DVI/HDMI, VGA, 3G-SDI, HD-SDI, SDI, CVBS

Transcription

1 Thunder Link is a family of small form factor modules for formatting and converting generic digital video streams to standard compliant formats. Different interface standards are supported from the transmitter side including DVI/HDMI, VGA, 3G-SDI, HD-SDI, SDI, CVBS and USB. Supported physical media are copper and fibre cables. The TL6830_Demo USB3.0 HD video streamer module connects to the parallel CMOS interface of Sony s FCB-MA130. Selection of the desired video output format of this USB3.0 FCB-MA130 camera demo solution is done by using a simple character based terminal program on the host computer. TL6830_Demo - Features + Tiny, easy to use HDTV USB 3.0 compliant video capture solution for new 13 Megapixel Sony FCB-MA130 + Up to 1080p30 uncompressed full motion HDTV video data, 4:2:2 YUV format + The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer + Selection of video output format by simple terminal program based control (RS232 based) + Parallel CMOS video input from camera + Full USB bus powered operation + Power supply voltage and reset control for camera is generated onboard Note: FCB-MA130 is available from Sony and its distributors. It is not part of the Aivion TL6830_Demo package. Please contact with [email protected] for further information. Block Diagram TL6830_Demo Supports New FCB-MA130 Preliminary Data Preliminary Data Aug. 22nd, Provided data is valid for B and C revision boards. 1

2 Supported Cameras Model FCB-MA130 Comment Supported Video and Still Capture Modes The TL6830_Demo supports all full motion video standards and some still capture modes of the FCB-MA130. For details, please refer to the following table and the FCB-MA130 data sheet provided by Sony. Video mode support 25Hz, 30 Hz 25Hz, 30Hz 25Hz, 30Hz 25Hz, 30Hz 25Hz, 30Hz 25Hz, 30Hz Still capture mode support 4192x3104 (output rate 5fps) 2592x1944 (output rate 5fps) 1920x1080 (output rate 5fps) 640x480 (output rate 15fps) Host (PC) - Device Communication TL6830_Demo operates always as USB device which sends UVC compliant video data to a host PC. The host communicates with the TL6830_Demo via a RS232 serial communication channel. Connecting the TL6830_Demo to the Host PC (refer to application note AN_TL6830_Demo_130811_b for further information) Operating System Support TL6830_Demo can be operated with all operating systems which fully support USB UVC type data and communication. Currently, Microsoft Windows 7 (32 and 64bit) and Windows 8 operating systems are supported as reference. Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with e.g. Microsoft Windows 7 <usbvideo.sys> operating systems. Manual driver installation is not necessary. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer, Debut or similar. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. On MS Windows systems, access to and display of video data is based on MS DirectShow. For further information please refer to Microsoft Windows SDK documentation. Controlling TL6830_Demo from the Host PC via RS232 UART TL6830_Demo provides a RS323 UART interface. Camera mode selection is done by using simpe character based terminal software (Hyperterminal, Terra Term or similar). As FCB-MA130 control is based on I2C bus commands, TL6830_Demo translates received terminal commands into I2C bus command sequences. Communication speed is fixed to 9600bit/s. COM port settings are (8N1). [email protected] 2

3 Board Connector Layout PCB top side: USB3 microb connector FCB-MA130 connector PCB bottom side: TRIG STRB RS232 Image shows PCB bottom side (red arrows mark pin 1 location) Onboard Mode Switches Dual slide switch: The dual slide Switch 1 is not used for FCB-MA130 operation. SW 1-1: Keep OFF: SW 1-2: Keep OFF J2: Do not connect J3: Do not connect J4, J5, J7: Do not connect J10: FCB-MA130 outputs (not for rev.b boards) Pin 3: GND Pin 4: TRIG (3.3V, 8mA) Pin 5: STRB (3.3V, 8mA) Quad slide switch: SW 2-3: OFF: Camera control over USB (USB UART, default) ON: Camera control over RS232 UART (connector J9) Set SW 2-3 to ON for FCB-MA130 operation Switches 2-1, 2-2 and 2-4 must be kept in OFF position. J9: RS232 UART connector Pins 1 to 7: do not connect Pin 8: GND Pin 9: RXD (host to TL6830_Demo) Pin 10: TXD (TL6830_Demo to host) [email protected] 3

4 Board Mechanical Flex Cable Connector Inserting the flex cable: FCB-MA130 Connector Image shows PCB top side FCB-MA130 Flex Cable Connect FCB-MA130 side connect TL6830_Demo board side connect Supplied cables with TL6830_Demo: + 4 (10.16cm) flex cable (0.3mm pitch) + Cables for RS232 connection with host + 2m USB3.0 micro B cable [email protected] 4

5 TL6830_Demo Setup FG-AIVO18-10/2013 Subject to technical change without notice. No liability is accepted for errors which may be contained in this document.. IMAGING IS OUR PASSION UNITED KINGDOM FRANCE THE NETHERLANDS IRELAND BELGIUM. LUXEMBOURG Phone: Phone: Phone: [email protected] 5 [email protected] [email protected] [email protected]