MTX 75 Transmission - Dismantle and Assemble ( )
|
|
|
- Jonathan Hopkins
- 7 years ago
- Views:
Transcription
1 «Escort 1991/1996 Table of Contents» «Group 16: Manual Transmission and Clutch» «Section 16-03: MTX 75 Manual Transmission and Clutch» «REMOVAL AND INSTALLATION» MTX 75 Transmission - Dismantle and Assemble ( ) (transmission removed) Special Tools Installer, bearing cups Installer, selector shaft oil seal Installer, bearing rings A-01Thrust pad Installer, differential bearing Installer, bearing rings Preload gauge Adaptor Remover, bearing rings ARemover, taper roller bearing (basic tool) Slide hammer Installer, differential oil seal
2 15-073Socket Remover, bearing rings Remover/installer, selector shaft oil seal Mounting plate, transmission Measuring fixture, end float output shaft Collet for A Collet for A Collet for A Pressure plate, gear wheel removal Remover, driveshaft oil seal Adaptor for Adaptor for Valve spring compressor BMounting bracket, transmission ARemover/installer, selector shaft ball sleeves Proprietary Tools ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Magnetic fixture ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Dial gauge ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Hot air fan ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ Workshop Equipment
3 ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Press ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ Materials ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø High-temperature grease ESD-M1C220-A ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Sealer WSK-M2G348-A5 ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Transmission fluid (ATF) ESD-M2C186-A ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Freezing spray ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ Measuring and Adjusting Shims ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Input Shaft Output Shaft Differential ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Measuring shim in mm 1,00 1,00 1,10 ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Adjustment shim availability (mm) 1,15-1,71 1,31-1,91 1, ,20 ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Transmission - Dismantle µ 1. Detach the clutch release lever. 1 Undo the bolt and pull off the lever. 2 Withdraw the gaiter and the bearing bush from above. µ 2. Fit Special Tools.
4 µ 3. Remove the selector mechanism. Put the transmission in neutral. Undo the six bolts. Remove the complete selector mechanism assembly. µ 4. Remove the thrust bearing and the release shaft. µ 5. Remove the guide sleeve. 1 Undo the three bolts. 2 Twist the guide sleeve and prise off.
5 µ 6. Remove the driveshaft oil seals with the Special Tool. µ 7. Detach the speedometer drive pinion. 1 Pull out the roll pin. 2 Pull out of drive pinion. Detach the selector shaft oil seal. µ 8. Pull off the oil seal using the special tool.
6 Do not drive out the dowel pins. µ 9. Remove the transmission housing bolts. CAUTION: Do not damage the transmission housing. µ 10. Separate the transmission housing halves 1 Use a support. 2 Separate the housing sections using two levers positioned opposite each other. µ 11. Remove the differential.
7 1 Lift out the complete differential assembly. 2 Take out the magnetic disc. µ 12. Remove the first/second gear selector rods and selector fork. 1 Remove the selector rods. 2 Remove the first/second gear selector fork. µ 13. Remove the first/second gear selector forks. 1 Swivel the fifth/reverse gear selector fork to one side. 2 Turn the third/fourth gear selector fork and remove it. Remove the fifth/reverse gear selector fork. µ 14. Remove the reverse gear idler.
8 1 Detach the circlip. Tilt the input and output shafts to the side. 2 Remove the reverse gear idler by pulling it upwards (see following step for removal sequence). µ 15. Removal sequence for removing the reverse gear idler. 1 Circlip 2 Upper thrust washer 3 Reverse gear idler 4 Needle roller bearing 5 Lower thrust washer µ 16. Remove the input and output shafts. Lift the input and output shafts together out of the transmission housing. Take out the mounting block and reverse idler gear together with the needle roller bearing and thrust washers.
9 µ 17. Remove the selector shaft. 1 Undo the ball socket and take off the selector shaft. 2 Pull off the selector shaft. µ 18. Remove the selector shaft ball sleeves. µ 19. Remove the inner selector shaft bearing bush.
10 Remove the bearing rings. Fit the special tool in the transmission recesses. µ 20. Take off the differential bearing ring. Fit the special tool in the transmission recesses. µ 21. Remove the bearings rings from the input and output shafts. Fit the special tool in the transmission recesses.
11 µ 22. Remove the differential and the bearing rings. From the input shaft From the differential Fit the special tool in the transmission recesses. µ 23. Remove the input shaft bearing ring and the shim. Only carry out if there is damage or leaks. µ 24. Remove the reverse gear idler shaft.
12 See previous step. µ 25. Drive out the reverse gear idler shaft with a block of hardwood. Dismantle the differential. µ 26. Pull the taper roller bearing off the differential. 1 Insert the thrust pad. 2 Pull off the taper roller bearing. Detach the speedometer worm gear. µ 27. Detach the crown wheel. Use a copper hammer. Unscrew the retaining bolts and separate the crown wheel from the differential cage by tapping lightly. 28. General note. From model year '95 a double synchroniser is installed for 1st, 2nd and 3rd gears. The layout and assembly of the single synchroniser for third gear is identical to that for fourth gear. The steps described below refer to the double synchroniser. Refer to the Technical Data table for renewal of synchroniser parts.
13 CAUTION: The inner synchroniser ring and the synchroniser cone must be handled with great care. The layout and assembly of the single synchroniser for 3rd gear is identical to that for 4th gear. The steps described below refer to the double synchroniser. Refer to the Technical Data table for renewal of synchroniser parts. Layout of the input shaft ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Description 1 Taper roller bearing on the clutch side. 2 Input shaft 3 Needle roller bearing - third gear wheel 4 3rd gear wheel 5 3rd gear inner synchroniser ring 6 3rd gear synchroniser cone 7 3rd gear outer synchroniser ring 8 3rd/4th gear synchroniser assembly 9 Circlip
14 10 4th gear synchroniser ring 11 Needle roller bearing for 4th gear 12 4th gear wheel 13 5th gear wheel 14 Circlip 15 Taper roller bearing on the transmission side ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ Dismantle input shaft Taper roller bearing and fifth gear wheel can also be pressed off together (see following step). µ 29. Pull off the taper roller bearing on the transmission side. µ 30. Press off the fifth gear wheel together with the taper roller bearing. 1 Move the circlip upwards out of the annular groove up to the taper roller bearing. 2 Press off the gear wheel together with the circlip and the taper roller bearing.
15 µ 31. Detach the fourth gear wheel together with needle roller bearing and synchroniser ring. 1 Gear wheel 2 Needle roller bearing 3 Synchroniser ring µ 32. Detach the 3rd/4th gear synchroniser assembly. 1 Circlip 2 Gear synchroniser CAUTION: Carefully pull the selector ring off the gear synchroniser hub; the detent balls are spring-tensioned.
16 Mark the installation location of the selector ring. µ 33. Dismantle the gear synchroniser. 1 Selector ring 2 Gear synchroniser hub 3 Compression spring 4 Blocker bar 5 Detent ball µ 34. Detach third gear wheel together with the double synchroniser. 1 Outer synchroniser ring 2 Synchroniser cone 3 Inner synchroniser ring 4 Gear wheel 5 Needle roller bearing µ 35. Pull the taper roller bearing on the clutch side off the input shaft. 36. General note. From model year '95 a double synchroniser is installed for 1st, 2nd and 3rd gears. The layout and assembly of the single synchroniser for third gear is identical to that for fourth gear. The steps described below refer to the double synchroniser. Refer to the Technical Data table for renewal of synchroniser parts.
17 CAUTION: The inner synchroniser ring and the synchroniser cone must be handled with great care. The layout and assembly of the single synchroniser for 3rd gear is identical to that for 4th gear. The steps described below refer to the double synchroniser. Refer to the Technical Data table for renewal of synchroniser parts. Layout of output shaft ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Description 1 3rd gear wheel 2 4th gear wheel 3 4th gear needle roller bearing 4 5th gear wheel 5 5th gear synchroniser ring 6 Fifth/reverse gear synchroniser, complete 7 Circlip 8 Reverse synchroniser ring
18 9 Reverse gear needle roller bearing 10 Reverse gearwheel 11 Taper roller bearing on the transmission side. ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ Dismantle output shaft Taper roller bearing and reverse gear wheel can also be pressed off together. µ 37. Pull off the taper roller bearing on the transmission side. µ 38. Detach the reverse gear wheel. 1 Gear wheel 2 Needle roller bearing 3 Synchroniser ring
19 µ 39. Detach the fifth/reverse gear synchroniser, complete. 1 Circlip 2 Gear synchroniser µ 40. Detach the fifth gear wheel together with the synchroniser ring and the needle roller bearing. 1 Synchroniser ring 2 Gear wheel 3 Needle roller bearing
20 Layout of output shaft ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Description 1 Output shaft 2 2nd gear needle roller bearing 3 2nd gear wheel 4 2nd gear inner synchroniser ring
21 5 2nd gear synchroniser cone 6 2nd gear outer synchroniser ring 7 Gear synchroniser assembly (1st/2nd gear) 8 Circlip 9 1st gear outer synchroniser ring 10 1st gear synchroniser cone 11 1st gear inner synchroniser ring 12 1st gear needle roller bearing 13 1st gear wheel 14 Output pinion 15 Circlip 16 Taper roller bearing ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ µ 41. Pull off the taper roller bearing on the clutch side. CAUTION:
22 Mark the output pinion for re-assembly. The output shaft and output pinion are paired and can be renewed together. µ 42. Press the output pinion and the first gear wheel off together. 1 Circlip 2 Pinion with first gear wheel. µ 43. Detach the double synchroniser and the needle roller bearing together. 1 Needle roller bearing 2 Inner synchroniser ring 3 Synchroniser cone 4 Outer synchroniser ring µ 44. Remove the 1st/2nd gear synchroniser, complete. 1 Circlip 2 Gear synchroniser
23 µ 45. Detach the second gear wheel. 1 Outer synchroniser ring 2 Synchroniser cone 3 Inner synchroniser ring 4 Gear wheel 5 Needle roller bearing Mark the installation position of the selector ring. µ 46. Dismantle the gear synchroniser. Assemble CAUTION: Carefully pull the selector ring off the gear synchroniser hub; the detent balls are spring-tensioned. 1 Selector ring 2 Gear synchroniser hub 3 Compression spring 4 Blocker bar 5 Detent ball 47. Carefully clean and check all parts before reassembly.
24 CAUTION: Immerse the double synchronisers transmission fluid (ESD-M2C186-A) and lubricate all moving parts. µ 48. Install the selector shaft ball sleeves. 1 Insert the inner ball sleeve first. 2 Drive in the ball sleeves using the special tool. µ 49. Insert the inner selector shaft bearing sleeve. µ 50. Install the selector shaft. 1 Install the selector shaft.
25 2 Locate the ball socket in position and tighten. µ 51. Install the reverse gear idler shaft. 1 Apply sealer to the mating face of the reverse gear idler shaft. 2 Locate the reverse gear idler shaft in position with the locating bolt and drive in. 3 Remove the locating bolt and screw in the original bolts. CAUTION: The pressure applied must not exceed 15 kn. µ 52. Install the bearing rings on the transmission housing side. Warm the housing locally with a hot-air blower to about 80ºC. Cool the bearing rings with a refrigerant spray and insert. Install the bearing rings using the press: Input shaft using Output shaft using Differential using Shim of required thickness: Input shaft: 1,00 mm Output shaft: 1,00 mm Differential: 1,10 mm
26 µ 54. Install the measuring shims and bearing rings from the clutch side of the transmission housing half. Warm the housing locally to about 80ºC. Cool the bearing rings with refrigerant spray. 1 Insert the shims of the required thickness. 2 Insert the bearing rings. CAUTION: The pressure applied must not exceed 15 kn. Install using the press, do not drive it in. Bearing rings from: Input shaft using Output shaft using Differential using Assemble differential Do not lubricate taper roller bearings that are to be re-used. New taper roller bearings can be installed untreated. Carefully clean and check all parts and coat with transmission fluid before assembly. µ 55. Fit the crown wheel to the differential. Tighten the crown wheel evenly, working diagonally.
27 The speedometer worm gear or the sensor ring of the vehicle speed sensor must engage in the recess on the housing. µ 56. Press on the taper roller bearing. 1 Install the speedometer worm gear. 2 Press on the taper roller bearing using the press and the Special Tool. CAUTION: Do not use the taper roller bearing as a support. µ 57. Install the taper roller bearing (on the side of the crown wheel). Support the differential below the crown wheel. Press on the taper roller bearing with the special tool. Assemble input shaft Do not oil the taper roller bearing which is being reassembled. New taper roller bearings can be assembled unoiled. 58. Carefully clean and check all parts before reassembly. Coat all running parts with transmission fluid (ESD-M2C186-A). From model year '95 a double synchroniser is installed for 1st, 2nd and 3rd gears.
28 CAUTION: The inner synchroniser ring and the synchroniser cone must be handled with great care. CAUTION: Before installing the double synchroniser unit immerse it in transmission fluid (ESD-M2C186-A). The layout and assembly of the single synchroniser for 3rd gear is identical to that for 4th gear. The steps described below refer to the double synchroniser. Refer to the Technical Data table for renewal of synchroniser parts. Layout of input shaft ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Description 1 Taper roller bearing 2 Input shaft 3 3rd gear wheel needle roller bearing 4 3rd gear wheel 5 3rd inner synchroniser ring 6 3rd gear synchroniser cone
29 7 3rd gear outer synchroniser ring 8 3rd/4th gear synchroniser assembly 9 Circlip 10 4th gear synchroniser ring 11 4th gear needle roller bearing 12 4th gear wheel 13 Fifth gear wheel 14 Circlip 15 Taper roller bearing ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ µ 59. Press on the taper roller bearing on the clutch side. Press on the taper roller bearing using a suitable tube. See previous step. µ 60. Assemble the third gear wheel. 1 Needle roller bearing
30 2 3rd gear wheel 3 Inner synchroniser ring 4 Synchroniser cone 5 Outer synchroniser ring µ 61. Assemble the 3rd/4th gear synchroniser. 1 Insert the compression springs. 2 Insert the blocker bar, together with the detent balls, next to the spring. 3 Align the selector ring correctly and push it on. Install the synchroniser hub with the large collar facing out and the ring groove facing the small collar. µ 62. Installation position of the third/fourth gear synchroniser.
31 µ 63. Install the third/fourth gear synchroniser. Installation position (see previous step). 1 Install the gear synchroniser assembly. 2 Fit a new circlip. µ 64. Fit the fourth gear wheel. 1 Synchroniser ring 2 Needle roller bearing 3 4th gear wheel µ 65. Press on the fifth gear wheel. Press on the fifth gear wheel using a suitable tube and press. Fit a new circlip.
32 µ 66. Press on the taper roller bearings on the transmission and clutch sides (taper roller bearing on the transmission side is shown). Press the taper roller bearing on using a suitable tube. Assemble output shaft Do not lubricate the taper roller bearings which are being reassembled. New taper roller bearings can be installed unoiled. 67. Carefully clean and check all components and coat with transmission fluid (ESD-M2C186-A) before assembly. From model year '95 a double synchroniser is installed for 1st, 2nd and 3rd gears. CAUTION: The inner synchroniser ring and the synchroniser cone must be handled with great care. CAUTION: Before installing the double synchroniser unit immerse it in transmission fluid (ESD-M2C186-A). The layout and assembly of the single synchroniser for 3rd gear is identical to that for 4th gear. The steps described below refer to the double synchroniser. Refer to the Technical Data table for renewal of synchroniser parts.
33 Layout of the output shaft ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Description 1 Output shaft 2 2nd gear needle roller bearing 3 2nd gear wheel 4 2nd gear inner synchroniser ring
34 5 2nd gear synchroniser cone 6 2nd gear outer synchroniser ring 7 1st/2nd gear synchroniser assembly 8 Circlip 9 1st gear outer synchroniser ring 10 1st gear synchroniser cone 11 1st gear inner synchroniser ring 12 1st gear needle roller bearing 13 1st gear wheel 14 Output pinion 15 Circlip 16 Taper roller bearing ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ See the following step. µ 68. Assemble the second gear wheel. 1 Needle roller bearing 2 2nd gear wheel 3 Inner synchroniser ring 4 Synchroniser cone 5 Outer synchroniser ring
35 Mark the installation position µ 69. Assemble the 1st/2nd gear synchroniser. 1 Insert the compression springs. 2 Fit the blocker bar and the gear synchroniser hub ball detents next to the spring. 3 Align the selector ring correctly and push it on. The small collar on the gear synchroniser hub must point outwards. µ 70. Installation position of the first/second gear synchroniser.
36 Installation position (see previous step) µ 71. Assemble the 1st/2nd gear synchroniser. 1 Install the gear synchroniser assembly. 2 Fit a new circlip. See previous step. µ 72. Assemble first gear wheel with double synchroniser. 1 Outer synchroniser ring 2 Synchroniser cone 3 Inner synchroniser ring 4 1st gear wheel 5 Needle roller bearing CAUTION: The output pinion can only be placed on the splines in one position. µ 73. Press on the output pinion. 1 Press on the output pinion using a suitable tube and press. 2 Fit a new circlip. Fit the output pinion with the mark facing upwards.
37 µ 74. Press on the taper roller bearing. Press on the taper roller bearing using a suitable tube and press. Layout of the output shaft ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Description 1 3rd gear wheel 2 3rd gear wheel 3 5th gear wheel 4 5th gear wheel
38 5 5th gear synchroniser ring 6 Gear synchroniser, complete - (fifth/reverse gear) 7 Circlip 8 Synchroniser ring - reverse gear 9 Needle roller bearing - reverse gear 10 Reverse gearwheel 11 Taper roller bearing ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ µ 75. Fit the fifth gear wheel together with the synchroniser ring and needle roller bearing. 1 Needle roller bearing 2 5th gear wheel 3 Synchroniser ring Mark the installation position µ 76. Assemble the fifth/reverse gear synchroniser. 1 Insert the compression springs. 2 Fit the blocker bar and the detent balls next to the spring. 3 Align the selector ring correctly and push it on.
39 Install the gear synchroniser hub with the small collar and the ring groove pointing outwards. µ 77. Installation position of gear synchroniser. Install the gear synchroniser hub with the small collar and the ring groove pointing outwards. µ 78. Fit the fifth/reverse gear synchroniser. 1 Install the gear synchroniser assembly. 2 Attach a new circlip. µ 79. Assemble the reverse gear wheel.
40 1 Synchroniser ring 2 Needle roller bearing 3 Reverse gearwheel µ 80. Press on the taper roller bearing. Press on the taper roller bearing using a suitable tube and press. Measure the shims. Do not lubricate taper roller bearings that are to be re-used. Fit new taper roller bearings untreated. µ 81. Insert the input and output shafts into the transmission housing. Engage 4th gear. Put the input and output shafts together and insert them in the transmission housing.
41 Do not lubricate taper roller bearings that are to be re-used. Fit new taper roller bearings untreated. µ 82. Install the differential. The mating face must be scrupulously clean. µ 83. Fit the housing sections on the clutch side. Fit the special tool and the longer bolt. µ 84. Assemble the transmission housing sections on the clutch side. Tighten the 16 flange bolts evenly.
42 µ 85. Attach the special tool. Fit the measuring bar to the 4th gear wheel. µ 86. Prepare the input shaft for measurement. Turn the input shaft back and forth about 20 times so that the bearings settle. µ 87. Fit the dial gauge. 1 Fit a steel mounting plate (eg ) to the transmission. 2 Install the magnetic fixture. 3 Set the dial pointer to 0".
43 µ 88. Measure the input shaft end float. Carry out the measurement preparations and the measurement three times and calculate the average value. 1 Raise the input shaft using the lever. 2 Make a note of the result (eg 0,22 mm). For example: 0,22 mm + 0,23 mm + 0,21 mm divided by three = 0,22 mm. µ 89. Prepare the output shaft for measurement. Turn the input shaft back and forth about 20 times so that the bearings settle. µ 90. Prepare the output shaft for measurement.
44 Fit the dial gauge. Set the dial gauge to 0". µ 91. Measure the output shaft end float. Carry out the measurement preparations and the measurement three times and calculate the average value. Raise the output shaft using the lever and make a note of the result, eg, 0,32 mm. For example: 0,32 mm + 0,34 mm + 0,33 mm divided by three = 0,33 mm. µ 92. Prepare the differential for measurement. Turn the input shaft approx. 20 times back and forth and press down the differential at the same time. Fit the dial gauge and set it to 0".
45 Carry out the measurement preparations and the measurement three times and calculate the average value. µ 93. Measure the differential end float. Lift up the differential using the special tool and make a note of the result, eg 0,34 mm For example: 0,34 mm + 0,36 mm + 0,37 mm divided by three = 0,36 mm. Measure the shim thickness to be inserted (mm dimensions) ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Description Input Shaft Output shaft Differential ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Measuring shim in mm 1,00 1,00 1,10 ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Measured end float (mm) + 0,22 + 0,33 + 0,36 ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Dimension for pre-tension (mm) - + 0,13 + 0,33 ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ End float (mm) - 0, ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Required thickness of shim = 1,17 = 1,46 = 1,79 ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Adjustment shim availability (mm) 1,15-1,71 (in 0,01 1,31-1,91 (in 0,02 1,40-2,20 (in 0,05 mm steps) mm steps) mm steps) ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Fit the special tool in the transmission recesses.
46 µ 94. Remove the adjustment shim and the bearing rings. From the input shaft From the differential Fit the special tool in the transmission recesses. µ 95. Remove the input shaft bearing ring and the shim. µ 96. Insert the shims and the bearing rings into the housing section on the clutch side. Warm the housing locally to about 80 degrees Centigrade. Cool the bearing rings with refrigerant spray. 1 Insert the shims of the required thickness. 2 Insert the bearing rings. CAUTION: The pressure applied must not exceed 15 kn. Install using the press, do not drive it in. Bearing rings from the: Input shaft using Output shaft using Differential using
47 µ 97. Install the shims and the bearing rings. 1 Install the shims of the required thickness. 2 Bearing rings for the: Install the input shaft, output shaft and differential as described in the steps. Lubricate the taper roller bearings. µ 98. Install the input and output shafts together. Swivel the input shaft to one side and insert the reverse gear idler (for order of installation, see the following step). µ 99. Order of installation for the reverse gear idler.
48 1 Lower thrust washer. 2 Needle roller bearing 3 Reverse gear idler. 4 Upper thrust washer 5 Circlip µ 100. Fit the selector fork. Put the 4th gear selector ring in neutral. Insert the fifth/reverse gear selector fork and swivel to one side. µ 101. Install the 3rd/4th gear selector fork. Swivel the fifth/reverse gear selector fork back into position.
49 When correctly positioned all the selector rods are at the same height. µ 102. Install the 1st/2nd gear selector fork and rods. µ 103. Install the differential. 1 Install the differential. 2 Install the clean magnetic disc in the slot provided. Fit the selector shaft oil seal. The selector shaft must be clean and free of burrs. µ 104. Fit the selector shaft oil seal. Push the selector shaft inwards. 1 Push the oil seal and the assembly sleeve onto the selector shaft. 2 Drive in the oil seal just up to the stop.
50 µ 105. Remove the assembly sleeve, fit the dust cover. The mating face must be dry. Apply sealer (WSK-M2G348-A5) evenly on the inside of the sealing surface. (The sealant bead should have a constant diameter of about 2 mm.) µ 106. Apply sealer to the mating face. µ 107. Fit the transmission housing sections on the clutch side. The transmission housing must not, under any circumstances, be turned when tightening the bolts. Tighten the 16 flange bolts within 15 minutes, working diagonally.
51 Put the gearshift mechanism in neutral. µ 108. Fit the selector mechanism. Apply sealer evenly to the outer side of the mating face. Fit the selector mechanism and tighten. If the turning torque is too high, all the measurements must be repeated (including the measurement to determine the required shim thickness). µ 109. Measure the turning torque. Engage 4th gear. Measure the turning torque.
52 µ 110. Fit the speedometer worm drive. 1 Install the drive pinion. 2 Drive in the notched pin using a hammer. Fit the differential oil seal. µ 111. Fit the differential oil seals. µ 112. Install the guide sleeve. Fit the guide sleeve with a new O-ring and apply sealer (WSK-U26348-A5).
53 µ 113. Install the release shaft. Coat the bearing points on the release shaft with high-melting point grease. µ 114. Fit the thrust bearing. Coat the guide sleeve and clutch teeth thinly with high-melting point grease. µ 115. Remove the special tools.
54 µ 116. Fit the clutch release lever. 1 Fit the bearing bush and the protective cap. 2 Fit the clutch release lever and tighten the bolts.
ARTICLE BEGINNING APPLICATION IDENTIFICATION DESCRIPTION LUBRICATION & ADJUSTMENT TROUBLE SHOOTING. MANUAL TRANSMISSIONS Saab 5-Speed Transaxle
Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Saab 5-Speed Transaxle APPLICATION TRANSMISSION APPLICATION ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Vehicle Application Transmission
This is the civilian transfer case with the cooling loop only found in the driven gear half of the front case.
INTRODUCTION The Transfer case used in the AMG Hummer is a New Venture Gear, model 242. This case has been in use for the H-1/Hummer since the early 1990 s. There have been modifications to the internal
MANUAL TRANSMISSION CONTENTS ...
22D-0-1 MANUAL TRANSMISSION CONTENTS GENERAL INFORMATION... 22D-0-3 1. SPECIFICATIONS... 22D-1-1 TRANSMISSION MODEL TABLE GENERAL SPECIFICATIONS SERVICE SPECIFICATIONS TORQUE SPECIFICATIONS............
2005 MINI Cooper. 2002-05 MANUAL TRANSMISSIONS On-Vehicle Servicing. Cooper S Getrag 285
2002-05 MANUAL TRANSMISSIONS On-Vehicle Servicing APPLICATION MANUAL TRANSMISSION APPLICATIONS Application Transmission Model Cooper R65 Cooper S Getrag 285 LUBRICATION SERVICE INTERVALS Inspect fluid
Rebuild Instructions for 70001 and 70010 Transmission
Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before
Drive shaft, servicing
Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,
Assembly Instructions for
Assembly Instructions for RA553455S1..Gearbox Assembly MRA-200..Gearbox internal parts kit. (SK-1698...Fork setting fixture) Conversion for Lancer Evolution Table of Contents Section Description Page 1.
MANUAL TRANS OVERHAUL - TYPE 02J Article Text 1999 Volkswagen Golf This file passed thru Volkswagen Technical Site -
MANUAL TRANS OVERHAUL - TYPE 02J Article Text 1999 Volkswagen Golf This file passed thru Volkswagen Technical Site - http://volkswagen.msk.ru ARTICLE BEGINNING 1998-99 MANUAL TRANSMISSIONS Volkswagen/Audi
Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing
34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed Gearshift cable/lever installing Gearshift housing repairing Gearshift lever repairing lever/relay lever, installing Gearshift mechanism
Pallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification
OWNER S MANUAL Model MH1230 Important Safety Instructions Assembly Instructions Parts and Hardware Identification Pallet Jack CAUTION: Read, understand and follow ALL instructions before using this product
STEERING SYSTEM - POWER
STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and
Dismantling and Reassembly Guide
Super X3 Mill Dismantling and Reassembly Guide A picture story book to help you dismantle and reassemble your Sieg Super X3 Mill Arc Euro Trade Ltd. 10 Archdale Street, Syston, Leicester, LE7 1NA. Web:
Aprilia.no. RS 50 96-98 Eng.6M
01 Carburettor - oil pump 02 Drive shaft 03 Head - piston 04 Primary gear shaft 05 Gearbox driven shaft 06 Selector 07 Clutch 08 Clutch cover 09 Right crankcase 10 Left crankcase 11 Ignition unit RS 50
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510
AUTOMATIC TRANSMISSION
23E-0-1 AUTOMATIC TRANSMISSION V5A51 CONTENTS GENERAL INFORMATION... 23E-0-3 1. SPECIFICATIONS... 23E-1-1 TRANSMISSION MODEL TABLE... 23E-1-1 GENERAL SPECIFICATIONS... 23E-1-2 SERVICE SPECIFICATIONS...
2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13)
2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13) Exploded View Special Tools Required Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool 07GAF-SD40100 Bearing driver attachment,
Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997
Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47
Front brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
6-Speed Synchromesh Transmission Service Manual. (FS-6406 Series)
6-Speed Synchromesh Transmission Service Manual (FS-6406 Series) Issue 01/2003 Eaton 6-Speed Synchromesh Transmission Truck Components Operations Europe PO Box 11 Worsley Manchester M28 5GJ England Service
LT230T TRANSFER GEARBOX. Overhaul Manual LT230T. Verdeelbak revisieboek LT230T. Boîte de transfert Manuel de révision LT230T
LT230T TRANSFER GEARBOX Overhaul Manual LT230T Verdeelbak revisieboek LT230T Boîte de transfert Manuel de révision LT230T Verteilergetriebe Überholungsanleitung LT230T Riduttore Manuale di revisione LT230T
3. Loosen 3 x grub screws in the Dec end cap and unscrew the cap and counterweight shaft. NEQ6 Belt Modification Kit.
NEQ6 Belt Modification Kit. Thank you for your purchase. Please read these instructions fully before fitting. Your package should contain 2 off 47 & 2 off 12 tooth aluminium pulleys 2 off belts 6mm wide
Nuffield and Middleweight Leyland Tractor - 11 inch - Double Clutch Overhaul Part 1 - Clutch Removal and Dismantling
Nuffield and Middleweight Leyland Tractor - 11 inch - Double Clutch Overhaul Part 1 - Clutch Removal and Dismantling Due to the many different configurations of cabed and non-cabed tractors this article
DO NOT attempt to repair hub and wheel bearing assembly.
Page 1 of 6 HUB & WHEEL BEARINGS (WITH PULSE VACUUM HUBLOCK) DO NOT attempt to repair hub and wheel bearing assembly. Removal DO NOT remove hub lock assembly by prying on hub lock legs. This can crack
Replacement Spare Parts for FORD TRACTOR
(3650) POWER STEERING HYDRAULIC PUMP GEAR SET (9T.) (866) HYDRAULIC PUMP FRONT DRIVE GEAR (10T.) (C5NN 3A710 A/NUT) STRG. GEAR SHAFT MAIN NUT (C5NN 3A710 A/TUBE) STRG. GEAR SHAFT MAIN NUT TUBE (C5NN 3A710
IMPORTANT SAFETY NOTICE NOTES, CAUTIONS, AND WARNINGS
IMPORTANT SAFETY NOTICE Appropriate service methods and proper repair procedure are essential for the safe, reliable operation of all motor vehicles as well as the personal safety of the individual doing
Planetary Drive Axles
Issued 07-00 $2.50 Planetary Drive Axles Maintenance Manual 9H PRLC 124 W2H PRLC 144 W2H Models PRLC 124 W2H PRLC 144 W2H Service Notes Service This Notes maintenance manual describes the correct service
Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
Slide the new steering column shaft through the steering column from the driver compartment.
Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.
CHAPTER 65 TAIL ROTOR DRIVE SYSTEM. Section Title Page
CHAPTER 65 TAIL ROTOR DRIVE SYSTEM Section Title Page 65-00 Description........................................ 65.1 65-10 Tail Rotor Drive Fan Shaft.............................. 65.1 65-20 Tail Rotor
FRONT SUSPENSION Click on the applicable bookmark to selected the required model year
FRONT SUSPENSION 33A-2 FRONT SUSPENSION General Information GENERAL INFORMATION 33200010105 The front suspension on 2WD vehicles is an independent suspension system having the double wishbone combined
Char-Lynn Spool Valve Hydraulic Motors. Repair Information. W Series Geroler Motors
Char-Lynn Spool Valve Hydraulic Motors Repair Information W Series Geroler Motors with Parking Brake 004 Nut Key Ring, Retaining Bearing Ring, Retaining Ring, Retaining Washer (Thick), Pressure Washer,
TC 170 & TC 170 PD TRANSFER CASE
Automotive Corporation TC 170 & TC 170 PD TRANSFER CASE PARTS MANUAL Fabco Automotive Corporation, Livermore, CA Ph:(925) 454-9500 Fax:(925) 454-9501 1-(800) 967-8838 www.fabcoautomotive.com VII. PARTS
3000, 4000, 4100, 7500, 7700
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the
AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION
AXLE SHAFTS - FRONT 1998 Pontiac Bonneville 1998-99 DRIVE AXLES FWD Axle Shafts - Cars - "C", "G" & "H" Bodies GM Aurora, Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue, Regency, Riviera MODEL IDENTIFICATION
1/29/2008 DR125 / DR150. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55
DR125 / DR150 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55 CYLINDER HEAD ASSY. 1 125-001 883099006937 CYLINDER HEAD COVER 1 1 2 125-002 883099006944 BOLT M6X28 2 3 3 125-003 883099006951
Illustrated Parts List
Spicer Tandem Axles Illustrated Parts List AXIP0085a January 1994 Single Reduction, Dual Range, & Double Reduction Addendum 461, 462, 463, 521, 581 46,000-65,000 lbs Introduction Single Reduction w/wheel
Number Wheeler P/N Description Set Rex P/N Notes 1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8)
1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8) 4 5 600130 Spring Washer (8mm) 4 6 600344 Roll Pin (M6x30) 4 7 600129 Socket Hd Cap Screw (M8x25) 4 8
DANA 30 MANUAL HUB CONVERSION KIT
DANA 30 MANUAL HUB CONVERSION KIT 12194 PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU BEGIN Your safety and the safety of other motorists is very important. Your Jeep is an off road capable vehicle
ADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit)
ADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit) Instruction Sheet P/N: 50-7905 & 50-7906 KIT CONSISTS OF: No. Qty Part No. Description 1. 1 51-7906 TAILHOUSING, DIECAST 2. 1 52-7905 SHAFT, MAIN OUTPUT
Model No: VS4815 1. SAFETY INSTRUCTIONS VS4800 2. INTRODUCTION & APPLICATIONS VS4815 3. CONTENTS. 2.1 Introduction. 2.
Instructions for: Petrol Engine Twin Camshaft Setting / Locking Tool Kit - (incorporating Vanos Alignment) - BMW N42 & N46 Engines Model No: VS4800 Associated kit: Camshaft/Carrier Bracket Remover & Installer
Round Housing with Side Ports
Power Steering Steering Control Unit (SCU) Parts and Repair Information 5 Series Steering Control Units 001 Square Housing with Side Ports Round Housing with Side Ports T E L RP Round Housing with End
Front axle components, overview
just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,
DRIVE AND DRIVEN PULLEY
11 DRIVE AND DRIVEN PULLEY SCHEMATIC DRAWING ------------------------------------------------- 11-1 SERVICE INFORMATION------------------------------------------------ 11-2 TROUBLESHOOTING-----------------------------------------------------
2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure
2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure Derek Guenther 1/28/2015 Rev. Purpose The purpose of this document is to describe the procedure necessary to replace one of the ball nuts
For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com.
For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Information contained in this publication is subject to change at anytime
ARTICLE BEGINNING APPLICATION & LABOR TIMES IDENTIFICATION DESCRIPTION & OPERATION. AUTOMATIC TRANSMISSIONS Volkswagen Type 01M
Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Volkswagen Type 01M Cabrio, Golf, Golf III, GTI Jetta, Jetta III, Passat APPLICATION & LABOR TIMES APPLICATION & LABOR TIMES ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
1/29/2008 DR70. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43
DR70 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43 CYLINDER & CYLINDER HEAD 1 DR70-001 883099044472 CYLINDER 1 1 2 DR70-002 883099044489 GASKET, CYLINDER 1 1 3 DR70-003 883099044496
Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning
Rear wheel brakes, servicing. Стр. 1 из 45. Note:
Volkswagen Touareg - Rear wheel brakes, servicing Стр. 1 из 45 46-2 Rear wheel brakes, servicing Rear brakes, FN 44 brake caliper, servicing Note: After replacing brake pads, depress brake pedal firmly
The Ford Model A Water Pump
The Ford Model A Water Pump George Washington Chapter, Inc. 3903 Old Lee Highway Fairfax, VA 22030 1 Table of Contents Introduction/Specifications.. 3 1. Water Pump Inspection and Removal. 4 a. Removal..
Mercedes 722.3 722.4
96 Mercedes 7. 7. 5 6 7 8 - Clutch K - Brake Band B - Disc Brake B - Wide Planet Pinion 5 - One-Way Clutch F 6 - Clutch K 7 - Brake Band B 8 - Narrow Planet Pinion Int. Band Fwd. Band Rev. Clutch Direct
White Industries Rear Hub Instructions
White Industries Rear Hub Instructions Tool required: 2mm allen/hex wrench, 19mm socket, 20mm socket, and mallet. 1. Loosen the set screws located in the adjusting collar by using a 2mm allen wrench inserted
Rexroth. Spare parts list. Bosch Group. Part No.: R909401762 Designation: VERSTELLPUMPE A4V-125 HD
: R909401762 : VERSTELLPUMPE A4V-125 HD *G* 1 R909400454 ROTARY GROUP L 2 R909414470 HYDRAULIC CONTROL L 3 R909080279 PORT PLATE WITH VALVES L 4 R909400395 INTERNAL GEAR PUMP L 6 R909401736 CONTROL MODULE
STORAGE, INSTALLATION AND MAINTENANCE PROCEDURES
GATE VALVE O.S. & Y 1.0 Periodic Inspections 1.1 The valve stem packing should be inspected at least monthly. If the stem packing shows signs of leakage, simply tighten the adjusting nuts to compress the
Single Reduction Differential Carrier 17X
Maintenance manual no. MM-0700EN Single Reduction Differential Carrier 17X Issue: February 2007 Issue 02/2002 Contents pg. 06 Section 1: Introduction pg. 7 Specification & Data pg. 8 Exploded View pg.
AXLE SHAFTS - FRONT. 1993 Toyota Celica DESCRIPTION REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION. 1993 DRIVE AXLES Toyota FWD Axle Shafts
AXLE SHAFTS - FRONT 1993 Toyota Celica 1993 DRIVE AXLES Toyota FWD Axle Shafts Toyota; Celica DESCRIPTION Axle shafts transfer power from transaxle to driving wheels. All axle shafts consist of a shaft
Spicer Axles & Brakes ABIB-0302
Information Bulletin Bulletin Type: Parts / Service Information Topic: Dana LMS Hub Assembly Procedure Steer and Drive Axles Spicer Axles & Brakes ABIB-0302 Note: Bulletin ABIB-0302 replaces the original
12. REAR WHEEL/BRAKE/SUSPENSION
12 12 12-0 SERVICE INFORMATION... 12-1 REAR BRAKE... 12-5 TROUBLESHOOTING... 12-2 REAR SHOCK ABSORBER... 12-8 REAR WHEEL... 12-3 REAR FORK... 12-9 SERVICE INFORMATION GENERAL INSTRUCTIONS When installing
1/29/2008 DR50. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45
DR50 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR50-001 842645074424 CYLINDER 1 1 2 DR50-002 842645074431
DiscPlus DX195 and DX225 Air Disc Brakes
Revised 11-04 Technical Bulletin Revised 1 Technical 11-04 Bulletin DiscPlus DX195 and DX225 Air Disc Brakes Inspection, Installation and Diagnostics Air Disc Brake Inspection Intervals and Procedures
Engine, disassembling and assembling
13-1 Engine, disassembling and assembling Note: Replace the oil cooler and thoroughly clean the oil passages if you find metal shavings or larger quantities of small metal particles in the engine oil,
Atlas Front Input Change
Atlas Front Input Change The following pages contain instructions for Atlas transfer case front input. Most mechanically inclined individuals can obtain the components from us and perform these retrofits
Eaton Fuller Heavy Duty Transmissions Illustrated Parts List FS-5005C March 2003
Eaton Fuller Heavy Duty Transmissions Illustrated Parts List FS-00C March 00 For the most current information, visit the Roadranger web site at www.roadranger.com Contents How To Use The Illustrated Parts
DR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002
Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008)
Rear Wheel/Brake/Suspension 13. Rear Wheel/Brake/Suspension Service Information 13-1 Troubleshooting 13-2 Rear Wheel 13-3 Rear Cushion 13-4 Rear Swing Arm 13-7 Service Information General Safety If the
DR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002 842645048173 GASKET, CYLINDER 1 1 3 DR90-003
TECHNICAL SERVICE MANUAL
TECHNICAL SERVICE MANUAL HEAVY-DUTY PUMPS SERIES 4195 AND 495 SIZES GG - AL SECTION TSM 144 PAGE 1 of 10 ISSUE D CONTENTS Introduction....................... 1 Safety Information.................... 2
13. REAR WHEEL/BRAKE/SUSPENSION
13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...
Operating Instructions Parts List Manual Scissor Lift Pallet Truck
Operating Instructions Parts List Manual Scissor Lift Pallet Truck Note: Operator MUST read and understand this operating instructions before use this Hand Scissor Lift. Thank you for using this hand scissors
STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER
14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------
Service Manual Rol-Lift
R 2000 Service Manual Rol-Lift Series: T and E Developed by Generic Parts Service This manual is intended for basic service and maintenance of the Rol-Lift pallet jack. The pallet jacks you are servicing
M-4209-8.8 8.8 Ring and Pinion Installation INSTRUCTION SHEET
Please contact the Techline for the most current instruction information (800) FORD788!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna)
Installation Instructions Reverse Gear MAMBA (Monoblock for Cable operated) Read and become familiar with these installation instructions before start. Two Piece for H-D 5 Speed Trans., Cable operated
ASSEMBLY DIAGRAM AND ASSEMBLY REFERENCE ULTIMA OLD SCHOOL 2 EVO & TC BELT DRIVE UNITS
ASSEMBLY DIAGRAM AND ASSEMBLY REFERENCE ULTIMA OLD SCHOOL 2 EVO & TC BELT DRIVE UNITS BELT DRIVE ASSEMBLIES Part# 58-850 2 Old School Belt Drive Assembly - Polished Part# 58-851 2 Old School Belt Drive
CAM-03, Camshaft Assembly Oil Seal Replacement
CAM-03, Camshaft Assembly Oil Seal Replacement Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft Pin Spanner
S&G Model 2937 Group 1 Combination Lock
Installation and Combination Changing Instructions S&G Model 2937 Group 1 Combination Lock NOTE: READ COMPLETE INSTRUCTIONS BEFORE INSTALLATION These instructions should be followed when installing the
DIFFERENTIAL AND DRIVELINE
PL DIFFERENTIAL AND DRIVELINE 3-1 DIFFERENTIAL AND DRIVELINE TABLE OF CONTENTS page DESCRIPTION AND OPERATION FRONT DRIVESHAFTS...1 DIAGNOSIS AND TESTING DRIVESHAFT DIAGNOSIS....2 REMOVAL AND INSTALLATION
BACKPACK SPRAYERS. MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12
BACKPACK SPRAYERS MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12 INTRODUCTION Thank you for purchasing this CLARKE Sprayer, designed for use only with
Number Wheeler P/N Description Set Rex P/N Notes
1 607051 Base 1 A050 2 607052 Motor Cover 1 A052 3 600778 Socket Hd Cap Screw (M8x60) 2 4 607053 Scrap Receiver 1 A053 5 607054 Tank Upper Cover 1 A054 6 607055 Oil Pot 1 A055 7 607056 Strainer 1 A056
Number Wheeler P/N Description Set Rex P/N Notes
1 604041 Base 1 4041 2 604042 Base Cover 1 4042 3 608849 Washer (M5) 2 4 600124 Spring Washer (M5) 2 5 600329 Rd Hd Machine Screw (M5x8) 2 6 604047 Strainer 1 4047 7 600204 Rd Hd Machine Screw (M6x10)
ABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions
4057250/8 IM-P405-16 AB Issue 8 ABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Operation
Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19
Table of Contents Overview 1 Pump Disassembly 2 Control Disassembly / Reassembly 7 Pump Reassembly 13 Adjustment Procedures DR Control 19 Adjustment Procedures DRG Control 20 Adjustment Procedures DFR
Webinar Series. Committee. Disc Brake Wheels Off Inspection and Reline. Presents
1 APTA Bus Webinar Technical Series Maintenance Committee Webinar Series Presents Disc Brake Wheels Off Inspection and Reline January 21, 2015 2 Introduction Welcome to today s webinar in which we will
MUSTANG II IFS COMPLETE PARTS PACKAGE
MUSTANG II IFS COMPLETE PARTS PACKAGE Your Southern Rods & Parts Mustang II IFS Parts Package contains the following items: 1 pr) Upper Control Arms (2023) 1) Upper Arm Bolt Kit (MP-001-A) 1 pr) Lower
BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > GOKART > BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM) BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
1 Important Safety Procedures. Qualified maintenance personnel should read and follow these straightforward instructions.
Installation, Operating and Maintenance Instructions XL Series Actuators Contents Important Safety Procedures Mounting and Operating Instructions Piping Instructions Solenoid Valves on Spring Return Actuators
DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH) DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX
BSA Goldstar Parts - Price List April 2016. 65-1137 Exhaust Lifter Cable 15.00. 65-1163 Exhaust Lifter Cable Holder S/S 9.00
Rocker Boxes 65-1137 Exhaust Lifter Cable 15.00 65-1163 Exhaust Lifter Cable Holder S/S 9.00 2-443 Exhaust Lifter Cable Holder Nut S/S 0.50 65-401 Exhaust Lifter Spindle Felt 2.00 65-387 Exhaust Lifter
SCION tc 2005-2008 COIL OVER SUSPENSION Preparation
SCION tc 2005-2008 COIL OVER SUSPENSION Preparation Part Number: PTR11-21070 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item # Quantity Reqd. Description
HYDRAULIC LIFT TABLE CART 2200-LB.
HYDRAULIC LIFT TABLE CART 2200-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other
Dismantling and Reassembly Guide
C3 Mini-Lathe Dismantling and Reassembly Guide A picture story book to help you dismantle and reassemble your Sieg C3 Mini-Lathe Arc Euro Trade Ltd. 10 Archdale Street, Syston, Leicester, LE7 1NA. Web:
C O N T E N T S 1 ABOUT THIS PARTS LIST... 2 ENGINE GROUP... 3 3 CONTENTS-FRAME GROUP
C O N T E N T S 1 ABOUT THIS PARTS LIST... 2 2 CONTENTS-ENGINE ENGINE GROUP ENGINE GROUP... 3 3 CONTENTS-FRAME GROUP FRAME GROUP... 5 4 ENGINE PARTS LIST... 9 5 FRAME PARTS LIST...37 1 ABOUT THIS PARTS
Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation
Instruction Manual 1052 Size 20 Actuator (F & G) Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Contents Introduction... 1 Scope of manual... 1 Description... 1 Specifications...
ALLDATA Online - 2006 Dodge Truck RAM 2500 Truck 2WD L6-5.9L DSL Turbo VI... Service and Repair
Page 1 of 15 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2006 Dodge Truck RAM 2500 Truck 2WD L6-5.9L DSL Turbo VIN C Conversion
1.8 CRANKSHAFT OIL SEALS
SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the
MOPAR 8.75 REAR DIFFERENTIAL INFORMATION
MOPAR 8.75 REAR DIFFERENTIAL INFORMATION Sure Grip is the performance type of differential that enables both rear tires to turn under power for better launch traction. Sure Grip is the Chrysler name for
Fisher 1061 Pneumatic Piston Rotary Actuator with Style F & G Mounting Adaptations
Instruction Manual 1061 F & G Actuator Fisher 1061 Pneumatic Piston Rotary Actuator with Style F & G Mounting Adaptations Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...
CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6
CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize