USER MANUAL DCS-930 VERSION 1.0

Transcription

1 USER MANUAL DCS-930 VERSION 1.0

2 Table of Contents Table of Contents Product Overview...4 Package Contents...4 System Requirements... 4 Introduction...5 Features... 6 Hardware Overview...7 Front View... 7 Rear View... 8 Installation...9 Hardware Installation... 9 Wireless Installation Considerations Starting the Camera Installation Wizard WPS - Hardware Push Button Setup Configuration...13 Using the Configuration Menu Live Video Setup > Wizard Internet Connection Setup Wizard Network Setup...18 Setup > Wireless Wireless Interface Setup > DDNS Setup > Image Setup Image Settings Setup > Video Video Configuration...22 Setup > Audio Setup > Motion Detect Setup > Mail Account...25 Time Schedule...26 Setup > FTP...27 FTP Server...27 Time Schedule...28 Setup > Time and Date Maintenance > Admin Maintenance > System Maintenance > Firmware Upgrade Status > Device Info Status > Active User Using & Configuring the DCS Wireless Security...38 What is WEP?...38 What is WPA?...39 Using & Configuring the DCS-930 with a NAT Router...40 Troubleshooting

3 Table of Contents Wireless Basics...49 Networking Basics...54 Check your IP address Statically Assign an IP address Technical Specifications

4 Section 1 - Product Overview Product Overview Package Contents DCS-930 Network Camera CAT5 Ethernet Cable Power Adapter Manual and Software on CD Quick Install Guide Camera Stand Note: Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller. System Requirements Computer with Microsoft Windows 7, XP, or Vista PC with 1.3GHz or above; at least 128MB RAM Internet Explorer 6 or above, Firefox 3.5 or above, Safari 4 Existing 10/100 Ethernet-based network or n wireless network 4

5 Section 1 - Product Overview Introduction Congratulations on your purchase of the DCS-930 Network Camera. The DCS-930 is a versatile and unique solution for your small office or home. Unlike a webcam, the DCS-930 is a stand-alone system with a built-in CPU that transmits high quality video images for monitoring. The DCS-930 can be remotely accessed, and controlled using a Web browser over the Intranet or Internet. The simple installation procedure and intuitive Web-based interface offer easy integration with your Ethernet/Fast Ethernet or n wireless network. The DCS-930 also comes with remote monitoring capability for a complete and cost-effective home security solution. 5

6 Section 1 - Product Overview Features Simple to Use The DCS-930 is a stand-alone system with a built-in CPU, requiring no special hardware or software such as PC frame grabber cards. The DCS-930 supports both ActiveX mode for Internet Explorer and Java mode for other browsers such as Firefox and Safari. Supports a Variety of Platforms Supporting TCP/IP networking, HTTP, and other Internet related protocols. The DCS-930 can also be integrated easily into other Internet/Intranet applications because of its standards-based features n Wireless or Ethernet/Fast Ethernet Support The DCS-930 offers wireless n and Ethernet/Fast Ethernet connectivity, making the DCS-930 easy to integrate into your existing network environment. The DCS-930 works with a 10 Mbps Ethernet based network or 100 Mbps Fast Ethernet based network for traditional wired environments, and works with n routers or access points for added flexibility. The Site Survey feature also allows you to view and connect to any available wireless networks. Web Configuration Using a standard Web browser, administrators can configure and manage the Network Camera directly from its own Web page via Intranet or Internet. This means you can access your DCS-930 anytime, anywhere in the world. Broad Range of Applications With today s high-speed Internet services, the Network Camera can provide the ideal solution for delivering live video images over the Intranet and Internet for remote monitoring. The Network Camera allows remote access using a Web browser for live image viewing, and allows the administrator to manage and control the Network Camera anytime, anywhere in the world. Many applications exist, including industrial and public monitoring of homes, offices, banks, hospitals, child-care centers, and amusement parks. 6

7 Section 1 - Product Overview Hardware Overview Front View Camera Lens Microphone Power and Link LED 7

8 Section 1 - Product Overview Rear View Power Connector Ethernet Connector Reset WPS LED WPS Button Camera Stand 8

9 Section 2 - Installation Connect the Ethernet Cable Installation Hardware Installation Connect the included Ethernet cable to the network cable connector located on the bottom panel of the DCS-930 and attach it to the network. Attach the External Power Supply Attach the external power supply to the DC power input connector located on the bottom panel of the DCS-930 and connect it to your wall outlet or power strip. Power is confirmed when the green LED Power Indicator located below the lens on the DCS-930 is illuminated. 9

10 Section 2 - Installation Wireless Installation Considerations The D-Link Wireless Network Camera lets you access your network using a wireless connection from anywhere within the operating range of your wireless network. However, the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines: 1. Minimize the number of walls and ceilings between your adapter and other network devices (such as your Network Camera) - each wall or ceiling can reduce your adapter s range from 3-90 feet (1-30 meters). 2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle, it looks over 42 feet (14 meters) thick. Position your devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. 3. Building Materials make a difference. A solid metal door or aluminum studs may weaken the wireless signal. Try to position your access points, wireless routers, and other networking devices where the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal. 4. Keep your product at least 3-6 feet or 1-2 meters away from electrical devices or appliances that generate RF noise. 5. If you are using 2.4GHz cordless phones or other radio frequency sources (such as microwave ovens), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use. 10

11 Section 2 - Installation Starting the Camera Installation Wizard Insert the Installation CD-ROM into your computer s optical drive to start the autorun program. The CD-ROM will open the Camera Installation Wizard. Simply click Start to go through the Installation Wizard, which will guide you through the installation process from connecting your hardware to configuring your camera. 11

12 Section 2 - Installation WPS - Hardware Push Button Setup Alternatively, you may create a WPS connect using the WPS Button on the back of the camera. To create a WPS connection: Step 1 Press and hold the WPS button on the side of the camera for three seconds. The blue WPS status LED above the button will blink. Step 2 Press the WPS button on your router within 60 seconds. The WPS button is usually on the front or side of your router. On some routers, you may need to log in to the web interface and then click on an onscreen button to activate the WPS feature. If you are not sure where the WPS button is on your router, please refer to your router s User Manual. The DCS-930 will automatically create a wireless connection to your router. While connecting, the green LED will flash and your camera will reboot. WPS Button 12

13 Section 3 - Configuration Configuration Using the Configuration Menu After completing the Camera Installation Wizard, you are ready to use your camera. The camera s built-in Web configuration utility is designed to allow you to easily access and configure your DCS-930. At the end of the wizard, click Go To Camera, or enter the IP address of your camera into a web browser, such as Internet Explorer. To log in, use the User name admin and the password you created in the Installation Wizard. If you did not create a password, the default password is blank. After entering your password, click OK. Note: If you are directly connecting your PC to the camera, or if you are using the camera on a closed network, the default IP is

14 Section 3 - Configuration Click the ActiveX or Java radio button to view live video. Please make sure that you have the latest version of Java application installed on your computer to ensure proper operation when viewing the video in Java mode. The Java application can be downloaded at no cost from Sun s web site. ( When you connect to the home page of your camera, you will be prompted to download ActiveX. If you want to use ActiveX to view your video images instead of Java, then you must download ActiveX. 14

15 Section 3 - Configuration Live Video ActiveX: For Windows Users that do not have Java installed, please choose this option to view video streaming on the Home page. Java: For Windows users that have Java installed, you can also use this for viewing video. Mac users must choose this mode to view video. Setup > Wizard You may choose to configure your network by using the Internet Connection Setup Wizard that includes step-by-step instructions. Otherwise, you may manually configure your connection using the Manual Internet Connection Setup. 15

16 Section 3 - Configuration Internet Connection Setup Wizard This wizard will guide you through a step-by-step process to configure your new D-Link Camera and connect the camera to the Internet. Click Next You may configure your camera using DHCP Connection (by default), where your DHCP server will automatically assign dynamic IP to your device. Static IP Address if your ISP has already assigned an IP address to you. PPPoE connection, where your camera is directly connected to the Internet through a DSL modem. * Input the DNS information if you have chosen and assigned a Static IP Address for your camera. Click Next 16

17 Section 3 - Configuration If you have a Dynamic DNS account and would like the camera to update your IP address automatically, enable DDNS and enter your host information. Click Next Enter a name for your camera. Click Next Configure the correct time to ensure that all events triggered, captured and scheduled at the right time. Click Next This page displays your configured settings. Click Apply to save and activate the setting, or Back to change your settings. Click Apply 17

18 Section 3 - Configuration This section allows you to configure your network settings. Network Setup DHCP: Static IP Client: Select this connection if you have a DHCP server running on your network and would like a dynamic IP address to be updated to your camera automatically. You may obtain a static or fixed IP address and other network information from your network administrator for your camera. A static IP address will ease you for accessing your camera in the future. IP Address: The fixed IP address Subnet Mask: The default value is Used to determine if the destination is the same subnet. Default Gateway: The gateway used to forward frames to destinations in a different subnet. Invalid gateway settings may cause the failure of transmissions to a different subnet. Primary DNS: Primary domain name server that translates names to IP addresses. Secondary DNS: Secondary domain name server to backup the Primary DNS. PPPoE Settings: If you are using a PPPoE connection, enable it and enter the User Name and Password for your PPPoE account. You can get this information from your Internet service provider (ISP). Port Settings: You may configure a Second HTTP port that will allow you to connect to the camera via a standard web browser. The port can be set to a number other than the default TCP ports 80. A corresponding port must be opened on the router. For example, if the port is changed to 1010, users must type instead of only UPnP Settings: Enable this setting to configure your camera as an UPnP device in the network. 18

19 Section 3 - Configuration This section allows you to setup and configure the wireless settings on your camera. Setup > Wireless SSID: Wireless Interface Service Set Identifier, an identifier for your wireless network. Channel: Connection Mode: The default setting is channel 6. Select the same channel that is using by other wireless devices within your network. When there is interference from the wireless networks that overlap with one another, you may change the channel to obtain maximum performance for your connection. Infrastructure is a wireless connection using an access point as a transmission point of all wireless devices. Ad-Hoc is a wireless connection used without an access point, where your DCS-930 is directly connecting to your PC. This is done using the on-board wireless adapter on the DCS-930 connected to a wireless adapter on the PC. Site Survey: This page will allow you to select a wireless network that the DCS-930 was able to detect. Wireless Security Mode: WPA-PSK / WPA2PSK Settings: For security, there are three choices; None, WEP, and WPA-PSK / WPA2-PSK. Select the same encryption method that is being used by your wireless device/ router. An appropriate Preshared Key, which is needed in order to connect to the wireless network.. 19

20 Section 3 - Configuration This section allows you to configure the DDNS setting for your camera. DDNS will allow all users to access your camera using a domain name instead of an IP address. Setup > DDNS DDNS: (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modified. The username and password are required when using the DDNS service. Enable: Server Address: Host Name: User Name: Password: Click to enable the DDNS function. Select your Dynamic DNS Server from the pull down menu. Enter the host name of the DDNS server. Enter your username or used to connect to the DDNS. Enter your password used to connect to the DDNS server. 20

21 Section 3 - Configuration This section allows you to configure the image settings for your camera. Setup > Image Setup Enable Antiflicker: Flip Image: Select this box to enable antiflicker. Image Settings Select this box to vertically rotate the video. If the camera is installed upside down, Flip Image and Mirror should both be checked. Mirror: Horizontally rotates the video. Brightness Control: Contrast Control: Saturation Control: Allows you to adjust the brightness level. Allows you to adjust the contrast level. Allows you to adjust the saturation level. 21

22 Section 3 - Configuration This section allows you to configure the video settings for your camera. Setup > Video Video Configuration Video Profile: This section allows you to change the Encode Type, Resolution, FPS, and Quality. Encode Type: The compression format used when viewing your camera. Resolution: FPS: Select the desired video resolution from three formats: 640x480, 320x240, and 160x120. The higher setting can obtain better quality. However, it will use more resource within your network. Select the optimal setting depending on your network status. Please note that the higher setting can obtain better quality. However, it will use more resources within your network. JPEG Quality: Choose one of five levels of image quality: Highest, High, Medium, Low, and Lowest. View Mode: Select the mode for viewing the camera image. Select Image for a still images, ActiveX for Internet Explorer, or Java for other web browsers. Light Frequency: Select the proper frequency (50Hz or 60Hz) to reduce image flicker. 22

23 Section 3 - Configuration Setup > Audio Enabling audio setting will allow you to listen to audio from the camera through your PC s audio output. Note: Please wait a few seconds for the camera to adjust the audio after the setting has been selected. Audio Settings: You may Enable or Disable the camera audio feed. Volume Settings: Select the desired volume percentage level. 23

24 Section 3 - Configuration Setup > Motion Detect Enabling Video Motion will allow your camera to use the motion detection feature. You may draw a finite motion area that will be used for monitoring. Motion Detection: Sensitivity: Detection Areas: Select this box to enable the motion detection feature of your camera. Specifies the measurable difference between two sequential images that would indicate motion. Please enter a value between 0 and 100. Use your mouse to click on the blocks that you would like to monitor for motion. 24

25 Section 3 - Configuration Setup > Mail Account This section allows you to configure the notification settings for your camera. SMTP Server This is the domain name or IP address of your external Address: server. Sender This is the address of the person sending the camera Address: snapshots. Receiver Address: User Name: Password: This is the address of the recipient. If the SMTP server uses authentication, you must enter your user name here. This is the password that corresponds to your user name to connect to the SMTP server. 25

26 Section 3 - Configuration Time Schedule Enable image to account: Choosing Always will start sending snapshots to the recipient s account right away. Choosing Schedule will allow you to schedule when to start and stop the sending of snapshots to the recipient s account. Interval: The frequency of the snapshot interval can also be configured from 1 to seconds. Test Account: This will send a snapshot to the account that you have configured in the section. If you have configured the SMTP account correctly, you will be able to send a test file to the account of the recipient. 26

27 Section 3 - Configuration Setup > FTP FTP Server This section allows you to configure a FTP server to receive images from the camera. Host Address: This is the IP address of the FTP server that you will be connecting to. Port Number: User Name: Default is port 21. If changed, external FTP client program must change the server connection port accordingly. Specifies the user name to access the external FTP server. If you are to upload snapshots to an FTP server you will need to fill in the Domain name or IP address of your external FTP server. The following user settings must be correctly configured for remote access. Password: Directory Path: Specifies the password to access the external FTP server. Specifies the destination folder in the external FTP server. Passive Mode: Enabling passive mode will allow access to an external FTP server if your camera is behind a router protected by a firewall. 27

28 Section 3 - Configuration Time Schedule Enable upload image to FTP server: Always: Schedule: Video Frequency: Base File Name: File: Test FTP Server: Checking this box will enable video uploads to the FTP server you have selected. Selecting this option allows snapshots to be uploaded to your FTP as soon as you click Apply. Selecting this option allows you to configure specific times when you want the snapshots to be uploaded to your FTP server. Users can select in frames per second (1, 2, 3 or auto, in auto this could go to 4). The user can also select a duration for each frame from 1 to seconds. This will be the name that precedes the time, for example DCS jpg. This means that the camera took a snapshot in the year 2010, July 21 at 16th hour (4 o clock), 42 minutes and 51 seconds and it is picture number one. If Overwrite is selected, only a few images will be constantly refreshed, depending on how many snapshots you choose to have sent. Select Date/Time Suffix and the pictures will be named with a date and time also. An example of this can be seen above under the Base file name category. Select a Sequence Number Suffix up to 1024 and all the pictures will be numbered from Up to 1024 pictures can be configured. Picture number 1025 will reset to number 1. This will send a snapshot to the FTP server that you have configured in the Upload section. If you have configured the FTP correctly, you will be able to see a test file on your FTP server. 28

29 Section 3 - Configuration Setup > Time and Date This section allows you to configure the settings of the internal system clocks for your camera. Test FTP Server: Synchronize NTP Server: Select the time zone for your region from the pull-down menu. Network Time Protocol will synchronize your camera with an Internet time server. Choose the one that is closest to your camera. Copy your Computer s Time Settings: Click to synchronize the time information from your PC. Set the Date and Time Manually: Select this to set the time manually. 29

30 Section 3 - Configuration This section allows you to change the administrator s password and configure the server settings for your camera. You can also manage the user account(s) that access to your camera. Maintenance > Admin Camera Name: LED Control: User Access Control: Specity a name for your camera Select Normal to enable the LED on the front of the device, or select off to disable the LED. Select Enable to enable user access control or Disable to allow only the administrator account to access the camera. Snapshot URL Authentication: Select Enable to allow access to the current camera snapshot via the web address indicated. Add User Account: User List: Create new user for accessing the video image. Enter the user name, password, and password confirmation, and click Add. A maximum of 8 user accounts can be added into the user list. Displays the account names of authorized users. 30

31 Section 3 - Configuration This section allows you to save and restore your configuration, restore the factory settings, and/or restart the camera. Maintenance > System 31

32 Section 3 - Configuration Your current firmware version and date will be displayed on your screen. You may go to the D-Link Support Page to check for the latest firmware versions available. Maintenance > Firmware Upgrade To upgrade the firmware on your DCS-930, please download and save the latest firmware version from the D-Link Support Page to your local hard drive. Locate the file on your local hard drive by using the Browse button. Then, open the file and click the Upload button to start the firmware upgrade. 32

33 Section 3 - Configuration This section displays all the details information about your device and network settings. Status > Device Info 33

34 Section 3 - Configuration This page lists all the active user s information including the User Name, IP address, and the time that camera access began. Status > Active User 34

35 Section 3 - Configuration D-Link s DCS-930 is a versatile and cost effective Network Camera for video monitoring. It can also serve as a powerful surveillance system in security applications. The DCS-930 can be used with any wired or n wireless router. This section explains how to view the camera from either the Internet or from inside your internal network. Materials Needed: Using & Configuring the DCS DCS-930 Network Camera 1 Ethernet Cable A Wired or Wireless router such as the D-Link DI-624 Wireless Router Ethernet based PC for system configuration Setting Up the DCS-930 For Use Behind a Router Installing a DCS-930 Network Camera on your network is an easy 4 step procedure: 1. Assign a Local IP Address to Your Network Camera 2. View the Network Camera Using Your Internet Explorer Web Browser 3. Access the Router with Your Web Browser 4. Open Virtual Server Ports to Enable Remote Image Viewing This section is designed to walk you through the setup process for installing your camera behind a router and enable remote video viewing. For the basic setup of the DCS-930, follow the steps outlined in the Quick Installation Guide. 35

36 Section 3 - Configuration After you have completed the setup of the DCS-930 outlined in the Quick Installation Guide you will have an operating camera that has an assigned IP Address. Because you are using a router to share the Internet with one or more PCs, the IP Address assigned to the Network Camera will be a local IP Address. This allows viewing within your Local Area Network (LAN) until the router is configured to allow remote viewing of the camera over the Internet. 1. Assign a Local IP Address to Your Camera Run the Setup Wizard program from the CD included with the DCS-930. Follow the steps in the Quick Installation Guide to configure the DCS-930. The camera will be assigned a local IP Address that allows it to be recognized by the router. Write down this IP Address for future reference. This is the IP Address assigned to your camera ( is only an example). You will probably have a different IP Address. Your Camera s IP Address 36

37 Section 3 - Configuration 2. View the Network Camera Using Your Internet Explorer Web Browser Run your Internet Explorer Web browser. In the address bar, type in the IP Address that was assigned to the Network Camera by the Installation Wizard program. The DCS-930 Home Page appears with a window displaying live video from the camera. You are able to view this screen from any PC running Internet Explorer on your LAN. Click on the Configuration button on the left side of the display. Scroll to the bottom of the Network Configuration page to display the ports used by HTTP and Streaming video. 37

38 Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DCS-930 offers the following types of security: WPA-PSK (Pre-Shared Key) WEP (Wired Equivalent Privacy) What is WEP? WEP stands for Wired Equivalent Privacy. It is based on the IEEE standard and uses the RC4 encryption algorithm. WEP provides security by encrypting data over your wireless network so that it is protected as it is transmitted from one wireless device to another. To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64- bit encryption. Keys are defined by entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for Information Interchange alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember. The ASCII string is converted to HEX for use over the network. Four keys can be defined so that you can change keys easily. 38

39 Section 4 - Security What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP: Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven t been tampered with. WPA2 is based on i and uses Advanced Encryption Standard instead of TKIP. User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computer s hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network. WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point. 39

40 Section 4 - Security Using & Configuring the DCS-930 with a NAT Router D-Link s DCS-930 is a versatile and cost effective Network Camera offering both video and audio monitoring. It can also serve as a powerful surveillance system in security applications. The DCS-930 can be used with any wired or n/g wireless router. This section explains how to view the camera from either the Internet or from inside your internal network. Materials Needed: 1 DCS-930 Network Camera 1 Ethernet Cable A Wired or Wireless router such as the D-Link DIR-655 Wireless Router Ethernet based PC for system configuration Setting up the DCS-930 for Use Behind a Router Installing a DCS-930 Network Camera on your network is an easy 4 step procedure: 1. Assign a Local IP Address to Your Network Camera 2. View the Network Camera Using Your Internet Explorer Web Browser 3. Access the Router with Your Web Browser 4. Open Virtual Server Ports to Enable Remote Image Viewing This section is designed to walk you through the setup process for installing your camera behind a router and enable remote video viewing. For the basic setup of the DCS-930, follow the steps outlined in the Quick Installation Guide. After you have completed the setup of the DCS-930 outlined in the Quick Installation Guide you will have an operating camera that has an assigned IP Address. Because you are using a router to share the Internet with one or more PCs, the IP Address assigned to the Network Camera will be a local IP Address. This allows viewing within your Local Area Network (LAN) until the router is configured to allow remote viewing of the camera over the Internet. 40

41 Section 4 - Security 1. Assign a Local IP Address to Your Camera Run the setup wizard from the CD included with the DCS-930. Follow the steps in the Quick Installation Guide to configure the DCS-930. The camera will be assigned a local IP Address that allows it to be recognized by the router. Write down this IP Address for future reference. 41

42 Section 4 - Security 2. View the Network Camera Using Your Internet Explorer Web Browser Run your Internet Explorer Web browser. In the address bar, type in the IP Address that was assigned to the Network Camera by the DCC program. The DCS-930 Live Video Page appears with a window displaying live video from the camera. You are able to view this screen from any PC running Internet Explorer on your LAN. Click on the Setup button on the left side of the display. Scroll to the bottom of the Network Setup page (see page 18) to display the ports used by HTTP and Streaming audio and video. 42

43 Section 4 - Security The Setup > Network Setup page displays the port settings for your camera. If necessary, these ports can be changed if they are already in use by other devices (e.g. in a multiple camera environment). Note: Both the HTTP port and RTSP port are required to be opened for the DCS

44 Section 4 - Security Router Set-Up and Installation The following steps generally apply to any router that you have on your network. The D-Link DIR-655 is used as an example to clarify the configuration process. Configure the initial settings of the DIR-655 by following the steps outlined in the DIR-655 Quick Installation Guide. 3. Access the Router with Your Web Browser If you have cable or DSL Internet service, you will most likely have a dynamically assigned WAN IP Address. Dynamic means that your router s WAN IP address can change from time to time depending on your ISP. A dynamic WAN IP Address identifies your router on the public network and allows it to access the Internet. To find out what your router s WAN IP Address is, go to the Status menu on your router and locate the WAN information for your router (as shown on the next page). The WAN IP Address will be listed. This will be the address that you will need to type in your Web browser to view your camera over the Internet. Your WAN IP Address will be listed on the router s Status > Device Info page. 44

45 Section 4 - Security Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to obtain a Static IP address from your ISP. A Static IP address is a fixed IP address that will not change over time and will be more convenient for you to use to access your camera from a remote location. The Static IP Address will also allow you to access your camera attached to your router over the Internet. 4. Open Virtual Server Ports to Enable Remote Image Viewing The firewall security features built into the DIR-655 router prevent users from accessing the video from the DCS-930 over the Internet. The router connects to the Internet over a series of numbered ports. The ports normally used by the DCS-930 are blocked from access over the Internet. Therefore, these ports need to be made accessible over the Internet. This is accomplished using the Virtual Server function on the DIR-655 router. The Virtual Server ports used by the camera must be opened through the router for remote access to your camera. Virtual Server is accessed by clicking on the Advanced tab of the router screen. Follow these steps to configure your router s Virtual Server settings: 1. Click Enabled. 2. Enter a different name for each entry. 3. Enter your camera s local IP Address (e.g., ) in the Private IP field. 4. Select TCP for HTTP port, both (TCP and UDP) for RTSP and both (TCP and UDP) for ports. 5. If you are using the default camera port settings, enter 80 into the Public and Private Port section, click Apply. 6. Scheduling should be set to Always so that the camera images can be accessed at any time. 45

46 Section 4 - Security Repeat the above steps adding the port 554 to both the Public and Private Port sections. A check mark appearing before the entry name will indicate that the ports are enabled. Important: Some ISPs block access to port 80 and other commonly used Internet ports to conserve bandwidth. Check with your ISP so that you can open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you will need to change the port the camera uses from 80 to something else, such as 800. Not all routers are the same, so refer to your user manual for specific instructions on how to open ports. Enter valid ports in the Virtual Server section of your router. Please make sure to check the box next to the camera name on the Virtual Server List to enable your settings. 46

47 Section 5 - Troubleshooting Troubleshooting 1. Why does the LED not light up? The power supply might be faulty. Confirm that you are using the provided DC 5V power supply for this network camera. Verify that the power supply is correctly connected. If the camera is functioning normally, the LED may have been disabled. See page 30 for information about how to enable the LED. 2. Why is the camera s network connection unreliable? There might be a problem with the network cable. To confirm that the cables are working, PING the address of a known device on the network. If the cabling is OK and your network is reachable, you should receive a reply similar to the following ( bytes = 32 time = 2 ms). Another possible problem may be that the network device such as a hub or switch utilized by the Network Camera is not functioning properly. Please confirm the power for the devices are well connected and functioning properly. 3. Why does the Network Camera work locally but not remotely? This might be caused by the firewall protection. Check the Internet firewall with your system administrator. The firewall may need to have some settings changed in order for the Network Camera to be accessible outside your local LAN. For more information, please refer to the section about installing your camera behind a router. Make sure that the Network Camera isn t conflicting with any Web server you may have running on your network. The default router setting might be a possible reason. Check that the configuration of the router settings allow the Network Camera to be accessed outside your local LAN. 4. Why does a series of broad vertical white lines appear through out the image? It could be that the CMOS sensor (a square panel situated behind the lens that measures the light signals and changes it into a digital format so your computer can present it into an image that you are familiar with) has become overloaded when it has been exposed to bright lights such as direct exposure to sunlight or halogen lights. Reposition the Network Camera into a more shaded area immediately as prolonged exposure to bright lights will damage the CMOS sensor. 47

48 Section 5 - Troubleshooting 5. The camera is producing noisy images. How can I solve the problem? The video images might be noisy if the Network Camera is used in a very low light environment. 6. The images are poor quality, how can I improve the image quality? Make sure that your computer s display properties are set to at least 6-bit color. Using 16 or 256 colors on your computer will produce dithering artifacts in the image, making the image look as if it is of poor quality. The configuration on the Network Camera image display is incorrect. The Web Configuration Video section of the Web management allows you to adjust the related-parameters for improved images such as: brightness, contrast, hue and light frequency. Please refer to the Web Configuration section for detailed information. 7. Why are no images available through the Web browser? ActiveX might be disabled. If you are viewing the images from Internet Explorer make sure ActiveX has been enabled in the Internet Options menu. You may also need to change the security settings on your browser to allow the ActiveX plug-in to be installed. If you are using Internet Explorer with a version number lower than 6, then you will need to upgrade your Web browser software in order to view the streaming video transmitted by the Network Camera. 48

49 Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless* connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers. A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link. 49

50 Appendix A - Wireless Basics What is Wireless? Wireless or WiFi technology is another way of connecting your computer to the network without using wires. WiFi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network. How does wireless work? Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN). Wireless Local Area Network (WLAN) In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues. 50

51 Appendix A - Wireless Basics Who uses wireless? Wireless technology as become so popular in recent years that almost everyone is using it, whether it s for home, office, business, D-Link has a wireless solution for it. Home Gives everyone at home broadband access Surf the Web, check , instant message, and etc Gets rid of the cables around the house Simple and easy to use Small Office and Home Office Stay on top of everything at home as you would at office Remotely access your office network from home Share Internet connection and printer with multiple computers No need to dedicate office space 51

52 Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called hotspots. Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers. Wireless network is easy to setup, but if you re installing it for the first time it could be quite a task not knowing where to start. That s why we ve put together a few setup steps and tips to help you through the process of setting up a wireless network. Tips Here are a few things to keep in mind, when you install a wireless network. Centralize your router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/ access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range. Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as away as possible from the router/access point. This would significantly reduce any interfere that the appliances might cause since they operate on same frequency. Security Don t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. 52

53 Appendix A - Wireless Basics Wireless Modes There are basically two modes of networking: Infrastructure All wireless clients will connect to an access point or wireless router. Ad-Hoc Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DCS-930 wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate. 53

54 Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is , check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters. If you are connecting to a wireless network at a hotspot (e.g. hotel, coffee shop, airport), please contact an employee or administrator to verify their wireless network settings. 54

55 Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows Vista - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Windows XP - Click on Start > Control Panel > Network Connections. Step 2 Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties. Step 3 Highlight Internet Protocol (TCP/IP) and click Properties. Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the router s LAN IP address is , make your IP address X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router ( ). Set Primary DNS the same as the LAN IP address of your router ( ). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings. 55

56 Appendix C - Technical Specifications SYSTEM REQUIREMENTS Operating System: Microsoft Windows XP, Vista, Windows 7 Internet Explorer 6 or above, Firefox 3.5 or above, Safari 4 Technical Specifications WIRELESS TRANSMIT OUTPUT POWER 16 dbm for 11b, 12 dbm for 11g, 12 dbm for 11n (typical) Networking Protocol IPV4, ARP, TCP, UDP, ICMP DHCP Client NTP Client (D-Link) DNS Client DDNS Client (Dyndns and D-Link) SMTP Client FTP Client HTTP Server PPPoE UPnP Port Forwarding LLTD UPnP-X1 BUILT-IN NETWORK INTERFACE 10/100BASE-TX Fast Ethernet b/g/n WLAN WIRELESS CONNECTIVITY b/g/n Wireless with WEP/WPA/WPA2 security SDRAM 32 MB FLASH MEMORY 4 MB RESET BUTTON Reset to factory default VIDEO Codecs MJPEG JPEG for still images VIDEO FEATURES Adjustable image size and quality Time stamp and text overlay Flip and Mirror RESOLUTION 640 x 480 at up to 20 fps 320 x 240 at up to 30 fps 160 x 120 at up to 30 fps 56

57 Appendix C - Technical Specifications LENS Focal length: 5.01 mm, F2.8 SENSOR VGA 1/5 inch CMOS Sensor Minimum Illumination 1 F2.8 View Angle Horizontal: 45.3 Vertical: 34.5 Diagonal: 54.9 DIGITAL ZOOM Up to 4x 3A CONTROL AGC (Auto Gain Control) AWB (Auto White Balance) AES (Auto Electronic Shutter) Power Input: V AC, 50/60 Hz Output: 5 V DC, 1.2 A External AC-to-DC switching power adapter DIMENSIONS (W x D x H) Including the bracket and stand: 65.8 x 65 x 126 mm Camera only: 27.2 x 60 x 96 mm WEIGHT 76.9 g (without bracket and stand) MAX POWER CONSUMPTION 2 W Operation Temperature 0 C to 40 C (32 F to 104 F) Storage Temperature -20 C to 70 C (-4 F to 158 F) Humidity 20-80% RH non-condensing Emission (EMI), Safety & Other Certifications FCC Class B IC C-Tick CE 57