MASONRY DRILLING TOOLS

Transcription

1 MASONRY DRILLING TOOLS NOTES PAGE NO. ITEM POINTS TO REMEMBER

2 MASONRY DRILLING INDEX ADAPTERS PLATE CUTTER...3 REBAR CUTTER...4 SDS - QUICK RELEASE...15 TAPER CHUCK...22 CHISELS ASPHALT CUTTER 5"...28 BULL (MOIL) POINT...27 BUSHING TOOL (1 PC TOOL)...28 BUSHING TOOL (2 PC TOOL KIT)...28 BUSHING TOOL HEADS...28 BUSHING TOOL (STEMS)...28 CLAY SPADE 5-1/2"...28 FLAT (COLD) CHISEL...27 GROUND ROD DRIVER...28 MORTAR (SEAM) CHISEL...28 SCALING CHISEL...27 SLOTTING TOOL...28 CUTTERS PLATE...3 REBAR...4 DRILLS (glass cutting)...11 (metal cutting) HARD STEEL...2 UNIVERSAL...1 SCREW EXTRACTOR (left hand)...2 MASONRY DRILL DISPLAYS FAST SPIRAL...9 WIDE SPIRAL...10 MASONRY DRILL SETS FAST SPIRAL...9 SDS...14 UNIVERSAL WIDE SPIRAL...9 MASONRY DRILLS CARPET STUBBY...11 CORE - DIAMOND...6 CORE - PERCUSSION HAMMER...8 EJECTOR KEY...8 PILOT DRILL...8 S...8 CORE - ROTARY...5 PILOT DRILL...5 S...5 CORE - THIN WALL...7 PILOT DRILL...7 S...7 FAST SPIRAL...9 HAMMER A TAPER...21 B or "K" TAPER mm HEX SLOT mm HEX /8" HEX /4" HEX SLOT /16" HEX /16" HEX...23, 25 SDS - fractional...14 SDS-MAX - (multi-cutter)...18 SDS-MAX - (single cutter)...17 SDS-PLUS...13 SPLINE (multi-cutter)...20 SPLINE (single cutter)...19 TAPCON - TANG STYLE...13 WIDE SPIRAL...10 WIDE SPIRAL - metric...11 YANKEE (PUSH)...11 INTERNET Check us out online at for New Items - Engineering Data - Online Ordering.

3 UNIVERSAL DRILLS ICS WIS HEAVY DUTY MAS-1 PERCUSSION DRILL POINT Carbide Tipped Universal Drills are designed with a diamond ground special drill point for multi-purpose drilling. It is highly effective for drilling hard metals and alloys, reinforced concrete, stone, tile, ceramics, marble, granite, glass, hard and soft woods, plastics and many other difficult materials. Often used to drill out broken taps and hardened bolts. They are also known as Carbide Tipped Multi-Purpose Drills or Carbide Tipped Utility Drills. x 1/8 x 3 1/8 CTUD008 $7.62 1/8 x 12 1/8 CTUD008X /32 x 3-1/8 5/32 CTUD /16 x 3-1/2 3/16 CTUD /16 x 12 3/16 CTUD012X /32 x 3-3/4 7/32 CTUD /4 x 4 1/4 CTUD016X /4 x 6 1/4 CTUD016X /4 x 12 1/4 CTUD016X /32 x 4-1/4 1/4 CTUD /16 x 4-1/2 1/4 CTUD /16 x 6 1/4 CTUD020X /32 x 5 1/4 CTUD /8 x 5 3/8 CTUD /8 x 12 3/8 CTUD024X x ITEM NO. ITEM NO. METRIC S M4.0 x 3 M4.0 CTUDM04.0X03 $ 7.98 M5.0 x 3-3/8 M5.0 CTUDM05.0X M6.0 x 3-13/16 M6.0 CTUDM06.0X M7.0 x 4-3/16 M7.0 CTUDM07.0X x ITEM NO. 13/32 x 6 3/8 CTUD026 $ /32 x 12 3/8 CTUD026X /16 x 6 3/8 CTUD /16 x 12 3/8 CTUD028X /32 x 6 3/8 CTUD /32 x 12 3/8 CTUD030X /2 x 6 3/8 CTUD /2 x 12 3/8 CTUD032X /16 x 6 3/8 CTUD /16 x 16 3/8 CTUD036X /8 x 6 3/8 CTUD /4 x 6 3/8 CTUD /4 x 16 1/2 CTUD048X /8 x 6 1/2 CTUD x 6 1/2 CTUD x ITEM NO. M8.0 x 4-9/16 M8.0 CTUDM08.0X04 $11.04 M10.0 x 5-3/8 M10.0 CTUDM10.0X M12.0 x 6-3/16 M12.0 CTUDM12.0X HARDENED STEEL & CAST IRON CONCRETE & GRANITE UNIVERSAL DRILL APPLICATIONS CERAMIC TILE & MARBLE PORCELAIN & BAKED CERAMIC GLASS, CRYSTAL & MIRROR WOODS & PLASTICS UNIVERSAL DRILL SET ITEM NO. METAL INDEX S 7 PC DRILL SET DS-CTUD-7 7 pc Carbide Tipped Universal Drill Set $ contains 1 each: 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2

4 MAS-2 HARD STEEL DRILLS 130 POINT Carbide Tipped Hard Steel Drills are designed for all hardened steel drilling applications, such as dies, bearing races, and safes. Specially tempered alloy body with long carbide tip to prevent chipping. Ideal for locksmiths, mechanics, etc. Not intended for precision type work. DIA. OVERALL ITEM NO. EACH 1/8 1/8 2-3/4 CTHSD008X02 $ /32 5/32 3 CTHSD010X /64 11/64 3 CTHSD011X /16 3/16 3 CTHSD012X /32 7/32 4 CTHSD014X /4 1/4 4 CTHSD016X /4 1/4 6 CTHSD016X /32 9/32 4 CTHSD018X /16 1/4 4 CTHSD020X Special sizes quoted upon request. DIA. OVERALL ITEM NO. EACH 5/16 5/16 6 CTHSD020X06 $ /8 1/4 4 CTHSD024X /8 3/8 6 CTHSD024X /32 3/8 6 CTHSD026X /16 3/8 6 CTHSD028X /2 1/2 6 CTHSD032X /16 1/2 6 CTHSD036X /8 1/2 6 CTHSD040X LEFT HAND EXTRACTOR DRILLS 130 POINT Carbide Tipped Left Hand Extractor Drills are designed for removing broken bolts, screws and studs. The left handed cutting action assists with backing the threaded fastener out of the hole by its counterclockwise spin. They are often the last resort to removing broken fasteners. DIA. OVERALL EACH ITEM NO. 1/8 1/8 2-3/4 CTHSDL008X02 $ /32 5/32 3 CTHSDL010X /64 11/64 3 CTHSDL011X /16 3/16 3 CTHSDL012X /32 7/32 4 CTHSDL014X /4 1/4 4 CTHSDL016X /4 1/4 6 CTHSDL016X /32 9/32 4 CTHSDL018X Special sizes quoted upon request. DIA. OVERALL ITEM NO. EACH 5/16 1/4 4 CTHSDL020X04 $ /16 5/16 6 CTHSDL020X /8 1/4 4 CTHSDL024X /8 3/8 6 CTHSDL024X /16 3/8 6 CTHSDL028X /2 1/2 6 CTHSDL032X /16 1/2 6 CTHSDL036X /8 1/2 6 CTHSDL040X

5 MAS-3 PLATE CUTTERS MULTI-TOOTH WET OR DRY USE Carbide Tipped Plate Cutters are designed with a multi-tooth center head for drilling through a combination of concrete and steel plates well as embedded rebar and wire mesh. They can be run wet using a small amount of water or run dry. Carbide tipped plate cutters are a viable alternative to fragile diamond core drills as they will withstand rough usage. They can be used with either vacuum or magnetic based diamond drilling machines. HUB THREAD x ITEM NO. 1/2 x 12 5/8-11 CTPC032X12 $ /8 x 12 5/8-11 CTPC040X /4 x 12 5/8-11 CTPC048X /8 x 12 5/8-11 CTPC056X HUB THREAD x ITEM NO. 1 x 12 5/8-11 CTPC100X12 $ /8 x 12 5/8-11 CTPC108X /4 x 12 5/8-11 CTPC116X /2 x 12 5/8-11 CTPC132X Sizes up to 12" diameter available upon request. PLATE CUTTER ADAPTER Adapts plate cutters for use in any 1/2" rotary style drill with a Jacobs (three-jaw) style chuck. DESCRIPTION ITEM NO. 1/2 Round Shank to 5/8-11 CTPCA $ /2 Round Shank to 1-1/4-7 CTPCA SUGGESTED DRILL SPEEDS FOR PLATE CUTTERS S HUB THREAD RPM 1/2-1-3/8 5/ RPM 1-1/2 5/ RPM 1-3/ / RPM

6 MAS-4 ICS USA REBAR CUTTERS HEAVY DUTY MULTI-TOOTH Carbide Tipped Rebar Cutters are designed with a multi-tooth cutter head for drilling through concrete and embedded rebar or wire mesh. Use either water or cutting oil for lubrication and cooling. They can be used in any 1/2 rotary drill with a 3-jawed chuck or directly into SDS, Spline Drive, or SDS-Max Hammer Drills using an ICS rebar cutter adapter. HUB THREAD x ITEM NO. 1/2 x 12 5/8-11 CTRC032X12 $ /8 x 12 5/8-11 CTRC040X /4 x 12 5/8-11 CTRC048X /8 x 12 5/8-11 CTRC056X Sizes up to 3" diameter available upon request. REBAR CUTTER ADAPTERS Adapts rebar and plate cutters for use in various style masonry drills. RCA-RS HUB THREAD x ITEM NO. 1 x 12 5/8-11 CTRC100X12 $ /8 x 12 5/8-11 CTRC108X /4 x 12 5/8-11 CTRC116X /2 x 12 5/8-11 CTRC132X ITEM NO. FITS 1/2" Rotary Style Drills $30.00 RCA-SDS SDS Hammer Drills RCA-S Spline Drive Hammer Drills RCA-MAX SDS-Max Hammer Drills Stop drilling as soon as carbide tip comes in contact with rebar. (If you do not - drill will be damaged.) HOW TO DRILL REBAR 2. Replace carbide tipped drill with rebar cutter. Insert into hole and drill through embedded rebar. (Maintain even and constant pressure.) 3. Replace rebar cutter with carbide tipped drill and finish drilling the hole. NOTICE Rebar cutters can also be used in most hammer drills equipped with a three-jaw style chuck, provided the selector is kept in the rotary-only position. Percussion (hammering action) will damage the tool. The ICS Rebar Cutter is designed for rotary drilling only.

7 MASONRY (ROTARY) CORE DRILL BITS ICS USA GENERAL PURPOSE MULTI-TOOTH MAS-5 Carbide Tipped Rotary Core Drill Bits are designed for drilling large diameter holes in thin or brittle material that would be damaged if done with a hammer core drill. Carbide tipped teeth cut only the rim of the hole leaving the core intact which should be broken up and removed every 4 for maximum drilling depth. x ITEM NO. 1/2 x 6 3/8 MD-RC032X06 $ /8 x 8 3/8 MD-RC040X /4 x 10 1/2 MD-RC048X /8 x 10 1/2 MD-RC056X x 10 1/2 MD-RC100X /8 x 12 1/2 MD-RC108X x ITEM NO. 1-1/4 x 12 1/2 MD-RC116X12 $ /8 x 12 1/2 MD-RC124X /2 x 12 1/2 MD-RC132X /8 x 12 1/2 MD-RC156X x 12 3/4 MD-RC200X ROTARY CORE PILOT DRILL ROTARY CORE S EXTRA LONG Use a pilot drill for a more accurate starting position and to keep the drill from walking. The pilot drill is used only to start the initial starting groove and is then removed before drilling is continued. FITS DRILL ITEM NO. 5/8 to 1 MD-RCPD #1 $ /8 to 2-1/4 MD-RCPD # x ITEM NO. 3/8 x 12 3/8-16 MD-RCS024X12 $ /8 x 18 3/8-16 MD-RCS024X /2 x 12 1/2-13 MD-RCS032X /2 x 18 1/2-13 MD-RCS032X /4 x 12 3/4-10 MD-RCS048X /4 x 18 3/4-10 MD-RCS048X

8 MAS-6 MASONRY (WET DRILLING) DIAMOND CORE DRILLS ICS KOR SPECIAL PURPOSE DIAMOND SEGMENTS PREMIUM GRADE 13" DRILLING DEPTH Wet Drilling Diamond Core Drills are used for cutting miscellaneous types of concrete, masonry, and stone. They are made to cool from the center and should be used in either vacuum or magnetic based diamond drilling machines. Use either water or cutting oil for lubrication and cooling. Do not use dry or use in a hammer drill. SEGMENT S x.275 MD-DCWP0100 $ /8.118 x.275 MD-DCWP /4.118 x.275 MD-DCWP /8.118 x.275 MD-DCWP /2.157 x.275 MD-DCWP /8.157 x.275 MD-DCWP /4.157 x.275 MD-DCWP /8.157 x.275 MD-DCWP x.275 MD-DCWP /4.157 x.275 MD-DCWP /2.177 x.275 MD-DCWP /4.177 x.275 MD-DCWP x.275 MD-DCWP /4.177 x.275 MD-DCWP /2.177 x.275 MD-DCWP x.275 MD-DCWP /4.197 x.275 MD-DCWP ITEM NO. SEGMENT S ITEM NO. 4-1/2.197 x.275 MD-DCWP0432 $ x.275 MD-DCWP /4.217 x.275 MD-DCWP /2.217 x.275 MD-DCWP /4.217 x.275 MD-DCWP x.275 MD-DCWP /4.217 x.275 MD-DCWP /2.217 x.275 MD-DCWP x.275 MD-DCWP x.275 MD-DCWP x.275 MD-DCWP x.275 MD-DCWP x.275 MD-DCWP x.275 MD-DCWP x.275 MD-DCWP x.275 MD-DCWP x.275 MD-DCWP1600 CALL 1" to 1-3/4" Diamond Core Drills have a 5/8-11 thread. 2" to 18" Diamond Core Drills have a 1-1/4-7 thread. Dry Drilling Diamond Core Drills and Diamond Core Drill Machines are available upon request.

9 ICS MASONRY (THIN WALL) CORE DRILLS USA HEAVY DUTY MULTI-TOOTH MAS-7 SCREW TOGETHER STYLE 3 PC ASSEMBLY Special Carbide Tipped Thin Wall Percussion Core Bits are designed to drill large diameter holes with most rotary hammer drills. Carbide Tips can withstand continuous hammering action and give maximum drilling life. CORE BITS FOR THIN WALL CORE DRILLS THIN WALL CORE BODY BODY NO. OF TEETH ITEM NO. 1-1/2 4 6 MD-TWC132 $ /4 4 6 MD-TWC MD-TWC /2 4 9 MD-TWC MD-TWC /2 4 9 MD-TWC MD-TWC S FOR THIN WALL CORE DRILLS FITS HAMMER MODEL ITEM NO. 12" 18" Fits all Popular Spline Drive Power Tools. See pages for complete listing. MD-TWCS 12SP $71.12 MD-TWCS 18SP Only fits 1-1/2" dia. core drills Fits 1-3/4" to 4" dia. core drills 12" 18" 8" 16" 8" 12" Bosch 11216, SDS-MAX Hilti TE 64, TE-Y Hilti TE 72, 90 Fits all popular 4 slot power tools. See pages for complete listing. Fits all popular 4 slot power tools. See pages for complete listing. MD-TWCS 12MAX MD-TWCS 18MAX MD-TWCS 08SDS MD-TWCS 16SDS MD-TWCS 08SDSL MD-TWCS 12SDSL PILOT DRILL FOR THIN WALL CORE DRILLS CUTTING APPLICATION ITEM NO. Use a pilot drill for a more accurate MD-TWCS PD $19.60 starting position and to keep the hammer core drill from walking. The pilot drill is used only to start the initial starting groove and is then removed before drilling is continued.

10 MAS-8 MASONRY (PERCUSSION HAMMER) CORE DRILLS ICS WIS HEAVY DUTY MULTI-TOOTH TAPER FIT STYLE 3 PC ASSEMBLY Special Carbide Tipped Percussion Core Bits are designed to drill large diameter holes with most rotary hammer drills. Carbide Tips can withstand continuous hammering action and give maximum drilling life. CORE BITS FOR PERCUSSION HAMMER CORE DRILLS TAPERED CORE BODY BODY NO. OF TEETH ITEM NO. 1-1/2 4 6 MD-PC132 $ MD-PC /2 4 9 MD-PC MD-PC /2 4 9 MD-PC MD-PC MD-PC S FOR PERCUSSION HAMMER CORE DRILLS FITS HAMMER MODEL ITEM NO. 9" Fits all Popular Spline Drive MD-PCS 09SP $ " Power Tools. See pages 27- MD-PCS 14SP " 28 for complete listing. MD-PCS 22SP Bosch 11216, SDS-MAX 8" Hilti TE 64, TE-Y MD-PCS 08MAX " Hilti TE 72, 90 MD-PCS 18MAX PERCUSSION CORE PILOT DRILL MASONRY DRILL EJECTOR KEY Use a pilot drill for a more accurate starting position and to keep the hammer core drill from walking. The pilot drill is used only to start the initial starting groove and is then removed before drilling is continued. AND DESCRIPTION 3/8 x 5 A-Taper Shank ITEM NO. MD-PCPD $13.14 Use Ejector Key to push Pilot Drill out of Tapered Core Body. ITEM NO. MD-EK $6.62

11 MASONRY DRILLS ICS USA GENERAL PURPOSE MAS-9 ROTARY DRILL POINT BLACK FINISH FAST SPIRAL Carbide Tipped Fast Spiral Masonry Drill Bits are designed for rotary drilling into brick, cinder block, tile, plaster, and other brittle materials. Brittle materials will require slower speeds and light to moderate pressure as material is being ground, not broken. The fast spiral flute design creates less heat buildup when drilling. Has a special carbide tip with 130 point and positive angles for fast penetration. They can be used in any 3-jaw chuck rotary style drill. PACKAGING: 1 drill/vinyl pouch or plastic tube MASONRY DRILL DISPLAYS * 1/8 Masonry Drill in MDD-306 Display is 3" long, not 6". ZINC PLATED NOMINAL BLACK FINISH ZINC PLATED NOMINAL BLACK FINISH ZINC PLATED x ITEM NO. ITEM NO. x ITEM NO. ITEM NO. 1/8 x 3 1/8 MDF008X03 $1.80 MDFZ008X03 $1.80 7/16 x 6 1/4 MDF028X06 $4.16 MDFZ028X06 $4.16 3/16 x 4 3/16 MDF012X MDFZ012X /2 x 4 1/4 MDF032X MDFZ032X /16 x 6 3/16 MDF012X MDFZ012X /2 x 6 1/4 MDF032X MDFZ032X /4 x 4 1/4 MDF016X MDFZ016X /2 x 13 3/8 MDF032X MDFZ032X /4 x 6 1/4 MDF016X MDFZ016X /16 x 6 3/8 MDF036X MDFZ036X /4 x 13 1/4 MDF016X MDFZ016X /16 x 13 3/8 MDF036X MDFZ036X /16 x 4 1/4 MDF020X MDFZ020X /8 x 6 3/8 MDF040X MDFZ040X /16 x 6 1/4 MDF020X MDFZ020X /8 x 13 3/8 MDF040X MDFZ040X /16 x 13 1/4 MDF020X MDFZ020X /4 x 6 1/2 MDF048X MDFZ048X /8 x 4 1/4 MDF024X MDFZ024X /4 x 13 1/2 MDF048X MDFZ048X /8 x 6 1/4 MDF024X MDFZ024X /8 x 6 1/2 MDF056X MDFZ056X /8 x 13 1/4 MDF024X MDFZ024X x 6 1/2 MDF100X MDFZ100X MASONRY DRILL SETS VINYL POUCHES DESCRIPTION ITEM NO. TYPE OF DRILL 4 PC DRILL SET MDS-MDF-04 Fast Spiral Masonry Drills CALL 1/4, 5/16, 3/8, 1/2 MDS-MDW-04 Wide Spiral Masonry Drills CALL 4" Long Masonry Drills DESCRIPTION ITEM NO. TYPE OF DRILL 30 PC DRILL DISPLAY MDD-MDF-304 Fast Spiral Masonry Drills $ ea. 1/8, 3/16, 1/4, 5/16, 3/8, 1/2 MDD-MDW-304 Wide Spiral Masonry Drills " Length Masonry Drills Display Size: 12" x 10-1/2" 18 PC DRILL DISPLAY MDD-MDF-186 Fast Spiral Masonry Drills ea. 1/4, 5/16, 3/8, 1/2, 5/8, 3/4 MDD-MDW-186 Wide Spiral Masonry Drills " Length Masonry Drills Display Size: 12" x 12" 30 PC DRILL DISPLAY MDD-MDF-306 *Fast Spiral Masonry Drills ea. 1/8, 3/16, 1/4, 5/16, 3/8 MDD-MDW-306 *Wide Spiral Masonry Drills ea. 7/16, 1/2, 9/16, 5/8, 3/4 6" Length Masonry Drills Display Size: 18" x 12" 6 PC DRILL DISPLAY MDD-MDF-613 Fast Spiral Masonry Drills ea. 1/4, 5/16, 3/8, 1/2, 5/8, 3/4 MDD-MDW-613 Wide Spiral Masonry Drills " Length Masonry Drills Display Size: 12" x 18" 6 PC DRILL DISPLAY MDD-MDW-618 Wide Spiral Masonry Drills ea. 1/4, 5/16, 3/8, 1/2, 5/8, 3/4 18" Length Masonry Drills Display Size: 12" x 23"

12 MAS-10 MASONRY DRILLS ICS USA GENERAL PURPOSE ROTARY DRILL POINT BLACK FINISH WIDE SPIRAL ZINC PLATED Carbide Tipped Wide Spiral Masonry Drill Bits are designed for rotary drilling into concrete, masonry, marble, stone and rock. The harder the material, the more pressure applied and the slower the speed as material is being ground up, not broken as a hammer drill would do. The wide spiral flute design is very strong and removes debris rapidly. Drills have a special carbide tip with a 130 point and positive angle for fast penetration. They can be used in any 3-Jaw chuck rotary style drill. They are also known as Carbide Tipped Slow Spiral Masonry Drill Bits. NOMINAL BLACK FINISH ZINC PLATED NOMINAL BLACK FINISH ZINC PLATED x ITEM NO. ITEM NO. x ITEM NO. ITEM NO. 1/8 x 3 1/8 MDW008X03 $ 1.80 MDWZ008X03 $ /2 x 4 1/4 MDW032X04 $ 3.92 MDWZ032X04 $ /32 x 3 9/64 MDW010X MDWZ010X /2 x 6 1/4 MDW032X MDWZ032X /64 x 3 9/64 MDW011X MDWZ011X /2 x 6A 3/8 MDW032X06A 4.72 MDWZ032X06A /16 x 4 3/16 MDW012X MDWZ012X /2 x 13 3/8 MDW032X MDWZ032X /16 x 6 3/16 MDW012X MDWZ012X /2 x 18 3/8 MDW032X MDWZ032X /32 x 4 3/16 MDW014X MDWZ014X /2 x 24 3/8 MDW032X MDWZ032X /64 x 4 3/16 MDW015X MDWZ015X /2 x 30 3/8 MDW032X MDWZ032X /4 x 4 1/4 MDW016X MDWZ016X /16 x 6 3/8 MDW036X MDWZ036X /4 x 6 1/4 MDW016X MDWZ016X /16 x 13 1/2 MDW036X MDWZ036X /4 x 13 1/4 MDW016X MDWZ016X /16 x 18 1/2 MDW036X MDWZ036X /4 x 18 1/4 MDW016X MDWZ016X /8 x 6 3/8 MDW040X MDWZ040X /4 x 24 1/4 MDW016X MDWZ016X /8 x 6A 1/2 MDW040X06A 6.96 MDWZ040X06A /4 x 30 1/4 MDW016X MDWZ016X /8 x 13 1/2 MDW040X MDWZ040X /32 x 4 1/4 MDW018X MDWZ018X /8 x 18 1/2 MDW040X MDWZ040X /16 x 4 1/4 MDW020X MDWZ020X /16 x 6 1/2 MDW044X MDWZ044X /16 x 6 1/4 MDW020X MDWZ020X /4 x 6 3/8 MDW048X MDWZ048X /16 x 13 1/4 MDW020X MDWZ020X /4 x 6A 1/2 MDW048X06A MDWZ048X06A /16 x 18 1/4 MDW020X MDWZ020X /4 x 13 1/2 MDW048X MDWZ048X /16 x 24 1/4 MDW020X MDWZ020X /4 x 18 1/2 MDW048X MDWZ048X /16 x 30 1/4 MDW020X MDWZ020X /8 x 6 1/2 MDW056X MDWZ056X /8 x 4 1/4 MDW024X MDWZ024X /8 x 13 1/2 MDW056X MDWZ056X /8 x 6 1/4 MDW024X MDWZ024X /8 x 18 1/2 MDW056X MDWZ056X /8 x 6A 3/8 MDW024X06A 3.60 MDWZ024X06A x 6 1/2 MDW100X MDWZ100X /8 x 13 1/4 MDW024X MDWZ024X x 13 1/2 MDW100X MDWZ100X /8 x 18 3/8 MDW024X MDWZ024X x 18 1/2 MDW100X MDWZ100X /8 x 24 3/8 MDW024X MDWZ024X /8 x 6 1/2 MDW108X MDWZ108X /8 x 30 3/8 MDW024X MDWZ024X /8 x 10 1/2 MDW108X MDWZ108X /16 x 4 1/4 MDW028X MDWZ028X /4 x 10 1/2 MDW116X MDWZ116X /16 x 6 1/4 MDW028X MDWZ028X /4 x 18 1/2 MDW116X MDWZ116X /16 x 6A 3/8 MDW028X06A 4.16 MDWZ028X06A /8 x 10 1/2 MDW124X MDWZ124X /16 x 13 3/8 MDW028X MDWZ028X /8 x 18 1/2 MDW124X MDWZ124X /16 x 18 3/8 MDW028X MDWZ028X /2 x 10 1/2 MDW132X MDWZ132X /2 x 18 1/2 MDW132X MDWZ132X PACKAGING 1/8 x 3" to 3/4 x 18" Length - 1 Drill/Vinyl Pouch 7/8 x 6" up to 1-1/2 x 18" Length - 1 Drill/Tube 1/4 x 24" up to 1/2 x 30" Length - 1 Drill/Tube

13 METRIC MASONRY DRILLS ICS USA GENERAL PURPOSE ROTARY STYLE PERCUSSION DRILL POINT WIDE SPIRAL MAS-11 Carbide Tipped Wide Spiral Metric Masonry Drill Bits are designed for rotary drilling into concrete, masonry, marble, stone and rock. The harder the material, the more pressure applied and the slower the speed as material is being ground up, not broken as a hammer drill would do. The wide spiral flute design is very strong and removes debris rapidly. Drills have a special carbide tip with a 130 point and positive angle for fast penetration. They can be used in any 3-Jaw chuck rotary style drill. ICS Carbide Tipped Metric Drills are true metric sizes (not fractional equivalents) for drilling pilot holes for European Anchors. They are also known as Carbide Tipped Slow Spiral Metric Masonry Drill Bits. Note: Metric Diameter Drills must be used for drilling metric size anchor holes to ensure proper fit for metric size anchors. x (MM) ITEM NO. 3.0 x MD-M03.0X075 $ x MD-M03.5X x MD-M04.0X x MD-M04.5X x MD-M05.0X x MD-M05.5X x MD-M06.0X x MD-M06.5X x MD-M07.0X x MD-M08.0X x MD-M09.0X CARPET STUBBY DRILLS SPECIAL PURPOSE x (MM) ITEM NO x MD-M10.0X120 $ x MD-M11.0X x MD-M12.0X x MD-M13.0X x MD-M14.0X x MD-M16.0X x MD-M18.0X x MD-M19.0X x MD-M20.0X x MD-M22.0X x MD-M25.0X YANKEE (PUSH) DRILLS SPECIAL PURPOSE Carbide Tipped Carpet Stubby Drills are designed specially for easy installation of carpets. They are used to drill holes in concrete or terrazzo flooring for tack stripping. OVERALL 1/8 1-7/8 CTCSD008 $2.24 ITEM NO. Carbide Tipped Yankee Push Drills are designed to fit Yankee Push Drill systems where 3/16" and 1/4" anchor holes are required. They are ideal for drywall and concrete block. GLASS DRILLS ICS USA SPECIAL PURPOSE OVERALL ITEM NO. SPEAR POINT 3/16 2-1/8 CTYPD012 $4.08 1/4 2-1/8 CTYPD Carbide Tipped Glass Drills are designed for drilling glass, mirror glass, tile, ceramics, and porcelain. Special spear point allows a precise hole to start without walking and can also be used to drill a hole smaller than drill diameter. For best results, apply firm pressure at low speed, using water or turpentine as a lubricant. OVERALL ITEM NO. EACH 1/8 2-1/2 CTGD008 $6.50 5/32 2-1/2 CTGD /16 2-1/2 CTGD /4 2-1/2 CTGD /16 2-1/2 CTGD /8 3 CTGD OVERALL ITEM NO. EACH 1/2 3 CTGD032 $ /16 4 CTGD /8 4 CTGD /4 4 CTGD /8 4 CTGD CTGD

14 MAS-12 MASONRY HAMMER DRILLS PERCUSSION DRILL POINT DUAL PURPOSE WIDE SPIRAL Carbide Tipped Wide Spiral Flute Masonry Hammer Drill Bits are designed for rotary or percussion drilling into concrete, masonry, marble, stone and rock. The impact action and rotation created by the percussion drill breaks up the concrete for faster use and harder materials. Has a special carbide tip with a 130 point and negative angle for fast penetration in percussion mode, but drill 10% slower when in rotary mode. NOMINAL x ITEM NO. 1/8 x 3 1/8 MDH008X03 $ /32 x 3 9/64 MDH010X /64 x 3 9/64 MDH011X /16 x 4 3/16 MDH012X /16 x 6 3/16 MDH012X /32 x 4 3/16 MDH014X /4 x 4 1/4 MDH016X /4 x 6 1/4 MDH016X /4 x 13 1/4 MDH016X /4 x 18 1/4 MDH016X /4 x 24 1/4 MDH016X /4 x 30 1/4 MDH016X /32 x 4 1/4 MDH018X /16 x 4 1/4 MDH020X /16 x 6 1/4 MDH020X /16 x 13 1/4 MDH020X /16 x 18 1/4 MDH020X /16 x 24 1/4 MDH020X /16 x 30 1/4 MDH020X /8 x 4 1/4 MDH024X /8 x 6 1/4 MDH024X /8 x 6 3/8 MDH024X06A /8 x 13 1/4 MDH024X /8 x 18 3/8 MDH024X /8 x 24 3/8 MDH024X /8 x 30 3/8 MDH024X /16 x 4 1/4 MDH028X /16 x 6 1/4 MDH028X /16 x 6 3/8 MDH028X06A /16 x 13 3/8 MDH028X13 CALL NOMINAL x ITEM NO. 7/16 x 18 3/8 MDH028X18 $ /2 x 4 1/4 MDH032X /2 x 6 1/4 MDH032X /2 x 6 3/8 MDH032X06A /2 x 13 3/8 MDH032X /2 x 18 3/8 MDH032X /2 x 24 3/8 MDH032X /2 x 30 3/8 MDH032X /16 x 6 3/8 MDH036X /16 x 13 1/2 MDH036X /16 x 18 1/2 MDH036X /8 x 6 3/8 MDH040X /8 x 6 1/2 MDH040X06A /8 x 13 1/2 MDH040X /8 x 18 1/2 MDH040X /16 x 6 1/2 MDH044X /4 x 6 3/8 MDH048X /4 x 6 1/2 MDH048X06A /4 x 13 1/2 MDH048X /4 x 18 1/2 MDH048X /8 x 6 1/2 MDH056X /8 x 13 1/2 MDH056X /8 x 18 1/2 MDH056X x 6 1/2 MDH100X x 13 1/2 MDH100X x 18 1/2 MDH100X /8 x 6 1/2 MDH108X /4 x 18 1/2 MDH116X /8 x 18 1/2 MDH124X /2 x 18 1/2 MDH132X PACKAGING 1/8 x 3" to 3/4 x 18" Length - 1 Drill/Vinyl Pouch 7/8 x 6" to 1-1/2 x 18" Length - 1 Drill/Tube 1/4 x 24" to 1/2 x 30" Length - 1 Drill/Tube NOTE Extra Long Carbide Tipped Bellhanger Masonry Drills on page 108 are designed to do very deep hole drilling. Lengths up to 72" are available.

15 STRAIGHT TAPCON BITS - TANG STYLE ICS USA SPECIAL PURPOSE MAS-13 ROTARY DRILL POINT STRAIGHT TANG WIDE SPIRAL Carbide Tipped Straight Shank Tapcon Bits are designed for use in Tapcon, Condrive, and Black and Decker drilling systems for setting masonry anchor screws with self-cutting threads. Straight shank Tapcon bits can be used in any drill with 3-jawed drill chuck. All ICS straight shank Tapcon bits meet or exceed all tolerances recommended by manufacturers of screw-type masonry anchors. They are also known as Screw-Type Anchor Bits or Concrete Screw Drill Bits. FOR THESE x ANCHORS ITEM NO. FOR THESE x ANCHORS ITEM NO. 3/16 x 1-1/4 3/16 x 1-3/4 5/32 x 3-1/2 MD-TC 010 x 03 $2.48 3/16 x 3-1/2 1/4 x 1-1/4 1/4 x 1-3/4 MD-TC 012 x 03 $2.58 3/16 x 1-3/4 3/16 x 2-1/4 3/16 x 2-3/4 3/16 x 3-1/4 3/16 x 3-3/4 3/16 x 4 5/32 x 4-1/2 5/32 x 5-1/2 MD-TC 010 x 04 MD-TC 010 x /16 x 4-1/2 3/16 x 5-1/2 3/16 x 6-3/4 1/4 x 2-1/4 1/4 x 2-3/4 1/4 x 3-1/4 1/4 x 3-3/4 1/4 x 4 1/4 x 5 MD-TC 012 x 04 MD-TC 012 x 05 MD-TC 012 x /16 x 7-5/8 1/4 x 6 MD-TC 012 x SDS-PLUS TAPCON HEX ROTARY HAMMER BITS ICS WIS HEAVY DUTY 4 SLOT (SDS) HEX DRIVE WIDE SPIRAL Carbide Tipped SDS-Plus Tapcon Hex Drive Rotary Hammer Bits are designed for use in Tapcon, Condrive, and Black and Decker drilling systems for setting masonry anchor screws with self-cutting threads. SDS-Plus Tapcon hex drive bits have a 5/16" hex directly below the shank which fits into driver sleeve for installation. All ICS SDS-Plus Tapcon hex drive rotary hammer bits meet or exceed all tolerances recommended by manufacturers of screw-type masonry anchors. They are also known as Carbide Tipped Screw-Type Anchor Bits or Carbide Tipped Concrete Screw Drill Bits. NOMINAL x 5/32 x 5 5/32 x 7 FOR THESE NOMINAL FOR THESE ANCHORS ITEM NO. x ANCHORS ITEM NO. 3/16 x 3-1/4 3/16 x 3-3/4 3/16 x 4 MD-SDSH 010 x 05 MD-SDSH 010 x 07 $ /16 x 5 1/4 x 3-1/4 1/4 x 3-3/4 MD-SDSH 012 x 05 $ /4 x /16 x 7 1/4 x 5 1/4 x 6 MD-SDSH 012 x

16 MAS-14 MASONRY (SDS ) HAMMER DRILLS 4 SLOT SDS PARABOLIC FLUTE Carbide Tipped Slot Drive System SDS Masonry Hammer Drills are designed for use with all rotary hammer that specify SDS-Plus shank hammer drills. SDS plus shank hammer bits have 4 U-shaped slots cut into the.393 diameter shank, 2 positive rotary drive slots and 2 ball retainer slots to ensure a positive fit between the bit and the bit holder on a SDS-Plus rotary hammer drill which makes possible the most power transmission to the cutting edge for high speed drilling of holes up to 1" in diameter in concrete, masonry and stone. They are also known as SDS- Plus Drill Bits. NOMINAL DRILLING 5/32 x 4-1/2 2 MD-SDS010X04 $8.76 3/16 x 4-1/2 2 MD-SDS012X /16 x 6-1/2 4 MD-SDS012X /16 x 8 6 MD-SDS012X /16 x 10 8 MD-SDS012X /16 x MD-SDS012X /32 x 6 4 MD-SDS014X /32 x 8 6 MD-SDS014X /32 x MD-SDS014X /4 x 4 2 MD-SDS016X /4 x 6 4 MD-SDS016X /4 x 9 6 MD-SDS016X /4 x 12 9 MD-SDS016X /4 x MD-SDS016X /4 x MD-SDS016X /16 x 4-1/2 2 MD-SDS020X /16 x 6 4 MD-SDS020X /16 x MD-SDS020X /8 x 6 4 MD-SDS024X /8 x 9 6 MD-SDS024X /8 x MD-SDS024X /8 x MD-SDS024X /8 x MD-SDS024X /8 x MD-SDS024X /8 x MD-SDS024X /16 x 6 4 MD-SDS028X /16 x MD-SDS028X /16 x MD-SDS028X /2 x 6 4 MD-SDS032X NOMINAL x DRILLING DEPTH ITEM NO. 1/2 x 9 6 MD-SDS032X09 $ /2 x MD-SDS032X /2 x MD-SDS032X /2 x MD-SDS032X /2 x MD-SDS032X /16 x 6 4 MD-SDS036X /16 x MD-SDS036X /16 x MD-SDS036X /8 x 6 4 MD-SDS040X /8 x 9 6 MD-SDS040X /8 x MD-SDS040X /8 x MD-SDS040X /8 x MD-SDS040X /8 x MD-SDS040X /16 x 9 6 MD-SDS044X /4 x 6 4 MD-SDS048X /4 x 9 6 MD-SDS048X /4 x MD-SDS048X /4 x MD-SDS048X /4 x MD-SDS048X /32 x 9 6 MD-SDS054X /8 x 6 4 MD-SDS056X /8 x 9 6 MD-SDS056X /8 x MD-SDS056X /8 x MD-SDS056X x 9 6 MD-SDS100X x MD-SDS100X x MD-SDS100X x MD-SDS100X MASONRY (SDS ) DRILL SETS METAL CASE ITEM NO. TYPE OF DRILL 7 PC DRILL SETS MDS-SDS-7 Masonry (SDS Shank) Hammer Drills $93.08 MDS-RAM-7 Masonry (Ramset Shank) Hammer Drills each: 3/16 x 4, 1/4 x 4 2 each: 1/4 x 6 1 each: 5/16 x 6, 3/8 x 6, 1/2 x 6 S OF MASONRY DRILLS IN SETS Sizes 3/16 to 1/2 (Wt lbs.)

17 ICS WIS SDS QUICK RELEASE ADAPTERS ADAPTERS FOR HILTI TE-12, 17, 22, SDS, AND RAMSET SDS Shank adapters allow you to use 2 slot and 4 slot shank masonry drills with different models of electric hammer drills. Each shank configuration will fit the hammer drill model No. s listed. MAS-15 FITS HAMMER MODEL ITEM NO. Fits all popular spline drive power tools. See pages for complete listing. SDS-Spline Hilti TE 52, 60 Hilti TE 70, 92 SDS-TE Bosch 11216, SDS-MAX Hilti TE 64, TE-Y Hilti TE 52, 60 Hilti TE 72, 92 SDS-MAX Important: Adapters are designed for intermittent use. A power loss of 10-15% and increased bit wear of 15-20% will result when using adapters. HOW TO USE SDS QUICK RELEASE ADAPTERS STEP 1. STEP 2. Pull back locking sleeve. Use this position to insert or remove drill bit.

18 MAS-16 MASONRY (2 SLOT ) HAMMER DRILLS 2 SLOT 3/4" DIA. FOR USE WITH HILTI TE 52, 60, 72, 92 HAMMER DRILL PARABOLIC FLUTE Special impact carbide tip with negative tip angle and 130 point. Made to withstand the shock and impact of the hardest hitting rotary hammer drills. Will quickly penetrate the toughest aggregate. 3/8 x 12 6 MD-TE60-024X12 $ /2 x 12 6 MD-TE60-032X /2 x MD-TE60-032X /2 x MD-TE60-032X /8 x 12 6 MD-TE60-040X /8 x MD-TE60-040X /8 x MD-TE60-040X /4 x 12 6 MD-TE60-048X /4 x MD-TE60-048X /4 x MD-TE60-048X /8 x 12 6 MD-TE60-056X /8 x MD-TE60-056X /8 x MD-TE60-056X x 12 6 MD-TE60-100X12 $ x MD-TE60-100X x MD-TE60-100X /8 x MD-TE60-108X /8 x MD-TE60-108X /4 x MD-TE60-116X /4 x MD-TE60-116X /4 x MD-TE60-116X /8 x MD-TE60-124X /8 x MD-TE60-124X /2 x MD-TE60-132X /2 x MD-TE60-132X /2 x MD-TE60-132X MASONRY (4 SLOT ) HAMMER DRILLS 4 SLOT MAGIC PARABOLIC FLUTE Use in Ramset Dinadrill #330 or any SDS style power drill. They fit all two and four slot drive systems. Special impact carbide tip with negative angle and 130 point. 3/16 x 4-1/2 2 MD-RAM012X04 $ /16 x 6 4 MD-RAM012X /4 x 4-1/2 2 MD-RAM016X /4 x 6-1/2 4 MD-RAM016X /4 x 8 6 MD-RAM016X /16 x 6 4 MD-RAM020X /16 x 9 6 MD-RAM020X /16 x MD-RAM020X /8 x 6-1/2 4 MD-RAM024X /8 x 9 6 MD-RAM024X /8 x MD-RAM024X /16 x 6 4 MD-RAM028X /16 x MD-RAM028X /16 x MD-RAM028X /2 x 6-1/2 4 MD-RAM032X /2 x 9 6 MD-RAM032X /2 x MD-RAM032X /2 x MD-RAM032X /16 x 6 4 MD-RAM036X06 $ /16 x MD-RAM036X /16 x MD-RAM036X /8 x 6 4 MD-RAM040X /8 x 9 6 MD-RAM040X /8 x 12 8 MD-RAM040X /8 x MD-RAM040X /16 x 6 4 MD-RAM044X /4 x 6 4 MD-RAM048X /4 x 9 6 MD-RAM048X /4 x MD-RAM048X /4 x MD-RAM048X /32 x 6 4 MD-RAM054X /8 x 6 4 MD-RAM056X /8 x 9 6 MD-RAM056X /8 x MD-RAM056X x 10 6 MD-RAM100X x MD-RAM100X

19 ICS MASONRY (SDS-MAX) HAMMER DRILLS USA HEAVY DUTY MAS-17 5 SLOT SDS-MAX SINGLE CUTTER DESIGN PARABOLIC FLUTE Carbide Tipped SDS-MAX Heavy Duty Slot Drive Masonry Hammer Drills with single cutting edge are designed for use with large SDS-MAX drive rotary hammers. SDS-MAX drive hammer bits have 5 U-shaped slots cut into the.708 diameter shank, 3 positive rotary drive slots, and 2 ball retainer slots to hold bit in rotary hammer. They are used for drilling large diameter holes in concrete, masonry and stone. 3/8 x 13-1/2 7 MD-MAX024X13 $ /2 x 13-1/2 7 MD-MAX032X /2 x MD-MAX032X /2 x MD-MAX032X /2 x MD-MAX032X /16 x 13 7 MD-MAX036X /16 x MD-MAX036X /8 x 13 7 MD-MAX040X /8 x MD-MAX040X /8 x MD-MAX040X /8 x MD-MAX040X /4 x 13 7 MD-MAX048X /4 x MD-MAX048X /4 x MD-MAX048X30 $ /4 x MD-MAX048X /8 x 13 8 MD-MAX056X /8 x MD-MAX056X x 13 8 MD-MAX100X x MD-MAX100X x MD-MAX100X /8 x 13 8 MD-MAX108X /8 x MD-MAX108X /4 x MD-MAX116X /4 x MD-MAX116X /8 x MD-MAX124X /2 x MD-MAX132X SLOT (SDS-MAX ) BITS FIT THE FOLLOWING HAMMERS BOSCH HILTI HILTI TE-54 TE 52, 60 SDS-MAX TE-Y (New) TE 72, 92

20 MAS-18 MASONRY (SDS-MAX) HAMMER DRILLS 5 SLOT SDS-MAX MULTI CUTTER DESIGN PARABOLIC FLUTE Carbide Tipped SDS-MAX Heavy Duty Slot Drive Masonry Hammer Drills with 4 cross cutting edges are designed for use with large SDS-MAX drive rotary hammers. The 4 cross cutting edges pulverize the material to be drilled better and quicker than single edge hammer bits. SDS-MAX drive hammer bits have 5 U-shaped slots cut into the.708" diameter shank, 3 positive rotary drive slots, and 2 ball retainer slots to hold bit in rotary hammer. It is the toughest drill of its kind and is often used instead of a carbide tipped core drill for drilling large diameter holes in concrete, masonry and stone. 3/8 x 13 7 MD-MAXX024X13 $ /2 x 13 7 MD-MAXX032X /2 x MD-MAXX032X /2 x MD-MAXX032X /2 x MD-MAXX032X /16 x 13 7 MD-MAXX036X /16 x MD-MAXX036X /8 x 13 7 MD-MAXX040X /8 x MD-MAXX040X /8 x MD-MAXX040X /4 x 13 7 MD-MAXX048X /4 x MD-MAXX048X /4 x MD-MAXX048X /8 x 13 7 MD-MAXX056X13 $ /8 x MD-MAXX056X x 13 7 MD-MAXX100X x MD-MAXX100X x MD-MAXX100X /8 x 13 7 MD-MAXX108X /8 x MD-MAXX108X /4 x 15 9 MD-MAXX116X /4 x MD-MAXX116X /8 x MD-MAXX124X /2 x 15 9 MD-MAXX132X /2 x MD-MAXX132X SLOT (SDS-MAXX ) BITS FIT THE FOLLOWING HAMMERS BOSCH HILTI HILTI TE-54 TE 52, 60 SDS-MAX TE-Y (New) TE 72, 92

21 MASONRY (SPLINE ) HAMMER DRILLS ICS USA/EUR HEAVY DUTY SPLINE PARABOLIC FLUTE MAS-19 Carbide Tipped Spline Shank Drive Masonry Hammer Drills with a single cutting edge are designed for use with splinedrive rotary hammers. Spline drive hammer bits have 12 splines cut into the 3/4" diameter shank to ensure a positive fit between the bit and the bit holder on a spline drive rotary hammer which makes possible the most power transmission to the cutting edge for high speed drilling of large diameter holes in concrete, masonry and stone. 3/8 x 12 6 MD-S024X12 $ /8 x MD-S024X /2 x 12 6 MD-S032X /2 x MD-S032X /2 x MD-S032X /2 x MD-S032X /16 x 12 6 MD-S036X /8 x 12 6 MD-S040X /8 x MD-S040X /8 x MD-S040X /8 x MD-S040X /16 x 12 6 MD-S044X /4 x 12 6 MD-S048X /4 x MD-S048X /4 x MD-S048X /4 x MD-S048X /8 x 12 6 MD-S056X /8 x MD-S056X /8 x MD-S056X /8 x MD-S056X36 $ x 12 6 MD-S100X x MD-S100X x MD-S100X x MD-S100X /8 x MD-S108X /8 x MD-S108X /8 x MD-S108X /4 x MD-S116X /4 x MD-S116X /4 x MD-S116X /8 x MD-S124X /8 x MD-S124X /8 x MD-S124X /2 x MD-S132X /2 x MD-S132X /2 x MD-S132X x MD-S200X x MD-S200X SPLINE DRIVE BITS (MD-S) FIT THE FOLLOWING HAMMERS AEG B&D BOSCH HITACHI METABO MILWAUKEE PH DH 38 YA RH PH-350 D DS 50 SB RH PH-350 HD DS 50 SB RH 99X 5343 PH DH 384 A PH PHD PHD PH-240 D KANGO MAKITA ITT PHILIPS PORTER CABLE RAMSET RYOBI 637 S HR ED 382 P 950 S 445 RED HEAD 747-2

22 MAS-20 MASONRY (SPLINE ) HAMMER DRILLS SPLINE MULTI CUTTER DESIGN CROSS HEAD POINT PARABOLIC FLUTE Carbide Tipped Spline Shank Drive Masonry Hammer Drills with 4 cross cutting edges are designed for use with spline drive rotary hammers. The 4 cross cutting edges pulverize the material to be drilled better and quicker than single edge hammer bits. Spline drive hammer bits have 12 splines cut into the 3/4" diameter shank to ensure a positive fit between the bit and the bit holder on a spline drive rotary hammer which makes possible the most power transmission to the cutting edge for high speed drilling of large diameter holes in concrete, masonry and stone. 3/4 x 12 6 MD-SX048X12 $ /4 x MD-SX048X /4 x MD-SX048X /8 x 12 6 MD-SX056X /8 x MD-SX056X /8 x MD-SX056X x 12 6 MD-SX100X x MD-SX100X x MD-SX100X /8 x MD-SX108X /8 x MD-SX108X23 $ /4 x MD-SX116X /4 x MD-SX116X /8 x MD-SX124X /2 x MD-SX132X /2 x MD-SX132X /8 x MD-SX140X /4 x MD-SX148X x MD-SX200X SPLINE DRIVE BITS (MD-SX) FIT THE FOLLOWING HAMMERS AEG B&D BOSCH HITACHI METABO MILWAUKEE PH DH 38 YA RH PH-350 D DS 50 SB RH PH-350 HD DH 384 A RH 99X 5343 PH PH PHD PHD PH-240 D KANGO MAKITA ITT PHILIPS PORTER CABLE RAMSET RYOBI 637 S HR ED 382 P 950 S 445 RED HEAD 747-2

23 A TAPER MASONRY HAMMER BITS MAS-21 A TAPER PARABOLIC FLUTE Carbide Tipped "A" Taper Shank Masonry Hammer Bits are designed to fit into "A" taper chuck adapter which allow "A" taper shank masonry hammer bits to be used with almost any current or discontinued model hammer drill. They are manufactured with a taper of 1" in 20" and are intended for drilling holes from 3/16" to 7/8" in concrete, masonry and stone. They are also known as Taper Shank Rotary Hammer Drill Bits. 3/16 x 4 1-3/4 MD-A012X04 $ /16 x 6 3-1/2 MD-A012X /4 x 6 3-1/2 MD-A016X /4 x MD-A016X /16 x 4 1-3/4 MD-A020X /16 x 6 3-1/2 MD-A020X /16 x 9 6 MD-A020X /8 x 6 3-1/2 MD-A024X /8 x 9 6 MD-A024X /8 x 12 9 MD-A024X /8 x MD-A024X /8 x MD-A024X /16 x 6 3-1/2 MD-A028X /2 x 6 3-1/2 MD-A032X /2 x 9 6 MD-A032X /2 x 12 9 MD-A032X /2 x MD-A032X /16 x /2 MD-A036X06 $ /16 x 9 6 MD-A036X /8 x MD-A040X /8 x 9 6 MD-A040X /8 x 12 9 MD-A040X /8 x MD-A040X /16 x MD-A044X /16 x 9 5 MD-A044X /4 x 5-1/2-6 3 MD-A048X /4 x 9 6 MD-A048X /4 x MD-A048X /32 x 9 7 MD-A054X /8 x 6 4 MD-A 056X /8 x 9 6 MD-A056X /8 x 12 8 MD-A056X x 9 6 MD-A100X B TAPER MASONRY HAMMER BITS B TAPER PARABOLIC FLUTE Carbide Tipped "B" Taper Shank Masonry Hammer Bits are designed to fit into "B" taper chuck adapter which allow "B" taper shank masonry hammer bits to be used with almost any current or discontinued model hammer drill. They are manufactured with a taper of 1" in 10" and are intended for drilling holes from 1/2" to 1-1/4" in concrete, masonry and stone. They are also known as Taper Shank Rotary Hammer Drill Bits. 1/2 x 9 6 MD-B032X09 $ /2 x 12 9 MD-B032X /2 x MD-B032X /2 x MD-B032X /16 x 9 6 MD-B036X /16 x MD-B036X /8 x 9 6 MD-B040X /8 x MD-B040X /8 x MD-B040X /8 x MD-B040X /16 x 9 6 MD-B044X /16 x MD-B044X /4 x 9 6 MD-B048X09 $ /4 x MD-B048X /4 x MD-B048X /32 x 9 7 MD-B054X /8 x 9 6 MD-B056X /8 x MD-B056X x 9 6 MD-B100X x MD-B100X /8 x 9 6 MD-B108X /8 x MD-B108X /4 x 9 6 MD-B116X /4 x MD-B116X

24 MAS-22 ICS USA TAPER CHUCK ADAPTERS ADAPTERS FOR A AND B TAPER MASONRY DRILLS Taper chuck adapters allow you to use: A or B taper shank masonry bits with almost any make of electric hammer drill. Each shank configuration will fit the hammer drill model numbers listed. A drift pin is included with each adapter. A TAPER B TAPER FITS HAMMER MODEL ITEM NO. ITEM NO. Skil 706, 707, 708 Skil 1706 B & D 5040, 5049 AT-706 $43.68 Rockwell 600, 601 Ramset 620 Skil 717 B & D 717, 718, 719 AT-717 BT B & D 5045, 5050 B & D 5046 Skil 726 Milw 5300, 5310 AT-726 BT Milw 5305, 5315 Skil 728, 731, 732, 628 Rockwell 602, 605, 606 Rockwell 1602 AT-728 BT B & D 5048 Milw 5325, 5326 Miller Falls SP499K Skil 736 BT Phillips 747, 700 Bosch AT-747 BT Metabo RH 90, 65 Ramset 330 AT-RAM BT-RAM Fits all popular 4 slot power tools. See pages AT-SDS BT-SDS & 163 for complete listing. Fits all popular spline drive power tools. See pages 162 & 163 for AT-Spline BT-Spline complete listing. Hilti TE 52, 60, 70, 92 AT-TE60 BT-TE Wacker AT-Wacker BT-Wacker Bosch 11216, SDS-MAX Hilti TE 64, TE-Y Hilti TE 52, 60 AT-MAX Hilti TE 72, 92 Important: Adapters are designed for intermittent use. A power loss of 10-15% and increased bit wear of 15-20% will result when using adapters.

25 MASONRY (9/16" HEX ) HAMMER DRILLS MAS-23 SKIL 728 HEX WIDE SPIRAL Carbide Tipped Heavy Duty 9/16" Hex Shank Masonry Hammer Drills, commonly classified as the Skil 728 Hex Shank, are designed to fit the following 9/16" hex drive rotary hammers: Skil 628,728, 731, 731, 732, 1760 Black and Decker 5048 Rockwell 602, 1602, 606, 616 Milwaukee 5325, 5326 Miller Falls SP 499K 9/16" Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 3/8" to 1-1/2" in concrete, masonry and stone. 3/8 x 12 6 MD X12 $ /16 x /2 MD X /2 x /2 MD X /16 x 13 7 MD X /8 x /2 MD X /8 x /2 MD X /8 x /2 MD X /16 x 13 7 MD X /8 x /2 MD X /8 x /2 MD X /8 x /2 MD X x 12 7 MD X12 $ x /2 MD X x MD X /8 x /2 MD X /8 x MD X /4 x /2 MD X /4 x MD X /8 x /2 MD X /8 x MD X /2 x /2 MD X /2 x MD X MASONRY (3/8" HEX ) HAMMER DRILLS SKIL 706 HEX WIDE SPIRAL Carbide Tipped Heavy Duty 3/8" Hex Shank Masonry Hammer Drills, commonly referred to as the Skil 706 hex shank, are designed for the following 3/8" hex drive rotary hammers: Black and Decker 5040, 5048 Rockwell 600, 601 Milwaukee M06 Skil 706, 707, 708, 1706, 511 Ramset 620 3/8" hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 3/8" to 7/8" in concrete, masonry and stone. 3/8 x 9 5 MD X09 $ /8 x MD X /16 x 9 5 MD X /2 x 10 6 MD X /2 x MD X /2 x MD X /8 x 10 6 MD X /8 x 12 8 MD X /8 x MD X16 $ /8 x MD X /16 x 10 6 MD X /4 x 10 6 MD X /4 x MD X /32 x 10 6 MD X /8 x 10 6 MD X /8 x MD X

26 MAS-24 MASONRY (7/16" HEX ) HAMMER DRILLS BLACK & DECKER 717 HEX WIDE SPIRAL Carbide Tipped Heavy Duty 7/16" Long Hex Shank Masonry Hammer Drills, commonly referred to as the Black and Decker 717 hex shank, are designed for the following 7/16" hex drive rotary hammers: Black and Decker 717, 718, 719, 5045, 5046, /16" long hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 1/2" to 1-1/2" in concrete, masonry and stone. 1/2 x 10 3 MD-717L-032X10 $ /2 x 16 9 MD-717L-032X /2 x MD-717L-032X /8 x 10 3 MD-717L-040X /8 x MD-717L-040X /8 x MD-717L-040X /16 x 12 5 MD-717L-044X /4 x 10 3 MD-717L-048X /4 x 16 9 MD-717L-048X /4 x MD-717L-048X /8 x 12 5 MD-717L-056X /8 x MD-717L-056X22 $ x 12 5 MD-717L-100X x MD-717L-100X /8 x 12 5 MD-717L-108X /8 x MD-717L-108X /4 x 12 5 MD-717L-116X /4 x MD-717L-116X /8 x 12 5 MD-717L-124X /8 x MD-717L-124X /2 x 12 5 MD-717L-132X /2 x MD-717L-132X MASONRY (7/16" HEX ) HAMMER DRILLS SKIL 717 HEX WIDE SPIRAL Carbide Tipped Heavy Duty 7/16" Short Hex Shank Masonry Hammer Drills, commonly referred to as the Skil 717 hex shank, are designed for the following 7/16" hex drive rotary hammers: Skil 717, 718, 719, /16" short hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 1/2" to 1-1/2" in concrete, masonry and stone. 1/2 x 10 3 MD X10 $ /2 x 16 9 MD X /2 x MD X /8 x 10 3 MD X /8 x MD X /8 x MD X /16 x 12 5 MD X /4 x 10 3 MD X /4 x 16 9 MD X /4 x MD X /8 x 12 5 MD X /8 x MD X22 $ x 12 5 MD X x MD X /8 x 12 5 MD X /8 x MD X /4 x 12 5 MD X /4 x MD X /8 x 12 5 MD X /8 x MD X /2 x 12 5 MD X /2 x MD X NOTE ICS Cutting Tools will continue to offer Hex Shank (MD-700 Series) Masonry Drills for discontinued power tools as long as stock and demand exists. Some sizes may no longer be available and a minimum quantity may be required for that size.

27 MASONRY (9/16" HEX ) HAMMER DRILLS MAS-25 PHILLIPS 747 HEX WIDE SPIRAL Carbide Tipped Heavy Duty 9/16" Hex Shank Masonry Hammer Drills, commonly classified as the Phillips 747 Hex Shank, are designed to fit the following 9/16" hex drive rotary hammers. Phillips , 700 Bosch Metabo RH 65, 90, 90x 9/16" Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 7/16" to 1-1/2" in concrete, masonry and stone. 7/16 x 10 6 MD X10 $ /2 x 10 6 MD X /16 x 12 8 MD X /8 x 10 6 MD X /8 x MD X /8 x MD X /16 x 12 8 MD X /4 x 10 6 MD X /4 x MD X /4 x MD X /8 x 10 6 MD X10 $ /8 x MD X /8 x MD X x 10 6 MD X x MD X /8 x 12 8 MD X /8 x MD X /4 x MD X /2 x MD X MASONRY (3/4" HEX ) HAMMER DRILLS SKIL 736 HEX WIDE SPIRAL Carbide Tipped Heavy Duty 3/4" Hex Shank Masonry Hammer Drills, commonly classified as the Skil 736 Hex Shank, are designed to fit the following 3/4" hex drive rotary hammers. Skil 736, 1770 Stanley HD20, 45 3/4" Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 3/4" to 2" in concrete, masonry and stone. 3/4 x MD X24 $ /4 x MD X /8 x MD X x MD X x MD X /8 x MD X24 $ /4 x MD X /4 x MD X /2 x MD X x MD X

28 MAS-26 MASONRY (21.0mm HEX ) HAMMER DRILLS KANGO 950 HEX PARABOLIC FLUTE Carbide Tipped Heavy Duty 21.0mm Hex Shank Masonry Drills, commonly classified as the Kango 950 Hex Shank, are designed to fit the following 21.0mm hex drive rotary hammers: Kango 950, 900, 1400, 450x, 950x Hitachi DH505A, H555A Makita HR5000R/K, HM1200K Ryobi CH 485PK 21.0mm hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 5/8" to 1-3/4" in concrete, masonry and stone. 5/8 x 14 7 MD X14 $ /8 x MD X /8 x MD X /4 x MD X /8 x 14 7 MD X /8 x MD X x 14 7 MD X x MD X /8 x 14 7 MD X14 $ /8 x MD X /4 x 14 7 MD X /4 x MD X /2 x 14 7 MD X /2 x MD X /4 x MD X MASONRY (19.0mm HEX ) HAMMER DRILLS KANGO 637 HEX PARABOLIC FLUTE Carbide Tipped Heavy Duty 19.0mm Hex Shank Masonry Drills, commonly classified as the Kango 637 Hex Shank, are designed to fit the following 19.0mm hex drive rotary hammers: Kango 500,501, 625, 627, 637, 750, 750x Rockwell 605, 607, 637, 750, 750x, mm hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 5/8" to 1-3/4" in concrete, masonry and stone. 1/2 x MD X23 $ /8 x 13 7 MD X /8 x MD X /8 x MD X /4 x MD X /8 x 13 7 MD X13 $ /8 x MD X x MD X /4 x MD X

29 ICS USA ELECTRIC HAMMER CHISELS HEAVY DUTY MAS-27 FORGED STEEL ICS Electric Hammer Chisels are available in a variety of shank styles. The descriptions below will assist the hammer drill user in making a selection for their specific application. STYLE SPLINE (5/8" ROUND HEX) SDS-PLUS BOSCH SDS-MAX HEX-DEMOLITION (3/4" HEX) HEX-BREAKER (1-1/8" HEX) FITS/APPLICATION Fits all makes of Spline Drive Hammers. Round hex shank works effectively in Spline Drive machines made with and without rotation / hammer only switches. Fits all popular 4 slot power tools. Operator simply moves selector switch to percussion only mode to use. Fits directly into new Bosch SDS-MAX Hammers and Hilti Hammers with large 2 slot bit locking systems. Fits Bosch Models and Fits Bosch Model Hex Shank Chisels come with internal locks for Demolition Hammers and External Collars for Pneumatic Hammers. NOMINAL DESCRIPTION STYLE ITEM NO. (PT.) 12 SPLINE EHC-BP-12S $24.08 (PT.) 18 SPLINE EHC-BP-18S (PT.) 10 SDS-PLUS EHC-BP-10SDS BULL (MOIL) POINT Electric Hammer Bull Point Chisels are designed for light demolition work and starting holes in concrete slabs, brick, mortar, slate etc... They are also known as Electric Hammer Moil Point Chisels. FLAT (COLD) CHISEL Electric Hammer Flat Chisels are designed for edging, chipping, scaling or channeling concrete, masonry or brick. They are also known as Electric Hammer Cold Chisels. SCALING CHISEL Electric Hammer Scaling Chisels are designed for removing scale, rust, concrete and weld spatter. They are also known as Electric Hammer Wide Chisels. (PT.) 12 SDS-MAX EHC-BP-12MAX (PT.) 16 SDS-MAX EHC-BP-16MAX (PT.) 12 HEX (3/4) EHC-BP-12HD (PT.) 18 HEX (3/4) EHC-BP-18HD (PT.) 12 HEX (1-1/8) EHC-BP-12HB (PT.) 18 HEX (1-1/8) EHC-BP-18HB SPLINE EHC-FC-12S SPLINE EHC-FC-18S SDS-PLUS EHC-FC-10SDS SDS-MAX EHC-FC-12MAX SDS-MAX EHC-FC-16MAX HEX (3/4) EHC-FC-12HD HEX (3/4) EHC-FC-18HD HEX (1-1/8) EHC-FC-12HB HEX (1-1/8) EHC-FC-18HB /2 12 SPLINE EHC-SC-12S-A /2 18 SPLINE EHC-SC-18S-A SPLINE EHC-SC-12S-B SPLINE EHC-SC-18S-B /2 10 SDS-PLUS EHC-SC-10SDS-A SDS-MAX EHC-SC-12MAX SDS-MAX EHC-SC-16MAX /2 12 HEX (3/4) EHC-SC-12HD-A /2 18 HEX (3/4) EHC-SC-18HD-A HEX (3/4) EHC-SC-12HD-B HEX (3/4) EHC-SC-18HD-B 39.06

30 MAS-28 ELECTRIC HAMMER CHISELS FORGED STEEL NOMINAL DESCRIPTION STYLE ITEM NO. SLOTTING TOOL Electric Hammer Slotting Chisels are designed for slotting and cutting web between drilled holes in concrete to make larger openings. Alternately known as an Electric Hammer Slotting Tool. MORTAR (SEAM) CHISEL Electric Hammer Mortar Chisels are for removing old mortar between bricks before tuck pointing or caulking. They can also be used to cut narrow channels or to remove bricks in wall for installing insulation. They are also known as Electric Hammer Seam Chisels or Brick Removing Chisels. CLAY SPADE 5-1/2" Electric Hammer Clay Spade Chisels are designed for digging out clay, hard packed gravel, dirt, shale etc... They are primarily used for landscaping and are not for use in concrete. ASPHALT CUTTER 5" Electric Hammer Asphalt Cutter Chisels are designed for cutting or breaking up asphalt or hard ground. They are primarily used for road maintenance and are not for use in concrete. They are also known as Tarmac Chisels. GROUND ROD DRIVER Electric Hammer Ground Rod Drivers are designed for driving 5/8 or 3/4 electrical grounding rods into earth near the edge of structure foundation or for installing parking bumpers. BUSHING TOOL (1 PC TOOL) The 1 Piece Electric Hammer Bushing Tool is a solid forged hammer chisel designed for roughing up concrete and asphalt prior to resurfacing. May be used to produce a rough exterior finish. BUSHING TOOL (2 PC TOOL KIT) The 2 Piece Electric Hammer Bushing Tool has a replaceable tool head and tool shank. It is designed for roughing up concrete and asphalt prior to resurfacing. It may also be used to produce a rough exterior finish. BUSHING TOOL HEADS 1-1/8 12 SPLINE EHC-ST-12S $ /4 12 SDS-MAX EHC-ST-12MAX /8 12 HEX (3/4) EHC-ST-12HD /8 15 SPLINE EHC-MC-15S /8 12 SDS-MAX EHC-MC-12MAX /8 15 HEX (3/4) EHC-MC-15HD /2 18 SPLINE EHC-CS-18S /2 16 SDS-MAX EHC-CS-16MAX /2 18 HEX (3/4) EHC-CS-18HD /2 16 HEX (1-1/8) EHC-CS-16HB HEX (1-1/8) EHC-AC-16HB HEX (3/4) EHC-AC-16HD SDS-MAX EHC-AC-16MAX /8-3/4 11 SPLINE EHC-GRD-11S /8-3/4 11 SDS-MAX EHC-GRD-11MAX /8-3/4 11 HEX (3/4) EHC-GRD-11HD /2 x 1-1/2 8 SPLINE EHC-BT-S /2 x 1-1/2 10 MAX EHC-BT-MAX /2 x 1-1/2 8 HEX (3/4) EHC-BT-HD /4 x 1-1/4 11-1/2 SDS-PLUS EHC-BT-SDS /2 x 1-1/2 8 SPLINE EHC-BTK-S /2 x 1-1/2 10 SDS-MAX EHC-BTK-MAX /2 x 1-1/2 8 HEX (3/4) EHC-BTK-HD /2 x 1-1/2 - FITS ALL EHC-BTH S Electric Hammer Bushing Tool Heads are designed to fit any style bushing tool shank or stem, They are also known as Bushing Hammer Tools. BUSHING TOOL (STEMS) Electric Hammer Bushing Tools Shanks are designed to fit all Spline, SDS-MAX, or 3/4 Hex Drive Hammer Drills. They are also known as Electric Hammer Bushing Tool Stems or Bushing Drivers. NOTE: Other styles and sizes available on request. - 8 SPLINE EHC-BTS-8S SDS-MAX EHC-BTS-10MAX HEX (3/4) EHC-BTS-8HD All ICS Electric Hammer Chisels are heat treated for Heavy Duty use and can be easily maintained using simple hand grinding.