Subaru 360 Sedan Parts Catalog

Transcription

1 Subaru 360 Sedan Parts Catalog Version /09/2002 MJ Christensen

2 ENGINE PAGE CASE & COVER 2-4 GASKET SET 5 ENGINE 6-8 OVERSIZE PISTON & RING 9 CRANKSHAFT COOLING FAN COVER & DUCT CLUTCH AIR CLEANER & FUEL SYSTEM CARBURETOR (HITACHI) ENGINE OIL SYSTEM MECHANICAL PUMP (MIKUNI) ELECTRICAL EQUIPMENT GENERATOR (NIPPON DENSO) STARTER MOTOR (HITACHI) DISTRIBUTOR (NIPPON DENSO) TRANSMISSION DIFFERENTIAL BODY CONTENT FRONT SUSPENSION FRONT AXLE WHEEL RIM & TIRE REAR SUSPENSION WHEEL CYLINDER & ANCHOR BLOCK FRONT BRAKE & REAR BRAKE REAR AXLE STEERING SYSTEM STEERING GEAR BOX STEERING SHAFT GEAR CHANGE EQUIPMENT BRAKE & CLUTCH PEDAL (LEFT HAND DRIVER) MASTER CYLINDER CLUTCH CONTROL SYSTEM BRAKE PIPING HAND BRAKE SYSTEM CHOKE, HEATER & FUEL CONTROL SYSTEM 78-79

3 ENGINE MOUNTING & MUFFLER FUEL SYSTEM OIL TANK BODY PARTS FRONT HOOD ENGINE HOOD BODY CONSTRUCTION INSTRUMENT PANEL FITTING DOOR DOOR WINDOW & REGULATOR LUGGAGE SHELF & TRAP DOOR FUEL FILLER FLAP ROOF & WINDSHIELD GLASS FRONT SEAT REAR SEAT FRONT & ENGINE HOOD LOCK FRONT & REAR BUMPER SIDE WINDOW SPARE TIRE MOUNTING & VENTILATOR AIR DUCT HEATER & DEFROSTER COMBINATION METER & SWITCH GROUP TOOK KIT BATTERY EQUIPMENT & WIRING HARNESS ELECTRICAL EQUIPMENT HEADLAMP ASSEMBLY LAMPS I LAMPS II WINDSHIELD & WIPER INNER TRIMMING & MAT SET BODY ACCESSORIES (INNER) BODY ACCESSORIES (OUTER)

4 BLANK PAGE

5 NOTE This parts catalogue is applied for SUBARU 360 Sedan (K111L) Chassies numbers 3588 and after. (1) The screws, bolts, and nuts on the above mentioned chassies Nos. are standardized ISO metric system, Specially the 3mm, 4mm, 5mm, and 12mm screws, bolts, and nuts are changed in their pitches, therefore these parts are not common to the previous ones. (2) Discrimination method The ISO metric system screws and bolts are marked on the head with 0.8mm diameter hemisphere emboss or dent, and the nuts are marked with 0.6mm dent on their top or side surface. Old ISO metric system Diameter & pitch Diameter & pitch 3mm x 0.6 3mm x 0.5 4mm x mm x 0.7 5mm x 0.9 5mm x mm x mm x 1.25 (3) The spare parts applied ISO metric system are labeled or stamped with the "ISO" mark.

6 - 2 -

7 CASE & COVER Item Part Number Nomenclature Q'ty Req Bolt Spring Washer Washer Cover (Transmission) Gasket (Transmission Cover) Cover III (Transmission) Gasket III (Transmission Cover) Spring (Accent Plunger) Plunger (Shifter ail) Screw (Flat Head) Spring Washer Ball (6.350) Spring (Shifter Fork Rail) Plug (8 x 10) Stud Bolt (Socket) (8 x 55 x 25) Bolt (Socket) (8 x 35 x 25) Bolt Spring Washer Bracket (Generator) Gasket IV (Transmission Cover) Cover IV (Transmission) Sash II (Transmission Cover) Sash III (Transmission Cover) Bolt Sash (Transmission Cover) Bracket (Generator) Bracket Bracket IV (Generator) Plug (14 x 8) Gasket (Fiber) Oil Seal (42 x 60 x 9) Guide (Oil) Bolt Stud Bolt Gutter (Transmission Oil) Stud Air Breather Unit 1 Remarks - 3 -

8 CASE & COVER Item Part Number Nomenclature Q'ty Req Remarks Crank Case Compl. 1 Includes: 15-17, 38, 39, 41, 42, 60, 61, Stud Stud (8 x 22 x 22) Washer Nut Gasket (Clutch Housing) Plug (Clutch Housing Timing Hole) Housing Comple (Clutch) Bolt Stud Nut Clutch Cover Bolt Gasket (Bearing Cover) Holder (Generator Drive Shaft Bearing) Bolt Oil Seal Compl Plug (22 x 8) Gasket (Fiber) Ball Bearing (75 x 105 x 16) Stud (8 x 60 x 12) Bushing VII (Crank Case) Oil Seal Stud Sleeve V (Crank Case) Stud Gasket (Transmission Case) Ball Bearing Transmission Case Compl Gasket II (Transmission Cover) Cover II (Transmission) Stud (8 x 56 x 16) 2-4 -

9 GASKET SET Item Part Number Nomenclature Q'ty Req Remarks Gasket Set 1 Consists of Gasket (Cylinder Head) Gasket (Bearing Cover) Gasket (Carburetor) Gasket (Clutch Housing) Gasket (Clutch Case Cover) Gasket (Intake Manifold) Gasket (Exhaust Manifold) Gasket (Cylinder) Gasket (Transmission Case) Gasket (Transmission Cover) Gasket (III Transmission Cover) Gasket (IV Transmission Cover) Gasket (Fiber) Gasket (Fiber) Gasket (II Transmission Cover) Gasket (Oil Pump) 1-5 -

10 - 6 -

11 ENGINE Item Part Number Nomenclature Q'ty Req Bolt (10 x 37 x 20) Spring Washer Washer Cylinder Head Cylinder Head II Gasket (Cylinder Head) Nut (8 x 6.5) Spring Washer Plate III (Exhaust Manifold) Exhaust Manifold Gasket (Exhaust Manifold) Cylinder Comple Cylinder Comple II Stud (8 x 35 x 12) Nut Stud Gasket (Cylinder) Gasket (Intake Manifold) Intake Manifold Stud Bracket II Nut Nipple (Intake Manifold) Washer Bolt (12 x 20 x 20) Crank Shaft Compl Needle Bearing Piston (1) Set (Right) 1 set Piston (2) Set (Left) 1 set Piston Pin Circlip (in) Piston Ring Set Gasket (Crank Case Cover) Ball Bearing Cover (Crank Case) Oil Seal (25 x 45 x 11) Bolt Woodruff Key Fan Compl Damper Unit (Fan) 1 Remarks - 7 -

12 ENGINE Item Part Number Nomenclature Q'ty Req Washer (15 x 26 x 2.3) Spring Washer Nut Spinner (Fan) Spring Washer Screw (Flat Head) 3 Remarks - 8 -

13 OVERSIZE PISTON & RING Item Part Number Nomenclature Q'ty Req Remarks Over Size Piston Ring Set 2 set mm Over Size Piston Ring Set 2 set mm Over Size Piston Ring Set 2 set mm Over Size Piston Ring Set 2 set mm Over Size Piston Ring Set 2 set mm Over Size Piston Ring Set 2 set mm Over Size Piston (1) Set 1 set mm Over Size Piston (1) Set 1 set mm Over Size Piston (1) Set 1 set mm Over Size Piston (1) Set 1 set mm Over Size Piston (1) Set 1 set mm Over Size Piston (2) Set 1 set mm Over Size Piston (2) Set 1 set mm Over Size Piston (2) Set 1 set mm Over Size Piston (2) Set 1 set mm Over Size Piston (2) Set 1 set mm - 9 -

14 - 10 -

15 CRANKSHAFT Item Part Number Nomenclature Q'ty Req Remarks Crankshaft Assy 1 Consists of Ball Bearing 2 # 6206C4 (NSK) Oil Seal (35 x 62 x 15) Spacer II (Crankshaft) Ball Bearing 3 # 6206C3 (NSK) Crankshaft III Washer (30 x 43 x 1.0) Connecting Rod Needle Bearing (29.75 x x 16.5) Crankpin Crankshaft Web Plug (Crankpin) Oil Slinger Labyrinth Packing 1 One Side Edge Planed off; Includes Roller (5 x 10) Spacer (Crankshaft) Crankshaft II Crankshaft I Bearing Big End Kit 2 Consists of 6 x 6, 8 x 1, 9 x Bearing 1 Not shown; Goes in fan end plate; NSK #

16 - 12 -

17 COOLING FAN COVER & DUCT Item Part Number Nomenclature Q'ty Req Fan Cover Clip (Fuel Pipe) Bolt Spring Washer Washer Air Duct Cowling 1 Remarks

18 - 14 -

19 LEVER-ACTION CLUTCH Item Part Number Nomenclature Q'ty Req Remarks Clutch Assy 1 Consists of 4-9, Spacer (Primary Reduction Pinion) 1 t = Spacer (Primary Reduction Pinion) 1 t = Spacer (Primary Reduction Pinion) 1 t = Primary Pinion Washer (27 x 36 x 0.5) Washer (27 x 36 x 0.7) Washer (27 x 36 x 0.8) Washer (27 x 36 x 0.9) 1 Select one Washer (27 x 36 x 1.0) Washer (27 x 36 x 1.1) Washer (27 x 36 x 1.2) Fly Wheel Unit 1 Includes Ring Gear (Starter) Friction Disc Pressure Plate Spring Washer Bolt Woodruff Key Clutch Release Lever Cotter Pin Castel Nut (6 x 5) Return Spring (Clutch) Bolt (6 x 34 x 10) Clutch Spring Cap (Clutch Spring) Clutch Cover 1 Includes 19, Rivet (4 x 15) Seat (Release Lever) Coupling Snap Ring (Inner - 32) Bearing (Clutch Release) Holder (Release Bearing) Snap Ring (Outer - 14) Bushing (Release Fork Shaft) Bolt Release Fork (Clutch) Bolt Guide II (Release Bearing)

20 LEVER-ACTION CLUTCH Item Part Number Nomenclature Q'ty Req Remarks Sealing (Release Fork Shaft) Release Fork Shaft Key Release Bolt Unit (Clutch) 1 Consists of 11-13,

21 BLANK PAGE

22 - 18 -

23 AIR CLEANER & FUEL SYSTEM Item Part Number Nomenclature Q'ty Req Remarks Air Cleaner Assy 1 Includes Wing Nut Cover (Air Cleaner Case) Spring (Air Cleaner) Washer (6.5 x 30 x 1) Element (Air Cleaner) 1 Oil Wet Type Case (Air Cleaner) Bolt Spring Washer Band (Clamp) Screw (4 x 28 x 24) Hose (Air Cleaner) Nut Spring Washer Washer Carburetor Gasket (Carburetor) Insulator (Carburetor) Saucer (Carburetor)

24 - 20 -

25 CARBURETOR (HITACHI) Item Part Number Nomenclature Q'ty Req Remarks Carburetor 1 HAB Screw Spring Washer Float Chamber Cover Gasket (Needle Valve) Needle Valve Gasket (Float Bowl Cover) Float (Carburetor) Throttle Valve Shaft Choke Valve Screw Screw Spring Washer Air Chamber Cover Gasket (Air Chamber Cover) Plug (Slow Air Bleed) 1 # Plug (Main Air Bleed) Idling Adjust Screw Spring (Idling Adjuster Scew) Plug (Bypass) Gasket (Bypass Plug) Washer (Main Nozzle) Main Nozzle Retainer (Main Nozzle) Gasket (Main Nozzle Retainer) Main Metering Jet 1 # Retainer (Main Metering Jet) Bracket Choke Lever Shaft Connecting Rod Spring (Choke Lever Shaft) Screw (Cable Bracket) Cotter Pin Throttle Adjust Lever Washer (Starting Lever) Nut (Throttle Lever) Spring Washer Throttle Leve Sleeve (Starting Lever)

26 CARBURETOR (HITACHI) Item Part Number Nomenclature Q'ty Req Remarks Starting Lever Spring (Throttle Adjust Lever) Spring (Starting Lever) Washer (Starting Lever) Slow Jet 1 # Spare Main Metering Jet 1 # Throttle Adjust Screw Throttle Valve

27 BLANK PAGE

28 - 24 -

29 ENGINE OIL SYSTEM Item Part Number Nomenclature Q'ty Req Remarks Bolt Spring Washer Clamp (Oil Pump Hose) Bolt Spring Washer Holder (Oil Pump Body) Hose Clamp Hose (Oil Pump) Gasket (Aluminum) Union Banjo (Oil Pump) Union Screw Cotter Pin Nut Spacer Oil Pump Cable Bolt (5 x 20 x 15) Spring Washer Washer Mechanical Pump Gasket (Oil Pump Body) Shaft & Screw Set 1 Consists of 2 x 1, Shaft (Oil Pump) Washer (10.5 x 18 x 0.8) Bushing (Oil Pump Shaft) Driven Gear (Distributor) Straight Pin (3.2 x 20) Washer Set Screw Bushing & Screw Set 1 Consists of 2 x 1, 24, 27,

30 - 26 -

31 MECHANICAL PUMP Item Part Number Nomenclature Q'ty Req Mechanical Pump Compl Screw & Spring Washer Oil Seal Worm Bearing A "O" Ring Driving Worm Spring (Differential Plunger) Cap (Differential Cylinder) Plunger (Differential) Cylinder (Differential) Plunger Body (Pump) Banjo Connection Banjo Bolt Set Banjo Washer Plunger Guide Set Washer (Guide) Cam Ring (Cam Shaft) "O" Ring Diaphragm Plate (Cam Casing) Screw & Spring Washer Washer (Aluminum) Body (Check Valve) Washer (Aluminum) Steel Ball Spring (Check Valve) Outlet Screw Nut Spring Washer Spring (Leve Return) Control Lever "O" Ring (Cam Shaft) Cam Shaft Cotter Pin (Cam) Bracket (Return Spring) Screw 2 Remarks

32 - 28 -

33 ELECTRICAL EQUIPMENT Item Part Number Nomenclature Q'ty Req Remarks Nut Spring Washer Washer Pulley (Generator) Woodruff Key Spacer (Generator Pulley) Ball Bearing Driving Gear (Distributor) Driving Shaft (Distributor) Regulator 1 Nippon Denso Ignition Coil Cap (Spark Plug Cord) Cord (Distributor) Distributor 1 Nippon Denso Cord (Spark Plug) Sealing (Spark Plug Cap) Spark Plug Bolt Generator 1 Nippon Denso Nut Spring Washer Washer Clamp (Distributor) Washer (Distributor Clamp) Spring Washer Bolt (6 x 16 x 14) V Belt (1/2" x 24") Bolt (8 x 100 x 16) Starter Motor 1 Hitachi Adjusting Washer t = 0.33mm Adjusting Washer 0-1 t = 0.6mm Adjusting Washer t = 0.8mm

34 - 30 -

35 GENERATOR (NIPPON DENSO) Item Part Number Nomenclature Q'ty Req Generator Nut Spring Washer Pulley (Generator) Front Cover (Generator) Oil Felt (Generator Bearing) Cover I (Oil Felt) Ball Bearing Plate (Generator Bearing) Cover II (Oil Felt) Spacer (Armature) Key Armature Spacer (Generator Bearing) Ball Bearing Field Coil York (Generator) Bolt (Terminal) Insulator (Terminal) Plate (Terminal) A Terminal (Generator) Brush I (Commutator) Brush II (Commutator) Spring (Commutator Brush) Rear Cover (Generator) Bolt (6 x 14.6 x 7) 2 Remarks

36 - 32 -

37 STARTER MOTOR (HITACHI) Item Part Number Nomenclature Q'ty Req Remarks Starter Motor Bolt (5 x 130 x 17) Starter Switch Gasket (Starter Pinion Housing) Bolt (5 x 30 x 10) Housing (Starter Pinion) 1 Includes Bushing (Armature Shaft) Cotter Pin Lever (Starter Pinion) Pin (Starter Pinion Lever) Sealing (Starter Pinion Housing) Frame (Starter Field) Band (Starter Motor) Holder (Commutator End) Bushing (Armature Shaft) Spring (Commutator Brush) Brush I (Commutator) Brush II (Commutator) Plug (Commutator End Holder) Screw Screw Spring (Armature Brake) Washer (9.8 x 10.5 x 1.0) Washer (9.8 x 26 x 0.6) Plate (Armature Brake Spring) Armature (Starter Motor) Pinion (Starter Motor) Washer (9.8 x 18 x 1.2) Washer (9.8 x 18 x 0.2) Washer (9.8 x 18 x 1.7)

38 - 34 -

39 DISTRIBUTOR Item Part Number Nomenclature Q'ty Req Distributor Assembly Cap Assembly Rotor Head Contact Set (Points) 1 set Breaker Plate Assembly Terminal Assembly Terminal Cover Pinion Set 1 set Condenser Unit Cap Clamp Cap Clamp Set (2) 1 set Screw Housing Thrust Needle Set 1 set Shaft Assembly Governer Spring Set 1 set Governer Weight Set 2 set Cam Assembly Set 1 set Remarks

40 - 36 -

41 TRANSMISSION Item Part Number Nomenclature Q'ty Req Remarks Set Screw (Shifter Fork) Arm (Selector) Arm (Shifter) Shaft (Shifter Arm) Arm II (Selector) Rail III (Shifter Fork) 1 = Arm II (Shifter) Nut Lock Washer (8.5 x 24 x 0.8) Plug (8 x 12) Ball (16.350) Spring (Shifter Fork Rail) 3 Discern Blue Lever (Over Drive) Shaft (Over Drive Lever) Rail II (Shifter Fork) 1 = Shifter Fork II Rail (Shifter Fork) 1 = Shifter Fork Shifter Fork III Shaft Comple (Gear Selector Arm) Snap Ring (Out) Ring (Synchronizer) 1 Number of Grooves: Spring (Synchronizer Hub) Sleeve (Synchronizer) Insert (Synchronizer Hub) Hub (Synchronizer) Gear Compl (Second Drive) 1 Number of Teeth: Bushing (Second Drive Gear) Washer (25 x 28 x 1) Gear (Low Drive) 1 Number of Teeth: Bushing (Over Drive Drive Gear) Needle Bearing (25 x 30 x 25) Gear (Over Drive Drive) 1 Number of Teeth: Ring II (Synchronizer) Washer (20.5 x 34 x 2) Spring (Synchronizer Hub) Insert (Synchronizer Hub)

42 TRANSMISSION Item Part Number Nomenclature Q'ty Req Remarks Sleeve II (Synchronizer) Nut (16 x 8) Lock Washer (16.5 x 40 x 1) Stopper (Synchronizer) Pinion (Final) 1 Number of Teeth: Bolt Spring Washer Plate III (Crank Case Bearing) Ball Bearing 1 #6305 (NSK Special Type) Shaft (Transmission Main) Gear Compl (Transmission Main Drive) 1 Number of Teeth: Needle Bearing (18 x 25 x 15) 2 TA Key Bolt (6 x 25.5 x 25.5) 2 Stamp H Plate (Crank Case Bearing) Ball Bearing 1 # Plate II (Crank Case Bearing) Tooth Lock Washer (6.4 x 11 x 0.6) Nut Gear (Primary) 1 Number of Teeth: Lock Washer (34.1 x 49 x 1) Nut (34 x 6) Washer (15.3 x 28 x 0.8) Gear Compl (Reverse Idler) 1 Number of Teeth: Bushing (Reverse Idler Gear) Washer (15.3 x 28 x 2) Shaft (Reverse Idler Gear) Gear (Transmission Counter) Ball Bearing (20 x 42 x 12) 2 #6004 NR Gear (Over Drive Drive) 1 Number of Teeth: "O" Ring (7.8 x 1.5) Hub II (Synchronizer)

43 BLANK PAGE

44 - 40 -

45 DIFFERENTIAL Item Part Number Nomenclature Q'ty Req Remarks Universal Joint Set 2 Consists of 1, 2, Needle Unit (Universal Joint) Shaft (Universal Joint) Yoke (Universal Joint) Washer (11.2 x 24 x 1.48) Washer (11.2 x 24 x 1.50) Washer (11.2 x 24 x 1.52) Washer (11.2 x 24 x 1.54) Washer (11.2 x 24 x 1.56) Washer (11.2 x 24 x 1.58) Washer (11.2 x 24 x 1.60) Washer (11.2 x 24 x 1.65) 4 Select One Washer (11.2 x 24 x 1.49) Washer (11.2 x 24 x 1.51) Washer (11.2 x 24 x 1.53) Washer (11.2 x 24 x 1.55) Washer (11.2 x 24 x 1.57) Washer (11.2 x 24 x 1.59) Washer (10.8 x 24 x 1.48) Washer (10.8 x 24 x 1.50) Washer (10.8 x 24 x 1.52) Washer (10.8 x 24 x 1.54) Washer (10.8 x 24 x 1.56) Washer (10.8 x 24 x 1.58) Washer (10.8 x 24 x 1.60) Washer (10.8 x 24 x 1.65) 4 Select One Washer (10.8 x 24 x 1.49) Washer (10.8 x 24 x 1.51) Washer (10.8 x 24 x 1.53) Washer (10.8 x 24 x 1.55) Washer (10.8 x 24 x 1.57) Washer (10.8 x 24 x 1.59) Side Gear (Differential) Pinion (Differential) Block (Pinion Shaft) Block (Pinion Shaft) 1 Select One Block (Pinion Shaft) Washer (65.2 x 80 x 0.950) Washer (65.2 x 80 x 0.975) 2 Select One

46 DIFFERENTIAL Item Part Number Nomenclature Q'ty Req Remarks Washer (65.2 x 80 x 1.000) Washer (65.2 x 80 x 1.025) 2 Select One Washer (65.2 x 80 x 1.050) Shaft (Differential Pinion) Crow (Universal Joint) Bolt (6 x 14 x 11) Lock Washer (Oil Seal Sleeve) Sleeve (Oil Seal) Washer (77 x 82 x 0.2) Final Reduction Gear 1 Number of Teeth: Straight Pin (4 x 35) Differential Case Lock Washer (9.2 x 15 x 1) Bolt (9 x 21 x 6)

47 BLANK PAGE

48 - 44 -

49 FRONT SUSPENSION Item Part Number Nomenclature Q'ty Req Remarks Oil Damper (Front) 2 Includes Nut (10) Washer A (Oil Damper) Rubber Bushing (Oil Damper) Cushion Rubber (Oil Damper) Washer (Oil Damper) Nut (10) Rubber Bushing (Oil Damper) Washer C (Oil Damper) Washer Nut Spring Washer Trailing Arm (Right) 1 Includes 35, Trailing Arm (Left) 1 Includes 35, Shim Washer (Inner Bracket) Plate (Center Spring) Center Spring (Front) Boot (Torsion Bar - Front) Center Arm (Front) Torsion Bar (Front - Right) Torsion Bar (Front - Left) Nut (8) Spring Washer Spring Washer Screw Bolt (8 x 63) Bracket (Center Arm - Front) Bolt (8 x 28) Nut Bolt (Center Arm - Front) Inner Bracket 2 Includes Rubber Bushing (Inner Bracket) Plug (Trailing Arm) Outer Bracket 2 Includes Rubber Bushing (Outer Bracket) Washer (Outer Bracket) Boot (Trailing Arm) Cotter Pin

50 FRONT SUSPENSION Item Part Number Nomenclature Q'ty Req Spring Washer Nut Nylon Bushing (Trailing Arm) 4 Remarks

51 BLANK PAGE

52 - 48 -

53 FRONT AXLE Item Part Number Nomenclature Q'ty Req Nut (10) Spring Washer Washer Bolt (Brake Drum) Packing (Cap) Cap (Right) Spring Washer Screw Nut (16) Washer (Locking) Washer (Knuckle - Outer) Roller Bearing Cap (Left) Brake Drum (Front) Roller Bearing Oil Seal Spacer (Knuckle - Inner) Bolt (8 x 18) Shim (Thrust Washer) Shim (Thrust Washer) Plug (King Pin) Shim (Thrust Washer) Shim (Thrust Washer) Shim (Thrust Washer) Nut (8) Spring Washer Knock Pin (King Pin) Knuckle (Right) Knuckle (Left) Thrust Washer (King Pin - Lower) Thrust Washer (King Pin - Upper) Cover (Thrust Washer) King Pin Grease Nipple Cover (King Pin) "O" Ring Spring Washer Bolt (6 x 7.5) King Pin Set 1 Remarks Consists of 19-14, 27, 30-36, page 46 - Item

54 - 50 -

55 WHEEL RIM & TIRE Item Part Number Nomenclature Q'ty Req Remarks Wheel Cap Bolt (Rim) Rim A (Tire) Rim B (Tire) Tire - Tube ( P R) 5 Consists of 7, Tube Tire (White Line) Spring Washer Nut

56 - 52 -

57 REAR SUSPENSION Item Part Number Nomenclature Q'ty Req Remarks Oil Damper (Rear) 2 Consists of 2-9, Nut (10) Nut (10) Washer A (Oil Damper) Rubber Bushing (Oil Damper) Washer C (Oil Damper) Rubber Bushing (Oil Damper) Washer (Oil Damper) Pin (Oil Damper - Rear) Cushion Rubber (Oil Damper) Center Arm (Rear) Nut Bolt (Center Arm - Rear) Torsion Bar (Rear Right) Rubber Boot (Center Arm) Torsion Bar (Rear Left) Rubber Bushing (Radius Arm) Radius Arm (Rear Right) Radius Arm (Rear Left) Cover (Radius Arm) Spring Washer Bolt (Radius Arm Cover) Nut Washer

58 - 54 -

59 WHEEL CYLINDER & ANCHOR BLOCK Item Part Number Nomenclature Q'ty Req Remarks Wheel Cylinder (Front Upper Right) Includes 5, Wheel Cylinder (Front Upper Left) Wheel Cylinder (Front Lower Right) Includes Wheel Cylinder (Front Lower Left) Union Bolt (Wheel Cylinder - Front) Cap (Wheel Cylinder) Air Bleeder (Wheel Cylinder - Front) Screw (Wheel Cylinder - Front) Lock Spring (Wheel Cylinder - Front) Adjuster Wheel (Wheel Cylinder - Front) 2 Right-Handed Screw Adjuster Wheel (Wheel Cylinder - Front) 2 Left-Handed Screw Supporter (Wheel Cylinder - Front) 2 Left-Handed Screw Supporter (Wheel Cylinder - Front) 2 Right-Handed Screw Boot (Wheel Cylinder - Front) Piston (Wheel Cylinder - Front) Cup (Wheel Cylinder - Front) Gasket (Wheel Cylinder) Wheel Cylinder (Rear) 2 Includes Gasket (Wheel Cylinder) Union Bolt (Wheel Cylinder) Cap (Wheel Cylinder) Air Bleeder (Wheel Cylinder - Rear) Cup (Wheel Cylinder - Rear) Piston (Wheel Cylinder - Rear) Supporter (Wheel Cylinder - Rear) Boot (Wheel Cylinder - Rear) Anchor Block 2 Includes Supporter (Anchor Block - Left) Adjuster (Anchor Block - Left) Adjuster (Anchor Block - Right) Supporter (Anchor Block - Right)

60 - 56 -

61 FRONT BRAKE & REAR BRAKE Item Part Number Nomenclature Q'ty Req Remarks Pipe (Brake. Front) Nut Spring Washer Set Pin (Brake Shoe. Front) Back Plate (Front Right) Back Plate (Front Left) Wheel Cylinder (Front Upper Right) Wheel Cylinder (Front Upper Left) Wheel Cylinder (Front Lower Right) Wheel Cylinder (Front Lower Left) Spring (Brake Shoe. Front) Brake Shoe (Front) Seat (Brake Shoe. Front) Set Spring (Brake Shoe. Front) Nut Spring Washer Wheel Cylinder (Rear) Spring (Brake Shoe. Rear Upper) Cotter Pin Pin (Lever A) Lever A (Brake Shoe. Rear Upper) Brake Shoe (Rear) Shoe (Supporter) Lock Washer (Supporter) Nut Supporter (Brake Shoe) Spring (Brake Shoe. Rear Lower) Washer Spring (Lever B. Right) Spring (Lever B. Left) Lever B (Brake. Rear Lower Right) Lever B (Brake. Rear Lower Left) Pin (Lever B) Anchor Block Back Plate (Rear Right) Back Plate (Rear Left)

62 - 58 -

63 REAR AXLE Item Part Number Nomenclature Q'ty Req Remarks Nut Spring Washer Washer Hub (Rear Right) Hub (Rear Left) Ball Bearing Nut (Bearing. Rear) Oil Seal Spacer C (Bearing. Rear) Plate (Locking) Bolt (8 x 25) Nut (10) Spring Washer Washer Brake Drum (Rear) Bolt (Brake Drum) Cotter Pin Castle Nut (16) Washer Spacer B (Bearing. Rear) Ball Bearing Spacer A (Bearing. Rear) Oil Seal Rear Axle 2 Includes Protector (Oil Seal) Bolt Knock Pin (Rear Axle) Bolt (Rear Axle) Clip Boot (Rear Axle) Clip

64 - 60 -

65 STEERING SYSTEM Item Part Number Nomenclature Q'ty Req Remarks Tie Rod End 2 Includes 2, Dust Seal (Tie Rod End) Grease Nipple Screw Washer Clamp (Steering Shaft Cover) Washer (8.5) Washer Spring Washer Bolt (8 x 16) Washer (5.3) Spring Washer Nut Tapping Screw Plate (Dust Cover Seal) Dust Seal (Steering Shaft) Steering Gear Box Assy Turnbuckle Knuckle Arm Castle Nut (10) Cotter Pin Cotter Pin Castle Nut Key Nut (16) Nut (16)

66 - 62 -

67 STEERING GEAR BOX Item Part Number Nomenclature Q'ty Req Remarks Steering Gear Box Assy 1 Consist of Cover (Rack) Bushing (Rack Eccentric) Lock Washer (Eccentric Bushing) Steering Gear Box Snap Ring (Rubber Boot) Bushing (Steering Gear Box) Oil Seal Pinion (Steering Gear Box) Bolt Spring Washer Cap (Pinion) Thrust Washer (Pinion) Bolt Spring Washer Washer Bushing (Rack) Nut Lock Washer (Rack) Stopper (Rack) Rack (Steering Gear Box) Cotter Pin Ball Seat Tie Rod Tie Rod (Left) Spring (Ball Seat) Spring Seat Spacer Cap (Rack) Cover (Rack) Rubber Boot (Ball Stud)

68 - 64 -

69 STEERING SHAFT Item Part Number Nomenclature Q'ty Req Remarks Steering Wheel 1 Includes Horn Button Screw Stop Plate (Steering Wheel) Contact (Steering Wheel) Spring (Steering Wheel) Nut (12) Spring Washer Washer (12.5) Contact Plate (Horn Button) Washer (Cancel Cam) Cancel Cam Upper Cover (Steering Shaft) Washer Lock Washer Screw Spring Washer Washer Turn Signal & Dimmer Switch Steering Shaft Bracket Rubber Bearing (Steering Shaft) Lower Cover (Steering Shaft) Cotter Pin Castle Nut (8) Earth Coard (Horn) Plate (Steering Shaft) Rubber Coupling (Steering Shaft) Bolt (8 x 20)

70 - 66 -

71 GEAR CHANGE EQUIPMENT Item Part Number Nomenclature Q'ty Req Remarks Gear Change Lever 1 Includes Knob (Gear Change Lever) Boot (Gear Change Lever) Stopper (Gear Change Lever) Holder (Gear Change Lever) Spring (Gear Change Lever) Bushing B (Gear Change Lever) Nut Spring Washer Washer Rubber Bushing (Gear Change Rod) Screw Spring Washer Washer Cotter Pin Castle Nut Washer Spring A (Gear Change) Washer Bushing A (Gear Change Rod) Gear Change Rod Set Spring

72 - 68 -

73 BRAKE & CLUTCH PEDAL (LEFT HAND DRIVE) Item Part Number Nomenclature Q'ty Req Remarks Pedal Cover Bolt Bracket (Brake Pedal) Stopper (Clutch Pedal) Washer Spring Washer Bolt Lever (Clutch Pedal Shaft) Nut Spring Washer Washer Stopper (Clutch Pedal) Bolt Lock Nut Bolt Grease Nipple Return Spring (Pedal) Brake Pedal 1 Includes Key (Clutch Pedal Shaft) Clutch Pedal Shaft Clutch Pedal Bolt

74 - 70 -

75 MASTER CYLINDER Item Part Number Nomenclature Q'ty Req Remarks Master Cylinder 1 Includes Nipple (Master Cylinder) Valve Seat (Master Cylinder) Check Valve (Master Cylinder) Spring (Master Cylinder) Primary Cup (Master Cylinder) Cotter Pin Nut (10) Pin (Master Cylinder) Connector (Piston Rod) Nut Push Rod (Master Cylinder) Piston (Master Cylinder) Stop Washer (Master Cylinder) Stop Ring (Master Cylinder) Boot (Master Cylinder) Union Bolt (Master Cylinder) Gasket (Master Cylinder) Master Cylinder Repair Kit (A) 1 Consists of 6, Master Cylinder Repair Kit (B) 1 Consists of 3-6,

76 - 72 -

77 CLUTCH CONTROL SYSTEM Item Part Number Nomenclature Q'ty Req Remarks Bolt Spring (Clutch Cable) Washer Bolt Spring Washer Clutch Lever Return Spring (Clutch Lever) Key (Clutch Lever) Wing Nut (Clutch Cable) Pin (Clutch Lever) Bracket (Clutch Cable) Clip Spring Washer Bolt Clamp (Clutch Cable) Return Spring (Clutch Pedal) Holder (Bushing) Pin Cotter Pin Clamp (Clutch Cable) Bolt Clutch Cable 1 Includes 2, 3, 9, Clamp (Clutch Cable) Bolt

78 - 74 -

79 BRAKE PIPING Item Part Number Nomenclature Q'ty Req Brake Hose (Front) Brake Pipe (Front - Rear Connector) Brake Pipe (Rear Right) Brake Hose (Rear) Brake Pipe (Rear Left) Brake Pipe (Front Left) Brake Pipe (Front Right) Tube (Brake Oil Tank) Connector (Brake Pipe - Front) Nut (Brake Hose) Spring Washer Connector (Brake Pipe - Rear) Bolt Spring Washer Brake Oil Tank Grommet 1 Remarks

80 - 76 -

81 HAND BRAKE SYSTEM Item Part Number Nomenclature Q'ty Req Remarks Bolt Spring Washer Clip (Hand Brake Cable) Nut Hand Brake Cable (Right) 1 Includes Grease Nipple Hand Brake Cable (Left) 1 Includes 6 & Bolt Cover (Cable End) Bolt Cotter Pin Pin (Hand Brake Lever) Pin Arm (Hand Brake Lever) Hand Brake Rod Washer Clamp (Hand Brake Rod) Hand Brake Lever 1 Includes Washer (Hand Brake Lever) Ratchet (Hand Brake Lever) Collar (Hand Brake Lever) Push Button (Hand Brake Lever) Spring (Hook) Hook (Hand Brake Lever) Screw

82 - 78 -

83 ACCELERATOR, CHOKE & HEATER CONTROL SYSTEM Item Part Number Nomenclature Q'ty Req Remarks Bolt (Cone Point) Spring Washer Lock Washer (Counter Sunk Tooth) Screw (Oval Head) Lever Assy (Choke, Heater, Fuel) Accelerator Cable 1 Includes Choke Cable Cotter Pin Washer Packing (Lever Cover) Accelerator Pedal Cable Support Spring Washer Nut Bracket Bolt Screw End (Accelerator Cable) Spacer Washer Bolt

84 - 80 -

85 ENGINE MOUNTING Item Part Number Nomenclature Q'ty Req Bolt Muffler Spring Washer Nut Clamp Ring Bolt Bolt Nut Pre-Chamber Washer Spring Washer Nut (10) Bracket (Front Mounting - Left) Bracket (Front Mounting - Right) Nut Bracket (Front Mounting) Bolt Cushion Rubber (Front Mounting) Spacer (Protector) Protector (Differential Case) Spring Washer Bolt Washer Cushion Rubber (Rear Mounting) Bracket (Rear Mounting) 1 Remarks

86 - 82 -

87 FUEL SYSTEM Item Part Number Nomenclature Q'ty Req Remarks Fuel Meter Unit Packing (Fuel Meter Unit) Screw Earth Cord (Fuel Meter Unit) Spacer (Fuel Tank) Bolt Washer (Fuel Tank Band) Pipe (Air Vent) Pipe (Air Vent) Cap (Fuel Tank) Packing (Fuel Cap) Grommet Fuel Tank Spacer (Fuel Tank) Packing (Fuel Strainer) Spacer (Fuel Tank) Pin Cotter Pin Band (Fuel Tank) Fuel Strainer 1 Includes Cup (Fuel Strainer) Packing (Cup) Filter Element Pipe (Strainer) Controller (Strainer) Valve (Strainer) 1 Now available from Ed (Club) - Reproduction Fuel Pipe (Fuel Strainer) Filter (Fuel Strainer) Nut (Fuel Strainer) Packing (Nut) Spring Washer Screw (Pan Head)

88 - 84 -

89 OIL TANK Item Part Number Nomenclature Q'ty Req Remarks Oil Tank Assy 1 Includes 3-9, 10, 14, Screw Oil Lever Unit 1 Includes Packing (Oil Level Unit) Clip Pipe (Oil Tank) Nut Screw Pipe Cap (Oil Tank) Packing Filter (Oil Tank) Saucer (Oil Tank) Band (Oil Tank) Washer Spring Washer Nut Nut Clip

90 - 86 -

91 BODY PARTS Item Part Number Nomenclature Q'ty Req Front Fender (Right) Front Fender (Left) Bolt Spring Washer Washer (5) Lock Washer Screw Washer Nut Rear Skirt Nut Spring Washer Washer Bolt Bolt Bolt Spring Washer Nut Cross Member (Engine Support) Diagonal Member Washer Spring Washer Bolt Washer (6.7) Spring Washer Bolt Under Cover (Engine Room) Front Skirt Nut Spring Washer Washer Bolt Washer Screw (Round Head) Plate 1 Remarks

92 - 88 -

93 FRONT HOOD Item Part Number Nomenclature Q'ty Req Front Hood Bolt Spring Washer Washer Bumper (Front Hood) Washer (5) Stay (Front Hood) Washer Bolt 1 Remarks

94 - 90 -

95 ENGINE HOOD Item Part Number Nomenclature Q'ty Req Stay (Engine Hood) Hinge (Engine Hood Stay) Nut Spring Washer Screw Cotter Pin Stopper (Engine Hood) Screw Washer Washer Spring Washer Nut Rubber Washer (Hinge) Lock Washer Screw Hinge (Engine Hood - Right) Nut Spring Washer Washer Screw Cover Rubber Plug Engine Hood Bumper (Engine Hood) Hinge (Engine Hood - Left) 1 Remarks

96 - 92 -

97 BODY CONSTRUCTION Item Part Number Nomenclature Q'ty Req Remarks Cowl Panel Front Rail (Outer) Front Rail (Inner) Rear Quarter Panel (Outer Right) Rear Quarter Panel (Outer Left) Rear Fender Apron & Frame (Right) Rear Fender Apron & Frame (Left) Rear Quarter Panel (Inner Right) Rear Quarter Panel (Inner Left) Rear Bulkhead 1 Includes Bracket (Fuel Tank Band) Screw Spring Washer Rear Rail Rear Panel Floor & Tunnel Instrument Panel Toe Board (Left) Front Bulkhead Toe Board (Right) Duct (Front Tire Apron - Right) Duct (Front Tire Apron - Left) Tire Apron & Side Sill (Outer Right) Tire Apron & Side Sill (Outer Left) Front Pillar (Inner Right) Front Pillar (Inner Left) Side Rail (Inner Right) Side Rail (Inner Left) Front Pillar (Outer Right) Front Pillar (Outer Left)

98 - 94 -

99 INSTRUMENT PANEL FITTING Item Part Number Nomenclature Q'ty Req Remarks Pad (Instrument Panel) 1 Includes Moulding (Instrument Panel - Right) Clip (Instrument Panel) Moulding (Instrument Panel - Center) Moulding (Instrument Panel - Left) Washer Spring Washer Nut Box (Instrument Panel) Screw (Pan Head) Tapping Screw (Truss Head) Nut Spring Washer Washer Screw Assist Rail