T-FLF3188LG3 $15.41 T-FLF3188LG5 $15.41 ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS, DRILLS TAPS & REAMERS Full Line Available! Please call for more information Master Catalog

89 TOP NOTCH COMPATILE GROOVING INSERTS STANDARD GROOVING-DOULE ENDED INSERTS Gage meter-series 2 Inserts: All Others: Full Line Available! Please call for more information. W Inch W mm E T A Tooholder/ oring ar Left or Right Hand Grade AT50 Grades AT3 Grade GP50 TiAlN C5 Coated Larger Groove Widths & Series 4 & 6 Top Notch Also Available.Please Call For More Information. TiAlN C2-C3 Coated C5 TiN Coated GT-2 RIGHT T-FLG2031RA5 $16.48 T-FLG2031RA3 $16.48 T-FLG2031RG5 $ GT-2 LEFT T-FLG2031LA5 $16.48 T-FLG2031LA3 $16.48 T-FLG2031LG5 $ GT-2 RIGHT T-FLG2041RA5 $16.48 T-FLG2041RA3 $16.48 T-FLG2041RG5 $ GT-2 LEFT T-FLG2041LA5 $16.48 T-FLG2041LA3 $16.48 T-FLG2041LG5 $ GT-2 RIGHT T-FLG2047RA5 $16.48 T-FLG2047RA3 $16.48 T-FLG2047RG5 $ GT-2 LEFT T-FLG2047LA5 $16.48 T-FLG2047LA3 $16.48 T-FLG2047LG5 $ GT-2 RIGHT T-FLG2058RA5 $16.48 T-FLG2058RA3 $16.48 T-FLG2058RG5 $ GT-2 LEFT T-FLG2058LA5 $16.48 T-FLG2058LA3 $16.48 T-FLG2058LG5 $ GT-2 RIGHT T-FLG2062RA5 $16.48 T-FLG2062RA3 $16.48 T-FLG2062RG5 $ GT-2 LEFT T-FLG2062LA5 $16.48 T-FLG2062LA3 $16.48 T-FLG2062LG5 $ GT-2 RIGHT T-FLG2094RA5 $16.48 T-FLG2094RA3 $16.48 T-FLG2094RG5 $ GT-2 LEFT T-FLG2094LA5 $16.48 T-FLG2094LA3 $16.48 T-FLG2094LG5 $ GT-2 RIGHT T-FLG2125RA5 $16.48 T-FLG2125RA3 $16.48 T-FLG2125RG5 $ GT-2 LEFT T-FLG2125LA5 $16.48 T-FLG2125LA3 $16.48 T-FLG2125LG5 $ GT-3 RIGHT T-FLG3031RA5 $16.48 T-FLG3031RA3 $16.48 T-FLG3031RG5 $ GT-3 LEFT T-FLG3031LA5 $16.48 T-FLG3031LA3 $16.48 T-FLG3031LG5 $ GT-3 RIGHT T-FLG3047RA5 $16.48 T-FLG3047RA3 $16.48 T-FLG3047RG5 $ GT-3 LEFT T-FLG3047LA5 $16.48 T-FLG3047LA3 $16.48 T-FLG3047LG5 $ GT-3 RIGHT T-FLG3062RA5 $16.48 T-FLG3062RA3 $16.48 T-FLG3062RG5 $ GT-3 LEFT T-FLG3062LA5 $16.48 T-FLG3062LA3 $16.48 T-FLG3062LG5 $ GT-3 RIGHT T-FLG3072RA5 $16.48 T-FLG3072RA3 $16.48 T-FLG3072RG5 $ GT-3 LEFT T-FLG3072LA5 $16.48 T-FLG3072LA3 $16.48 T-FLG3072LG5 $ GT-3 RIGHT T-FLG3078RA5 $16.48 T-FLG3078RA3 $16.48 T-FLG3078RG5 $ GT-3 LEFT T-FLG3078LA5 $16.48 T-FLG3078LA3 $16.48 T-FLG3078LG5 $ GT-3 RIGHT T-FLG3088RA5 $16.48 T-FLG3088RA3 $16.48 T-FLG3088RG5 $ GT-3 LEFT T-FLG3088LA5 $16.48 T-FLG3088LA3 $16.48 T-FLG3088LG5 $ GT-3 RIGHT T-FLG3094RA5 $16.48 T-FLG3094RA3 $16.48 T-FLG3094RG5 $ GT-3 LEFT T-FLG3094LA5 $16.48 T-FLG3094LA3 $16.48 T-FLG3094LG5 $ GT-3 RIGHT T-FLG3097RA5 $16.48 T-FLG3097RA3 $16.48 T-FLG3097RG5 $ GT-3 LEFT T-FLG3097LA5 $16.48 T-FLG3097LA3 $16.48 T-FLG3097LG5 $ GT-3 RIGHT T-FLG3105RA5 $16.48 T-FLG3105RA3 $16.48 T-FLG3105RG5 $ GT-3 LEFT T-FLG3105LA5 $16.48 T-FLG3105LA3 $16.48 T-FLG3105LG5 $ GT-3 RIGHT T-FLG3110RA5 $16.48 T-FLG3110RA3 $16.48 T-FLG3110RG5 $ GT-3 LEFT T-FLG3110LA5 $16.48 T-FLG3110LA3 $16.48 T-FLG3110LG5 $ GT-3 RIGHT T-FLG3122RA5 $16.48 T-FLG3122RA3 $16.48 T-FLG3122RG5 $ GT-3 LEFT T-FLG3122LA5 $16.48 T-FLG3122LA3 $16.48 T-FLG3122LG5 $ GT-3 RIGHT T-FLG3125RA5 $16.48 T-FLG3125RA3 $16.48 T-FLG3125RG5 $ GT-3 LEFT T-FLG3125LA5 $16.48 T-FLG3125LA3 $16.48 T-FLG3125LG5 $ GT-3 RIGHT T-FLG3142RA5 $16.48 T-FLG3142RA3 $16.48 T-FLG3142RG5 $ GT-3 LEFT T-FLG3142LA5 $16.48 T-FLG3142LA3 $16.48 T-FLG3142LG5 $ GT-3 RIGHT T-FLG3156RA5 $16.48 T-FLG3156RA3 $16.48 T-FLG3156RG5 $ GT-3 LEFT T-FLG3156LA5 $16.48 T-FLG3156LA3 $16.48 T-FLG3156LG5 $ GT-3 RIGHT T-FLG3178RA5 $16.48 T-FLG3178RA3 $16.48 T-FLG3178RG5 $ GT-3 LEFT T-FLG3178LA5 $16.48 T-FLG3178LA3 $16.48 T-FLG3178LG5 $15.41 FULL LINE SUPPLIER Master Catalog 357 CARIDE INSERTS DEURRING

90 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD TOP NOTCH COMPATILE GROOVING INSERTS STANDARD GROOVING-DOULE ENDED INSERTS With Patented Chipbreaker Gage meter-series 2 Inserts: All Others: Full Line Available! Please call for more information. W Inch W mm E T A Toolholder/ oring ar GT GT GT GT GT GT GT GT GT GT GT GT-4 *Available in C3 uncoated grade. Please call for pricing. W Inch W mm E T A Toolholder/ oring ar GT-2 Left or Right Grades AT3, C3(Uncoated) Master Catalog Grade AT50 Grade GP50 RIGHT T-FLG2062RCA3* $16.48 T-FLG2062RCA5 $16.48 T-FLG2062RCG5 $15.41 LEFT T-FLG2062LCA3 $16.48 T-FLG2062LCA5 $16.48 T-FLG2062LCG5 $15.41 RIGHT T-FLG2094RCA3 $16.48 T-FLG2094RCA5 $16.48 T-FLG2094RCG5 $15.41 LEFT T-FLG2094LCA3 $16.48 T-FLG2094LCA5 $16.48 T-FLG2094LCG5 $15.41 RIGHT T-FLG2125RCA3 $16.48 T-FLG2125RCA5 $16.48 T-FLG2125RCG5 $15.41 LEFT T-FLG2125LCA3 $16.48 T-FLG2125LCA5 $16.48 T-FLG2125LCG5 $15.41 RIGHT T-FLG3062RCA3* $16.48 T-FLG3062RCA5 $16.48 T-FLG3062RCG5 $15.41 LEFT T-FLG3062LCA3 $16.48 T-FLG3062LCA5 $16.48 T-FLG3062LCG5 $15.41 RIGHT T-FLG3072RCA3 $16.48 T-FLG3072RCA5 $16.48 T-FLG3072RCG5 $15.41 LEFT T-FLG3072LCA3 $16.48 T-FLG3072LCA5 $16.48 T-FLG3072LCG5 $15.41 RIGHT T-FLG3078RCA3 $16.48 T-FLG3078RCA5 $16.48 T-FLG3078RCG5 $15.41 LEFT T-FLG3078LCA3 $16.48 T-FLG3078LCA5 $16.48 T-FLG3078LCG5 $15.41 RIGHT T-FLG3094RCA3 $16.48 T-FLG3094RCA5 $16.48 T-FLG3094RCG5 $15.41 LEFT T-FLG3094LCA3 $16.48 T-FLG3094LCA5 $16.48 T-FLG3094LCG5 $15.41 RIGHT T-FLG3125RCA3* $16.48 T-FLG3125RCA5 $16.48 T-FLG3125RCG5 $15.41 LEFT T-FLG3125LCA3* $16.48 T-FLG3125LCA5 $16.48 T-FLG3125LCG5 $15.41 RIGHT T-FLG3189RCA3 $16.48 T-FLG3189RCA5 $16.48 T-FLG3189RCG5 $15.41 LEFT T-FLG3189LCA3 $16.48 T-FLG3189LCA5 $16.48 T-FLG3189LCG5 $15.41 RIGHT T-FLG4125RCA3 $23.73 T-FLG4125RCA5 $23.73 T-FLG4125RCG5 $22.22 LEFT T-FLG4125LCA3 $23.73 T-FLG4125LCA5 $23.73 T-FLG4125LCG5 $22.22 RIGHT T-FLG4189RCA3 $23.73 T-FLG4189RCA5 $23.73 T-FLG4189RCG5 $22.22 LEFT T-FLG4189LCA3 $23.73 T-FLG4189LCA5 $23.73 T-FLG4189LCG5 $22.22 RIGHT T-FLG4250RCA3 $23.73 T-FLG4250RCA5 $23.73 T-FLG4250RCG5 $22.22 LEFT T-FLG4250LCA3 $23.73 T-FLG4250LCA5 $23.73 T-FLG4250LCG5 $22.22 STANDARD GROOVING-DOULE ENDED INSERTS-FULL NOSE RADIUS Gage meter-series 2 Inserts: All Others: GT GT GT GT GT GT GT GT GT GT-4 Left or Right Hand Grade AT50 Grade GP3 Grade GP50 RIGHT T-FLR2031RA5 $16.48 T-FLR2031RG3 $15.41 T-FLR2031RG5 $15.41 LEFT T-FLR2031LA5 $16.48 T-FLR2031LG3 $15.41 T-FLR2031LG5 $15.41 RIGHT T-FLR2047RA5 $16.48 T-FLR2047RG3 $15.41 T-FLR2047RG5 $15.41 LEFT T-FLR2047LA5 $16.48 T-FLR2047LG3 $15.41 T-FLR2047LG5 $15.41 RIGHT T-FLR2062RA5 $16.48 T-FLR2062RG3 $15.41 T-FLR2062RG5 $15.41 LEFT T-FLR2062LA5 $16.48 T-FLR2062LG3 $15.41 T-FLR2062LG5 $15.41 RIGHT T-FLR3031RA5 $16.48 T-FLR3031RG3 $15.41 T-FLR3031RG5 $15.41 LEFT T-FLR3031LA5 $16.48 T-FLR3031LG3 $15.41 T-FLR3031LG5 $15.41 RIGHT T-FLR3047RA5 $16.48 T-FLR3047RG3 $15.41 T-FLR3047RG5 $15.41 LEFT T-FLR3047LA5 $16.48 T-FLR3047LG3 $15.41 T-FLR3047LG5 $15.41 RIGHT T-FLR3062RA5 $16.48 T-FLR3062RG3 $15.41 T-FLR3062RG5 $15.41 LEFT T-FLR3062LA5 $16.48 T-FLR3062LG3 $15.41 T-FLR3062LG5 $15.41 RIGHT T-FLR3078RA5 $16.48 T-FLR3078RG3 $15.41 T-FLR3078RG5 $15.41 LEFT T-FLR3078LA5 $16.48 T-FLR3078LG3 $15.41 T-FLR3078LG5 $15.41 RIGHT T-FLR3094RA5 $16.48 T-FLR3094RG3 $15.41 T-FLR3094RG5 $15.41 LEFT T-FLR3094LA5 $16.48 T-FLR3094LG3 $15.41 T-FLR3094LG5 $15.41 RIGHT - - T-FLR4062RG3 $22.22 T-FLR4062RG5 $22.22 LEFT - - T-FLR4062LG3 $22.22 T-FLR4062LG5 $22.22 RIGHT - - T-FLR4094RG3 $22.22 T-FLR4094RG5 $22.22 LEFT - - T-FLR4094LG3 $22.22 T-FLR4094LG5 $22.22 RIGHT - - T-FLR4125RG3 $22.22 T-FLR4125RG5 $22.22 LEFT - - T-FLR4125LG3 $22.22 T-FLR4125LG5 $22.22

91 TOP NOTCH COMPATILE THREADING INSERTS THREADING-DOULE ENDED INSERTS ACME Threading Full Line Available! Please call for more information. TPI IF THREADING Internal External W Inches E T A Toolholder/ oring ar GT GT GT GT GT GT GT GT GT GT GT GT-6 THREADING-DOULE ENDED INSERTS ACME Stub Threading Gage meter: Internal TPI External W Inch E T A Left or Right Toolholder/ oring ar GT GT GT GT GT GT-3 60 V-THREADING-DOULE ENDED INSERTS TPI Internal External E T A Toolholder/ oring ar GT GT GT-4 Left or Right Hand Grade AT3 Grade AT50 Grade GP3 Grade GP50 RIGHT T-FLA3R16G5 $15.41 LEFT T-FLA3L16G5 $15.41 RIGHT T-FLA3R14G5 $15.41 LEFT T-FLA3L14G5 $15.41 RIGHT - - T-FLA3R12G3 $15.41 T-FLA3R12G5 $15.41 LEFT - - T-FLA3L12G3 $15.41 T-FLA3L12G5 $15.41 RIGHT - - T-FLA3R10G3 $ LEFT - - T-FLA3L10G3 $15.41 T-FLA3L10G5 $15.41 RIGHT T-FLA3R8A5 $16.48 T-FLA3R8G3 $15.41 T-FLA3R8G5 $15.41 LEFT T-FLA3L8A5 $16.48 T-FLA3L8G3 $15.41 T-FLA3L8G5 $15.41 RIGHT T-FLA3R6A5 $16.48 T-FLA3R6G3 $15.41 T-FLA3R6G5 $15.41 LEFT T-FLA3L6A5 $16.48 T-FLA3L6G3 $15.41 T-FLA3L6G5 $15.41 RIGHT T-FLA3R5A5 $16.48 T-FLA3R5G3 $15.41 T-FLA3R5G5 $15.41 LEFT T-FLA3L5A5 $16.48 T-FLA3L5G3 $15.41 T-FLA3L5G5 $15.41 RIGHT T-FLA3R4A5 $16.48 T-FLA3R4G3 $15.41 T-FLA3R4G5 $15.41 LEFT T-FLA3L4A5 $16.48 T-FLA3L4G3 $15.41 T-FLA3L4G5 $15.41 RIGHT T-FLA4R5G5 $22.22 LEFT T-FLA4L5G5 $22.22 RIGHT T-FLA4R4G5 $22.22 LEFT T-FLA4L4G5 $22.22 RIGHT T-FLA6R3G5 $30.07 LEFT T-FLA6L3G5 $30.07 RIGHT T-FLA6R2G5 $30.07 LEFT T-FLA6L2G5 $30.07 Left or Right Hand Grade AT50 Full Line Available! Please call for more information. Grade GP50 RIGHT - - T-FLAS3R12G5 $15.41 LEFT - - T-FLAS3L12G5 $15.41 RIGHT - - T-FLAS3R10G5 $15.41 LEFT - - T-FLAS3L10G5 $15.41 RIGHT T-FLAS3R8A5 $16.48 T-FLAS3R8G5 $15.41 LEFT T-FLAS3L8A5 $16.48 T-FLAS3L8G5 $15.41 RIGHT T-FLAS3R6A5 $16.48 T-FLAS3R6G5 $15.41 LEFT T-FLAS3L6A5 $16.48 T-FLAS3L6G5 $15.41 RIGHT T-FLAS3R5A5 $16.48 T-FLAS3R5G5 $15.41 LEFT T-FLAS3L5A5 $16.48 T-FLAS3L5G5 $15.41 RIGHT T-FLAS3R4A5 $16.48 T-FLAS3R4G5 $15.41 LEFT T-FLAS3L4A5 $16.48 T-FLAS3L4G5 $15.41 Grade AT50 Grade GP3 Grade GP50 RIGHT T-FLTF2RA3 $14.37 T-FLTF2RA5 $14.37 T-FLTF2RG3 $13.29 T-FLTF2RG5 $13.29 LEFT T-FLTF2LA3 $14.37 T-FLTF2LA5 $14.37 T-FLTF2LG3 $13.29 T-FLTF2LG5 $13.29 RIGHT T-FLTF3RA3 $14.37 T-FLTF3RA5 $14.37 T-FLTF3RG3 $13.87 T-FLTF3RG5 $13.87 LEFT T-FLTF3LA3 $14.37 T-FLTF3LA5 $14.37 T-FLTF3LG3 $13.87 T-FLTF3LG5 $13.87 RIGHT T-FLTF4RG3 $17.88 T-FLTF4RG5 $17.88 LEFT T-FLTF4LG3 $17.88 T-FLTF4LG5 $ Master Catalog 359 CARIDE INSERTS DEURRING

92 CHUCK JAWS LATHE WORKHOLDING TOP NOTCH COMPATILE THREADING INSERTS THREADING-DOULE ENDED INSERTS UN Crest Topping Threading Gage meter: MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING TPI Internal External E R T A Toolholder/ oring ar Left/ Right Hand Grade AT3 Grade GP3 Grade GP GT-3 RIGHT T-FLTC3R7EA3 $ T-FLTC3R7EG5 $ GT GT-3 RIGHT T-FLTC3R8EA3 $15.47 T-FLTC3R8EG T-FLTC3R8EG5 $14.40 LEFT T-FLTC3L8EA3 $ T-FLTC3L8EG5 $14.40 RIGHT T-FLTC3R8IG5 $14.40 LEFT T-FLTC3L8IA3 $ T-FLTC3L8IG5 $ GT-3 RIGHT T-FLTC3R9EA3 $ T-FLTC3R9EG5 $ GT GT-3 RIGHT T-FLTC3R10EA3 $15.47 T-FLTC3R10EG3 $14.40 T-FLTC3R10EG5 $14.40 LEFT T-FLTC3L10EA3 $ T-FLTC3L10EG5 $14.40 RIGHT T-FLTC3R10IG5 $14.40 LEFT T-FLTC3L10IA3 $ T-FLTC3L10IG5 $ GT-3 RIGHT T-FLTC3R11EA3 $ T-FLTC3R11EG5 $ GT GT GT GT GT GT GT GT-3 RIGHT T-FLTC3R12EA3 $ T-FLTC3R12EG5 $14.40 LEFT T-FLTC3L12EG5 $14.40 RIGHT - - T-FLTC3R12IG3 $ LEFT T-FLTC3L12IA3 $ T-FLTC3L12IG5 $14.40 RIGHT T-FLTC3R14EG5 $14.40 LEFT T-FLTC3L14EA3 $ T-FLTC3L14EG5 $14.40 RIGHT T-FLTC3R14IG5 $14.40 LEFT T-FLTC3L14IA3 $ T-FLTC3L14IG5 $14.40 RIGHT - - T-FLTC3R16EG3 $14.40 T-FLTC3R16EG5 $14.40 LEFT - - T-FLTC3L16EG3 $14.40 T-FLTC3L16EG5 $14.40 RIGHT T-FLTC3R16IG5 $14.40 LEFT T-FLTC3L16IA3 $ T-FLTC3L16IG5 $14.40 RIGHT - - T-FLTC3R18EG3 $14.40 T-FLTC3R18EG5 $14.40 LEFT T-FLTC3L18EA3 $ T-FLTC3L18EG5 $14.40 RIGHT - - T-FLTC3R20EG3 $14.40 T-FLTC3R20EG5 $14.40 LEFT T-FLTC3L20EA3 $ T-FLTC3L20EG5 $ GT-3 LEFT T-FLTC3L20IG5 $ GT-3 RIGHT - - T-FLTC3R24EG3 $14.40 T-FLTC3R24EG5 $ V-THREADING DOULE ENDED INSERTS ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Internal Ext. E T A TPI Toolholder/ oring ar Left or Right Hand Grade AT3 Grade AT Master Catalog Grade GP3 Grade GP50, GV rand C5 (TIN Coat) GT-2 RIGHT T-FLT2RA3 $13.83 T-FLT2RA5 $13.83 T-FLT2RG3 $12.80 T-FLT2RG5 $ GT-2 LEFT T-FLT2LA3 $13.83 T-FLT2LA5 $13.83 T-FLT2LG3 $12.80 T-FLT2LG5 $ GT-3 RIGHT T-FLT3RA3 $13.83 T-FLT3RA5 $13.83 T-FLT3RG3 $13.33 T-FLT3RG5 $ GT-3 LEFT T-FLT3LA3 $13.83 T-FLT3LA5 $13.83 T-FLT3LG3 $13.33 T-FLT3LG5 $ GT-4 RIGHT T-FLT4RA3 $17.96 T-FLT4RA5 $17.96 T-FLT4RG3 $16.56 T-FLT4RG5 $ GT-4 LEFT T-FLT4LA3 $17.96 T-FLT4LA5 $17.96 T-FLT4LG3 $16.56 T-FLT4LG5 $ V THREADING - DOULE ENDED, POSITIVE RAKE Internal External E T A Toolholder/ oring ar GT GT GT-4 Left or Right Hand Grade AT3 Grade AT50 Grade GP3 Grade GP50 RIGHT T-FLTP2RA3 $14.34 T-FLTP2RA5 $14.34 T-FLTP2RG3 $13.29 T-FLTP2RG5 $13.29 LEFT - - T-FLTP2LA5 $14.34 T-FLTP2LG3 $13.29 T-FLTP2LG5 $13.29 RIGHT T-FLTP3RA3 $14.92 T-FLTP3RA5 $14.92 T-FLTP3RG3 $13.87 T-FLTP3RG5 $13.87 LEFT T-FLTP3LA3 $14.92 T-FLTP3LA5 $14.92 T-FLTP3LG3 $13.87 T-FLTP3LG5 $13.87 RIGHT T-FLTP4RA3 $ T-FLTP4RG3 $17.88 T-FLTP4RG5 $17.88 LEFT T-FLTP4LA3 $ T-FLTP4LG3 $17.88 T-FLTP4LG5 $17.88

93 TOP NOTCH COMPATILE THREADING HOLDERS EXTERNAL SQUARE SHANK HOLDERS Full Line Available! Please call for more information. Style GT-2 GT-3 GT-2 GT-3 GT-4 GT-3 GT-4 GT-5 For Use With Insert Hand A C D F ToolFlo Dorian Canela RIGHT T-FLSR-82V $ RIGHT DN-NSR10-2 $ LEFT DN-NSL10-2 $ RIGHT T-FLSR-122 $70.89 DN-NSR12-2 $ LEFT T-FLSL-122 $72.07 DN-NSL12-2 $ RIGHT DN-NSR12-3A $ LEFT DN-NSL12-3A $ RIGHT T-FLSR-123 $72.07 DN-NSR12-3 $91.03 CA-CLSR12-3 $86.00 LEFT T-FLSL-123 $72.07 DN-NSL12-3 $91.03 CA-CLSL12-3 $86.00 RIGHT T-FLSR-162C $73.23 DN-NSR16-2C $ LEFT T-FLSL-162C $73.23 DN-NSL16-2C $ RIGHT T-FLSR-163C $73.23 DN-NSR16-3C $ LEFT T-FLSL-163C $73.23 DN-NSL16-3C $ RIGHT T-FLSR-163D $73.23 DN-NSR16-3D $92.36 CA-CLSR16-3D $87.34 LEFT T-FLSL-163D $73.23 DN-NSL16-3D $92.36 CA-CLSL16-3D $87.34 RIGHT DN-NSR16-4C $ LEFT DN-NSL16-4C $ RIGHT T-FLSR-164D $73.23 DN-NSR16-4D $92.36 CA-CLSR16-4D $87.34 LEFT T-FLSL-164D $73.23 DN-NSL16-4D $92.36 CA-CLSL16-4D $87.34 RIGHT T-FLSR-203D $ CA-CLSR20-3D $99.43 LEFT T-FLSL-203D $ CA-CLSL20-3D $99.43 RIGHT T-FLSR-204D $80.24 DN-NSR20-4D $ CA-CLSR20-4D $99.43 LEFT T-FLSL-204D $80.24 DN-NSL20-4D $ CA-CLSL20-4D $99.43 RIGHT T-FLSR-205D $ LEFT T-FLSL-205D $ EXTERNAL SQUARE SHANK HOLDERS Uses opposite hand inserts. Right hand holder uses left hand inserts. Style Style GT-2 GT-3 GT-4 Left or Right Left or Right A C D F H INTERNAL ORING ARS Uses opposite hand inserts. Right hand bar uses left hand inserts. GT-2 GT-3 GT-4 ToolFlo Dorian RIGHT T-FLER-162C $ LEFT T-FLEL-162C $ RIGHT T-FLER-123 $72.07 DN-NER12-3 $91.03 LEFT T-FLEL-123 $72.07 DN-NEL12-3 $91.03 RIGHT T-FLER-163D $73.23 DN-NER16-3D $92.36 LEFT T-FLEL-163D $73.23 DN-NEL16-3D $92.36 RIGHT T-FLER-203D $ LEFT T-FLEL-203D $ RIGHT T-FLER-164D $73.23 DN-NER16-4D $92.36 LEFT T-FLEL-164D $73.23 DN-NEL16-4D $92.36 RIGHT T-FLER-204D $ LEFT T-FLEL-204D $ Min. ore C D F ToolFlo Dorian Canela RIGHT T-A10-FLER2 $ DN-S10S-NER-2 $ LEFT T-A10-FLEL2 $ DN-S10S-NEL-2 $ RIGHT T-A12-FLER2 $ DN-S12S-NER-2 $ LEFT T-A12-FLEL2 $ DN-S12S-NEL-2 $ RIGHT T-A16-FLER2 $ LEFT T-A16-FLEL2 $ RIGHT T-A16-FLER3 $ DN-S16T-NER-3 $ CA-A16T-CLER3 $ LEFT T-A16-FLEL3 $ DN-S16T-NEL-3 $ CA-A16T-CLEL3 $ RIGHT T-A20-FLER3 $ DN-S20U-NER-3 $ CA-A20U-CLER3 $ LEFT T-A20-FLEL3 $ DN-S20U-NEL-3 $ CA-A20U-CLEL3 $ RIGHT T-A24-FLER3 $ DN-S24U-NER-3 $ LEFT T-A24-FLEL3 $ DN-S24U-NEL-3 $ RIGHT T-A28-FLER3 $ CA-A28U-CLER3 $ LEFT CA-A28U-CLEL3 $ RIGHT T-A32-FLER3 $ CA-A32V-CLER3 $ LEFT T-A32-FLEL3 $ CA-A32V-CLEL3 $ RIGHT DN-S28U-NER-4 $ CA-A28U-CLER4 $ LEFT DN-S28U-NEL-4 $ CA-A28U-CLEL4 $ RIGHT T-A32-FLER4 $ DN-S32V-NER-4 $ CA-A32V-CLER4 $ LEFT T-A32-FLEL4 $ DN-S32V-NEL-4 $ CA-A32V-CLEL4 $ Master Catalog 361 CARIDE INSERTS DEURRING

94 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS T-SERIES LAYDOWN GROOVING INSERTS GROOVING INSERTS Full Line Available! Please call for more information. THREADING INSERTS T SERIES LAYDOWN - EXTERNAL GROOVING INSERTS W IC D L (3/8) (3/8) (3/8) For Use With Holder Left or Right Grade GP ER RIGHT T-16ERNGW47G50 $ ER RIGHT T-16ERNGW62G50 $ ER RIGHT T-16ERNGW93G50 $12.41 T SERIES LAYDOWN - INTERNAL GROOVING INSERTS W IC D L (3/8) (3/8) (3/8) For Use With Holder Left or Right Grade GP NR RIGHT T-16NRNGW47G50 $ NR RIGHT T-16NRNGW62G50 $ NR RIGHT T-16NRNGW93G50 $12.41 TOOLHOLDERS T SERIES LAYDOWN - EXTERNAL THREADING INSERTS Full Line Available! Please call for more information. INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD TPI If Threading IC oth Threading & Grooving L oth Threading & Grooving IF THREADING M K R For Use With Holder Left or Right Grade AT Master Catalog Grade GP22 Grade GP / ER RIGHT T-16ERA60A2 $12.41 T-16ERA60G22 $12.41 T-16ERA60G50 $ EL LEFT T-16ELA60A2 $ / ER RIGHT T-16ERAG60A2 $12.41 T-16ERAG60G22 $12.41 T-16ERAG60G50 $ EL LEFT T-16ELAG60A2 $ / EL LEFT T-16ELG60A2 $ / ER RIGHT T-22ERN60G50 $17.32 T SERIES LAYDOWN - INTERNAL THREADING INSERTS TPI If Threading Full Line Available! Please call for more information. IC oth Threading & Grooving L oth Threading & Grooving IF THREADING M K R / / / / For Use With Holder Left or Right Grade AT22 Grade GP22 Grade GP50 16NR RIGHT T-16NRA60G50 $ NL LEFT T-16NLA60G50 16NR RIGHT T-16NRAG60A2 $12.41 T-16NRAG60G22 $12.41 T-16NRAG60G50 $ NL LEFT T-16NLAG60G50 $ NR RIGHT - - T-16NRG60G22 $12.41 T-16NRG60G50 $ NL LEFT T-16NLG60G50 $ NR RIGHT - - T-22NRN60G22 $17.32 T-22NRN60G50 $ NL LEFT T-22NLN60G50 $17.32

95 T-SERIES LAYDOWN THREADING HOLDERS INTERNAL & EXTERNAL THREADING HOLDERS GRADE INFORMATION T SERIES LAYDOWN EXTERNAL THREADING HOLDERS For Use With Holder 16ER Left or Right A C E F RIGHT T-AL075-3R $83.81 RIGHT T-AL100-3R $ ER RIGHT T-AL100-4R $ EL LEFT T-AL100-4L $ ER RIGHT T-AL125-5R $95.51 T SERIES LAYDOWN INTERNAL THREADING HOLDERS For Use With Holder 16NR 22NR Left or Right Min ore For oring ars C D F L RIGHT T-NVR625-3R $98.03 RIGHT T-AVR750-3R $ RIGHT T-AVR100-3R $ RIGHT T-AVR125-3R $ RIGHT T-AVR150-3R $ RIGHT T-NVR750-4R $98.03 RIGHT T-AVR100-4R $ Grade Class Description Material Application GP4 GP22 GP3 AT3 C1/C5A K30/P30 C1 K30 C3 K15-K25 M05-M20 Coated - Sub-Micron Coated - Sub-Micron Coated - Sub-Micron Coated - Sub-Micron Aluminum, Cast Iron, 300/400 Stainless Steel, Non-Metals, Carbon/Alloy Steel, Ductile Iron, Chrome Aluminum, Cast Iron, 300 Stainless Steel, High Temp Alloys, Non-Metals, Chrome High Temp Alloys, 300 Stainless Steel TiAln Coated For High Temp Alloys & 300 Series Stainless Steel GP50 C5 Coated Carbon/Alloy Steel, 400 Stainless Steel, Ductile Iron AT50 P20-P35 M15-M30 Coated TiAln Coated For 400 Series Stainless Steel & Ductile Cast Iron Extremely tough grades that perform well at very slow SFPM with minimal breakage or chipping. Extremely tough grades that perform well at very slow SFPM with minimal breakage or chipping. Versatile grades that combine high hardness with toughness - General purpose grades, coated grades can normally be ran at higher SFPM C3 C2-C3 Coated Non Ferrous Metals, Plastics - - CARIDE INSERTS DEURRING Full Line Available! Please call for more information Master Catalog 363

96 CHUCK JAWS LATHE WORKHOLDING THREAD TURNING INSERTS PARTIAL PROFILE 60 INSERTS For Unified (UN-American) and Metric (ISO) Thread Forms C MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS Insert Series Pitch Range EXTERNAL INTERNAL I.C. TPI MM X Y Right Hand Left Hand Right Hand Left Hand 6 5/ T-C06IRA60 T-C06ILA60 $ / T-C08IRA60 T-C08ILA60 $ U 3/16U T-C08IRLU60 T-C08IRLU60 $ / T-C11ERA60 T-C11ELA60 T-C11IRA60 T-C11ILA60 $ / T-C16ERA60 T-C16ELA60 T-C16IRA60 T-C16ILA60 $ / T-C16ERG60 T-C16ELG60 T-C16IRG60 T-C16ILG60 $ / T-C16ERAG60 T-C16ELAG60 T-C16IRAG60 T-C16ILAG60 $ / T-C22ERN60 T-C22ELN60 T-C22IRN60 T-C22ILN60 $ U 1/2U T-C22UEIRLU60 T-C22UEIRLU60 T-C22UEIRLU60 T-C22UEIRLU60 $ / T-C27ERQ60 T-C27ELQ60 T-C27IRQ60 T-C27ILQ60 $ U 5/8U T-C27UEIRLU60 T-C27UEIRLU60 T-C27UEIRLU60 T-C27UEIRLU60 $24.38 ial Profile 60 - W/ Sintered Chipbreaker Insert Series 16 I.C. TPI MM X Y Right Hand Left Hand Right Hand Left Hand 3/ T-C16ERA60 T-C16ELA60 T-C16IRA60 T-C16ILA60 $ / T-C16ERG60 T-C16ELG60 T-C16IRG60 T-C16ILG60 $ / T-C16ERAG60 T-C16ELAG60 T-C16IRAG60 T-C16ILAG60 $12.95 PARTIAL PROFILE 55 INSERTS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD INSERT SERIES Pitch Range EXTERNAL INTERNAL I.C. TPI MM X Y Right Hand Left Hand Master Catalog Right Hand Left Hand 6 5/ T-C06IRA55 T-C06ILA55 $ / T-C08IRA55 T-C08ILA55 $ U 3/16U T-C08IRLU55 T-C08IRLU55 $ / T-C11ERA55 T-C11ELA55 T-C11IRA55 T-C11ILA55 $ / T-C16ERA55 T-C16ELA55 T-C16IRA55 T-C16ILA55 $ / T-C16ERG55 T-C16ELG55 T-C16IRG55 T-C16ILG55 $ / T-C16ERAG55 T-C16ELAG55 T-C16IRAG55 T-C16ILAG55 $ / T-C22ERN55 T-C22ELN55 T-C22IRN55 T-C22ILN55 $ U 1/2U T-C22UEIRLU55 T-C22UEIRLU55 T-C22UEIRLU55 T-C22UEIRLU55 $ / T-C27ERQ55 T-C27ELQ55 T-C27IRQ55 T-C27ILQ55 $ U 5/8U T-C27UEIRLU55 T-C27UEIRLU55 T-C27UEIRLU55 T-C27UEIRLU55 $24.38 ial Profile 55 W/ Chipbreaker INSERT SERIES 16 I.C. TPI MM X Y Right Hand Left Hand Right Hand Left Hand 3/ T-C16ERG55 T-C16ELG55 T-C16IRG55 T-C16ILG55 $ / T-C16ERAG55 T-C16ELAG55 T-C16IRAG55 T-C16ILAG55 $12.95 How To Order: 1) Pick the required insert from table above eg: T-C11ERA60 2) Pick a Carbide grade from the Grades table below - eg. 4 for superalloys and stainless steels 3) Order T-C11ERA604 4) Pick toolholder (ext) or boring bar (int) from pages Carmex Grade USST Grade CARMEX GRADE INFORMATION Carbide ANSI Coating Full Line Available! Please call for more information. Materials P25C P5 C5 TIN Hard Steels MXC M2 C2-C3 TIN Soft Steels, Stainless Steels, Cast Iron MA 4 C3-C4 TIALN Superalloys, Stainless Steels K20 K2 C2 UNCOATED Aluminum, Non Ferrous

97 LAYDOWN THREAD TURNING INSERTS ISO METRIC FULL PROFILE INSERTS For Metric Threads, ISO 262, DIN 13 ISO METRIC - Full Profile For Metric Threads, ISO 262, DIN 13 INSERT SERIES I.C. Pitch MM X Y EXTERNAL Right Hand Left Hand INTERNAL Right Hand X Y Left Hand 5/ T-C06IR05M T-C06IL05M $ / T-C06IR075M T-C06IL075M $ / T-C06IR10M T-C06IL10M $ / T-C06IR125M T-C06IL125M $ / T-C08IR05M T-C08IL05M $ / T-C08IR075M T-C08IL075M $ / T-C08IR10M T-C08IL10M $ / T-C08IR125M T-C08IL125M $ / T-C08IR15M T-C08IL15M $ / T-C08IR175M T-C08IL175M $ / T-C11ER035M T-C11EL035M T-C11IR035M T-C11IL035M $ / T-C11ER04M T-C11EL04M T-C11IR04M T-C11IL04M $ / T-C11ER045M T-C11EL045M T-C11IR045M T-C11IL045M $ / T-C11ER05M T-C11EL05M T-C11IR05M T-C11IL05M $ / T-C11ER06M T-C11EL06M T-C11IR06M T-C11IL06M $ / T-C11ER07M T-C11EL07M T-C11IR07M T-C11IL07M $ / T-C11ER075M T-C11EL075M T-C11IR075M T-C11IL075M $ / T-C11ER08M T-C11EL08M T-C11IR08M T-C11IL08M $ / T-C11ER10M T-C11EL10M T-C11IR10M T-C11IL10M $ / T-C11ER125M T-C11EL125M T-C11IR125M T-C11IL125M $ / T-C11ER15M T-C11EL15M T-C11IR15M T-C11IL15M $ / T-C11ER175M T-C11EL175M T-C11IR175M T-C11IL175M $ / T-C11IR20M T-C11IL20M $ / T-C16ER035M T-C16EL035M T-C16IR035M T-C16IL035M $ / T-C16ER04M T-C16EL04M T-C16IR04M T-C16IL04M $ / T-C16ER045M T-C16EL045M T-C16IR045M T-C16IL045M $ / T-C16ER05M T-C16EL05M T-C16IR05M T-C16IL05M $ / T-C16ER06M T-C16EL06M T-C16IR06M T-C16IL06M $ / T-C16ER07M T-C16EL07M T-C16IR07M T-C16IL07M $ / T-C16ER075M T-C16EL075M T-C16IR075M T-C16IL075M $ / T-C16ER08M T-C16EL08M T-C16IR08M T-C16IL08M $ / T-C16ER10M T-C16EL10M T-C16IR10M T-C16IL10M $ / T-C16ER125M T-C16EL125M T-C16IR125M T-C16IL125M $ / T-C16ER15M T-C16EL15M T-C16IR15M T-C16IL15M $ / T-C16ER175M T-C16EL175M T-C16IR175M T-C16IL175M $ / T-C16ER20M T-C16EL20M T-C16IR20M T-C16IL20M $ / T-C16ER25M T-C16EL25M T-C16IR25M T-C16IL25M $ / T-C16ER30M T-C16EL30M T-C16IR30M T-C16IL30M $ / T-C22ER35M T-C22EL35M T-C22IR35M T-C22IL35M $ / T-C22ER40M T-C22EL40M T-C22IR40M T-C22IL40M $ / T-C22ER45M T-C22EL45M T-C22IR45M T-C22IL45M $ / T-C22ER50M T-C22EL50M T-C22IR50M T-C22IL50M $ U 1/2U T-C22UERL55M T-C22UERL55M T-C22UIRL55M T-C22UIRL55M $ /2U T-C22UERL60M T-C22UERL60M T-C22UIRL60M T-C22UIRL60M $ / T-C27ER55M T-C27EL55M T-C27IR55M T-C27IL55M $ / T-C27ER60M T-C27EL60M T-C27IR60M T-C27IL60M $ U 5/8U T-C27UERL80M T-C27UERL80M T-C27UIRL80M T-C27UIRL80M $24.38 ISO METRIC - Full Profile W/SINTERED CHIPREAKER 3/ T-C16ER08M T-C16EL08M / T-C16ER10M T-C16EL10M T-C16IR10M T-C16IL10M $ / T-C16ER125M T-C16EL125M T-C16IR125M T-C16IL125M $ / T-C16ER15M T-C16EL15M T-C16IR15M T-C16IL15M $ / T-C16ER175M T-C16EL175M T-C16IR175M T-C16IL175M $ / T-C16ER20M T-C16EL20M T-C16IR20M T-C16IL20M $ / T-C16ER25M T-C16EL25M T-C16IR25M T-C16IL25M $ / T-C16ER30M T-C16EL30M T-C16IR30M T-C16IL30M $ Master Catalog 365 C How To Order: 1) Pick the required insert from table above eg: T-C11ERA60 2) Pick a Carbide grade from the Grades table 4 for superalloys and stainless steels 3) Order T-C11ERA604 4) Pick toolholder (ext) or boring bar (int) from pages CARIDE INSERTS DEURRING

98 CHUCK JAWS LATHE WORKHOLDING LAYDOWN THREAD TURNING INSERTS UN FULL PROFILE INSERTS For American Unified 60 Threads ANSI 1.1:74 Full Line Available! Please call for more information. C MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD INSERT SERIES I.C. Pitch TPI X Y EXTERNAL Right Hand Left Hand Master Catalog X Y INTERNAL Right Hand Left Hand 5/ T-C06IR32UN T-C06IL32UN $ / T-C06IR28UN T-C06IL28UN $ / T-C06IR24UN T-C06IL24UN $ / T-C06IR20UN T-C06IL20UN $ / T-C06IR18UN T-C06IL18UN $ / T-C08IR32UN T-C08IL32UN $ / T-C08IR28UN T-C08IL28UN $ / T-C08IR24UN T-C08IL24UN $ / T-C08IR20UN T-C08IL20UN $ / T-C08IR18UN T-C08IL18UN $ / T-C08IR16UN T-C08IL16UN $ / T-C08IR14UN T-C08IL14UN $ /16U T-C08UIRL13UN T-C08UIRL13UN $ U 3/16U T-C08UIRL12UN T-C08UIRL12UN $ /16U T-C08UIRL11UN T-C08UIRL11UN $ / T-C11ER72UN T-C11EL72UN T-C11IR72UN T-C11IL72UN $ / T-C11ER64UN T-C11EL64UN T-C11IR64UN T-C11IL64UN $ / T-C11ER56UN T-C11EL56UN T-C11IR56UN T-C11IL56UN $ / T-C11ER48UN T-C11EL48UN T-C11IR48UN T-C11IL48UN $ / T-C11ER44UN T-C11EL44UN T-C11IR44UN T-C11IL44UN $ / T-C11ER40UN T-C11EL40UN T-C11IR40UN T-C11IL40UN $ / T-C11ER36UN T-C11EL36UN T-C11IR36UN T-C11IL36UN $ / T-C11ER32UN T-C11EL32UN T-C11IR32UN T-C11IL32UN $ / T-C11ER28UN T-C11EL28UN T-C11IR28UN T-C11IL28UN $ / T-C11ER27UN T-C11EL27UN T-C11IR27UN T-C11IL27UN $ / T-C11ER24UN T-C11EL24UN T-C11IR24UN T-C11IL24UN $ / T-C11ER20UN T-C11EL20UN T-C11IR20UN T-C11IL20UN $ / T-C11ER18UN T-C11EL18UN T-C11IR18UN T-C11IL18UN $ / T-C11ER16UN T-C11EL16UN T-C11IR16UN T-C11IL16UN $ / T-C11ER14UN T-C11EL14UN T-C11IR14UN T-C11IL14UN $ / T-C11IR13UN T-C11IL13UN $ / T-C11IR12UN T-C11IL12UN $ / T-C11IR11UN T-C11IL11UN $ / T-C16ER72UN T-C16EL72UN T-C16IR72UN T-C16IL72UN $ / T-C16ER64UN T-C16EL64UN T-C16IR64UN T-C16IL64UN $ / T-C16ER56UN T-C16EL56UN T-C16IR56UN T-C16IL56UN $ / T-C16ER48UN T-C16EL48UN T-C16IR48UN T-C16IL48UN $ / T-C16ER44UN T-C16EL44UN T-C16IR44UN T-C16IL44UN $ / T-C16ER40UN T-C16EL40UN T-C16IR40UN T-C16IL40UN $ / T-C16ER36UN T-C16EL36UN T-C16IR36UN T-C16IL36UN $ / T-C16ER32UN T-C16EL32UN T-C16IR32UN T-C16IL32UN $ / T-C16ER28UN T-C16EL28UN T-C16IR28UN T-C16IL28UN $ / T-C16ER27UN T-C16EL27UN T-C16IR27UN T-C16IL27UN $ / T-C16ER24UN T-C16EL24UN T-C16IR24UN T-C16IL24UN $ / T-C16ER20UN T-C16EL20UN T-C16IR20UN T-C16IL20UN $ / T-C16ER18UN T-C16EL18UN T-C16IR18UN T-C16IL18UN $ / T-C16ER16UN T-C16EL16UN T-C16IR16UN T-C16IL16UN $ / T-C16ER14UN T-C16EL14UN T-C16IR14UN T-C16IL14UN $ / T-C16ER13UN T-C16EL13UN T-C16IR13UN T-C16IL13UN $ / T-C16ER12UN T-C16EL12UN T-C16IR12UN T-C16IL12UN $ / T-C16ER115UN T-C16EL115UN T-C16IR115UN T-C16IL115UN $ / T-C16ER11UN T-C16EL11UN T-C16IR11UN T-C16IL11UN $ / T-C16ER10UN T-C16EL10UN T-C16IR10UN T-C16IL10UN $ / T-C16ER9UN T-C16EL9UN T-C16IR9UN T-C16IL9UN $ / T-C16ER8UN T-C16EL8UN T-C16IR8UN T-C16IL8UN $ / T-C22ER7UN T-C22EL7UN T-C22IR7UN T-C22IL7UN $ / T-C22ER6UN T-C22EL6UN T-C22IR6UN T-C22IL6UN $ / T-C22ER5UN T-C22EL5UN T-C22IR5UN T-C22IL5UN $ U 1/2U T-C22UERL45UN T-C22UERL45UN T-C22UIRL45UN T-C22UIRL45UN $ /2U T-C22UERL4UN T-C22UERL4UN T-C22UIRL4UN T-C22UIRL4UN $ / T-C27ER45UN T-C27EL45UN T-C27IR45UN T-C27IL45UN $ / T-C27ER4UN T-C27EL4UN T-C27IR4UN T-C27IL4UN $ U 5/8U T-C27UERL3UN T-C27UERL3UN T-C27UIRL3UN T-C27UIRL3UN $24.38

99 LAYDOWN THREAD TURNING INSERTS UN FULL PROFILE INSERTS With Sintered Chipbreaker For American Unified 60 Threads ANSI 1.1:74 C INSERT SERIES 16 EXTERNAL INTERNAL I.C. PITCH Right Hand Left Hand Right Hand Left Hand X Y X Y TPI 3/ T-C16ER24UN T-C16EL24UN T-C16IR24UN T-C16IL24UN $ / T-C16ER20UN T-C16EL20UN T-C16IR20UN T-C16IL20UN $ / T-C16ER18UN T-C16EL18UN T-C16IR18UN T-C16IL18UN $ / T-C16ER16UN T-C16EL16UN T-C16IR16UN T-C16IL16UN $ / T-C16ER14UN T-C16EL14UN T-C16IR14UN T-C16IL14UN $ / T-C16ER13UN T-C16EL13UN $ / T-C16ER12UN T-C16EL12UN T-C16IR12UN T-C16IL12UN $ / T-C16ER11UN T-C16EL11UN $ / T-C16ER10UN T-C16EL10UN T-C16IR10UN T-C16IL10UN $ / T-C16ER9UN T-C16EL9UN $ / T-C16ER8UN T-C16EL8UN T-C16IR8UN T-C16IL8UN $12.95 UNJ, UNJC, UNJF, UNJEF, UNJS INSERTS Aerospace Threads-Controlled Root Radius INSERT SERIES I.C. PITCH TPI X Y Right Hand EXTERNAL Left Hand Right Hand INTERNAL Left Hand 1/ T-C11ER48UNJ T-C11EL48UNJ T-C11IR48UNJ T-C11IL48UNJ $ / T-C11ER44UNJ T-C11EL44UNJ T-C11IR44UNJ T-C11IL44UNJ $ / T-C11ER40UNJ T-C11EL40UNJ T-C11IR40UNJ T-C11IL40UNJ $ / T-C11ER36UNJ T-C11EL36UNJ T-C11IR36UNJ T-C11IL36UNJ $ / T-C11ER32UNJ T-C11EL32UNJ T-C11IR32UNJ T-C11IL32UNJ $ / T-C11ER28UNJ T-C11EL28UNJ T-C11IR28UNJ T-C11IL28UNJ $ / T-C11ER24UNJ T-C11EL24UNJ T-C11IR24UNJ T-C11IL24UNJ $ / T-C11ER20UNJ T-C11EL20UNJ T-C11IR20UNJ T-C11IL20UNJ $ / T-C11ER18UNJ T-C11EL18UNJ T-C11IR18UNJ T-C11IL18UNJ $ / T-C11ER16UNJ T-C11EL16UNJ T-C11IR16UNJ T-C11IL16UNJ $ / T-C11ER14UNJ T-C11EL14UNJ T-C11IR14UNJ T-C11IL14UNJ $ / T-C16ER48UNJ T-C16EL48UNJ T-C16IR48UNJ T-C16IL48UNJ $ / T-C16ER44UNJ T-C16EL44UNJ T-C16IR44UNJ T-C16IL44UNJ $ / T-C16ER40UNJ T-C16EL40UNJ T-C16IR40UNJ T-C16IL40UNJ $ / T-C16ER36UNJ T-C16EL36UNJ T-C16IR36UNJ T-C16IL36UNJ $ / T-C16ER32UNJ T-C16EL32UNJ T-C16IR32UNJ T-C16IL32UNJ $ / T-C16ER28UNJ T-C16EL28UNJ T-C16IR28UNJ T-C16IL28UNJ $ / T-C16ER24UNJ T-C16EL24UNJ T-C16IR24UNJ T-C16IL24UNJ $ / T-C16ER20UNJ T-C16EL20UNJ T-C16IR20UNJ T-C16IL20UNJ $ / T-C16ER18UNJ T-C16EL18UNJ T-C16IR18UNJ T-C16IL18UNJ $ / T-C16ER16UNJ T-C16EL16UNJ T-C16IR16UNJ T-C16IL16UNJ $ / T-C16ER14UNJ T-C16EL14UNJ T-C16IR14UNJ T-C16IL14UNJ $ / T-C16ER13UNJ T-C16EL13UNJ T-C16IR13UNJ T-C16IL13UNJ $ / T-C16ER12UNJ T-C16EL12UNJ T-C16IR12UNJ T-C16IL12UNJ $ / T-C16ER11UNJ T-C16EL11UNJ T-C16IR11UNJ T-C16IL11UNJ $ / T-C16ER10UNJ T-C16EL10UNJ T-C16IR10UNJ T-C16IL10UNJ $ / T-C16ER9UNJ T-C16EL9UNJ T-C16IR9UNJ T-C16IL9UNJ $ / T-C16ER8UNJ T-C16EL8UNJ T-C16IR8UNJ T-C16IL8UNJ $ Master Catalog 367 CARIDE INSERTS DEURRING

100 CHUCK JAWS LATHE WORKHOLDING LAYDOWN THREAD TURNING INSERTS NPT-S 2.1:1968 INSERTS C MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INSERT SERIES I.C. PITCH TPI X Y Right Hand EXTERNAL Left Hand Right Hand INTERNAL Left Hand 6 5/ T-C06IR27NPT T-C06IL27NPT $ / T-C08IR27NPT T-C08IL27NPT $ / T-C08IR18NPT T-C08IL18NPT $ / T-C11ER27NPT T-C11EL27NPT T-C11IR27NPT T-C11IL27NPT $ / T-C11ER18NPT T-C11EL18NPT T-C11IR18NPT T-C11IL18NPT $ / T-C11ER14NPT T-C11EL14NPT T-C11IR14NPT T-C11IL14NPT $ / T-C16ER27NPT T-C16EL27NPT T-C16IR27NPT T-C16IL27NPT $ / T-C16ER18NPT T-C16EL18NPT T-C16IR18NPT T-C16IL18NPT $ / T-C16ER14NPT T-C16EL14NPT T-C16IR14NPT T-C16IL14NPT $ / T-C16ER115NPT T-C16EL115NPT T-C16IR115NPT T-C16IL115NPT $ / T-C16ER8NPT T-C16EL8NPT T-C16IR8NPT T-C16IL8NPT $12.95 NPT / W CHIPREAKER 3/ T-C16ER18NPT T-C16EL18NPT - - $ / T-C16ER14NPT T-C16EL14NPT T-C16IR14NPT T-C16IL14NPT $ / T-C16ER115NPT T-C16EL115NPT T-C16IR115NPT T-C16IL115NPT $ / T-C16ER8NPT T-C16EL8NPT T-C16IR8NPT T-C16IL8NPT $12.95 NPTF DRYSEAL INSERTS ANSI INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD INSERT SERIES I.C. PITCH TPI X Y Right Hand EXTERNAL Left Hand Right Hand Master Catalog INTERNAL Left Hand 6 5/ T-C06IR27NPF T-C06IL27NPF $ / T-C08IR27NPF T-C08IL27NPF $ / T-C08IR18NPF T-C08IL18NPF $ / T-C11ER27NPF T-C11EL27NPF T-C11IR27NPF T-C11IL27NPF $ / T-C11ER18NPF T-C11EL18NPF T-C11IR18NPF T-C11IL18NPF $ / T-C11ER14NPF T-C11EL14NPF T-C11IR14NPF T-C11IL14NPF $ / T-C16ER27NPF T-C16EL27NPF T-C16IR27NPF T-C16IL27NPF $ / T-C16ER18NPF T-C16EL18NPF T-C16IR18NPF T-C16IL18NPF $ / T-C16ER14NPF T-C16EL14NPF T-C16IR14NPF T-C16IL14NPF $ / T-C16ER11.5NPF T-C16EL11.5NPF T-C16IR11.5NPF T-C16IL11.5NPF $ / T-C16ER8NPF T-C16EL8NPF T-C16IR8NPF T-C16IL8NPF $12.95 GRADE INFORMATION How To Order: 1) Pick the required insert from table above eg: T-C11ERA60 2) Pick a Carbide grade from the Grades table below - eg. 4 for superalloys and stainless steels 3) Order T-C11ERA604 4) Pick toolholder (ext) or boring bar (int) from pages Carmex Grade USST Grade CARMEX GRADE INFORMATION Carbide ANSI Coating Materials P25C P5 C5 TIN Hard Steels MXC M2 C2-C3 TIN Soft Steels, Stainless Steels, Cast Iron MA 4 C3-C4 TIALN Superalloys, Stainless Steels K20 K2 C2 UNCOATED Aluminum, Non Ferrous

101 LAYDOWN THREAD TURNING INSERTS ACME 29 THREAD INSERTS C INSERT SERIES I.C. PITCH TPI X Y Right Hand EXTERNAL Left Hand Right Hand INTERNAL Left Hand 8 3/ T-C08IR16ACM T-C08IL16ACM $ /16U T-C08UIRL14ACM T-C08UIRL14ACM $ U 3/16U T-C08UIRL12ACM T-C08UIRL12ACM $ /16U T-C08UIRL10ACM T-C08UIRL10ACM $ / T-C11ER16ACM T-C11EL16ACM - - $ / T-C16ER16ACM T-C16EL16ACM - - $ / T-C16ER14ACM T-C16EL14ACM T-C16IR14ACM T-C16IL14ACM $ / T-C16ER12ACM T-C16EL12ACM T-C16IR12ACM T-C16IL12ACM $ / T-C16ER10ACM T-C16EL10ACM T-C16IR10ACM T-C16IL10ACM $ / T-C16ER8ACM T-C16EL8ACM T-C16IR8ACM T-C16IL8ACM $ / T-C22ER6ACM T-C22EL6ACM T-C22IR6ACM T-C22IL6ACM $ / T-C22ER5ACM T-C22EL5ACM T-C22IR5ACM T-C22IL5ACM $ U 1/2U T-C22UERL4ACM T-C22UERL4ACM T-C22UIRL4ACM T-C22UIRL4ACM $ / T-C27ER4ACM T-C27EL4ACM T-C27IR4ACM T-C27IL4ACM $ U 5/8U T-C27UERL3ACM T-C27UERL3ACM T-C27UIRL3ACM T-C27UIRL3ACM $ U 3/4U T-C33UERL2ACM T-C33UERL2ACM T-C33UIRL2ACM T-C33UIRL2ACM $ STU ACME 29 THREAD INSERTS INSERT SERIES I.C. PITCH TPI X Y Right Hand EXTERNAL Left Hand Right Hand INTERNAL Left Hand 8 3/ T-C08IR16SAC T-C08IL16SAC $ /16U T-C08UIR/L14SAC T-C08UIR/L14SAC $ U 3/16U T-C08UIR/L12SAC T-C08UIR/L12SAC $ /16U T-C08UIR/L10SAC T-C08UIR/L10SAC $ / T-C11ER16SAC T-C11EL16SAC - - $ / T-C16ER16SAC T-C16EL16SAC - - $ / T-C16ER14SAC T-C16EL14SAC T-C16IR14SAC T-C16IL14SAC $ / T-C16ER12SAC T-C16EL12SAC T-C16IR12SAC T-C16IL12SAC $ / T-C16ER10SAC T-C16EL10SAC T-C16IR10SAC T-C16IL10SAC $ / T-C16ER8SAC T-C16EL8SAC T-C16IR8SAC T-C16IL8SAC $ / T-C16ER6SAC T-C16EL6SAC T-C16IR6SAC T-C16IL6SAC $ / T-C22ER5SAC T-C22EL5SAC T-C22IR5SAC T-C22IL5SAC $ U 1/2U T-C22UER/L4SAC T-C22UER/L4SAC T-C22UIR/L4SAC T-C22UIR/L4SAC $ /2U T-C22UER/L3SAC T-C22UER/L3SAC T-C22UIR/L3SAC T-C22UIR/L3SAC $ / T-C27ER4SAC T-C27EL4SAC T-C27IR4SAC T-C27IL4SAC $ / T-C27ER3SAC T-C27EL3SAC T-C27IR3SAC T-C27IL3SAC $ U 3/4U T-C33UER/L2SAC T-C33UER/L2SAC T-C33UIR/L2SAC T-C33UIR/L2SAC $ AMERICAN UTTRESS THREAD INSERTS Full Line Available! Please call for more information. CARIDE INSERTS INSERT SERIES I.C. PITCH TPI X Y Right Hand EXTERNAL Left Hand Right Hand INTERNAL Left Hand 11 1/ T-C11ER20AUT T-C11EL20AUT T-C11IR20AUT T-C11IL20AUT $ / T-C11ER16AUT T-C11EL16AUT T-C11IR16AUT T-C11IL16AUT $ / T-C16ER20AUT T-C16EL20AUT T-C16IR20AUT T-C16IL20AUT $ / T-C16ER16AUT T-C16EL16AUT T-C16IR16AUT T-C16IL16AUT $ / T-C16ER12AUT T-C16EL12AUT T-C16IR12AUT T-C16IL12AUT $ / T-C16ER10AUT T-C16EL10AUT T-C16IR10AUT T-C16IL10AUT $ / T-C22ER8AUT T-C22EL8AUT T-C22IR8AUT T-C22IL8AUT $ / T-C22ER6AUT T-C22EL6AUT T-C22IR6AUT T-C22IL6AUT $ U 1/2U T-C22UER4AUT T-C22UEL4AUT T-C22UIR4AUT T-C22UIL4AUT $ U 5/8U T-C27UER3AUT T-C27UEL3AUT T-C27UIR3AUT T-C27UIL3AUT $ Master Catalog 369 DEURRING

102 CHUCK JAWS LATHE WORKHOLDING LAYDOWN THREAD TURNING INSERTS & HOLDERS OIL THREAD INSERTS C MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INSERT I.C. SERIES API ROUND API Round PITCH TPI X Y CONNECTION No.or Size TAPER IPF Right Hand EXTERNAL Left Hand Right Hand Oil V40 INTERNAL Left Hand 3/ T-C16ER10APR T-C16EL10APR T-C16IR10APR T-C16IL10APR $ / T-C16ER8APR T-C16EL8APR T-C16IR8APR T-C16IL8APR $15.24 APIV / /8-41/2 REG 3 T-C22ER5AP403 T-C22EL5AP403 T-C22IR5AP403 T-C22IL5AP403 $19.05 APIV-0.038R 5/ NC23-NC50 2 T-C27ER4AP382 T-C27EL4AP382 T-C27IR4AP382 T-C27IL4AP382 $ / NC56-NC77 3 T-C27ER4AP383 T-C27EL4AP383 T-C27IR4AP383 T-C27IL4AP383 $25.14 APIV-0.050R 5/ /8 REG 2 T-C27ER4AP502 T-C27EL4AP502 T-C27IR4AP502 T-C27IL4AP502 $ / /2, 75/8, 85/8 REG 3 T-C27ER4AP503 T-C27EL4AP503 T-C27IR4AP503 T-C27IL4AP503 $25.14 TOOLHOLDERS FOR EXTERNAL LAYDOWN THREAD TURNING INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Full Line Available! Please call for more information. HOLDER SERIES Master Catalog =H in C in F in Right Handed EXTERNAL Left Handed T-CMSER0375H11 T-CMSEL0375H11 $ T-CMSER0375D16 T-CMSEL0375D16 $ T-CMSER0500F16 T-CMSEL0500F16 $ T-CMSER0625H16 T-CMSEL0625H16 $ T-CMSER0750K16 T-CMSEL0750K16 $ T-CMSER1000M16 T-CMSEL1000M16 $ T-CMSER1250P16 T-CMSEL1250P16 $ T-CMSER1000M22 T-CMSEL1000M22 $ T-CMSER1250P22 T-CMSEL1250P22 $ T-CMSER1500R22 T-CMSEL1500R22 $ U T-CMSER1000M22U T-CMSEL1000M22U $ T-CMSER1250P22U T-CMSEL1250P22U $ T-CMSER1000M27 T-CMSEL1000M27 $ T-CMSER1250P27 T-CMSEL1250P27 $ T-CMSER1000M27U T-CMSEL1000M27U $ U T-CMSER1250P27U T-CMSEL1250P27U $ T-CMSER1500R27U T-CMSEL1500R27U $ U T-CMSER1250P33U T-CMSEL1250P33U $ Important Notes: Use External Right Handed Holders with External Right Handed Laydown Inserts of the same Insert Series only. Similarly for Left Handed Holders and Inserts. Do not interchange insert series or insert hands.

103 LAYDOWN INTERNAL THREADING ORING ARS ORING ARS FOR LAYDOWN INTERNAL THREADING HOLDER SERIES Min ore in. SHANK D in. D1 in. C () in. L1 in. F in. ANVIL USED COOLANT THROUGH Right Handed INTERNAL Left Handed Steel NO NO T-CMSIR0205H06 T-CMSIL0205H06 $ Steel NO NO T-CMSIR0265K08 T-CMSIL0265K08 $ U Steel NO NO T-CMSIR0310K08U T-CMSIL0310K08U $ Steel NO NO T-CMSIR0375H11 T-CMSIL0375H11 $ Steel NO NO T-CMSIR0375K11 T-CMSIL0375K11 $ Steel YES YES T-CMSIR0375K11 T-CMSIL0375K11 $ Steel NO NO T-CMSIR0500L11 T-CMSIL0500L11 $ Carbide NO YES T-CMSIR0500P11C T-CMSIL0500P11C $ Steel NO NO T-CMSIR0500M16 T-CMSIL0500M16 $ Steel YES YES T-CMSIR0500M16 T-CMSIL0500M16 $ Steel NO NO T-CMSIR0625P16 T-CMSIL0625P16 $ Steel YES YES T-CMSIR0625P16 T-CMSIL0625P16 $ Steel YES NO T-CMSIR0750P16 T-CMSIL0750P16 $ Steel YES YES T-CMSIR0750P16 T-CMSIL0750P16 $ Steel YES NO T-CMSIR1000R16 T-CMSIL1000R16 $ Steel YES YES T-CMSIR1000R16 T-CMSIL1000R16 $ Steel YES NO T-CMSIR1250S16 T-CMSIL1250S16 $ Steel YES NO T-CMSIR1500T16 T-CMSIL1500T16 $ Steel NO NO T-CMSIR0750P22 T-CMSIL0750P22 $ Steel YES NO T-CMSIR1000R22 T-CMSIL1000R22 $ Steel YES NO T-CMSIR1250S22 T-CMSIL1250S22 $ Steel YES NO T-CMSIR1500T22 T-CMSIL1500T22 $ u Steel YES NO T-CMSIR1250S22U T-CMSIL1250S22U $ Steel YES NO T-CMSIR1500T22U T-CMSIL1500T22U $ Steel YES NO T-CMSIR1250S27 T-CMSIL1250S27 $ Steel YES NO T-CMSIR1500T27 T-CMSIL1500T27 $ Steel YES NO T-CMSIR2000U27 T-CMSIL2000U27 $ Steel YES NO T-CMSIR1250S27U T-CMSIL1250S27U $ u Steel YES NO T-CMSIR1500T27U T-CMSIL1500T27U $ Steel YES NO T-CMSIR2000U27U T-CMSIL2000U27U $ Steel YES NO T-CMSIR2500V27U T-CMSIL2500V27U $ u Steel YES NO T-CMSIR2000U33U T-CMSIL2000U33U $ Important Notes: Use Internal Right Handed Holders With Internal Right Handed Laydown Inserts Of The Same Insert Series Only. Similarly For Left Handed Holders And Inserts. Do Not Interchange Insert Series Or Insert Hands. CARIDE INSERTS CARMEX GRADE INFORMATION Carmex Grade How To Order CARMEX Inserts: 1) Pick the required insert from table ex: T-C11ERA60 2) Pick a Carbide grade from the Grades table below - eg. 4 for superalloys and stainless steels 3) Order T-C11ERA604 4) Pick toolholder (ext) or boring bar (int) from pages USST Grade Suffix CARMEX GRADE INFORMATION Carbide ANSI Coating Materials P25C P5 C5 TIN Hard Steels MXC M2 C2-C3 TIN Soft Steels, Stainless Steels, Cast Iron MA 4 C3-C4 TIALN Superalloys, Stainless Steels K20 K2 C2 UNCOATED Aluminum, Non Ferrous Master Catalog 371 DEURRING

104 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS THREADMILLS SOLID CARIDE THREADMILLS UN-AMERICAN UNIFIED 60 Full Line Available! Please call for more information. TPI UNC UNF UNEF d D NO COOLANT PASSAGE SOLID CARIDE THREADMILLS NPT Free Programming Help! Please Call For More Information. No. of flutes l L / T-CT40UN-200 $ / T-CT32UN-205 $ / T-CT28UN-210 $ /16-1/2 1/ T-CT28UN-215 $ /16-3/8 1/ T-CT24UN-220 $ /16-5/8 5/ T-CT24UN-225 $ /4 1/ T-CT20UN-230 $ /16-1/2 5/ T-CT20UN-235 $ /4-1 1/ T-CT20UN-240 $ /16 1/ T-CT18UN-245 $ /16-5/8 11/8-15/8 3/ T-CT18UN-250 $ /8 1/ T-CT16UN-255 $ /4 1/ T-CT16UN-260 $ /16 5/ T-CT14UN-265 $ /8 5/ T-CT14UN-270 $ /2 5/ T-CT13UN-275 $ /16 3/ T-CT12UN-280 $ /2 5/ T-CT12UN-285 $ /8 3/ T-CT11UN-290 $ /4 1/ T-CT10UN-295 $ /8 5/ T-CT9UN-300 $ / T-CT8UN-305 $ /8-11/4 3/ T-CT7UN-310 $ WITH THRU COOLANT HOLE / T-CT32UN-315C $ /4 1/ T-CT28UN-320C $ /16-1/2 1/ T-CT28UN-325C $ /16 5/ T-CT24UN-330C $ /8-5/8 5/ T-CT24UN-335C $ /4 1/ T-CT20UN-340C $ /16 5/ T-CT20UN-345C $ /2 3/ T-CT20UN-350C $ /4-1 1/ T-CT20UN-355C $ /16 1/ T-CT18UN-360C $ /16-5/8 11/8-15/8 1/ T-CT18UN-365C $ /8 5/ T-CT16UN-370C $ /4 1/ T-CT16UN-375C $ /16 5/ T-CT14UN-380C $ /8 5/ T-CT14UN-385C $ /2 3/ T-CT13UN-390C $ /16 1/ T-CT12UN-395C $ /2 5/ T-CT12UN-400C $ /8 1/ T-CT11UN-405C $ /4 5/ T-CT10UN-410C $ /8 5/ T-CT9UN-415C $ Full Line Available! Please call for more information. ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD TPI Standard d D NO COOLANT PASSAGE No. Of Flutes Master Catalog l L 27 1/8 1/ T-CT27NPT-100 $ /4-3/8 5/ T-CT18NPT-105 $ /2-3/4 1/ T-CT14NPT-110 $ / T-CT115NPT-115 $ >21/2 3/ T-CT8NPT-120 $ With Thru Coolant Hole 27 1/8 5/ T-CT27NPT-125C $ /4-3/8 3/ T-CT18NPT-130C $ /2-3/4 5/ T-CT14NPT-135C $ / T-CT115NPT-140C $405.90

105 THREADMILLS SOLID CARIDE THREADMILLS DRYSEAL SOLID CARIDE THREADMILLS ISO METRIC 360 Full Line Available! Please call for more information. TPI Standard d D No. Of Flutes l Master Catalog 373 L No Coolant Passage 27 1/8 1/ T-CT27NPTF-145 $ /4-3/8 5/ T-CT18NPTF-150 $ /2-3/4 1/ T-CT14NPTF-155 $ / T-CT115NPTF-160 $ >21/2 3/ T-CT8NPTF-165 $ With Thru Coolant Hole 27 1/8 5/ T-CT27NPTF-170C $ /4-3/8 3/ T-CT18NPTF-175C $ /2-3/4 5/ T-CT14NPTF-180C $ / T-CT115NPF-185C $ Pitch mm Metric Coarse Free Programming Help! Please Call For More Information. Metric Fine d D No. of flutes l L No Coolant Passage 0.5 M3 ø>=.16 1/ T-CT0.5M-500 $ ø>=.20 1/ T-CT0.5M-505 $ M4 ø>=.20 1/ T-CT0.7M-510 $ ø>=.24 1/ T-CT0.75M-515 $ M5 ø>=.24 1/ T-CT0.8M-520 $ M6 ø>=.28 1/ T-CT1.0M-525 $ M6 ø>=.28 1/ T-CT1.0M-530 $ ø>=.35 1/ T-CT1.0M-535 $ ø>=.39 5/ T-CT1.0M-540 $ M8 ø>=.39 1/ T-CT1.25M-545 $ M8 ø>=.39 1/ T-CT1.25M-550 $ M10 ø>=.47 5/ T-CT1.5M-555 $ M10 ø>=.47 5/ T-CT1.5M-560 $ ø>=.55 3/ T-CT1.5M-565 $ ø>=.79 5/ T-CT1.5M-570 $ M12 ø>=.55 5/ T-CT1.75M-575 $ M12 ø>=.55 5/ T-CT1.75M-580 $ M16 ø>=.67 3/ T-CT2.0M-585 $ M16 ø>=.67 3/ T-CT2.0M-590 $ ø>=.71 1/ T-CT2.0M-595 $ ø>=1.02 3/ T-CT2.0M-600 $ M20 ø>=.87 5/ T-CT2.5M-605 $ M20 ø>=.87 5/ T-CT2.5M-610 $ M24 ø>=.98 5/ T-CT3.0M-615 $ M24 ø>=.98 5/ T-CT3.0M-620 $ M28 ø>=1.10 3/ T-CT3.0M-625 $ With Thru Coolant Hole ø>=.20 1/ T-CT0.5M-630C $ M4 ø>=.20 1/ T-CT0.7M-635C $ ø>=.24 1/ T-CT0.75M-640C $ M5 ø>=.24 1/ T-CT0.8M-645C $ M6 ø>=.28 1/ T-CT1.0M-650C $ M6 ø>=.28 1/ T-CT1.0M-655C $ ø>=.35 1/ T-CT1.0M-660C $ ø>=.39 5/ T-CT1.0M-665C $ M8 ø>=.39 1/ T-CT1.25M-670C $ M8 ø>=.39 1/ T-CT1.25M-675C $ M10 ø>=.47 5/ T-CT1.5M-680C $ M10 ø>=.47 5/ T-CT1.5M-685C $ ø>=.55 3/ T-CT1.5M-690C $ ø>=.79 5/ T-CT1.5M-695C $ M12 ø>=.47 3/ T-CT1.75M-700C $ M12 ø>=.47 3/ T-CT1.75M-705C $ M14 ø>=.59 3/ T-CT2.0M-710C $ M16 ø>=.67 1/ T-CT2.0M-715C $ M16 ø>=.67 1/ T-CT2.0M-720C $ ø>=.94 3/ T-CT2.0M-725C $ CARIDE INSERTS DEURRING

106 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD THREADMILLS HELICAL FLUTE THREAD MILLS UN, NPT & NPTF THREADS SOLID CARIDE-AlTiN Coated FEATURES: Completely CNC ground Helical flute design for reduced cutting forces, smoother cuts, longest tool life and maximum thread milling performance 100% thread form for superior threads compared to tapping Cuts right and left hand threads Suitable for all types of materials, including heat treated and difficult to machine workpieces. Supplied with AlTiN coating. Uncoated thread mills also available, please call for more information Full Line Available! Please call for more information. meter Cutter meter Length of Cut Overall Length T.I.R. Maximum to ± to.000 ± SOLID CARIDE MINI THREADMILLS UN-UNIFIED AMERICAN 60 General Purpose For All Materials HELICAL FLUTE THREAD MILLS- NPT, NPTF THREADS Minimum Thread Master Catalog Pitch Cut. D1 D2 L1 LOC L2 No. Of Flutes 1/16 & 1/8 NPT /4 2-1/ MI-TM27NPTX $ /4 & 3/8 NPT /16 2-1/ MI-TM18NPTX $ /2 & 3/4 NPT / MI-TM14NPTX $ " & 2" NPT / MI-TM11NPTX $ /16 & 1/8 NPTF /4 2-1/ MI-TM27NPTFX $ /4 & 3/8 NPTF /16 2-1/ MI-TM18NPTFX $ /2 & 3/4 NPTF / MI-TM14NPTFX $ " & 2" NPTF / MI-TM11NPTFX $ HELICAL FLUTE THREAD MILLS- UN THREADS Minimum Thread & Pitch Cut. D1 D2 L1 LOC L2 No. Of Flutes /4 2 3/16 2 MI-TM11240X $ /4 2 1/4 2 MI-TM13832X $ /4 2 1/4 3 MI-TM16432X $ /4 2 5/16 3 MI-TM19024X $ /4 2 5/16 3 MI-TM19028X $ /4 2 5/16 3 MI-TM19032X $ / /4 2-1/2 1/2 3 MI-TM25020X $ / /4 2-1/2 1/2 3 MI-TM25028X $ / /4 2-1/2 5/8 3 MI-TM31218X $ / /4 2-1/2 5/8 3 MI-TM31224X $ / /16 2-1/2 3/4 4 MI-TM37516X $ / /16 2-1/2 3/4 4 MI-TM37524X $ / /16 2-1/2 3/4 4 MI-TM43714X $ / /8 3 7/8 4 MI-TM43720X $ / /8 3 7/8 4 MI-TM50013X $ / /8 3 7/8 4 MI-TM5622X $ / /8 3 7/8 4 MI-TM56218X $ / / /4 4 MI-TM62511X $ / / /4 4 MI-TM75010X $ / / /4 4 MI-TM75012X $ / / /4 4 MI-TM75016X $ / / /8 4 MI-TM87509X $ / / /4 4 MI-TM87514X $ " / /8 4 MI-TM00108X $ Free Programming Help! Please Call For More Information. TPI UNC UNF d D No of Flutes l L For Thread Depth Up To 2xD / T-CMTS72UN-800 $ / T-CMTS64UN-805 $ / T-CMTS56UN-810 $ / T-CMTS48UN-815 $ / T-CMTS40UN-820 $ / T-CMTS40UN-825 $ / T-CMTS36UN-830 $ / T-CMTS32UN-835 $ / T-CMTS32UN-840 $ /4 1/ T-CMTS28UN-845 $ , 12-1/ T-CMTS24UN-850 $ /16 5/ T-CMTS24UN-855 $ /4-1/ T-CMTS20UN-860 $ For Thread Depth Up To 3xD / T-CMTS40UN-865 $ / T-CMTS32UN-870 $ /4 1/ T-CMTS28UN-875 $ /16 5/ T-CMTS24UN-880 $ /4-1/ T-CMTS20UN-885 $138.60

107 THREADMILLS INSERTS THREAD MILL INSERTS FOR THREADING ON CNC MILLING MACHINES USING HELICAL INTERPOLATION PROGRAMS Free Programming Help! Please Call For More Information. GRADE MT7 - Sub micron TiAlN multi layer coated grade general purpose for all materials Please See Following Page For Holders FOR ISO METRIC THREADS INTERNAL EXTERNAL INSERT SIZE "A" Pitch mm 0.50 T-CT12 I 0.5M $ T-CT12 I 0.75M $ T-CT12 I 1.0M $ T-CT12 I 1.25M $ T-CT12 I 1.5M $ T-CT14 I 0.5M $ T-CT14 I 0.75M $31.35 T-CT14 E 0.75M $ T-CT14 I 1.0M $31.35 T-CT14 E 1.0M $ T-CT14 I 1.25M $31.35 T-CT14 E 1.25M $ T-CT14 I 1.5M $31.35 T-CT14 E 1.5M $ T-CT14 I 1.75M $31.35 T-CT14 E 1.75M $ T-CT14 I 2.0M $31.35 T-CT14 E 2.0M $ T-CT14 I 2.5M $31.35 T-CT14 E 2.5M $ T-CT21 I 1.0M $47.03 T-CT21 E 1.0M $ T-CT21 I 1.5M $47.03 T-CT21 E 1.5M $ T-CT21 I 1.75M $ T-CT21 I 2.0M $47.03 T-CT21 E 2.0M $ T-CT21 I 2.5M $47.03 T-CT21 E 2.5M $ T-CT21 I 3.0M $47.03 T-CT21 E 3.0M $ T-CT21 I 3.5M $ T-CT30 I 1.5M $67.93 T-CT30 E 1.5M $ T-CT30 I 2.0M $67.93 T-CT30 E 2.0M $ T-CT30 I 3.0M $67.93 T-CT30 E 3.0M $ T-CT30 I 3.5M $67.93 T-CT30 E 3.5M $ T-CT30 I 4.0M $67.93 T-CT30 E 4.0M $ T-CT30 I 4.5M $67.93 T-CT30 E 4.5M $ T-CT40 I 1.5M $ T-CT40 E 1.5M $ T-CT40 I 2.0M $ T-CT40 E 2.0M $ T-CT40 I 3.0M $ T-CT40 E 3.0M $ T-CT40 I 3.5M $ T-CT40 I 4.0M $ T-CT40 E 4.0M $ T-CT40 I 4.5M $ T-CT40 I 5.0M $ T-CT40 E 5.0M $ T-CT40 I 5.5M $ T-CT40 I 6.0M $ T-CT40 E 6.0M $ ADVANTAGES OF MILL THREAD TOOLS Same toolholder and insert can produce right and left-hand threads A single insert & toolholder can produce a given thread on many diameters (external & internal) Most inserts are double sided, having two cutting edges. Thread is produced in one tool pass. Mill Thread tools are capable of producing taper threads. Improved productivity thanks to increased cutting speeds and multitooth type carbide inserts Threading to one pitch of a shoulder in a blind hole. Longer tool life thanks to special multilayer coating process Lower tooling costs, considerably less expensive than using taps and dies Since lower machine power required, smaller machine can produce larger threads in single operation with less idle time and tool changes. Inserts are compatible with Kennametal, Stellram, Xactform & Iscar Holders! FOR UN AMERICAN UNIFIED THREADS INTERNAL EXTERNAL INSERT TPI SIZE "A" 32 T-CT12 I 32UN $ T-CT12 I 28UN $ T-CT12 I 24UN $ T-CT12 I 20UN $ T-CT12 I 18UN $ T-CT12 I 16UN $ T-CT14 I 32UN $31.35 T-CT14 E 32UN $ T-CT14 I 28UN $31.35 T-CT14 E 28UN $ T-CT14 I 27UN $ T-CT14 I 24UN $31.35 T-CT14 E 24UN $ T-CT14 I 20UN $31.35 T-CT14 E 20UN $ T-CT14 I 18UN $31.35 T-CT14 E 18UN $ T-CT14 I 16UN $31.35 T-CT14 E 16UN $ T-CT14 I 14UN $31.35 T-CT14 E 14UN $ T-CT14 I 12UN $31.35 T-CT14 E 12UN $ T-CT21 I 24UN $47.03 T-CT21 E 24UN $ T-CT21 I 20UN $47.03 T-CT21 E 20UN $ T-CT21 I 18UN $47.03 T-CT21 E 18UN $ T-CT21 I 16UN $47.03 T-CT21 E 16UN $ T-CT21 I 14UN $47.03 T-CT21 E 14UN $ T-CT21 I 12UN $47.03 T-CT21 E 12UN $ T-CT21 I 10UN $47.03 T-CT21 E 10UN $ T-CT21 I 8UN $ T-CT30 I 20UN $67.93 T-CT30 E 20UN $ T-CT30 I 18UN $67.93 T-CT30 E 18UN $ T-CT30 I 16UN $67.93 T-CT30 E 16UN $ T-CT30 I 14UN $67.93 T-CT30 E 14UN $ T-CT30 I 12UN $67.93 T-CT30 E 12UN $ T-CT30 I 10UN $67.93 T-CT30 E 10UN $ T-CT30 I 8UN $67.93 T-CT30 E 8UN $ T-CT30 I 6UN $67.93 T-CT30 E 6UN $ T-CT40 I 16UN $ T-CT40 E 20UN $ T-CT40 I 14UN $ T-CT40 E 18UN $ T-CT40 I 12UN $ T-CT40 E 16UN $ T-CT40 I 10UN $ T-CT40 E 14UN $ T-CT40 I 8UN $ T-CT40 E 12UN $ T-CT40 I 6UN $ T-CT40 E 10UN $ T-CT40 I 4.5UN $ T-CT40 E 8UN $ T-CT40 I 4UN $ T-CT40 E 6UN $ Master Catalog 375 CARIDE INSERTS DEURRING

108 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS THREADMILLS INSERTS/HOLDERS THREAD MILL INSERTS (continued) FOR THREADING ON CNC MILLING MACHINES Using Helical Interpolation Programs For NPT Threads INSERT SIZE "A TPI INTERNAL/EXTERNAL For NPTF DRYSEAL Threads INSERT SIZE "A TPI INTERNAL/EXTERNAL T-CT12 IE 18NPT $ T-CT12 IE 18NPF $ T-CT14 IE 18NPT $ T-CT14 IE 18NPF $ T-CT14 IE 14NPT $ T-CT14 IE 14NPF $ T-CT21 IE 14NPT $ T-CT21 IE 14NPF $ T-CT21 IE 11.5NP $ T-CT21 IE 11.5NP $ T-CT30 IE 11.5NP $ T-CT30 IE 8NPF $ T-CT30 IE 8NPT $ T-CT40 IE 8NPF $ T-CT40 IE 11.5NP $ T-CT40 IE 8NPT $ THREAD MILL INSERTS HOLDERS FOR THREADING ON CNC MILLING MACHINES Using Helical Interpolation Programs Free Programming Help! Please Call For More Information. Full Line Available! Please call for more information. INDEXALE DRILLS TURNING & ORING TOOLHOLDERS ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Fig #1 Fig #2 Fig #3 Fig #4 Fig #5 Style Std Lngth Long Shnk Std Lngth Long Shnk Shell Mill Figure No For Insert Size "A" D D1 D2 L L1 No Of Inserts Coolant Thru Material Master Catalog Yes Steel T-CTSR0375H12 $ S12 K Yes Steel T-CTSR0390H12 $ S12 K Yes Steel T-CTSR0500F14 $ S14 K Yes Steel T-CTSR0540F14 $ S14 K Yes Steel T-CTSR0570H14 $ S14 K Yes Steel T-CTSR0670H14 $ S14 K Yes Steel T-CTSR0790H21 $ S21 K Yes Steel T-CTSR1140J30 $ S30 K Yes Steel T-CTSR1730M40 $ S40 K Yes Steel T-CTSR0940K21 $ S21 K Yes Steel T-CTSR1240M30 $ S30 K Yes Steel T-CTSR1500M30 $ S30 K Yes Steel T-CTSR0790H14-2 $ S14 K Yes Steel T-CTSR1180J21-2 $ S21 K Yes Steel T-CTSR1580L30-2 $ S30 K Yes Steel T-CTSR1970M40-2 $ S40 K Yes Carbide T-CTSR0390K12C $ S12 K Yes Carbide T-CTSR0500J14C $ S14 K Yes Carbide T-CTSR0620K14C $ S14 K Yes Carbide T-CTSR0820M21C $ S21 K No n/a T-CTSR2480C21-5 $ S21 K No n/a T-CTSR2480C30-4 $ S30 K No n/a T-CTSR3150D30-4 $ S30 K30 n/a n/a No n/a T-CTSR3940D30-4 $ S30 K No n/a T-CTSR3150D40-4 $ S40 K No n/a T-CTSR3940E40-4 $ S40 K40 Insert Torx

109 ON EDGE GROOVING/ THREADING INSERTS ON EDGE GROOVING INSERTS STANDARD HOLE DOULE COUNTERSUNK HOLE I.C. T D W Industry Coated Coated Industry Coated Coated (for reference only) GP3 Grade GP-50 Grade (for reference only) GP3 Grade GP-50 Grade TNMA-32-NGL GV-751 TNMA-32-NGR GV-702 TNMC-32-NGR-.062 GV-652-3/8 1/8 TNMA-32-NGL $ $14.84 TNMC-32-NGL.094 GV-653 $14.84 GV-753 $ TNMA-32-NGR-.094 GV-604 GV-704 TNMC-32-NGR-.094 GV-654 GV TNMA-32-NGC.125 GV-605 GV-705 TNMC-32-NGC.125 GV-655 GV TNMA-43-NGL.062 GV-606 GV-706 TNMC-43-NGL.062 GV-656 GV-756 TNMA-43-NGR-.062 GV-607 GV-707 TNMC-43-NGR-.062 GV-657 GV TNMA-43-NGL.094 GV-608 GV-708 TNMC-43-NGL.094 GV-658 GV-758 TNMA-43-NGR-.094 GV-609 GV-709 TNMC-43-NGR-.094 GV-659 GV-759 1/2 3/16 TNMA-43-NGL.125 GV-610 GV-710 TNMC-43-NGL.125 GV-660 GV-760 $17.51 $17.51 $ TNMA-43-NGR-.125 GV-611 GV-711 TNMC-43-NGR-.125 GV-661 GV-761 $17.51 TNMA-43-NGC-.125 GV-612 GV-712 TNMC-43-NGC TNMA-43-NGL TNMC-43-NGL-.156 GV-663 GV TNMA-43-NGR TNMC-43-NGR-.156 GV-664 GV TNMA-43-NGC-.188 GV-615 GV-715 TNMC-43-NGC-.188 GV-665 GV V ON EDGE THREADING INSERTS T I.C. Hole Style S= Straight hole DCS=Double Countersunk TPI IC T R W D Hole Style I. T Rake Industry Coated GP-3 Coated GP-50 (C5) / /.005 S NEG TNMA-32NV VT-601 $14.95 VT-701 $ / /.005 S NEG TNMA-43NV VT-602 $16.24 VT-702 $ / /.010 S NEG TNMA-54NV VT-603 $22.91 VT-703 $ / /.005 S POS TPMA-32NV VT-604 $14.95 VT-704 $ / /.005 S POS TPMA-43NV VT-605 $16.24 VT-705 $ / /.010 S POS TPMA-54NV VT-606 $22.91 VT-706 $ / /.005 DCS NEG TNMC-32NV VT-607 $14.95 VT-707 $ / /.005 DCS NEG TNMC-43NV VT-608 $16.24 VT-708 $ / /.010 DCS NEG TNMC-54NV VT-609 $22.91 VT-709 $ / /.005 DCS POS TPMC-32NV VT-610 $14.95 VT-710 $ / /.005 DCS POS TPMC-43NV VT-611 $16.24 VT-711 $ / /.010 DCS POS TPMC-54NV VT-612 $22.91 VT-712 $22.91 Full Line Available! Please call for more information. CARIDE INSERTS HOLDERS FOR EXTERNAL GROOVING & THREADING From either of the two insert tables above match the IC of the insert to the holders in the table below to get matched Inserts and Holders for your needs. ARS FOR INTERNAL GROOVING & THREADING From either of the two insert tables above match the IC of the insert to the holders in the table below to get matched Inserts and Holders for your needs. Left/ Right Insert IC A C D E F Holder R 3/8 3/4 3/4 4-1/ T-MTVOR123 $75.95 L 3/8 3/4 3/4 4-1/ T-MTVOL123 $75.95 R 3/ T-MTVOR163 $79.04 L 3/ T-MTVOL163 $79.04 R 1/2 3/4 3/4 4-1/ T-MTVOR124 $75.95 L 1/2 3/4 3/4 4-1/ T-MTVOL124 $75.95 R 1/ T-MTVOR164 $79.04 L 1/ T-MTVOL164 $79.04 R 1/2 1-1/4 1-1/ T-MTVOR204 $93.12 R 5/ T-MTVOR165 $79.04 L 5/ T-MTVOL165 $79.04 R 5/8 1-1/4 1-1/ T-MTVOR205 $93.12 Left/ Right R Insert IC Min ore D L F V ar T-SIMTHOR163 $ /8 L T-SIMTHOL163 $ R T-SIMTHOR204 $ /2 L T-SIMTHOL204 $ R T-SIMTHOR244 $ /2 L T-SIMTHOL244 $ R T-SIMTHOR245 $ L 5/ T-SIMTHOL245 $ R T-SIMTHOR325 $ Master Catalog 377 DEURRING

110 CHUCK JAWS LATHE WORKHOLDING ENDMILLS MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING A Large Variety Of Endmills For All Of Your Cutting Needs! We offer endmills designed for maximum performance in all types of materials. Endmill designs for general purpose machining are available in a wide range of materials and flute variety. 2 FLUTE SQUARE END 3 FLUTE SQUARE END 4 FLUTE SQUARE END For Aluminum, Non-ferrous & Plastic For Finishing Non-ferrous & Hard Alloys For Steels & Stainless Steels Pages Pages Pages 379, & 6 FLUTE SQUARE END 3 FLUTE ROUGHING ENDMILLS 4 FLUTE ROUGHING For Steels & Stainless Steels Fine Pitch & Special Geometry Coarse & Fine Pitch For Steels Page 390 Pages Pages & 6 FLUTE ROUGHING 2 FLUTE ALL END 3 FLUTE ALL END Coarse & Fine Pitch For Steels For Aluminum, Plastic & Non-ferrous For Finishing Non-ferrous & Hard Alloys Page 399 Pages Page 402 ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD 4 FLUTE ALL END DRILL POINT/DRILL MILLS CORNER ROUNDING For Steels & Stainless Steels 60, 82, 90, 100, & 120 HSS, Cobalt & Carbide Pages 400, Pages 405 Page & 4 FLUTE CORNER RADIUS SQUARE/ALL END ROUGHER/FINSHERS MINIATURE/MICRO ENDMILLS Solid Carbide-MONSTER With Chipbreaker, Solid Carbide-MONSTER Square/all End, Solid Carbide Page 393 Page 394 Page VARIALE HELIX AlTiN COATED ROUGHING ENDMILLS 3 & 4 FLUTE ROUTERS FOR ALUMINUM Solid Carbide-Micro 100 Solid Carbide-Micro 100 Solid Carbide-Micro 100 Page 392 Page 399 Page Master Catalog

111 SOLID CARIDE ENDMILLS SOLID CARIDE ENDMILLS 2 FLUTE, SQUARE END Premium sub-micron C-2 carbide with 10% cobalt 30 helix, right hand spiral, right hand cut Available uncoated, Tin coated and TiAlN coated Tolerances: Cutting : +.000/-.002 : / Applications: Slotting, pocketing and plunging Materials: Cast Iron, non-ferrous metals, plastics and abrasive materials. SOLID CARIDE ENDMILLS 4 FLUTE, SQUARE END Premium sub-micron C-2 carbide with 10% cobalt 30 helix, right hand spiral, right hand cut Center cutting Increased core strength Available uncoated, Tin coated and TiAlN coated Tolerances: Cutting : +.000/-.002 : / Materials: Ferrous materials including stainless steel and high temperature alloys LOC. Uncoated TiN Coated TiAlN Coated 1/64 3/64 1/8 1-1/2 MO-EM $ /32 1/8 1/8 1-1/2 MO-EM $7.41 MO-EM $8.49 MO-EM $9.44 3/64 1/8 1/8 1-1/2 MO-EM $7.41 MO-EM $8.49 MO-EM $9.44 1/16 1/4 1/8 1-1/2 MO-EM $6.31 MO-EM $7.39 MO-EM $8.34 5/64 1/4 1/8 1-1/2 MO-EM $6.31 MO-EM $7.39 MO-EM $8.34 3/32 3/8 1/8 1-1/2 MO-EM $6.31 MO-EM $7.39 MO-EM $8.34 7/64 3/8 1/8 1-1/2 MO-EM $6.31 MO-EM $7.39 MO-EM $8.34 1/8 1/2 1/8 1-1/2 MO-EM $5.87 MO-EM $6.95 MO-EM $7.91 9/64 9/16 3/16 2 MO-EM $9.14 MO-EM $10.70 MO-EM $ /32 9/16 3/16 2 MO-EM $9.14 MO-EM $10.70 MO-EM $ /64 9/16 3/16 2 MO-EM $9.14 MO-EM $10.70 MO-EM $ /16 5/8 3/16 2 MO-EM $8.64 MO-EM $10.20 MO-EM $ /64 5/8 1/4 2-1/2 MO-EM $13.03 MO-EM $15.77 MO-EM $ /32 5/8 1/4 2-1/2 MO-EM $13.03 MO-EM $15.77 MO-EM $ /4 3/4 1/4 2-1/2 MO-EM $11.61 MO-EM $15.00 MO-EM $ /32 3/4 5/16 2-1/2 MO-EM $17.89 MO-EM $21.33 MO-EM $ /16 13/16 5/16 2-1/2 MO-EM $16.14 MO-EM $19.58 MO-EM $ /32 1 3/8 2-1/2 MO-EM $21.11 MO-EM $24.55 MO-EM $ /8 1 3/8 2-1/2 MO-EM $19.70 MO-EM $23.13 MO-EM $ /32 1 7/16 2-3/4 MO-EM $30.42 MO-EM $35.96 MO-EM $ /16 1 7/16 2-3/4 MO-EM $27.51 MO-EM $33.05 MO-EM $ /32 1 1/2 3 MO-EM $36.51 MO-EM $42.05 MO-EM $ /2 1 1/2 3 MO-EM $33.62 MO-EM $39.16 MO-EM $ /16 1-1/4 9/16 3-1/2 MO-EM $51.50 MO-EM $60.12 MO-EM $ /8 1-1/4 5/8 3-1/2 MO-EM $62.52 MO-EM $71.14 MO-EM $ /16 1-1/2 3/4 4 MO-EM $99.97 MO-EM $ MO-EM $ /4 1-1/2 3/4 4 MO-EM $95.81 MO-EM $ MO-EM $ /8 1-1/2 7/8 4 MO-EM $ MO-EM $ MO-EM $ /2 1 4 MO-EM $ MO-EM $ MO-EM $ LOC. American Made Carbide End Mills At High Speed Steel s! American Made Carbide End Mills At High Speed Steel s! Uncoated TiN Coated TiAlN Coated 1/64 3/64 1/8 1-1/2 MO-EM $ /32 1/8 1/8 1-1/2 MO-EM $7.41 MO-EM $8.49 MO-EM $9.44 3/64 1/8 1/8 1-1/2 MO-EM $7.41 MO-EM $8.49 MO-EM $9.44 1/16 1/4 1/8 1-1/2 MO-EM $6.31 MO-EM $7.39 MO-EM $8.34 5/64 1/4 1/8 1-1/2 MO-EM $6.31 MO-EM $7.39 MO-EM $8.34 3/32 3/8 1/8 1-1/2 MO-EM $6.31 MO-EM $7.39 MO-EM $8.34 7/64 3/8 1/8 1-1/2 MO-EM $6.31 MO-EM $7.39 MO-EM $8.34 1/8 1/2 1/8 1-1/2 MO-EM $5.87 MO-EM $6.95 MO-EM $7.91 9/64 9/16 3/16 2 MO-EM $9.14 MO-EM $10.70 MO-EM $ /32 9/16 3/16 2 MO-EM $9.14 MO-EM $10.70 MO-EM $ /16 5/8 3/16 2 MO-EM $8.64 MO-EM $10.20 MO-EM $ /32 5/8 1/4 2-1/2 MO-EM $13.03 MO-EM $15.77 MO-EM $ /4 3/4 1/4 2-1/2 MO-EM $11.61 MO-EM $14.34 MO-EM $ /32 3/4 5/16 2-1/2 MO-EM $17.89 MO-EM $21.33 MO-EM $ /16 13/16 5/16 2-1/2 MO-EM $16.14 MO-EM $19.58 MO-EM $ /32 1 3/8 2-1/2 MO-EM $21.11 MO-EM $24.55 MO-EM $ /8 1 3/8 2-1/2 MO-EM $19.70 MO-EM $23.13 MO-EM $ /32 1 7/16 2-3/4 MO-EM $30.42 MO-EM $35.96 MO-EM $ /16 1 7/16 2-3/4 MO-EM $27.51 MO-EM $33.05 MO-EM $ /32 1 1/2 3 MO-EM $36.51 MO-EM $42.05 MO-EM $ /2 1 1/2 3 MO-EM $33.62 MO-EM $39.16 MO-EM $ /16 1-1/4 9/16 3-1/2 MO-EM $51.50 MO-EM $60.12 MO-EM $ /8 1-1/4 5/8 3-1/2 MO-EM $62.52 MO-EM $71.14 MO-EM $ /16 1-1/2 3/4 4 MO-EM $99.97 MO-EM $ MO-EM $ /4 1-1/2 3/4 4 MO-EM $95.81 MO-EM $ MO-EM $ /8 1-1/2 7/8 4 MO-EM $ MO-EM $ MO-EM $ /2 1 4 MO-EM $ MO-EM $ MO-EM $ Master Catalog 379 C CARIDE INSERTS DEURRING

112 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-2 FLUTE/SQUARE END 2 FLUTE ENDMILLS SQUARE END HSS, Cobalt & Carbide For Aluminum, Non-Ferrous Materials & Plastic 2 Flute Square End Endmills (HSS, Cobalt & Carbide)- For Aluminum, Plastic & Non-Ferrous Materials Mill 1/32 3/64 1/16 5/64 3/32 Material LOC Cut Application Coating Type Flats Vendor Master Catalog CAR 3/32 1/8 1-1/2 NC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $8.48 C CO 3/32 3/16 2-1/4 CC Miniature -Precision Milling U DE - YG1 YG-EM50252 $10.20 C CAR 1/8 1/8 1-1/2 NC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $8.16 C CO 9/64 3/16 2-1/4 CC GP For Alum. & Non Ferrous U DE No MELIN ME /2 $15.20 CAR 1/8 1/8 1-1/2 CC Hi Perf For Alum. U DE - IMCO Micrograin IMCO $13.22 C CAR 3/16 1/8 1-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $8.16 C CO 3/16 3/16 1-1/2 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-602 $9.70 CO 3/16 3/16 2-1/4 CC GP For Alum. & Non Ferrous U DE No MELIN ME--602 $13.26 CO 7/32 3/16 2-1/2 CC GP For Alum. & Non Ferrous U DE No MELIN ME--602-L $17.96 CAR 3/16 1/8 1-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $8.48 C CO 15/64 3/16 1-1/2 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-602-1/2 $9.70 CO 15/64 3/16 2-1/4 CC GP For Alum. & Non Ferrous U DE No MELIN ME /2 $13.26 CAR 3/16 1/8 1-1/2 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM30556 $5.57 C CAR 3/16 1/8 1-1/2 XX GP For Alum. & Non Ferrous A DE - IMCO Spector IMCO $15.50 C CAR 3/8 1/8 1-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $8.16 C CO 9/32 3/16 1-1/2 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-603 $9.70 CO 9/32 3/16 2-1/4 CC GP For Alum. & Non Ferrous U DE No MELIN ME--603 $13.26 CO 9/32 3/16 2-1/4 CC Miniature -Precision Milling U DE - YG1 YG-EM50260 $9.25 C 7/64 CAR 3/8 1/8 1-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $8.48 C 1/8 9/64 5/32 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 1/4 1/8 1-1/2 CC GP For Alum. & Non Ferrous U SE No MELIN ME-AMGS-404 $7.19 CAR 3/8 1/8 2 CC GP For Alum. & Non Ferrous U DE Yes MELIN ME-MG-404 $11.42 CAR 1/2 1/8 1-1/2 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AMG-404 $7.53 CAR 1/2 1/8 1-1/2 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01558 $5.57 C CO 3/8 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $8.15 C CO 3/8 3/16 2-1/4 CC GP For Alum. & Non Ferrous U DE No MELIN ME--604 $13.26 CO 3/8 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1204 $12.64 CO 3/8 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01289 $9.39 C CO 3/8 3/8 3-1/16 CC GP For Alum. & Non Ferrous U DE - YG1 YG-EM11289 $13.29 C CO 3/4 3/8 2-5/8 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1204-L $16.89 HSS 3/8 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $6.90 C CAR 9/16 3/16 2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $11.81 C CO 13/32 3/16 2-1/4 CC GP For Alum. & Non Ferrous U DE No MELIN ME /2 $13.26 CO 3/4 3/16 3/4 CC Miniature -Precision Milling U DE - YG1 YG-EM51266 $10.62 C CAR 5/16 3/16 2 CC Hi Perf For Alum. U DE - IMCO Micrograin IMCO $17.54 C CAR 9/16 3/16 2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $11.81 C HSS 9/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $6.90 C 11/64 CAR 5/8 3/16 2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $11.81 C 3/16 & Larger Sizes Continued On Following Page SINGLE FLUTE ROUTERS FOR ALUMINUM SOLID CARIDE High speed, solid carbide routers for aluminum and non-ferrous cutting applications Optimized rake and clearance angles produce highest material removal rates and improved surface finishes Innovative single flute end mill geometry avoids chip melting and chip re-welding problems.. Flute Length Code 1/16 1/8 1-1/2 1/4 MI-SFA06222 $ /8 1/8 1-1/2 1/4 MI-SFA12522 $ /16 3/16 2 1/2 MI-SFA18733 $ /16 1/4 2 1/4 MI-SFA06242 $ /8 1/4 2 1/4 MI-SFA12542 $ /8 1/4 2 1/2 MI-SFA12544 $ /32 1/4 2 5/8 MI-SFA15645 $ /16 1/4 2 1/2 MI-SFA18744 $ /16 1/4 2 5/8 MI-SFA18745 $ /32 1/4 2-1/2 3/4 MI-SFA21846 $ /4 1/4 2-1/2 3/8 MI-SFA25043 $ /8 3/ /8 MI-SFA37569 $ /2 1/2 3 1 MI-SFA50088 $66.15

113 ENDMILLS-2 FLUTE/SQUARE END 2 FLUTE ENDMILLS SQUARE END (continued) HSS, Cobalt & Carbide For Aluminum, Non-Ferrous Materials & Plastic 2 Flute Square End Endmills (HSS, Cobalt & Carbide)- For Aluminum, Plastic & Non-Ferrous Materials Mill 3/16 Material LOC Cut Application Coating Type Flats Vendor CAR 3/8 3/16 2 CC Hi Perf For Alum. U DE - IMCO Micrograin IMCO $16.27 C CAR 1/2 3/8 3-1/4 CC GP For Alum. & Non Ferrous U DE Yes MELIN ME-MG-1206 $29.53 CAR 5/8 3/16 2 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01565 $8.24 C CO 3/16 3/8 2-1/16 CC Streakers - Hi Perf For Alum U SE Yes MELIN ME-AS-1206 $11.70 CO 7/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $8.15 C CO 7/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1206 $11.70 HSS 7/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE - TMX I $6.90 C CO 7/16 3/8 3-1/8 CC GP For Alum. & Non Ferrous U DE - YG1 YG-EM11293 $13.29 C CO 1/2 3/8 2-11/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AN-1206 $ /64 CAR 5/8 1/4 2-1/2 CC Hi Helix For Alum. U SE - IMCO Micrograin IMCO $14.75 C 7/32 CAR 1/2 1/4 2-1/2 CC GP For Alum. & Non Ferrous U DE - IMCO Micrograin IMCO $21.51 C CAR 5/8 1/4 2-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $14.75 C 15/64 CAR 3/4 1/4 2-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $14.75 C 1/4 CAR 1/2 1/4 2-1/2 CC Hi Perf For Alum. U DE - IMCO Micrograin IMCO $20.66 C CAR 3/4 1/4 2-1/2 CC Streakers - Hi Perf For Alum U SE - IMCO Micrograin IMCO $13.09 C CAR 3/4 1/4 2-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Streaker IMCO $27.24 C CAR 3/4 1/4 2-1/2 CC Streakers - Hi Perf For Alum U SE - YG1 YG-EM01573 $10.39 C CAR 1-1/4 1/4 3 CC GP For Alum. & Non Ferrous U SE - IMCO Streaker IMCO $39.50 C CAR 1-1/2 1/4 4 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM54573 $19.79 C CO 1/2 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $8.12 C CO 1/2 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01297 $9.39 C CO 1/2 3/8 3-1/8 CC GP For Alum. & Non Ferrous U DE - YG1 YG-EM11297 $13.29 C HSS 1/2 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $6.90 C 17/64 CAR 3/4 5/16 2-1/2 CC Hi Helix For Alum. U SE - IMCO Micrograin IMCO $23.02 C 9/32 5/16 3/8 7/16 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 3/4 5/16 2-1/2 CC Hi Perf For Alum. U SE - IMCO Micrograin IMCO $23.02 C CO 9/16 3/8 3-1/8 CC GP For Alum. & Non Ferrous U DE Yes MELIN ME $18.39 CAR 1/2 5/16 2-1/2 CC GP For Alum. & Non Ferrous U DE - IMCO Micrograin IMCO $26.65 C CAR 3/4 3/8 3-1/2 CC Streakers - Hi Perf For Alum U DE No MELIN ME-MG-1210 $39.19 CAR 13/16 5/16 2-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Streaker IMCO $30.68 C CAR 7/8 5/16 2-1/2 CC Streakers - Hi Perf For Alum U SE - IMCO Micrograin IMCO $18.50 C CAR 1-3/8 5/16 3 CC GP For Alum. & Non Ferrous U SE - IMCO Streaker IMCO $50.03 C CO 9/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1210 $11.88 CO 9/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01301 $9.39 C CO 9/16 3/8 3-1/8 CC GP For Alum. & Non Ferrous U DE - YG1 YG-EM11301 $13.29 C CO 3/4 3/8 3-5/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AN-1210 $15.69 HSS 9/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $6.90 C CAR 9/16 3/8 2-1/2 CC Hi Perf For Alum. U DE - IMCO Micrograin IMCO $27.49 C CAR 3/4 3/8 3-1/2 CC GP For Alum. & Non Ferrous U DE No MELIN ME-MG-1212 $40.87 CAR 7/8 3/8 2-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $23.05 C CAR 7/8 3/8 2-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Streaker IMCO $34.32 C CAR 1 3/8 2-1/2 CC Hi Perf For Alum. U SE - YG1 YG-EM01584 $17.39 C CAR 1-1/2 3/8 3-1/4 CC GP For Alum. & Non Ferrous U SE - IMCO Streaker IMCO $46.14 C CO 9/16 3/8 2-1/8 CC GP For Alum. & Non Ferrous U SE Yes TMX I $8.98 CO 9/16 3/8 2-5/16 CC Streakers - Hi Perf For Alum U SE Yes MELIN ME-A-1212 $11.88 CO 9/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01305 $9.39 C CO 9/16 3/8 3-1/8 CC Streakers - Hi Perf For Alum U DE - YG1 YG-EM11305 $13.29 C CO 3/4 3/8 3-5/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AN-1212 $15.61 CO 2-1/2 3/8 4-1/4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1212-E $24.78 HSS 9/16 3/8 2-5/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $6.90 C CAR 1 7/16 2-3/4 XX GP For Alum. & Non Ferrous A SE - IMCO Spector IMCO $37.25 C CO 13/16 3/8 2-1/2 CC GP For Alum. & Non Ferrous U SE Yes TMX I $12.03 C CO 13/16 1/2 3-3/4 CC GP For Alum. & Non Ferrous U DE Yes MELIN ME $28.00 HSS 13/16 3/8 2-1/2 CC GP For Alum. & Non Ferrous U SE Yes TMX I $8.84 C 1/2 & Larger Sizes Continued On Following Page Master Catalog 381 Code CARIDE INSERTS DEURRING

114 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-2 FLUTE/SQUARE END 2 FLUTE ENDMILLS SQUARE END (continued) HSS, Cobalt & Carbide For Aluminum, Non-Ferrous Materials & Plastic 2 Flute Square End Endmills (HSS, Cobalt & Carbide)- For Aluminum, Plastic & Non-Ferrous Materials (continued) Mill 1/2 Material LOC Cut Application Coating Type Flats Vendor Master Catalog CAR 1 1/2 3 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $37.70 C CAR 1 1/2 3 CC Streakers - Hi Perf For Alum U SE - IMCO Streaker IMCO $48.93 C CAR 1 1/2 3 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01593 $28.69 C CAR 2 1/2 4 CC Streakers - Hi Perf For Alum U SE - IMCO Streaker IMCO $79.13 C CO 1/2 3/8 2-3/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AS-1216 $19.40 CO 13/16 1/2 3-3/4 CC GP For Alum. & Non Ferrous U DE - YG1 YG-EM11321 $20.72 C CO 1 1/2 3 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01321 $13.47 C CO 1 1/2 4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AN-1616 $21.99 CO 1-1/4 1/2 3-1/4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AA-1616-M $25.53 CO 1-1/2 1/2 3-1/2 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1616-M $24.13 CO 2 1/2 4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1616-L $24.90 CO 2 1/2 4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AA-1616-L $28.62 CO 3 1/2 5 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1616-E $31.14 CO 1 1/2 3 CC GP For Alum. & Non Ferrous U SE Yes TMX I $12.03 C HSS 1 1/2 3 CC GP For Alum. & Non Ferrous U SE Yes TMX I $9.30 C 17/32 CO 1-1/8 1/2 3-1/8 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1617 $ /16 5/8 11/16 3/4 13/16 7/8 CAR 1-1/8 9/16 3-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $66.79 C CAR 1-1/4 9/16 3-1/2 CC GP For Alum. & Non Ferrous U SE No MELIN ME-AMG-1818 $61.90 CO 1-1/8 1/2 3-1/8 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-1618 $21.93 CAR 1-1/4 5/8 3-1/2 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $72.65 C CAR 1-1/4 5/8 3-1/2 CC Streakers - Hi Perf For Alum U SE - IMCO Streaker IMCO $ C CO 5/8 1/2 2-3/4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AS-1620 $24.64 CO 1-5/16 5/8 3-7/16 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01337 $21.30 C CO 1-3/8 5/8 4-5/8 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AN-2020 $32.53 HSS 1-5/16 5/8 3-7/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $17.63 C CO 1-5/16 5/8 3-7/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2022 $28.53 CO 1-5/16 3/4 5 CC GP For Alum. & Non Ferrous U DE Yes MELIN ME $54.57 CAR 1-1/2 3/4 4 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $ C CO 1-5/16 5/8 3-7/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2024 $28.98 CO 1-5/16 3/4 3-7/16 CC GP For Alum. & Non Ferrous U SE - YG1 YG-EM01359 $23.70 C CO 1-5/16 3/4 3-9/16 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2424 $28.44 CO 1-5/8 3/4 3-7/8 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AA-2424 $36.58 CO 1-5/8 3/4 5-3/8 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AN-2424 $42.05 CO 2-1/4 3/4 4-1/2 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2424-M $40.88 CO 3 3/4 5-1/4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2424-L $49.56 CO 1-5/16 3/4 3-7/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $29.63 C HSS 1-5/16 3/4 3-7/16 CC GP For Alum. & Non Ferrous U SE Yes TMX I $20.36 C CO 1-1/2 5/8 3-5/8 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2026 $37.18 CO 1-1/2 3/4 3-3/4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2426 $38.43 CO 1-9/16 7/8 5-1/2 CC GP For Alum. & Non Ferrous U DE Yes MELIN ME $68.49 HSS 1-1/2 7/8 3-3/4 CC GP For Alum. & Non Ferrous U SE Yes TMX I $27.86 C CAR 1-1/2 7/8 4 CC GP For Alum. & Non Ferrous U SE No MELIN ME-AMG-2828 $ CO 5/8 1/2 2-5/8 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-AS-1628 $40.81 CO 1-1/2 3/4 3-3/4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2428 $38.24 CO 1-9/16 7/8 5-1/2 CC GP For Alum. & Non Ferrous U DE Yes MELIN ME $ /16 CO 1-5/ /8 CC GP For Alum. & Non Ferrous U DE Yes MELIN ME $ /4 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 1-1/2 1 4 CC GP For Alum. & Non Ferrous U SE - IMCO Micrograin IMCO $ C CO 1-5/ /8 CC GP For Alum. & Non Ferrous U SE Yes TMX I $44.92 C CO 1-1/2 7/8 3-3/4 CC GP For Alum. & Non Ferrous U SE Yes MELIN ME-A-2832 $47.98 CO 1-5/ /8 CC Gp For Alum. & Non Ferrous U SE Yes MELIN ME-A-3232 $47.13 HSS 1-5/ /8 CC Gp For Alum. & Non Ferrous U SE Yes TMX I $34.51 C HSS 1-5/8 1-1/4 4-1/8 CC Gp For Alum. & Non Ferrous U SE Yes TMX I $53.93 C CO 1-5/ /8 CC Gp For Alum. & Non Ferrous U SE Yes TMX I $79.57 C Code

115 ENDMILLS-3 FLUTE/SQUARE END 3 FLUTE ENDMILLS SQUARE END Cobalt & Carbide For Finishing Non-Ferrous Materials & Hard Alloys ALSO AVAILALE! 3 Flute Square End Endmills (Cobalt & Carbide)- For Finishing Non-Ferrous Materials & Hard Alloys Mill 1/16 1/8 3/16 7/32 1/4 5/16 3/8 Material LOC Cut Application Helix Angle Coating Type Flats Vendor CAR 1/8 1/8 1-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMGS-402 $7.72 CAR 3/16 1/8 1-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-402 $7.77 CAR 1/4 1/8 1-1/2 CC Stainless Steels 40 A SE - IMCO Enduro IMCO $19.34 C CAR 1/4 1/8 1-1/2 CC Stainless Steels - A SE - YG1 Jet Power YG-EM57558TF $16.42 C CAR 1/4 1/8 1-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMGS-404 $7.19 CAR 1/2 1/8 1-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-404 $7.53 CAR 3/4 1/8 3 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-404-L $11.36 CO 3/8 3/8 2-5/16 CC LLight Mach-Alum./Non Ferrous - U SE Yes MELIN ME-E-1204 $14.52 CAR 5/16 3/16 2 CC Stainless Steels 40 A SE - IMCO Enduro IMCO $21.36 C CAR 3/8 3/16 1-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMGS-606 $9.50 CAR 5/8 3/16 2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-606 $10.67 CAR 3/4 3/16 3 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-606-L $14.45 CO 1/2 3/8 2-3/8 CC Light Mach-Alum./Non Ferrous - U SE Yes MELIN ME-E-1206 $14.52 CAR 3/8 1/4 2 CC Stainless Steels - A SE - YG1 Jet Power YG-EM57570TF $27.60 C CAR 3/4 1/4 2-1/2 CC Stainless Steels - A SE - YG1 Jet Power YG-EM56570TC $29.90 C CAR 3/8 1/4 2 CC Stainless Steels - A SE - YG1 Jet Power YG-EM57573TF $25.27 C CAR 3/8 1/4 2-1/2 CC Stainless Steels 40 A SE IMCO IMCO $24.64 C CAR 1/2 1/4 2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMGS-808 $11.19 CAR 3/4 1/4 2-1/2 CC Gp For Steels - A SE - YG1 Jet Power YG-EM95065 $20.37 C CAR 3/4 1/4 2-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-808 $13.76 CAR 3/4 1/4 2-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG $16.86 CAR 1-1/8 1/4 3 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-808-L $18.24 CO 5/8 3/8 2-7/16 CC Light Mach-Alum./Non Ferrous - U SE Yes MELIN ME-E-1208 $14.90 CAR 7/16 5/16 2 CC Stainless Steels - A SE - YG1 Jet Power YG-EM57579TF $32.97 C CAR 1/2 5/16 2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMGS-1010 $17.23 CAR 13/16 5/16 2-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-1010 $18.14 CAR 1-1/8 5/16 3 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-1010-L $21.22 CO 3/4 3/8 2-1/2 CC Light Mach-Alum./Non Ferrous - U SE Yes MELIN ME-E-1210 $14.90 CAR 1/2 3/8 2 CC Stainless Steels - A SE - YG1 YG-EM83584TF $29.32 C CAR 5/8 3/8 2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMGS-1212 $21.18 CAR 1 3/8 2-1/2 CC GP For Steels - A SE - YG1 Jet Power YG-EM95067 $32.50 C CAR 1 3/8 2-1/2 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-1212 $21.45 CAR 1-1/8 3/8 3 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-1212-L $29.30 CO 3/4 3/8 2-1/2 CC Light Mach-Alum./Non Ferrous - U SE Yes MELIN ME-E-1212 $14.90 HSS 3/4 3/8 2-1/2 CC Hi Helix For Aluminum - U SE - MINICUT MN $15.34 C HSS 1-1/2 3/8 3-1/4 CC Hi Helix For Aluminum - U SE - MINICUT MN $17.54 C 7/16 CAR 1 7/16 2-3/4 CC Light Mach-Alum./Non Ferrous - U SE No MELIN ME-EMG-1414 $ /2 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 5/8 1/2 2-1/2 CC Light Mach-Alum. & Non Ferrous - U SE No MELIN ME-EMGS-1616 $34.72 CAR 5/8 1/2 3 CC Stainless Steels 40 A SE - IMCO EnDuro IMCO $56.29 C CAR 1 1/2 3 CC GP For Steels - A SE - YG1 Jet Power YG-EM95068 $50.55 C CAR 1 1/2 3 CC Light Mach-Alum. & Non Ferrous - U SE No MELIN ME-EMG $46.68 CAR 1-1/4 1/2 3 CC Stainless Steels 40 A SE - IMCO EnDuro IMCO $61.87 C CAR 1-1/4 1/2 3 CC Stainless Steels - A SE - YG1 JetPower YG-EM56593TF $63.34 C CAR 2 1/2 4 CC Light Mach-Alum. & Non Ferrous - U SE No MELIN ME-EMG-1616-L $45.49 CO 1 3/8 2-11/16 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1216 $19.84 HSS 2 1/2 4 CC Hi Helix ForAlum. - U SE - MINICUT MN $23.75 C 9/16 CO 1-3/8 1/2 3-3/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1618 $ Master Catalog 383 Code 5/8 & Larger Sizes Continued On Following Page CARIDE INSERTS DEURRING

116 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-3 FLUTE/SQUARE END 3 FLUTE ENDMILLS (continued) SQUARE END Cobalt & Carbide For Finishing Non-Ferrous Materials & Hard Alloys 3 Flute Square End Endmills (Cobalt & Carbide)- For Finishing Non-Ferrous Materials & Hard Alloys (continued) Mill 5/8 Material LOC Cut Application Helix Angle Coating Type Flats Vendor Master Catalog CAR 3/4 5/8 3 CC Light Mach-Alum. & Non Ferrous - U SE No MELIN ME-EMGS-2020 $60.87 CAR 1-1/4 5/8 3-1/2 CC Light Mach-Alum. & Non Ferrous - U SE No MELIN ME-EMG $87.07 CAR 2-1/4 5/8 5 CC Light Mach-Alum. & Non Ferrous - U SE No MELIN ME-EMG-2020-L $90.41 CAR 3 5/8 6 NC Light Mach-Alum. & Non Ferrous - A SE - IMCO Micrograin IMCO $ C CO 1-3/8 1/2 3-3/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1620 $ /16 CO 1-5/8 1/2 3-5/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1622 $ /4 13/16 CAR 2-1/4 3/4 5 CC Light Mach-Alum. & Non Ferrous - U SE No MELIN ME-EMG-2424-L $ CAR 2-1/4 3/4 5 NC Light Mach-Alum. & Non Ferrous - U SE - IMCO Micrograin IMCO $ C CO 1-5/8 1/2 3-5/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1624 $34.12 HSS 1-5/8 3/4 3-7/8 CC Hi Helix For Alum. - U SE - MINICUT MN $26.22 C CO 1-5/8 1/2 3-5/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1626 $42.58 CO 1-7/8 5/8 4 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-2026 $42.58 CO 1-7/8 3/4 4-1/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-2426 $ /32 CO 1-5/8 1/2 3-5/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1627 $ /8 CO 1-5/8 1/2 3-5/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1628 $44.50 CO 1-7/8 5/8 4 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-2028 $ /16 CO 1-7/8 1/2 3-7/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-1630 $ ALSO AVAILALE! ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 1-1/2 1 4 CC Light Mach-Alum. & Non Ferrous - U SE No MELIN ME-EMG $ CO 1-7/8 3/4 4-1/8 CC Light Mach-Alum. & Non Ferrous - U SE Yes MELIN ME-E-2432 $53.25 HSS /2 CC Hi Helix For Alum. - U SE - MINICUT MN $46.07 C HSS /2 CC Hi Helix For Alum. - U SE - MINICUT MN $54.84 C HSS /2 CC Hi Helix For Alum. - U SE - MINICUT MN $65.81 C HSS /2 CC Hi Helix For Alum. - U SE - MINICUT MN $80.42 C 1-1/4 HSS 4 1-1/4 6-1/2 CC Hi Helix For Alum. - U SE - MINICUT MN $95.05 C METRIC ENDMILLS Square End-Regular Length High speed steel Center cutting Single end 2 & 4 flutes Additional sizes availableplease call for more information 2 FLUTE 4 FLUTE-CENTER CUTTING LOC LOC 3MM 3/8 3/8 2-5/16 I $8.46 3MM 3/8 3/8 2-5/16 I $8.62 4MM 3/8 7/16 2-5/16 I $8.46 4MM 3/8 1/2 2-3/8 I $8.62 5MM 3/8 1/2 2-5/16 I $8.46 5MM 3/8 9/16 2-1/2 I $8.62 6MM 3/8 1/2 2-5/16 I $8.46 6MM 3/8 5/8 2-1/2 I $8.62 7MM 3/8 9/16 2-5/16 I $9.38 7MM 3/8 3/4 2-1/2 I $8.62 8MM 3/8 9/16 2-5/16 I $9.38 8MM 3/8 3/4 2-1/2 I $9.45 9MM 3/8 9/16 2-5/16 I $9.38 9MM 3/8 3/4 2-1/2 I $ MM 3/8 13/16 2-1/2 I $ MM 3/ /16 I $ MM 3/8 13/16 2-1/2 I $ MM 3/ /16 I $ MM 1/2 1-1/8 3-1/8 I $ MM 3/ /16 I $ MM 1/2 1-1/8 3-1/8 I $ MM 1/2 1-1/4 3-1/4 I $ MM 1/2 1-1/8 3-1/8 I $ MM 1/2 1-1/4 3-1/4 I $ MM 1/2 1-1/8 3-1/8 I $ MM 1/2 1-3/8 3-3/8 I $ MM 1/2 1-1/8 3-1/8 I $ MM 5/8 1-5/8 3-3/4 I $ MM 1/2 1-5/16 3-7/16 I $ MM 5/8 1-5/8 3-3/4 I $ MM 5/8 1-1/2 3-3/4 I $ MM 5/8 1-7/8 4-1/8 I $ MM 3/4 1-1/2 3-3/4 I $ MM 3/4 1-7/8 4-1/8 I $ MM 1/ /2 I $ MM 3/ /2 I $32.97 Code

117 ENDMILLS-4 FLUTE/SQUARE END 4 FLUTE ENDMILLS SQUARE END HSS, Cobalt & Carbide For Steels & Stainless Steels 4 Flute Square End Endmills (HSS, Cobalt & Carbide)- For Steels & Stainless Steels Mill Material LOC Cut Application Coating Type Flat Vendor 1/32 CAR 3/32 1/8 1-1/2 NC General Purpose U SE No IMCO IMCO $9.96 C 3/64 CAR 1/8 1/8 1-1/2 NC General Purpose U SE No IMCO IMCO $9.96 C 1/16 5/64 3/32 7/64 1/8 CAR 1/8 1/8 1-1/2 CC General Purpose I DE - IMCO AuCAR IMCO $16.97 C CAR 1/8 1/8 1-1/2 CC General Purpose U DE - IMCO Micrograin IMCO $13.22 C CAR 3/16 1/8 1-1/2 CC GP For Steels L SE - YG1 YG-EM07554TF $7.69 C CAR 3/16 1/8 1-1/2 CC GP For Steels U SE - YG1 YG-EM07554 $5.57 C CAR 3/16 1/8 1-1/2 CC Stainless Steels U SE - YG1 X-Power YG-EM93093 $11.42 C CO 3/16 3/16 1-1/2 NC General Purpose U SE No MELIN ME-C-602 $9.82 CO 3/16 3/16 2-1/4 CC Miniature- Prec. Milling U DE - YG1 YG-EM53256 $9.25 C CO 3/16 3/16 2-1/4 NC General Purpose U DE No MELIN ME-D-602 $13.26 CO 7/32 3/16 2-1/2 NC General Purpose U DE No MELIN ME-D-602-L $18.39 CO 15/64 3/16 2-1/4 NC General Purpose U DE No MELIN ME-D-602-1/2 $13.26 CO 1/4 3/16 1-1/2 NC General Purpose U SE No MELIN ME-C-602-1/2 $9.82 CAR 3/16 1/8 1-1/2 CC GP For Steels U DE - YG1 YG-EM33556 $9.00 C CAR 3/8 1/8 1-1/2 CC GP For Steels L SE - YG1 YG-EM07556TF $7.69 C CAR 3/8 1/8 1-1/2 CC GP For Steels U SE - YG1 YG-EM07556 $5.57 C CO 9/64 3/16 2 NC General Purpose U DE No MELIN ME-DS-603 $12.40 CO 9/32 3/16 2-1/4 NC General Purpose U DE No MELIN ME-D-603 $13.26 CAR 3/8 1/8 1-1/2 CC GP For Steels C SE - YG1 YG-EM07557TC $8.25 C CAR 3/8 1/8 1-1/2 CC GP For Steels L SE - YG1 YG-EM07557TF $8.25 C CO 5/32 3/16 2 NC General Purpose U DE No MELIN ME-DS-603-1/2 $12.40 CAR 1/4 1/8 1-1/2 CC GP For Steels L DE - YG1 YG-EM33558TF $11.25 C CAR 1/4 1/8 1-1/2 CC GP For Steels L SE - YG1 YG-EM31558TF $7.69 C CAR 1/4 1/8 1-1/2 CC GP For Steels U DE - YG1 YG-EM33558 $8.59 C CAR 3/8 3/8 3-1/16 CC GP For Steels U DE - YG1 YG-EM13559 $21.59 C CAR 1/2 1/8 1-1/2 CC GP For Steels C SE - YG1 YG-EM07558TE $7.94 C CAR 1/2 1/8 1-1/2 CC GP For Steels L SE - YG1 YG-EM07558TF $7.69 C CAR 1/2 1/8 1-1/2 CC General Purpose U SE No IMCO Micrograin IMCO $7.91 C CAR 1/2 1/8 1-1/2 CC General Purpose U SE No MELIN ME-CCMG-404 $7.53 CAR 1/2 1/8 1-1/2 CC GP For Steels U SE - YG1 YG-EM07558 $5.57 C CAR 1/2 1/8 1-1/2 CC Stainless Steels U SE - YG1 X-Power YG-EM93094 $11.42 C CO 3/16 3/16 2 NC General Purpose U DE No MELIN ME-DS-604 $12.40 CO 3/8 3/16 2-1/4 NC General Purpose U DE No MELIN ME-D-604 $13.26 CO 3/8 3/8 2-5/16 CC GP For Steels U SE - YG1 YG-EM07289 $10.72 C CO 3/8 3/8 3-1/16 CC GP For Steels U DE - YG1 YG-EM13289 $14.89 C CO 3/8 3/8 2-5/16 CC General Purpose U SE Yes TMX I $9.11 C CO 1/2 3/8 3-1/4 CC General Purpose U DE Yes MELIN ME-DD-1204-M $19.65 CO 5/8 3/8 3-9/16 CC General Purpose U DE Yes MELIN ME-DD-1204-L $20.97 HSS 3/8 3/8 2-5/16 CC General Purpose U SE Yes TMX I $7.30 C 9/64 CO 27/64 3/16 2-1/4 NC General Purpose U DE No MELIN ME-D-604-1/2 $ /32 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 5/16 3/16 2 CC GP For Steels U DE - YG1 YG-EM33561 $12.02 C CAR 9/16 3/16 2 CC GP For Steels L SE - YG1 YG-EM07561TF $10.97 C CAR 9/16 3/16 2 CC GP For Steels U SE - YG1 YG-EM07561 $8.24 C CO 15/64 3/16 2 NC General Purpose U DE No MELIN ME-DS-605 $12.40 CO 7/16 3/8 2-5/16 CC General Purpose U SE Yes MELIN ME-CC-1205 $12.45 CO 5/8 3/8 2-1/2 CC General Purpose U SE Yes MELIN ME-CC-1205-M $17.05 CO 3/4 3/8 2-5/8 CC General Purpose U SE Yes MELIN ME-CC-1205-L $17.65 CO 3/8 3/8 2-5/16 CC General Purpose U SE Yes TMX I $9.11 C HSS 3/8 3/8 2-5/16 CC General Purpose U SE Yes TMX I $7.30 C 11/64 & Larger Sizes Continued On Following Page Master Catalog 385 Code CARIDE INSERTS DEURRING

118 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-4 FLUTE/SQUARE END 4 FLUTE ENDMILLS (continued) SQUARE END HSS, Cobalt & Carbide For Steels & Stainless Steels 4 Flute Square End Endmills (HSS, Cobalt & Carbide)- For Steels & Stainless Steels (continued) Mill Material LOC Cut Application Coating Type Flats Vendor Master Catalog 11/64 CAR 5/8 3/16 2 CC General Purpose U SE No IMCO Micrograin IMCO $11.81 C 3/16 CAR 3/8 3/16 2 CC GP For Steels L DE - YG1 YG-EM33565TF $15.45 C CAR 3/8 3/16 2 CC GP For Steels U DE - YG1 YG-EM33565 $12.02 C CAR 1/2 3/8 3-1/4 CC General Purpose U DE Yes MELIN ME-DDMG-1206 $29.53 CAR 1/2 3/8 3-1/4 CC GP For Steels U DE - YG1 YG-EM13567 $23.67 C CAR 5/8 3/16 2 CC GP For Steels L SE - YG1 YG-EM07565TE $11.27 C CAR 5/8 3/16 2 CC GP For Steels L SE - YG1 YG-EM07565TF $10.97 C CAR 5/8 3/16 2 CC GP For Steels U SE - YG1 YG-EM07565 $8.24 C CAR 5/8 3/16 2 CC Stainless Steels U SE - YG1 X-Power YG-EM93095 $12.82 C CAR 5/8 3/16 2 NC General Purpose A SE - IMCO Spector IMCO $13.62 C CO 3/16 3/8 2-1/16 CC General Purpose U SE Yes MELIN ME-CCS-1206 $12.21 CO 9/32 3/8 2-3/4 CC General Purpose U DE Yes MELIN ME-DDS-1206 $15.51 CO 1/2 3/8 2-3/8 CC General Purpose U SE Yes TMX I $9.11 C CO 1/2 3/8 2-3/8 CC GP For Steels U SE - YG1 YG-EM07293 $10.72 C CO 1/2 3/8 3-1/4 CC GP For Steels U DE - YG1 YG-EM13293 $14.89 C CO 3/4 3/8 2-5/8 CC General Purpose U SE Yes MELIN ME-CC-1206-L $17.65 CO 7/8 3/8 4-1/8 CC General Purpose U DE Yes MELIN ME-DD-1206-L $20.93 CO 1-1/4 3/8 3-1/8 CC General Purpose U SE Yes MELIN ME-CC-1206-E $20.61 HSS 1/2 3/8 2-3/8 CC General Purpose U SE Yes TMX I $7.30 C 13/64 CAR 5/8 1/4 2-1/2 CC General Purpose U SE No IMCO Micrograin IMCO $14.75 C 7/32 CAR 5/8 1/4 2-1/2 CC GP For Steels L SE - YG1 YG-EM07570TF $14.60 C CO 5/8 3/8 2-7/16 CC GP For Steels U SE Yes TMX I $9.11 C HSS 5/8 3/8 2-7/16 CC General Purpose U SE Yes TMX I $7.30 C CO 1/4 3/8 2-3/16 CC General Purpose U SE Yes MELIN ME-CCS-1207 $12.64 CO 1/2 3/8 2-3/8 CC General Purpose U SE Yes MELIN ME-CC-1207 $12.45 CO 7/8 3/8 2-3/4 CC General Purpose U SE Yes MELIN ME-CC-1207-M $17.05 CO 1-1/4 3/8 3-1/8 CC General Purpose U SE Yes MELIN ME-CC-1207-L $17.65 CO 1-1/2 3/8 3-5/16 CC General Purpose U SE Yes MELIN ME-CC-1207-E $ /64 CAR 3/4 1/4 2-1/2 CC General Purpose U SE No IMCO Micrograin IMCO $14.75 C 1/4 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 1/2 1/4 2 CC GP For Steels L SE - YG1 YG-EM31573TF $14.60 C CAR 1/2 1/4 2-1/2 CC General Purpose I DE - IMCO AuCAR IMCO $26.78 C CAR 1/2 1/4 2-1/2 CC GP For Steels L DE - YG1 YG-EM33573TF $21.00 C CAR 1/2 1/4 2-1/2 CC GP For Steels U DE - YG1 YG-EM33573 $14.02 C CAR 3/4 1/4 2-1/2 CC GP For Steels C SE - YG1 YG-EM07573TC $14.60 C CAR 3/4 1/4 2-1/2 CC GP For Steels C SE - YG1 YG-EM07573TE $15.07 C CAR 3/4 1/4 2-1/2 CC GP For Steels L SE - YG1 YG-EM07573TF $14.60 C CAR 3/4 1/4 2-1/2 CC General Purpose U SE No MELIN ME-CCMG-808 $13.76 CAR 3/4 1/4 2-1/2 CC GP For Steels U SE - YG1 YG-EM07573 $10.39 C CAR 3/4 1/4 2-1/2 CC Stainless Steels U SE - YG1 X-Power YG-EM93096 $15.60 C CAR 1-1/8 1/4 3 CC GP For Steels L SE - YG1 YG-EM08573TF $18.14 C CAR 1-1/2 1/4 4 NC General Purpose A SE - IMCO Spector IMCO $29.52 C CO 1/4 3/8 2-1/8 CC General Purpose U SE Yes MELIN ME-CCS-1208 $12.21 CO 5/8 3/8 2-7/16 CC General Purpose U SE Yes TMX I $9.11 C CO 5/8 3/8 2-7/16 CC GP For Steels U SE - YG1 YG-EM07297 $10.72 C CO 5/8 3/8 2-7/16 NC GP For Steels U SE - YG1 YG-EM04297 $9.39 C CO 5/8 3/8 3-3/8 CC GP For Steels U DE - YG1 YG-EM13297 $14.89 C CO 5/8 3/8 3-3/8 NC GP For Steels U DE - YG1 YG-EM12297 $13.29 C CO 7/8 3/8 2-11/16 CC General Purpose U SE Yes MELIN ME-CC-1208-M $17.05 CO 1-1/4 3/8 3-1/16 CC GP For Steels U SE - YG1 YG-EM08297 $13.95 C CO 1-3/4 3/8 3-9/16 CC General Purpose U SE Yes MELIN ME-CC-1208-E $20.01 HSS 5/8 3/8 2-7/16 CC General Purpose U SE Yes TMX I $7.30 C 17/64 & Larger Sizes Continued On Following Page Code

119 ENDMILLS-4 FLUTE/SQUARE END 4 FLUTE ENDMILLS (continued) SQUARE END HSS, Cobalt & Carbide For Steels & Stainless Steels ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated 4 Flute Square End Endmills (HSS, Cobalt & Carbide)- For Steels & Stainless Steels (continued) Mill Material LOC Cut Application Coating Type Flats Vendor 17/64 CAR 3/4 5/16 2-1/2 CC General Purpose U SE No IMCO Micrograin IMCO $23.02 C 9/32 5/16 CO 3/4 3/8 2-1/2 CC General Purpose U SE Yes TMX I $9.11 C CO 1 3/8 2-3/4 CC General Purpose U SE Yes MELIN ME-CC-1209-M $17.65 CO 1-3/4 3/8 3-5/8 CC General Purpose U SE Yes MELIN ME-CC-1209-E $22.23 CAR 1/2 5/16 2-1/2 CC General Purpose I DE - IMCO AuCAR IMCO $35.37 C CAR 3/4 3/8 3-1/2 CC General Purpose U DE Yes MELIN ME-DDMG-1210 $39.19 CAR 13/16 5/16 2-1/2 CC GP For Steels L SE - YG1 YG-EM07579TF $20.87 C CAR 13/16 5/16 2-1/2 CC GP For Steels U SE - YG1 YG-EM07579 $12.57 C CAR 13/16 5/16 2-1/2 CC Stainless Steels U SE - YG1 X-Power YG-EM93097 $22.54 C CAR 7/8 5/16 2-1/2 CC General Purpose I SE No IMCO AuCAR IMCO $23.68 C CO 5/16 3/8 2-1/16 CC General Purpose U SE Yes MELIN ME-CCS-1210 $12.76 CO 3/4 3/8 2-1/2 CC General Purpose U SE Yes TMX I $10.32 C CO 3/4 3/8 2-1/2 CC GP For Steels U SE - YG1 YG-EM07301 $10.72 C CO 3/4 3/8 3-1/2 CC GP For Steels U DE - YG1 YG-EM13301 $14.89 C HSS 3/4 3/8 2-1/2 CC General Purpose U SE Yes TMX I $7.30 C CO 1-3/8 3/8 3-1/8 CC General Purpose U SE Yes MELIN ME-CC-1210-L $16.75 CO 2 3/8 3-3/4 CC General Purpose U SE Yes MELIN ME-CC-1210-E $ /64 CO 3/4 3/8 3-1/2 CC General Purpose U DE Yes MELIN ME-DD /2 $ /32 3/8 13/32 CO 3/8 3/8 2-1/8 CC General Purpose U SE Yes MELIN ME-CCS-1211 $12.76 CO 3/4 3/8 2-1/2 CC General Purpose U SE Yes TMX I $10.32 CO 1 3/8 2-3/4 CC General Purpose U SE Yes MELIN ME-CC-1211-M $17.05 CO 1-1/2 3/8 3-1/4 CC General Purpose U SE Yes MELIN ME-CC-1211-L $17.90 HSS 3/4 3/8 2-1/2 CC General Purpose U SE Yes TMX I $7.30 C CAR 9/16 3/8 2-1/2 CC General Purpose I DE - IMCO AuCAR IMCO $36.88 C CAR 3/4 3/8 3-1/2 CC General Purpose U DE Yes MELIN ME-DDMG-1212 $40.87 CAR 7/8 3/8 2-1/2 CC General Purpose I SE No IMCO AuCAR IMCO $28.34 C CAR 1 3/8 2-1/2 CC GP For Steels C SE - YG1 YG-EM07584TE $26.60 C CAR 1 3/8 2-1/2 CC GP For Steels L SE - YG1 YG-EM07584TF $25.69 C CAR 1 3/8 2-1/2 CC GP For Steels U SE - YG1 YG-EM07584 $17.39 C CAR 1 3/8 2-1/2 CC Stainless Steels U SE - YG1 X-Power YG-EM93098 $26.67 C CAR 1 3/8 2-1/2 CC General Purpose A SE - IMCO Spector IMCO $34.27 C CAR 1 3/8 2-1/2 CC General Purpose A SE - IMCO Spector IMCO $34.27 C CO 3/8 3/8 2-1/8 CC General Purpose U SE Yes MELIN ME-CCS-1212 $12.76 CO 3/4 3/8 2-1/2 CC GP For Steels U SE - YG1 YG-EM07305 $10.72 C CO 3/4 3/8 2-1/2 NC GP For Steels U SE - YG1 YG-EM04305 $9.39 C CO 3/4 3/8 3-1/2 CC GP For Steels U DE - YG1 YG-EM13305 $14.89 C CO 3/4 3/8 3-1/2 NC GP For Steels U DE - YG1 YG-EM12305 $13.29 C CO 1 3/8 2-3/4 CC General Purpose U SE Yes MELIN ME-CC-1212-M $16.26 CO 3/4 3/8 2-1/2 CC General Purpose U SE Yes TMX I $10.18 C HSS 3/4 3/8 2-1/2 CC General Purpose U SE - TMX I $7.30 C CO 1 3/8 2-11/16 CC General Purpose U SE Yes TMX I $12.26 C CO 1 3/8 2-11/16 CC General Purpose U SE Yes MELIN ME-CC-1213 $17.77 HSS 1 3/8 2-11/16 CC General Purpose U SE Yes TMX I $11.33 C Master Catalog 387 Code 7/16 & Larger Sizes Continued On Following Page CARIDE INSERTS DEURRING

120 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-4 FLUTE/SQUARE END 4 FLUTE ENDMILLS (continued) SQUARE END HSS, Cobalt & Carbide For Steels & Stainless Steels 4 Flute Square End Endmills (HSS, Cobalt & Carbide)- For Steels & Stainless Steels (continued) Mill 7/16 15/32 1/2 17/32 9/16 5/8 11/16 Material LOC Cut Application Coating Type Flats Vendor Master Catalog ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 1 7/16 2-3/4 CC General Purpose L SE - TMX I $26.45 C CAR 1 7/16 2-3/4 CC General Purpose U SE No MELIN ME-CCMG-1414 $28.98 CAR 1 7/16 2-3/4 CC General Purpose A SE - IMCO Spector IMCO $37.25 C CAR 1 7/16 2-3/4 CC General Purpose I SE - IMCO AuCAR IMCO $37.02 C CO 1 3/8 2-11/16 CC General Purpose U SE Yes MELIN ME-CC-1214 $17.77 CO 1 3/8 2-11/16 CC General Purpose U SE - MINICUT MN $23.39 C CO 1 3/8 2-11/16 CC GP For Steels U SE - YG1 YG-EM07312 $16.07 C CO 1 3/8 2-11/16 CC General Purpose U SE Yes TMX I $12.93 C CO 1-3/4 1/2 3-3/4 CC General Purpose U SE Yes MELIN ME-CC-1614-L $29.94 HSS 1 3/8 2-11/16 CC General Purpose U SE Yes TMX I $11.33 C CO 1 3/8 2-11/16 CC General Purpose U SE Yes TMX I $12.93 C CO 1-1/4 1/2 3-1/4 CC General Purpose U SE Yes MELIN ME-CC-1615 $20.40 CAR 5/8 1/2 3 CC General Purpose I DE - IMCO AuCAR IMCO $59.64 C CAR 1 1/2 3 CC GP For Steels C SE - YG1 YG-EM07593TE $40.14 C CAR 1 1/2 3 CC GP For Steels C SE - YG1 YG-EM07593TN $35.19 C CAR 1 1/2 3 CC GP For Steels L SE - YG1 YG-EM07593TF $38.99 C CAR 1 1/2 3 CC GP For Steels U SE - YG1 YG-EM07593 $28.69 C CAR 1 1/2 3 CC Stainless Steels U SE - YG1 X-Power YG-EM93099 $42.50 C CAR 1 1/2 3 CC General Purpose A SE - IMCO Spector IMCO $54.75 C CAR 2 1/2 4 CC GP For Steels L SE - YG1 YG-EM08593TF $52.30 C CAR 2 1/2 4 CC GP For Steels U SE - YG1 YG-EM08593 $38.92 C CO 1 3/8 2-11/16 CC General Purpose U SE Yes MELIN ME-CC-1216 $17.77 CO 1 1/2 4-1/8 CC GP For Steels U DE - YG1 YG-EM13321 $21.72 C CO 1 1/2 4-1/8 NC GP For Steels U DE - YG1 YG-EM12321 $20.72 C CO 1-1/4 1/2 3-1/4 CC General Purpose U SE Yes MELIN ME-CC-1616 $17.06 CO 1-1/4 1/2 3-1/4 CC General Purpose U SE Yes MINICUT MN $23.48 C CO 1-1/4 1/2 3-1/4 CC GP For Steels U SE - YG1 YG-EM07321 $16.07 C CO 1-1/4 1/2 3-1/4 NC GP For Steels U SE - YG1 YG-EM04321 $13.47 C CO 1-5/8 1/2 3-5/8 CC General Purpose U SE Yes MELIN ME-CC-1616-M $23.46 CO 2 1/2 4 CC General Purpose U SE Yes MELIN ME-CC-1616-L $22.88 CO 2 1/2 4 CC General Purpose U SE - MINICUT MN $28.79 C CO 2 1/2 4 CC General Purpose U SE Yes MINICUT MN $28.79 C CO 1-1/4 1/2 3-1/4 CC General Purpose U SE Yes TMX I $14.56 C HSS 1-1/4 1/2 3-1/4 CC General Purpose U SE Yes TMX I $11.33 C HSS 1-1/4 1/2 3-1/4 CC General Purpose L SE - MINICUT MNTA $48.09 C HSS 2 1/2 4 CC General Purpose L SE - MINICUT MNTA $61.58 C CO 1-3/8 1/2 3-3/8 CC General Purpose U SE Yes MELIN ME-CC-1617 $24.26 CO 1-3/8 5/8 5 CC General Purpose U DE Yes MELIN ME-DD-2017 $40.24 CAR 1-1/8 9/16 3-1/2 CC General Purpose I SE No IMCO AuCAR IMCO $77.50 C CAR 1-1/8 9/16 3-1/2 CC General Purpose U SE No IMCO Micrograin IMCO $66.79 C CAR 1-1/4 9/16 3-1/2 CC General Purpose U SE No MELIN ME-CCMG-1818 $61.90 CO 1-3/8 1/2 3-3/8 CC General Purpose U SE Yes MELIN ME-CC-1618 $24.26 CO 1-3/8 1/2 3-3/8 CC General Purpose U DE Yes TMX I $24.26 C CO 2-1/2 1/2 4-1/2 CC General Purpose U SE Yes MELIN ME-CC-1618-L $34.12 HSS 1-3/8 1/2 3-3/8 CC General Purpose U SE Yes TMX I $17.47 C CAR 1-1/4 5/8 3-1/2 CC General Purpose I SE No IMCO AuCAR IMCO $84.63 C CAR 1-1/4 5/8 3-1/2 CC GP For Steels L SE - YG1 YG-EM07595TF $69.39 C CAR 1-1/4 5/8 3-1/2 CC GP For Steels U SE - YG1 YG-EM07595 $54.52 C CO 1-5/8 5/8 3-3/4 CC General Purpose U SE Yes TMX I $24.26 C CO 1-3/8 1/2 3-3/8 CC General Purpose U SE Yes MELIN ME-CC-1620 $25.65 CO 1-5/8 5/8 3-3/4 CC GP For Steels U SE - YG1 YG-EM07337 $24.57 C CO 1-5/8 5/8 3-3/4 NC GP For Steels U SE - YG1 YG-EM04337 $21.30 C CO 2 5/8 4-1/8 CC General Purpose U SE Yes MELIN ME-CC-2020-M $32.52 CO 2-1/2 5/8 4-5/8 CC General Purpose U SE Yes MELIN ME-CC-2020-L $33.74 HSS 1-5/8 5/8 3-3/4 CC General Purpose U SE Yes TMX I $19.53 C CO 1-5/8 1/2 3-5/8 CC General Purpose U SE Yes TMX I $28.32 C CO 1-5/8 5/8 3-3/4 CC General Purpose U SE Yes MELIN ME-CC-2022 $ /4 & Larger Sizes Continued On Following Page Code

121 ENDMILLS-4 FLUTE/SQUARE END 4 FLUTE ENDMILLS (continued) SQUARE END HSS, Cobalt & Carbide For Steels & Stainless Steels 4 Flute Square End Endmills (HSS, Cobalt & Carbide)- For Steels & Stainless Steels (continued) Mill 3/4 13/16 7/8 15/16 1 Material LOC Cut Application Coating Type Flats Vendor CAR 1-1/2 3/4 4 CC General Purpose I SE No IMCO AuCAR IMCO $ C CAR 1-1/2 3/4 4 CC GP For Steels L SE - YG1 YG-EM07598TF $98.09 C CAR 1-1/2 3/4 4 CC General Purpose U SE No IMCO Micrograin IMCO $ C CAR 1-1/2 3/4 4 CC General Purpose U SE No MELIN ME-CCMG-2424 $ CAR 1-1/2 3/4 4 CC GP For Steels U SE - YG1 YG-EM07598 $80.49 C CAR 1-1/2 3/4 4 CC Stainless Steels U SE - YG1 X-Power YG-EM93101 $ C CO 1-1/2 3/4 3-3/4 CC General Purpose L SE No TMX I $73.40 C CO 1-5/8 5/8 3-3/4 CC General Purpose U SE Yes MELIN ME-CC-2024 $34.54 CO 1-5/8 3/4 3-7/8 CC General Purpose U SE Yes MELIN ME-CC-2424 $33.43 CO 1-5/8 3/4 3-7/8 CC General Purpose U SE - MINICUT MN $34.45 C CO 1-5/8 3/4 3-7/8 CC GP For Steels U SE - YG1 YG-EM07359 $29.05 C CO 1-5/8 3/4 3-7/8 NC GP For Steels U SE - YG1 YG-EM04359 $23.70 C CO 1-5/8 3/4 5-5/8 CC General Purpose U DE Yes MELIN ME-DD-2424 $48.51 CO 1-5/8 3/4 5-5/8 CC GP For Steels U DE - YG1 YG-EM13359 $42.95 C CO 2-1/4 3/4 4-1/2 CC General Purpose U SE Yes MELIN ME-CC-2424-M $41.82 CO 1-5/8 3/4 3-3/4 CC General Purpose U SE Yes TMX I $31.56 C CO 4 3/4 6-1/4 CC General Purpose U SE Yes MELIN ME-CC-2424-E $57.48 CO 6 3/4 8-1/4 CC General Purpose U SE Yes MELIN ME-CC-2424-EE $76.58 HSS 1-5/8 3/4 3-3/4 CC General Purpose U SE - TMX I $22.45 C HSS 1-5/8 3/4 3-7/8 CC Inconel, Stainless & Steels U SE - MINICUT MN $69.73 C HSS 1-5/8 3/4 3-7/8 CC Titanium U SE - MINICUT MN $69.73 C CO 1-7/8 3/4 4-1/8 CC General Purpose U SE Yes MELIN ME-CC-2426 $39.54 CO 1-7/8 3/4 4-1/8 CC General Purpose U SE Yes TMX I $36.39 C CO 1-7/8 7/8 4-1/8 CC General Purpose U SE Yes MELIN ME-CC-2828 $44.18 CO 1-7/8 7/8 4-1/8 CC General Purpose U SE Yes TMX I $37.22 C CO 5 7/8 7-1/4 CC General Purpose U SE Yes MELIN ME-CC-2828-E $78.68 HSS 1-7/8 3/4 4-1/8 CC General Purpose U SE Yes TMX I $34.14 C CO 1-7/8 7/8 4-1/8 CC General Purpose U SE Yes MELIN ME-CC-2830 $49.51 CAR 1-1/2 1 4 CC General Purpose I SE No IMCO AuCAR IMCO $ C CO /2 CC GP For Steels U SE - YG1 YG-EM07426 $44.00 C CO /2 NC GP For Steels U SE - YG1 YG-EM04426 $37.80 C CO /2 CC General Purpose U SE Yes MELIN ME-CC-3232-M $70.34 CO /2 CC General Purpose U SE Yes MELIN ME-CC-3232-L $77.64 CO /2 CC General Purpose U SE Yes TMX I $47.96 C 1-1/8 CO /2 CC General Purpose U SE Yes MELIN ME-CC-3236 $ /4 1-1/2 2 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CO 2 1-1/4 4-1/2 CC General Purpose U SE Yes TMX I $87.40 C CO 4 1-1/4 6-1/2 CC General Purpose U SE Yes MELIN ME-CC-4040-L $ CO 2 1-1/4 4-1/2 CC General Purpose U SE Yes TMX I $ C HSS 4 1-1/4 6-1/2 CC General Purpose U SE Yes MELIN ME-CC-4048-L $ HSS 2 1-1/4 4-1/2 NC General Purpose U SE Yes TMX I $96.28 C CO 4 1-1/4 6-1/2 CC General Purpose U SE Yes MELIN ME-CCP-4064-L $ EXTRA LONG LENGTH 4 FLUTE ENDMILLS M42 Cobalt Center Cutting 4 flutes, single end M42 8% cobalt offers increased wear and heat resistance for abrasive and difficult materials Center cutting-allows for plunge cutting into solid material Longer length ideal for deeper milling applications NEW ITEM! Master Catalog 389 LOC Code 1/4 3/8 1-3/4 3-9/16 MCT $ /32 3/8 1-3/4 3-3/4 MCT $ /16 3/ /4 MCT $ /32 3/8 2-1/2 4-1/4 MCT $ /8 3/8 2-1/2 4-1/4 MCT $ /32 3/8 2-3/4 4-1/2 MCT $ /16 1/2 2-3/4 4-3/4 MCT $ /2 1/2 3 5 MCT $ /8 5/ /8 MCT $ /4 3/ /4 MCT $ /2 MCT $ CARIDE INSERTS DEURRING

122 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS-5 & 6 FLUTE/SQUARE END 5 & 6 FLUTE ENDMILLS SQUARE END Cobalt & Carbide For Steels & Stainless Steels 5 Flute Square End Endmills (Cobalt & Carbide)- For Steels & Stainless Steels Mill Material LOC Cut Application Coating Type Flats Vendor 1/8 CAR 1/2 1/8 1-1/2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-404 $ /32 CAR 9/16 3/16 2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-605 $ /16 CAR 9/16 3/16 2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-606 $ /32 CAR 3/4 1/4 2-1/2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-807 $ /4 CAR 3/4 1/4 2-1/2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-808 $18.60 CAR 1-1/2 1/4 4 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-808-E $ /16 CAR 13/16 5/16 2-1/2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-1010 $ /8 CAR 1 3/8 2-1/2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-1212 $29.02 CAR 1-3/4 3/8 4 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-1212-E $ /2 CAR 3 1/2 6 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-1616-E $ /16 CAR 1-1/4 9/16 3-1/2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-1818 $ /8 CAR 1-1/4 5/8 3-1/2 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-2020 $ /4 CAR 1-1/2 3/4 4 CC Stainless Steels/High Tensile Steels U SE No MELIN ME-GMG-2424 $ Flute Square End Endmills (Cobalt & Carbide)- For Steels & Stainless Steels Mill 1 ALSO AVAILALE! ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt Material LOC Cut Application Coating Type Flats Vendor I= TiN Coated C= TiCN Coated CO /2 CC General Purpose U SE Yes TMX I $47.96 C CO /2 CC General Purpose U SE - MINICUT MN A $89.95 C HSS /2 CC Titanium U SE - MINICUT MN A $ C 1-1/4 CO 2 1-1/4 4-1/2 CC General Purpose U SE Yes TMX I $87.40 C 1-1/2 CO 2 1-1/4 4-1/2 CC General Purpose U SE Yes TMX I $ C 1-5/8 CO 2 1-1/4 4-1/2 CC General Purpose U SE Yes TMX I $ C 2 CO 2 1-1/4 4-1/2 CC General Purpose U SE Yes TMX I $ C GENERAL ENDMILL INFORMATION Code Code ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD General Information for Endmill Usage: The Following factors should be kept in mind when using the recommended starting feed per tooth. Use Higher Feeds For: Heavy, roughing cuts Rigid set-ups Easy-to-machine work materials Rugged cutters Slab milling cuts Low tensile strength materials Coarse tooth cutters Abrasive materials Use Lower Feeds For: Light, and finishing cuts Frail set-ups Hard to machine work materials Frail and small cutters Deep slots High tensile strength materials Fine tooth cutters Master Catalog To Calculate Given Formula Surface Speed in Feet per Minute = SFM Tool (inches) = D SFM= Revolutions per Minute = RPM (D x x RPM) / 12 Revolutions per Minute = RPM Tool (inches) = D RPM= Surface Speed in Feet per Minute = SFM (SFM x 12) / (D x ) Feed in Inches per Minute = FM Feed Per Revolution in inches = FR Revolutions per Minute = RPM FR = FM / RPM Feed Per Revolution in inches = FR Feed in Inches per Minute = FM Revolutions per Minute = RPM FM = FR x RPM of Teeth in Tool = T of Cutting Teeth per Minute = TM Revolutions per Minute = RPM TM = T x RPM of Teeth in Tool = T Feed Per Tooth = FT Feed Per Revolution in inches = FR FT = FR / T of Teeth in Tool = T Feed Per Tooth = FT Feed in Inches per Minute = FM Revolutions per Minute = RPM FT = FM / (T x RPM)

123 SOLID CARIDE END MILLS HIGH SPIRAL END MILLS 3 & 4 Flute - Single End - 60 Helix These high spiral end mills feature 60 helix for high volume metal removal even in the most difficult applications. Sizes 3/8 and larger feature Weldon Flat. HIGH HELIX END MILLS 6 Flute-Center Cutting-Single End - 38 Helix Cutter Flute 3-Flute 4-Flute Len. 1/4 1/4 2-1/2 3/4 MI-SDH $ /32 5/16 2-1/2 3/4 MI-SDH $ /16 5/16 2-1/2 13/16 MI-SDH31203 MI-SDH31204 $ /8 3/8 2-1/2 7/8 MI-SDH37503 MI-SDH37504 $ /16 7/16 2-1/2 1 MI-SDH43703 MI-SDH43704 $ /2 1/2 3 1 MI-SDH50003 MI-SDH50004 $ /16 9/16 3-1/2 1-1/4 MI-SDH56203 MI-SDH56204 $ /8 5/8 3-1/2 1-1/4 MI-SDH62503 MI-SDH62504 $ /4 3/ /2 MI-SDH75003 MI-SDH75004 $ /2 MI-SDH00003 MI-SDH00004 $ /2 MI-SDH00103 MI-SDH00104 $ LONG REACH END MILLS 2 & 4 Flute Center Cutting - 30 Helix These high helix end mills have a 38 helix to provide superior finish in all finish milling applications, including heat treated materials to 65 Rc. Sizes 3/8 and larger feature Weldon Flat. Cutter Flute Len. 1/4 1/4 2-1/2 3/4 MI-EMH25006 $ /32 5/16 2-1/2 3/4 MI-EMH28106 $ /16 5/16 2-1/2 13/16 MI-EMH31206 $ /8 3/8 2-1/2 7/8 MI-EMH37506 $ /16 7/16 2-1/2 1 MI-EMH43706 $ /2 1/2 3 1 MI-EMH50006 $ /8 5/8 3-1/2 1-1/4 MI-EMH62506 $ /4 3/ /2 MI-EMH75006 $ /2 MI-EMH00006 $ /2 MI-EMH00106 $ HIGH TECH END MILLS 2 Flute - Center Cutting Single Ended - 45 Helix These 2 flute high tech end mills featuring 45 helix for high speed milling of aluminum and soft, non-ferrous materials. Sizes 3/8 and larger feature Weldon Flat. Stub Length Cutter Flute Len. 1/6 1/8 1-1/2 1/8 MI-ASM0622 $ /32 1/8 1-1/2 3/16 MI-ASM0932 $ /8 1/8 1-1/2 1/4 MI-ASM1252 $ /32 3/16 1-1/2 5/16 MI-ASM1562 $ /16 3/16 1-1/2 3/8 MI-ASM1872 $ /32 1/4 2 7/16 MI-ASM2182 $ /4 1/4 2 1/2 MI-ASM2502 $ /32 5/16 2 1/2 MI-ASM2812 $ /16 5/16 2 1/2 MI-ASM3122 $ /8 3/8 2 5/8 MI-ASM3752 $ /16 7/16 2-1/2 5/8 MI-ASM4372 $ /2 1/2 2-1/2 5/8 MI-ASM5002 $53.75 DIAMOND PLATE SPONGECOTE Anti-Fatigue Mats-No. 415 mond-plate SpongeCote is the most popular anti-fatigue mat in the industry because no other offers such a complete package of exceptional comfort, long life, and a high-tech, industrial image. Its exceptionally resilient Nitricell sponge base defines the mat by providing true comfort, enhancing productivity, and reviving morale, all while relieving fatigue throughout the day. lack/yellow Trim lack Cutter Flute Len Master Catalog 391 Ne ck Len. 2-Flute 4-Flute 3/16 3/16 3 3/8 1-5/8 MI-GLR1872 MI-GLR1874 $ /4 1/4 4 1/2 2 MI-GLR2502 MI-GLR2504 $ /16 5/16 4 5/8 2 MI-GLR3122 MI-GLR3124 $ /8 3/8 4 3/4 2 MI-GLR3752 MI-GLR3754 $ /16 7/ /2 MI-GLR4372 MI-GLR4374 $ /2 1/ /2 MI-GLR5002 MI-GLR5004 $ /8 5/ /4 3-1/4 MI-GLR6252 MI-GLR6254 $ /4 3/ /2 3 MI-GLR7502 MI-GLR7504 $ /2 3 MI-GLR0012 MI-GLR0014 $ Regular Length Cutter Flute Len. 1/6 1/8 1-1/2 3/16 MI-ARM0622 $ /32 1/8 1-1/2 3/8 MI-ARM0932 $ /8 1/8 1-1/2 1/2 MI-ARM1252 $ /32 3/16 2 9/16 MI-ARM1562 $ /16 3/16 2 5/8 MI-ARM1872 $ /32 1/4 2-1/2 5/8 MI-ARM2182 $ /4 1/4 2-1/2 3/4 MI-ARM2502 $ /32 5/16 2-1/2 3/4 MI-ARM2812 $ /16 5/16 2-1/2 13/16 MI-ARM3122 $ /8 3/8 2-1/2 7/8 MI-ARM3752 $ /16 7/16 2-1/2 1 MI-ARM4372 $ /2 1/2 3 1 MI-ARM5002 $ /16 9/16 3-1/2 1-1/4 MI-ARM5622 $ /8 5/8 3-1/2 1-1/4 MI-ARM6252 $ /16 3/ /8 MI-ARM6872 $ /4 3/ /2 MI-ARM7502 $ /2 MI-ARM0012 $ For use in dry work areas Anti-fatigue Nitricell sponge base for unparalleled comfort Safety beveled edges Slip and wear resistant 3 Year Warranty EST SELLER! Ideal For Heavily Trafficked Areas! Size Thickness Color 2' x 3 9/16 lack WW K $47.27 lk/yellow WW Y $ ' x 5 9/16 lack WW K $ lk/yellow WW Y $ CARIDE INSERTS DEURRING

124 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID CARIDE END MILLS VARIALE HELIX ENDMILLS HIGH VELOCITY, AlTiN COATED CARIDE 4 Flutes, VHM Series, Corner Radius Variable pitch- Ideal for high production and high speed milling Excellent surface finishes Offset flute design eliminates chatter and reduces machine vibration All tools 3/8 and over have Weldon flats Flute Length Corner Radius The V-Hemoth Master Catalog 1/8 1/8 1-1/2 1/2.010 MI-VHM1254X $ /16 3/16 2 5/8.010 MI-VHM1874X $ /4 1/4 2-1/2 3/4.020 MI-VHM2504X $ /16 5/16 2-1/2 13/ MI-VHM3124X $ /8 3/8 2-1/2 3/4.020 MI-VHM3754X $ /16 7/16 2-1/ MI-VHM4374X $ /2 1/ MI-VHM5004X $ /8 5/8 3-1/2 1-1/4.030 MI-VHM6254X $ /4 3/ /2.030 MI-VHM7504X $ /2.030 MI-VHM0014X $ LONG LENGTH END MILLS Long & Extra Long Length 2 & 4 Flute,Center Cutting, 30 Helix Long Length Flute 2-Flute 4-Flute Length 3/16 3/16 2-1/2 3/4 MI-GLL1872 MI-GLL1874 $ /4 1/ /8 MI-GLL2502 MI-GLL2504 $ /16 5/ /8 MI-GLL3122 MI-GLL3124 $ /8 3/ /8 MI-GLL3752 MI-GLL3754 $ /16 7/16 4-1/2 2 MI-GLL4372 MI-GLL4374 $ /2 1/2 4-1/2 2 MI-GLL5002 MI-GLL5004 $ /8 5/ /4 MI-GLL6252 MI-GLL6254 $ /4 3/ /4 MI-GLL7502 MI-GLL7504 $ /4 MI-GLL0012 MI-GLL0014 $ Extra Long Flute Length 2-Flute 4-Flute 3/16 3/ /8 MI-GEL1872 MI-GEL1874 $ /4 1/ /2 MI-GEL2502 MI-GEL2504 $ /16 5/ /8 MI-GEL3122 MI-GEL3124 $ /8 3/ /4 MI-GEL3752 MI-GEL3754 $ /16 7/ MI-GEL4372 MI-GEL4374 $ /2 1/2 6 3 MI-GEL5002 MI-GEL5004 $ /8 5/8 6 3 MI-GEL6252 MI-GEL6254 $ /4 3/4 6 3 MI-GEL7502 MI-GEL7504 $ MI-GEL0012 MI-GEL0014 $ FEATURES: alanced to 15,000 g6.3 Manufactured to the highest degree of technical excellence to ISO9002 quality control standards Certification included with each holder Crafted from SAE 8620 alloy steel AT3 Class Accuracy alanced holders result in less vibration, chatter and extended tool life. 100% Satisfaction Guaranteed! VARIALE HELIX ENDMILLS LONG LENGTH, HIGH VELOCITY, AlTiN COATED CARIDE 4 Flutes, VHM Series, Corner Radius Variable pitch- Ideal for high production and high speed milling Excellent surface finishes Offset flute design eliminates chatter and reduces machine vibration All tools 3/8 and over have Weldon flats 5 FLUTE END MILLS Center Cutting - 45 Helix ASM-5 Series, Stub Length Ideal For Finishing, Roughing And Slotting In Medium To Hard Steels, Stainless And Hi-Temp Alloys! 5-Flute Stub Length Cutter Flute Length 3/16 3/16 1-1/2 3/8 MI-ASM1875 $ /4 1/4 2 1/2 MI-ASM2505 $ /16 5/16 2 1/2 MI-ASM3125 $ /8 3/8 2 5/8 MI-ASM3755 $ /2 1/2 2-1/2 5/8 MI-ASM5005 $ FLUTE END MILLS Center Cutting - 45 Helix ALM Series, Long Length Ideal For Finishing, Roughing And Slotting In Medium To Hard Steels, Stainless And Hi-Temp Alloys! 5-Flute Long Length Cutter Flute Length Corner Radius Flute Len. The V-Hemoth 1/4 1/ /4 MI-ALM2505 $ /16 5/ /4 MI-ALM3125 $ /8 3/ /2 MI-ALM3755 $ /2 1/2 4 2 MI-ALM5005 $ /8 5/8 6 3 MI-ALM6255 $ /4 3/4 6 3 MI-ALM7505 $ MI-ALM0015 $ /16 3/16 2-1/2 3/4.010 MI-VLM1874X $ /4 1/ /8.020 MI-VLM2504X $ /16 5/ /8.020 MI-VLM3124X $ /8 3/ /4.020 MI-VLM3754X $ /16 7/16 4-1/ MI-VLM4374X $ /2 1/2 4-1/2 2-1/4.030 MI-VLM5004X $ /8 5/ /4.030 MI-VLM6254X $ /4 3/ /2.030 MI-VLM7504X $ /2.030 MI-VLM0014X $ ALANCED TOOLHOLDERS FOR INCREASED SPEED & SPINDLE LIFE! Please See Pages For Our Complete Selection! alanced Toolholders Starting At Only $58.85 each

125 CORNER RADIUS ENDMILLS-SOLID CARIDE CORNER RADIUS ENDMILLS SOLID CARIDE 2 & 4 FLUTE, SINGLE END 30 helix, right hand spiral, right hand cut Center cutting Used for generating corner radius on work piece Corner radius promotes additional strength for longer tool life, resulting in greater productivity Use coated tools for increased tool life Tolerances: Cutting : /-.002 : / Materials: Cast iron, non-ferrous metals plastics and abrasive materials Additional Radii & Coatings Available! Please Call For More Information! 2 FLUTE RADIUS ENDMILLS Uncoated TiAlN Coated Mill LOC Corner Radius 1/8 1/2 1/8 1-1/2.010R MO-EM $8.04 MO-EM $ /8 1/2 1/8 1-1/2.030R MO-EM $8.04 MO-EM $ /16 5/8 3/ R MO-EM $12.69 MO-EM $ /16 5/8 3/ R MO-EM $12.69 MO-EM $ /4 3/4 1/4 2-1/2.015R MO-EM $16.62 MO-EM $ /4 3/4 1/4 2-1/2.030R MO-EM $16.62 MO-EM $ /4 3/4 1/4 2-1/2.060R MO-EM $16.62 MO-EM $ /16 13/16 5/16 2-1/2.015R MO-EM $19.40 MO-EM $ /16 13/16 5/16 2-1/2.030R MO-EM $19.40 MO-EM $ /16 13/16 5/16 2-1/2.060R MO-EM $19.40 MO-EM $ /8 1 3/8 2-1/2.015R MO-EM $23.84 MO-EM $ /8 1 3/8 2-1/2.030R MO-EM $23.84 MO-EM $ /8 1 3/8 2-1/2.060R MO-EM $23.84 MO-EM $ /16 1 7/16 2-3/4.015R MO-EM $32.79 MO-EM $ /16 1 7/16 2-3/4.030R MO-EM $32.79 MO-EM $ /16 1 7/16 2-3/4.060R MO-EM $32.79 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /8 1-1/4 5/8 3-1/2.015R MO-EM $69.91 MO-EM $ /8 1-1/4 5/8 3-1/2.030R MO-EM $69.91 MO-EM $ /8 1-1/4 5/8 3-1/2.060R MO-EM $69.91 MO-EM $ /4 1-1/2 3/ R MO-EM $ MO-EM $ /4 1-1/2 3/ R MO-EM $ MO-EM $ /4 1-1/2 3/ R MO-EM $ MO-EM $ / R MO-EM $ MO-EM $ / R MO-EM $ MO-EM $ / R MO-EM $ MO-EM $ FLUTE RADIUS ENDMILLS Uncoated TiAlN Coated Mill LOC Corner Radius 1/8 1/2 1/8 1-1/2.015R MO-EM $8.04 MO-EM $ /8 1/2 1/8 1-1/2.030R MO-EM $8.04 MO-EM $ /16 5/8 3/ R MO-EM $12.69 MO-EM $ /16 5/8 3/ R MO-EM $12.69 MO-EM $ /4 3/4 1/4 2-1/2.020R MO-EM $16.62 MO-EM $ /4 3/4 1/4 2-1/2.030R MO-EM $16.62 MO-EM $ /16 13/16 5/16 2-1/2.020R MO-EM $19.40 MO-EM $ /16 13/16 5/16 2-1/2.030R MO-EM $19.40 MO-EM $ /8 1 3/8 2-1/2.015R MO-EM $23.84 MO-EM $ /8 1 3/8 2-1/2.030R MO-EM $23.84 MO-EM $ /8 1 3/8 2-1/2.060R MO-EM $23.84 MO-EM $ /16 1 7/16 2-3/4.015R MO-EM $32.79 MO-EM $ /16 1 7/16 2-3/4.030R MO-EM $32.79 MO-EM $ /16 1 7/16 2-3/4.060R MO-EM $32.79 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /2 1 1/ R MO-EM $41.10 MO-EM $ /8 1-1/4 5/8 3-1/2.015R MO-EM $69.91 MO-EM $ /8 1-1/4 5/8 3-1/2.030R MO-EM $69.91 MO-EM $ /8 1-1/4 5/8 3-1/2.060R MO-EM $69.91 MO-EM $ /8 1-1/4 5/8 3-1/2.125R MO-EM $69.91 MO-EM $ /4 1-1/2 3/ R MO-EM $ MO-EM $ /4 1-1/2 3/ R MO-EM $ MO-EM $ /4 1-1/2 3/ R MO-EM $ MO-EM $ /4 1-1/2 3/ R MO-EM $ MO-EM $ / R MO-EM $ MO-EM $ / R MO-EM $ MO-EM $ / R MO-EM $ MO-EM $ / R MO-EM $ MO-EM $ Master Catalog 393 C CARIDE INSERTS DEURRING

126 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ROUGHER/FINISHER ENDMILLS-SOLID CARIDE ROUGHING/FINISHING ENDMILLS WITH CHIPREAKER SQUARE AND ALL END 3 & 4 FLUTES, CARIDE Manufactured from the highest quality carbide material with 10% cobalt Sinter hipped, C-2 grade, fine grain carbide Chipbreaker geometry permits extremely high feed rates in roughing operations Designed with tooth overlap to produce fairly smooth part finish Minimizes cutting force for longer tool life SQUARE END Mill. 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1 ALL NOSE Mill. 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1 LOC Coating 3 Flute Master Catalog 4 Flute 1/2 1/8 1-1/2 Uncoated MO MO $9.38 1/2 1/8 1-1/2 TiAlN MO MO $ /8 3/16 2 Uncoated MO MO $ /8 3/16 2 TiAlN MO MO $ /4 1/4 2-1/2 Uncoated MO MO $ /4 1/4 2-1/2 TiAlN MO MO $ /16 5/16 2-1/2 Uncoated MO MO $ /16 5/16 2-1/2 TiAlN MO MO $ /8 2-1/2 Uncoated MO MO $ /8 2-1/2 TiAlN MO MO $ /16 2-3/4 Uncoated MO MO $ /16 2-3/4 TiAlN MO MO $ /2 3 Uncoated MO MO $ /2 3 TiAlN MO MO $ /4 5/8 3-1/2 Uncoated MO MO $ /4 5/8 3-1/2 TiAlN MO MO $ /2 3/4 4 Uncoated MO MO $ /2 3/4 4 TiAlN MO MO $ /2 1 4 Uncoated MO MO $ /2 1 4 TiAlN MO MO $ LOC Coating 3 Flute 4 Flute 1/2 1/8 1-1/2 Uncoated MO MO $ /2 1/8 1-1/2 TiAlN MO MO $ /8 3/16 2 Uncoated MO MO $ /8 3/16 2 TiAlN MO MO $ /4 1/4 2-1/2 Uncoated MO MO $ /4 1/4 2-1/2 TiAlN MO MO $ /16 5/16 2-1/2 Uncoated MO MO $ /16 5/16 2-1/2 TiAlN MO MO $ /8 2-1/2 Uncoated MO MO $ /8 2-1/2 TiAlN MO MO $ /16 2-3/4 Uncoated MO MO $ /16 2-3/4 TiAlN MO MO $ /2 3 Uncoated MO MO $ /2 3 TiAlN MO MO $ /4 5/8 3-1/2 Uncoated MO MO $ /4 5/8 3-1/2 TiAlN MO MO $ /2 3/4 4 Uncoated MO MO $ /2 3/4 4 TiAlN MO MO $ /2 1 4 Uncoated MO MO $ /2 1 4 TiAlN MO MO $ C

127 ENDMILLS-ROUGHING 3 FLUTE ROUGHING ENDMILLS FINE PITCH & SPECIAL GEOMETRY Cobalt, Carbide & Stellar One For Aluminum 3 Flute Coarse & Fine Pitch & Special Geometry ROUGHERS Mill Material LOC Cut Application Helix Angle Coating Type Flats Vendor 3/16 CO 1/2 3/8 2-3/8 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP1206 $ /4 5/16 3/8 1/2 5/8 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 3/4 1/4 2-1/2 CC Fine Pitch - For Aluminum - A SE - YG1 X-Power YG-EM93112 $27.24 C CAR 3/4 1/4 2-1/2 CC Fine Pitch - For Aluminum - A SE - YG1 Jet Power YG-EM95079 $25.72 C CO 5/8 3/8 2-7/16 CC Fine Pitch - For Aluminum - L SE - YG1 YG-EM76297CF $27.22 C CO 5/8 3/8 2-7/16 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-1208 $20.68 CO 5/8 3/8 2-7/16 NC Fine Pitch - For Steels - C SE - YG1 YG-EM70297CC $24.72 C CO 5/8 3/8 2-7/16 NC Coarse Pitch - For Aluminum - U SE - YG1 YG-EM60297 $15.57 C CO 5/8 3/8 2-7/16 NC Fine Pitch - For Steels - U SE - YG1 YG-EM70297 $17.14 C CO 1-1/8 3/8 2-15/16 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-1208-L $22.42 CO 5/8 3/8 2-7/16 NC Coarse Tooth-General Purpose - U SE Yes TMX I $18.05 C CAR 3/4 5/16 2-1/2 CC Fine Pitch - For Aluminum - A SE - YG1 X-Power YG-EM93113 $38.00 C CAR 3/4 5/16 2-1/2 CC Fine Pitch - For Aluminum - A SE - YG1 Jet Power YG-EM95080 $34.57 C CO 3/4 3/8 2-1/2 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-1210 $21.76 CO 3/4 3/8 2-1/2 NC Coarse Pitch - For Aluminum - U SE - YG1 YG-EM60301 $15.57 C CO 3/4 3/8 2-1/2 NC Coarse Tooth-General Purpose - U SE Yes TMX I $21.73 C CAR 7/8 3/8 2-1/2 CC Fine Pitch - For Aluminum - A SE - YG1 X-Power YG-EM93114 $44.94 C CO 3/4 3/8 2-1/2 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN $32.72 C CO 3/4 3/8 2-1/2 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-1208 $42.53 C CO 3/4 3/8 2-1/2 CC Coarse Pitch - For Aluminum - U SE - YG1 YG-EM66305 $21.82 C CO 1-3/8 3/8 3-1/8 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $42.68 C CO 1-3/8 3/8 3-1/8 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-1213 $55.49 C CO 1-1/2 3/8 3-1/4 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-1212-L $25.81 CO 1/2 1/2 2-9/16 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERPS $25.01 CO 1-1/4 1/2 3-1/4 CC Sp. Geom Rough-Polished Flts-Alum - C SE Yes MINICUT MNTC930PM-1612 $52.94 C CO 1-1/4 1/2 3-1/4 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $33.70 C CO 1-1/4 1/2 3-1/4 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-1612 $43.83 C CO 1-1/4 1/2 3-1/4 CC Sp. Geom Rough-Polished Flts-Alum - U SE Yes MINICUT MN930PM-1612 $50.77 C CO 1-1/4 1/2 3-1/4 CC Coarse Pitch - For Aluminum - U SE - YG1 YG-EM66321 $29.97 C CO 1-5/8 1/2 3-5/8 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-1616-M $30.03 CO 2 1/2 4 CC Sp. Geom Rough-Polished Flts-Alum - C SE Yes MINICUT PM MNTC930PM-1620 $71.74 C CO 2 1/2 4 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $43.95 C CO 2 1/2 4 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-1620 $57.14 C CO 3 1/2 5 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $55.91 C STE 1-1/4 1/2 3-1/4 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $32.59 C STE 2 1/2 4 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $43.02 C CO 3/4 5/8 2-7/8 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERPS-2020 $27.84 CO 1-5/8 5/8 3-3/4 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $47.36 C CO 1-5/8 5/8 3-3/4 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-2016 $61.58 C CO 2-1/2 5/8 4-5/8 CC Sp. Geom Rough-Polished Flts-Alum - C SE Yes MINICUT MNTC930PM-2025 $ C CO 2-1/2 5/8 4-5/8 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $58.75 C CO 2-1/2 5/8 4-5/8 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-2025 $76.37 C STE 1-5/8 5/8 3-3/4 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $40.89 C STE 2-1/2 5/8 4-5/8 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $46.97 C 3/4 & Larger Sizes Continued On Following Page International Minicut Item Description Cobalt M-42 - Roughing Endmill To Machine Aluminium Pm Super Cobalt For High Velocity Machining Of Aluminium Minicut Stellar One - List 985 To Machine Inconel, Stainless & High Tensile Steels List 995 To Machine Titanium Alloys List 811 & Roughing Endmills Coarse Pitch 811 & Fine Pitch 816 Combination Endmills High Helix For Aluminium International Standard Endmills High Helix For Aluminium Cobalt M-42 - Finishing Endmill To Machine Titanium Alloy Master Catalog 395 Code For additional information on International Minicut, please visit CARIDE INSERTS DEURRING

128 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-ROUGHING 3 FLUTE ROUGHING ENDMILLS (continued) FINE PITCH & SPECIAL GEOMETRY Cobalt, Carbide & Stellar One For Aluminum 3 Flute Coarse & Fine Pitch & Special Geometry ROUGHERS (continued) Mill 3/ /4 List 930 List 930P Material LOC Cut Application Helix Angle Coating Type Flats Vendor Master Catalog ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CO 3/4 3/4 3 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERPS-2424 $38.27 CO 1-5/8 3/4 3-3/4 CC Coarse Pitch - For Aluminum - U SE - YG1 YG-EM66359 $46.07 C CO 1-5/8 3/4 3-7/8 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $53.49 C CO 1-5/8 3/4 3-7/8 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-2416 $69.52 C CO 2 3/4 4-1/4 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP $43.16 CO 2-1/4 3/4 4-1/2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $62.23 C CO 2-1/4 3/4 4-1/2 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-2422 $80.89 C CO 3 3/4 5-1/4 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-2424-L $52.68 CO 3 3/4 5-1/4 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $70.99 C CO 3 3/4 5-1/4 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-2430 $92.28 C CO 4 3/4 6-1/4 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $84.65 C CO 4 3/4 6-1/4 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-2440 $ C STE 2-1/4 3/4 4-1/2 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $54.90 C STE 3 3/4 5-1/4 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $59.17 C STE 4 3/4 6-1/4 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $87.54 C CO 1-1/8 3/4 3-3/8 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERPS-2432 $53.29 CO 1-1/2 3/4 3-3/4 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-2432 $60.18 CO /2 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-3232 $63.46 CO /2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $82.22 C CO /2 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-3220 $ C CO /2 CC Sp. Geom Rough-Polished Flts-Alum - U SE Yes MINICUT PM MN930PM-3220 $ C CO /2 CC Coarse Pitch - For Aluminum - U SE - YG1 YG-EM66426 $69.39 C CO /2 CC Coarse Pitch - For Aluminum - U SE Yes MELIN ME-ERP-3232-M $66.66 CO /2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $ C CO /2 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-3230 $ C CO /2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $ C CO /2 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-3240 $ C CO /2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $ C STE 2-1/ /4 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $84.79 C STE /2 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $86.87 C STE /2 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $90.98 C CO 2 1-1/4 4-1/2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $ C CO 2 1-1/4 4-1/2 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-4020 $ C CO 3 1-1/4 5-1/2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $ C CO 3 1-1/4 5-1/2 CC Sp. Geom Rough-Polished Flts-Alum 43.5 U SE Yes MINICUT MN930P-4030 $ C CO 4 1-1/4 6-1/2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $ C CO 6 1-1/4 8-1/2 CC Special Geom Rough. - For Alum 43.5 U SE Yes MINICUT MN $ C STE 2-1/4 1-1/4 4-3/4 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $99.95 C STE 4 1-1/4 6-1/2 CC Fine Pitch - For Aluminum - U SE - MINICUT MN $ C 1-1/2 CO 2 1-1/4 4-1/2 CC Sp. Geom Rough-Polished Flts-Alum - U SE Yes MINICUT MN930P-4820 $ C ALANCED TOOLHOLDERS FOR INCREASED SPEED & SPINDLE LIFE! Kingston Tool offers a complete line of balanced CNC tool holders, manufactured to meet today s machinists need for speed and accuracy at a competitive price. alanced to 15,000 g6.3, Kingston alanced Toolholders increase spindle and tool life, as well as helping to improve surface finish. alanced Toolholders Starting At Only $58.85 each Please See Pages For Our Complete Selection! Code FEATURES: alanced to 15,000 g6.3 Manufactured to the highest degree of technical excellence to ISO9002 quality control standards Certification included with each holder Crafted from SAE 8620 alloy steel AT3 Class Accuracy alanced holders result in less vibration, chatter and extended tool life. 100% Satisfaction Guaranteed!

129 ENDMILLS-ROUGHING 4 FLUTE ROUGHING ENDMILLS COARSE & FINE PITCH Cobalt, Carbide & Stellar One For Steels 4 Flute Coarse & Fine Pitch ROUGHERS Mill Material LOC Cut Application Coating Type Flats Vendor 3/16 CO 1/2 3/8 2-3/8 NC Fine Pitch U SE No MELIN ME-CFP-1206 $ /4 5/16 3/8 7/16 1/2 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CO 5/8 3/8 2-7/16 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1208 $21.97 CO 5/8 3/8 2-7/16 CC Fine Pitch U SE No MELIN ME-CCFP-1208 $21.97 CO 5/8 3/8 2-7/16 NC Fine Pitch U SE No MELIN ME-CFP-1208 $20.68 CO 1-1/8 3/8 2-15/16 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1208-L $23.83 CO 1-1/8 3/8 2-15/16 CC Fine Pitch U SE No MELIN ME-CCFP-1208-L $23.83 CO 3/4 3/8 2-1/2 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1210 $23.12 CO 3/4 3/8 2-1/2 CC Fine Pitch U SE No MELIN ME-CCFP-1210 $23.12 CO 3/4 3/8 2-1/2 NC Fine Pitch U SE No MELIN ME-CFP-1210 $21.76 CO 1-3/8 3/8 3-1/8 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1210-L $28.53 CO 1-3/8 3/8 3-1/8 CC Fine Pitch U SE No MELIN ME-CCFP-1210-L $28.53 CO 3/8 3/8 2-1/8 CC Fine Pitch U SE No MELIN ME-CCFPS-1212 $26.18 CO 3/8 3/8 2-5/32 CC Fine Pitch - For Steels C SE - YG1 YG-EM75305CC $29.27 C CO 3/4 3/8 2-1/2 CC Coarse Pitch - For Steels C SE - YG1 YG-EM76305CC $27.22 C CO 3/4 3/8 2-1/2 CC Fine Pitch - For Steels L SE - YG1 YG-EM76305CF $27.22 C CO 3/4 3/8 2-1/2 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1212 $23.89 CO 3/4 3/8 2-1/2 CC Fine Pitch U SE No MELIN ME-CCFP-1212 $23.89 CO 3/4 3/8 2-1/2 CC Fine Pitch - For Steels U SE - YG1 YG-EM76305 $18.52 C CO 3/4 3/8 2-1/2 NC Coarse Pitch - For Steels C SE - YG1 YG-EM60305CC $23.17 C CO 3/4 3/8 2-1/2 NC Fine Pitch - For Steels C SE - YG1 YG-EM70305CC $24.72 C CO 3/4 3/8 2-1/2 NC Coarse Pitch - For Steels L SE - YG1 YG-EM60305CF $23.17 C CO 3/4 3/8 2-1/2 NC Coarse Pitch - For Steels U SE - YG1 YG-EM60305 $15.57 C CO 1-1/2 3/8 3-1/4 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1212-L $27.44 CO 1-1/2 3/8 3-1/4 CC Fine Pitch U SE No MELIN ME-CCFP-1212-L $27.44 STE 3/4 3/8 2-1/2 CC Fine Pitch U SE - MINICUT MN $28.20 C CO 3/4 3/8 2-1/2 CC Coarse Tooth-General Purpose U SE - TMX I $18.05 C CO 1 3/8 2-11/16 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1214 $27.44 CO 1 3/8 2-11/16 NC Coarse Tooth-General Purpose U SE Yes TMX I $21.73 C CO 1 3/8 2-11/16 CC Fine Pitch U SE No MELIN ME-CCFP-1214 $27.44 CO 1 3/8 2-11/16 NC Coarse Pitch - For Steels U SE - YG1 YG-EM60312 $21.70 C CAR 5/8 1/2 3 CC Fine Pitch U SE - YG1 X-Power YG-EM93273 $49.74 C CAR 1 1/2 3 CC Fine Pitch U SE - YG1 X-Power YG-EM93115 $71.64 C CO 1/2 1/2 2-1/2 CC Fine Pitch - For Steels C SE - YG1 YG-EM75321CC $39.05 C CO 1/2 1/2 2-1/2 CC Fine Pitch - For Steels L SE - YG1 YG-EM75321CF $39.05 C CO 1/2 1/2 2-1/2 CC Fine Pitch U SE No MELIN ME-CCFPS-1616 $26.99 CO 5/8 1/2 2-5/8 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP $26.99 CO 5/8 1/2 2-5/8 CC Fine Pitch U SE No MELIN ME-CCFP $26.99 CO 5/8 1/2 2-5/8 NC Fine Pitch U SE No MELIN ME-CFPS $25.01 CO 1 1/2 3 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRPS-1616 $26.99 CO 1 1/2 3 NC Fine Pitch U SE No MELIN ME-CFPS-1616 $25.64 CO 1-1/4 1/2 3-1/4 CC Fine Pitch - For Steels C SE - YG1 YG-EM76321CC $39.47 C CO 1-1/4 1/2 3-1/4 CC Fine Pitch - For Steels L SE - YG1 YG-EM76321CF $39.47 C CO 1-1/4 1/2 3-1/4 NC Coarse Tooth-General Purpose U SE Yes TMX I $20.60 C CO 1-1/4 1/2 3-1/4 CC Fine Pitch U SE No MELIN ME-CCFP-1616 $28.92 CO 1-1/4 1/2 3-1/4 CC Coarse Pitch - For Steels U SE - YG1 YG-EM64321 $23.54 C CO 1-1/4 1/2 3-1/4 CC GP For Steels U SE - YG1 YG-EM73321 $23.54 C CO 1-1/4 1/2 3-1/4 CC Fine Pitch - For Steels U SE - YG1 YG-EM76321 $25.45 C CO 1-1/4 1/2 3-1/4 NC Coarse Pitch - For Steels C SE - YG1 YG-EM60321CC $33.72 C CO 1-1/4 1/2 3-1/4 NC Fine Pitch - For Steels C SE - YG1 YG-EM70321CC $35.57 C CO 1-1/4 1/2 3-1/4 NC Coarse Pitch - For Steels I SE - YG1 YG-EM60321CN $30.35 C CO 1-1/4 1/2 3-1/4 NC Coarse Pitch - For Steels L SE - YG1 YG-EM60321CF $33.72 C CO 1-1/4 1/2 3-1/4 NC Fine Pitch - For Steels L SE - YG1 YG-EM70321CF $35.57 C CO 1-1/4 1/2 3-1/4 NC Coarse Pitch - For Steels U SE Yes MELIN ME-CRP-1616 $28.92 CO 1-1/4 1/2 3-1/4 NC Coarse Pitch - For Steels U SE - YG1 YG-EM60321 $21.70 C CO 1-1/4 1/2 3-1/4 NC Fine Pitch - For Steels U SE - YG1 YG-EM70321 $23.54 C 1/2 & Larger Sizes Continued On Following Page Master Catalog 397 Code CARIDE INSERTS DEURRING

130 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-ROUGHING 4 FLUTE ROUGHING ENDMILLS (continued) COARSE & FINE PITCH Cobalt, Carbide & Stellar One For Steels 4 Flute Coarse & Fine Pitch ROUGHERS (continued) Mill 1/2 9/16 5/8 3/4 Material LOC Cut Application Coating Type Flats Vendor Master Catalog ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CO 1-5/8 1/2 3-5/8 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1616-M $31.62 CO 1-5/8 1/2 3-5/8 CC Fine Pitch U SE No MELIN ME-CCFP-1616-M $31.62 CO 2 1/2 4 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-1616-L $40.29 CO 2 1/2 4 CC Fine Pitch U SE No MELIN ME-CCFP-1616-L $40.29 CO 2 1/2 4 NC Coarse Tooth-Gen Purp U SE Yes TMX I $29.00 C STE 3 1/2 5 CC Fine Pitch U SE - MINICUT MN $61.41 C CO 1-3/8 1/2 3-3/8 NC Coarse Tooth-Gen Purp U SE Yes TMX I $27.78 C CO 1-3/8 1/2 3-3/8 NC Fine Pitch U SE No MELIN ME-CFP-1618 $30.03 CO 5/8 5/8 2-3/4 CC Fine Pitch U SE No MELIN ME-CCFPS-2020 $29.30 CO 1-1/4 5/8 3-3/4 NC Fine Pitch U SE No MELIN ME-CFP $29.31 CO 1-5/8 5/8 3-3/4 CC Fine Pitch - For Steels L SE - YG1 YG-EM76337CF $47.17 C CO 1-5/8 5/8 3-3/4 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-2020 $35.80 CO 1-5/8 5/8 3-3/4 CC Fine Pitch U SE No MELIN ME-CCFP-2020 $35.80 CO 1-5/8 5/8 3-3/4 NC Fine Pitch - For Steels C SE - YG1 YG-EM70337CC $42.65 C CO 1-5/8 5/8 3-3/4 NC Fine Pitch U SE No MELIN ME-CFP-2020 $34.00 CO 1-5/8 5/8 3-3/4 NC Coarse Pitch - For Steels U SE - YG1 YG-EM60337 $26.47 C CO 2-1/2 5/8 4-5/8 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-2020-L $47.87 CO 2-1/2 5/8 4-5/8 CC Fine Pitch U SE No MELIN ME-CCFP-2020-L $47.87 CO 1-5/8 5/8 3-3/4 NC Coarse Tooth-GP U SE Yes TMX I $31.80 C CO 2-1/2 5/8 4-5/8 NC Coarse Tooth-GP U SE Yes TMX I $41.95 C CAR 1-5/8 3/4 4 CC Fine Pitch U SE - YG1 YG-EM93117 $ C CO 3/4 3/4 2-7/8 CC Fine Pitch - For Steels C SE - YG1 YG-EM75359CC $58.45 C CO 3/4 3/4 3 CC Fine Pitch U SE No MELIN ME-CCFPS-2424 $48.78 CO 3/4 3/4 3 NC Fine Pitch U SE No MELIN ME-CFPS-2424 $38.27 CO 1-1/4 3/4 3-1/2 NC Fine Pitch U SE No MELIN ME-CFP $39.06 CO 1-5/8 3/4 3-3/4 NC Coarse Pitch - For Steels C SE - YG1 YG-EM60359CC $48.82 C CO 1-5/8 3/4 3-3/4 NC Coarse Pitch - For Steels L SE - YG1 YG-EM60359CF $48.82 C CO 1-5/8 3/4 3-3/4 NC Coarse Pitch - For Steels U SE - YG1 YG-EM60359 $32.90 C CO 1-5/8 3/4 3-7/8 CC Fine Pitch - For Steels C SE - YG1 YG-EM76359CC $57.64 C CO 1-5/8 3/4 3-7/8 CC Fine Pitch - For Steels L SE - YG1 YG-EM76359CF $57.64 C CO 1-5/8 3/4 3-7/8 CC Fine Pitch U SE No MELIN ME-CCFP-2424 $43.63 CO 1-5/8 3/4 3-7/8 NC Fine Pitch - For Steels C SE - YG1 YG-EM70359CC $52.12 C CO 1-5/8 3/4 3-7/8 NC Fine Pitch - For Steels L SE - YG1 YG-EM70359CF $52.12 C CO 1-5/8 3/4 3-7/8 NC Fine Pitch U SE No MELIN ME-CFP-2424 $41.45 CO 1-5/8 3/4 3-7/8 NC Coarse Pitch - For Steels U SE Yes MELIN ME-CRP-2424 $43.63 CO 1-5/8 3/4 3-3/4 NC Coarse Tooth-GP U SE Yes TMX I $52.60 C CO 2-1/4 3/4 4-5/8 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-2424-M $47.22 CO 2-1/4 3/4 4-5/8 CC Fine Pitch U SE No MELIN ME-CCFP-2424-M $47.22 CO 2-1/2 3/4 4-5/8 NC Coarse Pitch - For Steels U SE No MELIN ME-CFP-2424-M $44.85 CO 3 3/4 5-1/4 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-2424-L $55.45 CO 3 3/4 5-1/4 CC Fine Pitch U SE No MELIN ME-CCFP-2424-L $55.45 CO 3 3/4 5-1/4 NC Coarse Pitch - For Steels U SE Yes MELIN ME-CRP-2424-L $55.45 CO 3 3/4 5-1/4 NC Coarse Pitch - For Steels U SE - YG1 YG-EM62359 $41.14 C CO 3 3/4 5-1/4 NC Coarse Tooth-GP U SE Yes TMX I $49.90 C STE 3 3/4 5-1/4 CC Coarse Pitch - For Steels U SE - MINICUT MN $72.63 C STE 4 3/4 6-1/4 CC Fine Pitch U SE - MINICUT MN $87.15 C VENTURE II SAFETY GLASSES 9.75 base curved lens provides full side protection without distracting seams or traditional type side shields Nose buds secure the glass and prevent slipping while providing a pillow soft fit Temples adjust to four different lengths Lenses are coated for superior scratch resistance Lenses provide 99% protection against harmful UV rays Exceeds ANSI Z standards CE EN166 and CAN/CSA Z certified Frame Color lack Lens Color Code Clear PYR-S1810S $4.39 Gray PYR-S1820S $4.99 lue PYR-S1860S $4.99 Amber PYR-S1830S $4.99

131 ENDMILLS-ROUGHING 5 & 6 FLUTE ROUGHING ENDMILLS COARSE & FINE PITCH Cobalt & Carbide For Steels 5 & 6 Flute Coarse & Fine Pitch ROUGHERS Mill 5 FLUTE Material LOC Cut Application Coating Type Flats Vendor 1/2 CAR 1-1/4 1/2 3 CC Fine Pitch L SE - YG1 YG-EM82593TF $80.10 C 1 CO 3/4 3/4 3 NC Coarse Pitch - For Steels U SE Yes MELIN ME-CRPS-2432 $53.53 CO 1-1/8 3/4 3-3/8 NC Fine Pitch U SE No MELIN ME-CFPS-2432 $53.29 CO /2 CC Fine Pitch - For Steels L SE - YG1 YG-EM76426CF $87.94 C CO /2 NC Coarse Tooth-GP U SE Yes TMX I $69.00 C CO /2 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-3232 $62.32 CO /2 NC Fine Pitch - For Steels C SE - YG1 YG-EM70426CC $79.22 C CO /2 NC Fine Pitch - For Steels L SE - YG1 YG-EM70426CF $79.22 C CO /2 NC Coarse Pitch - For Steels U SE - YG1 YG-EM60426 $47.60 C CO /2 NC Coarse Pitch - For Steels U SE - YG1 YG-EM61426 $58.79 C CO /2 NC Coarse Tooth-GP U SE Yes TMX I $ C CO /2 NC Coarse Pitch - For Steels U SE - YG1 YG-EM62426 $68.32 C 6 FLUTE 3/8 CAR 7/8 3/8 2-7/8 CC Fine Pitch U SE - YG1 X-Power YG-EM93121 $58.27 C 1/2 CAR 1 1/2 3-1/4 CC Fine Pitch U SE - YG1 X-Power YG-EM93122 $79.19 C 1-1/4 1-1/2 CO 2 1-1/4 4-1/2 CC Coarse Pitch - For Steels U SE Yes MELIN ME-CCRP-4040 $81.47 CO 2 1-1/4 4-1/2 NC Coarse Tooth-GP U SE Yes TMX I $ C CO 4 1-1/4 6-1/2 NC Coarse Tooth-GP U SE Yes TMX I $ C CO 2 1-1/4 4-1/2 NC Coarse Tooth-GP U SE Yes TMX I $ C CO 4 1-1/4 6-1/2 NC Coarse Tooth-GP U SE Yes TMX I $ C 4 FLUTE ROUGHING ENDMILLS SOLID CARIDE-FINE PITCH. Center cutting geometry For carbon, alloy and hard steel, stainless steels and nickel/inconel alloy Designed for increased chip removal rate Capable of slotting, profiling, and plunging operations Premium sub micro grain Carbide Form relieved Small corner radius for strength ROUGHING ENDMILLS SOLID CARIDE 4 Flutes, SHR Series AlTiN Coated, 38 helix Designed to generate the maximum metal removal rates in most applications All tools 3/8 and over have Weldon flats. Flute Length The Shredder 1/4 1/4 2-1/2 3/4 MI-SHR2504X $ /16 5/16 2-1/2 13/16 MI-SHR3124X $ /8 3/8 2-1/2 7/8 MI-SHR3754X $ /2 1/2 3 1 MI-SHR5004X $ /8 5/8 3-1/2 1-1/4 MI-SHR6254X $ /4 3/ /4 MI-SHR7504X $ /4 MI-SHR0014X $ LOC. NEW ITEM!. Uncoated Flute Length ROUGHING ENDMILLS FOR ALUMINUM SOLID CARIDE 3 Flutes, SAR Series 3 flute design, 38 helix Designed to generate the maximum metal removal rates in most applications Designed specifically for aluminum All tools 3/8 and over have Weldon flats TiAlN Coated 1/4 1/4 2-1/2 3/4 MI-SAR2503 $ /16 5/16 2-1/2 13/16 MI-SAR3123 $ /8 3/8 2-1/2 7/8 MI-SAR3753 $ /2 1/2 3 1 MI-SAR5003 $ /8 5/8 3-1/2 1-1/4 MI-SAR6253 $ /4 3/ /4 MI-SAR7503 $ /4 MI-SAR0013 $ Master Catalog 399 Code 1/4" 1/4" 3/4" 2-1/2" I $26.37 I $ /16" 5/16" 11/32" 2-1/2" I $31.38 I $ /8" 3/8" 7/8" 2-1/2" I $37.03 I $ /16" 7/16" 1" 2-3/4" I $48.96 I $ /2" 1/2" 1-1/4" 3" I $58.38 I $ /16" 9/16" 1-1/4" 3-1/2" I $62.77 I $ /8" 5/8" 1-1/4" 3-1/2" I $97.29 I $ /4" 3/4" 1-1/2" 4" I $ I $ " 1" 1-1/2" 4" I $ I $ The Shredder CARIDE INSERTS DEURRING

132 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID CARIDE ALL ENDMILLS SOLID CARIDE ENDMILLS 2 FLUTE, ALL END Premium sub-micron C-2 carbide with 10% cobalt all end allows for three axis contour slotting and contour finishing Available uncoated, Tin coated and TiAlN coated Tolerances: Cutting : +.000/-.002 : / Applications: Slotting and pocketing Materials: Uncoated: General purpose milling of all materials TiN Coated (gold): Increased tool life in milling of all ferrous materials TiAlN Coated (dark gray): Increased tool life in milling of steels, alloy steels and hardened steels Full Line Available! Please call for more information.. SOLID CARIDE ENDMILLS 4 FLUTE, ALL END Premium sub-micron C-2 carbide with 10% cobalt all end allows for three axis contour slotting and contour finishing Available uncoated, Tin coated and TiAlN coated Tolerances: Cutting : +.000/-.002 : / LOC Master Catalog Uncoated TiN Coated TiAlN Coated 1/64 3/64 1/8 1-1/2 MO-EM $ /32 1/8 1/8 1-1/2 MO-EM $9.51 MO-EM $10.59 MO-EM $ /64 1/8 1/8 1-1/2 MO-EM $9.16 MO-EM $10.24 MO-EM $ /16 1/4 1/8 1-1/2 MO-EM001008AA-2 $7.75 MO-EM $8.83 MO-EM $9.79 5/64 1/4 1/8 1-1/2 MO-EM $7.75 MO-EM $8.83 MO-EM $9.79 3/32 3/8 1/8 1-1/2 MO-EM $7.75 MO-EM $8.83 MO-EM $9.79 7/64 3/8 1/8 1-1/2 MO-EM $7.75 MO-EM $8.83 MO-EM $9.79 1/8 1/2 1/8 1-1/2 MO-EM $7.46 MO-EM $8.54 MO-EM $9.50 9/64 9/16 3/16 2 MO-EM $10.94 MO-EM $12.50 MO-EM $ /32 9/16 3/16 2 MO-EM $10.94 MO-EM $12.50 MO-EM $ /16 5/8 3/16 2 MO-EM $10.13 MO-EM $11.69 MO-EM $ /32 5/8 1/4 2-1/2 MO-EM $15.27 MO-EM $18.00 MO-EM $ /4 3/4 1/4 2-1/2 MO-EM $14.34 MO-EM $17.08 MO-EM $ /32 3/4 5/16 2-1/2 MO-EM $21.26 MO-EM $24.70 MO-EM $ /16 13/16 5/16 2-1/2 MO-EM $19.53 MO-EM $22.97 MO-EM $ /32 1 3/8 2-1/2 MO-EM $25.81 MO-EM $29.25 MO-EM $ /8 1 3/8 2-1/2 MO-EM $26.27 MO-EM $29.71 MO-EM $ /32 1 7/16 2-3/4 MO-EM $34.55 MO-EM $40.09 MO-EM $ /16 1 7/16 2-3/4 MO-EM $32.79 MO-EM $38.32 MO-EM $ /32 1 1/2 3 MO-EM $41.50 MO-EM $47.03 MO-EM $ /2 1 1/2 3 MO-EM $40.45 MO-EM $45.98 MO-EM $ /16 1-1/4 9/16 3-1/2 MO-EM $58.98 MO-EM $67.60 MO-EM $ /8 1-1/4 5/8 3-1/2 MO-EM $70.13 MO-EM $78.75 MO-EM $ /16 1-1/2 3/4 4 MO-EM $ MO-EM $ MO-EM $ /4 1-1/2 3/4 4 MO-EM $ MO-EM $ MO-EM $ /8 1-1/2 7/8 4 MO-EM $ MO-EM $ MO-EM $ /2 1 4 MO-EM $ MO-EM $ MO-EM $ LOC. American Made Carbide End Mills At High Speed Steel s! Uncoated TiN Coated TiAlN Coated 1/64 3/64 1/8 1-1/2 MO-EM $ /32 1/8 1/8 1-1/2 MO-EM $9.51 MO-EM $10.59 MO-EM $ /64 1/8 1/8 1-1/2 MO-EM $9.16 MO-EM $10.24 MO-EM $ /16 1/4 1/8 1-1/2 MO-EM $7.75 MO-EM $9.79 MO-EM $9.79 5/64 1/4 1/8 1-1/2 MO-EM $7.75 MO-EM $8.83 MO-EM $9.79 3/32 3/8 1/8 1-1/2 MO-EM $7.75 MO-EM $8.83 MO-EM $9.79 7/64 3/8 1/8 1-1/2 MO-EM $7.75 MO-EM $8.83 MO-EM $9.79 1/8 1/2 1/8 1-1/2 MO-EM $7.46 MO-EM $8.54 MO-EM $9.50 9/64 9/16 3/16 2 MO-EM $10.94 MO-EM $12.50 MO-EM $ /32 9/16 3/16 2 MO-EM $10.94 MO-EM $12.50 MO-EM $ /16 5/8 3/16 2 MO-EM $10.13 MO-EM $11.69 MO-EM $ /32 5/8 1/4 2-1/2 MO-EM $15.27 MO-EM $18.00 MO-EM $ /4 3/4 1/4 2-1/2 MO-EM $14.34 MO-EM $17.08 MO-EM $ /32 3/4 5/16 2-1/2 MO-EM $21.26 MO-EM $24.70 MO-EM $ /16 13/16 5/16 2-1/2 MO-EM $19.53 MO-EM $22.97 MO-EM $ /32 1 3/8 2-1/2 MO-EM $25.81 MO-EM $29.25 MO-EM $ /8 1 3/8 2-1/2 MO-EM $26.27 MO-EM $29.71 MO-EM $ /32 1 7/16 2-3/4 MO-EM $34.55 MO-EM $40.09 MO-EM $ /16 1 7/16 2-3/4 MO-EM $32.79 MO-EM $38.32 MO-EM $ /32 1 1/2 3 MO-EM $41.50 MO-EM $47.03 MO-EM $ /2 1 1/2 3 MO-EM $40.45 MO-EM $45.98 MO-EM $ /16 1-1/4 9/16 3-1/2 MO-EM $58.98 MO-EM $67.60 MO-EM $ /8 1-1/4 5/8 3-1/2 MO-EM $70.13 MO-EM $78.75 MO-EM $ /16 1-1/2 3/4 4 MO-EM $ MO-EM $ MO-EM $ /4 1-1/2 3/4 4 MO-EM $ MO-EM $ MO-EM $ /8 1-1/2 7/8 4 MO-EM $ MO-EM $ MO-EM $ /2 1 4 MO-EM $ MO-EM $ MO-EM $ C American Made Carbide End Mills At High Speed Steel s!

133 ENDMILLS-2 FLUTE/ALL END 2 FLUTE ALL END ENDMILLS Cobalt & Carbide For Aluminum, Plastic & Non-Ferrous Materials 2 Flute all End Endmills (HSS, Cobalt & Carbide)- For Aluminum, Plastic & Non-Ferrous Materials Mill Material LOC Cut Application Coating Type Flats Vendor 1/32 CO 3/32 3/16 2-1/4 CC GP For Aluminum & Non Ferrous U DE No MELIN ME $ /64 CO 9/64 3/16 2-1/4 CC GP For Aluminum & Non Ferrous U DE No MELIN ME /2- $ /16 CO 3/16 3/16 2-1/4 CC GP For Aluminum & Non Ferrous U DE No MELIN ME $ /64 CO 15/64 3/16 2-1/4 CC GP For Aluminum & Non Ferrous U DE No MELIN ME /2- $ /8 3/16 1/4 5/16 3/8 7/16 CAR 5/16 1/8 2-3/8 CC GP For Aluminum & Non Ferrous U SE - YG1 X-Power YG-EM93125 $20.40 C CAR 3/8 3/8 3-1/16 CC GP For Aluminum & Non Ferrous U DE Yes MELIN ME-MG $36.79 CAR 1/2 1/8 1-1/2 NC GP For Aluminum & Non Ferrous U SE - IMCO Micrograin IMCO $10.07 C CO 3/8 3/8 2-3/8 NC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-AN $18.72 CO 3/8 3/8 2-9/16 CC GP For Aluminum & Non Ferrous U SE Yes MORSE MCT $28.24 HSS 3/8 3/8 2-5/16 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $11.05 C CAR 3/8 3/16 3-1/8 CC GP For Aluminum & Non Ferrous U SE - YG1 X-Power YG-EM93126 $22.05 C CAR 1/2 3/8 3-1/4 CC GP For Aluminum & Non Ferrous U DE Yes MELIN ME-MG $35.45 CAR 5/8 3/16 2 CC GP For Aluminum & Non Ferrous U SE No MELIN ME-AMG-606- $13.43 CO 1/2 3/8 2-11/16 CC GP For Aluminum & Non Ferrous U SE Yes MORSE MCT $29.13 CO 7/16 3/8 3-1/8 CC GP For Aluminum & Non Ferrous U DE Yes MELIN ME $26.04 CO 1/2 3/8 2-3/8 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $15.89 CAR 1/2 1/4 3-1/2 CC GP For Aluminum & Non Ferrous U SE - YG1 X-Power YG-EM93127 $31.02 C CAR 5/8 3/8 3-1/2 CC GP For Aluminum & Non Ferrous U DE Yes MELIN ME-MG $42.64 CAR 3/4 1/4 2-1/2 NC GP For Aluminum & Non Ferrous U SE - IMCO Micrograin IMCO $17.09 C CO 1/2 3/8 3-1/8 CC GP For Aluminum & Non Ferrous U DE Yes MELIN ME $26.85 CO 5/8 3/8 3-1/16 CC GP For Aluminum & Non Ferrous U SE Yes MORSE MCT $29.13 CO 5/8 3/8 3-1/16 NC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-AN $18.72 CO 5/8 3/8 2-7/16 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $15.87 C CAR 3/4 3/8 3-1/2 CC GP For Aluminum & Non Ferrous U DE Yes MELIN ME-MG $48.14 CO 3/4 3/8 2-1/2 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $17.42 C CAR 3/4 3/8 3-1/2 CC GP For Aluminum & Non Ferrous U DE Yes MELIN ME-MG $49.03 CAR 3/4 3/8 4 CC GP For Aluminum & Non Ferrous U SE - YG1 X-Power YG-EM93129 $47.22 C CAR 1 3/8 2-1/2 CC GP For Aluminum & Non Ferrous U SE No MELIN ME-AMG $25.75 CO 3/4 3/8 2-1/2 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $17.42 C CO 3/4 3/8 2-1/2 CC GP For Aluminum & Non Ferrous U SE - YG1 YG-EM41305 $13.70 C CO 3/4 3/8 3-5/16 NC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-AN $21.39 CO 3/4 3/8 3-5/16 CC GP For Aluminum & Non Ferrous U SE Yes MORSE MCT $36.11 HSS 3/4 3/8 2-1/2 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $12.43 C CAR 1 7/16 2-3/4 CC GP For Aluminum & Non Ferrous U SE No MELIN ME-AMG $36.88 CO 1 1/2 3 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $24.80 C 15/32 CO 13/16 1/2 3-3/4 NC GP For Aluminum & Non Ferrous U DE Yes MELIN ME $ /2 CAR 7/8 1/2 4-1/4 CC GP For Aluminum & Non Ferrous U SE - YG1 X-Power YG-EM93130 $71.42 C CAR 1 1/2 3 CC GP For Aluminum & Non Ferrous U SE No MELIN ME-AMG $44.04 CO 1 1/2 3 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $26.80 C CO 1 1/2 3 NC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $27.36 CO 1 1/2 4 CC GP For Aluminum & Non Ferrous U SE Yes MORSE MCT $45.14 HSS 1 1/2 3 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $16.32 C 17/32 CO 1-1/8 1/2 3-1/8 NC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $ /16 5/8 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 1-1/4 9/16 3-1/2 CC GP For Aluminum & Non Ferrous U SE No MELIN ME-AMG $75.69 HSS 1-1/8 1/2 3-1/8 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $22.29 C CAR 1-1/4 5/8 3-1/2 CC GP For Aluminum & Non Ferrous U SE No MELIN ME-AMG $84.03 CO 1-1/8 1/2 3-1/8 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $36.20 CO 1-1/8 5/8 5 CC GP For Aluminum & Non Ferrous U DE Yes MELIN ME $56.54 CO 1-3/8 5/8 3-1/2 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $36.20 CO 1-3/8 5/8 3-1/2 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $40.16 C CO 2 5/8 4-1/8 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A-2020-M $49.13 HSS 1-3/8 5/8 3-1/2 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $24.93 C 11/16 CO 1-5/16 1/2 3-5/16 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $ /4 & Larger Sizes Continued On Following Page Master Catalog 401 Code CARIDE INSERTS DEURRING

134 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-2 FLUTE/ALL END 2 FLUTE ALL END ENDMILLS (continued) HSS, Cobalt & Carbide For Aluminum, Plastic & Non-Ferrous Materials 2 Flute all End Endmills (HSS, Cobalt & Carbide)- For Aluminum, Plastic & Non-Ferrous Materials (continued) Mill 3/4 Material LOC Cut Application Coating Type Flats Vendor Master Catalog CAR 1-1/2 3/4 4 CC GP For Aluminum & Non Ferrous U SE No MELIN ME-AMG $ CO 1-5/8 3/4 3-7/8 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $45.11 C CO 1-5/16 5/8 3-7/16 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $43.52 CO 1-5/8 3/4 3-7/8 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $44.79 CO 1-5/8 5/8 5-3/8 CC GP For Aluminum & Non Ferrous U SE Yes MORSE MCT $77.92 HSS 1-5/8 3/4 3-7/8 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $29.60 C HSS 1-5/16 3/4 5 NC GP For Aluminum & Non Ferrous U DE Yes TMX I $52.72 C 13/16 CO 1-1/2 1/2 3-1/2 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $ /8 CO 2 7/8 4-1/4 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $45.77 C CO 1-1/2 1/2 3-1/2 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $ /16 CO 1-1/2 1/2 3-1/2 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $ CO 2-1/ /4 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $72.04 C CO 2-1/4 3/4 4-1/2 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A $70.68 CO /2 CC GP For Aluminum & Non Ferrous U SE Yes MELIN ME-A-3232-M $83.58 CO 2-1/ /4 CC GP For Aluminum & Non Ferrous U SE Yes MORSE MCT $ HSS 2-1/ /4 CC GP For Aluminum & Non Ferrous U SE Yes TMX I $58.85 C 3 FLUTE ALL END ENDMILLS Cobalt & Carbide For Finishing Non-Ferrous Materials & Hard Alloys 3 Flute all End Endmills (Cobalt & Carbide)- For Finishing Non-Ferrous Materials & Hard Alloys Mill Material LOC Cut Application Coating Type Flats Vendor 1/16 CAR 1/8 1/8 1-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMGS-402- $8.79 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 CAR 1/2 1/8 1-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMG-404- $9.31 CAR 1/2 1/8 1-1/2 NC Light Mach-Aluminum/Non-Ferrous A SE - IMCO Spector IMCO $12.16 C CO 3/8 3/8 2-5/16 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $20.46 CAR 5/16 3/16 1-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMGS-606- $11.65 CAR 5/8 3/16 2 NC Light Mach-Aluminum/Non-Ferrous A SE - IMCO Spector IMCO $15.91 C CO 1/2 3/8 2-3/8 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $20.86 CAR 1/2 1/4 2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMGS-808- $13.72 CAR 3/4 1/4 2-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMG-808- $16.94 CAR 3/4 1/4 2-1/2 NC Light Mach-Aluminum/Non-Ferrous A SE - IMCO Spector IMCO $20.88 C CO 5/8 3/8 2-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $21.51 CAR 1/2 5/16 2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMGS $20.68 CO 3/4 3/8 2-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $23.01 CAR 5/8 3/8 2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMGS $25.42 CO 3/4 3/8 2-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $23.15 CAR 1 7/16 2-3/4 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMG $36.88 CO 1-3/4 1/2 3-3/4 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E-1614-L $39.44 CAR 5/8 1/2 2-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMGS $40.44 CAR 1 1/2 3 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMG $44.04 CO 1-1/4 1/2 3-1/4 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $35.09 CAR 3/4 5/8 3 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMGS $78.51 CAR 1-1/4 5/8 3-1/2 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMG $84.03 CO 1-5/8 5/8 3-3/4 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $48.94 CAR 1-1/2 3/4 4 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMG $ CO 1-5/8 1/2 3-5/8 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $ /8 CO 1-7/8 3/4 4-1/8 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $ ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 1-1/2 1 4 CC Light Mach-Aluminum/Non-Ferrous U SE No MELIN ME-EMG $ CO 1-7/8 3/4 4-1/8 CC Light Mach-Aluminum/Non-Ferrous U SE Yes MELIN ME-E $85.89 Code Code

135 ENDMILLS-4 FLUTE/ALL END 4 FLUTE ALL END ENDMILLS Cobalt & Carbide For Steels & Stainless Steels ALSO AVAILALE! 4 Flute all End Endmills (HSS, Cobalt & Carbide)- For Steels & Stainless Steels Mill Material LOC Cut Application Coating Type Flats Vendor 1/16 CAR 3/16 1/8 1-1/2 CC General Purpose U SE No MELIN ME-CCMG-402- $9.31 1/8 CAR 5/16 1/8 2-3/8 CC GP For Steels U SE - YG1 X-POWER YG-EM93134 $23.54 C CAR 3/8 3/8 3-1/16 CC General Purpose U DE Yes MELIN ME-DDMG $36.79 CAR 1/2 1/8 1-1/2 CC GP For Steels L SE - YG1 YG-EM43558TE $11.17 C CAR 1/2 1/8 1-1/2 CC GP For Steels L SE - YG1 YG-EM43558TF $10.94 C CO 3/8 3/8 2-5/16 NC General Purpose U SE Yes TMX I $22.82 C CO 3/8 3/8 2-5/16 CC General Purpose U SE Yes MELIN ME-CC $24.22 HSS 3/8 3/8 2-5/16 NC General Purpose U SE Yes TMX I $17.13 C 5/32 CO 7/16 3/8 2-5/16 NC General Purpose U SE Yes MELIN ME-CC $ /16 CAR 3/8 3/16 2 NC General Purpose A DE - IMCO Spector IMCO $22.89 C CAR 1/2 3/8 3-1/4 CC General Purpose U DE Yes MELIN ME-DDMG $35.45 CAR 5/8 3/16 2 CC GP For Steels L SE - YG1 YG-EM43565TF $15.20 C CO 1/2 3/8 2-3/8 NC General Purpose U SE Yes TMX I $22.42 C CO 1/2 3/8 2-3/8 CC General Purpose U SE Yes MELIN ME-CC $24.22 CO 1/2 3/8 3-1/4 CC General Purpose U DE Yes MELIN ME-DD $ /32 CAR 5/8 1/4 2-1/2 CC GP For Steels U SE - YG1 YG-EM43570 $15.17 C 1/4 5/16 3/8 7/16 1/2 CAR 1/2 1/4 3-1/2 CC GP For Steels U SE - YG1 X-POWER YG-EM93136 $35.77 C CAR 5/8 3/8 3-1/2 CC General Purpose U DE Yes MELIN ME-DDMG $42.64 CAR 3/4 1/4 2-1/2 CC GP For Steels L SE - YG1 YG-EM43573TE $22.17 C CAR 3/4 1/4 2-1/2 CC GP For Steels L SE - YG1 YG-EM43573TF $21.55 C CO 5/8 3/8 2-7/16 NC General Purpose U SE Yes TMX I $22.42 C CO 5/8 3/8 3-3/8 CC General Purpose U DE Yes MELIN ME-DD $37.16 CO 3/4 3/8 2-9/16 CC General Purpose U SE Yes MELIN ME-CC $24.22 CO 1-1/4 3/8 3-1/16 NC General Purpose U SE Yes MELIN ME-CC-1208-L $28.98 HSS 5/8 3/8 2-7/16 NC GeneralPurpose U SE Yes TMX I $17.13 C CAR 3/4 3/8 3-1/2 CC GeneralPurpose U DE Yes MELIN ME-DDMG $48.14 CAR 13/16 5/16 2-1/2 CC GeneralPurpose U SE No MELIN ME-CCMG $21.45 CO 3/4 3/8 2-1/2 CC GeneralPurpose U SE Yes TMX I $22.42 C CO 1 3/8 2-3/4 CC GeneralPurpose U SE Yes MELIN ME-CC $24.22 CAR 3/4 3/8 3-1/2 CC GeneralPurpose U DE Yes MELIN ME-DDMG $49.03 CAR 1 3/8 2-1/2 NC GeneralPurpose A SE - IMCOSpector IMCO $33.36 C CO 3/4 3/8 2-1/2 NC GeneralPurpose U SE Yes TMX I $24.59 C CO 3/4 3/8 3-1/2 CC GeneralPurpose U DE Yes MELIN ME-DD $37.16 CO 1 3/8 2-3/4 CC GeneralPurpose U SE Yes MELIN ME-CC $26.10 HSS 3/4 3/8 2-1/2 NC GeneralPurpose U SE Yes TMX I $17.13 C HSS 1 3/8 2-11/16 CC GeneralPurpose U SE Yes TMX I $18.10 C CO 1 3/8 2-11/16 CC GeneralPurpose U SE Yes MELIN ME-CC $34.30 CAR 1 1/2 3 CC GPForSteels L SE - YG1 YG-EM43593TE $50.24 C CAR 1 1/2 3 CC GPForSteels L SE - YG1 YG-EM43593TF $49.10 C CO 1 3/8 2-11/16 CC GeneralPurpose U SE Yes MELIN ME-CC $34.30 CO 1-1/4 1/2 3-1/4 NC GeneralPurpose U SE Yes TMX I $38.18 C CO 1-1/4 1/2 3-1/4 CC GeneralPurpose U SE Yes MINICUT MN $37.97 C CO 1-1/4 1/2 3-1/4 NC GeneralPurpose U SE Yes MELIN ME-CC $33.98 CO 3 1/2 5 NC GeneralPurpose U SE Yes MELIN ME-CC-1616-E $ /16 CAR 1-1/4 9/16 3-1/2 CC GeneralPurpose U SE No MELIN ME-CCMG $ /8 ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CAR 1-1/4 5/8 3-1/2 CC GeneralPurpose U SE No MELIN ME-CCMG $84.03 CO 1-5/8 5/8 3-3/4 NC GeneralPurpose U SE Yes TMX I $51.49 C CO 1-3/8 5/8 5 CC GeneralPurpose U DE Yes MELIN ME-DD $71.07 CO 1-5/8 5/8 3-3/4 CC GeneralPurpose U SE Yes MELIN ME-CC $ Master Catalog 403 Code 3/4 & Larger Sizes Continued on Following Page CARIDE INSERTS DEURRING

136 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ENDMILLS-ALL END 4 FLUTE ALL END ENDMILLS (continued) Cobalt & Carbide For Steels & Stainless Steels. 4 Flute all End Endmills (HSS, Cobalt & Carbide)- For Steels & Stainless Steels (continued) Mill 3/4 7/8 1 Material LOC Cut Application Coating Type Flats Vendor Master Catalog ENDMILL LEGEND MATERIAL CUT COATING TYPE CO= M42 Cobalt CC= Center Cutting U= Uncoated SE= Single End CAR= Carbide NC= Non-Center A= AlTiN Coated DE= Double End HSS= High Speed Steel Cutting L= TiAlN Coated STE= Stellar One- HSS w/ Toughness of Cobalt I= TiN Coated C= TiCN Coated CO 1-5/8 3/4 3-7/8 NC General Purpose U SE Yes TMX I $57.29 C CO 1-5/8 3/4 3-7/8 CC General Purpose U SE Yes MELIN ME-CC $55.97 CO 1-5/8 3/4 5-5/8 CC General Purpose U DE Yes MELIN ME-DD $95.66 CO 1-7/8 7/8 4-1/8 CC General Purpose U SE Yes MELIN ME-CC $79.98 HSS 1-7/8 7/8 4-1/8 NC General Purpose U SE Yes TMX I $62.08 C CAR 1-1/2 1 4 CC General Purpose L SE No TMX I $ C CO /2 NC General Purpose U SE Yes TMX I $97.39 C CO /2 CC General Purpose U SE Yes MELIN ME-CC $ /2 CO 2 1-1/4 4-1/2 NC General Purpose U SE Yes TMX I $ C ALL END MILLS Solid Carbide-Center Cutting, 30 Helix Long Length LONG REACH ALL END MILLS 2 & 4 Flute Center Cutting - 30 Helix Flute Length Flute Length Neck Length 2-Flute 2-Flute 4-Flute 4-Flute 3/16 3/16 2-1/2 3/4 MI-LL1872 MI-LL1874 $ /4 1/ /8 MI-LL2502 MI-LL2504 $ /16 5/ /8 MI-LL3122 MI-LL3124 $ /8 3/ /8 MI-LL3752 MI-LL3754 $ /16 7/16 4-1/2 2 MI-LL4372 MI-LL4374 $ /2 1/2 4-1/2 2 MI-LL5002 MI-LL5004 $ /8 5/ /4 MI-LL6252 MI-LL6254 $ /4 3/ /4 MI-LL7502 MI-LL7504 $ /4 MI-LL0012 MI-LL0014 $ Micro grain carbide Neck diameter is reduced.020 on all sizes for required clearance in long reach applications Center cutting 30 helix Maximum T.I.R /16 3/16 3 3/8 1-5/8 MI-LR1872 MI-LR1874 $ /4 1/4 4 1/2 2 MI-LR2502 MI-LR2504 $ /16 5/16 4 5/8 2 MI-LR3122 MI-LR3124 $ /8 3/8 4 3/4 2 MI-LR3752 MI-LR3754 $ /16 7/ /2 MI-LR4372 MI-LR4374 $ /2 1/ /2 MI-LR5002 MI-LR5004 $ /8 5/ /4 3-1/4 MI-LR6252 MI-LR6254 $ /4 3/ /2 3 MI-LR7502 MI-LR7504 $ /2 3 MI-LR0012 MI-LR0014 $ Extra Long Length Flute Length 2-Flute 4-Flute Code 3/16 3/ /8 MI-EL1872 MI-EL1874 $ /4 1/ /2 MI-EL2502 MI-EL2504 $ /16 5/ /8 MI-EL3122 MI-EL3124 $ /8 3/ /4 MI-EL3752 MI-EL3754 $ /16 7/ MI-EL4372 MI-EL4374 $ /2 1/2 6 3 MI-EL5002 MI-EL5004 $ /8 5/8 6 3 MI-EL6252 MI-EL6254 $ /4 3/4 6 3 MI-EL7502 MI-EL7504 $ MI-EL0012 MI-EL0014 $ CHAMFER MILLS Carbide 4 Flute-Single End Included Angle flute 90 4 flute 60 4 flute Angle Length 3/16 2-1/ IT $ /4 2-1/ IT $ /16 2-1/ IT $ /8 2-1/ IT $ / IT $ /16 2-1/ IT $ /4 2-1/ IT $ /16 2-1/ IT $ /8 2-1/ IT $ / IT $ /16 2-1/ IT $ /4 2-1/ IT $ /16 2-1/ IT $ /8 2-1/ IT $ / IT $56.30 C

137 ENDMILLS-DRILL POINT SOLID CARIDE DRILL MILLS The 5-in-1 Tool! Premium sub-micron C-2 carbide Ideal for chamfering, countersinking, drilling, side milling and spotting Made in the NEW ITEM! DRILL POINT ENDMILLS & DRILL MILLS Center Cutting, Single End Cobalt -Uncoated 60, 82, 90, 100 & 120 Chamfer, Countersink, Drill, Side Mill & Spot Drill ALL WITH THE SAME TOOL! 2 FLUTE Uncoated TiAlN Coated Mill LOC /8 1/2 1/8 1-1/2 MO-DM MO-DM $11.15 MO-DM MO-DM $ /16 5/8 3/16 2 MO-DM MO-DM $14.63 MO-DM MO-DM $ /4 3/4 1/4 2-1/2 MO-DM MO-DM $19.76 MO-DM MO-DM $ /16 13/16 5/16 2-1/2 MO-DM MO-DM $26.14 MO-DM MO-DM $ /8 1 3/8 2-1/2 MO-DM MO-DM $31.26 MO-DM MO-DM $ /16 1 7/16 2-3/4 MO-DM MO-DM $43.76 MO-DM MO-DM $ /2 1 1/2 3 MO-DM MO-DM $56.17 MO-DM MO-DM $ /8 1-1/4 5/8 3-1/2 MO-DM MO-DM $88.99 MO-DM MO-DM $ /4 1-1/2 3/4 4 MO-DM MO-DM $ MO-DM MO-DM $ FLUTE Uncoated TiAlN Coated Mill LOC /8 1/2 1/8 1-1/2 MO-DM MO-DM $11.15 MO-DM MO-DM $ /16 5/8 3/16 2 MO-DM MO-DM $14.63 MO-DM MO-DM $ /4 3/4 1/4 2-1/2 MO-DM MO-DM $19.76 MO-DM MO-DM $ /16 13/16 5/16 2-1/2 MO-DM MO-DM $26.14 MO-DM MO-DM $ /8 1 3/8 2-1/2 MO-DM MO-DM $31.26 MO-DM MO-DM $ /16 1 7/16 2-3/4 MO-DM MO-DM $43.76 MO-DM MO-DM $ /2 1 1/2 3 MO-DM MO-DM $56.17 MO-DM MO-DM $ /8 1-1/4 5/8 3-1/2 MO-DM MO-DM $88.99 MO-DM MO-DM $ /4 1-1/2 3/4 4 MO-DM MO-DM $ MO-DM MO-DM $ C Mill 1/8 3/16 1/4 5/16 3/8 7/16 LOC Drill Point 3/8 3/8 2-5/16 60 ME-A1204DP60 $ /8 3/8 2-5/16 82 ME-A1204DP82 $ /8 3/8 2-5/16 90 ME-A1204DP $ /16 3/8 2-5/16 60 ME-A1206DP60 $ /16 3/8 2-5/16 82 ME-A1206DP82 $ /16 3/8 2-5/16 90 ME-A1206DP $ /8 3/8 2-7/16 60 ME-A1208DP60 $ /8 3/8 2-7/16 82 ME-A1208DP82 $ /8 3/8 2-7/16 90 ME-A1208DP $ /32 3/8 2-15/32 60 ME-A1210DP60 $ /32 3/8 2-15/32 82 ME-A1210DP82 $ /32 3/8 2-15/32 90 ME-A1210DP $ /4 3/8 2-1/2 60 ME-A1212DP60 $ /4 3/8 2-1/2 82 ME-A1212DP82 $ /4 3/8 2-1/2 90 ME-A1212DP $ /32 3/8 2-23/32 82 ME-A1214DP82 $ /32 3/8 2-23/32 90 ME-A1214DP $20.03 CARIDE DRILL-MILLS Solid carbide Center cutting 30 right hand helix 120 included angle Economical- drill and mill with one tool! Drill & Mill With One Tool! Mill 1/2 9/16 5/8 3/4 7/8 1 LOC Drill Point 1-1/4 1/2 3-1/4 60 ME-A1616DP60 $ /4 1/2 3-1/4 82 ME-A1616DP82 $ /4 1/2 3-1/4 90 ME-A1616DP $ /32 1/2 3-13/32 82 ME-A1618DP82 $ /32 1/2 3-13/32 90 ME-A1618DP $ /8 5/8 3-3/4 60 ME-A2020DP60 $ /8 5/8 3-3/4 82 ME-A2020DP82 $ /8 5/8 3-3/4 90 ME-A2020DP $ /16 3/4 3-15/16 60 ME-A2424DP60 $ /16 3/4 3-15/16 90 ME-A2424DP $ /16 3/4 3-15/ ME-A2424DP120 $ /16 3/4 4-3/16 60 ME-A2428DP60 $ /16 3/4 4-3/16 90 ME-A2428DP $ /4 4-1/4 60 ME-A2432DP60 $ /4 4-1/4 90 ME-A2432DP $ /4 4-1/4 120 ME-A2432DP120 $57.43 Size Length of Cut Master Catalog 405 1/8 5/8 2 1/8 IT $ /16 3/4 2-1/2 3/16 IT $ /32 3/4 2-1/2 1/4 IT $ / /2 1/4 IT $ / /2 5/16 IT $ / /16 IT $ / /8 IT $ / /8 IT $ / /16 IT $ / /16 IT $ / /2 IT $ / /2 IT $41.17 CARIDE INSERTS DEURRING

138 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD MINIATURE ENDMILLS-SOLID CARIDE SQUARE END-2 & 4 FLUTE CENTER CUTTING, 30 HELIX 1/8, 1-1/2 Manufactured from the highest quality carbide material with 10% cobalt Sinter Hipped- C2 grade, micrograin carbide Miniature and subminiature Cutting LOC 2 Flute 4 Flute MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $10.91 ALL END-2 & 4 FLUTE Manufactured from the highest quality carbide material with 10% cobalt Sinter Hipped- C2 grade, micro-grain carbide Miniature and subminiature Cutting LOC 2 Flute 4 Flute MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $10.00 Cutting 2 Flute 4 Flute Master Catalog LOC MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $5.91 Cutting LOC 2 Flute 4 Flute MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $10.00 Cutting LOC 2 Flute 4 Flute C MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $5.91 Cutting LOC 2 Flute 4 Flute MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $ MO MO $8.64 Full Line Available! Please call for more information.

139 MINIATURE ENDMILLS-SOLID CARIDE MINATURE ALL END MILLS 2 Flute - Center Cutting - 30 Helix MINATURE END MILLS 2 Flute - Center Cutting - 30 Helix Cutter D1 D2 L1 Flute L MI-MR0102 $ MI-MR0112 $ /8 1-1/ MI-MR0122 $ MI-MR0132 $ MI-MR0142 $ MI-MR0152 $ MI-MR0162 $ /8 1-1/ MI-MR0172 $ MI-MR0182 $ MI-MR0192 $ MI-MR0202 $ MI-MR0212 $ /8 1-1/ MI-MR0222 $ MI-MR0232 $ MI-MR0242 $ MI-MR0252 $ MI-MR0262 $ MI-MR0272 $ /8 1-1/ MI-MR0282 $ MI-MR0292 $ MI-MR0302 $20.25 MINATURE STU ALL END MILLS 2 Flute - Center Cutting - 30 Helix Cutter D1 D2 L1 Flute L MI-RME0102 $ MI-RME0112 $ /8 1-1/ MI-RME0122 $ MI-RME0132 $ MI-RME0142 $ MI-RME0152 $ MI-RME0162 $ /8 1-1/ MI-RME0172 $ MI-RME0182 $ MI-RME0192 $ MI-RME0202 $ MI-RME0212 $ /8 1-1/ MI-RME0222 $ MI-RME0232 $ MI-RME0242 $ MI-RME0252 $ MI-RME0262 $ MI-RME0272 $ /8 1-1/ MI-RME0282 $ MI-RME0292 $ MI-RME0302 $16.30 MINATURE STU END MILLS 2 Flute Center Cutting - 30 Helix Cutter D1 D2 L1 Flute L MI-MS0102 $ MI-MS0112 $ /8 1-1/ MI-MS0122 $ MI-MS0132 $ MI-MS0142 $ MI-MS0152 $ MI-MS0162 $ /8 1-1/ MI-MS0172 $ MI-MS0182 $ MI-MS0192 $ MI-MS0202 $ MI-MS0212 $ /8 1-1/ MI-MS0222 $ MI-MS0232 $ MI-MS0242 $ MI-MS0252 $ MI-MS0262 $ MI-MS0272 $ /8 1-1/ MI-MS0282 $ MI-MS0292 $ MI-MS0302 $18.98 Cutter D1 D Master Catalog 407 L1 Flute L MI-SME0052 $ MI-SME0062 $ /8 1-1/ MI-SME0072 $ MI-SME0082 $ MI-SME0092 $ MI-SME0102 $ MI-SME0112 $ /8 1-1/ MI-SME0122 $ MI-SME0132 $ MI-SME0142 $ MI-SME0152 $ MI-SME0162 $ /8 1-1/ MI-SME0172 $ MI-SME0182 $ MI-SME0192 $ MI-SME0202 $ MI-SME0212 $ /8 1-1/ MI-SME0222 $ MI-SME0232 $ MI-SME0242 $ MI-SME0252 $ MI-SME0262 $ MI-SME0272 $ /8 1-1/ MI-SME0282 $ MI-SME0292 $ MI-SME0302 $16.20 CARIDE INSERTS DEURRING

140 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING CORNER ROUNDING ENDMILLS CORNER ROUNDING ENDMILLS High Speed Steel Used for rounding corners HSS, right hand cut Weldon shank Form relieved- can be re-sharpened many times without changing contour CORNER ROUNDING ENDMILLS Single End 3 Flute, Cobalt M-42 Tolerance +.001/-.001 Rad Flute Length Radius 1/16 3/8 7/16 2-1/2 ME-R-1202 $ /16 1/2 1/2 2-5/8 ME-R-1602 $ /32 3/8 1/2 2-1/2 ME-R-1203 $ /32 1/2 1/2 2-5/8 ME-R-1603 $ /8 1/2 5/8 2-7/8 ME-R-1604 $ /32 1/2 5/8 2-7/8 ME-R-1605 $ /16 1/2 3/4 3 ME-R-1606 $ /32 1/2 7/8 3 ME-R-1607 $ /4 1/2 7/8 3 ME-R-1608 $ /4 3/4 7/8 3-1/4 ME-R-2408 $ /16 1/2 1 3 ME-R-1610 $ /8 1/2 1-1/8 3-1/4 ME-R-1612 $ /8 3/4 1-1/8 3-1/2 ME-R-2412 $ /16 1/2 1-1/4 3-1/2 ME-R-1614 $ CORNER ROUNDING ENDMILLS Double End, 3 Flute Solid Micrograin Carbide Cutter NEW ITEM! 3/4 7/8 1 Radius Minor Radius Minor Radius Size Cutter Minor CORNER ROUNDING END MILLS Carbide Tipped 1/16 3/8 7/16 2-1/2 I $ /8 3/4 1-1/4 3-1/2 I $ /32 3/8 1/2 2-1/2 I $ /8 7/8 1-1/4 3-3/4 I $ /8 3/8 5/8 2-1/2 I $ /16 3/4 1-3/8 3-3/4 I $ /8 1/2 5/8 3 I $ / /8 4 I $ /32 1/2 3/4 3 I $ /2 3/4 1-1/2 3-7/8 I $ /16 1/2 7/8 3 I $ / /2 4-1/8 I $ /4 1/2 1 3 I $ /8 3/4 1-5/8 4 I $ /4 3/ /4 I $ / /8 4 I $ /16 1/2 1-1/8 3-1/4 I $ /4 3/4 1-7/8 4 I $ /16 5/8 1-1/8 3-1/2 I $ / /8 4 I $ /16 3/4 1-1/8 3-1/4 I $ /4 2-9/16 4 I $ /8 1/2 1-1/4 3-1/2 I $ /16 4 I $ /2 IT $ /2 IT $ /2 IT $ /2 IT $ IT $ IT $ C ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD 1/8 3/16 1/4 Radius Minor IT (1/64) IT IT IT (1/32) IT (1/64) IT (1/32) IT (1/16) IT /2 IT (1/64) /2 IT /2 IT /2 IT (1/32) /2 IT /2 IT (1 MM) /2 IT (3/64) /2 IT /2 IT /2 IT (1/16) /2 IT /2 IT /2 IT $21.73 $23.49 $ Master Catalog 3/8 1/2 5/8 3/4 Radius Radius Minor.0781 (5/64) /2 IT (2MM) /2 IT (3/32) /2 IT (2.5MM) /2 IT (7/64) /2 IT (3MM) /2 IT (1/8) /2 IT (9/ IT (5/32) IT (4MM) IT (11/64) IT (3/16) IT (5MM) /2 IT (13/64) /2 IT (7/32) /2 IT (15/64) /2 IT (6MM) /2 IT (1/4) /2 IT (9/32) IT (19/64) IT (5/16) IT $50.35 $78.70 $90.10 $ C

141 SOLID CARIDE ORING TOOLS HELICAL ACK RAKE ORING TOOLS Neck is centered to shank for use in jig boring machines. The helical grind provides an ideal top rake for better chip control. Left-hand boring tools also available.. D2 L1 ore. D1 ore Depth L2 Neck. N / MI-H / MI-H / MI-H / MI-H / MI-H / MI-H / MI-H / MI-H /8 1-1/2 1/ MI-H / MI-H / MI-H / MI-H / MI-H / MI-H / MI-H / MI-H MI-H /4 MI-H MI-H MI-H / /4 MI-H MI-H / MI-H /2 MI-H MI-H / MI-H /4 2-1/2 1-1/2 MI-H MI-H /2 MI-H /4 MI-H MI-H MI-H / /4 MI-H MI-H / MI-H /2 MI-H MI-H / MI-H /2 MI-H /4 2-1/2 1 MI-H / MI-H /4 MI-H MI-H /16 2-1/ / MI-H /4 MI-H MI-H / / MI-H /4 MI-H /8 2 MI-H / MI-H /2 MI-H /2 MI-H MI-H /2 MI-H /2 3 MI-H /2 MI-H MI-H /2 MI-H N/C GENERATION meter to Minimum ore Maximum ore Depth Overall Length +1/64 $31.25 $24.10 $25.80 $27.95 $25.80 $27.95 $38.25 $53.10 $68.40 $74.75 $82.05 $ RAZED ORING TOOLS A lockdown groove completely encircles the tool so that the cutting point can be turned to any desired position. A D C 2 3/4 MI-P1 5/16 2-3/8 1-1/8 MI-P2 2-3/4 1-1/2 MI-P3 2-3/16 15/16 MI-P4 3/8 3/8 2-21/ /32 MI-P5 3-1/8 1-7/8 MI-P6 2-3/8 1-1/8 MI-P7 7/ / /16 MI-P8 3-1/2 2-1/4 MI-P9 2-1/4 3/4 MI-P10 5/16 2-5/8 1-1/8 MI-P /2 MI-P12 2-5/8 1-1/8 MI-P13 1/2 3/8 3-3/ /16 MI-P14 3-3/4 2-1/4 MI-P /2 MI-P16 7/16 3-3/4 2-1/4 MI-P17 4-1/2 3 MI-P18 2-1/4 3/4 MI-P19 5/16 2-5/8 1-1/8 MI-P /2 MI-P21 2-5/8 1-1/8 MI-P22 7/16 3-3/ /16 MI-P23 5/8 3-3/4 2-1/4 MI-P /2 MI-P25 9/16 3-3/4 2-1/4 MI-P26 4-1/2 3 MI-P27 3-3/8 1-7/8 MI-P28 11/16 4-5/ /16 MI-P29 5-1/4 3-3/4 MI-P30 ORING TOOLS TiAlN Coated Ground w/ Helical Rake Min ore Radius Max Depth $30.10 $31.60 $35.60 Max-ore has a special helical flute for maximum shearing action with a better finish Eliptical neck for greater strength.375 IT / IT IT /16 2-1/2.500 IT IT IT /16 2-1/2.750 IT IT IT /16 2-1/2.500 IT IT IT IT /4 2-1/2 0.5 IT IT IT Tools Up to.490 Min. ore Available $24.07 $25.76 $25.76 $25.76 $ Master Catalog 409 CARIDE INSERTS DEURRING

142 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID CARIDE ORING ARS SOLID CARIDE ORING ARS Right Hand, With Radius, NC Generation Provides for vastly increased speed and feed rates in cutting aluminum, copper, stainless steels, high temperature alloys Manufactured with a 4RMS finish Mirror polished cutting surface Lockdown flat automatically locates tool on center Highly shock resistant, will not chip or break under normal machining conditions Made in the! Min. ore Max. ore Depth Proj /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ /8 1-1/ MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $28.89 Min. ore Master Catalog Max. ore Depth Proj /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /4 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /16 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ / MO $ / MO $ / MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ /8 2-1/ MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ / MO $ C

143 SOLID CARIDE ORING ARS SOLID CARIDE ORING TOOLS Lockdown flat automatically locates tool on center. Min. ore D1. D2 L1 Proj. P MAX. ore L2 Right Hand Left Hand.150 MI MI-L /8 1-1/ MI MI-L MI MI-L $ MI MI-L MI MI-L MI MI-L /8 1-1/ MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L /8 1-1/ MI MI-L MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L /8 1-1/ MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L /8 1-1/ MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L / MI MI-L MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L / MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L / MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L /4 2-1/ MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L /4 2-1/ MI MI-L MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L Min ore D1. D2 L1 Proj. P Max ore L2 Full Line Available! Please call for more information. Right Hand Left Hand.400 MI MI-L MI MI-L MI MI-L /16 2-1/ MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L /16 2-1/ MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L /16 2-1/ MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L /8 2-1/ MI MI-L MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L / MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L /8 2-1/ MI MI-L MI MI-L $ MI MI-L MI MI-L MI MI-L MI MI-L MI MI-L / MI MI-L $ MI MI-L MI MI-L / MI MI-L MI MI-L $ MI MI-L MI MI-L / MI MI-L MI MI-L $ MI MI-L MI MI-L / MI MI-L MI MI-L $ MI MI-L Additional sizes also available Master Catalog 411 CARIDE INSERTS DEURRING

144 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ORING HEAD/ORING ARS RAZED ORING ARS Style T Tip Right Left A C D T W L Hand Hand 1/4 4 1/ /16 3/16 1/4 MI-T250 MI-TL250 $ /16 5 5/ /16 1/4 5/16 MI-T312 MI-TL312 $ /8 6 3/ /16 1/4 5/16 MI-T375 MI-TL375 $ /2 7 1/ /8 1/4 1/2 MI-T500 MI-TL500 $ /8 8 5/ /8 1/4 5/8 MI-T625 MI-TL625 $ /4 9 3/ /8 1/4 5/8 MI-T750 MI-TL750 $ / /16 7/16 13/16 MI-T001 MI-TL001 $ Master Catalog QUANTITY DISCOUNTS! 3 PIECE ORING TOOL SET ORING HEADS Head Features: ar holder moves freely and smoothly. Design assures superior rigidity for chatter-free boring and precise hole size accuracy Hardened and ground adjusting screw designed for long lasting and trouble free use. Set includes: oring head, R8 boring shank and C-6 carbide tipped boring Head Size oring ar oring ar Qty Tool Capacity Set 2 7/8-20 1/2 9 pcs Up to 1/2 A $ /2-18 3/4 12 pcs Up to 3/4 A $ ORING HEAD SHANKS Made of high grade tool steel Hardened and ground R8, Morse Taper and Straight shanks Taper Of End Type 7/8" -20 Thread 1-1/2" -18 Thread R8 - A $19.00 A $19.00 MT2 Draw ar A $19.00 A $20.00 MT2 Tang End A $ MT3 Tang End A $20.00 A $20.00 MT3 Draw ar A $ MT4 Tang End A $25.00 A $25.00 # 30 Draw ar A $21.00 A $21.00 # 40 Draw ar A $27.00 A $ /2 SS - A $ /4 SS - A $19.00 A $ SS - A $20.00 A $ /4 SS - A $21.00 A $ /2 SS A $24.00 ar holder moves freely and smoothly Design assures superior rigidity for chatter-free boring and precise hole size accuracy Hardened and ground adjusting screw designed for long lasting and trouble free use Head Size Threads Tool Cap ORING AR SETS Five oring ars: 1/4, 3/8, 1/2, 5/8 and 3/4 RH #- MI-T-5 LH #- MI-TL-5 Set : $ Quantity Discounts 1 to 5 pcs. List 6 to 11 pcs. Save 3% 12 pcs. or more Save 5% Must be same part number 2" 1-1/2"-18 Up to 1/2" A $ " 7/8"-20 Up to 1/2" A $ " 1-1/2"-18 Up to 3/4" A $ " 1-1/2"-18 Up to 1" A $ PRECISION ORING HEADS FEATURES: Heavy duty construction offers smooth, chatter-free operation. Precision hardened steel with black oxide finish..001 direct diameter reading micrometer dial. Head. 2 Head Only HD-200 $ /2 R8 HD-R8250 $ /2 3/4 SS HD-SS250 $ R8 HD-R8300 $60.00 D

145 CARIDE TURNING TOOLS TURNING, FORMING & CUT-OFF Right & Left Hand All tools are ground with the required clearance angles. Carbide profusion=3 times thickness specified Tolerance on thickness ± Full Line Available! Please call for more information. Style LC Style LT Style RC Style RT 1/4 Square 6 $13.70 Ea. 9/32 Square 6 $14.35 Ea. 5/16 Square 6 $14.35 Ea. 3/8 Square 6 $14.55 Ea. Type Width Right Hand Left Hand Right Hand Left Hand Right Hand Left Hand Right Hand Left Hand Turning - MI-RT250 MI-LT250 MI-RT281 MI-LT281 MI-RT312 MI-LT312 MI-RT375 MI-LT375 Forming - MI-C250 MI-C 250 MI-C 281 MI-C 281 MI-C312 MI-C312 MI-C375 MI-C375 Cut-off.040 MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC Cut-off.060 MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC Cut-off MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC Cut-off MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC Cut-off MI-RC MI-LC *Ground to 6mm square shank. 7/16 Square 6 $18.10 Ea. 1/2 Square 6 $18.55 Ea. 5/8 Square 4 $24.20 Ea. 3/4 Square 4 $28.25 Ea. Type Width Right Hand Left Hand Right Hand Left Hand Right Hand Left Hand Right Hand Left Hand Turning - MI-RT437 MI-LT437 MI-RT500 MI-LT500 MI-RT 625 MI-LT 625 MI-RT750 MI-LT750 Forming - MI-C437 MI-C 437 MI-C500 MI-C500 MI-C625 MI-C625 MI-C750 MI-C750 Cut-off.060 MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC Cut-off.080 MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC Cut-off.100 MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC MI-RC MI-LC Cut-off.120 MI-RC MI-LC MI-RC MI-LC Cut-off MI-RC MI-LC MI-RC MI-LC Cut-off MI-RC MI-LC MI-RC MI-LC RAZED OX TURNING TOOLS For box-turning up to 5/8 depth per pass SPLIT-END ENGRAVING TOOLS 30,60 or 90 Included Angle - Relieved For Right Hand One End Split Two End Splits T Style Tip Right Left A C T W L Hand Hand 1/4 1/4 1-1/2 1/8 3/16 1/4 MI-T4 MI-TL4 $ /16 5/16 1-3/4 1/8 3/16 5/16 MI-T5 MI-TL5 $ /8 3/8 2 3/16 5/16 3/8 MI-T6 MI-TL6 $ /16 7/16 2-1/4 3/16 3/8 7/16 MI-T7 MI-TL7 $ /2 1/2 2-1/2 3/16 3/8 1/2 MI-T8 MI-TL8 $ /16 9/16 2-3/4 1/4 1/2 9/16 MI-T9 MI-TL9 $ /8 5/8 3 1/4 1/2 5/8 MI-T10 MI-TL10 $39.20 D L1 Split L /8 1-1/2 3/8 MI-RTC1251 MI-RSC1251 MI-RNC1251 $ /16 2 3/8 MI-RTC1871 MI-RSC1871 MI-RNC1871 $ /4 2-1/2 3/8 MI-RTC2501 MI-RSC2501 MI-RNC2501 $ /16 2-1/2 1/2 MI-RTC3121 MI-RSC3121 MI-RNC3121 $ /8 2-1/2 1/2 MI-RTC3751 MI-RSC3751 MI-RNC3751 $ /2 3 5/8 MI-RTC5001 MI-RSC5001 MI-RNC5001 $72.60 D L1 Split L /8 1-1/2 3/8 MI-RTC1252 MI-RSC1252 MI-RNC1252 $ /16 2 3/8 MI-RTC1872 MI-RSC1872 MI-RNC1872 $ /4 2-1/2 3/8 MI-RTC2502 MI-RSC2502 MI-RNC2502 $ /16 2-1/2 1/2 MI-RTC3122 MI-RSC3122 MI-RNC3122 $ /8 2-1/2 1/2 MI-RTC3752 MI-RSC3752 MI-RNC3752 $ /2 3 5/8 MI-RTC5002 MI-RSC5002 MI-RNC5002 $87.70 QUANTITY DISCOUNTS! Quantity Discounts 1 to 5 pcs. List 6 to 11 pcs. Save 3% 12 to 23 pcs. Save 5% 24 to 47 pcs. Save 7% 48 or more Save 10% Must be same part number meter to finish ground Split tolerance of tool center Split length in proportion to length of tool. Quantity Discounts 1 to 5 pcs. List 6 to 11 pcs. Save 3% 12 to 47 pcs. Save 5% 48 to 99 pcs. Save 7% 100 or more Save 10% Must be same part number Master Catalog 413 CARIDE INSERTS DEURRING

146 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS STANDARD RAZED TOOLS STYLE AR & AL Tool Style Square RH No. LH No. EA AR4 1/4 2 MI-AR4 MI-AL4 $12.25 AR5 5/16 2-1/4 MI-AR5 MI-AL5 $12.45 AR6 3/8 2-1/2 MI-AR6 MI-AL6 $13.00 AR7 7/16 3 MI-AR7 MI-AL7 $13.45 AR8 1/2 3-1/2 MI-AR8 MI-AL8 $13.70 AR10 5/8 4 MI-AR10 MI-AL10 $22.40 AR12 3/4 4-1/2 MI-AR12 MI-AL12 $29.85 STYLE R & L SHANK TIP Right Left A C T W L R Hand Hand 3/8 3/8 2-1/2 1/8 1/4 1/2 1/64 MI-R6 MI-L6 $ /16 7/16 3 1/8 1/4 1/2 1/32 MI-R7 MI-L7 $ /2 1/2 3-1/2 1/8 1/4 5/8 1/32 MI-R8 MI-L8 $ /8 5/8 4 5/32 3/8 3/4 1/32 MI-R10 MI-L10 $ /4 3/4 4-1/2 3/16 7/16 13/16 1/32 MI-R12 MI-L12 $30.10 STYLE IDLT SHANK Thread Neck Right Left A C. Length Hand Hand 3/8 3/8 2-1/ MI-IDRT60 MI-IDLT60 $ /8 3/8 2-1/ MI-IDRT61 MI-IDLT61 $ /2 1/2 3-1/ MI-IDRT80 MI-IDLT80 $ /2 1/2 3-1/ MI-IDRT81 MI-IDLT81 $27.40 AR Style L Style Style IDRT Quantity Discounts 1 to 5 pcs. List 6 to 11 pcs. Save 3% 12 to 23 pcs. Save 5% 24 to 47 pcs. Save 7% 48 or more Save 10% Must be same part number TOOLHOLDERS STYLE CT SHANK TIP A C D T W L 1/ /16 1/8 3/16 3/4 MI-CT122 $ / /16 5/16 7/16 MI-CT120 $ / /8 1/4 3/4 MI-CT121 $ /8 1-1/ /4 3/16 3/8 1/2 MI-CT130 $ /4 1-1/ /4 3/16 3/8 5/8 MI-CT140 $42.00 Style CT INDEXALE DRILLS TURNING & ORING STYLE C SHANK TIP A C T W L 1/4 1/4 2 1/16 1/4 1/4 MI-C4 $ /16 5/16 2-1/4 3/32 5/16 3/8 MI-C5 $ /8 3/8 2-1/2 3/32 3/8 3/8 MI-C6 $ /16 7/16 3 3/32 7/16 1/2 MI-C7 $ /2 1/2 3-1/2 1/8 1/2 1/2 MI-C8 $ /8 5/8 4 5/32 5/8 5/8 MI-C10 $ /4 3/4 4-1/2 3/16 3/4 3/4 MI-C12 $30.90 Style C ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD STYLE D SHANK TIP A C T W L 1/4 1/4 2 1/16 1/4 5/16 MI-D4 $ /16 5/16 2-1/4 3/32 5/16 3/8 MI-D5 $ /8 3/8 2-1/2 3/32 3/8 1/2 MI-D6 $ /16 7/16 3 3/32 7/16 1/2 MI-D7 $ /2 1/2 3-1/2 1/8 1/2 1/2 MI-D8 $ /8 5/8 4 5/32 5/8 5/8 MI-D10 $ /4 3/4 4-1/2 3/16 3/4 3/4 MI-D12 $28.90 STYLE E Style ER & EL SHANK TIP Right Left A C F T W L Hand Hand 5/16 5/16 2-1/4 1/16 3/32 1/4 3/8 MI-ER5 MI-EL5 $ /8 3/8 2-1/2 1/16 3/32 1/4 3/8 MI-ER6 MI-EL6 $ /2 1/2 3-1/2 3/32 1/8 5/16 5/8 MI-ER8 MI-EL8 $ /8 5/8 4 3/32 1/8 5/16 5/8 MI-ER10 MI-EL10 $ /4 3/4 4-1/2 1/8 5/32 3/8 3/4 MI-ER12 MI-EL12 $26.50 Style D Master Catalog Style E SHANK TIP A C T W L 5/16 5/16 2-1/4 3/32 5/16 3/8 MI-E5 $ /8 3/8 2-1/2 3/32 3/8 1/2 MI-E6 $ /2 1/2 3-1/2 1/8 1/2 1/2 MI-E8 $ /8 5/8 4 5/32 5/8 5/8 MI-E10 $ /4 3/4 4-1/2 3/16 3/4 3/4 MI-E12 $27.65

147 CARIDE RADIUS TOOLS CONVEX & CONCAVE RADIUS TOOLS RXD Style RAD Style Full Line Available! Please call for more information. SHANK TIP RXD STYLE RAD STYLE A C T L R Right Left Right Left Hand Hand Hand Hand 1/32 MI-RXD1 MI-RXL1 MI-RAD1 MI-RAL1 $ /16 MI-RXD2 MI-RXL2 MI-RAD2 MI-RAL2 $ /32 MI-RXD3 MI-RXL3 MI-RAD3 MI-RAL3 $ /8 3/8 2-1/2 3/32 3/8 1/8 MI-RXD4 MI-RXL4 MI-RAD4 MI-RAL4 $ /32 MI-RXD5 MI-RXL5 MI-RAD5 MI-RAL5 $ /16 MI-RXD6 MI-RXL6 MI-RAD6 MI-RAL6 $ /32 MI-RXD7 MI-RXL7 MI-RAD7 MI-RAL7 $ /4 MI-RXD8 MI-RXL8 MI-RAD8 MI-RAL8 $ /32 MI-RXD9 MI-RXL9 MI-RAD9 MI-RAL9 $ /2 1/2 3-1/2 1/8 1/2 5/16 MI-RXD10 MI-RXL10 MI-RAD10 MI-RAL10 $ /32 MI-RXD11 MI-RXL11 MI-RAD11 MI-RAL11 $ /8 MI-RXD12 MI-RXL12 MI-RAD12 MI-RAL12 $ /32 MI-RXD13 MI-RXL13 MI-RAD13 MI-RAL13 $ /4 3/4 4-1/2 3/16 3/4 7/16 MI-RXD14 MI-RXL14 MI-RAD14 MI-RAL14 $ /32 MI-RXD15 MI-RXL15 MI-RAD15 MI-RAL15 $ /2 MI-RXD16 MI-RXL16 MI-RAD16 MI-RAL16 $45.85 Set of 4: 1/16, 1/8, 1/4, 3/8 radius MI-RXD21 MI-RXL21 MI-RAD21 MI-RAL21 $ *Set of 8: 1/32 to 1/4 radius in 1/32 increments MI-RXD22 MI-RXL22 MI-RAD22 MI-RAL22 $ Set of 8: 1/16 to 1/2 radius in 1/16 increments MI-RXD23 MI-RXL23 MI-RAD23 MI-RAL23 $ Set of 16: 1/32 to 1/2 radius in 1/32 increments MI-RXD24 MI-RXL24 MI-RAD24 MI-RAL24 $ SPLIT- END RADIUS TOOLS Micrograin carbide Full radius Relieved for right hand cut meter to finish ground Split Tolerance of tool center Split length in proportion to length of tool One End Split COMINATION THREAD & GROOVE TOOL Thread and groove with the same tool! Micrograin carbide Right hand cutting Please specify groove width when ordering Groove OD Thread ID Groove ID Thread OD Min. ore W 60 Offset Max. Depth VENTURE II GLASSES Two Ends Split One Split End Two Split Ends Split Length 1/8 1-1/2 3/8 MI-RSF1251 $18.85 MI-RSF1252 $ /16 2 3/8 MI-RSF1871 $22.70 MI-RSF1872 $ /4 2-1/2 3/8 MI-RSF2501 $26.15 MI-RSF2502 $ /16 2-1/2 1/2 MI-RSF3121 $38.70 MI-RSF3122 $ /8 2-1/2 1/2 MI-RSF3751 $49.90 MI-RSF3752 $ /2 3 5/8 MI-RSF5001 $73.65 MI-RSF5002 $91.35 Tool ID No. Max Depth Save Tool Change Time! Groove W Min ore Offset TG IT TG /32 max 1/ /4 2-1/2 IT TG IT TG IT TG /8 max 5/ /16 2-1/2 IT TG IT TG IT TG /32 max 3/ /8 2-1/2 IT TG IT base curved lens provides full side protection without distracting seams or traditional type side shields Nose buds secure the glass and prevent slipping while providing a pillow soft fit Temples adjust to four different lengths Lenses are coated for superior scratch resistance Lenses provide 99% protection against harmful UV rays Exceeds ANSI Z standards CE EN166 and CAN/CSA Z certified Frame Color $51.69 $64.68 $ Master Catalog 415 lack Lens Color Clear PYR-S1810S $4.39 Gray PYR-S1820S $4.99 lue PYR-S1860S $4.99 Amber PYR-S1830S $4.99 CARIDE INSERTS DEURRING

148 CHUCK JAWS LATHE WORKHOLDING SOLID CARIDE GROOVE TOOLS SOLID CARIDE GROOVE TOOLS MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Min. ore D1 N/C GENERATION meter to Minimum Hole Maximum Hole Depth Overall Length +1/64. D2 For retaining ring grooves Lockdown flat automatically locates tool on center Micrograin carbide Made in Full Line Available! Please call for more information. L1 Proj. P Tool Width W.250 1/4 2-1/ / /4 2-1/ / /4 2-1/ / /16 2-1/ / /16 2-1/ / /8 2-1/ / /8 2-1/ /.048 Max. Depth L2 1/4 MI-RR0174 3/8 MI-RR0176 1/2 MI-RR0178 5/8 MI-RR /4 MI-RR0254 3/8 MI-RR0256 1/2 MI-RR0258 5/8 MI-RR /4 MI-RR0304 3/8 MI-RR0306 1/2 MI-RR0308 5/8 MI-RR /4 MI-RR0334 3/8 MI-RR0336 1/2 MI-RR0338 3/4 MI-RR /4 MI-RR0384 3/8 MI-RR0386 1/2 MI-RR0388 3/4 MI-RR /4 MI-RR0394 3/8 MI-RR0396 1/2 MI-RR0398 3/4 MI-RR MI-RR /4 MI-RR /4 MI-RR0464 3/8 MI-RR0466 1/2 MI-RR0468 3/4 MI-RR MI-RR /4 MI-RR04620 $32.90 $32.90 $32.90 $41.05 $41.05 $53.50 $53.50 GROOVE TOOLS FOR O RING GROOVES N/C GENERATION meter to Minimum Hole Depth Overall Length ±1/ Master Catalog ore D1 D2 Min. ore D1 L /4 2-1/ /8 2-1/2. D2 L1 Proj. P Tool Width W Left-hand groove tools and other sizes also available. Full Line Available! Please call for more information. Max. Depth L2 1/4 MI-RR0554 3/8 MI-RR0556 1/2 MI-RR /8 2-1/ /.057 3/4 MI-RR MI-RR /4 MI-RR /4 MI-RR0624 3/8 MI-RR0626 1/2 MI-RR /8 2-1/ /.064 3/4 MI-RR MI-RR /4 MI-RR /4 MI-RR0694 3/8 MI-RR0696 1/2 MI-RR /8 2-1/ /.071 3/4 MI-RR MI-RR /4 MI-RR /4 MI-RR0874 3/8 MI-RR0876 1/2 MI-RR /8 2-1/ /.089 3/4 MI-RR MI-RR /4 MI-RR /2 MI-RR0938 3/4 MI-RR / / MI-RR /4 MI-RR /2 MI-RR /2 MI-RR1258 3/4 MI-RR / / MI-RR /4 MI-RR /2 MI-RR /2 MI-RR / /.158 3/4 MI-RR MI-RR /4 MI-RR / / /2 MI-RR /2 MI-RR1878 3/4 MI-RR / / MI-RR /4 MI-RR / /2 MI-RR /2 MI-RR / /4 MI-RR /2 MI-RR /4 MI-RR / MI-RR25016 Depth L2 Proj. P Radius R Width W 1/2.010/ /.098 MI-OR0968 9/ / /.143 MI-OR1419 5/8.035/ /.146 MI-OR /4.010/ /.176 MI-OR / / /.210 MI-OR /16.035/ /.243 MI-OR24115 $53.50 $53.50 $53.50 $53.50 $75.05 $75.05 $75.05 $75.05 $75.05 $75.05 $32.90 $54.05

149 SOLID CARIDE THREADING TOOLS 60 INTERNAL THREADING TOOLS RAZED THREAD MILLS N/C GENERATION meter to Minimum Hole Depth Overall Length ±1/64 Designed for milling precision I.D. and O.D. threads in all types of steels, non-ferrous metals and exotic materials. Equally effective in composites used in the aircraft industry. Thread form generated is American Standard thread. Minimum pitch listed is for an internal thread. Solid carbide head and shank for maximum rigidity. meter: to Cutter meter: : + 1/32 Cutter D1 D2 Flat F Len. L Thick T No. of Flutes Min. Pitch 3/8 1/ / MI-TM375 $ /2 5/ / MI-TM500 $ /4 3/ / MI-TM750 $ / MI-TM001 $ COMINATION ORE & THREAD TOOL ore and thread with the same tool! Micrograin carbide Right hand cutting Turn OD Thread OD Thread ID ore ID Min. ore 60 Offset Max. Depth Tool ID No. Min. Hole. D1 Full Line Available! Please call for more information.. D2 L1 Proj. P Offset Point Y.080 1/8 1-1/ /8 1-1/ / / / /4 2-1/ /4 2-1/ /16 2-1/ /16 2-1/ /8 2-1/ /8 2-1/ / Max Depth Thread Width Min ore Max. Hole Depth L2 Save a Tool Position! Right Hand Left Hand MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL MI-IT MI-ITL $ MI-IT MI-ITL Offset IT CM CM / /4 2 1/2 IT CM IT CM IT CM / /16 2 1/2 IT CM IT CM IT CM / /8 2 1/2 IT CM IT $46.17 $61.03 $ Master Catalog 417 CARIDE INSERTS DEURRING

150 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD KEYSEAT CUTTERS WOODRUFF KEYSEAT CUTTERS Type- HSS & M35 Cobalt KEO woodruff keyseat cutters are extremely versatile profile milling cutters. Although originally designed to mill standard woodruff keyseat, they satisfy a variety of applications from milling slots to milling threads. Available in straight and stagger tooth models. 1/2 Straight Amer. Std. # A HSS COALT of Teeth Head. Face Width Straight Tooth Stagger Tooth Straight Tooth Master Catalog Stagger Tooth 202 1/4 1/16 2-1/16 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /2 5/16 1/16 2-1/16 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /2 5/16 3/32 2-3/32 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /8 1/16 2-1/16 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /8 3/32 2-3/32 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /8 1/8 2-1/8 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /2 1/16 2-1/16 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /2 3/32 2-3/32 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /2 1/8 2-1/8 KEO $23.56 KEO $30.75 KEO $28.63 KEO $ /8 3/32 2-3/32 KEO $23.79 KEO $30.96 KEO $28.92 KEO $ /8 1/8 2-1/8 KEO $23.79 KEO $30.96 KEO $28.92 KEO $ /8 5/32 2-5/32 KEO $23.79 KEO $30.96 KEO $28.92 KEO $ /8 3/16 2-3/16 KEO $23.79 KEO $30.96 KEO $28.92 KEO $ /4 1/8 2-1/8 KEO $24.94 KEO $31.96 KEO $30.30 KEO $ /4 5/32 2-5/32 KEO $24.94 KEO $31.96 KEO $30.30 KEO $ /4 3/16 2-3/16 KEO $24.94 KEO $31.96 KEO $30.30 KEO $ /4 1/4 2-1/4 KEO $24.94 KEO $31.96 KEO $30.30 KEO $ /8 5/32 2-5/32 KEO $27.20 KEO $34.99 KEO $33.06 KEO $ /8 3/16 2-3/16 KEO $27.20 KEO $34.99 KEO $33.06 KEO $ /8 7/32 2-7/32 KEO $27.70 KEO $34.99 KEO $33.68 KEO $ /8 1/4 2-1/4 KEO $27.70 KEO $34.99 KEO $33.68 KEO $ /16 2-3/16 KEO $29.78 KEO $39.12 KEO $36.19 KEO $ /32 2-7/32 KEO $30.06 KEO $39.39 KEO $36.53 KEO $ /4 2-1/4 KEO $30.06 KEO $39.39 KEO $36.53 KEO $ /16 2-5/16 KEO $30.88 KEO $39.96 KEO $37.54 KEO $ /8 2-3/8 KEO $30.88 KEO $39.96 KEO $37.54 KEO $ /8 3/16 2-3/16 KEO $33.48 KEO $45.33 KEO $40.68 KEO $ /8 7/32 2-7/32 KEO $33.48 KEO $45.33 KEO $40.68 KEO $ /8 1/4 2-1/4 KEO $34.11 KEO $45.33 KEO $41.46 KEO $ /8 5/16 2-5/16 KEO $35.77 KEO $46.13 KEO $43.48 KEO $ /4 3/16 2-3/16 KEO $37.36 KEO $47.14 KEO $45.42 KEO $ /4 7/32 2-7/32 KEO $37.36 KEO $47.14 KEO $45.42 KEO $ /4 1/4 2-1/4 KEO $38.60 KEO $49.77 KEO $46.91 KEO $ /4 5/16 2-5/16 KEO $40.15 KEO $51.01 KEO $48.80 KEO $ /4 3/8 2-3/8 KEO $40.15 KEO $51.01 KEO $48.80 KEO $ /8 1/4 2-1/4 KEO $43.27 KEO $55.42 KEO $52.60 KEO $ /8 5/16 2-5/16 KEO $43.27 KEO $55.42 KEO $52.60 KEO $ /8 3/8 2-3/8 KEO $44.05 KEO $56.18 KEO $53.53 KEO $ /2 1/4 2-1/4 KEO $44.78 KEO $59.27 KEO $54.44 KEO $ /2 5/16 2-5/16 KEO $46.35 KEO $59.27 KEO $56.33 KEO $ /2 3/8 2-3/8 KEO $47.89 KEO $62.42 KEO $58.20 KEO $ WOODRUFF KEYSEAT CUTTER SETS Type- HSS & M35 Cobalt NEW ITEM! NEW ITEM! Straight Stagger Teeth Type # of Pieces Includes Straight 10 43,204,404,305,505,406, KEO $ Staggered ,806,608,808 KEO $ Straight 41 1 of All American KEO $1, Staggered 41 Std Sizes KEO $1,747.47

151 KEYSEAT CUTTERS WOODRUFF NARROW WIDTH KEYSEAT CUTTERS Type- HSS & M35 Cobalt Fractional widths 1/2 diameter straight shank 2 overall length Right hand cut Made in the Head. A Head Width SOLID CARIDE KEY CUTTERS Double End, 3 Flute Solid Micrograin Carbide Head. A Head Width Head. A Head Width 1/4 1/64 KEO $ /8 5/64 KEO $ /4 9/64 KEO $ / KEO $ /8 3/32 KEO $ /4 5/32 KEO $ /4 1/32 KEO $ /8 7/64 KEO $ /4 11/64 KEO $ /4 3/64 KEO $ /8 1/8 KEO $ /8 3/64 KEO $ /16 1/64 KEO $ /8 9/64 KEO $ /8 1/16 KEO $ / KEO $ /32 KEO $ /8 5/64 KEO $ /16 1/32 KEO $ /64 KEO $ /8 3/32 KEO $ /16 3/64 KEO $ /16 KEO $ /8 7/64 KEO $ /8 1/64 KEO $ /64 KEO $ /8 1/8 KEO $ / KEO $ /32 KEO $ /8 9/64 KEO $ /8 1/32 KEO $ /64 KEO $ /8 5/32 KEO $ /8 3/64 KEO $ /8 KEO $ /8 11/64 KEO $ /2 1/64 KEO $ /64 KEO $ /8 3/16 KEO $ / KEO $ /32 KEO $ /8 13/64 KEO $ /2 1/32 KEO $ /64 KEO $ /8 7/32 KEO $ /2 3/64 KEO $ /8 3/64 KEO $ /2 3/64 KEO $ / KEO $ /8 1/16 KEO $ /2 1/16 KEO $ /8 1/32 KEO $ /8 5/64 KEO $ /2 5/64 KEO $ /8 3/64 KEO $ /8 3/32 KEO $ /2 3/32 KEO $ /8 1/16 KEO $ /8 7/64 KEO $ /2 7/64 KEO $ /8 5/64 KEO $ /8 1/8 KEO $ /2 1/8 KEO $ /4 1/32 KEO $ /8 9/64 KEO $ /2 9/64 KEO $ /4 3/64 KEO $ /8 5/32 KEO $ /2 5/32 KEO $ /4 1/16 KEO $ /8 11/64 KEO $ /2 11/64 KEO $ /4 5/64 KEO $ /4 3/64 KEO $ /2 3/16 KEO $ /4 3/32 KEO $ /4 1/16 KEO $ /2 13/64 KEO $ /4 7/64 KEO $ /4 5/64 KEO $ /2 7/32 KEO $ /8 1/32 KEO $ /4 3/32 KEO $ /2 15/64 KEO $ /8 3/64 KEO $ /4 7/64 KEO $ /8 1/16 KEO $ /4 1/8 KEO $51.53 NEW ITEM! CARIDE INSERTS Cutter Neck Neck Length No. Of Teeth 1/ / / / /2 1/ / /2 5/ / /2 Cutter Width IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT IT $39.02 $43.49 $43.49 $43.49 Cutter Neck Neck Length No. Of Teeth Master Catalog 419 5/ / /2 3/ / /2 1/ / Cutter Width IT IT IT IT $ IT IT IT IT $ IT IT $ IT IT IT $ IT $ IT $ IT $ IT $ IT $ IT $ IT $ IT $ IT $ IT $57.90 DEURRING

152 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS DOVETAIL & T-SLOT CUTTERS T-SLOT MILLING CUTTERS Type- HSS & M35 Cobalt KEO T-slot milling cutters have staggered teeth on the circumferential surface and teeth on both sides. The side teeth alternate to provide maximum chip clearance and stability to permit rapid milling of T-slots with lower risk of breakage. DOVETAIL CUTTERS Type- HSS & M35 Cobalt Ideal tool for milling dovetails Available in 45 and 60 angles HSS or Cobalt Made in the A olt Size A C D E F Head. Head Width Neck.. Length 1/4 9/16 15/64 17/64 1/2 2-19/ /32 KEO $ /16 21/32 17/64 21/64 1/2 2-11/ /32 KEO $ /8 25/32 21/64 13/32 3/4 3-1/4 2-1/32 KEO $ /2 31/32 25/64 17/32 3/4 3-7/16 2-1/32 KEO $ /8 1-1/4 31/64 21/ /16 2-9/32 KEO $ /4 1-15/32 5/8 25/ /16 2-9/32 KEO $ /32 53/64 1-1/32 1-1/4 4-13/16 2-9/32 KEO $ /4 2-7/32 1-3/32 1-7/32 1-1/4 5-3/8 2-9/32 KEO $ /2 2-21/ / /32 1-1/4 5-29/32 2-9/32 KEO $ Cutter Width HSS COALT NEW ITEM! NEW ITEM! C D 45 Angle 60 Angle 45 Angle 60 Angle 3/8 1/8 3/16 3/8 2-1/8 KEO KEO $44.52 KEO KEO $ /2 1/8 7/32 3/8 2-1/8 KEO KEO $48.20 KEO KEO $ /4 3/16 5/16 3/8 2-1/8 KEO KEO $56.37 KEO KEO $ /4 7/16 1/2 2-1/2 KEO KEO $69.79 KEO KEO $ /8 3/8 9/16 5/8 2-7/8 KEO KEO $87.99 KEO KEO $ /8 1/2 13/16 7/8 3-1/4 KEO KEO $ KEO KEO $ /4 11/16 1-1/ /4 KEO KEO $ KEO KEO $ /2 3/4 1-1/ /4 KEO KEO $ KEO KEO $ INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD DOVETAIL CUTTERS Carbide Head on Hardened Steel Head : +.000/ Head Head Head Width of Cut Width of Cut Width of Cut DOVETAIL CUTTER WITH STEEL SHANK Master Catalog Head Width of Cut Neck Tool ID # No. Of Teeth 3/ DH /2 5 Neck Length Included Angle IT $ / DH / /8 1/4 60 IT $ / DH /2 5 IT $ / DH /2 4 IT $ / DH / /8 1/4 90 IT $ / DH /2 5 IT $ DOVETAIL CUTTERS Head Width of Cut Neck Tool ID # No. Of Teeth Neck Length 3/ DS / /2 1/4 IT $ / DS / /2 1/4 IT $ / DS / /2 1/4 IT $ / DS / /2 1/4 IT $ / DS / /4 IT $ / DS / /2 1/4 IT $ DOVETAIL CUTTERS Head Width of Cut Neck Tool ID # No. Of Teeth Neck Length 3/ DS / /2 1/4 IT $ / DS / /2 1/4 IT $ / DS / /2 1/4 IT $ / DS / /2 1 /4 IT $ / DS / /4 IT $ / DS / /2 1/4 IT $86.31

153 SIDE MILLING CUTTERS STRAIGHT TOOTH SIDE MILLING CUTTERS High speed steel Plain teeth Staggered tooth side milling cutters also available. NEW ITEM! Hole Size of Teeth Full Line Available! Please call for more information. Width of Face Depth of Cut Staggered Tooth Side Milling Cutters Also Available! Please Call For More Information! Hole Size of Teeth Width of Face Depth of Cut 2 1/2 14 3/ I $ / /2.962 I $ /2 14 1/4.527 I $ / /8.962 I $ /2 14 3/8.527 I $ /2 1-1/4 20 1/2.805 I $ /8 14 3/ I $ / I $ /8 14 1/4.488 I $ / I $ /8 14 5/ I $ / I $ /8 14 3/8.488 I $ / I $ /8 14 1/4.370 I $ / I $ /8 14 5/ I $ / I $ /8 14 3/8.370 I $ / I $ /8 14 7/ I $ / I $ /2 7/8 16 3/ I $ / I $ /2 7/8 16 1/4.581 I $ / I $ /2 7/8 16 5/ I $ / I $ /2 7/8 16 3/8.581 I $ / I $ /2 7/8 16 7/ I $ / I $ /2 7/8 16 1/2.581 I $ / I $ / / I $ / I $ / /4.502 I $ / I $ / / I $ I $ / /8.502 I $ / I $ / / I $ /4 22 3/ I $ / /2.502 I $ /4 22 7/ I $ / /8.502 I $ /4 22 1/ I $ / I $ /4 22 5/ I $ / I $ / / I $ /4.712 I $ /4 22 3/ I $ / I $ /4 22 7/ I $ / I $ /4 22 1/ I $ / I $ /4 22 9/ I $ /8.712 I $ /4 22 5/ I $ / I $ / / I $ / I $ /4 22 3/ I $ /2.712 I $ /4 22 7/ I $ / I $ / I $ /8.712 I $ / / I $ / I $ / / I $ /4.712 I $ /2 1-1/4 24 3/ I $ / I $ /2 1-1/4 24 1/ I $ /8.712 I $ / I $ I $ / I $ /4 18 3/ I $ / I $ /4 18 1/4.633 I $ / I $ /4 18 5/ I $ / I $ /4 18 3/8.633 I $ / I $ /4 18 1/2.633 I $ / I $ /4 18 3/4.633 I $ / I $ / / I $ / I $ / /4.962 I $ / I $ / / I $ /4 24 1/ I $ / /8.962 I $ /4 24 9/ I $ Master Catalog 421 CARIDE INSERTS DEURRING

154 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS MILLING CUTTERS CONVEX & CONCAVE MILLING CUTTERS High Speed Steel, Type Full Line Available! Please call for more information. Radius Cutter Concave Type No.of Flutes Cutter Convex type No.of Flutes 1/32 1/2 3 3/4 6 I $ /4 6 I $ /16 1/2 3 3/4 6 I $ /4 6 I $ /32 1/2 3 3/4 6 I $ /8 6 I $ /8 3/4 3-1/2 1 6 I $ /2 1-1/4 6 I $ /32 3/4 3-1/2 1 6 I $ /2 1-5/16 6 I $ /16 3/4 3-1/2 1 6 I $ /2 1-3/8 6 I $ /4 3/ /4 4 I $ /2 6 I $ /16 3/ /4 4 I $ /8 6 I $ /8 3/4 4-3/16 1-1/2 4 I $ /4 6 I $ SINGLE ANGLE CHAMFERING CUTTERS High Speed Steel, RH Cut, Type NEW ITEM! NEW ITEM! DOULE ANGLE MILLING CUTTERS High Speed Steel, RH Cut, Type NEW ITEM! TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Cutter Width Angle 1/2 1/8 3/8 2-1/8 45 I $ /4 3/16 3/8 2-1/8 45 I $ /16 1/2 2-1/2 45 I $ /2 1/2 3/4 2-3/4 45 I $ /2 7/32 3/8 2-1/8 60 I $ /4 5/16 3/8 2-1/8 60 I $ /16 1/2 2-1/2 60 I $ /2 5/8 3/4 2-3/4 60 I $59.91 SLITTING SAW STU MILL ARORS With R8 Made of Alloy Forged Steel for long durable service life Hardened to RC and ground to ensure maximum accuracy Face is held perpendicular to center line within " Pilot diameter is sized for precision fit with cutter and is keyed for positive drive Heavy duty locking LH nut and set of arbor spacers are included Draw ar Thread 7/16" x 20 VENTURE II SAFETY GLASSES Included Angle Cutter Master Catalog Cutter Thickness 60 3/4 3/8 2-3/8 3/16 I $ /2 2-27/32 5/16 I $ /8 5/8 3-7/32 7/16 I $ /2 5/8 3-3/8 1/2 I $ /8 3/4 3-25/32 5/8 I $ /4 3/8 2-7/16 1/4 I $ /2 2-29/32 3/8 I $ /8 5/8 3-9/32 1/2 I $ /2 5/8 3-7/16 9/16 I $ /8 3/4 3-25/32 5/8 I $ Arbor Arbor Wrench D L Type Size S R I $ R-8 1-1/ I $ base curved lens provides full side protection without distracting seams or traditional type side shields Nose buds secure the glass and prevent slipping while providing a pillow soft fit Temples adjust to four different lengths Lenses are coated for superior scratch resistance Lenses provide 99% protection against harmful UV rays Exceeds ANSI Z standards CE EN166 and CAN/CSA Z certified Frame Color lack Lens Color Clear PYR-S1810S $4.39 Gray PYR-S1820S $4.99 lue PYR-S1860S $4.99 Amber PYR-S1830S $4.99

155 SLITTING SAWS PLAIN METAL SLITTING SAWS For General Slotting Or Cut-off Operations 10 degree positive rake angle on all blades Available with flat and parallel hubs for gang slitting as a Special Order. Available in variety of tooth modifications. Closer dimensional tolerances also available-please call for more information Cutting 1-1/4 1-1/2 1-3/ /2 3 Face Width Arbor Hole No. Teeth 1/32 1/2 28 TU-I-010 $6.72 1/16 1/2 28 TU-I-011 $7.09 1/32 1/2 32 TU-I-012 $7.72 1/16 1/2 26 TU-I-013 $8.03 3/32 1/2 26 TU-I-014 $8.93 1/8 1/2 26 TU-I-015 $ /32 1/2 34 TU-I-016 $9.45 1/16 1/2 30 TU-I-017 $9.66 3/32 1/2 30 TU-I-018 $ /8 1/2 30 TU-I-019 $ /32 1/2 38 TU-I-020 $9.61 1/16 1/2 34 TU-I-021 $9.92 3/32 1/2 34 TU-I-022 $ /8 1/2 34 TU-I-023 $ /32 1/2 34 TU-I-024 $ /16 1/2 34 TU-I-024A $ /32 7/8 28 TU-I-025 $ /64 7/8 28 TU-I-026 $ /16 7/8 28 TU-I-027 $ /32 7/8 28 TU-I-028 $ /8 7/8 28 TU-I-029 $ /16 7/8 28 TU-I-030 $ / TU-I-031 $ / TU-I-032 $ / TU-I-033 $ / TU-I-034 $17.12 Cutting SAW ARORS STANDARD PRECISION For Slitting / Sawing Applications GOLD SERIES For Grinding/ Slitting/ Sawing Applications Face Width Arbor Hole No. Teeth 1/ TU-I-035 $ / TU-I-036 $ / TU-I-036A $ / TU-I-037 $ / TU-I-038 $ / TU-I-039 $ / TU-I-040 $ / TU-I-041 $ / TU-I-042 $ / TU-I-043 $ / TU-I-044 $ / TU-I-045 $ / TU-I-046 $ /8 1-1/4 40 TU-I-047 $ / TU-I-049 $ / TU-I-050 $ / TU-I-051 $ / TU-I-052 $ / TU-I-053 $ /8 1-1/4 42 TU-I-054 $ / TU-I-055 $ /16 1-1/4 42 TU-I-055A $ / TU-I-062 $ /8 1-1/4 46 TU-I-063 $ /16 1-1/4 46 TU-I-064 $ METAL SLITTING SAWS SIDE CHIP CLEARANCE Designed for deep cuts or slots where side cutting chip clearance is a factor Free cutting blades do not bind in deep cutting. For deep slotting applications, supplied with ground recess between bottom of side tooth and hub. 10 degree positive rake angle standard Cutting 2-1/ Face Width uy The Set & Save!!! Arbor Hole No. Teeth 1/16 7/8 26 TU-I-074 $ /32 7/8 26 TU-I-075 $ /8 7/8 26 TU-I-076 $ /16 7/8 26 TU-I-076A $ / TU-I-077 $ / TU-I-078 $ / TU-I-079 $ / TU-I-080 $ / TU-I-080A $ / TU-I-081 $ / TU-I-082 $ / TU-I-083 $ / TU-I-084 $ / TU-I-085 $ / TU-I-086 $ / TU-I-087 $ / TU-I-088 $ /8 1-1/4 38 TU-I-089 $ / TU-I-090 $ / TU-I-091 $ / TU-I-092 $ / TU-I-093 $ / TU-I-094 $ /8 1-1/4 40 TU-I-095 $ / TU-I-096 $ /16 1-1/4 40 TU-I-097 $ CARIDE INSERTS Standard Precision Features: General purpose arbor Vibra-core Design Lowest Profile Caps Accurate general purpose arbor Hardened and ground Deep sleeve design gives extra support and less cutter slippage Low profile caps and longer reaches Weldon shanks Wooden stand Gold Series Features: Ultra precision arbor Engineered for carbide cutters Higher RPM'S & accuracy Vibra-core* design Deep low profile caps gives extra support and less vibration Heat treated and ground to.0004 concentricity and square Arbor Sets Set of 3 G.P..250,.375,.500 SIE-SA-3S $ G.P..625,1.000,1.250 SIE-SA-3L $ Gold.250,.375,.500 SIE-GSSA-3S $ Gold.625,1.000,1.250 SIE-GSSA-3L $ F A C D E Standard Precision Arbors Gold Series Arbors SIE-SA-250 $36.97 SIE-GSSA-250 $ SIE-SA-375 $38.74 SIE-GSSA-375 $ SIE-SA-500 $41.22 SIE-GSSA-500 $ SIE-SA-625 $44.96 SIE-GSSA-625 $ SIE-SA-1000 $52.26 SIE-GSSA-1000 $ SIE-SA-1250 $52.88 SIE-GSSA-1250 $ Master Catalog 423 DEURRING

156 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS SLITTING SAWS CUTTING SAWS Designed for cutting aluminium, brass, soft metals, and plastic in form of tubing, sheets and nlight extruded rods, bars and shapes. FEATURES: High speed steel and hardened ground. Side ground with clearance to hole. Teeth ground on face- designed for soft materials. Plus ground up sharp with no land on top. Cutting Thick Arbor Hole No. Teeth Speed RPM 7 & 8 Saws Also Available! Other Sizes And Dimensions Not Listed Are Special - d On Request. SLITTING & SLOTTING SAW ARORS R8, straight shank (SS) or weldon straight shank (WS) Spring loaded lades are firmly secured in position with a hex screw / TU-I / TU-I / TU-I / TU-I / TU-I TU-I / TU-I TU-I / TU-I TU-I / TU-I-293A TU-I-293A / TU-I TU-I / TU-I TU-I / TU-I TU-I / TU-I-296A TU-I-296A / TU-I TU-I / TU-I TU-I / TU-I TU-I / TU-I-299A TU-I-299A / TU-I TU-I / TU-I / TU-I TU-I / TU-I / TU-I TU-I / TU-I / TU-I-302A TU-I-302A / TU-I-302A STANDARD SCREW SLOTTING SAW Designed For Shallow Slotting Cuts FEATURES: Not recommended for deep cuts. Teeth ground - not milled to ensure blades run true-concentric. Concave ground sides insure proper side relief. Available with any number of teeth - special order. Closer dimensional tolerances and tooth modifications available. Cutting 2-3/4 2-3/4 2-3/4 2-3/4 2-3/4 2-3/4 Face Width Arbor Hole No. Teeth TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J NEW ITEM! Straight Cutting 2-3/4 2-1/4 2-1/4 1-3/4 1-3/4 Face Width Arbor Hole No. Teeth TU-J TU-J TU-J TU-J TU-J TU-J TU-J TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 60 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J /8 90 TU-J MRO & SAFETY FLAT STOCK/DRILL ROD Weldon R Master Catalog Arbor Hole Length Type Size 1/2 SS 3-3/4 3/8 I $ /2 WS 2-9/16 1/2, 5/8, 3/4, 7/8, 1 I $31.18 R-8 5-3/32 1/2, 5/8, 3/4, 7/8, 1 I $45.66

157 SLOTTING SAWS JEWELER S SLOTTING SAWS No. of Teeth 3/8" Arbor Hole 1/2" Arbor Hole NEW ITEM! HSS Used in slotting, sheeting and tubing For cutting thin tubing, wire and similar items, as well as for slotting very thin materials ANSI/ASME Tolerances: OD: Width: Hole : Additional sizes available I $6.79 I $ I $5.25 I $ I $5.25 I $ I $4.83 I $ I $4.63 I $ I $4.15 I $ I $4.15 I $ I $3.78 I $ I $3.78 I $ I $4.63 I $ I $4.63 I $ / I $8.02 I $ / I $7.33 I $ / I $5.90 I $ / I $5.70 I $ / I $5.25 I $ / I $5.25 I $ / I $4.83 I $ / I $ / I $ / I $4.83 I $ / I $4.83 I $ / I $9.90 I $ / I $9.56 I $ / I $6.79 I $ / I $6.29 I $ / I $5.90 I $ / I $5.70 I $ / I $5.25 I $ / I $5.25 I $ / I $5.25 I $ / I $5.99 I $ / I $ / I $9.90 I $ / I $9.72 I $ / I $7.03 I $ / I $ / I $6.29 I $ / I $5.90 I $ / I $5.25 I $ / I $5.70 I $ I $12.28 I $ I $11.88 I $ I $11.09 I $ I $8.71 I $ I $8.07 I $ I $7.23 I $ I $6.79 I $ I $6.29 I $ I $6.79 I $ I $6.79 I $6.79 No. of Teeth 3/8" Arbor Hole 1/2" Arbor Hole I $6.79 I $ I $6.79 I $ I $ I $7.23 I $ I $7.23 I $ I $8.07 I $ I $8.07 I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $9.76 Thickness Thickness Thickness No. of Teeth 1/2" Arbor Hole 1" Arbor Hole I $17.13 I $ I $15.25 I $ I $15.25 I $ I $13.07 I $ I $11.58 I $ I $9.60 I $ I $8.71 I $ I $8.71 I $ I $9.76 I $ I $9.76 I $ I $10.79 I $ I $10.79 I $ I $10.79 I $ I $11.48 I $ I $11.48 I $ I $21.29 I $ I $20.89 I $ I $19.80 I $ I $15.84 I $ I $14.55 I $ I $14.55 I $ I $15.84 I $ I $16.43 I $ I $16.43 I $ I $18.22 I $ I $18.61 I $ I $18.61 I $ I $26.53 I $ I $26.53 I $ I $22.37 I $ I $22.37 I $ I $22.37 I $ I $25.15 I $ I $25.15 I $ I $25.94 I $ I $25.94 I $25.94 Additional meters & Arbor Hole Combinations Available. Please Call For More Information Master Catalog 425 CARIDE INSERTS DEURRING

158 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID CARIDE SAWS SOLID CARIDE SAWS APPLICATION GUIDELINES If depth of cut exceeds 3 times saw thickness double standard concavity is recommended. If depth of cut exceeds 5 times saw thickness alternate tooth chamfer is recommended. Saw diameter concentricity should be within.001 when assembled on arbor. When using more than one saw at a time, a flat and parallel hub should be used to ensure proper spacing. If steel flanges are used, select the largest diameter possible. Keyways (generally not used with solid carbide slitting saws) also available. CUSTOM CARIDE SAWS Please call for special orders. Special Cutting meters Special Thicknesses Special Arbor Hole Sizes and Keyways Special Chamfers, Angles or Radii Special Tooth Configurations/Pitches PRICING FOR SPECIAL DECIMAL THICKNESSES Find the price of the closest thicker standard saw To this, add $5.00 for one of a size Add $3.50 for two to six of a size For 7 or more, there is no additional charge above the base price Quantity discounts apply to special thicknesses Saws made for gangs with special tolerances are priced on application SAW ARORS TOLERANCES DØ / D1Ø - +/-.003 dø / L - +/-.060 d1ø / L / L / Total thickness of saws/ spacers should not exceed 50% of L1 dimension. Arbor caps with longer L1dimension available. 3/4" dia 1/4" Hole 10 or 20 teeth 1" dia 3/8" Hole 12 or 24 Teeth Master Catalog DØ d1ø 1 1/4" dia 1/2" Hole 16 or 36 teeth 1 1/2" dia 1/2" Hole 16 or 36 teeth dø D1Ø L1 L L2 1 3/4" dia 1/2", 5/8" or 7/8" Hole 24 or 36 teeth Thickness.0020 RO-C07002 $ RO-C10002 $ RO-C12002 $ RO-C15002 $ RO-C17002 $ RO-C07004 $ RO-C10004 $ RO-C12004 $ RO-C15004 $ RO-C17004 $ RO-C07006 $90.80 RO-C10006 $75.80 RO-C12006 $98.30 RO-C15006 $ RO-C17006 $ RO-C07008 $60.60 RO-C10008 $68.00 RO-C12008 $79.25 RO-C15008 $90.50 RO-C17008 $ RO-C07010 $52.55 RO-C10010 $68.00 RO-C12010 $79.25 RO-C15010 $90.50 RO-C17010 $ RO-C07012 $51.65 RO-C10012 $53.40 RO-C12012 $61.10 RO-C15012 $77.85 RO-C17012 $ RO-C07014 $40.80 RO-C10014 $53.40 RO-C12014 $61.10 RO-C15014 $77.85 RO-C17014 $ RO-C07016 $40.80 RO-C10016 $53.40 RO-C12016 $61.10 RO-C15016 $77.85 RO-C17016 $ RO-C07018 $40.80 RO-C10018 $53.40 RO-C12018 $61.10 RO-C15018 $77.85 RO-C17018 $ RO-C07020 $40.80 RO-C10020 $45.20 RO-C12020 $54.00 RO-C15020 $63.55 RO-C17020 $ RO-C07023 $35.55 RO-C10023 $45.20 RO-C12023 $54.00 RO-C15023 $63.55 RO-C17023 $ RO-C07025 $35.55 RO-C10025 $45.20 RO-C12025 $54.00 RO-C15025 $63.55 RO-C17025 $ RO-C07028 $35.55 RO-C10028 $45.20 RO-C12028 $54.00 RO-C15028 $63.55 RO-C17028 $ RO-C07032 $29.65 RO-C10032 $41.45 RO-C12032 $41.90 RO-C15032 $55.55 RO-C17032 $ RO-C07035 $29.65 RO-C10035 $41.45 RO-C12035 $41.90 RO-C15035 $55.55 RO-C17035 $ RO-C07040 $29.65 RO-C10040 $41.45 RO-C12040 $41.90 RO-C15040 $55.55 RO-C17040 $ RO-C07045 $35.60 RO-C10045 $45.05 RO-C12045 $45.35 RO-C15045 $57.60 RO-C17045 $ RO-C07051 $35.60 RO-C10051 $45.05 RO-C12051 $45.35 RO-C15051 $57.60 RO-C17051 $ RO-C07062 $35.60 RO-C10062 $45.05 RO-C12062 $45.35 RO-C15062 $57.60 RO-C17062 $ RO-C07078 $46.35 RO-C10078 $56.75 RO-C12078 $55.50 RO-C15078 $69.80 RO-C17078 $ RO-C07092 $51.50 RO-C10092 $62.95 RO-C12092 $67.65 RO-C15092 $79.45 RO-C17092 $ RO-C07125 $67.35 RO-C10125 $84.15 RO-C12125 $86.70 RO-C15125 $89.00 RO-C17125 $ RO-C07156 $90.50 RO-C10156 $ RO-C12156 $ RO-C15156 $ RO-C17156 $ RO-C07187 $95.90 RO-C10187 $ RO-C12187 $ RO-C15187 $ RO-C17187 $ RO-C07250 $ RO-C10250 $ RO-C12250 $ RO-C15250 $ RO-C17250 $ " dia 1/2" or 1" Hole 24 or 48 teeth 2 1/4" dia 5/8" Hole 28 or 56 teeth 2 1/2" dia 1" Hole 28 or 56 teeth 2 3/4" dia 1" Hole 30 or 60 teeth 3" dia 1" Hole 30 or 60 Teeth Thickness.0020 RO-C20002 $ RO-C22002 $ RO-C25002 $ RO-C27002 $ RO-C30002 $ RO-C20004 $ RO-C22004 $ RO-C25004 $ RO-C27004 $ RO-C30004 $ RO-C20006 $ RO-C22006 $ RO-C25006 $ RO-C27006 $ RO-C30006 $ RO-C20008 $ RO-C22008 $ RO-C25008 $ RO-C27008 $ RO-C30008 $ RO-C20010 $ RO-C22010 $ RO-C25010 $ RO-C27010 $ RO-C30010 $ RO-C20012 $96.10 RO-C22012 $ RO-C25012 $ RO-C27012 $ RO-C30012 $ RO-C20014 $96.10 RO-C22014 $ RO-C25014 $ RO-C27014 $ RO-C30014 $ RO-C20016 $96.10 RO-C22016 $ RO-C25016 $ RO-C27016 $ RO-C30016 $ RO-C20018 $96.10 RO-C22018 $ RO-C25018 $ RO-C27018 $ RO-C30018 $ RO-C20020 $88.15 RO-C22020 $95.80 RO-C25020 $ RO-C27020 $ RO-C30020 $ RO-C20023 $88.15 RO-C22023 $95.80 RO-C25023 $ RO-C27023 $ RO-C30023 $ RO-C20025 $88.15 RO-C22025 $95.80 RO-C25025 $ RO-C27025 $ RO-C30025 $ RO-C20028 $88.15 RO-C22028 $95.80 RO-C25028 $ RO-C27028 $ RO-C30028 $ RO-C20032 $76.90 RO-C22032 $88.45 RO-C25032 $ RO-C27032 $ RO-C30032 $ RO-C20035 $76.90 RO-C22035 $88.45 RO-C25035 $ RO-C27035 $ RO-C30035 $ RO-C20040 $76.90 RO-C22040 $88.45 RO-C25040 $ RO-C27040 $ RO-C30040 $ RO-C20045 $79.35 RO-C22045 $93.20 RO-C25045 $ RO-C27045 $ RO-C30045 $ RO-C20051 $79.35 RO-C22051 $93.20 RO-C25051 $ RO-C27051 $ RO-C30051 $ RO-C20062 $79.35 RO-C22062 $93.20 RO-C25062 $ RO-C27062 $ RO-C30062 $ RO-C20078 $89.80 RO-C22078 $ RO-C25078 $ RO-C27078 $ RO-C30078 $ RO-C20092 $96.75 RO-C22092 $ RO-C25092 $ RO-C27092 $ RO-C30092 $ RO-C20125 $ RO-C22125 $ RO-C25125 $ RO-C27125 $ RO-C30125 $ RO-C20156 $ RO-C22156 $ RO-C25156 $ RO-C27156 $ RO-C30156 $ RO-C20187 $ RO-C22187 $ RO-C25187 $ RO-C27187 $ RO-C30187 $ RO-C20250 $ RO-C22250 $ RO-C25250 $ RO-C27250 $ RO-C30250 $ C Set 1/4 1/2 1/2 3/8 2-7/8 3/16 RO-A250 $ /8 1/2 5/8 3/8 2-7/8 1/4 RO-A375 $ /2 1/2 3/4 1/2 2-7/8 3/16 RO-A500 $ /8 3/4 1 7/8 4 1/4 RO-A625 $ /8 3/4 1-1/ /4 RO-A875 $ /4 1-1/ /4 RO-A1000 $ / /4 1-3/8 5 1/4 RO-A1250 $392.90

159 ANDSAW LADES-WELDED TO LENGTH Starrett bandsaw blades aim to satisfy your diverse metal-cutting needs with four qualities which will overcome the common-place as well as the more unusual industrial applications and at the same time reduce operating costs. You can count on Starrett blades to provide accurate cutting tools of the highest quality! C Tooth Types: Regular= General purpose for cutting and contouring a majority of ferrous and nonferrous metals Hook= 10 positive rake for fast cutting and reduced feed rates. For cutting nonferrous and tough alloys 3 and larger Variant= Gullets and tooth size vary over set intervals, with each tooth achieving a slightly different cutting angle. For interrupted cutting and high production cutting of solids Did You Know...? Coolant is the key to saw blade life. The number one reason that band saws break is coolant. Whether it is bad coolant, no coolant or coolant mixed wrong, coolant is essential in sawing, as there is much less room for the chip compared to milling. Without proper cutting fluid the chip may become welded to the tooth of the blade, resulting in an unbalanced blade and crooked cut. In addition, the chip may wedge in the cut, again resulting in a crooked cut and dull blade. POWERAND M42 i-metal High Speed Steel WELDED-TO-LENGTH ANDSAW LADES Ideal for general purpose cutting operations across a wide range of metals This bi-metal material has a high speed steel cutting edge (contains 8% cobalt) welded to an alloy steel back. Resists heat, abrasion and shock which allows faster cutting rates over a wide range of materials. Can be used on horizontal machines and light-duty vertical machines equally well. Ideal for contour cutting and general purpose cutting Length Width TPI 7ft. 9 3/ /S SR-PM $ ft /S SR-PM $ ft. 5 3/ /S SR-PM $ ft. 5 3/ /S SR-PM $ ft. 10-1/2 3/ /S SR-PM $ ft. 10-1/ /S SR-PM $ ft. 10-1/ /S SR-PM $ ft. 3/ /S SR-PM $ ft. 3/ /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft. 5 3/ /S SR-PM $ ft /S SR-PM $ ft. 6 3/ /S SR-PM $ ft. 6 3/ /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft / /S SR-PM $ ft / /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft. 1-1/ /S SR-PM $ ft. 1-1/ /S SR-PM $ ft. 1-1/ /S SR-PM $91.35 WELDED TO LENGTH! Tooth Set: P= Positive Rake-For cutting of solids S= Straight (0 ) Rake-For all material shapes W= Wavy Set (0 Rake)-Light duty for tubing, pipe and light duty sawing applications Length Width Thickness Thickness Master Catalog 427 TPI 12ft /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft / /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft / /S SR-PM $ ft / /S SR-PM $ ft / /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft /S SR-PM $ ft / /S SR-PM $ ft / /S SR-PM $ ft. 8 3/ /S SR-PM $ ft. 8 3/ /S SR-PM $ ft. 1-1/ /S SR-PM $ ft. 1-1/ /S SR-PM $ ft. 1-1/ /S SR-PM $ ft /S SR-PM $ ft / /S SR-PM $ ft / /S SR-PM $ ft / /S SR-PM $ ft /4 " /S SR-PM $ ft /4 " /S SR-PM $ ft /4 " /S SR-PM $ CARIDE INSERTS DEURRING

160 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ANDSAW LADES-WELDED TO LENGTH Duratec F (formerly Flex-ack ) Carbon Steel With A Flexible ack WELDED-TO-LENGTH ANDSAW LADES Ideal For Economical Cutting On Easy-to-Machine Ferrous Or Nonferrous Metal And Wood Flexible carbon steel back Economical general purpose cutting Ideal for both contour and straight cutting For nonferrous and low alloy metals, wood and plastics Length Width Tooth Shape TPI Length Master Catalog Width Thickness Thickness Tooth Shape TPI 5ft 1/2" Regular 10/S SR-HEF $ ft. 1/4" Regular 14/S SR-HEF $ ft 1/2" Regular 14/S SR-HEF $ ft. 1/2" Regular 10/S SR-HEF $ ft 1/2" Wavy 14/W SR-HEF $ ft. 1/2" Regular 14/S SR-HEF $ ft 1/2" Regular 18/W SR-HEF $ ft. 3/4" Regular 10/S SR-HEF $ ft 1/2" Regular 6/S SR-HEF $ ft. 3/4" Regular 14/S SR-HEF $ ft. 4-1/2 1/2" Regular 10/S SR-HEF $ ft. 5 3/4" Regular 6/S SR-HEF $ ft. 4-1/2 1/2" Regular 14/S SR-HEF $ ft. 5 3/4" Regular 8/S SR-HEF $ ft. 4-1/2 1/2" Wavy 14/W SR-HEF $ ft. 5 3/4" Regular 14/S SR-HEF $ ft. 4-1/2 1/2" Regular 18/W SR-HEF $ ft. 10-1/2 3/4" Regular 6/S SR-HEF $ ft. 4-1/2 1/2" Regular 24/W SR-HEF $ ft. 10-1/2 3/4" Regular 8/S SR-HEF $ ft. 8 1/4" Skip 4/S SR-HEF $ ft. 10-1/2 3/4" Regular 14/S SR-HEF $ ft. 8 1/4" Skip 6/S SR-HEF $ ft. 10-1/ Regular 6/S SR-HEF $ ft. 9 1/2" Regular 14/S SR-HEF $ ft. 10-1/ Regular 8/S SR-HEF $ ft. 5 1/2" Regular 6/S SR-HEF $ ft. 10-1/ Regular 10/S SR-HEF $ ft. 5 1/2" Regular 10/S SR-HEF $ ft. 10-1/ Regular 14/S SR-HEF $ ft. 5 1/2" Regular 14/W SR-HEF $ ft Regular 6/S SR-HEF $ ft. 5 1/2" Regular 18/W SR-HEF $ ft Regular 8/S SR-HEF $ ft. 6 1/2" Regular 10/S SR-HEF $ ft Regular 10/S SR-HEF $ ft. 6 1/2" Regular 18/W SR-HEF $ ft Regular 14/S SR-HEF $ ft. 6 5/ Regular 14/S SR-HEF $ ft. 5 3/4" Regular 10/S SR-HEF $ ft. 9 1/2" Skip 4/S SR-HEF $ ft. 5 3/4" Regular 14/S SR-HEF $ ft. 9 1/2" Regular 6/S SR-HEF $ ft Regular 10/S SR-HEF $ ft. 9 1/2" Regular 10/S SR-HEF $ ft. 6 3/4" Regular 6/S SR-HEF $ ft. 9 1/2" Regular 14/W SR-HEF $ ft. 6 3/4" Regular 8/S SR-HEF $ ft. 9 1/2" Regular 18/W SR-HEF $ ft. 6 3/4" Regular 10/S SR-HEF $ ft. 9 5/ Regular 10/S SR-HEF $ ft. 6 3/4" Regular 14/S SR-HEF $ ft. 9 5/ Regular 14/S SR-HEF $ ft Regular 6/S SR-HEF $ ft. 9 3/4" Regular 6/S SR-HEF $ ft Regular 8/S SR-HEF $ ft. 9 3/4" Regular 10/S SR-HEF $ ft Regular 10/S SR-HEF $ ft. 9 3/4" Regular 14/S SR-HEF $ ft Regular 14/S SR-HEF $ ft. 9-1/2 1/4" Skip 4/S SR-HEF $ ft. 1/2" Regular 14/S SR-HEF $ ft. 9-1/2 1/4" Skip 6/S SR-HEF $ ft Regular 6/S SR-HEF $ ft. 9-1/2 3/ Skip 4/S SR-HEF $ ft Regular 10/S SR-HEF $ ft. 9-1/2 3/ Regular 6/S SR-HEF $ ft. 1 3/4" Regular 10/S SR-HEF $ ft. 9-1/2 3/ Regular 10/S SR-HEF $ ft. 6 1/4" Regular 14/S SR-HEF $ ft. 9-1/2 3/ Regular 14/S SR-HEF $ ft. 6 3/ Skip 4/S SR-HEF $ ft. 9-1/2 1/2" Skip 4/S SR-HEF $ ft. 6 3/ Regular 6/S SR-HEF $ ft. 9-1/2 1/2" Regular 6/S SR-HEF $ ft. 6 3/ Regular 14/S SR-HEF $ ft. 9-1/2 1/2" Regular 10/S SR-HEF $ ft. 6 1/2" Hook 4/H SR-HEF $ ft. 9-1/2 1/2" Regular 14/S SR-HEF $ ft. 6 1/2" Skip 4/S SR-HEF $ ft. 9-1/2 1/2" Regular 18/W SR-HEF $ ft. 6 1/2" Regular 6/S SR-HEF $ ft. 9-1/2 1/2" Regular 24/W SR-HEF $ ft. 6 1/2" Regular 10/S SR-HEF $ ft. 1/2" Regular 10/S SR-HEF $ ft. 6 1/2" Regular 14/W SR-HEF $ ft. 1/2" Regular 14/S SR-HEF $ ft. 6 1/2" Regular 18/W SR-HEF $ ft. 2 3/4" Regular 10/S SR-HEF $ ft. 6 3/4" Regular 10/S SR-HEF $ ft. 2-1/2 5/ Regular 10/S SR-HEF $ ft Regular 6/S SR-HEF $ ft. 2-1/2 5/ Regular 14/S SR-HEF $ ft Regular 8/S SR-HEF $ ft. 10 3/4" Regular 10/S SR-HEF $ ft Regular 10/S SR-HEF $ ft. 10 3/4" Regular 14/S SR-HEF $ ft Regular 14/S SR-HEF $ ft. 11 3/4" Regular 10/S SR-HEF $ ft. 10 1/2" Regular 10/S SR-HEF $ ft. 11 3/4" Regular 14/S SR-HEF $ ft Regular 8/S SR-HEF $ ft. 3/4" Regular 8/S SR-HEF $ ft Regular 10/S SR-HEF $ ft. 3/4" Regular 10/S SR-HEF $ ft Regular 14/S SR-HEF $ ft. 3/4" Regular 14/S SR-HEF $ ft Regular 10/S SR-HEF $ ft. 6 1/2" Regular 14/S SR-HEF $ ft. 6 1/2" Regular 10/S SR-HEF $ ft. 6 3/4" Regular 10/S SR-HEF $ ft. 6 3/4" Regular 6/S SR-HEF $ ft. 6 3/4" Regular 14/S SR-HEF $ ft. 6 3/4" Regular 10/S SR-HEF $ ft. 7-1/2 3/4" Regular 10/S SR-HEF $ ft. 8 3/4" Regular 6/S SR-HEF $ ft. 7-1/2 3/4" Regular 14/S SR-HEF $ ft. 8 3/4" Regular 8/S SR-HEF $28.67 Additional Lengths & Coil Stock Also Available! 14ft. 8 3/4" Regular 10/S SR-HEF $28.67 C

161 ANDSAW LADES/HOLE SAWS Intenss PRO (formerly Gladiator ) Triple Tempered M-42 Cobalt HSS WELDED-TO-LENGTH ANDSAW LADES Ideal for intensive production cutting operations across a wide range of metals Positive rake angle for optimum cutting efficiency in high-production cutting operations Triple tempered M-42 cobalt high speed steel teeth Production cutting of steels up to HRc 45, tool and stainless steels, nickel based and nonferrous alloys Easy penetration, excellent chip clearance and reduced noise levels High quality surface finish and faster and straighter cuts Length Width TPI 7ft. 9 3/ /P SR-GLAD $ ft. 9 3/ /P SR-GLAD $ ft. 9 3/ /P SR-GLAD $ ft. 10 3/ /P SR-GLAD $ ft /P SR-GLAD $ ft. 3/ /P SR-GLAD $ ft. 3/ /P SR-GLAD $ ft. 3/ /P SR-GLAD $ ft. 10-1/2 3/ /P SR-GLAD $ ft. 10-1/2 3/ /P SR-GLAD $ ft. 10-1/ /P SR-GLAD $ ft. 10-1/ /P SR-GLAD $ ft. 10-1/ /P SR-GLAD $ ft. 10-1/ /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft. 6 3/ /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $75.24 FASTCUT VARIALE PITCH HOLE SAWS All Purpose Saws With i-metal HSS Teeth Exceptionally strong and shatter resistant, Fastcut Variable Pitch Holesaws cut a wide variety of materials, including wood, metal and steel. They are suitable for hand held drills or in fixed applications, such as a stationary press. Ideal for light to medium production on carbon and alloy steels, stainless steels Cutting depth of 1-5/8 Variable pitch teeth (4-6 tooth) Carbide tipped hole saws also available HOLE SAW ARORS arbor is furnished with a high speed steel pilot drill. A set screw in the body allow for easy replacement of the pilot drill. Length Width Thickness Thickness Master Catalog 429 TPI 12ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft / /P SR-GLAD $ ft / /P SR-GLAD $ ft / /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft /P SR-GLAD $ ft / /P SR-GLAD $ ft / /P SR-GLAD $ ft / /P SR-GLAD $ ft / /8/P SR-GLAD $ Additional Lengths & Coil Stock Also Available! Please Call For More Information! Hole Saw meter Hole Saw meter 9/16 STR $ /2 STR $ /8 STR $ /8 STR $ /4 STR $ /4 STR $ /16 STR $ /8 STR $ /8 STR $ STR $ STR $ /8 STR $ /16 STR $ /4 STR $ /8 STR $ /2 STR $ /16 STR $ /4 STR $ /4 STR $ STR $ /8 STR $ /8 STR $ /2 STR $ /4 STR $ /8 STR $ /8 STR $ /8 STR $ /2 STR $ STR $ /4 STR $ /8 STR $ STR $ /4 STR $ /2 STR $ /8 STR $ STR $65.92 Saw. Thread 9/16" - 1-3/16 1/2" /4-8-9/32 5/8"-18 Chuck Size 3/8 11/32" Hex STR $9.40 1/4 1/4" Round STR $6.56 3/8 11/32" Hex STR $ /2 7/16" Round STR $14.24 C CARIDE INSERTS DEURRING

162 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD ANDSAW LADES/HOLE SAW KITS ROADAND i-metal High Speed Steel WELDED-TO-LENGTH ANDSAW LADES Ideal for production to general purpose cutting operations across a wide range of metals. M42 high speed edge improves wear resistance Oversized blade width increases beam strength Ideal for carbon, chrome, tool, die and stainless steels, nickel base steel, pipe and tube and mixed metal applications roadand delivers faster cutting rates, better cut finishes and longer blade life compared to other blades Designed for steel service centers, medium and large manufacturers, fabricators, maintenance shops, job shops and tool & die shops Length Width TPI lade Length Master Catalog Width Thickness Thickness TPI 7ft. 9 3/ /S SI $ ft /S SI $ ft /S SI $ ft /S SI $ ft. 5 3/ /S SI $ ft /S SI $ ft. 5 3/ /S SI $ ft /S SI $ ft. 10-1/2 3/ /S SI $ ft /S SI $ ft. 10-1/ /S SI $ ft / /S SI $ ft. 10-1/ /S SI $ ft / /S SI $ ft. 3/ /S SI $ ft / /S SI $ ft. 3/ /S SI $ ft /S SI $ ft /S SI $ ft /S SI $ ft /S SI $ ft /S SI $ ft /S SI $ ft / /S SI $ ft. 5 3/ /S SI $ ft / /S SI $ ft /S SI $ ft. 8 3/ /S SI $ ft. 6 3/ /S SI $ ft. 8 3/ /S SI $ ft. 6 3/ /S SI $ ft. 1-1/ /S SI $ ft /S SI $ ft. 1-1/ /S SI $ ft /S SI $ ft. 1-1/ /S SI $ ft / /S SI $ ft /S SI $ ft / /S SI $ ft / /S SI $ ft /S SI $ ft / /S SI $ ft /S SI $ ft / /S SI $ ft /S SI $ ft / /S SI $ ft. 1-1/ /S SI $ ft / /S SI $ ft. 1-1/ /S SI $ ft / /S SI $ ft. 1-1/ /S SI $ ft /S SI $67.43 Additional Lengths And Coil Stock 12ft /S SI $67.43 Also Available! Please Call For More Information! 12ft /S SI $ ft / /S SI $78.77 ANNULAR CUTTERS High Speed Steel-3/4 3/4 shank For general purpose hole making Easily makes large diameter holes without creating excessive chips Crafted of high speed steel, heat treated and tempered for maximum strength and rigidity Hardened and ground ALSO AVAILALE! Magnetic Drill Presses Please Call For More Information! WELDED TO LENGTH! NEW ITEM! lade 1" Depth of Cut 2" Depth of Cut 1" Depth of Cut 2" Depth of Cut Size Size 7/16 A $16.89 A $ /4 A $41.54 A $ /2 A $18.39 A $ /16 A $43.75 A $ /16 A $20.06 A $ /8 A $44.92 A $ /8 A $21.84 A $ /16 A $47.32 A $ /16 A $22.86 A $ /2 A $48.60 A $ /4 A $24.58 A $ /16 A $51.22 A $ /16 A $26.03 A $ /8 A $58.57 A $ /8 A $26.76 A $ /16 A $61.41 A $ /16 A $29.31 A $ /4 A $73.53 A $ A $30.14 A $ /16 A $74.98 A $ /16 A $35.60 A $ /8 A $77.97 A $ /8 A $37.61 A $ /16 A $79.54 A $ /16 A $38.63 A $ A $87.04 A $ C

163 DECIMAL EQUIVALENT/DRILL TAP CHARTS CONVERSION CHART Drill Size Decimal Equivalent Drill Size mm Dec. Equiv. Drill Size mm Dec. Equiv. Drill Size mm J / K / / / L M / / / / / N / / / / O / P / / / Q / R / / / S / / T / / / U / / / V / / W / / / / X / Y / A / / / Z / / / / C / D / / / / / / E / F / G / / / / / H / / I / / / TAP DRILL CHART Tap Size Drill Size Probable% of Thread Tap Size Drill Size Probable% of Thread Dec. Equiv. Tap Size Drill Size Drill Size Master Catalog 431 mm Probable% of Thread / M10x mm M24x3 53/ M1.6x mm M4x mm /16-14 U / / / / M2x.4 1/ M12x / / Dec. Equiv. Tap Size Drill Size mm Drill Size Dec. Equiv. Probable% of Thread / / /8-7 63/ / / / / M5x.8 4.2mm M14x2 15/ M30x /64 75 M2.5x mm / / / / / / / / / M6x / / / / / /8 37/ / / / M16x2 35/ M36x4 1-1/4 82 M3x /16-18 F / / / / /16-24 I / / / / M mm M20x2.5 11/ M3.5x /8-16 5/ /8-9 49/ /8-24 Q / / CARIDE INSERTS DEURRING

164 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD DRILL SETS-JOER, STU, SILVER & DEMING JOER DRILL SETS 13 Piece Set-1/16-1/4" x 64ths Master Catalog Material Drill Point Finish rand HSS 118 lack Oxide Precision Twist Drill PTD $21.15 M42 Cobalt 135 ronze Oxide Precision Twist Drill PTD $ Piece Set-1/16-1/2 x 32nds Material Drill Point Finish rand HSS 118 lack Oxide Precision Twist Drill PTD $55.63 HSS 118 right Morse MCT $60.68 HSS 118 TiN Coated TMX TMX $58.20 HSS Heavy Duty 135 TiN Coated TMX TMX $58.20 M42 Cobalt 135 ronze Oxide Precision Twist Drill PTD $96.01 Cobalt 135 right TMX TMX $ Piece Sets-1/16-3/8 x 64ths Material Drill Point Finish rand HSS 118 lack Oxide Precision Twist Drill PTD $51.43 M42 Cobalt 135 ronze Oxide Precision Twist Drill PTD $ Piece Sets-1/16-1/2 x 64ths Material Drill Point Finish rand HSS 118 right Precision Twist Drill PTD $ HSS 118 lack Oxide Precision Twist Drill PTD $ HSS 118 lack Oxide TMX TMX $82.45 HSS 118 right ISQ () A $99.50 HSS 118 TiN Coated TMX TMX $95.06 HSS 118 right Morse MCT $ HSS Heavy Duty 135 TiN Coated TMX TMX $95.06 M42 Cobalt 135 ronze Oxide Precision Twist Drill PTD $ Cobalt 135 right TMX TMX $ A-Z Letter Sizes-26 Piece Set Material Drill Point Finish rand HSS 118 right Morse MCT $ HSS 118 right Precision Twist Drill PTD $ HSS 118 TiN Coated TMX TMX $81.00 M42 Cobalt 135 ronze Oxide Precision Twist Drill PTD $ Cobalt 135 right TMX TMX $ #1-60 Piece Wire Sizes-60 Piece Set Material Drill Point Finish rand HSS 118 right Precision Twist Drill PTD $81.60 HSS 118 right Morse MCT $87.92 HSS 118 TiN Coated TMX TMX $55.29 M42 Cobalt 135 ronze Oxide Precision Twist Drill PTD $ Cobalt 135 right TMX TMX $85.36 Combo Sets-115 Pieces 1/16-1/2" x 64ths, A-Z, #1-60 Material Drill Point Finish rand HSS 118 TiN Coated ISQ (Import) A $99.50 HSS 118 lack Oxide TMX TMX $ HSS 118 right Morse MCT $ Metric Sets-y.5mm Increments Material Drill Point Finish rand HSS 118 lack Oxide TMX-19 Pc 1mm - 10mm TMX $38.80 Cobalt 135 right TMX-19 Pc 1mm - 10mm TMX $60.14 SCREW MACHINE SETS 1/16-1/2 X 64THS 29 Piece Set Material Drill Point Finish rand HSS 135 right Precision Twist Drill PTD $ M42 Cobalt 135 ronze Oxide Precision Twist Drill PTD $ SILVER & DEMING SETS 1/2 meter -6, 3 Flute Length Description Material rand 5 Pc Set: 1, 1-1/8,1-1/4, 1-3/8 & 1-1/2 8 Pc Set: 9/16,5/8, 11/16,3/4,13/16, 7/8,15/16,1 13 Pc Set: 17/32,9/16,19/32,5/8,21/32, 11/16,23/32,3/4,13/16,7/8,15/16,1 HSS TMX TMX $ Cobalt TMX TMX $ HSS TMX TMX $ HSS PTD PTD $ Cobalt TMX TMX $ Cobalt PTD PTD $ HSS TMX TMX $ Cobalt TMX TMX $417.69

165 JOER LENGTH DRILLS-HSS/COALT JOER LENGTH DRILLS General Purpose 118 Point On HSS & TiN Coated 135 Self-Centering Split Point On Cobalt HSS TMX Drills Sold In Package Quantities Fractional Sizes. Dec Equiv Tin Coated HSS 118 Point right Finish 118 Point lack Oxide 118 Point Cobalt HSS 135 Split Point TMX Features: 118 Point HSS TiN Coated Sold In Package Quantities- 1/64 to 17/64: 10 per pack 9/32 to 1/2: 5 per pack Over 1/2 : 1 per pack Wire Gage: 10 per pack Letter- A to I: 10 per pack J to Z: 5 per pack 1/ /4 TMX-1/64-JHTN $0.77 PTD-1/64-JHRN $1.94 PTD-1/64-JHN $1.94 PTD-1/64-JCGS $3.04 1/ /8 TMX-1/32-JHTN $0.65 PTD-1/32-JHRN $1.17 PTD-1/32-JHN $1.17 PTD-1/32-JCGS $2.49 3/ /4 TMX-3/64-JHTN $0.65 PTD-3/64-JHRN $1.17 PTD-3/64-JHN $1.17 PTD-3/64-JCGS $1.79 1/ /8 TMX-1/16-JHTN $0.65 PTD-1/16-JHRN $1.08 PTD-1/16-JHN $1.08 PTD-1/16-JCGS $1.63 5/ TMX-5/64-JHTN $0.65 PTD-5/64-JHRN $1.09 PTD-5/64-JHN $1.09 PTD-5/64-JCGS $1.63 3/ /4 TMX-3/32-JHTN $0.65 PTD-3/32-JHRN $1.09 PTD-3/32-JHN $1.09 PTD-3/32-JCGS $1.63 7/ /8 TMX-7/64-JHTN $0.65 PTD-7/64-JHRN $1.15 PTD-7/64-JHN $1.15 PTD-7/64-JCGS $1.72 1/ /4 TMX-1/8-JHTN $0.65 PTD-1/8-JHRN $1.12 PTD-1/8-JHN $1.12 PTD-1/8-JCGS $2.08 9/ /8 TMX-9/64-JHTN $0.83 PTD-9/64-JHRN $1.24 PTD-9/64-JHN $1.24 PTD-9/64-JCGS $2.11 5/ /8 TMX-5/32-JHTN $0.83 PTD-5/32-JHRN $1.26 PTD-5/32-JHN $1.26 PTD-5/32-JCGS $ / /4 TMX-11/64-JHTN $0.97 PTD-11/64-JHRN $1.37 PTD-11/64-JHN $1.38 PTD-11/64-JCGS $2.49 3/ /2 TMX-3/16-JHTN $1.11 PTD-3/16-JHRN $1.53 PTD-3/16-JHN $1.53 PTD-3/16-JCGS $ / /8 TMX-13/64-JHTN $1.16 PTD-13/64-JHRN $1.69 PTD-13/64-JHN $1.69 PTD-13/64-JCGS $3.34 7/ /4 TMX-7/32-JHTN $1.39 PTD-7/32-JHRN $1.87 PTD-7/32-JHN $1.87 PTD-7/32-JCGS $ / /8 TMX-15/64-JHTN $1.51 PTD-15/64-JHRN $2.03 PTD-15/64-JHN $2.03 PTD-15/64-JCGS $3.89 1/ TMX-1/4-JHTN $1.70 PTD-1/4-JHRN $2.13 PTD-1/4-JHN $2.13 PTD-1/4-JCGS $ / /8 TMX-17/64-JHTN $1.98 PTD-17/64-JHRN $2.58 PTD-17/64-JHN $2.60 PTD-17/64-JCGS $4.70 9/ /4 TMX-9/32-JHTN $2.34 PTD-9/32-JHRN $2.66 PTD-9/32-JHN $2.66 PTD-9/32-JCGS $ / /8 TMX-19/64-JHTN $2.45 PTD-19/64-JHRN $3.10 PTD-19/64-JHN $3.10 PTD-19/64-JCGS $6.03 5/ /2 TMX-5/16-JHTN $2.86 PTD-5/16-JHRN $3.42 PTD-5/16-JHN $3.42 PTD-5/16-JCGS $ / /8 TMX-21/64-JHTN $2.86 PTD-21/64-JHRN $3.81 PTD-21/64-JHN $3.81 PTD-21/64-JCGS $ / /4 TMX-11/32-JHTN $3.12 PTD-11/32-JHRN $4.22 PTD-11/32-JHN $4.23 PTD-11/32-JCGS $ / /8 TMX-23/64-JHTN $3.66 PTD-23/64-JHRN $4.77 PTD-23/64-JHN $4.75 PTD-23/64-JCGS $8.98 3/ TMX-3/8-JHTN $4.13 PTD-3/8-JHRN $4.86 PTD-3/8-JHN $4.86 PTD-3/8-JCGS $ / /8 TMX-25/64-JHTN $4.60 PTD-25/64-JHRN $5.58 PTD-25/64-JHN $5.58 PTD-25/64-JCGS $ / /4 TMX-13/32-JHTN $4.96 PTD-13/32-JHRN $5.69 PTD-13/32-JHN $5.72 PTD-13/32-JCGS $ / /8 TMX-27/64-JHTN $5.66 PTD-27/64-JHRN $6.35 PTD-27/64-JHN $6.39 PTD-27/64-JCGS $ / /2 TMX-7/16-JHTN $5.66 PTD-7/16-JHRN $6.62 PTD-7/16-JHN $6.62 PTD-7/16-JCGS $ / /8 TMX-29/64-JHTN $6.37 PTD-29/64-JHRN $7.43 PTD-29/64-JHN $7.40 PTD-29/64-JCGS $ / /4 TMX-15/32-JHTN $6.84 PTD-15/32-JHRN $7.85 PTD-15/32-JHN $7.83 PTD-15/32-JCGS $ / /8 TMX-31/64-JHTN $7.08 PTD-31/64-JHRN $8.28 PTD-31/64-JHN $8.24 PTD-31/64-JCGS $ / TMX-1/2-JHTN $8.02 PTD-1/2-JHRN $8.21 PTD-1/2-JHN $8.26 PTD-1/2-JCGS $ / /8 TMX-33/64-JHTN $8.02 PTD-33/64-JHRN $14.96 PTD-33/64-JHN $14.96 PTD-33/64-JCGS $ / /8 TMX-17/32-JHTN $10.62 PTD-17/32-JHRN $15.41 PTD-17/32-JHN $15.41 PTD-17/32-JCGS $ / /8 TMX-35/64-JHTN $10.62 PTD-35/64-JHRN $16.99 PTD-35/64-JHN $16.99 PTD-35/64-JCGS $ / /8 TMX-9/16-JHTN $11.80 PTD-9/16-JHRN $17.46 PTD-9/16-JHN $17.46 PTD-9/16-JCGS $ / /8 TMX-37/64-JHTN $14.75 PTD-37/64-JHRN $17.84 PTD-37/64-JHN $18.32 PTD-37/64-JCGS $ / /8 TMX-19/32-JHTN $14.75 PTD-19/32-JHRN $18.32 PTD-19/32-JHN $18.32 PTD-19/32-JCGS $ / /8 TMX-39/64-JHTN $14.75 PTD-39/64-JHRN $19.62 PTD-39/64-JHN $19.62 PTD-39/64-JCGS $ / /8 TMX-5/8-JHTN $15.93 PTD-5/8-JHRN $19.26 PTD-5/8-JHN $19.26 PTD-5/8-JCGS $ / /8 TMX-41/64-JHTN $17.23 PTD-41/64-JHRN - PTD-41/64-JHN $21.69 PTD-41/64-JCGS $ / /8 TMX-21/32-JHTN $17.23 PTD-21/32-JHRN $22.77 PTD-21/32-JHN $22.77 PTD-21/32-JCGS $ / /8 TMX-43/64-JHTN $18.88 PTD-43/64-JHRN $24.57 PTD-43/64-JHN $24.57 PTD-43/64-JCGS $ / /8 TMX-11/16-JHTN $18.88 PTD-11/16-JHRN $24.57 PTD-11/16-JHN $24.57 PTD-11/16-JCGS $45.90 DRILL INDEXES Holds and organizes your jobber length fractional, letter and wire gauge drills Drill Type Description NEW ITEM! Master Catalog 433 Cap. Letter A to Z drill index 26 HU $12.60 Jobber 1/16" to 1/2" x 32nds drill index 15 HU $11.03 Jobber 1/16" to 1/2" x 64ths drill index 29 HU $11.03 Wire Gage #1 to 60 wire gage drill index 60 HU $10.80 Wire Gage #1 to 80 wire gage 80 HU $32.40 Combo 29 Frac., 26 Letter & 60 wire Gage 115 HU $40.50 C CARIDE INSERTS DEURRING

166 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD JOER LENGTH DRILLS-HSS/COALT JOER LENGTH DRILLS General Purpose 118 Point On HSS & TiN Coated 135 Self-Centering Split Point On Cobalt HSS TMX Drills Sold In Package Quantities. Wire Sizes Dec Equiv right Finish 118 Point lack Oxide 118 Point Master Catalog Cobalt HSS 135 Split Point TMX Features: 118 Point HSS TiN Coated Sold In Package Quantities- Wire Gage: 10 per pack Tin Coated HSS 118 Point /8 PTD-1-JHRN $2.27 PTD-1-JHN $2.26 PTD-1-JCGS $4.46 TMX-1-JHTN $ /8 PTD-2-JHRN $2.29 PTD-2-JHN $2.28 PTD-2-JCGS $4.45 TMX-2-JHTN $ /4 PTD-3-JHRN $2.06 PTD-3-JHN $2.05 PTD-3-JCGS $4.16 TMX-3-JHTN $ /4 PTD-4-JHRN $2.08 PTD-4-JHN $2.07 PTD-4-JCGS $4.18 TMX-4-JHTN $ /4 PTD-5-JHRN $2.08 PTD-5-JHN $2.07 PTD-5-JCGS $4.18 TMX-5-JHTN $ /4 PTD-6-JHRN $2.08 PTD-6-JHN $2.07 PTD-6-JCGS $4.18 TMX-6-JHTN $ /8 PTD-7-JHRN $1.80 PTD-7-JHN $1.79 PTD-7-JCGS $3.24 TMX-7-JHTN $ /8 PTD-8-JHRN $1.85 PTD-8-JHN $1.84 PTD-8-JCGS $3.24 TMX-8-JHTN $ /8 PTD-9-JHRN $1.84 PTD-9-JHN $1.84 PTD-9-JCGS $3.24 TMX-9-JHTN $ /8 PTD-10-JHRN $1.81 PTD-10-JHN $1.81 PTD-10-JCGS $3.24 TMX-10-JHTN $ /2 PTD-11-JHRN $1.68 PTD-11-JHN $1.68 PTD-11-JCGS $3.24 TMX-11-JHTN $ /2 PTD-12-JHRN $1.71 PTD-12-JHN $1.70 PTD-12-JCGS $3.24 TMX-12-JHTN $ /2 PTD-13-JHRN $1.67 PTD-13-JHN $1.66 PTD-13-JCGS $3.11 TMX-13-JHTN $ /8 PTD-14-JHRN $1.67 PTD-14-JHN $1.67 PTD-14-JCGS $3.12 TMX-14-JHTN $ /8 PTD-15-JHRN $1.67 PTD-15-JHN $1.67 PTD-15-JCGS $3.12 TMX-15-JHTN $ /8 PTD-16-JHRN $1.67 PTD-16-JHN $1.66 PTD-16-JCGS $2.90 TMX-16-JHTN $ /8 PTD-17-JHRN $1.67 PTD-17-JHN $1.66 PTD-17-JCGS $2.85 TMX-17-JHTN $ /4 PTD-18-JHRN $1.39 PTD-18-JHN $1.38 PTD-18-JCGS $2.60 TMX-18-JHTN $ /4 PTD-19-JHRN $1.37 PTD-19-JHN $1.37 PTD-19-JCGS $2.52 TMX-19-JHTN $ /4 PTD-20-JHRN $1.36 PTD-20-JHN $1.37 PTD-20-JCGS $2.52 TMX-20-JHTN $ /4 PTD-21-JHRN $1.26 PTD-21-JHN $1.26 PTD-21-JCGS $2.50 TMX-21-JHTN $ /8 PTD-22-JHRN $1.28 PTD-22-JHN $1.27 PTD-22-JCGS $2.52 TMX-22-JHTN $ /8 PTD-23-JHRN $1.28 PTD-23-JHN $1.28 PTD-23-JCGS $2.52 TMX-23-JHTN $ /8 PTD-24-JHRN $1.28 PTD-24-JHN $1.27 PTD-24-JCGS $2.50 TMX-24-JHTN $ PTD-25-JHRN $1.21 PTD-25-JHN $1.21 PTD-25-JCGS $2.28 TMX-25-JHTN $ PTD-26-JHRN $1.22 PTD-26-JHN $1.21 PTD-26-JCGS $2.27 TMX-26-JHTN $ PTD-27-JHRN $1.21 PTD-27-JHN $1.21 PTD-27-JCGS $2.26 TMX-27-JHTN $ /8 PTD-28-JHRN $1.13 PTD-28-JHN $1.13 PTD-28-JCGS $2.12 TMX-28-JHTN $ /8 PTD-29-JHRN $1.10 PTD-29-JHN $1.10 PTD-29-JCGS $2.06 TMX-29-JHTN $ /4 PTD-30-JHRN $1.10 PTD-30-JHN $1.10 PTD-30-JCGS $1.92 TMX-30-JHTN $ /4 PTD-31-JHRN $1.09 PTD-31-JHN $1.09 PTD-31-JCGS $1.90 TMX-31-JHTN $ /4 PTD-32-JHRN $1.10 PTD-32-JHN $1.09 PTD-32-JCGS $1.87 TMX-32-JHTN $ /8 PTD-33-JHRN $1.10 PTD-33-JHN $1.09 PTD-33-JCGS $1.79 TMX-33-JHTN $ /8 PTD-34-JHRN $1.10 PTD-34-JHN $1.09 PTD-34-JCGS $1.80 TMX-34-JHTN $ /8 PTD-35-JHRN $1.10 PTD-35-JHN $1.09 PTD-35-JCGS $1.79 TMX-35-JHTN $ /2 PTD-36-JHRN $1.08 PTD-36-JHN $1.08 PTD-36-JCGS $1.77 TMX-36-JHTN $ /2 PTD-37-JHRN $1.10 PTD-37-JHN $1.09 PTD-37-JCGS $1.77 TMX-37-JHTN $ /2 PTD-38-JHRN $1.10 PTD-38-JHN $1.09 PTD-38-JCGS $1.66 TMX-38-JHTN $ /8 PTD-39-JHRN $1.10 PTD-39-JHN $1.09 PTD-39-JCGS $1.66 TMX-39-JHTN $ /8 PTD-40-JHRN $1.08 PTD-40-JHN $1.08 PTD-40-JCGS $1.66 TMX-40-JHTN $ /8 PTD-41-JHRN $1.10 PTD-41-JHN $1.09 PTD-41-JCGS $1.63 TMX-41-JHTN $ /4 PTD-42-JHRN $1.10 PTD-42-JHN $1.09 PTD-42-JCGS $1.61 TMX-42-JHTN $ /4 PTD-43-JHRN $1.08 PTD-43-JHN $1.09 PTD-43-JCGS $1.61 TMX-43-JHTN $ /8 PTD-44-JHRN $1.08 PTD-44-JHN $1.09 PTD-44-JCGS $1.61 TMX-44-JHTN $ /8 PTD-45-JHRN $1.10 PTD-45-JHN $1.09 PTD-45-JCGS $1.61 TMX-45-JHTN $ /8 PTD-46-JHRN $1.10 PTD-46-JHN $1.09 PTD-46-JCGS $1.61 TMX-46-JHTN $ PTD-47-JHRN $1.10 PTD-47-JHN $1.09 PTD-47-JCGS $1.61 TMX-47-JHTN $ PTD-48-JHRN $1.10 PTD-48-JHN $1.10 PTD-48-JCGS $1.61 TMX-48-JHTN $ PTD-49-JHRN $1.10 PTD-49-JHN $1.10 PTD-49-JCGS $1.61 TMX-49-JHTN $ PTD-50-JHRN $1.09 PTD-50-JHN $1.09 PTD-50-JCGS $1.61 TMX-50-JHTN $ PTD-51-JHRN $1.10 PTD-51-JHN $1.09 PTD-51-JCGS $1.61 TMX-51-JHTN $ /8 PTD-52-JHRN $1.09 PTD-52-JHN $1.09 PTD-52-JCGS $1.61 TMX-52-JHTN $ /8 PTD-53-JHRN $1.09 PTD-53-JHN $1.16 PTD-53-JCGS $1.80 TMX-53-JHTN $ /8 PTD-54-JHRN $1.09 PTD-54-JHN $1.16 PTD-54-JCGS $1.80 TMX-54-JHTN $ /8 PTD-55-JHRN $1.09 PTD-55-JHN $1.16 PTD-55-JCGS $1.80 TMX-55-JHTN $ /4 PTD-56-JHRN $1.10 PTD-56-JHN $1.16 PTD-56-JCGS $2.04 TMX-56-JHTN $ /4 PTD-57-JHRN $1.09 PTD-57-JHN $1.16 PTD-57-JCGS $2.04 TMX-57-JHTN $ /8 PTD-58-JHRN $1.13 PTD-58-JHN $1.16 PTD-58-JCGS $2.05 TMX-58-JHTN $ /8 PTD-59-JHRN $1.13 PTD-59-JHN $1.17 PTD-59-JCGS $2.04 TMX-59-JHTN $ /8 PTD-60-JHRN $1.13 PTD-60-JHN $1.16 PTD-60-JCGS $2.04 TMX-60-JHTN $0.65 NEW ITEM! C

167 JOER LENGTH DRILLS-HSS/COALT JOER LENGTH DRILLS General Purpose 118 Point On HSS & TiN Coated 135 Self-Centering Split Point On Cobalt HSS C TMX Features: 118 Point HSS TiN Coated Sold In Package Quantities- Letter- A to I: 10 per pack J to Z: 5 per pack. Letter Sizes Dec Equiv right Finish 118 Point lack Oxide 118 Point Cobalt HSS 135 Split Point Tin Coated HSS 118 Point A /8 PTD-A-JHRN $2.58 PTD-A-JHN $2.58 PTD-A-JCGS $4.50 TMX-A-JHTN $ PTD--JHRN $2.58 PTD--JHN $2.58 PTD--JCGS $5.22 TMX--JHTN $1.70 C PTD-C-JHRN $2.58 PTD-C-JHN $2.58 PTD-C-JCGS $5.22 TMX-C-JHTN $1.70 D PTD-D-JHRN $2.58 PTD-D-JHN $2.58 PTD-D-JCGS $5.85 TMX-D-JHTN $1.70 E PTD-E-JHRN $2.40 PTD-E-JHN $2.39 PTD-E-JCGS $4.57 TMX-E-JHTN $1.98 F /8 PTD-F-JHRN $2.75 PTD-F-JHN $2.75 PTD-F-JCGS $5.13 TMX-F-JHTN $1.98 G /8 PTD-G-JHRN $3.09 PTD-G-JHN $3.08 PTD-G-JCGS $5.22 TMX-G-JHTN $1.98 H /8 PTD-H-JHRN $3.09 PTD-H-JHN $3.09 PTD-H-JCGS $5.85 TMX-H-JHTN $2.34 I /8 PTD-I-JHRN $3.09 PTD-I-JHN $3.08 PTD-I-JCGS $5.49 TMX-I-JHTN $2.34 J /8 PTD-J-JHRN $3.31 PTD-J-JHN $3.31 PTD-J-JCGS $5.85 TMX-J-JHTN $2.34 K /4 PTD-K-JHRN $3.66 PTD-K-JHN $3.66 PTD-K-JCGS $5.85 TMX-K-JHTN $2.34 L /4 PTD-L-JHRN $3.66 PTD-L-JHN $3.66 PTD-L-JCGS $6.66 TMX-L-JHTN $2.45 M /8 PTD-M-JHRN $3.87 PTD-M-JHN $3.87 PTD-M-JCGS $7.04 TMX-M-JHTN $2.45 N /8 PTD-N-JHRN $3.87 PTD-N-JHN $3.87 PTD-N-JCGS $7.04 TMX-N-JHTN $2.86 O /2 PTD-O-JHRN $3.91 PTD-O-JHN $3.91 PTD-O-JCGS $7.79 TMX-O-JHTN $2.86 P /8 PTD-P-JHRN $4.42 PTD-P-JHN $4.42 PTD-P-JCGS $8.28 TMX-P-JHTN $2.86 Q /4 PTD-Q-JHRN $4.42 PTD-Q-JHN $4.40 PTD-Q-JCGS $8.60 TMX-Q-JHTN $3.12 R /4 PTD-R-JHRN $4.73 PTD-R-JHN $4.73 PTD-R-JCGS $8.60 TMX-R-JHTN $3.12 S /8 PTD-S-JHRN $5.00 PTD-S-JHN $5.00 PTD-S-JCGS $10.51 TMX-S-JHTN $3.66 T /8 PTD-T-JHRN $5.69 PTD-T-JHN $5.69 PTD-T-JCGS $10.51 TMX-T-JHTN $3.66 U PTD-U-JHRN $5.69 PTD-U-JHN $5.69 PTD-U-JCGS $10.51 TMX-U-JHTN $4.13 V PTD-V-JHRN $5.85 PTD-V-JHN $5.85 PTD-V-JCGS $11.59 TMX-V-JHTN $4.60 W /8 PTD-W-JHRN $6.05 PTD-W-JHN $6.05 PTD-W-JCGS $11.59 TMX-W-JHTN $4.60 X /8 PTD-X-JHRN $7.36 PTD-X-JHN $7.36 PTD-X-JCGS $11.59 TMX-X-JHTN $4.96 Y /4 PTD-Y-JHRN $8.24 PTD-Y-JHN $8.24 PTD-Y-JCGS $12.26 TMX-Y-JHTN $4.96 Z /4 PTD-Z-JHRN $8.75 PTD-Z-JHN $8.75 PTD-Z-JCGS $13.37 TMX-Z-JHTN $5.66 MASTER DRILL DISPENSERS Holds full packages (minimum of 12 pcs.) of jobber or screw machine length drills, fractional, letter and wire gauge sizes in one compete cabinet. Dimensions: 26 W x 12 D x 12 1/2 H Weight: 43 lbs. TMX Drills Sold In Package Quantities Description Master Drill Dispenser HU $ DIAMOND PLATE SPONGECOTE Anti-Fatigue Mats-No. 415 mond-plate SpongeCote is the most popular anti-fatigue mat in the industry because no other offers such a complete package of exceptional comfort, long life, and a high-tech, industrial image. Its exceptionally resilient Nitricell sponge base defines the mat by providing true comfort, enhancing productivity, and reviving morale, all while relieving fatigue throughout the day. lack/yellow Trim lack IT UDDY Clip-on cup drill index High impact, break resistant plastic Water resistant, great for outdoor jobsites Fast, 1/4 turn cover secures dome to top of it uddy Drills stay in it uddy if dropped and cover is on If your 1/2" drill bit is 6", order Jobber Length it uddy (HU-30550). Description For Jobbers-1/16 to 1/2 x 64ths HU $16.50 For Mechanics drills-1/16 to 1/2 x 64ths HU $16.50 For use in dry work areas Anti-fatigue Nitricell sponge base for unparalleled comfort Safety beveled edges Slip and wear resistant 3 Year Warranty NEW ITEM! EST SELLER! Ideal For Heavily Trafficked Areas! Size Thickness Color 2' x 3 9/16 lack WW K $47.27 lk/yellow WW Y $ ' x 5 9/16 lack WW K $ lk/yellow WW Y $ Master Catalog 435 CARIDE INSERTS DEURRING

168 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID CARIDE DRILLS-JOER LENGTH JOER LENGTH DRILLS SOLID CARIDE FEATURES: For use on non-ferrous alloys, cast iron, plastics, aluminum and highly abrasive materials Made from premium submicron carbide with 10% cobalt 20 helix, right hand spiral, right hand cut 118 drill point Made in Full Line Available! Please call for more information. DRILL DISPENSERS Holds full packages of each size drill (minimum 12 pcs.). One piece drawer slide for long useful life. Stackable for larger inventories. Dimensions: 14 5/8 W x 7 3/8 D x 7 3/4 H The Original For Drill sizes 1/16" to 1/2" x 64ths jobber drills #1 to #60 wire gage drills, jobbers length A to Z jobber length drills HU $82.39 HU $ HU $82.39 Size Dec. LOC Master Catalog Uncoated TiN Coated TiAlN Coated /16 3/4 JRUC-80-MO $12.86 JRTN-80-MO $14.40 JRTA-80-MO $ /16 3/4 JRUC-79-MO $12.86 JRTN-79-MO $14.40 JRTA-79-MO $ / /16 3/4 JRUC-1/64-MO $12.86 JRTN-1/64-MO $14.40 JRTA-1/64-MO $ /16 3/4 JRUC-78-MO $12.86 JRTN-78-MO $14.40 JRTA-78-MO $ /16 3/4 JRUC-77-MO $12.43 JRTN-77-MO $14.40 JRTA-77-MO $ /4 7/8 JRUC-76-MO $12.43 JRTN-76-MO $14.40 JRTA-76-MO $ /4 7/8 JRUC-75-MO $12.43 JRTN-75-MO $14.40 JRTA-75-MO $ /4 7/8 JRUC-74-MO $12.43 JRTN-74-MO $14.40 JRTA-74-MO $ /4 7/8 JRUC-73-MO $12.43 JRTN-73-MO $14.40 JRTA-73-MO $ /16 1 JRUC-72-MO $11.99 JRTN-72-MO $12.86 JRTA-72-MO $ /16 1 JRUC-71-MO $11.99 JRTN-71-MO $12.86 JRTA-71-MO $ /2 1-1/2 JRUC-70-MO $11.99 JRTN-70-MO $12.86 JRTA-70-MO $ /2 1-1/2 JRUC-69-MO $11.99 JRTN-69-MO $12.86 JRTA-69-MO $ /2 1-1/2 JRUC-68-MO $11.11 JRTN-68-MO $12.86 JRTA-68-MO $ / /2 1-1/2 JRUC-1/32-MO $7.89 JRTN-1/32-MO $12.86 JRTA-1/32-MO $ /2 1-1/2 JRUC-67-MO $11.11 JRTN-67-MO $12.86 JRTA-67-MO $ /2 1-1/2 JRUC-66-MO $11.11 JRTN-66-MO $12.86 JRTA-66-MO $ /8 1-1/2 JRUC-65-MO $9.36 JRTN-65-MO $12.86 JRTA-65-MO $ /8 1-1/2 JRUC-64-MO $9.36 JRTN-64-MO $12.86 JRTA-64-MO $ /8 1-1/2 JRUC-63-MO $9.36 JRTN-63-MO $12.86 JRTA-63-MO $ /8 8 JRUC-62-MO $9.36 JRTN-62-MO $12.86 JRTA-62-MO $ /8 1-1/2 JRUC-61-MO $9.36 JRTN-61-MO $12.86 JRTA-61-MO $ /4 1-1/2 JRUC-60-MO $9.36 JRTN-60-MO $12.86 JRTA-60-MO $ /4 1-1/2 JRUC-59-MO $9.36 JRTN-59-MO $11.11 JRTA-59-MO $ /4 1-1/2 JRUC-58-MO $9.36 JRTN-58-MO $11.11 JRTA-58-MO $ /4 1-1/2 JRUC-57-MO $9.36 JRTN-57-MO $11.11 JRTA-57-MO $ /4 1-1/2 JRUC-56-MO $7.09 JRTN-56-MO $8.84 JRTA-56-MO $9.71 3/ /4 1-1/2 JRUC-3/64-MO $6.69 JRTN-3/64-MO $8.84 JRTA-3/64-MO $ /4 1-1/2 JRUC-55-MO $7.09 JRTN-55-MO $8.84 JRTA-55-MO $ /4 1-1/2 JRUC-54-MO $7.09 JRTN-54-MO $8.84 JRTA-54-MO $ /4 1-1/2 JRUC-53-MO $7.49 JRTN-53-MO $8.84 JRTA-53-MO $9.71 1/ /4 1-1/2 JRUC-1/16-MO $5.95 JRTN-1/16-MO $8.84 JRTA-1/16-MO $ /4 1-1/2 JRUC-52-MO $7.09 JRTN-52-MO $8.84 JRTA-52-MO $ /4 1-1/2 JRUC-51-MO $7.09 JRTN-51-MO $8.84 JRTA-51-MO $ /8 1-3/4 JRUC-50-MO $7.39 JRTN-50-MO $9.14 JRTA-50-MO $ /8 1-3/4 JRUC-49-MO $7.39 JRTN-49-MO $9.14 JRTA-49-MO $ /8 1-3/4 JRUC-48-MO $7.39 JRTN-48-MO $9.14 JRTA-48-MO $ / /8 1-3/4 JRUC-5/64-MO $6.08 JRTN-5/64-MO $9.14 JRTA-5/64-MO $ /8 1-3/4 JRUC-47-MO $7.39 JRTN-47-MO $9.14 JRTA-47-MO $ /8 1-3/4 JRUC-46-MO $7.39 JRTN-46-MO $9.14 JRTA-46-MO $ /8 1-3/4 JRUC-45-MO $7.39 JRTN-45-MO $9.14 JRTA-45-MO $ JRUC-44-MO $6.88 JRTN-44-MO $8.63 JRTA-44-MO $ JRUC-43-MO $6.88 JRTN-43-MO $8.63 JRTA-43-MO $ JRUC-42-MO $6.88 JRTN-42-MO $8.63 JRTA-42-MO $9.51 3/ JRUC-3/32-MO $6.36 JRTN-3/32-MO $8.63 JRTA-3/32-MO $ JRUC-41-MO $6.88 JRTN-41-MO $8.63 JRTA-41-MO $ JRUC-40-MO $6.88 JRTN-40-MO $8.63 JRTA-40-MO $ /4 2-1/4 JRUC-39-MO $8.05 JRTN-39-MO $9.80 JRTA-39-MO $ /4 2-1/4 JRUC-38-MO $8.05 JRTN-38-MO $9.80 JRTA-38-MO $ /4 2-1/4 JRUC-37-MO $8.05 JRTN-37-MO $9.80 JRTA-37-MO $ /4 2-1/4 JRUC-36-MO $8.40 JRTN-36-MO $9.80 JRTA-36-MO $ / /4 2-1/4 JRUC-7/64-MO $6.65 JRTN-7/64-MO $9.80 JRTA-7/64-MO $ /4 2-1/4 JRUC-35-MO $8.05 JRTN-35-MO $9.80 JRTA-35-MO $ /4 2-1/4 JRUC-34-MO $8.40 JRTN-34-MO $10.15 JRTA-34-MO $ /4 2-1/4 JRUC-33-MO $8.40 JRTN-33-MO $10.15 JRTA-33-MO $ /4 2-1/4 JRUC-32-MO $8.40 JRTN-32-MO $10.15 JRTA-32-MO $ /4 2-1/4 JRUC-31-MO $8.05 JRTN-31-MO $9.80 JRTA-31-MO $ / /4 2-1/4 JRUC-1/8-MO $8.05 JRTN-1/8-MO $9.80 JRTA-1/8-MO $ /4 2-1/4 JRUC-30-MO $8.05 JRTN-30-MO $9.80 JRTA-30-MO $ /8 2-1/2 JRUC-29-MO $10.31 JRTN-29-MO $12.50 JRTA-29-MO $ /8 2-1/2 JRUC-28-MO $10.31 JRTN-28-MO $12.50 JRTA-28-MO $ / /8 2-1/2 JRUC-9/64-MO $10.31 JRTN-9/64-MO $12.50 JRTA-9/64-MO $ /8 2-1/2 JRUC-27-MO $10.31 JRTN-27-MO $12.50 JRTA-27-MO $ /8 2-1/2 JRUC-26-MO $10.31 JRTN-26-MO $12.50 JRTA-26-MO $ /8 2-1/2 JRUC-25-MO $10.31 JRTN-25-MO $12.50 JRTA-25-MO $ /8 2-1/2 JRUC-24-MO $10.31 JRTN-24-MO $12.50 JRTA-24-MO $ /8 2-1/2 JRUC-23-MO $10.31 JRTN-23-MO $12.50 JRTA-23-MO $ / /8 2-1/2 JRUC-5/32-MO $10.31 JRTN-5/32-MO $12.50 JRTA-5/32-MO $ /8 2-1/2 JRUC-22-MO $10.31 JRTN-22-MO $12.50 JRTA-22-MO $13.52 C

169 SOLID CARIDE DRILLS-JOER LENGTH JOER LENGTH DRILLS (continued) SOLID CARIDE FEATURES: For use on non-ferrous alloys, cast iron, plastics, aluminum and highly abrasive materials Made from premium submicron carbide with 10% cobalt 20 helix, right hand spiral, right hand cut 118 drill point Made in DRILL INDEXES Holds and organizes your letter size, jobber length fractional and wire gauge drills. For Drill Sizes A to Z drill index HU $ /16" to 1/2" x 64ths drill index #1 to 60 wire gage drill index Full Line Available! Please call for more information. HU $12.60 HU $10.80 Size Dec. LOC Uncoated TiN Coated TiAlN Coated /8 2-1/2 JRUC-21-MO $10.31 JRTN-21-MO $12.50 JRTA-21-MO $ /8 2-1/2 JRUC-20-MO $10.31 JRTN-20-MO $12.50 JRTA-20-MO $ /8 2-3/4 JRUC-19-MO $11.92 JRTN-19-MO $14.11 JRTA-19-MO $ /8 2-3/4 JRUC-18-MO $11.92 JRTN-18-MO $14.11 JRTA-18-MO $ / /8 2-3/4 JRUC-11/64-MO $11.92 JRTN-11/64-MO $14.11 JRTA-11/64-MO $ /8 2-3/4 JRUC-17-MO $11.92 JRTN-17-MO $14.11 JRTA-17-MO $ /8 2-3/4 JRUC-16-MO $12.27 JRTN-16-MO $14.46 JRTA-16-MO $ /8 2-3/4 JRUC-15-MO $12.27 JRTN-15-MO $14.46 JRTA-15-MO $ /8 2-3/4 JRUC-14-MO $12.27 JRTN-14-MO $14.46 JRTA-14-MO $ /8 2-3/4 JRUC-13-MO $12.27 JRTN-13-MO $14.46 JRTA-13-MO $ / /8 2-3/4 JRUC-3/16-MO $12.27 JRTN-3/16-MO $14.46 JRTA-3/16-MO $ /8 2-3/4 JRUC-12-MO $12.27 JRTN-12-MO $14.46 JRTA-12-MO $ /8 2-3/4 JRUC-11-MO $12.27 JRTN-11-MO $15.19 JRTA-11-MO $ /8 2-3/4 JRUC-10-MO $12.27 JRTN-10-MO $15.19 JRTA-10-MO $ /4 3 JRUC-9-MO $14.03 JRTN-9-MO $16.95 JRTA-9-MO $ /4 3 JRUC-8-MO $14.03 JRTN-8-MO $16.95 JRTA-8-MO $ /4 3 JRUC-7-MO $14.03 JRTN-7-MO $16.95 JRTA-7-MO $ / /4 3 JRUC-13/64-MO $14.73 JRTN-13/64-MO $17.65 JRTA-13/64-MO $ /4 3 JRUC-6-MO $14.73 JRTN-6-MO $17.65 JRTA-6-MO $ /4 3 JRUC-5-MO $14.73 JRTN-5-MO $17.65 JRTA-5-MO $ /4 3 JRUC-4-MO $14.73 JRTN-4-MO $17.65 JRTA-4-MO $ /4 3 JRUC-3-MO $14.73 JRTN-3-MO $17.65 JRTA-3-MO $ / /4 3 JRUC-7/32-MO $14.73 JRTN-7/32-MO $17.65 JRTA-7/32-MO $ /4 3 JRUC-2-MO $14.73 JRTN-2-MO $17.65 JRTA-2-MO $ /4 3 JRUC-1-MO $14.73 JRTN-1-MO $17.65 JRTA-1-MO $18.67 A /4 JRUC-A-MO $17.35 JRTN-A-MO $20.27 JRTA-A-MO $ / /4 JRUC-15/64-MO $17.35 JRTN-15/64-MO $20.27 JRTA-15/64-MO $ /4 JRUC--MO $18.40 JRTN--MO $21.32 JRTA--MO $22.34 C /4 JRUC-C-MO $18.40 JRTN-C-MO $21.32 JRTA-C-MO $22.34 D /4 JRUC-D-MO $18.40 JRTN-D-MO $21.32 JRTA-D-MO $ / /4 JRUC-1/4-MO $18.05 JRTN-1/4-MO $20.97 JRTA-1/4-MO $21.99 E /4 JRUC-E-MO $18.40 JRTN-E-MO $20.97 JRTA-E-MO $22.34 F /4 JRUC-F-MO $18.40 JRTN-F-MO $21.32 JRTA-F-MO $22.34 G /4 3-1/2 JRUC-G-MO $21.56 JRTN-G-MO $25.50 JRTA-G-MO $ / /4 3-1/2 JRUC-17/64-MO $21.56 JRTN-17/64-MO $25.50 JRTA-17/64-MO $28.12 H /4 3-1/2 JRUC-H-MO $22.26 JRTN-H-MO $26.20 JRTA-H-MO $28.82 I /4 3-1/2 JRUC-I-MO $22.26 JRTN-I-MO $26.20 JRTA-I-MO $28.82 J /4 3-1/2 JRUC-J-MO $22.26 JRTN-J-MO $26.20 JRTA-J-MO $28.82 K /4 3-1/2 JRUC-K-MO $22.26 JRTN-K-MO $26.20 JRTA-K-MO $ / /4 3-1/2 JRUC-9/32-MO $22.26 JRTN-9/32-MO $26.20 JRTA-9/32-MO $28.82 L /4 3-1/2 JRUC-L-MO $22.26 JRTN-L-MO $26.20 JRTA-L-MO $28.82 M /8 3-3/4 JRUC-M-MO $26.88 JRTN-M-MO $30.82 JRTA-M-MO $ / /8 3-3/4 JRUC-19/64-MO $26.88 JRTN-19/64-MO $30.82 JRTA-19/64-MO $33.44 N /8 3-3/4 JRUC-N-MO $27.23 JRTN-N-MO $31.17 JRTA-N-MO $ / /8 3-3/4 JRUC-5/16-MO $26.88 JRTN-5/16-MO $30.82 JRTA-5/16-MO $33.44 O /8 3-3/4 JRUC-O-MO $27.23 JRTN-O-MO $31.17 JRTA-O-MO $33.79 P /8 3-3/4 JRUC-P-MO $27.23 JRTN-P-MO $31.17 JRTA-P-MO $ / /2 4 JRUC-21/64-MO $30.24 JRTN-21/64-MO $34.18 JRTA-21/64-MO $36.80 Q /2 4 JRUC-Q-MO $31.29 JRTN-Q-MO $35.23 JRTA-Q-MO $37.85 R /2 4 JRUC-R-MO $31.29 JRTN-R-MO $35.23 JRTA-R-MO $ / /2 4 JRUC-11/32-MO $30.59 JRTN-11/32-MO $34.53 JRTA-11/32-MO $37.15 S /2 4 JRUC-S-MO $31.29 JRTN-S-MO $35.23 JRTA-S-MO $37.85 T /4 4-1/4 JRUC-T-MO $36.84 JRTN-T-MO $43.26 JRTA-T-MO $ / /4 4-1/4 JRUC-23/64-MO $36.14 JRTN-23/64-MO $42.56 JRTA-23/64-MO $42.71 U /4 4-1/4 JRUC-U-MO $39.29 JRTN-U-MO $45.71 JRTA-U-MO $ / /4 4-1/4 JRUC-3/8-MO $38.59 JRTN-3/8-MO $45.01 JRTA-3/8-MO $45.16 V /4 4-1/4 JRUC-V-MO $39.29 JRTN-V-MO $45.71 JRTA-V-MO $45.86 W /8 4-1/2 JRUC-W-MO $49.98 JRTN-W-MO $57.71 JRTA-W-MO $ / /8 4-1/2 JRUC-25/64-MO $46.57 JRTN-25/64-MO $53.57 JRTA-25/64-MO $57.39 X /8 4-1/2 JRUC-X-MO $51.03 JRTN-X-MO $58.76 JRTA-X-MO $60.95 Y /8 4-1/2 JRUC-Y-MO $51.03 JRTN-Y-MO $58.76 JRTA-Y-MO $ / /8 4-1/2 JRUC-13/32-MO $47.62 JRTN-13/32-MO $54.62 JRTA-13/32-MO $58.44 Z /8 4-1/2 JRUC-Z-MO $53.13 JRTN-Z-MO $60.86 JRTA-Z-MO $ / /8 4-1/2 JRUC-27/64-MO $48.93 JRTN-27/64-MO $55.93 JRTA-27/64-MO $ / /8 4-1/2 JRUC-7/16-MO $51.03 JRTN-7/16-MO $59.46 JRTA-7/16-MO $ / /4 JRUC-29/64-MO $65.73 JRTN-29/64-MO $74.16 JRTA-29/64-MO $ / /4 JRUC-15/32-MO $66.78 JRTN-15/32-MO $75.21 JRTA-15/32-MO $ / /4 JRUC-31/64-MO $67.04 JRTN-31/64-MO $75.47 JRTA-31/64-MO $ / /4 JRUC-1/2-MO $67.83 JRTN-1/2-MO $76.26 JRTA-1/2-MO $ Master Catalog 437 C CARIDE INSERTS DEURRING

170 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD PARAOLIC JOER LENGTH DRILLS JOER LENGTH DRILLS HSS-WIDE LAND PARAOLIC FLUTE 135 Self-Centering Split Point Fractional right TiN Coated Dec.Equiv Flute Length Master Catalog Pkg Qty 1/ /8 1-7/8 12 PTD $2.21 PTD $4.16 5/ PTD $2.25 PTD $4.23 3/ /4 2-1/4 12 PTD $2.21 PTD $4.16 7/ /2 2-5/8 12 PTD $2.46 PTD $4.68 1/ /8 2-3/4 12 PTD $2.48 PTD $4.67 9/ /4 2-7/8 12 PTD $2.58 PTD $4.95 5/ /8 12 PTD $2.61 PTD $ / /8 3-1/4 12 PTD $2.96 PTD $5.65 3/ /16 3-1/2 12 PTD $3.17 PTD $ / /16 3-5/8 12 PTD $3.61 PTD $7.15 7/ /2 3-3/4 12 PTD $3.99 PTD $ / /8 3-7/8 12 PTD $4.48 PTD $8.55 1/ / PTD $4.60 PTD $ / /8 4-1/8 12 PTD $5.50 PTD $ / /16 4-1/4 12 PTD $5.50 PTD $ / /16 4-3/8 12 PTD $6.65 PTD $ / /16 4-1/2 6 PTD $7.08 PTD $ / /16 4-5/8 6 PTD $8.08 PTD $ / /16 4-3/4 6 PTD $8.83 PTD $ / /2 4-7/8 6 PTD $10.28 PTD $ / /8 5 6 PTD $10.08 PTD $ / /4 5-1/8 6 PTD $11.83 PTD $ / /8 5-1/4 6 PTD $11.78 PTD $ / /16 5-3/8 6 PTD $13.50 PTD $ / /16 5-1/2 6 PTD $13.55 PTD $ / /16 5-5/8 6 PTD $15.93 PTD $ / /16 5-3/4 6 PTD $16.33 PTD $ / /8 5-7/8 6 PTD $17.73 PTD $ / /2 6 6 PTD $17.15 PTD $32.95 Additional Sizes Available. Please Call For More Information. Wire Sizes right TiN Coated Dec. Flute Pkg /8 3-7/8 12 PTD $4.83 PTD $ /8 3-7/8 12 PTD $4.83 PTD $ /2 3-3/4 12 PTD $4.37 PTD $ /2 3-3/4 12 PTD $4.37 PTD $ /2 3-3/4 12 PTD $4.37 PTD $ /2 3-3/4 12 PTD $4.37 PTD $ /16 3-5/8 12 PTD $3.91 PTD $ /16 3-5/8 12 PTD $3.91 PTD $ /16 3-5/8 12 PTD $3.91 PTD $ /16 3-5/8 12 PTD $3.91 PTD $ /16 3-1/2 12 PTD $3.60 PTD $ /16 3-1/2 12 PTD $3.60 PTD $ /16 3-1/2 12 PTD $3.53 PTD $ /16 3-3/8 12 PTD $3.53 PTD $ /16 3-3/8 12 PTD $3.53 PTD $ /16 3-3/8 12 PTD $3.53 PTD $ /16 3-3/8 12 PTD $3.53 PTD $ /8 3-1/4 12 PTD $2.92 PTD $ /8 3-1/4 12 PTD $2.92 PTD $ /8 3-1/4 12 PTD $2.92 PTD $ /8 3-1/4 12 PTD $2.71 PTD $ /8 12 PTD $2.71 PTD $ /8 12 PTD $2.64 PTD $ /8 12 PTD $2.64 PTD $ / PTD $2.61 PTD $4.97 Additional Sizes Available. Please Call For More Information. C

171 SCREW MACHINE LENGTH STU DRILLS-HSS/COALT SCREW MACHINE DRILLS High Speed Steel 135 Self-Centering Split Point Heavy Duty C COMPLETE LINE AVAILALE! We offer the complete line of Morse Cutting Tools! Drills-Stub, Jobber, Carbide, Automotive, Left Hand, S&D Taps- ShearTaps, Hand Taps, High Performance Taps Reamers End Mills Countersinks, Center Drills & Spotting Drills Please Call For More Information! WORK STOP. Fractional Sizes Dec Equiv lack Oxide 135 Split Point Cobalt HSS 135 Split Point 1/ /8 PTD-1/16-SHS $1.22 PTD-1/16-SCGS $1.44 5/ /16 PTD-5/64-SHS $1.23 PTD-5/64-SCGS $1.44 3/ /4 PTD-3/32-SHS $1.20 PTD-3/32-SCGS $1.44 7/ /16 PTD-7/64-SHS $1.23 PTD-7/64-SCGS $1.63 1/ /8 PTD-1/8-SHS $1.17 PTD-1/8-SCGS $1.87 9/ /16 PTD-9/64-SHS $1.25 PTD-9/64-SCGS $1.89 5/ /16 PTD-5/32-SHS $1.35 PTD-5/32-SCGS $ / /8 PTD-11/64-SHS $1.44 PTD-11/64-SCGS $2.33 3/ /16 PTD-3/16-SHS $1.54 PTD-3/16-SCGS $ / /4 PTD-13/64-SHS $1.64 PTD-13/64-SCGS $3.11 7/ /8 PTD-7/32-SHS $1.96 PTD-7/32-SCGS $ / /16 PTD-15/64-SHS $2.01 PTD-15/64-SCGS $3.81 1/ /2 PTD-1/4-SHS $2.20 PTD-1/4-SCGS $ / /8 PTD-17/64-SHS $2.54 PTD-17/64-SCGS $4.49 9/ /16 PTD-9/32-SHS $2.73 PTD-9/32-SCGS $ / /4 PTD-19/64-SHS $3.02 PTD-19/64-SCGS $5.67 5/ /16 PTD-5/16-SHS $3.21 PTD-5/16-SCGS $ / /16 PTD-21/64-SHS $3.58 PTD-21/64-SCGS $ / PTD-11/32-SHS $4.01 PTD-11/32-SCGS $ / /16 PTD-23/64-SHS $4.64 PTD-23/64-SCGS $8.42 3/ /8 PTD-3/8-SHS $4.82 PTD-3/8-SCGS $ / /4 PTD-25/64-SHS $5.49 PTD-25/64-SCGS $ / /16 PTD-13/32-SHS $5.63 PTD-13/32-SCGS $ / /8 PTD-27/64-SHS $6.26 PTD-27/64-SCGS $ / /16 PTD-7/16-SHS $6.28 PTD-7/16-SCGS $ / /16 PTD-29/64-SHS $7.54 PTD-29/64-SCGS $ / /8 PTD-15/32-SHS $8.03 PTD-15/32-SCGS $ / /16 PTD-31/64-SHS $8.26 PTD-31/64-SCGS $ / /4 PTD-1/2-SHS $8.08 PTD-1/2-SCGS $ / /8 - - PTD-33/64-SCGS $ / /8 - - PTD-17/32-SCGS $ / PTD-35/64-SCGS $ / PTD-9/16-SCGS $ / /8 - - PTD-37/64-SCGS $ / /8 - - PTD-19/32-SCGS $ / /4 - - PTD-39/64-SCGS $ / /4 - - PTD-5/8-SCGS $ / /2 - - PTD-41/64-SCGS $ / /2 - - PTD-21/32-SCGS $ / /8 - - PTD-43/64-SCGS $ / /8 - - PTD-11/16-SCGS $ / /4 - - PTD-45/64-SCGS $ / /4 - - PTD-23/32-SCGS $ / PTD-47/64-SCGS $ / PTD-3/4-SCGS $59.85 Adjustable Precision-Gage lengths up to 5-1/2 long holding +/-.005 Save Money! No more fixed length dedicated shop-made front collet stops for each job Versatile-For use on CNC or manual lathes whether you are running a bar manually or using a bar puller. Can also be used on mill vises! Consistency-Unique design incorporates self-centering, unobstructed viewing and contrasting colors to give user confidence by feeling and seeing that the dimension is being controlled Made in Stop-Loc STOP-LOC Chuck/Collet/Work Stop Inch Style # STOPLOC $16.95 each With Metric/Thous # STOPLOC-MM $22.95 each Pat.Pend Master Catalog 439 CARIDE INSERTS DEURRING

172 CHUCK JAWS LATHE WORKHOLDING SCREW MACHINE/STU LENGTH STU DRILLS SCREW MACHINE DRILLS Wire Sizes-HSS & Cobalt 135 Self-Centering Split Point Heavy Duty C MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD. Wire Sizes Dec Equiv lack Oxide 135 Split Point Cobalt HSS 135 Split Point /16 PTD-1-SHS $2.12 PTD-1-SCGS $ /16 PTD-2-SHS $2.12 PTD-2-SCGS $ /8 PTD-3-SHS $1.99 PTD-3-SCGS $ /8 PTD-4-SHS $1.99 PTD-4-SCGS $ /8 PTD-5-SHS $1.99 PTD-5-SCGS $ /8 PTD-6-SHS $1.99 PTD-6-SCGS $ /4 PTD-7-SHS $1.65 PTD-7-SCGS $ /4 PTD-8-SHS $1.66 PTD-8-SCGS $ /4 PTD-9-SHS $1.66 PTD-9-SCGS $ /4 PTD-10-SHS $1.65 PTD-10-SCGS $ /4 PTD-11-SHS $1.65 PTD-11-SCGS $ /4 PTD-12-SHS $1.66 PTD-12-SCGS $ /16 PTD-13-SHS $1.66 PTD-13-SCGS $ /16 PTD-14-SHS $1.66 PTD-14-SCGS $ /16 PTD-15-SHS $1.66 PTD-15-SCGS $ /16 PTD-16-SHS $1.66 PTD-16-SCGS $ /16 PTD-17-SHS $1.66 PTD-17-SCGS $ /8 PTD-18-SHS $1.39 PTD-18-SCGS $ /8 PTD-19-SHS $1.39 PTD-19-SCGS $ /8 PTD-20-SHS $1.39 PTD-20-SCGS $ /8 PTD-21-SHS $1.34 PTD-21-SCGS $ /8 PTD-22-SHS $1.34 PTD-22-SCGS $ /16 PTD-23-SHS $1.34 PTD-23-SCGS $ /16 PTD-24-SHS $1.34 PTD-24-SCGS $ /16 PTD-25-SHS $1.32 PTD-25-SCGS $ /16 PTD-26-SHS $1.32 PTD-26-SCGS $ /16 PTD-27-SHS $1.32 PTD-27-SCGS $ /16 PTD-28-SHS $1.19 PTD-28-SCGS $ /16 PTD-29-SHS $1.19 PTD-29-SCGS $ /16 PTD-30-SHS $1.19 PTD-30-SCGS $1.76 SCREW MACHINE DRILLS Letter Sizes-HSS & Cobalt 135 Self-Centering Split Point Heavy Duty Wire Sizes Master Catalog. Letter Sizes Dec Equiv. Dec Equiv lack Oxide 135 Split Point Cobalt HSS 135 Split Point /8 PTD-31-SHS $1.19 PTD-31-SCGS $ /8 PTD-32-SHS $1.19 PTD-32-SCGS $ /8 PTD-33-SHS $1.19 PTD-33-SCGS $ /8 PTD-34-SHS $1.19 PTD-34-SCGS $ /8 PTD-35-SHS $1.19 PTD-35-SCGS $ /16 PTD-36-SHS $1.19 PTD-36-SCGS $ /16 PTD-37-SHS $1.19 PTD-37-SCGS $ /16 PTD-38-SHS $1.19 PTD-38-SCGS $ /16 PTD-39-SHS $1.19 PTD-39-SCGS $ /16 PTD-40-SHS $1.19 PTD-40-SCGS $ /16 PTD-41-SHS $1.19 PTD-41-SCGS $ /4 PTD-42-SHS $1.19 PTD-42-SCGS $ /4 PTD-43-SHS $1.19 PTD-43-SCGS $ /4 PTD-44-SHS $1.19 PTD-44-SCGS $ /4 PTD-45-SHS $1.19 PTD-45-SCGS $ /4 PTD-46-SHS $1.19 PTD-46-SCGS $ /16 PTD-47-SHS $1.19 PTD-47-SCGS $ /16 PTD-48-SHS $1.19 PTD-48-SCGS $ /16 PTD-49-SHS $1.19 PTD-49-SCGS $ /16 PTD-50-SHS $1.19 PTD-50-SCGS $ /16 PTD-51-SHS $1.19 PTD-51-SCGS $ /16 PTD-52-SHS $1.19 PTD-52-SCGS $ /8 PTD-53-SHS $1.19 PTD-53-SCGS $ /8 PTD-54-SHS $1.19 PTD-54-SCGS $ /8 PTD-55-SHS $1.19 PTD-55-SCGS $ /8 PTD-56-SHS $1.19 PTD-56-SCGS $ /8 PTD-57-SHS $1.19 PTD-57-SCGS $ /8 PTD-58-SHS $1.19 PTD-58-SCGS $ /8 PTD-59-SHS $1.19 PTD-59-SCGS $ /8 PTD-60-SHS $1.19 PTD-60-SCGS $1.77 lack Oxide 135 Split Point Cobalt HSS 135 Split Point A /16 PTD-A-SHS $2.51 PTD-A-SCGS $ /2 PTD--SHS $2.51 PTD--SCGS $4.77 C /2 PTD-C-SHS $2.51 PTD-C-SCGS $4.75 D /2 PTD-D-SHS $2.51 PTD-D-SCGS $4.77 E /2 PTD-E-SHS $2.67 PTD-E-SCGS $4.35 F /8 PTD-F-SHS $2.76 PTD-F-SCGS $5.06 G /8 PTD-G-SHS $2.95 PTD-G-SCGS $5.09 H /16 PTD-H-SHS $2.95 PTD-H-SCGS $5.36 I /16 PTD-I-SHS $2.95 PTD-I-SCGS $5.36 J /16 PTD-J-SHS $3.15 PTD-J-SCGS $5.36 K /16 PTD-K-SHS $3.41 PTD-K-SCGS $5.36 L /4 PTD-L-SHS $3.41 PTD-L-SCGS $6.35 M /4 PTD-M-SHS $3.70 PTD-M-SCGS $6.35 N /16 PTD-N-SHS $3.70 PTD-N-SCGS $6.82 O /16 PTD-O-SHS $3.74 PTD-O-SCGS $7.58 P /16 PTD-P-SHS $4.19 PTD-P-SCGS $7.58 Q PTD-Q-SHS $4.19 PTD-Q-SCGS $8.19 R PTD-R-SHS $4.24 PTD-R-SCGS $8.19 S /16 PTD-S-SHS $4.82 PTD-S-SCGS $10.17 T /16 PTD-T-SHS $5.58 PTD-T-SCGS $10.17 U /8 PTD-U-SHS $5.58 PTD-U-SCGS $10.17 V /4 PTD-V-SHS $5.99 PTD-V-SCGS $11.27 W /4 PTD-W-SHS $6.28 PTD-W-SCGS $11.27 X /16 PTD-X-SHS $7.27 PTD-X-SCGS $11.27 Y /16 PTD-Y-SHS $8.62 PTD-Y-SCGS $11.27 Z /8 PTD-Z-SHS $8.62 PTD-Z-SCGS $12.94

173 SOLID CARIDE DRILLS-STU LENGTH MACHINE SCREW/STU DRILLS SOLID CARIDE FEATURES: Designed for stainless steel, tool steel, titanium and nickel alloys Made from premium submicron carbide with 10% cobalt 15 helix, right hand spiral, right hand cut 135 drill point Made in Full Line Available! Please call for more information. Size Dec. LOC Uncoated TiAlN Coated Uncoated TiAlN Coated Size Dec. LOC 1/ /2 1-1/2 SRUC-1/32-MO $7.43 SRTA-1/32-MO $ /16 2-1/4 SRUC-10-MO $13.67 SRTA-10-MO $ /2 1-1/2 SRUC-56-MO $7.18 SRTA-56-MO $ /16 2-1/4 SRUC-9-MO $13.67 SRTA-9-MO $ / /2 1-1/2 SRUC-3/64-MO $9.10 SRTA-3/64-MO $ /16 2-1/4 SRUC-8-MO $13.67 SRTA-8-MO $ /2 1-1/2 SRUC-55-MO $7.18 SRTA-55-MO $ /16 2-1/4 SRUC-7-MO $13.67 SRTA-7-MO $ /2 1-1/2 SRUC-54-MO $7.18 SRTA-54-MO $ / /16 2-1/4 SRUC-13/64-MO $13.67 SRTA-13/64-MO $ /2 1-1/2 SRUC-53-MO $7.18 SRTA-53-MO $ /4 2-3/8 SRUC-6-MO $14.83 SRTA-6-MO $ / /8 1-5/8 SRUC-1/16-MO $7.26 SRTA-1/16-MO $ /4 2-3/8 SRUC-5-MO $14.83 SRTA-5-MO $ / /16 SRUC-52-MO $7.08 SRTA-52-MO $ /4 2-3/8 SRUC-4-MO $14.83 SRTA-4-MO $ / /16 SRUC-51-MO $7.08 SRTA-51-MO $ /4 2-3/8 SRUC-3-MO $15.57 SRTA-3-MO $ / /16 SRUC-50-MO $7.08 SRTA-50-MO $9.95 7/ /4 2-3/8 SRUC-7/32-MO $14.83 SRTA-7/32-MO $ / /16 SRUC-49-MO $7.08 SRTA-49-MO $ /16 2-7/16 SRUC-2-MO $16.44 SRTA-2-MO $ / /16 SRUC-48-MO $7.08 SRTA-48-MO $ /16 2-7/16 SRUC-1-MO $16.81 SRTA-1-MO $ / / /16 SRUC-5/64-MO $7.26 SRTA-5/64-MO $10.30 A /16 2-7/16 SRUC-A-MO $16.81 SRTA-A-MO $ /4 1-3/4 SRUC-47-MO $7.43 SRTA-47-MO $ / /16 2-7/16 SRUC-15/64-MO $16.81 SRTA-15/64-MO $ /4 1-3/4 SRUC-46-MO $7.43 SRTA-46-MO $ /8 2-1/2 SRUC--MO $19.41 SRTA--MO $ /4 1-3/4 SRUC-45-MO $7.43 SRTA-45-MO $10.30 C /8 2-1/2 SRUC-C-MO $19.41 SRTA-C-MO $ /4 1-3/4 SRUC-44-MO $7.43 SRTA-44-MO $10.30 D /8 2-1/2 SRUC-D-MO $19.41 SRTA-D-MO $ /4 1-3/4 SRUC-43-MO $7.43 SRTA-43-MO $ / /8 2-1/2 SRUC-1/4-MO $18.36 SRTA-1/4-MO $ /4 1-3/4 SRUC-42-MO $7.43 SRTA-42-MO $10.30 E /8 2-1/2 SRUC-E-MO $19.41 SRTA-E-MO $ / /4 1-3/4 SRUC-3/32-MO $7.61 SRTA-3/32-MO $10.47 F /16 2-5/8 SRUC-F-MO $21.33 SRTA-F-MO $ / /16 SRUC-41-MO $7.76 SRTA-41-MO $10.62 G /16 2-5/8 SRUC-G-MO $21.33 SRTA-G-MO $ / /16 SRUC-40-MO $7.76 SRTA-40-MO $ / /16 2-5/8 SRUC-17/64-MO $21.33 SRTA-17/64-MO $ / /16 SRUC-39-MO $7.76 SRTA-39-MO $10.62 H /2 2-11/16 SRUC-H-MO $24.00 SRTA-H-MO $ / /16 SRUC-38-MO $7.76 SRTA-38-MO $10.62 I /2 2-11/16 SRUC-I-MO $24.00 SRTA-I-MO $ / /16 SRUC-37-MO $7.76 SRTA-37-MO $10.62 J /2 2-11/16 SRUC-J-MO $24.00 SRTA-J-MO $ / /16 SRUC-36-MO $7.76 SRTA-36-MO $10.62 K /2 2-11/16 SRUC-K-MO $25.89 SRTA-K-MO $ / / /16 SRUC-7/64-MO $7.93 SRTA-7/64-MO $ / /2 2-11/16 SRUC-9/32-MO $24.00 SRTA-9/32-MO $ /8 1-7/8 SRUC-35-MO $7.78 SRTA-35-MO $10.65 L /16 2-3/4 SRUC-L-MO $26.71 SRTA-L-MO $ /8 1-7/8 SRUC-34-MO $7.78 SRTA-34-MO $10.65 M /16 2-3/4 SRUC-M-MO $26.71 SRTA-M-MO $ /8 1-7/8 SRUC-33-MO $7.78 SRTA-33-MO $ / /16 2-3/4 SRUC-19/64-MO $24.82 SRTA-19/64-MO $ /8 1-7/8 SRUC-32-MO $7.78 SRTA-32-MO $10.65 N /8 2-13/16 SRUC-N-MO $27.99 SRTA-N-MO $ /8 1-7/8 SRUC-31-MO $7.78 SRTA-31-MO $ / /8 2-13/16 SRUC-5/16-MO $26.10 SRTA-5/16-MO $ / /8 1-7/8 SRUC-1/8-MO $7.96 SRTA-1/8-MO $10.82 O / /16 SRUC-O-MO $29.32 SRTA-O-MO $ / /16 SRUC-30-MO $8.91 SRTA-30-MO $11.25 P / /16 SRUC-P-MO $29.32 SRTA-P-MO $ / /16 SRUC-29-MO $8.91 SRTA-29-MO $ / / /16 SRUC-21/64-MO $26.90 SRTA-21/64-MO $ / /16 SRUC-28-MO $8.91 SRTA-28-MO $11.78 Q /16 3 SRUC-Q-MO $33.29 SRTA-Q-MO $ / / /16 SRUC-9/64-MO $8.91 SRTA-9/64-MO $11.78 R /16 3 SRUC-R-MO $33.29 SRTA-R-MO $ /16 SRUC-27-MO $9.59 SRTA-27-MO $ / /16 3 SRUC-11/32-MO $31.26 SRTA-11/32-MO $ /16 SRUC-26-MO $9.59 SRTA-26-MO $13.09 S /4 3-1/16 SRUC-S-MO $33.73 SRTA-S-MO $ /16 SRUC-25-MO $9.59 SRTA-25-MO $13.09 T /4 3-1/16 SRUC-T-MO $33.73 SRTA-T-MO $ /16 SRUC-24-MO $9.59 SRTA-24-MO $ / /4 3-1/16 SRUC-23/64-MO $30.65 SRTA-23/64-MO $ /16 SRUC-23-MO $9.59 SRTA-23-MO $13.09 U /16 3-1/8 SRUC-U-MO $40.67 SRTA-U-MO $ / /16 SRUC-5/32-MO $9.59 SRTA-5/32-MO $ / /16 3-1/8 SRUC-3/8-MO $37.10 SRTA-3/8-MO $ /16 2-1/8 SRUC-22-MO $10.12 SRTA-22-MO $13.62 V /8 3-1/4 SRUC-V-MO $42.98 SRTA-V-MO $ /16 2-1/8 SRUC-21-MO $10.12 SRTA-21-MO $13.62 W /8 3-1/4 SRUC-W-MO $42.98 SRTA-W-MO $ /16 2-1/8 SRUC-20-MO $10.82 SRTA-20-MO $ / /8 3-1/4 SRUC-25/64-MO $39.94 SRTA-25/64-MO $ /16 2-1/8 SRUC-19-MO $11.87 SRTA-19-MO $15.37 X /16 3-5/16 SRUC-X-MO $47.56 SRTA-X-MO $ /16 2-1/8 SRUC-18-MO $11.87 SRTA-18-MO $15.37 Y /16 3-5/16 SRUC-Y-MO $47.56 SRTA-Y-MO $ / /16 2-1/8 SRUC-11/64-MO $10.12 SRTA-11/64-MO $ / /16 3-5/16 SRUC-13/32-MO $46.54 SRTA-13/32-MO $ /8 2-3/16 SRUC-17-MO $12.58 SRTA-17-MO $16.08 Z /8 SRUC-Z-MO $51.84 SRTA-Z-MO $ /8 2-3/16 SRUC-16-MO $13.01 SRTA-16-MO $ / /8 SRUC-27/64-MO $50.63 SRTA-27/64-MO $ /8 2-3/16 SRUC-15-MO $13.01 SRTA-15-MO $ / /16 3-7/16 SRUC-7/16-MO $55.56 SRTA-7/16-MO $ /8 2-3/16 SRUC-14-MO $13.01 SRTA-14-MO $ / /8 3-9/16 SRUC-29/64-MO $61.06 SRTA-29/64-MO $ /8 2-3/16 SRUC-13-MO $13.01 SRTA-13-MO $ / /8 3-5/8 SRUC-15/32-MO $62.58 SRTA-15/32-MO $ / /8 2-3/16 SRUC-3/16-MO $11.18 SRTA-3/16-MO $ / / /16 SRUC-31/64-MO $63.21 SRTA-31/64-MO $ /16 2-1/4 SRUC-12-MO $13.67 SRTA-12-MO $ / /4 3-3/4 SRUC-1/2-MO $67.12 SRTA-1/2-MO $ /16 2-1/4 SRUC-11-MO $13.67 SRTA-11-MO $ Master Catalog 441 C CARIDE INSERTS DEURRING

174 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD PARAOLIC/EXTRA LENGTH DRILLS SCREW MACHINE DRILLS WIDE LAND PARAOLIC FLUTE High Speed Steel 135 Self-Centering Split Point EXTRA LENGTH DRILLS HSS, Straight, 118 Point Fractional right TiN Coated Master Catalog Dec. Equiv Flute Length Pkg Qty 1/ /8 1-5/8 12 PTD $2.21 PTD $4.12 5/ / /16 12 PTD $2.21 PTD $4.12 3/ /4 1-3/4 12 PTD $2.21 PTD $4.12 7/ / /16 12 PTD $2.43 PTD $4.60 1/ /8 1-7/8 12 PTD $2.46 PTD $4.69 9/ / /16 12 PTD $2.56 PTD $4.92 5/ /16 12 PTD $2.59 PTD $ / /16 2-1/8 12 PTD $2.90 PTD $5.50 3/ /8 2-3/16 12 PTD $3.13 PTD $ / /16 2-1/4 12 PTD $3.59 PTD $7.10 7/ /4 2-3/8 12 PTD $3.96 PTD $ / /16 2-7/16 12 PTD $4.40 PTD $8.38 1/ /8 2-1/2 12 PTD $4.45 PTD $ / /16 2-5/8 12 PTD $5.28 PTD $ / /2 2-11/16 12 PTD $5.30 PTD $ / /16 2-3/4 12 PTD $6.35 PTD $ / /8 2-13/16 6 PTD $6.53 PTD $ / / /16 6 PTD $7.45 PTD $ / / PTD $8.03 PTD $ / /4 3-1/16 6 PTD $9.25 PTD $ / /16 3-1/8 6 PTD $8.98 PTD $ / /8 3-1/4 6 PTD $10.53 PTD $ / /16 3-5/16 6 PTD $10.50 PTD $ / /8 6 PTD $12.05 PTD $ / /16 3-7/16 6 PTD $12.05 PTD $ / /8 3-9/16 6 PTD $13.98 PTD $ / /8 3-5/8 6 PTD $14.33 PTD $ / /16 3-3/4 6 PTD $15.55 PTD $ / /4 3-3/4 6 PTD $15.30 PTD $29.30 Ideal for deep hole or long reach drilling applications Cobalt and extended lengths up to 48 with 5-1/2 flute length also available d per each 6" w/ 4" Flute Length 8" w/5-1/2" Flute Length (cont.) 10" w/7-1/2 Flute Length (cont.) 12" w/9" Flute Length (cont.). Dec.. Dec.. Dec.. Dec. 1/ MH-208A-1/16 $ / MH /64 $ / MH-208-1/4 $ / MH-212-7/32 $ / MH-208A-5/64 $7.69 3/ MH-208-3/8 $ / MH /64 $ / MH /64 $ / MH-208A-3/32 $ / MH /64 $ / MH-208-9/32 $ / MH-212-1/4 $ / MH-208A-7/64 $ / MH /32 $ / MH /64 $ / MH /64 $ / MH-208A-1/8 $ / MH /64 $ / MH-208-5/16 $ / MH-212-9/32 $ / MH-208A-9/64 $6.24 7/ MH-208-7/16 $ / MH /64 $ / MH /64 $ / MH-208A-5/32 $ / MH /64 $ / MH /32 $ / MH-212-5/16 $ / MH-208A-11/64 $ / MH /32 $ / MH /64 $ / MH /64 $ / MH-208A-3/16 $ / MH /64 $ / MH-208-3/8 $ / MH /32 $ " w/ 5-1/2" Flute Length 1/ MH-208-1/2 $ / MH /64 $ / MH /64 $ Dec. 9" w/ 6-1/2" Flute Length 13/ MH /32 $ / MH-212-3/8 $ / MH-208-3/32 $ Dec. 27/ MH /64 $ / MH /64 $ / MH-208-7/64 $ / MH /64 $ MM.4331 MH MM $ / MH /31 $ / MH-208-1/8 $ / MH-209-7/16 $ / MH-208-7/16 $ / MH /64 $ / MH-208-9/64 $ / MH /64 $ / MH /64 $ / MH-212-7/16 $ / MH-208-5/32 $ / MH /32 $ / MH /32 $ / MH /64 $ / MH /64 $ / MH /64 $ / MH /64 $ / MH /32 $ / MH-208-3/16 $ / MH-209-1/2 $ / MH-208-1/2 $ / MH /64 $ / MH /64 $ / MH /32 $ / MH /32 $ / MH-212-1/2 $ / MH-208-7/32 $ " w/ 7-1/2 Flute Length 9/ MH-208-9/16 $ / MH /64 $ / MH /64 $ Dec. 12" w/ 9" Flute Length 17/ MH /32 $ / MH-208-1/4 $ / MH-208-1/8 $ Dec. 35/ MH /64 $40.33 F.2570 MH-208-F $ / MH-208-9/64 $ / MH-212-7/64 $ / MH-212-9/16 $ / MH /64 $ / MH-208-5/32 $ / MH-212-1/8 $ / MH /64 $ / MH-208-9/32 $ / MH /64 $ / MH-212-9/64 $ / MH /32 $ / MH /64 $ / MH-208-3/16 $ / MH-212-5/32 $ / MH-212-5/8 $ / MH-208-5/16 $ / MH /64 $ / MH /64 $ / MH-212-3/4 $ / MH /64 $ / MH-208-7/32 $ / MH-212-3/16 $ / MH-212-7/8 $ / MH /32 $ / MH /64 $ / MH /64 $19.80 C

175 EXTRA LENGTH DRILLS EXTRA LENGTH DRILLS High Speed Steel 135 Self-Centering Split Point 6 Aircraft Extension Longer Drills Available! Up To 48! Call For More Information Wire Sizes lack Oxide Wire Sizes (cont.) lack Oxide. Dec Equiv Flute Len AIRCRAFT EXTENSION DRILLS High Speed Steel-lack Oxide 135 Self-Centering Split Point 6 & 12 NEW ITEM! TMX Features: 135 Self-Centering Split Point HSSlack Oxide Sold In Package Quantities- 1/16 to 7/32: 10 per pack 15/64 to 11/32: 5 per pack Over 23/64 : 1 per pack TMX Drills Sold In Package Quantities Pkg Qty. Dec Equiv Flute Len Master Catalog 443 Pkg Qty /8 12 PTD $ /8 12 PTD $ /8 12 PTD $ /8 12 PTD $ /2 12 PTD $ /2 12 PTD $ /2 12 PTD $ /2 12 PTD $ /2 12 PTD $ /2 12 PTD $ /2 12 PTD $ /16 12 PTD $ /16 12 PTD $ /16 12 PTD $ /16 12 PTD $ /16 12 PTD $ /16 12 PTD $ /8 12 PTD $ /16 12 PTD $ /8 12 PTD $ /16 12 PTD $ /8 12 PTD $ /16 12 PTD $ /4 12 PTD $ /16 12 PTD $ /4 12 PTD $ /16 12 PTD $ /8 12 PTD $ /16 12 PTD $ /8 12 PTD $ /16 12 PTD $ /8 12 PTD $ /16 12 PTD $ PTD $ /8 12 PTD $ PTD $ /8 12 PTD $ PTD $ /8 12 PTD $ PTD $ /8 12 PTD $ PTD $ PTD $ /8 12 PTD $ PTD $ /8 12 PTD $ PTD $ /8 12 PTD $ /8 12 PTD $ /8 12 PTD $ /8 12 PTD $ /4 12 PTD $ /8 12 PTD $ /4 12 PTD $ /4 12 PTD $ /16 12 PTD $ /4 12 PTD $ /16 12 PTD $ /8 12 PTD $ /16 12 PTD $7.43 Dec. Equiv. Flute Length Pkg Qty Split Point Split Point 1/ /8 10 TMX $1.07 TMX $1.93 5/ TMX $1.07 TMX $1.93 3/ /4 10 TMX $1.20 TMX $2.16 7/ /2 10 TMX $1.28 TMX $2.30 1/ /8 10 TMX $1.47 TMX $2.65 9/ /4 10 TMX $1.62 TMX $2.92 5/ TMX $1.85 TMX $ / /8 10 TMX $1.98 TMX $3.56 3/ /16 10 TMX $2.04 TMX $ / /16 10 TMX $2.25 TMX $4.05 7/ /2 10 TMX $2.45 TMX $ / /8 5 TMX $2.60 TMX $4.68 1/ /4 5 TMX $2.75 TMX $ / /8 5 TMX $2.88 TMX $5.18 9/ /16 5 TMX $3.22 TMX $ / /16 5 TMX $3.55 TMX $6.39 5/ /16 5 TMX $3.72 TMX $ / /16 5 TMX $4.00 TMX $ / /16 5 TMX $4.12 TMX $ / /2 1 TMX $4.25 TMX $7.65 3/ /8 1 TMX $4.60 TMX $ / /4 1 TMX $4.85 TMX $ / /8 1 TMX $4.98 TMX $ / /16 1 TMX $5.13 TMX $9.23 7/ /16 1 TMX $5.28 TMX $ / /16 1 TMX $5.70 TMX $ / /16 1 TMX $6.15 TMX $ / /8 1 TMX $6.60 TMX $ / /2 1 TMX $6.80 TMX $12.24 C CARIDE INSERTS DEURRING

176 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SILVER & DEMING/REDUCED SHANK DRILLS 1/2 REDUCED SHANK DRILLS High Speed Steel,118 Self-Centering Split Point 1/2 reduced shank 118 point Round shank or 3-flat shank for positive hold 6, 3 flute length. Round 3 Flat Round 3 Flat PTD MORSE Master Catalog. PTD MORSE 33/64 PTD $20.45 MCT $ /64 PTD $32.04 MCT $ /32 PTD $19.94 MCT $ /32 PTD $31.10 MCT $ /64 PTD $21.78 MCT $ /64 PTD $37.49 MCT $ /16 PTD $21.17 MCT $ /16 PTD $32.72 MCT $ /64 PTD $23.36 MCT $ /64 PTD $38.84 MCT $ /32 PTD $22.77 MCT $ /32 PTD $33.84 MCT $ /64 PTD $24.53 MCT $ /64 PTD $40.32 MCT $ /8 PTD $23.85 MCT $ /8 PTD $35.15 MCT $ /64 PTD $26.19 MCT $ /64 PTD $42.12 MCT $ /32 PTD $25.43 MCT $ /32 PTD $36.68 MCT $ /64 PTD $27.23 MCT $ /64 PTD $45.00 MCT $ /16 PTD $26.42 MCT $ /16 PTD $39.20 MCT $ /64 PTD $27.59 MCT $ /64 PTD $47.70 MCT $ /32 PTD $26.78 MCT $ /32 PTD $41.45 MCT $ /64 PTD $29.97 MCT $ /64 PTD $52.65 MCT $ /4 PTD $29.21 MCT $ PTD $45.90 MCT $41.97 REDUCED SHANK SILVER & DEMING DRILLS 1/2 -HSS & Cobalt-118 Point 1/2 reduced shank 118 point 6, 3 flute length HSS or cobalt Full Line Available! Please call for more information. HSS Cobalt HSS Cobalt NEW ITEM! NEW ITEM! 33/64 I $ /64 I $ /32 I $15.18 I $ /32 I $ /64 I $17.01 I $ /64 I $ /16 I $17.01 I $ /16 I $31.17 I $ /64 I $17.01 I $ /64 I $ /32 I $17.01 I $ /32 I $ /64 I $17.01 I $ /64 I $ /8 I $17.01 I $ /8 I $35.55 I $ /64 I $18.23 I $ /64 I $ /32 I $18.23 I $ /32 I $ /64 I $18.23 I $ /64 I $ /16 I $18.23 I $ /16 I $44.20 I $ /64 I $18.98 I $ /64 I $ /32 I $20.78 I $ /32 I $ /64 I $20.78 I $ /64 I $ /4 I $20.88 I $ /4 I $44.71 I $ /64 I $21.39 I $ /64 I $ /32 I $22.66 I $ /32 I $ /64 I $23.63 I $ /64 I $ /16 I $23.63 I $ /16 I $49.50 I $ /64 I $23.68 I $ /64 I $ /32 I $23.68 I $ /32 I $ /64 I $23.68 I $ /64 I $ /8 I $25.06 I $ /8 I $54.80 I $ /64 I $25.61 I $ /64 I $ /32 I $26.38 I $ /32 I $ /64 I $27.16 I $ /64 I $ /16 I $27.65 I $ /16 I $59.68 I $ /64 I $29.84 I $ /64 I $ /32 I $29.94 I $ /32 I $ /64 I $30.05 I $ /64 I $ I $30.05 I $ /2 I $67.42 I $ C

177 REDUCED SHANK DRILLS/TAPER LENGTH DRILLS REDUCED SHANK SILVER & DEMING DRILLS 3/4 -High Speed Steel-118 Point 3/4 reduced shank 118 point 6, 3 flute length HSS TAPER LENGTH DRILLS High Speed Steel-right Finish 118 Conventional Point-High Helix NEW ITEM! 25/32 I $ /32 I $ /32 I $ /16 I $ /4 I $ /16 I $ /32 I $ /32 I $ /32 I $ /8 I $ /16 I $ /4 I $ /32 I $ /32 I $ /32 I $ /16 I $ /8 I $ /16 I $ /32 I $ /32 I $ /32 I $ I $ /16 I $ /8 I $ /32 I $ /32 I $ /32 I $ /16 I $ /2 I $ /16 I $ /32 I $ /32 I $ /32 I $ /8 I $ /16 I $ I $ /32 I $ /32 I $ /16 I $ /8 I $88.54 C Flute Length Flute Length Flute Length Master Catalog 445 1/64 5/16 1-1/2 PTD $ /64 4-1/4 6-3/4 PTD $ /64 5-5/8 9-1/2 PTD $ /32 3/4 2 PTD $4.88 3/8 4-1/4 6-3/4 PTD $ /32 5-5/8 9-1/2 PTD $ /64 1-1/8 2-1/4 PTD $ /64 4-3/8 7 PTD $ /64 5-7/8 9-3/4 PTD $ /16 1-3/4 3 PTD $ /32 4-3/8 7 PTD $ /4 5-7/8 9-3/4 PTD $ / /4 PTD $ /64 4-5/8 7-1/4 PTD $ / /8 PTD $ /32 2-1/4 4-1/4 PTD $3.31 7/16 4-5/8 7-1/4 PTD $ / /8 PTD $ /64 2-1/2 4-5/8 PTD $ /64 4-3/4 7-1/2 PTD $ /64 6-1/8 10 PTD $ /8 2-3/4 5-1/8 PTD $ /32 4-3/4 7-1/2 PTD $ /16 6-1/8 10 PTD $ / /8 PTD $ /64 4-3/4 7-3/4 PTD $ /64 6-1/8 10 PTD $ / /8 PTD $5.24 1/2 4-3/4 7-3/4 PTD $ /32 6-1/8 10 PTD $ /64 3-3/8 5-3/4 PTD $ /64 4-3/4 8 PTD $ /64 6-1/8 10 PTD $ /16 3-3/8 5-3/4 PTD $ /32 4-3/4 8 PTD $ /8 6-1/8 10 PTD $ /64 3-5/8 6 PTD $ /64 4-7/8 8-1/4 PTD $ /64 6-1/8 10 PTD $ /32 3-5/8 6 PTD $6.08 9/16 4-7/8 8-1/4 PTD $ /32 6-1/8 10 PTD $ /64 3-3/4 6-1/8 PTD $ /64 4-7/8 8-3/4 PTD $ /64 6-1/8 10-3/4 PTD $ /4 3-3/4 6-1/8 PTD $ /32 4-7/8 8-3/4 PTD $ /16 6-1/8 10-3/4 PTD $ /64 3-7/8 6-1/4 PTD $ /64 4-7/8 8-3/4 PTD $ /64 6-3/8 11 PTD $ /32 3-7/8 6-1/4 PTD $7.47 5/8 4-7/8 8-3/4 PTD $ /32 6-3/8 11 PTD $ / /8 PTD $ /64 5-1/8 9 PTD $ /64 6-3/8 11 PTD $ / /8 PTD $ /32 5-1/8 9 PTD $ /8 11 PTD $ /64 4-1/8 6-1/2 PTD $ /64 5-3/8 9-1/4 PTD $ /32 4-1/8 6-1/2 PTD $ /16 5-3/8 9-1/4 PTD $35.73 SPADE DRILLS-SOLID CARIDE For use on thin sheet applications and spot drilling Massive web construction insures maximum tool life Made from premium submicron carbide with 10% cobalt 118 drill point Made in Size Dec. Inch LOC Size Dec. Inch LOC 1/ /16 1-1/2 MO-SPD-132 $5.47 7/ /32 2 MO-SPD-732 $8.69 3/ /32 1-1/2 MO-SPD-364 $5.47 1/ /16 2 MO-SPD-14 $9.81 1/ /16 1-1/2 MO-SPD-116 $5.33 9/ /8 2-1/2 MO-SPD-932 $ / /16 1-1/2 MO-SPD-332 $5.21 5/ /8 2-1/2 MO-SPD-516 $ / /16 1-1/2 MO-SPD-764 $ / /16 2-1/2 MO-SPD-1132 $ / /2 1-1/2 MO-SPD-18 $5.27 3/ /8 2-1/2 MO-SPD-38 $ / /2 2 MO-SPD-964 $ / /8 2-1/2 MO-SPD-1332 $ / /16 2 MO-SPD-532 $6.45 7/ /16 2-1/2 MO-SPD-716 $ / /16 2 MO-SPD-1164 $ / /16 2-1/2 MO-SPD-1532 $ / /16 2 MO-SPD-316 $7.50 1/ /16 2-1/2 MO-SPD-12 $25.20 CARIDE INSERTS DEURRING

178 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID CARIDE DRILLS-STRAIGHT FLUTE STRAIGHT FLUTE DRILLS SOLID CARIDE FEATURES: For use on work hardened and abrasive materials such as stainless steel and heat treated steel alloys Precision tight tolerance holes Made from premium submicron carbide with 10% cobalt 140 notched drill point Made in Size Dec. LOC Size Dec. LOC Master Catalog Full Line Available! Please call for more information. 1/ /2 1-1/2 SFRUC-1/32-MO $ /16 2-1/4 SFRUC-10-MO $ /2 1-1/2 SFRUC-56-MO $ /16 2-1/4 SFRUC-9-MO $ / /2 1-1/2 SFRUC-3/64-MO $ /16 2-1/4 SFRUC-8-MO $ /2 1-1/2 SFRUC-55-MO $ /16 2-1/4 SFRUC-7-MO $ /2 1-1/2 SFRUC-54-MO $ / /16 2-1/4 SFRUC-13/64-MO $ /2 1-1/2 SFRUC-53-MO $ /4 2-3/8 SFRUC-6-MO $ / /8 1-5/8 SFRUC-1/16-MO $ /4 2-3/8 SFRUC-5-MO $ / /16 SFRUC-52-MO $ /4 2-3/8 SFRUC-4-MO $ / /16 SFRUC-51-MO $ /4 2-3/8 SFRUC-3-MO $ / /16 SFRUC-50-MO $8.04 7/ /4 2-3/8 SFRUC-7/32-MO $ / /16 SFRUC-49-MO $ /16 2-7/16 SFRUC-2-MO $ / /16 SFRUC-48-MO $ /16 2-7/16 SFRUC-1-MO $ / / /16 SFRUC-5/64-MO $7.26 A /16 2-7/16 SFRUC-A-MO $ /4 1-3/4 SFRUC-47-MO $ / /16 2-7/16 SFRUC-15/64-MO $ /4 1-3/4 SFRUC-46-MO $ /8 2-1/2 SFRUC--MO $ /4 1-3/4 SFRUC-45-MO $8.39 C /8 2-1/2 SFRUC-C-MO $ /4 1-3/4 SFRUC-44-MO $8.39 D /8 2-1/2 SFRUC-D-MO $ /4 1-3/4 SFRUC-43-MO $8.39 1/ /8 2-1/2 SFRUC-1/4-MO $ /4 1-3/4 SFRUC-42-MO $8.39 E /8 2-1/2 SFRUC-E-MO $ / /4 1-3/4 SFRUC-3/32-MO $7.61 F /16 2-5/8 SFRUC-F-MO $ / /16 SFRUC-41-MO $8.72 G /16 2-5/8 SFRUC-G-MO $ / /16 SFRUC-40-MO $ / /16 2-5/8 SFRUC-17/64-MO $ / /16 SFRUC-39-MO $8.72 H /2 2-11/16 SFRUC-H-MO $ / /16 SFRUC-38-MO $8.72 I /2 2-11/16 SFRUC-I-MO $ / /16 SFRUC-37-MO $ MM /2 2-11/16 SFRUC-7.0MM-MO $ / /16 SFRUC-36-MO $8.72 J /2 2-11/16 SFRUC-J-MO $ / / /16 SFRUC-7/64-MO $7.93 K /2 2-11/16 SFRUC-K-MO $ /8 1-7/8 SFRUC-35-MO $8.27 9/ /2 2-11/16 SFRUC-9/32-MO $ /8 1-7/8 SFRUC-34-MO $8.27 L /16 2-3/4 SFRUC-L-MO $ /8 1-7/8 SFRUC-33-MO $8.27 M /16 2-3/4 SFRUC-M-MO $ /8 1-7/8 SFRUC-32-MO $ / /16 2-3/4 SFRUC-19/64-MO $ /8 1-7/8 SFRUC-31-MO $8.27 N /8 2-13/16 SFRUC-N-MO $ / /8 1-7/8 SFRUC-1/8-MO $8.03 5/ /8 2-13/16 SFRUC-5/16-MO $ / /16 SFRUC-30-MO $8.53 O / /16 SFRUC-O-MO $ / /16 SFRUC-29-MO $9.00 P / /16 SFRUC-P-MO $ / /16 SFRUC-28-MO $ / / /16 SFRUC-21/64-MO $ / / /16 SFRUC-9/64-MO $9.05 Q /16 3 SFRUC-Q-MO $ /16 SFRUC-27-MO $9.68 R /16 3 SFRUC-R-MO $ /16 SFRUC-26-MO $ / /16 3 SFRUC-11/32-MO $ /16 SFRUC-25-MO $9.68 S /4 3-1/16 SFRUC-S-MO $ /16 SFRUC-24-MO $9.68 T /4 3-1/16 SFRUC-T-MO $ /16 SFRUC-23-MO $ / /4 3-1/16 SFRUC-23/64-MO $ / /16 SFRUC-5/32-MO $10.03 U /16 3-1/8 SFRUC-U-MO $ /16 2-1/8 SFRUC-22-MO $ / /16 3-1/8 SFRUC-3/8-MO $ /16 2-1/8 SFRUC-21-MO $10.21 V /8 3-1/4 SFRUC-V-MO $ /16 2-1/8 SFRUC-20-MO $10.21 W /8 3-1/4 SFRUC-W-MO $ /16 2-1/8 SFRUC-19-MO $ / /8 3-1/4 SFRUC-25/64-MO $ /16 2-1/8 SFRUC-18-MO $12.57 X /16 3-5/16 SFRUC-X-MO $ / /16 2-1/8 SFRUC-11/64-MO $10.56 Y /16 3-5/16 SFRUC-Y-MO $ /8 2-3/16 SFRUC-17-MO $ / /16 3-5/16 SFRUC-13/32-MO $ /8 2-3/16 SFRUC-16-MO $13.28 Z /8 SFRUC-Z-MO $ /8 2-3/16 SFRUC-15-MO $ / /8 SFRUC-27/64-MO $ /8 2-3/16 SFRUC-14-MO $ / /16 3-7/16 SFRUC-7/16-MO $ /8 2-3/16 SFRUC-13-MO $ / /8 3-9/16 SFRUC-29/64-MO $ / /8 2-3/16 SFRUC-3/16-MO $ / /8 3-5/8 SFRUC-15/32-MO $ /16 2-1/4 SFRUC-12-MO $ / / /16 SFRUC-31/64-MO $ /16 2-1/4 SFRUC-11-MO $ / /4 3-3/4 SFRUC-1/2-MO $67.12 C

179 COMINED DRILL & COUNTERSINKS COMINED DRILL & COUNTERSINKS PLAIN TYPE-60, 82 and 90 Included Angle Used for producing center holes in components or workpieces which requre machining between centers Available in 60, 82 and 90 included angles Right hand -left hand also available Available with TiN coating Made in the Size ody Point Point Length HSS 60 Included Angle 82 Included Angle 90 Included Angle COALT HSS HSS / /4 KEO $7.45 KEO $29.29 KEO $24.38 KEO $ / /4 KEO $6.84 KEO $28.47 KEO $24.38 KEO $ / /4 KEO $6.47 KEO $19.34 KEO $15.62 KEO $ / /4 KEO $6.47 KEO $19.34 KEO $16.48 KEO $ /8 1/32 1/32 1-1/4 KEO $6.47 KEO $19.34 KEO $16.48 KEO $16.48 #1 1/8 3/64 3/64 1-1/4 KEO $4.51 KEO $10.48 KEO $7.39 KEO $7.39 #2 3/16 5/64 5/64 1-7/8 KEO $4.72 KEO $10.82 KEO $7.57 KEO $7.57 #3 1/4 7/64 7/64 2 KEO $4.92 KEO $11.18 KEO $7.82 KEO $7.82 #4 5/16 1/8 1/8 2-1/8 KEO $5.07 KEO $11.63 KEO $8.13 KEO $8.13 #4-1/2 3/8 9/64 9/64 2-1/2 KEO $6.98 KEO $17.29 KEO $11.14 KEO $11.14 #5 7/16 3/16 3/16 2-3/4 KEO $8.03 KEO $18.34 KEO $12.40 KEO $12.40 #6 1/2 7/32 7/32 3 KEO $12.09 KEO $28.45 KEO $18.76 KEO $18.76 #7 5/8 1/4 1/4 3-1/4 KEO $18.34 KEO $42.80 KEO $26.56 KEO $26.56 #8 3/4 5/16 5/16 3-1/2 KEO $25.19 KEO $60.60 KEO $37.23 KEO $37.23 #9 7/8 11/32 11/32 3-5/8 KEO $45.71 KEO $ KEO $68.68 KEO $68.68 #10 1 3/8 3/8 3-3/4 KEO $59.99 KEO $ KEO $90.36 KEO $ PIECE COMINED DRILL & COUNTERSINK SETS 60 Included Angle Right Hand HSS 5 piece set includes #1 through #5 plain type combined drill and countersink with 60 included angle Available in HSS, cobalt and carbide Provided with wooden case Made in the NEW ITEM! COMINED DRILL & COUNTERSINKS Plain Type 60 Angle HSS & M42 Cobalt NEW ITEM! Size ody Point Point Lngth Description Set #1 - #5 HSS KEO $40.91 #1 - #5 TiN Coated KEO TIN $52.36 #1 - #5 Cobalt KEO $76.08 #1 - #5 Carbide KEO $ HSS M2 COALT 000 1/ /4 MAG $ / /4 MAG $ / /4 MAG $ / /4 MAG $ /8 3/64 3/64 1-1/4 MAG $4.89 MAG $9.77 (S 2) 3/16 1/16 1/16 1-3/4 MAG $ /16 5/64 5/64 1-7/8 MAG $5.06 MAG $ /4 7/64 7/64 2 MAG $5.29 MAG $ /16 1/8 1/8 2-1/8 MAG $5.50 MAG $ /2 3/8 9/64 9/64 2-1/2 MAG $ /16 3/16 3/16 2-3/4 MAG $8.68 MAG $ /2 7/32 7/32 3 MAG $12.90 MAG $ /8 1/4 1/4 3-1/4 MAG $18.89 MAG $ /4 5/16 5/16 3-1/2 MAG $29.34 MAG $58.71 C CARIDE INSERTS COMINED DRILL & COUNTERSINKS Plain Type- 82 /90 Angle M2 HSS Size ody Point Point 82 Angle 90 Angle Lngth 1 1/8 3/64 3/64 1-1/4 MAG MAG $ /16 5/64 5/64 1-7/8 MAG MAG $ /4 7/64 7/64 2 MAG MAG $ /16 1/8 1/8 2-1/8 MAG MAG $ /16 3/16 3/16 2-3/4 MAG MAG $ /2 7/32 7/32 3 MAG MAG $ /8 1/4 1/4 3-1/4 MAG MAG $ /4 5/16 5/16 3-1/2 MAG MAG $ Master Catalog 447 C DEURRING

180 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID SPADE DRILLS/COUNTERSINKS PLAIN TYPE COMINED DRILL & COUNTERSINKS Solid Carbide Manufactured from premium sub-micron carbide with 10 cobalt Pilot has 118 drill point Available with 60, 82 or 90 included angle TiN Coated 60 also available Made in Full Line Available! Please call for more information. COMINED DRILL & COUNTERSINKS SOLID CARIDE-PLAIN TYPE-60 Included Angle Used for producing center holes in components or workpieces which requre machining between centers Available with 60 included angle Right hand Made in the meter Size Point ELL TYPE COMINED DRILL & COUNTERSINKS 60 Included Angle-HSS & Cobalt NEW ITEM! Used for producing center holes in components or workpieces which require machining between centers Additional 120 included chamfer eliminates the risk of deforming the countersink seat Right hand and left hand available Made in the Full Line Available! Please call for more information. Size ody Master Catalog 60 Angle 82 Angle 90 Angle /8 1-1/2 MO-CD00-60 MO-CD00-82 MO-CD00-90 $ /32 1/8 1-1/2 MO-CD0-60 MO-CD0-82 MO-CD0-90 $ /64 1/8 1-1/2 MO-CD1-60 MO-CD1-82 MO-CD1-90 $ /64 3/16 1-7/8 MO-CD2-60 MO-CD2-82 MO-CD2-90 $ /64 1/4 2 MO-CD3-60 MO-CD3-82 MO-CD3-90 $ /8 5/16 2-1/8 MO-CD4-60 MO-CD4-82 MO-CD4-90 $ /16 7/16 2-3/4 MO-CD5-60 MO-CD5-82 MO-CD5-90 $ /32 1/2 3 MO-CD6-60 MO-CD6-82 MO-CD6-90 $ /4 5/8 3-1/4 MO-CD7-60 MO-CD7-82 MO-CD7-90 $ /16 3/4 3-1/2 MO-CD8-60 MO-CD8-82 MO-CD8-90 $ Point. COMINED DRILL & COUNTERSINKS ell Type- 60 /120 Angles-HSS Magafor combined drills and countersinks with a 120 chamfer protects the 60 countersink from any risk of blows and deformation. The splay resulting from the protective chamfer makes it easier to load parts between centers on machines with automatic feed. Point Length NEW ITEM! ell. Size ody. Point Point Length 00 1/ /2 KEO $13.29 #0 1/8 1/32 1/32 1-1/2 KEO $12.09 #1 1/8 3/64 3/64 1-1/2 KEO $12.09 #2 3/16 5/64 5/64 2 KEO $18.21 #3 1/4 7/64 7/64 2 KEO $22.74 #4 5/16 1/8 1/8 2-1/8 KEO $27.02 #5 7/16 3/16 3/16 2-3/4 KEO $42.10 #6 1/2 7/32 7/32 3 KEO $51.21 #7 5/8 1/4 1/4 3-3/4 KEO $ #8 3/4 5/16 5/16 4 KEO $ HSS R H COALT R H HSS L H #11 1/8 3/64 3/64 1-1/ KEO $5.39 KEO $12.80 KEO $12.54 #12 3/16 1/16 1/16 1-7/ KEO $5.65 KEO $13.12 KEO $12.94 #13 1/4 3/32 3/ KEO $5.73 KEO $13.47 KEO $13.31 #14 5/16 7/64 7/64 2-1/ KEO $5.92 KEO $13.92 KEO $13.83 #15 7/16 5/32 5/32 2-3/ KEO $9.00 KEO $22.20 KEO $19.32 #16 1/2 3/16 3/ KEO $13.87 KEO $34.32 KEO $28.15 #17 5/8 7/32 7/32 3-1/ KEO $21.48 KEO $51.08 KEO $39.68 #18 3/4 1/4 1/4 3-1/ KEO $28.47 KEO $71.28 KEO $52.24 #19 7/8 5/16 5/16 3-5/ KEO $49.12 KEO $ KEO $92.33 #20 1 3/8 3/8 3-3/ KEO $63.30 KEO $ KEO $ Size ody ell Point Point Length 11 1/ /64 3/64 1-1/4 MAG $ / /16 1/16 1-7/8 MAG $ / /32 3/32 2 MAG $ / /64 7/64 2-1/8 MAG $ / /32 5/32 2-3/4 MAG $ / /16 3/16 3 MAG $ / /32 7/32 3-1/4 MAG $ / /4 1/4 3-1/2 MAG $ / /16 5/16 3-5/8 MAG $ /8 3/8 3-3/4 MAG $68.57 C C

181 COMINED DRILL & COUNTERSINKS RADIUS TYPE COMINED DRILL & COUNTERSINKS High Speed Steel Size Available in American standard sizes Designed to reduce bearing surface of the center hole and provide a protected centering seat, virtually eliminating the risk of breakage Made in the NEW ITEM! COMINED DRILL & COUNTERSINKS RADIUS TYPE M2 HSS The Special Profile on this tool is more robust than the 60 angle on a regular combined drill & countersink. The radius serves as a protective chamfer, helping to eliminate the risk of breakage and making it easier to locate the center hole on automatic feeding machines. The radius on this tool works well for 60, 82, or 90 angle. LONG COMINED DRILL & COUNTERSINKS PLAIN TYPE-60, 82 and 90 Included Angle Size ody ody. Radius Point. Point Point Length Profile Length Radius HSS #5-0 1/ /4 1/16 KEO $8.70 #4-0 1/ /4 5/64 KEO $8.25 #3-0 1/ /4 3/32 KEO $7.14 #2-0 1/ /4 7/64 KEO $7.14 #0 1/8 1/ /4 1/8 KEO $7.14 #1 1/8 3/ /4 5/32 KEO $5.58 #2 3/16 5/ /8 7/32 KEO $5.92 #3 1/4 7/ /32 KEO $6.40 #4 5/16 1/8 11/32 2-1/8 3/8 KEO $7.19 #4-1/2 3/8 9/64 13/32 2-1/2 7/16 KEO $8.81 #5 7/16 3/16 31/64 2-3/4 1/2 KEO $10.01 #6 1/2 7/32 35/64 3 9/16 KEO $15.13 #7 5/8 1/4 43/64 3-1/4 45/64 KEO $22.19 #8 3/4 5/16 13/16 3-1/2 7/8 KEO $29.98 #9 7/8 11/32 15/16 3-5/8 1 KEO $56.05 #10 1 3/8 1-1/16 3-3/4 1-7/64 KEO $ /8 5/32 3/ /4 MAG $ /16 7/32 5/ /8 MAG $ /4 9/32 7/ MAG $ /16 3/8 1/8 11/32 2-1/8 MAG $ /16 1/2 3/16 31/64 2-3/4 MAG $ /2 9/16 7/32 35/64 3 MAG $ /8 45/64 1/4 43/64 3-1/4 MAG $ /4 7/8 5/16 13/16 3-1/2 MAG $36.70 NEW ITEM! C Used for producing center holes in components or workpieces which requre machining between centers Available in 60, 82 and 90 included angles Long series Made in the Size ody Point Point Length HSS 60 Angle 82 Angle 90 Angle COALT HSS HSS #1 3 1/8 3/64 3/64 KEO $10.92 KEO $32.77 KEO $16.88 KEO $16.88 #1 4 1/8 3/64 3/64 KEO $11.39 KEO $33.88 KEO $19.17 KEO $19.17 #1 5 1/8 3/64 3/64 KEO $15.83 KEO $47.15 KEO $26.64 KEO $26.64 #1 6 1/8 3/64 3/64 KEO $20.73 KEO $61.61 KEO $34.86 KEO $34.86 #2 3 3/16 5/64 5/64 KEO $11.05 KEO $32.86 KEO $18.53 KEO $18.53 #2 4 3/16 5/64 5/64 KEO $12.49 KEO $37.15 KEO $20.97 KEO $20.97 #2 5 3/16 5/64 5/64 KEO $16.00 KEO $47.61 KEO $26.64 KEO $26.64 #2 6 3/16 5/64 5/64 KEO $20.81 KEO $61.99 KEO $35.02 KEO $35.02 #3 3 1/4 7/64 7/64 KEO $11.53 KEO $34.26 KEO $19.39 KEO $19.39 #3 4 1/4 7/64 7/64 KEO $13.15 KEO $39.05 KEO $22.11 KEO $22.11 #3 5 1/4 7/64 7/64 KEO $17.30 KEO $51.52 KEO $29.12 KEO $29.12 #3 6 1/4 7/64 7/64 KEO $21.00 KEO $62.48 KEO $35.26 KEO $35.26 #4 3 5/16 1/8 1/8 KEO $13.54 KEO $40.25 KEO $22.73 KEO $22.73 #4 4 5/16 1/8 1/8 KEO $14.58 KEO $43.38 KEO $24.53 KEO $24.53 #4 5 5/16 1/8 1/8 KEO $18.63 KEO $55.43 KEO $31.32 KEO $31.32 #4 6 5/16 1/8 1/8 KEO $21.52 KEO $63.99 KEO $36.20 KEO $36.20 #4-1/2 4 3/8 9/64 9/64 KEO $16.39 KEO $47.66 KEO $26.97 KEO $26.97 #4-1/2 5 3/8 9/64 9/64 KEO $19.37 KEO $56.51 KEO $31.99 KEO $31.99 #4-1/2 6 3/8 9/64 9/64 KEO $23.36 KEO $68.21 KEO $38.58 KEO $38.58 #5 4 7/16 3/16 3/16 KEO $19.15 KEO $55.90 KEO $31.59 KEO $31.59 #5 5 7/16 3/16 3/16 KEO $22.18 KEO $64.71 KEO $36.62 KEO $36.62 #5 6 7/16 3/16 3/16 KEO $24.90 KEO $72.62 KEO $41.08 KEO $41.08 #6 4 1/2 7/32 7/32 KEO $20.78 KEO $59.36 KEO $25.83 KEO $25.83 #6 5 1/2 7/32 7/32 KEO $23.83 KEO $68.28 KEO $38.58 KEO $38.58 #6 6 1/2 7/32 7/32 KEO $28.80 KEO $82.36 KEO $46.55 KEO $46.55 #7 6 5/8 1/4 1/4 KEO $53.67 KEO $ KEO $86.46 KEO $86.46 #8 6 3/4 5/16 5/16 KEO $57.95 KEO $ KEO $93.45 KEO $ Master Catalog 449 CARIDE INSERTS DEURRING

182 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD COUNTERSINKS/SPOTTING DRILLS PLAIN TYPE- 60 ANGLE HSS M2- Long Style Size #1 #2 #3 #4 ody Point Point Length 3 1/8 3/64 3/64 MAG $ /8 3/64 3/64 MAG $ /8 3/64 3/64 MAG $ " 1/8 3/64 3/64 MAG $ " 3/16 5/64 5/64 MAG $9.89 4" 3/16 5/64 5/64 MAG $ " 3/16 5/64 5/64 MAG $ " 3/16 5/64 5/64 MAG $ " 1/4 7/64 7/64 MAG $ " 1/4 7/64 7/64 MAG $ " 1/4 7/64 7/64 MAG $ " 1/4 7/64 7/64 MAG $ " 5/16 1/8 1/8 MAG $ " 5/16 1/8 1/8 MAG $13.07 N/C SPOTTING DRILLS 82, 90 & 120 Point Angles High speed steel or cobalt Designed with a narrow chisel edge for quick starting Constant web allows for resharpening without the need for web thinning Right hand ody Flute Length 82 Point Angle 90 Point Angle 120 Point Angle COALT HSS COALT Master Catalog Size ody Point Point Length #4 5" 5/16 1/8 1/8 MAG $ " 5/16 1/8 1/8 MAG $ " 3/8 9/64 9/64 MAG $14.64 #4-1/2 5" 3/8 9/64 9/64 MAG $ " 3/8 9/64 9/64 MAG $ " 7/16 3/16 3/16 MAG $17.06 #5 5" 7/16 3/16 3/16 MAG $ " 7/16 3/16 3/16 MAG $ " 1/2 7/32 7/32 MAG $18.51 #6 5" 1/2 7/32 7/32 MAG $ " 1/2 7/32 7/32 MAG $26.39 #7 5" 5/8 1/4 1/4 MAG $ " 5/8 1/4 1/4 MAG $47.62 #8 6" 3/4 5/16 5/16 MAG $52.68 HSS COALT 1/4 3/4 2-1/2 KEO $24.34 KEO $21.51 KEO $24.34 KEO $21.51 KEO $ /4 3/4 4 KEO $35.03 KEO $30.95 KEO $35.03 KEO $30.95 KEO $ /4 3/4 6 KEO $48.10 KEO $42.50 KEO $48.10 KEO $42.50 KEO $ /8 1-1/8 3-1/8 KEO $26.28 KEO $23.22 KEO $26.28 KEO $23.22 KEO $ /8 1-1/8 5 KEO $37.34 KEO $32.99 KEO $37.34 KEO $32.99 KEO $ /8 1-1/8 7 KEO $51.73 KEO $45.72 KEO $51.73 KEO $45.72 KEO $ /2 1-3/8 3-3/4 KEO $33.69 KEO $29.76 KEO $33.69 KEO $29.76 KEO $ /2 1-3/8 6 KEO $46.70 KEO $41.26 KEO $46.70 KEO $41.26 KEO $ /2 1-3/8 8 KEO $63.51 KEO $56.12 KEO $63.51 KEO $56.12 KEO $ /8 1-5/8 4-3/8 KEO $43.84 KEO $38.74 KEO $43.84 KEO $38.74 KEO $ /8 1-5/8 7 KEO $59.02 KEO $52.15 KEO $59.02 KEO $52.15 KEO $ /8 1-5/8 9 KEO $81.59 KEO $72.09 KEO $81.59 KEO $72.09 KEO $ /4 1-7/8 5 KEO $59.97 KEO $52.99 KEO $59.97 KEO $52.99 KEO $ /4 1-7/8 8 KEO $81.07 KEO $71.64 KEO $81.07 KEO $71.64 KEO $ /4 1-7/8 10 KEO $ KEO $95.75 KEO $ KEO $95.75 KEO $ /4 6 KEO $ KEO $91.16 KEO $ KEO $91.16 KEO $ /4 8 KEO $ KEO $97.04 KEO $ KEO $97.04 KEO $ /4 10 KEO $ KEO $ KEO $ KEO $ KEO $ SPOTTING & CENTERING DRILLS 90 & 118 Point Angles Prevents misalignment caused by using regular drills for centering These short drills can be chucked close to the point, ensuring accuracy and true starts Made in the NEW ITEM! ody. Flute Length NEW ITEM! HSS 90 Point 118 Point TIN Coated HSS TIN Coated 1/8 3/8 1-1/4 KEO $4.42 KEO TIN $5.27 KEO $4.42 KEO TIN $5.27 3/16 1/2 1-3/8 KEO $4.80 KEO TIN $6.03 KEO $4.80 KEO TIN $6.03 1/4 5/8 1-1/2 KEO $5.30 KEO TIN $6.93 KEO $5.30 KEO TIN $6.93 5/16 5/8 1-1/2 KEO $6.03 KEO TIN $8.09 KEO $6.03 KEO TIN $8.09 3/8 1 2 KEO $6.82 KEO TIN $8.89 KEO $6.82 KEO TIN $8.89 7/ KEO $9.19 KEO TIN $12.52 KEO $9.19 KEO TIN $ /2 1 2 KEO $11.25 KEO TIN $14.59 KEO $11.25 KEO TIN $ / KEO $16.75 KEO TIN $20.90 KEO $16.75 KEO TIN $ /8 1-1/8 2-1/4 KEO $18.62 KEO TIN $24.13 KEO $18.62 KEO TIN $ /4 1-1/8 2-1/4 KEO $25.87 KEO TIN $32.20 KEO $25.87 KEO TIN $ /8 1-1/4 2-1/2 KEO $31.72 KEO TIN $40.39 KEO $31.72 KEO TIN $ /4 2-1/2 KEO $40.54 KEO TIN $51.55 KEO $40.54 KEO TIN $ /4 2 4 KEO $79.40 KEO TIN $95.94 KEO $79.40 KEO TIN $ /2 2-1/2 5 KEO $ KEO TIN $ KEO $ KEO TIN $ /4 2-3/4 5-1/2 KEO $ KEO TIN $ KEO $ KEO TIN $ C

183 CENTER/SPOTTING DRILLS NC SPOTTING DRILLS HSS M35 5% Cobalt-Standard Length Very narrow chisel edge. Short flute and stubby length provide precise spotting prior to drilling. H6 tolerance ensures perfect centering of the web and cutting edge. Point Angle 90 can combine centering and chamfering into one operation. Point Angle 120 best when follow-on drill has a 118 drill point, precise hole location. SOLID CARIDE N/C SPOTTING DRILLS 90 & 120 Point Angles Solid carbide Designed with a narrow chisel edge for quick starting Right hand Made in the NEW ITEM! Flute Length SPOTTING AND CENTERING DRILLS 82, 90, 100, 120 Included Drill Point CENTER DRILL HOLDER Uncoated 90 Point Angle 120 Point Angle TIN Coated Uncoated TIN Coated 1/8 3/8 1-1/2 KEO $13.70 KEO TIN $14.54 KEO $13.70 KEO TIN $ /16 9/16 2 KEO $18.02 KEO TIN $19.22 KEO $18.02 KEO TIN $ /4 3/4 2-1/2 KEO $22.99 KEO TIN $25.16 KEO $22.99 KEO TIN $ /16 3/4 2-1/2 KEO $27.73 KEO TIN $30.44 KEO $27.73 KEO TIN $ /8 3/4 2-1/2 KEO $31.17 KEO TIN $33.88 KEO $31.17 KEO TIN $ /2 1 3 KEO $48.74 KEO TIN $53.06 KEO $48.74 KEO TIN $ / /2 KEO $89.76 KEO TIN $96.56 KEO $89.76 KEO TIN $ /4 1-1/8 4 KEO $ KEO TIN $ KEO $ KEO TIN $ Flute Len. 1/4 2 3/4 5/16 2 3/4 3/ / Size Dec. Incl. Flute Incl.. Drill Pt. Len. Drill Pt. 82 MI-SPD MI-SPD MI-SPD MI-SPD $ / MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD $ /8 2-1/2 1-1/8 100 MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD $ /4 2-1/2 1-1/8 100 MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD MI-SPD $ /2 1-1/4 100 MI-SPD MI-SPD MI-SPD MI-SPD Save Valuable Time! It gets into spaces that others can't even begin to! ecause the holder is configured and located in the lathe turret like an OD turning tool, the only thing protruding in front of the turret face is the tip of the center drill. As a result, the center drill can be programmed to drop into the space between the end of the part to be center drilled and the tip of the live center in the retracted position, a space less than the travel on most tailstock quills. The time consuming process of stopping the machine to reposition the workpiece or the tailstock during the machining cycle is completely eliminated. Cutting Length 90 Angle 120 Angle 2 mm /8 5/16 MAG MAG $ mm /16 MAG MAG $ mm /16 1/2 MAG MAG $ mm /8 5/8 MAG MAG $ mm /8 3/4 MAG MAG $ / /8 7/8 MAG MAG $ mm /8 1 MAG MAG $ / /2 1 MAG MAG $ / /8 MAG MAG $ / /2 1-3/8 MAG MAG $ / /8 1-5/8 MAG MAG $ /2 1-3/4 MAG MAG $98.56 Max. Center meter The 3/4 and 1 kits come complete with 1/2 OD bushings to accommodate standard center drills from #1 to #6, ell type center drills for #11 to #16 and spotting centers up to 1/2 diameter. The 1 1/4 kit comes complete with (5) 3/4 OD bushings of your choice. $49.05 $86.75 $ $ /4" 1/2" ED-CDH $ " 1/ 2" ED-CDH1-500 $ /4" 3/4" ED-CDH $ Master Catalog 451 C C CARIDE INSERTS DEURRING

184 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD COUNTERSINKS ZErO FLUTE M35 COALT COUNTERSINK AND DEURRING TOOLS. of Cut All-purpose tool provides flawless counter sinking and deburring Chatter-free cutting action requires minimal power Micro-smooth CNC precision ground construction produces clean, smooth cutting without smearing on a variety of materials Works on all materials- excels in aluminum, plastics and other nonmetallic materials Made in the FEATURES: Zeroflute deburring tools give chatterless finishes. Single cutting edge for fast removal of stock. Free Cutting. Designed for and 90 cutting. Easily sharpened by use of a small mounted grinding wheel inserted into hole. Head. Min. Max. 60 Angle Master Catalog 5/16 7/64 9/32 1-7/8 1/4 KEO $ /8 5/32 11/32 1-7/8 1/4 KEO $ /2 11/64 29/64 2 5/16 KEO $ /8 3/16 37/64 2-1/2 3/8 KEO $ /4 1/4 45/64 2-3/4 3/8 KEO $ /64 27/32 3 3/8 KEO $ /4 27/64 1-1/32 3-1/2 1/2 KEO $84.41 Head..of Cut 82 Angle 90 Angle 100 Angle Min. Max. ZEROFLUTE COUNTERSINKS & DEURRING TOOLS HSS-M35 5% Cobalt SINGLE FLUTE COUNTERSINKS 60, 82 & 90 Point Angles-HSS & Cobalt Ideal for chamfering, deburring and countersinking Large positive rake and single flute construction provide a smooth surface finish on a wide variety of materials Tool versatility can help increse productivity on all general purpose applications Made in the ody Single flute countersinks provide smooth finishes on a wide range of materials. Great countersinking capacity from the point to the outside diameter. Complete size range is available in or 90 included angles. 4 PIECE ZERO FLUTE COUNTERSINK SETS 4 Piece Set Includes: 5/16, 3/8, 1/2, 5/8 C Sink Angle 60 KEO $ KEO $ KEO $ /16 3/32 9/32 1-5/8 1/4 KEO $11.71 KEO $11.71 KEO $ /8 9/64 11/32 1-3/4 1/4 KEO $13.38 KEO $13.38 KEO $ /2 5/32 29/64 1-3/4 5/16 KEO $16.03 KEO $16.03 KEO $ /8 11/64 37/64 2-1/8 3/8 KEO $18.39 KEO $18.39 KEO $ /4 13/64 45/64 2-3/8 3/8 KEO $28.01 KEO $28.01 KEO $ /64 59/64 2-5/8 3/8 KEO $34.84 KEO $34.84 KEO $ /4 23/64 1-3/32 3-1/8 1/2 KEO $84.41 KEO $84.41 KEO $84.41 Size ody of Cut 60 Angle 82 Angle 90 Angle Min* Max 0+ 1/ /4 1/4 MAG MAG MAG $ / /4 1/4 MAG MAG MAG $ / /4 MAG MAG MAG $ / /8 1/2 MAG MAG MAG $ / /2 1/2 MAG MAG MAG $55.38 *15% to 20% greater for 60 countersinks only + Double Ended 60 Angle SINGLE FLUTE COUNTERSINKS HSS-M35 5% Cobalt Size HIGH SPEED STEEL 82 Angle NEW ITEM! 90 Angle NEW ITEM! 60 Angle COALT 82 Angle 90 Angle 1/8 1-1/4 1/8 KEO KEO KEO $7.26 KEO KEO KEO $8.35 3/16 1-3/8 3/16 KEO KEO KEO $7.44 KEO KEO KEO $8.56 1/4 1-1/2 1/4 KEO KEO KEO $7.75 KEO KEO KEO $8.91 3/8 1-3/4 1/4 KEO KEO KEO $8.83 KEO KEO KEO $ /2 2 1/4 KEO KEO KEO $10.81 KEO KEO KEO $ /8 2-1/4 3/8 KEO KEO KEO $14.46 KEO KEO KEO $ /4 2-5/8 1/2 KEO KEO KEO $21.11 KEO KEO KEO $ /4 1/2 KEO KEO KEO $36.19 KEO KEO KEO $ /4 3 1/2 KEO KEO KEO $70.85 KEO KEO KEO $ /2 3-1/4 3/4 KEO KEO KEO $95.94 KEO KEO KEO $ /4 3-1/2 3/4 KEO KEO KEO $ KEO KEO KEO $ /4 3/4 KEO KEO KEO $ KEO KEO KEO $ Angle 82 Angle 90 Angle 1/8 1-1/4 1/8 MAG MAG MAG $9.21 3/16 1-3/8 3/16 MAG MAG MAG $9.68 1/4 1-1/2 1/4 MAG MAG MAG $9.84 5/16 1-5/8 1/4 MAG MAG MAG $ /8 1-3/4 1/4 MAG MAG MAG $ /2 2 1/4 MAG MAG MAG $ /8 2-1/4 3/8 MAG MAG MAG $ /4 2-5/8 1/2 MAG MAG MAG $ /8 2-3/4 1/2 MAG MAG MAG $ /4 1/2 MAG MAG MAG $ /4 2-3/4* 1/2 MAG MAG MAG $77.78 *The 60 Countersink (MAG ) has an overall length of 3 C C

185 COUNTERSINKS/CENTER REAMERS THREE FLUTE CENTER REAMERS 60, 82 & 90 Point Angles-High Speed Steel KEO 3-flute center reamers are versatile tools designed for countersinking holes for centers or for enlarging existing holes. Made from high speed steel. 3 & 6 FLUTE CENTER REAMER/COUNTERSINK SETS High Speed Steel & Cobalt (5) piece 3 flute sets include 1 each of 1/4, 3/8, 1/2, 3/4 and 1 body diameter with selected point angle (7) piece 6 flute HSS set includes* 1/4, 3/8, 1/2, 3/4 and 1 body diameter with selected point angle (5) piece 6 flute Cobalt sets includes 1/4, 3/8, 1/2, 3/4 and 1 body diameter with selected point angle Includes storage container HIGH SPEED STEEL COUNTERSINKS Single & 6 Flute Crafted from premium HSS material Easily resharpened 100 Angle countersinks and sets also available DENIM SHOP APRONS 100% blue cotton denim E version includes waist pocket PR version includes chest pocket w/ pen holder One size fits all 35 length x 28 wide Single Flute ody 60 Angle 82 Angle 90 Angle 120 Angle 1/8 1-1/2 1/8 MO-HC MO-HC MO-HC MO-HC $5.86 3/16 1-1/2 3/16 MO-HC MO-HC MO-HC MO-HC $5.99 1/4 2 1/4 MO-HC MO-HC MO-HC MO-HC $6.26 3/8 2 1/4 MO-HC MO-HC MO-HC MO-HC $7.10 1/2 2 1/4 MO-HC MO-HC MO-HC MO-HC $8.64 5/8 2-3/4 1/2 MO-HC MO-HC MO-HC MO-HC $ /4 2-3/4 1/2 MO-HC MO-HC MO-HC MO-HC $ /4 1/2 MO-HC MO-HC MO-HC MO-HC $ /4 3 3/4 MO-HC MO-HC MO-HC MO-HC $ /2 3-1/2 3/4 MO-HC MO-HC MO-HC MO-HC $ Flute ody Set Angle ody HSS 60 Angle 60 Angle 82 Angle 90 Angle 82 Angle 90 Angle 120 Angle 1/4 1-1/2 1/4 KEO $8.19 KEO KEO $8.19 3/8 1-3/4 1/4 KEO $9.21 KEO KEO $9.21 1/2 2 1/4 KEO $11.34 KEO KEO $ /8 2-1/4 3/8 KEO $15.09 KEO KEO $ /4 2-5/8 1/2 KEO $22.06 KEO KEO $ /4 1/2 KEO $35.10 KEO KEO $ /4 2-3/4* 1/2 KEO $85.33 KEO KEO $ /2 2-7/8* 3/4 KEO $ KEO KEO $ /4 3* 3/4 KEO $ KEO KEO $ /4* 3/4 KEO $ KEO KEO $ *60 :1-1/4=3", 1-1/2=3-1/4", 1-3/4=3-1/2", 2"=3-3/4" 3-FLUTE SETS Set COALT Set HSS 6 FLUTE SETS Set COALT Set 60 KEO $99.24 KEO $ KEO-55018* $ KEO $ KEO $99.24 KEO $ KEO-55038* $ KEO $ KEO $99.24 KEO $ KEO-55058* $ KEO $ KEO $99.24 KEO $ KEO-55078* $ KEO $ KEO $99.24 KEO $ KEO-55098* $ KEO $ KEO $99.24 KEO $ KEO-55118* $ KEO $ /8 1-1/2 1/8 MO-HC MO-HC MO-HC MO-HC $5.86 3/16 2 3/16 MO-HC MO-HC MO-HC MO-HC $5.99 1/4 2 1/4 MO-HC MO-HC MO-HC MO-HC $6.26 5/16 2 1/4 MO-HC MO-HC MO-HC MO-HC $7.36 3/8 2-1/2 1/4 MO-HC MO-HC MO-HC MO-HC $7.98 1/2 2-1/2 3/8 MO-HC MO-HC MO-HC MO-HC $9.39 5/8 2-1/2 1/2 MO-HC MO-HC MO-HC MO-HC $ /4 2-3/4 1/2 MO-HC MO-HC MO-HC MO-HC $ /8 2-3/4 1/2 MO-HC MO-HC MO-HC MO-HC $ /4 1/2 MO-HC MO-HC MO-HC MO-HC $ /4 3 3/4 MO-HC MO-HC MO-HC MO-HC $ /2 3-1/2 3/4 MO-HC MO-HC MO-HC MO-HC $62.51 NEW ITEM! NEW ITEM! NEW ITEM! Description Denim Apron w/ Chest Pocket SHOP-APRON-PR $7.99 Denim Apron w/ Waist Pocket SHOP-APRON-E $ Master Catalog 453 C CARIDE INSERTS DEURRING

186 CHUCK JAWS LATHE WORKHOLDING COUNTERSINKS CARIDE COUNTERSINKS Manufactured from premium sub-micron carbide with 10 cobalt Sizes 1/4 diameter and smaller are solid carbide Sizes 3/8 and larger are composed of hardened steel shanks and induction brazed heads to insure a solid, safe and secure bond Made in C CHATTERLESS! Carbide Countersinks At A High Speed Steel! MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Cutter SINGLE FLUTE 60 Angle 82 Angle 90 Angle Master Catalog 100 Angle 120 Angle 1/8 1/8 1-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $6.38 3/16 3/16 2 MO-CC MO-CC MO-CC MO-CC MO-CC $9.90 1/4 1/4 2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /16 1/4 2-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 1/4 2-3/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 1/4 2-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 3/8 2-5/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /4 3/8 2-7/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 1/2 3 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 3 MO-CC MO-CC MO-CC MO-CC MO-CC $ /4 3/4 3-3/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 3/4 3-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ FLUTE Cutter 60 Angle 82 Angle 90 Angle 100 Angle 120 Angle 1/8 1/8 1-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $6.38 3/16 3/16 2 MO-CC MO-CC MO-CC MO-CC MO-CC $9.90 1/4 1/4 2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /16 1/4 2-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 1/4 2-3/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 1/4 2-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 3/8 2-5/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /4 3/8 2-7/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 1/2 3 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 3 MO-CC MO-CC MO-CC MO-CC MO-CC $ /4 3/4 3-3/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 3/4 3-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ FLUTE Cutter DIGITAL CALIPERS 60 Angle 82 Angle 90 Angle 100 Angle 120 Angle 1/8 1/8 1-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $6.38 3/16 3/16 2 MO-CC MO-CC MO-CC MO-CC MO-CC $9.90 1/4 1/4 2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /16 1/4 2-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 1/4 2-3/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 1/4 2-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 3/8 2-5/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /4 3/8 2-7/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /8 1/2 3 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 3 MO-CC MO-CC MO-CC MO-CC MO-CC $ /4 3/4 3-3/8 MO-CC MO-CC MO-CC MO-CC MO-CC $ /2 3/4 3-1/2 MO-CC MO-CC MO-CC MO-CC MO-CC $ Direct inch/metric conversion. Resolution:.0005"/.01mm Large easy-to-read LCD display. Includes shop hardened case. Range Accuracy 0 6".001"/.02mm FOW-P $ ".0015"/.03mm FOW-P $ ".0015"/.03mm FOW-P $ IP54.001"/.02mm FOW-P $94.50 Replacement attery FOW-P $5.50 DIGIT COUNTER MICROMETERS Digital counter Resolution:.0001 (using vernier) Microfine graduations on satin chrome Carbide tipped measuring faces Positive locking nut on spindle Sizes over 1 include standard Range 0-1" FOW-P $ " FOW-P $ " FOW-P $ FOW-P $66.50

187 COUNTERORES PRECISION CAP SCREW KOUNTERORES M35 Cobalt-3 Flute Integral pilot, stright shank, CNC precision ground cobalt HSS M35 cobalt: HSS, 6% tungsten, 5% moly, 5% cobalt for long tool life in all type of materials High performance cutting action due to secondary relief behind cutting edge margin Optimized helix for chip evacuation-chips flow away from cut without wrapping around tool Made in the PRECISION CAP SCREW KOUNTERORE SETS 7 Piece Set Contains: #6,#8,#10,1/4,5/16,3/8, 1/2 Nominal #6,#8,#10,1/4,5/16,3/8, 1/2 +1/64 O/S #6,#8,#10,1/4,5/16,3/8, 1/2 +1/32 O/S Assembly Criteria CloseFit KEO $ /64" Clearance 1/32" Clearance INDEXALE INSERT PILOTLESS COUNTERORES 2 flute design All tools feature 1/2 shank : 3.2 Inserts sold separately KEO $ KEO $ Counterbore. Screw Size Assembly Criteria Pilot. A C bore. C. D Product #4 CloseFit /32 KEO $34.94 #4 1/64"Clearance /32 KEO $34.94 #4 1/32"Clearance /32 KEO $34.94 #5 CloseFit /16 KEO $37.26 #5 1/64"Clearance /16 KEO $37.26 #5 1/32"Clearance /16 KEO $37.26 #6 CloseFit /32 KEO $41.10 #6 1/64"Clearance /32 KEO $41.10 #6 1/32"Clearance /32 KEO $41.10 #8 CloseFit /4 KEO $42.17 #8 1/64"Clearance /4 KEO $42.17 #8 1/32"Clearance /4 KEO $42.17 #10 CloseFit /32 KEO $44.37 #10 1/64"Clearance /32 KEO $44.37 #10 1/32"Clearance /32 KEO $ /4 CloseFit /16 KEO $ /4 1/64"Clearance /16 KEO $ /4 1/32"Clearance /16 KEO $ /16 CloseFit /8 KEO $ /16 1/64"Clearance /8 KEO $ /16 1/32"Clearance /8 KEO $ /8 CloseFit /2 KEO $ /8 1/64"Clearance /2 KEO $ /8 1/32"Clearance /2 KEO $ /16 CloseFit /2 KEO $ /16 1/64"Clearance /2 KEO $ /16 1/32"Clearance /2 KEO $ /2 CloseFit /2 KEO $ /2 1/64"Clearance /2 KEO $ /2 1/32"Clearance /2 KEO $ /8 CloseFit /8 KEO $ /8 1/64"Clearance /8 KEO $ /8 1/32"Clearance /8 KEO $ /4 CloseFit /4 KEO $ /4 1/32"Clearance /4 KEO $ /8 CloseFit /8 KEO $ /8 1/32"Clearance /8 KEO $ CloseFit KEO $ /32"Clearance KEO $ Min. Cutting. NEW ITEM! 5/ INC-625S-ET $ / INC-688S-ET $ / INC-750S-ET $ / INC-812S-ET $ / INC-875S-ET $ / INC-938S-ET $ Insert Reference CCMT-215 Screw $2.75 each (sold in packages of 10) Torx Wrench $4.25 each INSERTS Insert I.C. T R Grade Coating Application Reference CCMT T6030 Tin Stainless TO-4917 $4.44 CCMT T9025 Tin Steels TO-3500 $4.60 CARIDE INSERTS DEURRING CCMT CV6 Tin Steels, Cast Iron ET-4917 $6.54 CCMT CS2 Uncoated Aluminum ET-3500 $5.58 CCMT AH120 TiAlN Super Alloys, Steels, Stainless TO-3806 $4.44 CCMT AH120 TiAlN Super Alloys, Steels, Stainless TO-3817 $ Master Catalog 455

188 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD CHAMFER MILLS/FLY CUTTERS INDEXALE CHAMFER MILLS Can be used for countersinking, ID chamfering and facing, as well as exterior chamfering Features Weldon shank Metric sizes also available 16mm paralellogram insert provides for extra length of cut All holders use same insert (Insert sold separately) Min Max.. Weldon Chamfer Angle FLYCUTTER HEADS Included Angle No. of Flutes Depth of Cut Chamfer Mill / CHM ET $ / CHM ET $ / CHM ET $ / CHM ET $ CHM ET $ CHM ET $ CHM ET $ CHM ET $ / CHM ET $ / CHM ET $ / CHM ET $ / CHM ET $ / CHM ET $ / CHM ET $ / CHM ET $ / CHM ET $ REVERSE SPOT FACERS Made from HSS Standard.030 radius Pilots are 6 Other radii and pilot sizes available odies Pilot Vibra-core design with 1/2 tool bit capacity Uses larger 1/2 and 3/8 tool bits for larger cuts Larger 1/4-20 set screws Heat treated and balanced Sizes available: 1-1/2, 2 and 2-1/2 diameter Master Catalog Pilot Insert For Steels/ Stainless APKT1604PDTR-LA $8.83 EACH 1/4 3/32 RSF ET $ /8 1/4 RSF ET $ /4 1/8 RSF ET $ /8 5/16 RSF ET $ /16 1/8 RSF ET $ /16 1/4 RSF ET $ /16 5/32 RSF ET $ /16 5/16 RSF ET $ /8 5/32 RSF ET $ /4 1/4 RSF ET $ /8 3/16 RSF ET $ /4 5/16 RSF ET $ /16 5/32 RSF ET $ /8 5/16 RSF ET $ /16 3/16 RSF ET $ /8 3/8 RSF ET $ /2 3/16 RSF ET $ /16 RSF ET $ /2 1/4 RSF ET $ /8 RSF ET $ /16 3/16 RSF ET $ /4 3/8 RSF ET $ /16 1/4 RSF ET $ /4 1/2 RSF ET $70.38 Pilots Inserts For Aluminum APGT1604ALU-LA $9.56 EACH Screw $2.50 ea Torx Wrench $4.25 ea 3/32 P ET $6.60 1/8 P ET $6.74 5/32 P ET $7.02 3/16 P ET $7.82 1/4 P ET $7.86 5/16 P ET $9.36 3/8 P ET $ /2 P ET $22.56 Size 1-1/2 SIE-FC-1.5 $ SIE-FC-2.0 $ /2 SIE-FC-2.5 $41.16 Set SIE-FC-3S $105.92

189 HIGH PERFORMANCE TAPS SOWA HIGH PERFORMANCE TAPS Sowa High Performance Taps help you take the guesswork out of tap selection. Taps are color-coded to ensure the proper selection for your application. C lue Ring: For general ductile materials including aluminum, low and medium carbon steels, brass, copper and cast iron Yellow Ring: For tough materials including stainless steel, medium grade and alloyed high carbon steel, aluminum and titanium Orange Ring: Superior geometry and design for Stainless Steels Red Ring: Powdered metal ideal for nickel alloys, tool steels, stainless steels and titanium HSSE-V3 TAPS SPIRAL POINT & SPIRAL FLUTE Machine Screw and Fractional Sizes lue Ring Designed for high-speed tapping applications. Developed to withstand the high stress and high heat associated with high-speed CNC production tapping. Features a unique free-cutting design with a special tempering and geometry for long tool life. Applications and Features: Used in general machine tapping applications for mild carbon steels such as 1018, 1010, 1035,1045,1050 and 1065 Up to 25 HRC Metric Sizes Also Available Materials Group Low carbon Medium carbon Sub- Group Condition Spiral Point Spiral Flute Cutting Conditions Hardness (HRC) Cutting Speed (FPM) 1018, 1010, Normalized < , 1050, Normalized < Aluminum Unalloyed, cast rass/ Copper Cast iron As cast < SPIRAL POINT SPIRAL FLUTE Tap TPI Thread Thread No. of No. Of Limits Len. Flutes Flutes NC 4 40 H2 1-7/ SOWA $ SOWA $ H SOWA $ SOWA $ H3 2-1/ SOWA $ SOWA $ H3 2-3/ SOWA $ H3 2-3/ SOWA $ SOWA $ H3 2-3/ SOWA $ /4 20 H3 2-1/ SOWA $ /4 20 H3 2-1/ SOWA $ SOWA $ /16 18 H3 2-23/ SOWA $ /16 18 H3 2-23/ SOWA $ SOWA $ /8 16 H3 2-15/ SOWA $ /8 16 H3 2-15/ SOWA $ SOWA $ /16 14 H3 3-5/ SOWA $ SOWA $ /2 13 H3 3-3/ SOWA $ SOWA $ /8 11 H3 3-13/ SOWA $ SOWA $ /4 10 H3 4-1/ SOWA $ SOWA $ /8 9 H4 4-11/ SOWA $ SOWA $ H4 5-1/ SOWA $ SOWA $ /8 7 H4 5-7/ SOWA $ SOWA $ /4 7 H4 5-3/ SOWA $ SOWA $ /8 6 H4 6-1/ SOWA $ SOWA $ /2 6 H4 6-3/ SOWA $ SOWA $ NF 6 40 H SOWA $ H3 2-3/ SOWA $ H3 2-3/ SOWA $ SOWA $ /4 28 H3 2-1/ SOWA $ /4 28 H3 2-1/ SOWA $ SOWA $ /16 24 H3 2-23/ SOWA $ /16 24 H3 2-23/ SOWA $ SOWA $ /8 24 H3 2-15/ SOWA $ /8 24 H3 2-15/ SOWA $ SOWA $ /16 20 H3 3-5/ SOWA $ /2 20 H3 3-3/ SOWA $ SOWA $ /8 18 H3 3-13/ SOWA $ SOWA $ /4 16 H3 4-1/ SOWA $ SOWA $ /8 14 H4 4-11/ SOWA $ SOWA $ H4 5-1/ SOWA $ SOWA $ /8 12 H4 5-7/ SOWA $ SOWA $ /4 12 H4 5-3/ SOWA $ SOWA $ /8 12 H4 6-1/ SOWA $ SOWA $ /2 12 H4 6-3/ SOWA $ SOWA $ Master Catalog 457 CARIDE INSERTS DEURRING

190 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD HIGH PERFORMANCE TAPS HSSE-V3 3% Vanadium Machine Screw and Fractional Sizes Yellow Ring-Hardened Tool Steels Orange Ring-Stainless Steels Designed for high-speed tapping applications. Developed to withstand the high stress and high heat associated with high-speed CNC production tapping. Features a unique freecutting design with a special tempering and geometry which contributes to extra tool life. Applications and Features: Yellow Ring: Superior performance in hardened tool steels such as 4140, 4340, H13 & D2 Up to 35 HRC Metric Sizes Also Available Orange Ring: For STAINLESS STEELS Up to 35 HRC Straight Tap Holders Are On Page 255 ilz Style Tap Adapters Are On Page 256 Spiral Point Spiral Flute YELLOW RING SPIRAL POINT SPIRAL FLUTE Tap TPI No. Of Flutes Thread Limits Master Catalog Thread Len. No. Of Flutes Thread Len. NC H2 1-3/4.433 SOWA $ SOWA $ H2 1-13/ SOWA $ SOWA $ H2 1-7/8.433 SOWA $ SOWA $ *H3 1-7/8.433 SOWA * $ SOWA * $ H SOWA $ SOWA $ H3 2-1/8.512 SOWA $ SOWA $ H3 2-3/8.512 SOWA $ SOWA $ H3 2-3/8.512 SOWA $ / H3 2-1/2.630 SOWA $ SOWA $ / H3 2-23/ SOWA $ SOWA $ / H3 2-15/ SOWA $ SOWA $ / H3 3-5/ SOWA $ SOWA $ / H3 3-3/8.945 SOWA $ SOWA $ / H3 3-13/ SOWA $ SOWA $ / H3 4-1/ SOWA $ SOWA $ /8 9 3 H4 4-11/ SOWA $ SOWA $ H4 5-1/ SOWA $ SOWA $ /8 7 4 H4 5-7/ SOWA $ SOWA $ /4 7 4 H4 5-3/ SOWA $ SOWA $ /8 6 4 H4 6-1/ SOWA $ SOWA $ /2 6 4 H4 6-3/ SOWA $ SOWA $ NF H SOWA $ H3 2-3/8.512 SOWA $ SOWA $ / H3 2-1/2.630 SOWA $ SOWA $ / H3 2-23/ SOWA $ SOWA $ / H3 2-15/ SOWA $ SOWA $ / H3 3-5/ SOWA $ / H3 3-3/8.945 SOWA $ SOWA $ / H3 3-13/ SOWA $ SOWA $ / H3 4-1/ SOWA $ SOWA $ / H4 4-11/ SOWA $ SOWA $ H4 5-1/ SOWA $ SOWA $ H4 5-1/ SOWA $ SOWA $ / H4 5-7/ SOWA $ SOWA $ / H4 5-3/ SOWA $ SOWA $ / H4 6-1/ SOWA $ SOWA $ / H4 6-3/ SOWA $ SOWA $ ORANGE RING SPIRAL POINT SPIRAL FLUTE Tap TPI No. Of Flutes Thread Limits Thread Len. No. Of Flutes Thread Len. NC H2 1-7/8.433 SOWA $ SOWA $ H SOWA $ SOWA $ H3 2-1/8.512 SOWA $ SOWA $ H3 2-3/8.512 SOWA $ SOWA $ / H3 2-1/2.630 SOWA $ SOWA $ / H3 2-23/ SOWA $ SOWA $ / H3 2-15/ SOWA $ SOWA $ / H3 3-5/ SOWA $ SOWA $ / H3 3-3/8.945 SOWA $ SOWA $ / H3 3-13/ SOWA $ SOWA $ / H3 4-1/ SOWA $ SOWA $ /8 9 3 H4 4-11/ SOWA $ SOWA $ H4 5-1/ SOWA $ SOWA $ NF H3 2-3/8.512 SOWA $ SOWA $ / H3 2-1/2.630 SOWA $ SOWA $ / H3 2-23/ SOWA $ SOWA $ / H3 2-15/ SOWA $ SOWA $ / H3 3-5/ SOWA $ / H3 3-3/8.945 SOWA $ SOWA $ / H3 3-13/ SOWA $ SOWA $ / H3 4-1/ SOWA $ SOWA $ / H4 4-11/ SOWA $ SOWA $ H4 5-1/ SOWA $ SOWA $ C

191 HIGH PERFORMANCE TAPS P-HSS POWDERED METAL TAPS Machine Screw & Fractional Sizes Red Ring Applications and Features: Full Line Available! Please call for more information. C Red Ring: Ideal for heat resistant materials, high strength stainless steel and titanium alloys as well as other high tensile steels and alloys including tool steel and nickel alloys Up to 48 HRC Spiral Point Spiral Flute SPIRAL FLUTE TAPS For Aluminum Tap TPI No. Of Flutes Thread Limits Thread Len. SPIRAL POINT No. Of Flutes Thread Len. SPIRAL FLUTE NC H2 1-7/8.433 SOWA $ SOWA $ H2 1-15/ SOWA $ H SOWA $ SOWA $ H3 2-1/8.512 SOWA $ SOWA $ H3 2-3/8.512 SOWA $ SOWA $ / H3 2-1/2.630 SOWA $ SOWA $ / H3 2-23/ SOWA $ SOWA $ / H3 2-15/ SOWA $ SOWA $ / H3 3-5/ SOWA $ SOWA $ / H3 3-3/8.945 SOWA $ SOWA $ / H3 3-13/ SOWA $ SOWA $ / H3 4-1/ SOWA $ SOWA $ NF H3 2-3/8.512 SOWA $ SOWA $ / H3 2-1/2.630 SOWA $ SOWA $ / H3 2-23/ SOWA $ SOWA $ / H3 2-15/ SOWA $ SOWA $ / H3 3-5/ SOWA $ SOWA $ / H3 3-3/8.945 SOWA $ SOWA $ / H3 3-13/ SOWA $ SOWA $ / H3 4-1/ SOWA $ SOWA $ NEW ITEM! Recommended for all types of aluminum alloys Premium powder metal high speed steel right finish Designed for tapping blind holes-spiral flutes draw the chips out of the hole HSSE-V3 S.T.I. TAPS SCREW THREAD INSERT 45 Spiral Flute Taps Tap STI taps combine special geometry & surface finish for tapping in Aluminum and other non-ferrous materials for screw thread insert applications. TPI No. Of Flutes Thread Limits Thread Length Thread Length NC H2 1-7/8.250 SOWA $ /64 MCT $ H SOWA $ /64 MCT $ H3 2-1/8.313 SOWA $ /64 MCT $ H3 2-3/8.417 SOWA $ /32 MCT $ / H3 2-1/2.500 SOWA $ /16 MCT $ / H3 2-23/ SOWA $ /32 MCT $ / H3 2-15/ SOWA $ /64 MCT $25.42 NF H3 2-3/8.417 SOWA $ /32 MCT $ / H3 2-1/2.500 SOWA $ /16 MCT $ / H3 2-23/ SOWA $ /32 MCT $ / H3 2-15/ SOWA $ /64 MCT $25.42 Tap TPI No. Of Flutes Master Catalog 459 Thread Length NC /8.250 SOWA $ SOWA $ /8.313 SOWA $ /8.417 SOWA $ / /2.500 SOWA $ / / SOWA $ / / SOWA $22.88 NF /8.417 SOWA $ / /2.500 SOWA $ / / SOWA $ / / SOWA $22.88 CARIDE INSERTS DEURRING

192 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD HIGH PERFORMANCE TAPS-METRIC HSSE-V3 METRIC TAPS SPIRAL POINT & SPIRAL FLUTE lue Ring Designed for high-speed tapping applications. Developed to withstand the high stress and high heat associated with high-speed CNC production tapping. Features a unique freecutting design with a special tempering and geometry which contributes to extra tool life. Applications and Features: Used in general machine tapping applications for mild carbon steels such as 1018, 1010, 1035,1045,1050 and 1065 Up to 25 HRC HSSE-V3 3% Vanadium Metric Taps Orange Ring Designed for high-speed tapping applications. Developed to withstand the high stress and high heat associated with high-speed CNC production tapping. Features a unique freecutting design with a special tempering and geometry which contributes to extra tool life. Applications and Features: Orange Ring: For STAINLESS STEELS Up to 35 HRC Spiral Point Spiral Flute Full Line Available! Please call for more information. HIGH PERFORMANCE TAPS For Hard Materials Plug Style-Steam Oxide Finish Recommended for harder 32Rc-45Rc materials including steel alloys, titanium alloys, nickel base high temp alloys, tool and mold steels and stainless steels Designed for tapping through holes CNC reduced neck design Premium powder metallurgy high speed steel, steam oxide finish NEW ITEM! Nominal Size & Pitch No. of Flutes Thread Limits Master Catalog Thread Length SPIRAL POINT SPIRAL FLUTE M2 X.4 2 D3 1-3/4.433 SOWA $ M2.5 X.45 2 D3 1-13/ SOWA $ M3 X.5 3 D3 1-15/ SOWA $9.60 SOWA $16.00 M3.5 X.6 3 D SOWA $7.68 SOWA $16.00 M4 X.7 3 D4 2-1/8.512 SOWA $8.00 SOWA $16.00 M4.5 X.75 3 D4 2-3/8.512 SOWA $ M5 X.8 3 D4 2-3/8.512 SOWA $8.80 SOWA $16.00 M6 X 1 3 D5 2-1/2.630 SOWA $8.96 SOWA $16.00 M7 X 1 3 D5 2-23/ SOWA $11.28 SOWA $19.76 M8 X 1 3 D5 2-23/ SOWA $11.28 SOWA $19.76 M8 X D5 2-23/ SOWA $11.28 SOWA $19.76 M10 X D5 2-15/ SOWA $16.32 SOWA $29.44 M10 X D6 2-15/ SOWA $16.32 SOWA $29.44 M12 X D5 3-3/8.945 SOWA $20.40 SOWA $32.16 M12 X D6 3-3/8.945 SOWA $ M14 X D6 3-19/ SOWA $30.48 SOWA $43.20 M14 X 2 3 D7 3-19/ SOWA $30.48 SOWA $43.20 M16 X D6 3-13/ SOWA $35.84 SOWA $51.52 M16 X 2 3 D7 3-13/ SOWA $35.84 SOWA $51.52 M18 X D6 4-1/ SOWA $46.72 SOWA $74.48 M18 X D7 4-1/ SOWA $46.72 SOWA $74.48 M20 X D5 4-15/ SOWA $57.20 SOWA $ M20 X D6 4-15/ SOWA $57.20 SOWA $ Nominal Size & Pitch Spiral Point No. of Flutes Thread Limits Thread Length Spiral Flute SPIRAL POINT SPIRAL FLUTE M3 X.5 3 D3 1-15/ SOWA $10.56 SOWA $17.76 M4 X.7 3 D4 2-1/8.512 SOWA $8.48 SOWA $17.76 M5 X.8 3 D4 2-3/8.512 SOWA $9.92 SOWA $17.76 M6 X 1 3 D5 2-1/2.630 SOWA $9.92 SOWA $17.76 M8 X D5 2-23/ SOWA $12.48 SOWA $21.76 M10 X D5 2-15/ SOWA $18.00 SOWA $32.40 M10 X D6 2-15/ SOWA $18.00 SOWA $32.40 M12 X D6 3-3/8.945 SOWA $22.48 SOWA $35.52 M14 X 2 3 D6 3-19/ SOWA $33.60 SOWA $47.52 M16 X 2 3 D7 3-13/ SOWA $39.44 SOWA $56.72 M18 X D7 4-1/ SOWA $55.68 SOWA $ M20 X D6 4-1/ SOWA $66.64 SOWA $ M22 X D6 4-11/ SOWA $77.68 SOWA $ M24 X 3 3 D7 4-29/ SOWA $ SOWA $ Nominal Size & Pitch No. of Flutes Thread Limits Thread Length SPIRAL POINT SPIRAL FLUTE M3 X.5 3* D3 5/ /16 MCT $25.13 MCT $33.65 M4 X.7 3* D4 3/8 2-1/8 MCT $21.27 MCT $26.81 M5 X.8 3 D4 1/2 2-3/8 MCT $23.82 MCT $29.69 M6 X 1 3 D5 5/8 2-1/2 MCT $29.69 MCT $30.20 M8 X 1 3 D5 11/ /32 MCT $31.83 MCT $34.82 M8 X D5 11/ /32 MCT $31.83 MCT $34.82 M10 X D6 3/4 2-15/16 MCT $47.06 MCT $53.58 M12 X D5 15/16 3-3/8 MCT $50.40 MCT $61.94 M12 X D6 15/16 3-3/8 MCT $52.92 MCT $61.94 *2 Flutes on Spiral Flute Taps C

193 HAND TAPS HAND TAPS Fractional Sizes Standard HSS, Ground Thread Hand taps are the most commonly used general purpose tap. They are recommended for tapping free machining steels, stainless steels, aluminum, zinc and ductile material. Hand taps are utilized in either through or blind hole tapping. FEATURES: Ground thread Right hand HSS M2 1/4 thru 1-1/2 have 4 flutes 1-5/8 and larger have 6 flutes CAM-LOCKING TAP WRENCH FEATURES: Fits wide range of tap sizes: 1/8" to 1/2" (M3 to M12) Patented Revolutionary Cam-Lock System Quick-action clamping for easy replacement Taps will never release during use Heavy-duty design for reliability and long life Handles extreme torque Can be used as a hand drill for sizes: 1/16" to 5/16" 3-Times The Range Of Most Tap Wrenches! HAND TAPS Machine Screw Sizes Standard HSS, Ground Thread Hand taps are the most commonly used general purpose tap. They are recommended for tapping free machining steels, stainless steels, aluminum, zinc and ductile material. Hand taps are utilized in either through or blind hole tapping. FEATURES: Ground thread Right hand HSS M2 1/4 thru 1-1/2 have 4 flutes 1-5/8 and larger have 6 flutes NEW ITEM! Full Line Available! Please call for more information. NEW ITEM! Quick Release Cam! Fast & Tight! Change Taps Fast! Tap-X Tap Wrench # FOW-P $35.00 Size H Limit Taper Plug ottom Master Catalog 461 C 1/4-20 H3 2-1/2 TMX TMX TMX $2.47 1/4-28 H3 2-1/2 TMX TMX TMX $2.47 5/16-18 H3 2-23/32 TMX TMX TMX $2.82 5/16-24 H3 2-23/32 TMX TMX TMX $2.87 3/8-16 H3 2-15/16 TMX TMX TMX $3.22 3/8-24 H3 2-15/16 TMX TMX TMX $3.30 7/16-14 H3 3-5/32 TMX TMX TMX $5.36 7/16-20 H3 3-5/32 TMX TMX TMX $5.36 1/2-13 H3 3-3/8 TMX TMX TMX $7.35 1/2-20 H3 3-3/8 TMX TMX TMX $7.35 9/16-12 H3 3-19/32 TMX TMX TMX $ /16-18 H3 3-19/32 TMX TMX TMX $ /8-11 H3 3-13/16 TMX TMX TMX $ /8-18 H3 3-13/16 TMX TMX TMX $ /4-10 H3 4-1/4 TMX TMX TMX $ /4-16 H3 4-1/4 TMX TMX TMX $ /8-9 H4 4-11/16 TMX TMX TMX $ /8-14 H4 4-11/16 TMX TMX TMX $ H4 5-1/8 TMX TMX TMX $ H4 5-1/8 TMX TMX TMX $ H4 5-1/8 TMX TMX TMX $ /8-7 H4 5-7/16 TMX TMX TMX $ /8-8 H4 5-7/16 TMX TMX TMX $ /8-12 H4 5-7/16 TMX TMX TMX $ /4-7 H4 5-3/4 TMX TMX TMX $ /4-8 H4 5-3/4 TMX TMX TMX $ /4-12 H4 5-3/4 TMX TMX TMX $ /8-6 H4 6-1/16 TMX TMX TMX $ /8-8 H4 6-1/16 TMX TMX TMX $ /8-12 H4 6-1/16 TMX TMX TMX $ /2-6 H4 6-3/8 TMX TMX TMX $ /2-8 H4 6-3/8 TMX TMX TMX $ /2-12 H4 6-3/8 TMX TMX TMX $ /8-8 H4 6-11/16 TMX TMX TMX $ /8-12 H4 5 TMX TMX TMX $ Size H Limit Taper Plug NEW ITEM! ottom 1-72 H2 1-11/16 TMX TMX TMX $ H2 1-3/4 TMX TMX TMX $ H2 1-3/4 TMX TMX $ H2 1-13/16 TMX TMX TMX $ H2 1-13/16 TMX TMX TMX $ H2 1-7/8 TMX TMX TMX $ H2 1-7/8 TMX TMX TMX $ H2 1-15/16 TMX TMX TMX $ H2 1-15/16 TMX TMX TMX $ H2 2 TMX $ H3 2 TMX TMX TMX $ H2 2 TMX TMX TMX $ H3 2-1/8 TMX TMX TMX $ H2 2-1/8 TMX $ H3 2-3/8 TMX TMX TMX $ H3 2-3/8 TMX TMX TMX $ H3 2-3/8 TMX TMX TMX $ H3 2-3/8 TMX TMX $3.12 CARIDE INSERTS DEURRING

194 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SPIRAL POINTED HAND TAPS SPIRAL POINT TAPS Fractional & Machine Screw Sizes Standard HSS, Ground Thread Plug Chamfer Right hand cut Ground thread Fractional & machine screw sizes HSS M2 1/4 and 5/16 have 2 flutes 3/8 thru 1 have 3 flutes Full Line Available! Please call for more information. STRAIGHT PIPE TAPS Ground Thread-High Speed Steel Ground thread HSS NPS Taps produce straight pipe threads for low pressure applications NPSF Dryseal Taps produce threads where a tight seal is achieved during assembly by metal-to-metal contact. For applications requiring a tight seal without the use of thread sealants Size NEW ITEM! PIPE TAPS-STRAIGHT & TAPER Ground Thread-High Speed Steel HSS, Ground thread NPS Taps produce straight pipe threads for low pressure applications NPSF Dryseal Taps produce threads where a tight seal is achieved during assembly by metal-to-metal contact TPI No. Of Flutes Fractional Sizes Machine Screw Sizes Size H Plug H Plug Size Limit Limit 1/4-20 H3 2-1/2 TMX $ H2 1-5/8 TMX $8.03 1/4-28 H3 2-1/2 TMX $ H2 1-11/16 TMX $7.51 5/16-18 H3 2-23/32 TMX $ H2 1-11/16 TMX $7.51 5/16-24 H3 2-23/32 TMX $ H2 1-3/4 TMX $6.41 3/8-16 H3 2-5/16 TMX $ H2 1-3/4 TMX $6.41 3/8-24 H3 2-5/16 TMX $ H2 1-3/16 TMX $5.08 7/16-14 H3 3-5/32 TMX $ H2 1-3/16 TMX $5.08 7/16-20 H3 3-5/32 TMX $ H2 1-7/8 TMX $3.43 1/2-13 H3 3-3/8 TMX $ H2 7-7/8 TMX $3.43 1/2-20 H3 3-3/8 TMX $ H2 1-15/16 TMX $3.43 9/16-12 H3 3-19/32 TMX $ H2 1-15/16 TMX $3.43 9/16-18 H5 3-19/32 TMX $ H3 2 TMX $3.08 5/8-11 H3 3-13/16 TMX $ H13 2 TMX $3.68 5/8-18 H3 3-13/16 TMX $ H2 2 TMX $3.08 3/4-10 H3 4-1/4 TMX $ H3 2-1/8 TMX $3.08 3/4-16 H3 4-1/4 TMX $ H13 2-1/8 TMX $3.68 7/8-9 H4 4-11/16 TMX $ H2 2-1/8 TMX $3.08 7/8-14 H6 4-11/16 TMX $ H3 2-3/8 TMX $ H4 5-1/8 TMX $ H3 2-3/8 TMX $ H4 5-1/8 TMX $ H3 2-3/8 TMX $ H4 5-1/8 TMX $ H3 2-3/8 TMX $3.43 Thread Length Master Catalog Sizse No. of Flutes Thread Length NPS NPSF (Sm Shk) 4 3/4 2-1/8 MCT MCT $ /8-27 (Lg Shk) 4 3/4 2-1/8 MCT MCT $ / /16 2-7/16 MCT MCT $ / /16 2-9/16 MCT MCT $ / /8 3-1/8 MCT MCT $ / /8 3-1/4 MCT MCT $ / /4 3-3/4 MCT $ NPT NEW ITEM! TAPER NPTF NPS STRAIGHT NPSF 1/ /8 11/16 I $9.26 I $9.26 I $9.26 1/8(SM)* /8 3/4 I $9.26 I $9.26 I $9.26 1/8(LG)* /8 3/4 I $9.26 I $9.26 I $9.26 I $9.26 1/ /16 1-1/16 I $11.98 I $11.98 I $11.98 I $ / /16 1-1/16 I $14.06 I $14.06 I $14.06 I $ / /8 1-3/8 I $23.17 I $24.45 I $23.17 I $ / /4 1-3/8 I $34.65 I $34.65 I $34.65 I $ / /4 1-3/4 I $72.36 I $72.36 I $ /4 11-1/ /4 I $ I $ I $ /2 11-1/ /4 1-3/4 I $ I $ I $ I $ / /2 1-3/4 I $ I $ I $ / /2 2-9/16 I $ I $ I $ /8 I $ I $ /4 2-3/4 I $1, *SM (small shank) =.3125 and LG (large shank) =.4375 NEW ITEM! C

195 COMINED DRILL AND TAP/STI TAPS COMINATION TAP & DRILL High Speed Steel High Speed Steel, 2 Flute Combined drills and taps will do two operations at one time. Designed so that through-holes up to times the tap diameter can be drilled and tapped at high RPM Will work well in any material where HSS tools will perform Drill points will produce the proper size hole for tapping Full Line Available! Please call for more information. SCREW THREAD INSERT (STI) TAPS Straight Flute & Spiral Point Size UNC UNF /4 5/16 3/8 7/16 1/2 NEW ITEM! Thread Size Thread Length H Limit Size Flute Length Master Catalog 463 C 4-40 NC 9/16 H /4 1-7/8 TMX $ NF 9/16 H /4 1-7/8 TMX $ NC 5/8 H /32 1-5/16 TMX $ NF 5/8 H /32 1-5/16 TMX $ NC 11/16 H /16 2 TMX $ NC 3/4 H /8 2-1/8 TMX $ NF 3/4 H /8 2-1/8 TMX $ NC 7/8 H /32 2-3/8 TMX $ NF 7/8 H /32 2-3/8 TMX $ NC 7/8 H /32 2-3/8 TMX $7.85 1/4-20 NC 15/16 H /32 2-1/2 TMX $7.85 1/4-28 NF 15/16 H /32 2-1/2 TMX $7.85 5/16-18 NC 1-1/8 H /16 3 TMX $8.70 5/16-24 NF 1-1/8 H /16 3 TMX $8.70 3/8-16 NC 1-1/4 H /16 3-1/2 TMX $ /8-24 NF 1-1/4 H /16 3-1/2 TMX $ /16-14 NC 1-7/16 H /8 TMX $ /16-20 NF 1-7/16 H /8 TMX $ /2-13 NC 1-21/32 H /8 4-1/4 TMX $ /2-20 NF 1-21/32 H /8 4-1/4 TMX $17.40 NEW ITEM! TPI STRAIGHT FLUTE SPIRAL POINT H Limit No. of Flutes Thread Length PLUG OTTOM No. of Flutes PLUG 56 H1 3 7/16 1-3/4 MCT MCT $ MCT $ H2 3 7/16 1-3/4 MCT MCT $ MCT $ H1 3 9/16 1-7/8 MCT MCT $ MCT $ H2 3 9/16 1-7/8 MCT MCT $ MCT $ H1 3 5/8 1-15/16 MCT MCT $ MCT $ H2 3 5/8 1-15/16 MCT MCT $ MCT $ H2 3 11/16 2 MCT MCT $ MCT $ H3 3 11/16 2 MCT MCT $ MCT $ H1 3 11/16 2 MCT MCT $ MCT $ H2 3 11/16 2 MCT MCT $ MCT $ H2 3 3/4 2-1/8 MCT MCT $ MCT $ H3 3 3/4 2-1/8 MCT MCT $ MCT $ H2 3 7/8 2-3/8 MCT MCT $ MCT $ H3 3 7/8 2-3/8 MCT MCT $ MCT $ H2 3 7/8 2-3/8 MCT MCT $ MCT $ H3 3 7/8 2-3/8 MCT MCT $ MCT $ H2 3 15/16 2-3/8 MCT MCT $ MCT $ H3 3 15/16 2-3/8 MCT MCT $ MCT $ H /2 MCT MCT $ MCT $ H /2 MCT MCT $ MCT $ H /2 MCT MCT $ MCT $ H /2 MCT MCT $ MCT $ H /8 2-23/32 MCT MCT $ MCT $ H /8 2-23/32 MCT MCT $ MCT $ H /8 2-23/32 MCT MCT $ MCT $ H /8 2-23/32 MCT MCT $ MCT $ H /4 2-15/16 MCT MCT $ MCT $ H /4 2-15/16 MCT MCT $ MCT $ H /4 2-15/16 MCT MCT $ MCT $ H /4 2-15/16 MCT MCT $ MCT $ H /16 3-5/32 MCT MCT $ MCT $ H /16 3-5/32 MCT MCT $ MCT $ H /16 3-5/32 MCT MCT $ MCT $ H /16 3-5/32 MCT MCT $ MCT $ H /32 3-3/8 MCT MCT $ MCT $ H /32 3-3/8 MCT MCT $ MCT $ H /32 3-3/8 MCT MCT $ MCT $ H /32 3-3/8 MCT MCT $ MCT $24.54 CARIDE INSERTS DEURRING

196 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING TAP WRENCHES/TAP ACCESSORIES T-HANDLE TAP WRENCHES T-Handles slide both ways for tightening Spring tension holds handle in desired position Used by toolmakers and mechanics for holding Taps, reamers and other small tools Ratcheting wrenches also available Tap Capacity 1/16" to 5/32 PEC $6.79 5/32" to 1/4 PEC $7.28 1/4" to 1/2 PEC $7.76 T-HANDLE TAP WRENCH SETS Self-centering, hardened steel jaws and knurled chuck sleeve For holding taps, reamers, screw extractors, hand turned tools and drill bits The front has machine screw size tap drill chart for recommended 75% depth thread REVERSILE SET includes 2 ratcheting tap wrenches (No. 0 to 1/4 and No. 12 to 1/2 tap capacity) PROFESSIONAL SET includes 2 plain tap wrenches (No. 0 to 1/4 and No. 12 to 1/2 tap capacity) Packaged in a sturdy, fitted foamlined plastic case Description Reversible Ratcheting Tap Wrench Set GEN $74.99 Professional Tap Wrench Set GEN $29.99 THREAD REPAIR FILES T-HANDLE TAP WRENCHES Ratcheting Type Ratcheting type Made of tool steel, hardened and ground Used for holding taps and reamers Tap Capacity ody Length MICHIGAN DRILL EVERYDAY VALUE 1/16-5/32 2-1/8 MICH-TWR-1 $9.78 A $8.99 5/32-1/4 2-5/8 MICH-TWR-2 $10.95 A $9.99 1/4-1/2 3-1/2 MICH-TWR-3 $14.34 A $11.99 ADJUSTALE TAP & REAMER WRENCHES Size FEATURES: Knurled steel handles Hardened and tempered jaws Can be used for taps or reamers Frac Taps #0 0-5/16 5 A $4.99 #1-1/2 1/32-1/2 8 A $5.49 #3 3/16-3/4 15 A $10.49 #4 7/ A $16.99 #6 5/32-3/4 - MICH-TW6 $28.31 #7 1/4-1 1/8 - MICH-TW7 $31.56 #7-5 1/2-1 3/8 - MICH-TW75 $39.80 SCREW PITCH GAGES rand C EVERYDAY VALUE MICHIGAN DRILL ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Restore damaged external threads on studs, bolts, screws, plumbing pipe and pipe fittings file provides 4 to 8 different thread pitches Restores rusted or corroded fasteners Doubles as a screw pitch gage lack oxide coating prevents rust Thread Pitches 11,12,13,14,16,18,20,24 TPI 7/16 8-1/2 GEN $ ,10,12,16,20,27,28,32 TPI 7/16 8-1/2 GEN $10.49 SCREW EXTRACTOR SET FEATURES: Quick and easy removal of broken screws, bolts & studs without damaging the threads in the hole Made of chrome-molly steel Supplied with plastic case Choose from Quality Import or Made in model Description rand Import A $6.99 #1-#5 & 1/8"-3/4" Set A $15.99 Quickly determine the pitch of various threads English (inch) gage measures V, Unified and American National 60 threads Narrow designed blades permit use for internal and external screw threads Locking device at each end to secure all blades for storage or position an individual blade for use blade clearly marked with proper thread size lades protected in sturdy steel case Type Of lades No. Of Pitches English Gage English/ Metric Metric Gage Master Catalog No. Of Groups lades Included rand PEC PEC-5651 $ inch GENERAL GEN $45.97 STARRETT STR $ inch mm PEC PEC-5629 $ mm PEC PEC-5625 $ mm PEC PEC-5617 $13.53

197 ROUND ADJUSTALE SPLIT DIES ROUND ADJUSTALE SPLIT DIES Right hand High speed steel-m2 Also available with special threads per inch and left hand NEW ITEM! Straight Pipe NPS Size TPI OD Size TPI OD Taper Pipe NPT Size TPI OD Size TPI OD Size TPI OD National Coarse Thread 3/ I $31.01 National Fine Thread (cont.) # /16 I $8.87 7/8 9 2 I $ / /2 I $16.29 # /16 I $ I $ / /2 I $16.29 # /16 I $ / /2 I $ / /2 I $16.29 # /16 I $ / /2 I $ / /2 I $16.29 # /16 I $ / /2 I $ / /2 I $16.29 # /16 I $ / /2 I $ / /2 I $ / /16 I $ I $ / /2 I $ / /16 I $ /4 7 3 I $ / I $31.01 # I $ /8 6 3 I $ / I $31.01 # I $ /2 6 3 I $ / I $31.01 # I $ /8 5-1/2 3 I $ / I $31.01 # I $ /4 5 3 I $ / I $31.01 # I $ /8 5 3 I $ / I $31.01 # I $ /2 3 I $ / I $ / I $10.37 National Fine Thread 3/ I $ / I $10.37 # /16 I $8.97 7/ I $ / I $10.37 # /16 I $ I $ / I $10.37 # /16 I $ I $ / I $10.37 #* 36 13/16 I $ / /2 I $ / /2 I $16.29 # /16 I $ / /2 I $ / /2 I $16.29 # /16 I $ / /2 I $ / /2 I $ / /16 I $ / /2 I $ / /2 I $ / /16 I $ I $ / /2 I $16.29 # I $ / I $ / /2 I $16.29 # I $ / I $ / /2 I $16.29 # I $ / I $ / /2 I $16.29 # I $ / I $ / I $31.01 # I $ / I $ / I $ / I $ / I $ / I $ / I $ I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ / /2 I $ / I $ / I $ / I $ / I $ / /2 I $ / /2 I $ / /2 I $ / /2 I $ / /2 I $ / /2 I $ / I $ / I $ / I $ / I $ / I $ / I $ / I $ /2 2-1/2 I $ /2 2-1/2 I $ /4 11-1/2 3 I $ /4 11-1/2 3 I $ /2 11-1/2 3 I $ /2 4 I $ /2 8 5 I $ I $ Heavy Duty Die Stocks Additional Sizes & Styles Available! Please Call For More Information! Master Catalog 465 Die 13/16 6-1/4 I $ I $ /2 12 I $ /2 I $ /2 20 I $ I $29.05 CARIDE INSERTS DEURRING

198 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID CARIDE CHUCKING REAMERS SOLID CARIDE CHUCKING REAMERS Straight -Straight Flute C2 Micrograin Carbide FEATURES: Ideal for machining tough materials Cutting flutes are precision ground Higher productivity and faster material removal Higher heat resistance 4 flutes on sizes up to.255 diameter 6 flutes on sizes.255 and above diameter Made in the Dec Master Catalog D TOLERANCES meter. Tolerances.0280 to / to / MORE ITEMS IN STOCK!.0005 Increments In Stock Through.275 meter &.001 Increments From.2580 to.5050 meter! Size LOC Dec. Size LOC Expanded Selection! Dec. Size LOC #70 1/4 1-1/2 MO-CR0280 $ /8 1-1/2 MO-CR0560 $ /2 2 MO-CR0825 $ #69 1/4 1-1/2 MO-CR0292 $ /8 1-1/2 MO-CR0565 $ /2 2 MO-CR0830 $ /4 1-1/2 MO-CR0300 $ /8 1-1/2 MO-CR0570 $ /2 2 MO-CR0835 $ #68 1/4 1-1/2 MO-CR0310 $ /8 1-1/2 MO-CR0575 $ /2 2 MO-CR0840 $ /32 1/4 1-1/2 MO-CR0312 $ /8 1-1/2 MO-CR0580 $ /2 2 MO-CR0845 $ /4 1-1/2 MO-CR0315 $ /8 1-1/2 MO-CR0585 $ /2 2 MO-CR0850 $ #67 1/4 1-1/2 MO-CR0320 $ /8 1-1/2 MO-CR0590 $ /2 2 MO-CR0855 $ /4 1-1/2 MO-CR0325 $ mm 3/8 1-1/2 MO-CR0591 $ #44 1/2 2 MO-CR0860 $ #66 1/4 1-1/2 MO-CR0330 $ #53 3/8 1-1/2 MO-CR0595 $ /2 2 MO-CR0865 $ /4 1-1/2 MO-CR0335 $ /8 1-1/2 MO-CR0600 $ /2 2 MO-CR0870 $ /4 1-1/2 MO-CR0340 $ /8 1-1/2 MO-CR0605 $ /2 2 MO-CR0875 $ /4 1-1/2 MO-CR0345 $ /8 1-1/2 MO-CR0610 $ /2 2 MO-CR0880 $ #65 1/4 1-1/2 MO-CR0350 $ /8 1-1/2 MO-CR0615 $ /2 2 MO-CR0885 $ /4 1-1/2 MO-CR0355 $ /8 1-1/2 MO-CR0620 $ #43 1/2 2 MO-CR0890 $ #64 1/4 1-1/2 MO-CR0360 $ /16 3/8 1-1/2 MO-CR0625 $ /2 2 MO-CR0895 $ /4 1-1/2 MO-CR0365 $ /8 1-1/2 MO-CR0630 $ /2 2 MO-CR0900 $ #63 1/4 1-1/2 MO-CR0370 $ #52 3/8 1-1/2 MO-CR0635 $ /2 2 MO-CR0905 $ /4 1-1/2 MO-CR0375 $ /8 1-1/2 MO-CR0640 $ /2 2 MO-CR0910 $ #62 1/4 1-1/2 MO-CR0380 $ /8 1-1/2 MO-CR0645 $ /2 2 MO-CR0915 $ /4 1-1/2 MO-CR0385 $ /8 1-1/2 MO-CR0650 $ /2 2 MO-CR0920 $ #61 1/4 1-1/2 MO-CR0390 $ /2 1-3/4 MO-CR0655 $ /2 2 MO-CR0925 $ mm 1/4 1-1/2 MO-CR0394 $ /2 1-3/4 MO-CR0660 $ /2 2 MO-CR0930 $ /4 1-1/2 MO-CR0395 $ /2 1-3/4 MO-CR0665 $ #42 1/2 2 MO-CR0935 $ #60 1/4 1-1/2 MO-CR0400 $ #51 1/2 1-3/4 MO-CR0670 $ /32 1/2 2 MO-CR0938 $ /4 1-1/2 MO-CR0405 $ /2 1-3/4 MO-CR0675 $ /2 2 MO-CR0940 $ #59 1/4 1-1/2 MO-CR0410 $ /2 1-3/4 MO-CR0680 $ /2 2 MO-CR0945 $ /4 1-1/2 MO-CR0415 $ /2 1-3/4 MO-CR0685 $ /2 2 MO-CR0950 $ #58 3/8 1-1/2 MO-CR0420 $ /2 1-3/4 MO-CR0690 $ /2 2 MO-CR0955 $ /8 1-1/2 MO-CR0425 $ /2 1-3/4 MO-CR0695 $ #41 1/2 2 MO-CR0960 $ #57 3/8 1-1/2 MO-CR0430 $ #50 1/2 1-3/4 MO-CR0700 $ /2 2 MO-CR0965 $ /8 1-1/2 MO-CR0435 $ /2 1-3/4 MO-CR0705 $ /8 2-1/4 MO-CR0970 $ /8 1-1/2 MO-CR0440 $ /2 1-3/4 MO-CR0710 $ /8 2-1/4 MO-CR0975 $ /8 1-1/2 MO-CR0445 $ /2 1-3/4 MO-CR0715 $ #40 5/8 2-1/4 MO-CR0980 $ /8 1-1/2 MO-CR0450 $ /2 1-3/4 MO-CR0720 $ mm 5/8 2-1/4 MO-CR0984 $ /8 1-1/2 MO-CR0455 $ /2 1-3/4 MO-CR0725 $ /8 2-1/4 MO-CR0985 $ /8 1-1/2 MO-CR0460 $ #49 1/2 1-3/4 MO-CR0730 $ /8 2-1/4 MO-CR0990 $ #56 3/8 1-1/2 MO-CR0465 $ /2 1-3/4 MO-CR0735 $ #39 5/8 2-1/4 MO-CR0995 $ /64 3/8 1-1/2 MO-CR0469 $ /2 1-3/4 MO-CR0740 $ /8 2-1/4 MO-CR1000 $ /8 1-1/2 MO-CR0470 $ /2 1-3/4 MO-CR0745 $ /8 2-1/4 MO-CR1005 $ /8 1-1/2 MO-CR0475 $ /2 1-3/4 MO-CR0750 $ /8 2-1/4 MO-CR1010 $ /8 1-1/2 MO-CR0480 $ /2 1-3/4 MO-CR0755 $ #38 5/8 2-1/4 MO-CR1015 $ /8 1-1/2 MO-CR0485 $ #48 1/2 1-3/4 MO-CR0760 $ /8 2-1/4 MO-CR1020 $ /8 1-1/2 MO-CR0490 $ /2 1-3/4 MO-CR0765 $ /8 2-1/4 MO-CR1025 $ /8 1-1/2 MO-CR0495 $ /2 1-3/4 MO-CR0770 $ /8 2-1/4 MO-CR1030 $ /8 1-1/2 MO-CR0500 $ /2 1-3/4 MO-CR0775 $ /8 2-1/4 MO-CR1035 $ /8 1-1/2 MO-CR0505 $ /2 1-3/4 MO-CR0780 $ #37 5/8 2-1/4 MO-CR1040 $ /8 1-1/2 MO-CR0510 $ /64 1/2 1-3/4 MO-CR0781 $ /8 2-1/4 MO-CR1045 $ /8 1-1/2 MO-CR0515 $ #47 1/2 1-3/4 MO-CR0785 $ /8 2-1/4 MO-CR1050 $ #55 3/8 1-1/2 MO-CR0520 $ mm 1/2 1-3/4 MO-CR0787 $ /8 2-1/4 MO-CR1055 $ /8 1-1/2 MO-CR0525 $ /2 1-3/4 MO-CR0790 $ /8 2-1/4 MO-CR1060 $ /8 1-1/2 MO-CR0530 $ /2 1-3/4 MO-CR0795 $ #36 5/8 2-1/4 MO-CR1065 $ /8 1-1/2 MO-CR0535 $ /2 1-3/4 MO-CR0800 $ /8 2-1/4 MO-CR1070 $ /8 1-1/2 MO-CR0540 $ /2 1-3/4 MO-CR0805 $ /8 2-1/4 MO-CR1075 $ /8 1-1/2 MO-CR0545 $ #46 1/2 1-3/4 MO-CR0810 $ /8 2-1/4 MO-CR1080 $ #54 3/8 1-1/2 MO-CR0550 $ /2 2 MO-CR0815 $ /8 2-1/4 MO-CR1085 $ /8 1-1/2 MO-CR0555 $ #45 1/2 2 MO-CR0820 $ /8 2-1/4 MO-CR1090 $30.33

199 SOLID CARIDE CHUCKING REAMERS SOLID CARIDE CHUCKING REAMERS (continued) Straight -Straight Flute C2 Micrograin Carbide Dec. Size LOC Dec. Size LOC Expanded Selection! Master Catalog 467 Dec. Size LOC MORE ITEMS IN STOCK!.0005 Increments In Stock Through.275 meter &.001 Increments From.2580 to.5050 meter! /64 5/8 2-1/4 MO-CR1094 $ /4 2-1/2 MO-CR1380 $ /8 2-3/4 MO-CR1665 $ /8 2-1/4 MO-CR1095 $ /4 2-1/2 MO-CR1385 $ /8 2-3/4 MO-CR1670 $ #35 5/8 2-1/4 MO-CR1100 $ /4 2-1/2 MO-CR1390 $ /8 2-3/4 MO-CR1675 $ /8 2-1/4 MO-CR1105 $ /4 2-1/2 MO-CR1395 $ /8 2-3/4 MO-CR1680 $ #34 5/8 2-1/4 MO-CR1110 $ /4 2-1/2 MO-CR1400 $ /8 2-3/4 MO-CR1685 $ /8 2-1/4 MO-CR1115 $ #28 3/4 2-1/2 MO-CR1405 $ /8 2-3/4 MO-CR1690 $ /8 2-1/4 MO-CR1120 $ /64 3/4 2-1/2 MO-CR1406 $ #18 7/8 2-3/4 MO-CR1695 $ /8 2-1/4 MO-CR1125 $ /4 2-1/2 MO-CR1410 $ /8 2-3/4 MO-CR1700 $ #33 5/8 2-1/4 MO-CR1130 $ /4 2-1/2 MO-CR1415 $ /8 2-3/4 MO-CR1705 $ /8 2-1/4 MO-CR1135 $ /4 2-1/2 MO-CR1420 $ /8 2-3/4 MO-CR1710 $ /8 2-1/4 MO-CR1140 $ /4 2-1/2 MO-CR1425 $ /8 2-3/4 MO-CR1715 $ /8 2-1/4 MO-CR1145 $ /4 2-1/2 MO-CR1430 $ /64 7/8 2-3/4 MO-CR1719 $ /8 2-1/4 MO-CR1150 $ /4 2-1/2 MO-CR1435 $ /8 2-3/4 MO-CR1720 $ /8 2-1/4 MO-CR1155 $ #27 3/4 2-1/2 MO-CR1440 $ /8 2-3/4 MO-CR1725 $ #32 5/8 2-1/4 MO-CR1160 $ /4 2-1/2 MO-CR1445 $ #17 7/8 2-3/4 MO-CR1730 $ /8 2-1/4 MO-CR1165 $ /4 2-1/2 MO-CR1450 $ /8 2-3/4 MO-CR1735 $ /8 2-1/4 MO-CR1170 $ /4 2-1/2 MO-CR1455 $ /8 2-3/4 MO-CR1740 $ /8 2-1/4 MO-CR1175 $ /4 2-1/2 MO-CR1460 $ /8 2-3/4 MO-CR1745 $ /8 2-1/4 MO-CR1180 $ /4 2-1/2 MO-CR1465 $ /8 2-3/4 MO-CR1750 $ mm 5/8 2-1/4 MO-CR1181 $ #26 3/4 2-1/2 MO-CR1470 $ /8 2-3/4 MO-CR1755 $ /8 2-1/4 MO-CR1185 $ /4 2-1/2 MO-CR1475 $ /8 2-3/4 MO-CR1760 $ /8 2-1/4 MO-CR1190 $ /4 2-1/2 MO-CR1480 $ /8 2-3/4 MO-CR1765 $ /8 2-1/4 MO-CR1195 $ /4 2-1/2 MO-CR1485 $ #16 7/8 2-3/4 MO-CR1770 $ #31 5/8 2-1/4 MO-CR1200 $ /4 2-1/2 MO-CR1490 $ mm 7/8 2-3/4 MO-CR1772 $ /8 2-1/4 MO-CR1205 $ #25 3/4 2-1/2 MO-CR1495 $ /8 2-3/4 MO-CR1775 $ /8 2-1/4 MO-CR1210 $ /4 2-1/2 MO-CR1500 $ /8 2-3/4 MO-CR1780 $ /8 2-1/4 MO-CR1215 $ /4 2-1/2 MO-CR1505 $ /8 2-3/4 MO-CR1785 $ /8 2-1/4 MO-CR1220 $ /4 2-1/2 MO-CR1507 $ /8 2-3/4 MO-CR1790 $ /8 2-1/4 MO-CR1225 $ /4 2-1/2 MO-CR1510 $ /8 2-3/4 MO-CR1795 $ D/P 5/8 2-1/4 MO-CR1230 $ /4 2-1/2 MO-CR1515 $ #15 7/8 2-3/4 MO-CR1800 $ /8 2-1/4 MO-CR1235 $ #24 3/4 2-1/2 MO-CR1520 $ /8 2-3/4 MO-CR1805 $ U/S 5/8 2-1/4 MO-CR1240 $ /4 2-1/2 MO-CR1525 $ /8 2-3/4 MO-CR1810 $ /8 2-1/4 MO-CR1245 $ /4 2-1/2 MO-CR1530 $ /8 2-3/4 MO-CR1814 $ D/P 5/8 2-1/4 MO-CR1247 $ /4 2-1/2 MO-CR1535 $ /8 2-3/4 MO-CR1815 $ /8 5/8 2-1/4 MO-CR1250 $ #23 3/4 2-1/2 MO-CR1540 $ #14 7/8 2-3/4 MO-CR1820 $ /8 2-1/4 MO-CR1255 $ /4 2-1/2 MO-CR1541 $ /8 2-3/4 MO-CR1825 $ O/S 5/8 2-1/4 MO-CR1260 $ /4 2-1/2 MO-CR1545 $ /8 2-3/4 MO-CR1830 $ /8 2-1/4 MO-CR1265 $ /4 2-1/2 MO-CR1550 $ /8 2-3/4 MO-CR1835 $ /8 2-1/4 MO-CR1270 $ /4 2-1/2 MO-CR1555 $ /8 2-3/4 MO-CR1840 $ /8 2-1/4 MO-CR1275 $ /4 2-1/2 MO-CR1560 $ /8 2-3/4 MO-CR1845 $ /8 2-1/4 MO-CR1280 $ /32 3/4 2-1/2 MO-CR1562 $ #13 7/8 2-3/4 MO-CR1850 $ #30 5/8 2-1/4 MO-CR1285 $ /4 2-1/2 MO-CR1565 $ D/P 7/8 2-3/4 MO-CR1855 $ /8 2-1/4 MO-CR1290 $ #22 3/4 2-1/2 MO-CR1570 $ /8 2-3/4 MO-CR1860 $ /8 2-1/4 MO-CR1295 $ mm 3/4 2-1/2 MO-CR1575 $ U/S 7/8 2-3/4 MO-CR1865 $ /8 2-1/4 MO-CR1300 $ /4 2-1/2 MO-CR1580 $ D/P 7/8 2-3/4 MO-CR1870 $ /4 2-1/2 MO-CR1305 $ /4 2-1/2 MO-CR1585 $ /8 2-3/4 MO-CR1872 $ /4 2-1/2 MO-CR1310 $ #21 3/4 2-1/2 MO-CR1590 $ /16 7/8 2-3/4 MO-CR1875 $ /4 2-1/2 MO-CR1315 $ /4 2-1/2 MO-CR1595 $ /8 2-3/4 MO-CR1880 $ /4 2-1/2 MO-CR1320 $ /4 2-1/2 MO-CR1600 $ O/S 7/8 2-3/4 MO-CR1885 $ /4 2-1/2 MO-CR1325 $ /4 2-1/2 MO-CR1605 $ #12 7/8 2-3/4 MO-CR1890 $ /4 2-1/2 MO-CR1330 $ #20 7/8 2-3/4 MO-CR1610 $ /8 2-3/4 MO-CR1895 $ /4 2-1/2 MO-CR1335 $ /8 2-3/4 MO-CR1615 $ /8 2-3/4 MO-CR1900 $ /4 2-1/2 MO-CR1340 $ /8 2-3/4 MO-CR1620 $ /8 2-3/4 MO-CR1905 $ /4 2-1/2 MO-CR1345 $ /8 2-3/4 MO-CR1625 $ #11 7/8 2-3/4 MO-CR1910 $ /4 2-1/2 MO-CR1350 $ /8 2-3/4 MO-CR1630 $ /8 2-3/4 MO-CR1915 $ /4 2-1/2 MO-CR1355 $ /8 2-3/4 MO-CR1635 $ MO-CR1920 $ #29 3/4 2-1/2 MO-CR1360 $ /8 2-3/4 MO-CR1640 $ MO-CR1925 $ /4 2-1/2 MO-CR1365 $ /8 2-3/4 MO-CR1645 $ MO-CR1930 $ /4 2-1/2 MO-CR1370 $ /8 2-3/4 MO-CR1650 $ # MO-CR1935 $ /4 2-1/2 MO-CR1375 $ /8 2-3/4 MO-CR1655 $ MO-CR1940 $ mm 3/4 2-1/2 MO-CR1378 $ #19 7/8 2-3/4 MO-CR1660 $ MO-CR1945 $42.67 D CARIDE INSERTS DEURRING

200 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD SOLID CARIDE CHUCKING REAMERS SOLID CARIDE CHUCKING REAMERS (continued) Straight -Straight Flute C2 Micrograin Carbide Dec. Size LOC Master Catalog Dec. Size LOC Expanded Selection! Dec. Size LOC MORE ITEMS IN STOCK!.0005 Increments In Stock Through.275 meter &.001 Increments From.2580 to.5050 meter! MO-CR1950 $ MO-CR2235 $ MO-CR2530 $ MO-CR1955 $ MO-CR2240 $ MO-CR2535 $ #9 1 3 MO-CR1960 $ MO-CR2245 $ MO-CR2540 $ MO-CR1965 $ MO-CR2250 $ MO-CR2545 $ mm 1 3 MO-CR1969 $ MO-CR2255 $ MO-CR2550 $ MO-CR1970 $ MO-CR2260 $ mm 1-1/8 3-1/4 MO-CR2559 $ MO-CR1975 $ MO-CR2265 $ /8 3-1/4 MO-CR2560 $ MO-CR1980 $ MO-CR2270 $ /8 3-1/4 MO-CR2565 $ MO-CR1985 $ MO-CR2275 $ F 1-1/8 3-1/4 MO-CR2570 $ #8 1 3 MO-CR1990 $ #1 1 3 MO-CR2280 $ /8 3-1/4 MO-CR2575 $ MO-CR1995 $ MO-CR2285 $ /8 3-1/4 MO-CR2580 $ MO-CR2000 $ MO-CR2290 $ /8 3-1/4 MO-CR2590 $ MO-CR2005 $ MO-CR2295 $ /8 3-1/4 MO-CR2600 $ #7 1 3 MO-CR2010 $ MO-CR2300 $ G 1-1/8 3-1/4 MO-CR2610 $ MO-CR2015 $ MO-CR2305 $ /8 3-1/4 MO-CR2620 $ MO-CR2020 $ MO-CR2310 $ /8 3-1/4 MO-CR2630 $ MO-CR2025 $ MO-CR2315 $ /8 3-1/4 MO-CR2635 $ MO-CR2030 $ MO-CR2320 $ /8 3-1/4 MO-CR2640 $ / MO-CR2031 $ MO-CR2325 $ /8 3-1/4 MO-CR2650 $ MO-CR2035 $ MO-CR2330 $ /64 1-1/8 3-1/4 MO-CR2656 $ #6 1 3 MO-CR2040 $ MO-CR2335 $ H 1-1/8 3-1/4 MO-CR2660 $ MO-CR2045 $ A 1 3 MO-CR2340 $ /8 3-1/4 MO-CR2670 $ MO-CR2050 $ / MO-CR2344 $ /8 3-1/4 MO-CR2680 $ #5 1 3 MO-CR2055 $ MO-CR2345 $ /8 3-1/4 MO-CR2690 $ MO-CR2060 $ MO-CR2350 $ /8 3-1/4 MO-CR2700 $ MO-CR2065 $ MO-CR2355 $ /8 3-1/4 MO-CR2710 $ MO-CR2070 $ MO-CR2360 $ I 1-1/8 3-1/4 MO-CR2720 $ MO-CR2075 $ mm 1 3 MO-CR2362 $ /8 3-1/4 MO-CR2730 $ MO-CR2080 $ MO-CR2365 $ /8 3-1/4 MO-CR2740 $ MO-CR2085 $ MO-CR2370 $ /8 3-1/4 MO-CR2750 $ #4 1 3 MO-CR2090 $ MO-CR2375 $ mm 1-1/8 3-1/4 MO-CR2756 $ MO-CR2095 $ MO-CR2380 $ /8 3-1/4 MO-CR2760 $ MO-CR2100 $ MO-CR2385 $ J 1-1/8 3-1/4 MO-CR2770 $ MO-CR2105 $ MO-CR2390 $ /8 3-1/4 MO-CR2780 $ MO-CR2110 $ MO-CR2395 $ /8 3-1/4 MO-CR2790 $ MO-CR2115 $ MO-CR2400 $ /8 3-1/4 MO-CR2800 $ MO-CR2120 $ MO-CR2405 $ K 1-1/8 3-1/4 MO-CR2810 $ MO-CR2125 $ MO-CR2410 $ /32 1-1/8 3-1/4 MO-CR2812 $ #3 1 3 MO-CR2130 $ MO-CR2415 $ /8 3-1/4 MO-CR2818 $ MO-CR2135 $ C 1 3 MO-CR2420 $ /8 3-1/4 MO-CR2820 $ MO-CR2140 $ MO-CR2425 $ /8 3-1/4 MO-CR2830 $ MO-CR2145 $ MO-CR2430 $ /8 3-1/4 MO-CR2840 $ MO-CR2150 $ MO-CR2435 $ /8 3-1/4 MO-CR2850 $ MO-CR2155 $ MO-CR2440 $ /8 3-1/4 MO-CR2860 $ MO-CR2160 $ MO-CR2445 $ /8 3-1/4 MO-CR2870 $ mm 1 3 MO-CR2165 $ MO-CR2450 $ /8 3-1/4 MO-CR2880 $ MO-CR2170 $ MO-CR2455 $ /8 3-1/4 MO-CR2890 $ MO-CR2175 $ D 1 3 MO-CR2460 $ L 1-1/8 3-1/4 MO-CR2900 $ MO-CR2177 $ MO-CR2465 $ /8 3-1/4 MO-CR2910 $ MO-CR2180 $ MO-CR2470 $ /8 3-1/4 MO-CR2920 $ MO-CR2185 $ MO-CR2475 $ /8 3-1/4 MO-CR2930 $ / MO-CR2188 $ D/P 1 3 MO-CR2480 $ /8 3-1/4 MO-CR2940 $ MO-CR2190 $ MO-CR2485 $ M 1-1/8 3-1/4 MO-CR2950 $ MO-CR2195 $ U/S 1 3 MO-CR2490 $ mm 1-1/8 3-1/4 MO-CR2953 $ MO-CR2200 $ D/P 1 3 MO-CR2495 $ /8 3-1/4 MO-CR2960 $ MO-CR2205 $ /4 1 3 MO-CR2500 $ /64 1-1/8 3-1/4 MO-CR2964 $ #2 1 3 MO-CR2210 $ MO-CR2505 $ /8 3-1/4 MO-CR2970 $ MO-CR2215 $ O/S 1 3 MO-CR2510 $ /8 3-1/4 MO-CR2980 $ MO-CR2220 $ MO-CR2515 $ /8 3-1/4 MO-CR2990 $ MO-CR2225 $ MO-CR2520 $ /8 3-1/4 MO-CR3000 $ MO-CR2230 $ MO-CR2525 $ /8 3-1/4 MO-CR3010 $67.35 D

201 SOLID CARIDE CHUCKING REAMERS SOLID CARIDE CHUCKING REAMERS (continued) Straight -Straight Flute C2 Micrograin Carbide Dec. Size LOC Dec. Size LOC Expanded Selection! Dec. Size LOC MORE ITEMS IN STOCK!.0005 Increments In Stock Through.275 meter &.001 Increments From.2580 to.5050 meter! N 1-1/8 3-1/4 MO-CR3020 $ /4 3-1/2 MO-CR3550 $ /4 3-1/2 MO-CR4090 $ /8 3-1/4 MO-CR3030 $ /4 3-1/2 MO-CR3560 $ /4 3-1/2 MO-CR4100 $ /8 3-1/4 MO-CR3040 $ /4 3-1/2 MO-CR3570 $ /4 3-1/2 MO-CR4110 $ /8 3-1/4 MO-CR3050 $ T 1-1/4 3-1/2 MO-CR3580 $ /4 3-1/2 MO-CR4120 $ /8 3-1/4 MO-CR3060 $ /4 3-1/2 MO-CR3590 $ Z 1-1/4 3-1/2 MO-CR4130 $ /8 3-1/4 MO-CR3070 $ /64 1-1/4 3-1/2 MO-CR3594 $ mm 1-1/4 3-1/2 MO-CR4134 $ /8 3-1/4 MO-CR3080 $ /4 3-1/2 MO-CR3600 $ /4 3-1/2 MO-CR4140 $ /8 3-1/4 MO-CR3090 $ /4 3-1/2 MO-CR3610 $ /4 3-1/2 MO-CR4150 $ /8 3-1/4 MO-CR3100 $ /4 3-1/2 MO-CR3620 $ /4 3-1/2 MO-CR4160 $ D/P 1-1/8 3-1/4 MO-CR3105 $ /4 3-1/2 MO-CR3630 $ /8 4 MO-CR4170 $ /8 3-1/4 MO-CR3110 $ /4 3-1/2 MO-CR3640 $ /8 4 MO-CR4180 $ U/S 1-1/8 3-1/4 MO-CR3115 $ /4 3-1/2 MO-CR3650 $ /8 4 MO-CR4190 $ D/P 1-1/8 3-1/4 MO-CR3120 $ /4 3-1/2 MO-CR3660 $ /8 4 MO-CR4200 $ /16 1-1/8 3-1/4 MO-CR3125 $ /4 3-1/2 MO-CR3670 $ /8 4 MO-CR4210 $ /8 3-1/4 MO-CR3130 $ U 1-1/4 3-1/2 MO-CR3680 $ /64 1-3/8 4 MO-CR4219 $ O/S 1-1/8 3-1/4 MO-CR3135 $ /4 3-1/2 MO-CR3690 $ /8 4 MO-CR4230 $ /8 3-1/4 MO-CR3140 $ /4 3-1/2 MO-CR3700 $ /8 4 MO-CR4240 $ mm 1-1/8 3-1/4 MO-CR3150 $ /4 3-1/2 MO-CR3710 $ /8 4 MO-CR4250 $ O 1-1/8 3-1/4 MO-CR3160 $ /4 3-1/2 MO-CR3720 $ /8 4 MO-CR4260 $ /4 3-1/2 MO-CR3170 $ D/P 1-1/4 3-1/2 MO-CR3730 $ /8 4 MO-CR4270 $ /4 3-1/2 MO-CR3180 $ mm 1-1/4 3-1/2 MO-CR3740 $ /8 4 MO-CR4280 $ /4 3-1/2 MO-CR3190 $ D/P 1-1/4 3-1/2 MO-CR3745 $ /8 4 MO-CR4290 $ /4 3-1/2 MO-CR3200 $ /8 1-1/4 3-1/2 MO-CR3750 $ /8 4 MO-CR4300 $ /4 3-1/2 MO-CR3210 $ /4 3-1/2 MO-CR3755 $ /8 4 MO-CR4310 $ /4 3-1/2 MO-CR3220 $ O/S 1-1/4 3-1/2 MO-CR3760 $ /8 4 MO-CR4320 $ P 1-1/4 3-1/2 MO-CR3230 $ /4 3-1/2 MO-CR3765 $ /8 4 MO-CR4330 $ /4 3-1/2 MO-CR3240 $ V 1-1/4 3-1/2 MO-CR3770 $ mm 1-3/8 4 MO-CR4331 $ /4 3-1/2 MO-CR3250 $ /4 3-1/2 MO-CR3780 $ /8 4 MO-CR4340 $ /4 3-1/2 MO-CR3260 $ /4 3-1/2 MO-CR3790 $ /8 4 MO-CR4350 $ /4 3-1/2 MO-CR3270 $ /4 3-1/2 MO-CR3800 $ D/P 1-3/8 4 MO-CR4355 $ /4 3-1/2 MO-CR3280 $ /4 3-1/2 MO-CR3810 $ /8 4 MO-CR4360 $ /64 1-1/4 3-1/2 MO-CR3281 $ /4 3-1/2 MO-CR3820 $ U/S 1-3/8 4 MO-CR4365 $ /4 3-1/2 MO-CR3290 $ /4 3-1/2 MO-CR3830 $ D/P 1-3/8 4 MO-CR4370 $ /4 3-1/2 MO-CR3300 $ /4 3-1/2 MO-CR3840 $ /16 1-3/8 4 MO-CR4375 $ /4 3-1/2 MO-CR3310 $ /4 3-1/2 MO-CR3850 $ /8 4 MO-CR4380 $ Q 1-1/4 3-1/2 MO-CR3320 $ W 1-1/4 3-1/2 MO-CR3860 $ O/S 1-3/8 4 MO-CR4385 $ /4 3-1/2 MO-CR3330 $ /4 3-1/2 MO-CR3870 $ /8 4 MO-CR4390 $ /4 3-1/2 MO-CR3340 $ /4 3-1/2 MO-CR3880 $ /8 4 MO-CR4400 $ mm 1-1/4 3-1/2 MO-CR3346 $ /4 3-1/2 MO-CR3890 $ /8 4 MO-CR4410 $ /4 3-1/2 MO-CR3350 $ /4 3-1/2 MO-CR3900 $ /8 4 MO-CR4420 $ /4 3-1/2 MO-CR3360 $ /64 1-1/4 3-1/2 MO-CR3906 $ /8 4 MO-CR4430 $ /4 3-1/2 MO-CR3370 $ /4 3-1/2 MO-CR3910 $ /8 4 MO-CR4440 $ /4 3-1/2 MO-CR3380 $ /4 3-1/2 MO-CR3920 $ /8 4 MO-CR4450 $ R 1-1/4 3-1/2 MO-CR3390 $ /4 3-1/2 MO-CR3930 $ /8 4 MO-CR4460 $ /4 3-1/2 MO-CR3400 $ mm 1-1/4 3-1/2 MO-CR3937 $ /8 4 MO-CR4470 $ /4 3-1/2 MO-CR3410 $ /4 3-1/2 MO-CR3940 $ /8 4 MO-CR4480 $ /4 3-1/2 MO-CR3420 $ /4 3-1/2 MO-CR3950 $ /8 4 MO-CR4490 $ /4 3-1/2 MO-CR3430 $ /4 3-1/2 MO-CR3960 $ /8 4 MO-CR4500 $ /32 1-1/4 3-1/2 MO-CR3438 $ X 1-1/4 3-1/2 MO-CR3970 $ /8 4 MO-CR4510 $ /4 3-1/2 MO-CR3440 $ /4 3-1/2 MO-CR3980 $ /8 4 MO-CR4520 $ /4 3-1/2 MO-CR3450 $ /4 3-1/2 MO-CR3990 $ mm 1-3/8 4 MO-CR4528 $ /4 3-1/2 MO-CR3460 $ /4 3-1/2 MO-CR4000 $ /8 4 MO-CR4530 $ /4 3-1/2 MO-CR3470 $ /4 3-1/2 MO-CR4010 $ /64 1-3/8 4 MO-CR4531 $ S 1-1/4 3-1/2 MO-CR3480 $ /4 3-1/2 MO-CR4020 $ /8 4 MO-CR4540 $ /4 3-1/2 MO-CR3490 $ /4 3-1/2 MO-CR4030 $ /8 4 MO-CR4550 $ /4 3-1/2 MO-CR3500 $ Y 1-1/4 3-1/2 MO-CR4040 $ /8 4 MO-CR4560 $ /4 3-1/2 MO-CR3510 $ /4 3-1/2 MO-CR4050 $ /8 4 MO-CR4570 $ /4 3-1/2 MO-CR3520 $ /4 3-1/2 MO-CR4060 $ /8 4 MO-CR4580 $ /4 3-1/2 MO-CR3530 $ /32 1-1/4 3-1/2 MO-CR4062 $ /8 4 MO-CR4590 $ /4 3-1/2 MO-CR3540 $ /4 3-1/2 MO-CR4070 $ /8 4 MO-CR4600 $ mm 1-1/4 3-1/2 MO-CR3543 $ /4 3-1/2 MO-CR4080 $ /8 4 MO-CR4610 $ Master Catalog 469 D CARIDE INSERTS DEURRING

202 CHUCK JAWS LATHE WORKHOLDING SOLID CARIDE REAMERS/MICRO REAMERS SOLID CARIDE CHUCKING REAMERS (continued) Straight -Straight Flute C2 Micrograin Carbide MORE ITEMS IN STOCK!.0005 Increments In Stock Through.275 meter &.001 Increments From.2580 to.5050 meter! D MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Dec. Size LOC Master Catalog Dec. Size LOC Dec. Size LOC /8 4 MO-CR4620 $ /8 4 MO-CR4780 $ /2 4 MO-CR4940 $ /8 4 MO-CR4630 $ /2 4 MO-CR4790 $ /2 4 MO-CR4950 $ /8 4 MO-CR4640 $ /2 4 MO-CR4800 $ /2 4 MO-CR4960 $ /8 4 MO-CR4650 $ /2 4 MO-CR4805 $ /2 4 MO-CR4970 $ /8 4 MO-CR4660 $ /2 4 MO-CR4810 $ D/P 1-1/2 4 MO-CR4980 $ /8 4 MO-CR4670 $ /2 4 MO-CR4820 $ U/S 1-1/2 4 MO-CR4990 $ /8 4 MO-CR4680 $ /2 4 MO-CR4830 $ D/P 1-1/2 4 MO-CR4995 $ /32 1-3/8 4 MO-CR4688 $ /2 4 MO-CR4840 $ /2 1-1/2 4 MO-CR5000 $ /8 4 MO-CR4690 $ /64 1-1/2 4 MO-CR4844 $ /2 4 MO-CR5005 $ /8 4 MO-CR4700 $ /2 4 MO-CR4850 $ O/S 1-1/2 4 MO-CR5010 $ /8 4 MO-CR4710 $ /2 4 MO-CR4860 $ /2 4 MO-CR5015 $ /8 4 MO-CR4720 $ /2 4 MO-CR4870 $ /2 4 MO-CR5020 $ mm 1-3/8 4 MO-CR4724 $ /2 4 MO-CR4880 $ /2 4 MO-CR5030 $ /8 4 MO-CR4730 $ /2 4 MO-CR4890 $ /2 4 MO-CR5040 $ /8 4 MO-CR4740 $ /2 4 MO-CR4900 $ /2 4 MO-CR5050 $ /8 4 MO-CR4750 $ /2 4 MO-CR4910 $ /8 4 MO-CR4760 $ mm 1-1/2 4 MO-CR4921 $ /8 4 MO-CR4770 $ /2 4 MO-CR4930 $ SOLID CARIDE HIGH PRECISION MICRO REAMERS Spiral Flute-Right Hand Cut-Left Hand Helix For through hole applications Tolerance to = 4 flutes to = 6 flutes 10 left spiral, right hand cut Special orders also available mm Dec. mm Dec. mm Dec MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $22.90 (Continued On Following Page)

203 SOLID CARIDE MICRO REAMERS SOLID CARIDE HIGH PRECISION MICRO REAMERS (continued) Spiral Flute-Right Hand Cut-Left Hand Helix mm Dec. For through hole applications Tolerance to = 4 flutes to = 6 flutes 10 left spiral, right hand cut Special orders also available mm Dec. mm Dec MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ MAG $ Master Catalog 471 C CARIDE INSERTS DEURRING

204 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD CHUCKING REAMERS-HSS CHUCKING REAMERS High Speed Steel List No Straight Flute, Straight, Right Hand Cut List No Right Hand Spiral Flutes, Straight, Right Hand Cut Dec. Equiv Flute Len. No. of Flutes List 433 List 435 # /8 2 3/4 YA $ # /8 2 3/4 YA $ / /8 2 3/4 YA $ # /8 2 7/8 YA $ # /8 2 7/8 YA $ # /8 2 7/8 YA $ # /2 3 1 YA $ # /2 3 1 YA $ # / /8 YA $ # / /8 YA $ # / /4 YA $ # / /4 YA $ # / /8 YA $ # / /8 YA $ / / /8 YA $ # / /8 YA $ # / /8 YA $ # / /2 YA $ # / /2 YA $ # / /2 YA $ # / /2 YA $ # / /2 YA $ / /2 YA $12.02 YA $13.83 # / /2 YA $12.02 YA $13.83 # / /2 YA $12.02 YA $13.83 # / /2 YA $12.02 YA $13.83 # / /2 YA $12.02 YA $13.83 # / /2 YA $12.02 YA $ / / /2 YA $12.02 YA $13.83 # / /2 YA $12.02 YA $13.83 # / /2 YA $12.02 YA $ / /2 YA $12.02 YA $13.83 # / /2 YA $12.02 YA $ / / /2 YA $10.82 YA $13.83 # / /2 YA $10.82 YA $13.83 # /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $ / /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $ /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $11.14 # /4 4 3 YA $9.67 YA $ / /4 4 3 YA $8.71 YA $11.04 # / /2 YA $9.78 YA $11.24 # / /2 YA $9.78 YA $ / /2 YA $9.78 YA $11.24 # / /2 YA $9.78 YA $11.24 # / /2 YA $9.78 YA $11.24 # / /2 YA $9.78 YA $11.24 # / /2 YA $9.78 YA $ / / /2 YA $10.07 YA $11.56 # / /2 YA $10.07 YA $11.56 # / /2 YA $10.07 YA $11.56 # / /2 YA $10.07 YA $11.56 # / /2 YA $10.07 YA $ Master Catalog Dec. Equiv Flute Len. No. of Flutes List 433 List 435 List 433 List 435 3mm / /2 YA $10.07 YA $11.56 # / /2 YA $10.07 YA $11.56 O/U / /2 YA $10.07 YA $ / / /2 YA $8.04 YA $10.42 O/U / /2 YA $10.07 YA $11.56 # / /2 YA $10.07 YA $11.56 # YA $12.02 YA $ mm YA $15.19 YA $13.83 # YA $12.02 YA $ / YA $12.02 YA $13.83 # YA $12.02 YA $13.83 # YA $12.02 YA $13.83 # YA $12.02 YA $13.83 # YA $15.19 YA $13.83 # YA $12.02 YA $ / YA $12.02 YA $13.83 # YA $12.02 YA $ mm YA $12.02 YA $13.83 # / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $ / / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $ mm / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $14.77 O/U / /2 YA $12.85 YA $ / / /2 YA $11.56 YA $14.03 O/U / /2 YA $12.85 YA $14.77 # / /2 YA $12.85 YA $14.77 # /4 6 5 YA $14.41 YA $16.54 # /4 6 5 YA $14.41 YA $16.54 # /4 6 5 YA $14.41 YA $ mm /4 6 5 YA $14.41 YA $16.54 # /4 6 5 YA $14.41 YA $16.54 # /4 6 5 YA $14.41 YA $ / /4 6 5 YA $14.41 YA $16.54 # /4 6 5 YA $14.41 YA $16.54 # /4 6 5 YA $14.41 YA $16.54 # /4 6 5 YA $14.41 YA $16.54 # /4 6 5 YA $14.41 YA $ mm /4 6 5 YA $14.41 YA $ / /4 6 5 YA $14.41 YA $16.54 # /2 6 6 YA $14.78 YA $17.00 # /2 6 6 YA $14.78 YA $17.00 A /2 6 6 YA $14.78 YA $ / /2 6 6 YA $14.78 YA $ mm /2 6 6 YA $15.58 YA $ /2 6 6 YA $15.58 YA $17.11 C /2 6 6 YA $15.58 YA $17.11 D /2 6 6 YA $15.58 YA $17.11 O/U /2 6 6 YA $14.03 YA $18.27 E /2 6 6 YA $13.25 YA $14.57 O/U /2 6 6 YA $14.03 YA $ mm /2 6 6 YA $15.58 YA $17.11 F /2 6 6 YA $15.58 YA $17.11 G /2 6 6 YA $15.58 YA $17.11 (continued on following page)

205 CHUCKING REAMERS-HSS CHUCKING REAMERS (continued) High Speed Steel List No Straight Flute, Straight, Right Hand Cut List No Right Hand Spiral Flutes, Straight, Right Hand Cut Dec. Equiv Flute Length No. of Flutes List 433 List 435 List 433 List / /2 6 6 YA $17.37 YA $19.11 H /2 6 6 YA $17.37 YA $19.11 I /2 6 6 YA $17.37 YA $ mm /2 6 6 YA $17.37 YA $19.11 J /2 6 6 YA $17.37 YA $19.11 K /2 6 6 YA $23.23 YA $ / /2 6 6 YA $16.50 YA $17.91 L /2 6 6 YA $17.37 YA $19.11 M /2 6 6 YA $17.37 YA $ mm /2 6 6 YA $17.37 YA $ / /2 6 6 YA $17.37 YA $19.11 N /2 6 6 YA $17.37 YA $19.11 O/U /2 6 6 YA $16.50 YA $ / /2 6 6 YA $15.65 YA $17.20 O/U /2 6 6 YA $16.50 YA $ mm /2 6 6 YA $17.37 YA $19.11 O /2 6 6 YA $17.37 YA $19.11 P /2 6 6 YA $18.57 YA $ / /2 6 6 YA $18.57 YA $20.44 Q /2 6 6 YA $18.57 YA $ mm /2 6 6 YA $18.57 YA $20.44 R /2 6 6 YA $18.57 YA $ / /2 6 6 YA $18.57 YA $20.44 S /4 6 7 YA $18.75 YA $ mm /4 6 7 YA $18.75 YA $20.62 T /4 6 7 YA $18.75 YA $ / /4 6 7 YA $18.75 YA $20.62 U /4 6 7 YA $18.75 YA $20.62 O/U /4 6 7 YA $17.81 YA $ / /4 6 7 YA $16.85 YA $18.56 O/U /4 6 7 YA $17.81 YA $19.58 V /4 6 7 YA $20.38 YA $22.44 W /4 6 7 YA $20.38 YA $ / /4 6 7 YA $20.38 YA $ mm /4 6 7 YA $20.38 YA $22.44 X /4 6 7 YA $20.38 YA $22.44 Y /4 6 7 YA $21.16 YA $ / /4 6 7 YA $21.16 YA $23.28 Z /4 6 7 YA $21.16 YA $ mm /4 6 7 YA $21.16 YA $ / /4 6 7 YA $21.16 YA $ mm /4 6 7 YA $21.16 YA $23.28 O/U /4 6 7 YA $20.09 YA $ / /4 6 7 YA $20.09 YA $22.10 O/U /4 6 7 YA $20.09 YA $ mm /4 6 7 YA $23.03 YA $ / /4 6 7 YA $23.03 YA $ / /4 6 7 YA $23.03 YA $ mm YA $23.03 YA $ / YA $23.03 YA $ mm YA $23.03 YA $25.35 O/U YA $21.86 YA $ / YA $21.86 YA $24.07 O/U YA $21.86 YA $ mm YA $ / YA $ / YA $27.20 YA $ mm YA $ / YA $ mm YA $ O/U YA $ Dec. Equiv Flute Length No. of Flutes List Master Catalog 473 9/ YA $27.20 O/U YA $ mm YA $ / YA $ mm YA $ / YA $ / /4 8 9 YA $ mm /4 8 9 YA $33.32 #N/A /4 8 9 YA $ / /4 8 9 YA $31.84 #N/A /4 8 9 YA $ mm /4 8 9 YA $ / /4 8 9 YA $ mm /4 8 9 YA $ / /4 8 9 YA $ mm /4 8 9 YA $ / /4 8 9 YA $37.65 O/U /4 8 9 YA $ / /4 8 9 YA $35.87 O/U /4 8 9 YA $ mm /4 8 9 YA $ / /4 8 9 YA $ mm /4 8 9 YA $ / /4 8 9 YA $ mm / /2 YA $ / / /2 YA $ mm / /2 YA $46.54 O/U / /2 YA $ / / /2 YA $40.27 O/U / /2 YA $ / / /2 YA $ mm / /2 YA $ / / /2 YA $ mm / /2 YA $ / / /2 YA $ mm / /2 YA $47.96 O/U / /2 YA $ / / /2 YA $43.44 O/U / /2 YA $ mm / /2 YA $ / / /2 YA $ / / /2 YA $ mm / YA $ / / YA $ mm / YA $55.91 O/U / YA $ / / YA $52.56 O/U / YA $ mm / YA $ / / YA $ mm / YA $ / / YA $ / / YA $ mm / YA $61.17 O/U / YA $ / / YA $56.64 O/U / YA $ mm / YA $ / / YA $ mm / YA $ / / YA $63.45 CARIDE INSERTS DEURRING

206 CHUCK JAWS LATHE WORKHOLDING CHUCKING REAMERS-COALT CHUCKING REAMERS M-42 Cobalt List No Straight, Straight Flute, Right Hand Cut List No RH Spiral Flutes, Straight, Right Hand Cut also available MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Dec. Equiv Flute Length No. of Flutes List 1433 # /8 2 3/4 YA $15.90 # /8 2 3/4 YA $ / /8 2 3/4 YA $15.90 # /8 2 7/8 YA $15.90 # /8 2 7/8 YA $15.90 # /8 2 7/8 YA $15.90 # /2 3 1 YA $15.90 # /2 3 1 YA $15.90 # / /8 YA $15.90 # / /8 YA $15.90 # / /4 YA $15.90 # / /4 YA $15.90 # / /8 YA $15.90 # / /8 YA $ / / /8 YA $13.09 # / /8 YA $13.09 # / /8 YA $13.09 # / /2 YA $13.09 # / /2 YA $13.09 # / /2 YA $13.09 # / /2 YA $13.09 # / /2 YA $13.09 O/U / /2 YA $12.89 # / /2 YA $12.89 # / /2 YA $12.89 # / /2 YA $12.89 # / /2 YA $12.89 # / /2 YA $ / / /2 YA $12.89 # / /2 YA $12.89 # / /2 YA $12.89 O/U / /2 YA $12.89 # / /2 YA $ / / /2 YA $12.89 # / /2 YA $12.89 # /4 4 3 YA $10.37 # /4 4 3 YA $10.37 # /4 4 3 YA $10.37 # /4 4 3 YA $ / /4 4 3 YA $10.37 # /4 4 3 YA $10.37 O/U /4 4 3 YA $10.37 # /4 4 3 YA $10.37 # /4 4 3 YA $10.37 # /4 4 3 YA $10.37 # /4 4 3 YA $10.37 # /4 4 3 YA $ / /4 4 3 YA $10.37 # / /2 YA $10.45 # / /2 YA $10.45 O/U / /2 YA $10.45 # / /2 YA $10.45 # / /2 YA $10.45 # / /2 YA $10.45 # / /2 YA $ / / /2 YA $10.78 # / /2 YA $10.78 # / /2 YA $10.78 # / /2 YA $10.78 # / /2 YA $ Master Catalog Dec. Equiv Flute Length No. of Flutes List 1433 O/U / /2 YA $10.78 # / /2 YA $10.78 O/U / /2 YA $ / / /2 YA $8.61 O/U / /2 YA $10.78 # / /2 YA $10.78 # YA $12.87 O/U YA $12.87 # YA $ / YA $12.87 # YA $12.87 # YA $12.87 # YA $12.87 # YA $12.87 # YA $ / YA $11.56 # YA $12.87 O/U YA $12.87 # / /2 YA $13.75 # / /2 YA $13.75 # / /2 YA $13.75 # / /2 YA $ / / /2 YA $13.75 # / /2 YA $13.75 # / /2 YA $13.75 O/U / /2 YA $13.75 # / /2 YA $13.75 # / /2 YA $13.75 # / /2 YA $13.75 O/U / /2 YA $ / / /2 YA $12.37 O/U / /2 YA $13.75 # / /2 YA $13.75 # /4 6 5 YA $16.62 # /4 6 5 YA $16.62 # /4 6 5 YA $16.62 O/U /4 6 5 YA $16.62 # /4 6 5 YA $16.62 # /4 6 5 YA $ / /4 6 5 YA $16.62 # /4 6 5 YA $16.62 # /4 6 5 YA $16.62 # /4 6 5 YA $16.62 # /4 6 5 YA $16.62 O/U /4 6 5 YA $ / /4 6 5 YA $16.62 # /2 6 6 YA $17.09 # /2 6 6 YA $17.09 A /2 6 6 YA $ / /2 6 6 YA $17.09 O/U /2 6 6 YA $ /2 6 6 YA $17.17 C /2 6 6 YA $17.17 D /2 6 6 YA $15.61 O/U /2 6 6 YA $15.44 E /2 6 6 YA $21.70 O/U /2 6 6 YA $15.44 O/U /2 6 6 YA $17.17 F /2 6 6 YA $17.17 G /2 6 6 YA $17.17 (continued on following page)

207 CHUCKING REAMERS-COALT CHUCKING REAMERS M-42 Cobalt List No Straight, Straight Flute, Right Hand Cut List No RH Spiral Flutes, Straight, Right Hand Cut also available Dec. Equiv Flute Length No. of Flutes List / /2 6 6 YA $23.28 H /2 6 6 YA $23.28 I /2 6 6 YA $23.28 O/U /2 6 6 YA $23.28 J /2 6 6 YA $23.28 K /2 6 6 YA $ / /2 6 6 YA $22.11 L /2 6 6 YA $23.28 M /2 6 6 YA $23.28 O/U /2 6 6 YA $ / /2 6 6 YA $23.28 N /2 6 6 YA $23.28 O/U /2 6 6 YA $ / /2 6 6 YA $20.94 O/U /2 6 6 YA $22.11 O/U /2 6 6 YA $33.02 O /2 6 6 YA $23.28 P /2 6 6 YA $ / /2 6 6 YA $25.08 Q /2 6 6 YA $25.08 O/U /2 6 6 YA $25.08 R /2 6 6 YA $ / /2 6 6 YA $25.08 S /4 6 7 YA $25.51 O/U /4 6 7 YA $25.51 T /4 6 7 YA $ / /4 6 7 YA $25.51 U /4 6 7 YA $25.51 O/U /4 6 7 YA $ / /4 6 7 YA $22.95 O/U /4 6 7 YA $24.20 V /4 6 7 YA $44.10 W /4 6 7 YA $ / /4 6 7 YA $31.08 O/U /4 6 7 YA $31.08 DOWEL PIN REAMERS High Speed Steel & M-42 Cobalt List No High Speed Steel, Straight Flute List No M-42 Cobalt, Straight Flute What s the difference between Dowel Pin Reamers and Standard Chucking Reamers? Standard chucking reamers are produced with little back taper and a plus diameter tolerance, while dowel pin reamers are produced with increased back taper and a minus diameter tolerance. COMPLETE LINE AVAILALE! Hand Reamers Taper Reamers Stub Screw Expansion Reamers Counterbores Sets Flute Length No. of Flutes Dec. Equiv Flute Length No. of Flutes List Master Catalog 475 X /4 6 7 YA $31.08 Y /4 6 7 YA $ / /4 6 7 YA $31.08 Z /4 6 7 YA $31.08 O/U /4 6 7 YA $ / /4 6 7 YA $31.08 O/U /4 6 7 YA $31.08 O/U /4 6 7 YA $ / /4 6 7 YA $29.53 O/U /4 6 7 YA $31.08 O/U /4 6 7 YA $ / /4 6 7 YA $ / /4 6 7 YA $35.63 O/U YA $ / YA $35.63 O/U YA $35.63 O/U YA $ / YA $33.84 O/U YA $ / YA $ / YA $ / YA $ / /4 8 9 YA $ / /4 8 9 YA $ / /4 8 9 YA $ / /4 8 9 YA $ / / /2 YA $ / / /2 YA $ / / /2 YA $ / / /2 YA $ / / YA $ / / YA $ / / YA $ / / YA $ / / YA $98.21 List 470 List / /2 YA $10.07 YA $ / /2 YA $10.07 YA $ / /2 YA $12.85 YA $ / /2 YA $12.85 YA $ /2 6 6 YA $14.03 YA $ /2 6 6 YA $14.03 YA $ /2 6 6 YA $16.50 YA $ /2 6 6 YA $16.50 YA $ /4 6 7 YA $17.79 YA $ /4 6 7 YA $17.79 YA $ /4 6 7 YA $20.09 YA $ /4 6 7 YA $20.09 YA $ YA $21.86 YA $ YA $21.86 YA $33.95 CARIDE INSERTS DEURRING

208 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD KNURLING TOOLS CNC MODULAR KNURLING TOOL SHANK Specifically designed for the CNC Lathe. Precision square shank with preset center height. Right or Left hand applications. One shank fits all heads. One head fits all shanks. Cobalt knurl wheels, Tin-c coated. Carbide knurl pin. Easy set-up. Center height adjustment. Interchangeable knurl heads. High productivity. est knurl quality. Long knurl wheel life. Low production cost. CNC MODULAR KNURLING TOOL HEADS Type 1 Small meter mond Cutting Knurling Head Cutting Style Small meter Range mond Pattern Only End Feed Feed Range:.004 to.012 Type 2 Heavy Duty mond Cutting Knurling Head Cutting Style Medium meter Range mond Pattern Only End Feed Feed Range:.004 to.016 Type 3 Extra Heavy Duty mond Cutting Knurling Head Cutting Style Large meter Range mond Pattern Only End Feed Feed Range:.004 to.025 Type 5 Single Wheel Forming Knurling Head Forming Style Unrestricted. Range Straight Pattern Male mond Pattern Female mond Pattern In Feed and End Feed Style 6 Shoulder Forming Knurling Head Forming Style 5/16 & Up. Range Shoulder Knurling Straight Pattern Male mond Pattern In Feed and End Feed Style 7 Straddle Forming Knurling Head Forming Style Up to 1. Range Straddle Knurling Straight Pattern Male mond Pattern In Feed and End Feed Left Hand Description Master Catalog Knurl Wheel. Range Knurl Pin Desc. SCNCKH-1-2 DN20335 $ SW2S PSW-2.0S DN29005 $43.16 CNCKH-1-2 DN21035 $ SW2S PSW-2.0S DN29005 $43.16 Description Knurl Wheel. Range Knurl Pin Desc. CNCKH-2-R DN21040 $ R KPS C DN28925 $29.58 Description Knurl Wheel. Range Knurl Pin Desc. CNCKH-3-M DN21045 $ M 2.0-up KPS C DN28945 $30.89 Description Knurl Wheel. Range Knurl Pin Desc. CNCKH-5-O DN21050 $ O N/A KPS C DN28950 $32.64 Description Knurl Wheel. Range Knurl Pin Desc. SCNCKH-6-2 DN20340 $ SW2.312 &up SW2.0P-2S DN29055 $43.16 CNCKH-6-4 DN21056 $ SW4.312 &up SW4.0P-2S DN29085 $50.60 Description Size Width Knurl Wheel Length. Range Right Hand Description Knurl Pin Desc SCNC-37 DN20310 $ SCNC-50 DN20320 $ SCNC-162 DN20325 $ CNC-75 DN21010 $ CNC-100 DN21020 $ CNC-125 DN21030 $ SCNCKH-7-D DN20345 $ D 0.5 KPS C DN28905 $23.65 CNCKH-7-R DN21060 $ R 1 KPS C DN28915 $25.41

209 KNURLING TOOLS Modular Versatility The CNC Modular Knurling Tool is a tooling system which combines exceptional versatility, rigidity, ease of handling, and simplicity. Knurl wheels, heads, and shanks can be combined to build your own knurling tool to fit any work application and machine. Precision square shank with preset center height. Right or Left hand applications. CUTTING CNC Small cutting range: 5/16" to 1-1/2" Minimum stress on the machine, and faster knurl forming action. Twin straight SW series knurl wheels for diamond pattern. Allows tool to knurl close to a square shoulder. Supplied with SW2S-30C cobalt knurl wheels-tin-c coated. Adds longer life and better performance to the knurl wheels. CUTTING CNC R Heavy duty cutting range: 1" to 5" Minimum stress on the machine, and faster than knurl forming action. Twin straight R series knurl wheels for diamond pattern. Supplies more rigidity for larger diameters Knurl wheels are mounted between thrust washers. Ensures smooth and even rotation of the knurls. Supplied with RS-25-C cobalt knurl wheels - Tin-c coated. Adds longer life and better performance to the knurl wheels. CUTTING CNC M Extra heavy duty cutting range: 1-1/2" & up Minimum stress on the machine, and faster than knurl forming action. Twin straight M series knurl wheels for diamond pattern. Supplies more rigidity for larger diameters Knurl wheels are mounted between thrust washers. Ensures smooth and even rotation of the knurls. Supplied with MS-25-C cobalt knurl wheels - Tin-c coated. Adds longer life and better performance to the knurl wheels. FORMING CNC Straight bump Great quality of knurl pattern. Single O series knurl wheel for straight or diamond pattern. Narrow knurl applications, up to 3/8" wide Knurl wheel is mounted between thrust washers. Ensures smooth and even rotation of the knurl. Supplied with ODF-25-C cobalt knurl wheel - Tin-c coated. Adds longer life and better performance to the knurl wheel. FORMING CNC Shoulder diameter range: 5/16" & up etter quality of knurl pattern. Twin SW series knurl wheels for straight or diamond pattern. Allows tool to knurl against a square shoulder. A thrust washer is mounted between the knurls and tool head. Ensures smooth and even rotation of the knurls. Supplied with SW2R/L-30C or SW4R/L-25C cobalt knurl wheels - Tin-c coated. Adds longer life and better performance to the knurl wheels. FORMING CNC Small diameter range: up to 1" etter quality of knurl pattern. Compact design. Allows more clearance for the tool head. Twin D or R series knurl wheels for straight or diamond pattern. Supplies more rigidity for compact design. Supplied with DDR/L or RDR/L-30-C cobalt knurl wheel - Tin-c coated. Adds longer life and better performance to the knurl wheel. Self-centering knurling head. Precise alignment to the working part. Precise Adjustable Center Height The dovetail mounting of the shank and head insures that the tool will be rigid and adjustable yet easy to use. y turning the adjustment screw clockwise or counterclockwise the center height of the head can be adjusted. eighth turn of the screw, which is marked on the screw, moves the head.004". After the desired center height has been reached, tightening the lock screw ensures that the head will remain in position while knurling a part. One shank fits all heads. One head fits all shanks. Easy set-up. Method of Knurling Knurl forming action displaces the material creating a perfect knurl pattern while sacrificing speeds and feeds. The force applied through forming is increased in larger diameters making knurling difficult and slow. Knurling cutting action cuts a perfect knurl pattern 10 to 20 times faster than a forming knurl tool becoming applicable for CNC use. It is engineered to knurl any material, including thin wall tubing, with minimum stress to the spindle and compound lathe. Center height adjustment. est knurl quality. Interchangeable knurl heads. Low production cost. High productivity. Cutting - 10 to 20 times faster. Description Size Tool Length SCNC DN20010 $ SCNC DN20020 $ SCNC DN20025 $ CNC DN20410 $ CNC DN20420 $ CNC DN20430 $ Description Size Tool Length CNC-75-2-R DN20510 $ CNC R DN20520 $ CNC R DN20530 $ Description Size Tool Length CNC-75-3-M DN20610 $ CNC M DN20620 $ CNC M DN20630 $ Description Size Tool Length CNC-75-5-O DN20710 $ CNC O DN20720 $ CNC O DN20730 $ Description Size Tool Length SCNC DN20110 $ SCNC DN20120 $ SCNC DN20125 $ Description Size Tool Length SCNC-37-7-D DN20210 $ SCNC-50-7-D DN20220 $ SCNC D DN20225 $ CNC-75-7-R DN20910 $ CNC R 1 7 DN20920 $ CNC R DN20930 $ Master Catalog 477 CARIDE INSERTS DEURRING

210 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS TOOLHOLDERS KNURLING TOOLS 3SHKT - Three Swivel Head Knurling Tool Designed to quickly knurl multiple applications with one tool. Precision square shank with preset center height. Twin knurl wheels for straight and diamond pattern. Knurl wheels are mounted between the thrust washers to ensure a smooth and even rotation of the knurls while knurling is performed. Self-centering knurling head for a precise alignment to the working part. Center Height Size SCK - Self-Centering Knurling Tool for CNC Lathe Specifically designed for CNC lathe. Precision square shank with preset center height. Twin knurl wheels for straight and diamond pattern. Knurl wheels are mounted between the thrust washers to ensure a smooth and even rotation of the knurls while knurling is performed. Self-centering knurling head for a precise alignment to the working part. Desc. SSCK - Shoulder Self-Centering Knurling Tool for CNC Lathe Specifically designed for CNC lathe. Designed to knurl against a square shoulder. Precision square shank with preset center height. Twin knurl wheels for straight and diamond pattern. Knurl wheels are mounted between thrust washers to ensure smooth and even rotation of the knurls while knurling is performed. Supplied with Cobalt TIC/N coated SW series knurl wheels. Self-centering knurling head for a precise alignment to the working part. Knurl Wheel Knurl Pin Set x.750 3SHKT-50-D DN21510 $ DDR/L-20-C x.750 3SHKT-162-D DN21515 $ DDR/L-30-C KPS DN28805 $7.08 DDR/L-40-C x SHKT-75-M DN21530 $ MDR/L-16-C x SHKT-100-M DN21540 $ MDR/L-25-C KPS DN28845 $ x SHKT-125-M DN21550 $ MDR/L-35-C Center Height Size Desc. Knurl Wheel Knurl Pin Set x.750 SCK-50-D DN22110 $ DDR/L-30-C KPS DN28805 $ x 1.25 SCK-75-M DN22120 $ x 1.25 SCK-100-M DN22130 $ MDR/L-25-C KPS DN28840 $ x 1.25 SCK-125-M DN22140 $ INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Center Height Size SWFKT - Single Wheel Fixed Knurling Tool for Manual or CNC Lathes Precision square shank with preset center height. Single knurl wheel for straight and diamond pattern. Knurl wheel is mounted between the thrust washers to ensure smooth and even rotation of the knurl while knurling is performed. est used for straight patterns or bump knurling a diamond pattern Master Catalog Desc. Knurl Wheel Knurl Pin Set x.500 SSCK-38-2 DN22210 $ x.625 SSCK-50-2 DN22220 $ SW2-S/R/L SW2.0P-2S DN29055 $ x.750 SSCK-75-4 DN22240 $ x 1.00 SSCK DN22250 $ SW4-S/R/L SW4.0P-2S DN29085 $ x 1.25 SSCK DN22260 $ Center Height Size Desc. KTW109 - metral Shoulder Knurling Tool with Self-Centering Adjustable Floating Straddle This tool is designed when pressure and deflection are a problem. The knurling heads are able to "float" somewhat and center on the workpiece, compensating for any off-centering. Precise square shank with preset center height. A diametrical adjustment screw regulates the depth of the knurl pattern and diameter size. Center Height Size Max. L2 Description Knurl Wheel Knurl Pin Set x.375 SWFKT-38-D DN21720 $80.90 DS-30-C KPS DN28805 $ x.500 SWFKT-50-D DN21730 $80.90 DS-30-C KPS DN28805 $ x.750 SWFKT-75-M DN21740 $ MS-25-C KPS DN28840 $ x1.00 SWFKT-100-O DN21750 $ OS-25-C KPS DN28845 $ x1.25 SWFKT-125-O DN21760 $ OS-25-C KPS DN28850 $ x KTW DN22810 $ x KTW DN22820 $ x KTW DN22830 $ x KTW DN22840 $ Knurl Wheel Knurl Pin Set SW4R/L-25C SW4.0P-2S DN29085 $38.93 SW4R/L-25C SW4.0P-2S DN29085 $38.93

211 KNURLING WHEELS CIRCULAR PITCH KNURLS Made to extremely high standards from the finest materials available. Knurls are individually hob cut and lapped to a smooth hard finish to give longer life and impart a smooth clean surface to the knurled part. Knurls available in High Speed, Cobalt, TIC/N - Coated, beveled, and diametral pitch. A Series High Speed Steel D Series Cobalt Straight gonal Left gonal Right PATTERN TPI Incl. Tooth gonal gonal Straight Angle Right Left DN23502 DN23634 DN DN23504 DN23636 DN DN23506 DN23638 DN DN23508 DN23640 DN DN23510 DN23642 DN DN23512 DN23644 DN DN23514 DN23646 DN DN23516 DN23648 DN DN23518 DN23650 DN DN23520 DN23652 DN DN23522 DN23654 DN23786 $14.89 $16.60 $16.60 PATTERN TPI Incl. Tooth gonal gonal Straight Angle Right Left DN25002 DN25056 DN DN25004 DN25058 DN DN25006 DN25060 DN DN25008 DN25062 DN DN25010 DN25064 DN DN25012 DN25066 DN DN25014 DN25068 DN DN25016 DN25070 DN25124 $25.19 $25.19 $25.19 SW SERIES KNURLING WHEELS M Series Cobalt R Series Cobalt O Series High Speed Steel TPI Incl. Tooth Angle Straight PATTERN gonal Right gonal Left DN25306 DN25372 DN DN25308 DN25374 DN DN25310 DN25376 DN DN25312 DN25378 DN DN25314 DN25380 DN DN25316 DN25382 DN25448 $36.07 $33.39 $33.39 TPI Incl. Tooth Angle Straight PATTERN gonal Right gonal Left DN26502 DN26564 DN DN26504 DN26566 DN DN26506 DN26568 DN DN26508 DN26570 DN DN26510 DN26572 DN DN26512 DN26574 DN DN26514 DN26576 DN DN26516 DN26578 DN DN26518 DN26580 DN DN26520 DN26582 DN26644 $28.05 $28.05 $28.05 TPI Incl. Tooth Angle Straight PATTERN Male mond Female mond DN DN DN DN25612 DN26008 DN DN25614 DN26010 DN DN25616 DN26012 DN26078 $20.61 $32.06 $32.06 "SW" knurling wheels are technically designed to knurl against a square shoulder. With super precise workmanship, the wheels are made of heat treated High Cobalt Steel to withstand severe knurling operation. Knurl wheels are Titanium Nitrating coated to reduce the co-efficient of friction when knurling, increasing the quality and the force of knurling as well as the life of the knurl wheels. All SW Series knurl wheels are available only in cobalt and tin coated. CARIDE INSERTS SW2 Series Cobalt TPI Incl. Tooth Angle Straight PATTERN gonal Right gonal Left DN27402 DN27452 DN DN27404 DN27454 DN DN27406 DN27456 DN DN27408 DN27458 DN DN27410 DN27460 DN DN27412 DN27462 DN DN27414 DN27464 DN27514 $38.88 $38.88 $38.88 SW4 Series Cobalt PATTERN Master Catalog 479 TPI Incl. Tooth Angle Straight gonal Right gonal Left DN28002 DN28056 DN DN28004 DN28058 DN DN28006 DN28060 DN DN28008 DN28062 DN DN28010 DN28064 DN DN28012 DN28066 DN DN28014 DN28068 DN DN28016 DN28070 DN28124 $49.68 $49.68 $49.68 DEURRING

212 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS ROACHES KEYWAY ROACH SETS HIGH SPEED STEEL roach sets come in a durable plastic case (Dura-Case) and include broaches, bushings, shims, lubrication and operation guides. No. Of Combos KEYWAY ROACHES WITH SHIMS HIGH SPEED STEEL-AMERICAN STANDARD Type Standard Precision #1 Standard Set C-1 Standard Set C-1A Standard Set C-2 Standard Set C-2A Standard Set C-10A Standard Set C-10 Description 3 roaches: 1/16-1, 3/32-1, 1/8-1 5 ushings: 1/4-I, 5/16-I, 3/8-I, 7/16-I, 1/2-I 4 roaches: 1/8-II, 3/16-II, 1/4-III, 3/8-III 9 ushings: 1/2-II, 5/8-II, 3/4-II, 7/8-II, 1-III, 1-1/8-III, 1-1/4-III, 1-3/8-III, 1-1/2-III 4 roaches: 1/8-II, 3/16-II, 1/4-III, 3/8-III 9 ushings: 9/16- II, 11/16-II, 13/16-II, 15/16-III, 1-1/16-III, 1-3/16-III, 1-5/16-III, 1-7/16-III, 1-9/16-III 3 roaches: 1/8-II, 3/16-III, 1/4-III 9 ushings: 9/16-II, 11/16-II, 13/16-II, 15/16-III, 1-1/16-III, 1-3/16-III, 1-5/16-III, 1-7/16-III, 1-9/16-III 3 roaches: 1/8-II, 3/16-III, 1/4-III 9 ushings: 1/2-II, 5/8-II, 3/4-II, 7/8-II, 1-III, 1-1/8-III, 1-1/4-III, 1-3/8-III, 1-1/2-III 3 roaches: 1/8-II, 3/16-III, 1/4-III 18 ushings: 1/2-II, 9/16-II, 5/8-II, 11/16-II, 3/4-II, 13/16-II, 7/8 II,15/16-III, 1-III, 1-1/16-III, 1-1/8-III, 1-3/16-III, 1-1/4-III, 1-5/16-III, 1-3/8-III, 1-7/16-III, 1-1/2-III, 1-9/16-III 4 roaches: 1/8-II, 3/16-II, 1/4-III, 3/8-lll 18 ushings: 1/2-II, 9/16-II, 5/8-II, 11/16-II, 3/4-II, 13/16-II, 7/8-II, 15/16-III, 1-III, 1-1/16-III, 1-1/8-III, 1-3/16-III, 1-1/4-III, 1-5/16-III, 1-3/8-III, 1-7/16-III, 1-1/2-III, 1-9/16-III Dura Case HS $ HS $ HS $ HS $ HS $ HS $ HS $ TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD Used to cut keyways in machined round holes. Designed to be used with an arbor press or manually, it is suited for use in a variety of non-ferrous and ferrous materials. roach Size/Type Keyway Width Tolerance Dimensions No. Of Shims 1/16 -I /8 X 5 1/4 0 HS $ /32 -I /8 X 5 1/4 0 HS $ /8 -I /8 X 5 1/4 1 HS $ /32 -II /16 X 7 0 HS $ /8 -II /16 X 7 1 HS $ /32 -II /16 X 7 1 HS $ /16 -II /16 X 7 1 HS $ /16 -III /8 X 11 7/8 1 HS $ /4 -III /8 X 11 7/8 1 HS $ /16 -III /8 X 11 7/8 1 HS $ /8 -III /8 X 11 7/8 2 HS $64.19 ONE PASS KEYWAY ROACHES HIGH SPEED STEEL-AMERICAN STANDARD Used to cut keyways in machined round holes in a single pass. Designed to be used with an arbor press or manually, it is suited for use in a variety of non-ferrous and ferrous materials. FEATURES: Tapered broach allows teeth to cut key way to proper depth Manufactured from high speed steel Ground and hardened bar with cutting teeth on the edges Replacement shims also available Also available in metric sizes EXTRA SHIMS FOR STANDARD KEYWAY ROACHES HIGH SPEED STEEL-AMERICAN STANDARD Shims are designed to be placed between the bushing and the broach to allow the broach to cut deeper slots in the hole in succeeding passes. roach Size/Type roach Size/Type FEATURES: Tapered broach allows teeth to cut key way to proper depth Manufactured from high speed steel Ground and hardened bar with cutting teeth on the edges Replacement shims also available Keyway Width Tolerance roach Size/Type Keyway Width Tolerance Master Catalog Dimensions No. Of Shims 5/16 -IV /16 X 13 7/8 1 HS $ /8 -IV /16 X 13 7/8 2 HS $ /16 -IV /16 X 13 7/8 2 HS $ /2 -IV /16 X 13 7/8 3 HS $ /16 -IV /16 X 13 7/8 3 HS $ /8 -V /4 X 15 1/4 4 HS $ /4 -V /4 X 15 1/4 5 HS $ /8 -VI X 19 1/4 6 HS $ " -VI X 19 1/4 7 HS $ / /8 X 23 8 HS $ / /4 X 23 9 HS $ Dimensions Inches Min. Length of Cut Max. Length of Cut 1/8 II /16 X 10 3/4 1/4 1 1/2 HS-10208COP $ /32 II /16 X 10 3/4 1/4 1 1/2 HS-10210COP $ /16 II /16 X 10 3/4 1/4 1 1/2 HS-10212OP $ /16 III /8 X 18 1/2 5/ /16 HS-10312COP $ /4 III /8 X 18 1/2 5/ /16 HS-10316COP $ /16 III /8 X 18 1/2 5/ /16 HS-10320COP $ /8 III /8 X 18 1/2 5/ /16 HS-10324OP $ Thick. Length x Width 1/8 I /8 X 1/8 HS $2.70 1/8 II /8 X 3/16 HS $2.70 5/32 II /8 X 3/16 HS $2.70 3/16 II /8 X 3/16 HS $2.70 3/16 III /8 X 3/8 HS $2.70 1/4 III /8 X 3/8 HS $2.70 5/16 III /8 X 3/8 HS $2.70 3/8 III /8 X 3/8 HS $2.70 5/16 IV.078 6/1/4 X 9/16 HS $3.77 3/8 IV.062 6/1/4 X 9/16 HS $3.77 roach Size/Type Thick. Length x Width 7/16 IV.075 6/1/4 X 9/16 HS $3.77 1/2 IV.062 6/1/4 X 9/16 HS $3.77 5/8 V /4 X 3/4 HS $3.77 3/4 V /4 X 3/4 HS $3.77 7/8 VI /4 X 1 HS $3.77 1" VI /4 X 1 HS $ X 1 1/8 HS $ X 1 1/4 HS $ X 1 1/4 HS $ X 1 1/4 HS $6.37

213 ROACHES KEYWAY USHINGS KNURLED COLLAR & PLAIN TYPE Designed for use with standard keyway broaches for cutting keyways in machined holes. Keyway bushings act as a guide to guide the keyway broach through the hole. Plain Type: Used with Type IV & V broaches Knurled Collar Type: Designed for use with Type I, II & III broaches I Collared ushings for I roaches /Type Length 1/4 I 1 1/8 HS $ /16 I 1 1/8 HS $ /8 I 1 1/8 HS $ /16 I 1 1/8 HS $ /2 I 1 1/8 HS $10.63 II Collared ushings for II roaches /Type Length 1/2 II 1 11/16 HS $9.31 9/16 II 1 11/16 HS $9.31 5/8 II 1 11/16 HS $ /16 II 1 11/16 HS $9.31 3/4 II 1 11/16 HS $ /16 II 1 11/16 HS $9.31 7/8 II 1 11/16 HS $9.31 III Collared ushings for III roaches /Type Length 3/4 III 2 1/2 HS $ /16 III 2 1/2 HS $ /8 III 2 1/2 HS $ /16 III 2 1/2 HS $ " III 2 1/2 HS $12.50 STANDARD SQUARE PUSH ROACHES High Speed Steel Used to cut square shaped holes in machined round holes. Designed to allow broach to start in a plain round hole and cut a precisely shaped square hole in a single pass. Designed to be used with an arbor press or manually, it is suited for use in a variety of non-ferrous and ferrous materials. FEATURES: tooth is progressively larger and cuts slightly deeper than the previous tooth Manufactured from high speed steel Ground and hardened bar with cutting teeth on the edges Also available in metric sizes KEYWAY ROACH SETS Heavy Duty, High Speed Steel High speed steel Complete with wood case 30 piece set includes 5 broaches, 18 collared bushings and 7 shims for 47 keyway combinations. 9 piece set includes 3 broaches, 5 collared bushings and 1 shim for 15 keyway combinations. Plain Type ushing III Collared ushings for III roaches /Type Length 1 1/16 III 2 1/2 HS $ /8 III 2 1/2 HS $ /16 III 2 1/2 HS $ /4 III 2 1/2 HS $ /16 III 2 1/2 HS $ /8 III 2 1/2 HS $ /16 III 2 1/2 HS $ /2 III 2 1/2 HS $ /16 III 2 1/2 HS $14.95 IV Plain ushings for IV roaches /Type Length 1 7/16 4 HS $ /2 4 HS $ /16 4 HS $ /8 4 HS $ /16 4 HS $ /4 4 HS $ /16 5 HS $ /8 5 HS $ /16 5 HS $23.03 Size Square Tolerance Collard ushing IV Plain ushings for IV roaches /Type Length 2 5 HS $ /16 5 HS $ /8 5 HS $ /16 5 HS $ /4 5 HS $ /16 5 HS $ /8 6 HS $ /16 6 HS $ /2 6 HS $ /16 6 HS $ /8 6 HS $ /16 6 HS $ /4 6 HS $ /16 6 HS $ /8 6 HS $ /16 6 HS $ HS $39.15 Additional Sizes Available. Pilot Drill Size roach Length Master Catalog 481 Min LOC Max LOC 1/ #30 4 5/8 3/16 1/2 HS $ / #21 5 5/8 1/4 1/2 HS $ / # /16 1/4 5/8 HS $ / #1 6 7/8 1/4 3/4 HS $ / /64 7 1/4 3/4 HS $ / /64 7 1/4 3/8 1 HS $ / /64 8 1/8 3/8 1 HS $ / /64 9 5/8 3/8 1 1/4 HS $ / /64 9 7/8 3/8 1 1/4 HS $ / / /8 1/2 1 3/8 HS $ / / /8 1/2 1 3/8 HS $ / /2 12 1/2 1/2 1 3/8 HS $ / / /8 1/2 1 3/8 HS $ / / /8 1/2 1 1/2 HS $ / / /16 5/8 1 5/8 HS $ / /4 18 1/2 5/8 1 5/8 HS $ / / /8 5/8 1 5/8 HS $ / / /4 1/2 2 HS $ " / /2 1/2 2 HS $ No. Of Combos Type Standard Style A Standard Style /C Description 3 roaches: 1/16-A, 3/32-A, 1/8-A 5 ushings: 1/4, 5/16, 3/8, 7/16, 1/2 5 roaches: 1/8-, 3/16-, 1/4-C, 5/16-C,3/8-C 18 ushings: 1/2-, 9/16-, 5/8-, 11/16-, 3/4-, 13/16-, 7/8-, 15/16-C, 1 -C, 1-1/16-C, 1-1/8-C, 1-3/16-C, 1-1/4-C, 1-5/16-C, 1-3/8-C, 1-7/16-C,1-1/2-C, 1-9/16-C A $ A $ CARIDE INSERTS DEURRING

214 CHUCK JAWS LATHE WORKHOLDING MACHINE VISES RETENTION KNOS ER, DA, TG COLLETS ROACHES STANDARD HEXAGON PUSH ROACHES HIGH SPEED STEEL Used to cut hexagonal shaped holes in machined round holes. Designed to allow broach to start in a plain round hole and cut a precisely shaped hexagonal hole in a single pass. Designed to be used with an arbor press or manually, it is suited for use in a variety of non-ferrous and ferrous materials. FEATURES: tooth is progressively larger and cuts slightly deeper than the previous tooth Manufactured from high speed steel Ground and hardened bar with cutting teeth on the edges Also available in metric sizes INTERNAL HEX & SQUARE ROACHES HIGH SPEED STEEL Hex Size Tolerance Pilot Drill Size roach Length Min LOC Max LOC 1/ /8 4 5/8 3/16 3/8 HS $ / /32 5 1/2 1/4 1/2 HS $ / /16 5 9/16 1/4 5/8 HS $ / /32 6 1/4 3/4 HS $ / /4 6 1/2 1/4 3/4 HS $ / /32 7 3/4 3/8 1 HS $ / /16 8 1/4 3/8 1 HS $ / /32 8 1/4 3/8 1 1/4 HS $ / /8 9 3/8 1 1/4 HS $ / / /2 1 3/8 HS $ / / /4 1/2 1 3/8 HS $ / / /8 1/2 1 3/8 HS $ / /2 12 1/2 1/2 1 3/8 HS $ / / /4 1/2 1 1/2 HS $ / /8 16 7/8 5/8 1 5/8 HS $ / / /8 1 5/8 HS $ / /4 17 7/8 5/8 1 5/8 HS $ / /8 18 7/8 5/8 1 5/8 HS $ " /8 5/8 1 5/8 HS $ TOOLHOLDERS INDEXALE DRILLS TURNING & ORING ENDMILLS, DRILLS TAPS & REAMERS ARASIVES MEASURING TOOLS MRO & SAFETY FLAT STOCK/DRILL ROD FEATURES: Also referred to as wobble, blind hole, punch and rotary broaches For use with screw machines, CNC turning machines and presses Also available in special forms- torx, octagons, splines- please call for more information For Rotary roach Holders, please see the following page HEXAGONAL PUNCH ROACHES.315 SHANK Hex Size DOC L.051 5/64 1-1/4 HS $ /16 3/32 1-1/4 HS $ /64 7/64 1-1/4 HS $ /32 9/64 1-1/4 HS $ /64 5/32 1-1/4 HS $ /8 3/16 1-1/4 HS $ /64 7/32 1-1/4 HS $ /32 1/4 1-1/4 HS $ /16 9/32 1-1/4 HS $ /32 11/32 1-1/4 HS $ /4 3/8 1-1/4 HS $ /32 3/8 1-1/2 HS $ /16 3/8 1-1/2 HS $ /32 7/16 1-1/2 HS $ /8 1/2 1-1/2 HS $ /32 1/2 1-1/2 HS $ /16 1/2 1-1/2 HS $ /32 1/2 1-1/2 HS $ /2 1/2 1-1/2 HS $67.38 HEXAGONAL PUNCH ROACHES.500 SHANK.500 Hex Size DOC L 3/32 9/64 1-1/2 HS $ /64 5/32 1-1/2 HS $ /8 3/16 1-1/2 HS $ /64 7/32 1-1/2 HS $ /32 1/4 1-1/2 HS $ /16 9/32 1-1/2 HS $ /32 9/32 1-1/2 HS $57.58 HEXAGONAL PUNCH ROACHES.500 SHANK Master Catalog Hex Size DOC L 1/4 3/8 1-1/2 HS $ /32 7/16 1-1/2 HS $ /16 1/2 1-1/2 HS $ /32 9/16 1-1/2 HS $ /8 9/16 1-1/2 HS $ /32 5/8 2 HS $ /16 5/8 2 HS $ /32 5/8 2 HS $ /2 5/8 2 HS $ /32 5/8 2 HS $ /16 5/8 2 HS $ /32 5/8 2 HS $ /8 3/4 2 HS $ /32 3/4 2 HS $ /16 7/8 2 HS $ /32 7/8 2 HS $ /4 7/8 2 HS $84.77 HEXAGONAL PUNCH ROACHES.750 SHANK.750 Hex Size DOC L 3/8 1/2 2-1/2 HS $ /16 1/2 2-1/2 HS $ /2 1/2 2-1/2 HS $ /16 3/4 2-1/2 HS $ /8 3/4 2-1/2 HS $ /4 7/8 2-3/4 HS $ /8 7/8 2-3/4 HS $ /8 2-3/4 HS $ SQUARE PUNCH ROACHES.315 SHANK Hex Size DOC L 1/16 1/8 1-1/4 HS $ /32 9/64 1-1/4 HS $ /8 3/16 1-1/4 HS $ /32 1/4 1-1/4 HS $ /16 9/32 1-1/4 HS $ /32 11/32 1-1/4 HS $ /4 3/8 1-1/2 HS $ /32 3/8 1-1/2 HS $ /16 3/8 1-1/2 HS $ /32 3/8 1-1/2 HS $ /8 3/8 1-1/2 HS $67.57 SQUARE PUNCH ROACHES.500 SHANK Hex Size DOC L 3/32 9/64 1-1/2 HS $ /8 3/16 1-1/2 HS $ /32 1/4 1-1/2 HS $ /16 9/32 1-1/2 HS $ /32 11/32 1-1/2 HS $ /4 3/8 1-1/2 HS $ /32 7/16 1-1/2 HS $ /16 1/2 1-1/2 HS $ /32 9/16 1-1/2 HS $ /8 5/8 2 HS $ /16 5/8 2 HS $ /2 5/8 2 HS $ /16 3/4 2 HS $ /8 7/8 2 HS $84.77 SQUARE PUNCH ROACHES.750 SHANK.750 Hex Size DOC L 1/2 5/8 2-1/2 HS $ /16 3/4 2-3/4 HS $ /8 3/4 2-3/4 HS $ /4 7/8 2-3/4 HS $131.81

215 ROACH HOLDERS/AROR PRESSES ROTARY ROACH HOLDERS Rotary/Punch roaches can be used in a variety of machines to cut polygons in blind holes:any type of CNC or manual turning,milling,drilling or screw machine. The practical forming length of rotary/punch broaching is usually up to 1-1/2 times the size of the broach (measured across flats). Rotary roach Holders:For optimal tool life in large production settings these broaches are used in Rotary roach Holders.Holders and broaches are sold separately and available from stock for immediate delivery.these holders are for use on any type CNC or manual turning,milling,drilling or screw machine.the holder has an internal live spindle,which holds the end cutting broach tool.the centerline of the cutting tool is offset at 1 from the centerline of the work piece.this causes the broach to wobble creating a shearing effect as the broach is advanced into the work piece or vise versa as described below: roaching A Rotating Work Piece:In a turning or screw machine,the holder is mounted stationary while its internal live spindle and the broach rotates after contact with the rotating work piece (gram A).At the appropriate feed,the work piece is sheared by the pressure of the broach through a wobbling type action producing the polygon shape desired. roaching A Stationary Work Piece:In a milling or drilling machine,the holder is mounted into and rotates with the machine spindle while its internal live spindle along with the broach remains stationary upon contact with the stationary work piece (gram ).While the machine spindle is rotating,the broach s pressure shears the polygon shape into the work piece (wobbling type action). Punching Versus Rotary roaching:many applications can be achieved without the rotary broach holder.for the purpose of merely punching a polygon into an existing pilot hole,these broaches have successfully been used with universal machining methods. SINGLE LEVERAGE AROR PRESSES Shimmed ram cap permits take-up for potential wear Adjustable handle allows convenient handle positioning Smooth action gears permits finite ram control ase opening and slotted table plate for arbor work on models noted Pedestals also available Length *roach Not Included roach Depth For roaches With.315 diameter shanks 3-27/64 5/8 1-1/2 9/16 HS-P67040 $ /64 3/4 2 9/16 HS-P67048S $1, For roaches With.500 diameter shanks 4-17/32 3/ HS-P67048S $1, HS-P67064 $1, /32 1-1/ HS-P67068 $1, / HS-P67072 $1, For roaches With.750 diameter shanks 7-9/16 1-1/ HS-P67072HDS $2, / HS-P67076HS $2, AROR PRESSES The Palmgren arbor press delivers the heavy force needed for riveting, squeezing, punching, bending, and other pressing applications. Sturdy, cast-iron construction. Removable machined steel anvil provides accurate work support in four slot positions. Rugged steel ram is driven by a machined pinion. Punches or tools may be added to the end of the ram with the aid of a magnetic insert. ase drilled for mounting on a bench or pedestal. PALM is equipped with a handwheel to perform light and quick press work. The Arbor Press Stand provides a sturdy base and optimal height for easy operation. It has a slot on the top for pieces which need to extend below the base of the press table. Stand comes with built-in cup for catching expressed pieces. ase and top are cast iron; body of welded steel. Fits all 2-4 ton presses. Arbor Press Stand PALM Force Ton Leverage Ratio Force Ton Table Type Swing Anvil. RAM Size Max Work Hgt. Max Work Ram Dim. Throat PALM Height ase Dimension ase Dimension PALM Master Catalog 483 Wgt /2 3-3/8 4-1/2 3/4 x 3/4 9-3/8 5-1/8 x 9-3/8 22 lbs PALM $ /16 6-1/8 1 x /8 6-5/16 x 10-3/4 27 lbs PALM $ /8 6-5/ /4 x 1-1/4 15-1/8 11-1/8 x lbs PALM $ /2 6-5/8 12-5/8 1-1/2 x 1-1/ /8 x 17-7/8 102 lbs PALM $ Arbor Press Stand Top Dimension ase Dimension Height Wgt 11-13/16 x 22-1/ /16 x 22-1/ / lbs PALM $ Wgt 1 25:1 Solid 1 x 1 x 7-1/ /2 4-1/4 x 9-1/2 25 lbs DAKE $ /2 32:1 Solid 1 x 1 x /2 6 x lbs DAKE $ :1 Slotted 1 x 1 x 7-1/ /2 4-1/4 x 9 25 lbs DAKE $ /2 32:1 Slotted 1 x 1 x /2 6 x lbs DAKE $ :1 Slotted 1-1/4 x 1-1/4 x 16-1/ /4 x lbs DAKE $ Pedestals For Arbor Presses Description Dimension w.x.d x h Wgt Pedestal for Models & X 18 X DAKE $ Pedestal for Model x 21 x DAKE CARIDE INSERTS DEURRING