POS 46X Series Manual Point-of-Sale Hardware System

Transcription

1 POS 46X Series Manual Point-of-Sale Hardware System P/N: July V2.1

2 Copyright All Rights Reserved Manual Version 2.1 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of the manufacturer. TRADEMARK Intel, Pentium and MMX are registered trademarks of Intel Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. ELO Touch is the registered trademark of ELO Touch Systems. 2

3 Safety IMPORTANT SAFETY INSTRUCTIONS 1. To disconnect the machine from the electrial power supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. 2. Read these instructions carefully. Save these instructions for future reference. 3. Follow all warnings and instructions marked on the product. 4. Do not use this product near water. 5. Do not place this product on an unstable cart,stand,or table.the product may fall, causing serious damage to the product. 6. Slots and openings in the cabinet and the back or bottom are provided for ventilation;to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered.the openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.this product should never be placed near or over a radiator or heat register,or in a built-in installation unless proper ventilation is provided. 7. This product should be operated from the type of power indicated on the marking label.if you are not sure of the type of power available, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord.do not locate this product where persons will walk on the cord. 9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock.never spill liquid of any kind on the product. FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. CE MARK This device complies with the requirements of the EEC directive 89/336/EEC with regard to Electromagnetic compatibility and 73/23/EEC Low Voltage Directive. 3

4 CAUTION ON LITHIUM BATTERIES There is a danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer s instructions. LEGISLATION AND WEEE SYMBOL 2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components. The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. 4

5 Table of Contents 1. Item Checklist Standard Items System View Front View Rear View Drivers Installation Driver list Chipset Driver Installation VGA Driver Installation LAN Driver Installation USB2.0 Driver Installation ELO Touch Screen Driver Installation POSTouch Touch Screen Driver Installation USB Smart Card Reader Driver Installation Peripherals Installation Magnetic (Smart) Card Reader / I-Button Installation Cash Drawer Installation Customer Display Installation Second Display Installation System Disassembly Open the Chassis Box Replace the HDD Replace the Power Supply Replace the Motherboard Tray...33 Appendix A: Specification...36 Appendix B: Jumper Settings...38 Appendix C: BIOS settings

6 1. Item Checklist Take the system out of the carton. Remove the unit by carefully clutching the foam inserts and remove slowly to protect the system. The following contents should be found in the carton: 1.1 Standard Items a. Driver CD b. Manual c. Power Cable 6

7 2. System View 2.1 Front View USB 1 & 2 LED Power Switch 2.2 Rear View LPT COM4 Cash Drawer 1 COM2 COM3 Mouse USB3 LAN Cash Drawer 2 COM1 Keyboard USB4 2 nd VGA Note: The maximum current that can be drawn from each COM port is 500 ma. 7

8 3. Drivers Installation 3.1 Driver list Folder/File <CD>:\B81.htm <CD>:\Common\INTEL\Chipset <CD>:\Common\INTEL\VGA\i85x <CD>:\Common\Lan_driver\R8139_810x <CD>:\Common\INTEL\USB20 <CD>:\Common\SmartCard\USB <CD>:\Common\Elo_Touch <CD>:\Common\POS_Touch File Description B81 Driver List Chipset Driver VGA Driver 10/100Mb LAN Driver USB 2.0 Driver USB Smart Card Reader Driver ELO Touch Screen Driver POSTouch Touch Screen Driver The following procedures are for Windows 2000/XP, other platforms are similar. 3.2 Chipset Driver Installation a. Double click "infinst_enu_ on the My Computer window. b. Click the "Next" button on the Welcome window. c. Click the "Yes" button on the License Agreement window. d. Click the Next button on the Readme Information window. 8

9 e. Click the Finish button and restart your system. 3.3 VGA Driver Installation a. Double click "win2k_xp147" on the My Computer window. b. Click the "Next" button on the Welcome window. c. Click the Next button on the Welcome window. d. Click the Yes button on the License Agreement window. 9

10 e. Click the Finish button and restart your system. 3.4 LAN Driver Installation a. Double click Setup on the My Computer window. b. Click the "Finish" button on the Maintenance complete window. c. Click the OK button and restart your system. 10

11 3.5 USB2.0 Driver Installation OS Requirements OS Windows XP Windows 2000 Windows 98SE/Me Windows 98 (Retail) Linux USB 2.0 requirements USB 2.0 drivers are provided in Service Pack 1 (SP1) for Windows XP, which is available through Windows Update. USB 2.0 drivers are available through Windows Update or Service Pack 4. USB 2.0 drivers are available on the Intel developer site. Developers and OEMs should contact Orange Ware. For end-users, if your device does not ship with Windows 98 drivers, contact your device or system manufacturer. If USB 2.0 drivers are not available, your device will operate at USB 1.1 speeds USB 2.0 support is available in kernel or later development kernels, or in the or later production kernel. More information. a. Right click My Computer on the windows desktop and select properties b. Select Hardware Device Manager on system properties. 11

12 c. Select Other Devices Universal Serial Bus (USB) Controller Properties on Device Manager. d. Select Device Update Driver. e. Click the Next button on the welcome window. f. Select Search for a suitable and click the Next button on the Install Hardware Device Drivers window. g. Select Specify a location and click the Next button on the Locate Driver Files window. 12

13 h. Press Browse to select driver and then click the OK button to next page. i. Click the Next button on Driver Files Search Results window. j. Click the Finish button to complete this process. k. Finished. 13

14 3.6 ELO Touch Screen Driver Installation a. Click sw on the My Computer window. b. Click the OK button on the Welcome window. c. Click the Unzip button on the WinZip Self-Extractor window. d. Select Install Serial Touchscreen Drivers and then click the Next button on the Welcome window. e. Click the Yes button on the License Agreement window. f. Click the Next button on the on the Select the COM ports window. 14

15 g. Select COM5 and click the Next button on the Choose the COM ports window. h. Click the Next button on the You have selected the COM ports window. i. Click the Finish button on the Setup Complete window j. Click the Yes button and restart your system. k. After the computer restarted, click Align on the Elo Touchscreen Properties window. l. Calibrate three red points. 15

16 3.7 POSTouch Touch Screen Driver Installation a. Double click Setup on the My Computer window. b. Click the Next button on the Welcome window. c. Click Yes button on the License Agreement window. d. Click Next button on the Choose Destination Location window. e. Click the Next button on the Select Program Folder window. f. Click the Finish button on the InstallShield Wizard Complete window. 16

17 g. Click the Continue Anyway button on the Hardware Installation window h. Click the OK button and restart your system i. After the computer restarted, select Programs TouchUtility Scan RS232 Touch Device. j. Automatically scan serial port for touch. k. Select Programs TouchUtility Touch Utility. l. Click Scale / Offset on the POSTouch Utility window. 17

18 m. Calibrate three red flash points. n. Select Device 9Pts Calibration on the POSTouch Utility window. o. Calibrate nine red flash points. Then, click Exit on the POSTouch Utility window. 3.8 USB Smart Card Reader Driver Installation a. Double click setup on the My Computer window. b. Click the yes button on the window. 18

19 c. Click the YES button and restart your system. 4. Peripherals Installation 4.1 Magnetic (Smart) Card Reader / I-Button Installation The module unit is tested and can be supplied at your request. This module is removed during transportation and can be connected by the user. a. Remove the screws (2) of the plastic cover on the right side of the display. 19

20 b. Slide the cover out as shown in the picture. c. Connect the MSR connector on the right side of the system. d. Slide the MSR into position as shown in the picture, and fasten it to the display housing by tightening the screws (2). 20

21 4.2 Cash Drawer Installation You can install a cash drawer through the cash drawer port. Please verify the pin assignment before installation Cash Drawer Pin Assignment 12 7 Pin Signal Pin Signal 1 GND 7 GND 2 DOUT bit0 8 DOUT bit2 3 DIN bit0 9 DIN bit1 4 12V / 24V 10 12V / 24V 5 DOUT bit1 11 DOUT bit3 6 GND 12 GND

22 4.2.2 Cash Drawer Controller Register The Cash Drawer Controller use one I/O addresses to control the Cash Drawer. The Cash Drawer Control Register and the Cash Drawer Status Register. Register Location: I/O port 4B8h Attribute: Read / Write Size: 8bit BIT BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 Attribute Reserved Reserved Read Read Write Write Write Write Bit 7: Reserved. Bit 6: Reserved. Bit 5: Cash Drawer2 DIN bit1 pin input status. = 1: the Cash Drawer2 closed or no Cash Drawer. = 0: the Cash Drawer2 opened. Bit 4: Cash Drawer1 DIN bit0 pin input status. = 1: the Cash Drawer1 closed or no Cash Drawer. = 0: the Cash Drawer1 opened. Bit 3: Cash Drawer2 DOUT bit3 pin output control. = 1: Opening the Cash Drawer2 = 0: Allow closing the Cash Drawer2 Bit 2: Cash Drawer2 DOUT bit2 pin output control. = 1: Opening the Cash Drawer2 = 0: Allow closing the Cash Drawer2 Bit 1: Cash Drawer1 DOUT bit1 pin output control. = 1: Opening the Cash Drawer1 = 0: Allow closing the Cash Drawer1 Bit 0: Cash Drawer1 DOUT bit0 pin output control. = 1: Opening the Cash Drawer1 = 0: Allow closing the Cash Drawer1 Note: Please follow the Cash Drawer control signal design to control the Cash Drawer Cash Drawer Control Command Example Use Debug.EXE program under DOS or Windows98 Command Cash Drawer 1 O 4B8 01 Opening O 4B8 00 Allow to closing Set the I/O address 4B8h bit0 =1 for opening the Cash Drawer1 by DOUT bit0 pin control. Set the I/O address 4B8h bit0 = 0 to allow closing Cash Drawer1. Command Cash Drawer 1 I 4B8 Check status The I/O address 4B8h bit4 =1 means the Cash Drawer1 is closed or no Cash Drawer. The I/O address 4B8h bit4 =0 means the Cash Drawer1 is open. 22

23 4.3 Customer Display Installation a. Take out the rubber cover. b. Take out the round plastic cover. c. Remove the screws (2). 23

24 d. Release the VFD cover. e. Install the stand base. f. Tighten the screws (2) to fix the stand base. 24

25 g. Install the VFD cover and tighten it with the screws (2). h. Install the stand stud. i. Install the VFD cable. 25

26 j. Install the short or the long pole. k. Assemble the VFD. l. Connect VFD cable to the COM port. Don t forget to setup the COM port power. 26

27 m. Finished. 4.4 Second Display Installation Please ensure that the system power is turned off before connecting the second display. Failure to do so may damage the electronics of the system, and is not covered by the product warranty. Note: Please set motherboard Jumper 15 to 1-2 (Refer to P.38 Item 12. Second Display Power Setting). a. Insert the male head of the VGA cable into the VGA port. b. Mount the second display on the rear of the system and tighten the screws (5) on the supporter. 27

28 c. Insert the other end of the VGA cable (male) into the VGA port of the system to establish the connection. Note: The procedure below is valid only for POS462 with Sanyo Torisan LCD Panel. After installing the second display with Sanyo Torisan LCD panel and the VGA driver under Windows XP, please set the monitor contents for second display as follows. Do not set the monitor contents from the Intel [R] Extreme Graphics 2 for Mobile icon in the taskbar, but follow the instructions below. a. Click on the desktop with the right mouse button. Select Properties. b. Select the Settings tab, then click on the Advanced button on the Display Properties window. 28

29 c. Select Intel [R] Extreme Graphics 2 for Mobile on the Default Monitor and Intel [R] window. d. Select Graphic Properties on the Default Monitor and Intel [R] window. e. Select Intel [R] Dual Display Clone and click Apply on the Intel [R] 82852/82855 GM/GME Graphics Controller window. 29

30 f. Click OK on the Confirm Desktop Change window. 5. System Disassembly 5.1 Open the Chassis Box The HDD, Power Supply, CPU + Cooler, Memory and Mini PCI SCSI Card can be replaced by opening the chassis box, which is located in the top part of the main modular box. a. Loosen the screws (2). b. Press the buttons and remove the rear cover towards you. 30

31 c. Pull the chassis box cover towards you by the handle, and lift it up. d. Fix the chassis box cover in the open position as shown in the picture. e. Replace the HDD and the power supply. HDD Power Supply 31

32 5.2 Replace the HDD Open the chassis box as described in chapter 5.1. a. Disconnect the cables (2) as shown in the picture. b. Remove the screws (4) to remove the HDD. 5.3 Replace the Power Supply Open the chassis box as described in chapter 5.1. a. Disconnect the cables (2) as shown in the picture. 32

33 b. Remove the screws (3). c. Remove the screws (2) to remove the power supply. 5.4 Replace the Motherboard Tray Open the chassis box as described in chapter 5.1. a. Lift the chassis box cover to disengage it from the chassis box. 33

34 b. Disconnect the cables (3) as shown in the picture. c. Disconnect the cables (4) as shown in the picture. d. Remove the screw (1) on the right side. 34

35 e. Remove the screw (1) on the left side. f. Remove the screw (1) on the motherboard. g. Pull the motherboard tray towards you to remove the motherboard. 35

36 Appendix A: Specification Main Name POS 462 POS 465 Mainboard B81 CPU Supports P4 2A / 2.6G, Celeron 2.0 / 2.4 / 2.5G, Mobile Celeron 1.2G Chipset Intel 852GM & ICH4 FSB 400Mhz System Memory 2 x DDR DIMM sockets supported with memory size up to 2GB Graphic Memory UMA Share Memory up to 64MB LCD Touch Panel LCD Size 12.1 TFT 15 TFT Brightness cd/m cd/m2 Maximal Resolution 800 x 600 / 1024 x x 768 Touch Screen Type Resistive Tilt Angle (Degree) 0 ~ 70 Storage HDD 1 x 3.5 Drive bay Flash Memory Compact Flash (Type I & II) Expansion Mini-PCI Socket 1 External I/O Ports Front I/O USB 2 (V2.0) Rear I/O PS/2 Keyboard 1 PS/2 Mouse 1 USB 2 (V2.0) Serial / COM 4 x powered COM ports (pin 1 / pin9 support +5Vv / +12V by Jumper) Parallel 1 LAN (10 / 100) 1 (RJ45) 2 nd VGA Output 1 female type connector with power Cash Drawer Port 2 x RJ11 (with 12V / 24V) Internal Interface USB USB 5 / 6 COM COM5 for touch, COM6 for MSR Control / Indicator Power Button 1 Indicator LED 1 36

37 Power Power Supply Internal 180W ATX switching mode power supply Environment EMC & Safety FCC, Class A, CE, LVD Operating 5 ~ 35 (41 ~ 95 ) Temperature Storage -20 ~ 60 (-4 ~95 ) Temperature Operating Humidity 20% ~ 80% RH non condensing Storage Humidity 20% ~ 80% RH non condensing Peripheral Input Device Second Display 8.4 / 10.4 /12.1 TFT LCD Magnetic Card 3 Tracks (RS-232 / PS2 Interface) Reader Smart / IC Card USB Interface Half-Insert Type Reader 3 in 1 MSR / IC MSR (RS-232) / Smart IC Card (USB) / I-Button (PS2) Card / I-Button Output Device Customer Display VFD / LCD Pole Display Communication Wireless LAN Mini PCI a / b / g WI-FI card and antenna Dimension POS462: 323x355x mm (W x D x Hmm/inch) POS465: 378x365x mm Weight OS Support POS462: N.W. 8kgs / 3.64lbs / G.W. 9kgs / 4.10lbs POS 465: N.W. 9kgs / 4.10lbs / G.W. 10kgs / 4.55lbs Windows XP, WEPOS, XP Embedded, XP Professional for Embedded, WIN 2000 Professional Embedded, WIN NT 4.0, Linux, Redhat

38 Appendix B: Jumper Settings B81 Motherboard JP3 JP5 JP6 JP15 JP14 JP13 JP12 JP10 JP11 JP1 JP2 JP4 JP9 38

39 Jumper Settings 1.CPU Frequency Setting Factory Default Setting Function JP4 (SHORT) FSB , 3-4 FSB Compact Flash Master/Slave Setting Function JP3 (SHORT) Master 1-2 Slave N/C 3. CMOS Operation Mode Function JP6 (SHORT) CMOS Normal N/C CMOS Reset 1-2 To clear the CMOS: 1. Remove AC power from the unit. 2. Open the cabinet. 3. Change the JP6 jumper setting from N/C to Wait 1 minute. 5. Change the JP6 jumper setting back to N/C. 6. Close the cabinet. 7. Apply AC power and continue. 4. POWER USB Power Setting (Reserved) Function JP14 (SHORT) +24V V Cash Drawer Power Setting Function JP8 (SHORT) Cash Drawer V V 3-4 Cash Drawer V +24V

40 6. COM1 Power Setting Pin Function JP9 (SHORT) DCD# V V 5-6 RI# V V COM2 Power Setting Pin Function JP11(SHORT) DCD# V V 5-6 RI# V V COM3 Power Setting Pin Function JP10 (SHORT) DCD# V V 5-6 RI# V V COM4 Power Setting Pin Function JP12 (SHORT) DCD# V V 5-6 RI# V V CPU Voltage Setting CPU Type JP1 (SHORT) JP2 (SHORT) P4 1-2, 3-4, 5-6, 7-8, 9-10, N/C Mobile Celeron 1.2G (1.3V) N/C 3-4,

41 11. LCD ID Setting Panel Resolution Number LVDS JP5 Bits Channel x Single SHORT SHORT SHORT SHORT x Single SHORT SHORT SHORT OPEN x Single SHORT SHORT OPEN SHORT x Dual SHORT SHORT OPEN OPEN x Single SHORT OPEN SHORT SHORT x Single SHORT OPEN SHORT OPEN 12. Second Display Power Setting Function JP15 (SHORT) +12V 1-2 NC ACPI Mode Setting Function JP7 (SHORT) Disable 1-2 Enable N/C 14. Power Mode Setting Function JP13 (SHORT) ATX Power N/C AT Power 1-2 Note: OPEN SHORT 41

42 Appendix C: BIOS settings 1. BIOS Setup Utility The BIOS setup defines how the system is configured. You need to run this program the first time you configure this product. You may need to run it again if you change the configuration. You need to connect a PC keyboard to the keyboard connector to run the BIOS setup utility. 2. Starting the BIOS Setup 1. Turn on or reboot this product. 2. Press the DEL key immediately after the product is turned on, or press the DEL key when the following message is displayed during POST (the Power on Self-Test). Press DEL to enter SETUP. 3. The main menu of the BIOS setup is displayed. 4. If the supervisor password is set, you must enter it here. 3. When a Problem Occurs If, after making and saving system changes with the Setup utility, you find that this product no longer boots, start the BIOS setup and execute the following. Load Optimized Defaults 42

43 4. BIOS Main Menu When the BIOS Main Menu is displayed, the following items can be selected. Use the arrow keys to select items and the Enter key to accept and enter the sub-menu. Note: The BIOS menu below is from B81 BIOS version B81FV10D.BIN. If you have a different BIOS version, the contents of the menu may differ. Standard CMOS Features Use this menu for basic system configuration. Advanced BIOS Features Use this menu to set the Advanced Features available on the system. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize the system s performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. Power Management setup Use this menu to specify your settings for power management. PnP/PCI Configurations This entry appears if your system supports Plug and Play and PCI Configuration. PC health status Displays CPU, System Temperature, Fan Speed, and System Voltages Value. 43

44 Load Optimized Defaults Use this menu to load the BIOS default values, i.e., factory settings for optimal performance system operations. While Award has designed the custom BIOS to maximize performance, the factory has the option to change these defaults to meet their needs. Set Supervisor Password Enables you to change, set, or disable the supervisor or user password. Set Password Change, set, or disable the password. It allows you to limit access to the system and to the setup, or just to the setup. Save & exit setup Save CMOS value changes to CMOS and exits setup. Exit without saving Ignores all CMOS value changes and exits setup. 44