LED WALL WASHERS SPECIFICATIONS & INSTALLATION GUIDE

Transcription

1 LED WALL WASHERS SPECIFICATIONS & INSTALLATION GUIDE

2 ContenTS: Brief specifications LED WALL WASHER WWF LED WALL WASHER WWB LED WALL WASHER WWS LED WALL WASHER WWS LED WALL WASHER WWS V LED WALL WASHER WWT V LED WALL WASHER WWT V LED WALL WASHER WWT Installation GUIDE WWS, WWF, WWB SERIES HARD WIRE...12 WWS, WWF, WWB SERIES PLUG & PLAY...13 WWT SERIES HARD WIRE...14 WWT SERIES PLUG & PLAY...15

3 IMPORTANT SAFETY INSTRUCTIONS When installing or using this product, basic safety precautions should always be followed including the following: 1. Read all instructions before attempting to install this product. 2. Ensure main power is off before installing or wiring this product. 3. Ensure correct voltage is being used for this product. 4. Disconnect electrical power before adding to or changing the configuration of this product. 5. Fixtures must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulation.

4 led Wall WaSHer WWF /2" 10-5/8" 7-3/4" 3" SpeCifiCationS Model WWf pp 60 W30 WWf pp 60 W50 WWf pp 60 rgb WWf pp 60 awb led Quantity 48 Wattage 56 W lumens 2500 lm 3300 lm efficacy 44.6 lm/w 58.9 lm/w 33.8 lm/w 42.1 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue Beam angle 120 x 60 Cri 75 N/A Voltage lamp life Dimensions Weight Housing finish V AC 50,000 hours 12 1/2"L 10 5/8"H 7 3/4"D 11.5 lbs / 5.2 kg Aluminum Z Bronze (Standard) operating temperature -4 F 113 F / -20 C 45 C operating Humidity Mounting Maximum run environment Certifications Warranty 10% - 90% RH Bracket and handle. Steel Yoke with bolt holes and screw holes. 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWf pp - Plug & Play x120 W K Z - Bronze HW - Hard Wire* W K a - Aluminum* rgb B - Black* awb W - White* * Custom options Consult factory example: WWf pp 60 W30 Z 4

5 LED WALL WASHER WWB /2" 7-1/8" 11-1/2" 6-3/8" SPECIFICATIONS Model WWB PP 30 W30 WWB PP 30 W50 WWB PP 30 RGB WWF PP 30 AWB LED Quantity 36 Wattage Lumens 1500 lm 2000 lm Efficacy 37.5 lm/w 50 lm/w 28.6 lm/w 35.8 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue CRI 75 N/A 40W Beam Angle* 30 Voltage Lamp Life Dimensions Weight Housing Finish V AC 50,000 hours 13 1/2" L x 11 1/2" H x 6 3/8" D 10 lbs / 4.5kg Aluminum Z Bronze (Standard) Operating Temp -4 F 113 F / -20 C 45 C Operating Humidity DMX Input Mounting Maximum Run Environment Certifications Warranty 10% - 90% RH 3 Pin Washer DMX Plug Screw holes on steel baseplate with integral 24V DC 350mA power supply 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ORDERING INSTRUCTIONS MODEL WIRING TYPE BEAM ANGLE CCT FINISH WWB PP - Plug & Play W K Z - Bronze * Custom options Consult factory HW - Hard Wire* * W K A - Aluminum* * RGB B - Black* AWB W - White* Example: WWB PP 30 W30 Z 5

6 led Wall WaSHer WWS /8" 4-1/2" 2-1/4" 2-3/4" 15-1/4" SpeCifiCationS Model WWS pp 30 W30 WWS pp 30 W50 WWS pp 30 rgb WWS pp 30 awb led Quantity 12 Wattage lumens efficacy 58.3 lm/w 74.6 lm/w 42.6 lm/w 53.3 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue 14W Beam angle* 30 Cri 75 N/A Voltage lamp life Dimensions Weight Housing finish V AC 50,000 hours 16 3/8" L x 2 3/4" W x 4 1/2" H 4 lbs / 1.8 kg Aluminum Z Bronze (Standard) operating temp -22 F 104 F / -30 C 40 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 Pin Washer DMX male Plug Steel Yoke with bolt holes and screw holes 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWS pp - Plug & Play W K Z - Bronze HW - Hard Wire* * W K a - Aluminum* * rgb B - Black* awb W - White* * Custom options Consult factory example: WWS pp 30 W30 Z 6

7 led Wall WaSHer WWS " 4-1/2" 2-1/4" 2-3/4" 30-7/8" SpeCifiCationS Model WWS pp 30 W30 WWS pp 30 W50 WWS pp 30 rgb WWS pp 30 awb led Quantity 24 Wattage lumens efficiency 39.3 lm/w 53.6 lm/w 30.6 lm/w lm/w Color temperature 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue Cri 75 N/A 28W Beam angle* 30 Voltage lamp life Dimensions Weight Housing finish V AC 50,000 hours 32" L x 2 3/4" W x 4 1/2" H 5.5 lbs / 2.5 kg Aluminum Z Bronze (Standard) operating temperature -22 F 104 F / -30 C 40 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 Pin Washer DMX male Plug Steel Yoke with bolt holes and screw holes 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWS pp - Plug & Play W K Z - Bronze HW - Hard Wire* * W K a - Aluminum* * rgb B - Black* awb W - White* * Custom options Consult factory example: WWS pp 30 W30 Z 7

8 led Wall WaSHer WWS /8" 4-1/2" 2-1/4" 2-3/4" 46-3/4" SpeCifiCationS Model WWS pp 30 W30 WWS pp 30 W50 WWS pp 30 rgb WWS pp 30 awb led Quantity 36 Wattage lumens efficacy 33.3 lm/w 44.4 lm/w 25.4 lm/w 31.8 lm/w Color temperature 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue 45W Beam angle* 30 Cri 75 N/A Voltage lamp life Dimensions Weight Housing finish V AC 50,000 hours 47 7/8" L x 2 3/4" W x 4 1/2" H 8.8 lbs / 4 kg Aluminum Z Bronze (Standard) operating temp -22 F 104 F / -30 C 40 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 Pin Washer DMX male Plug Steel Yoke with bolt holes and screw holes 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWS pp - Plug & Play W K Z - Bronze HW - Hard Wire* * W K a - Aluminum* * rgb B - Black* awb W - White* * Custom options Consult factory example: WWS pp 30 W30 Z 8

9 24V led Wall WaSHer WWT /2"L 6-3/4"W 13-3/8" 2-1/8" 3-1/4" 5-3/4" 5-1/4"H 1-7/8" SpeCifiCationS Model WWt pp 30 W30 WWt pp 30 W50 WWt pp 30 rgb WWt pp 30 awb led Quantity Wattage 12 (Bridgelux) lumens efficacy lm/w 50 lm/w Color 3000K 3500K 5000K 5500K Red, Green, Blue Amber, White, Blue 15W Beam angle* 30 Voltage efficiency lamp life Dimensions Weight Housing finish 24V DC 0.9 PF 50,000 hours 15 1/2" L x 6 3/4" W x 5 1/4" H 6.6 lb Aluminum Z Bronze (Standard) operating temp -4 F 113 F / -20 C 45 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 pin Jesco DMX plug Surface Mount 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWt pp - Plug & Play W K Z - Bronze HW - Hard Wire* * W K a - Aluminum* * rgb B - Black* awb W - White* * Custom options Consult factory example: WWt pp 30 W30 Z 9

10 24V led Wall WaSHer WWT /8"L 5-1/2"H 7-3/8"W SpeCifiCationS Model WWt pp 30 W30 WWt pp 30 W50 WWt pp 30 rgb WWt pp 30 awb led Quantity Wattage 36 (Bridgelux) 105W lumens 5100 lm 6000 lm efficacy 48.6 lm/w 57.1 lm/w 32.7 lm/w 40.8 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue Beam angle* 30 Voltage 24V DC efficiency PF 0.60 lamp life Dimensions Weight Housing finish 50,000 hours 23 5/8" L x 7 3/8" W x 5 1/2" H 11 lbs / 5 kg Aluminum Z Bronze (Standard) operating temp -4 F 113 F / -20 C 45 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 pin Jesco DMX plug Surface Mount 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWt pp - Plug & Play W K Z - Bronze HW - Hard Wire* * W K a - Aluminum* * rgb B - Black* awb W - White* * Custom options Consult factory example: WWt pp 30 W30 Z 10

11 24V led Wall WaSHer WWT /8"L 5-1/2"H 7-3/8"W SpeCifiCationS Model WWt pp 30 W30 WWt pp 30 W50 WWt pp 30 rgb WWt pp 30 awb led Quantity Wattage 72 (Bridgelux) 176W lumens 7100 lm 8200 lm efficacy 40.3 lm/w 46.6 lm/w 26.6 lm/w 33.3 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue Beam angle* 30 Voltage 24V DC efficiency PF 0.60 lamp life Dimensions Weight Housing finish 50,000 hours 47 3/8" L x 7 3/8" W x 5 1/2" H 20.3 lbs / 9.2 kg Aluminum Z Bronze (Standard) operating temp -4 F 113 F / -20 C 45 C operating Humidity 10% - 90% RH DMX input Jesco DMX 3-pin plug 3 pin Washer DMX plug Mounting Maximum run environment Certifications Warranty Surface Mount 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; a Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWt pp - Plug & Play W K Z - Bronze HW - Hard Wire* * W K a - Aluminum* * rgb B - Black* awb W - White* * Custom options Consult factory example: WWt pp 30 W30 Z 11

12 WWS, WWF, WWB SerieS HARD WIRE 1. Configure design and lay out the system before attempting to install this product. Note A DMX controller is required to operate Wall Washer fixtures. Additional DMX adapter cables may be required. 2. Set DMX Address Locate the DMX addressing interface on the fixture. Power the fixture. Select a DMX address ( ). Each address consists of 3 channels (R-G-B or A-W-B). To control fixtures individually, assign a unique DMX address per fixture. To control fixtures at the same time, assign the same DMX for each fixture. 3. ensure Main POWER IS off. 4. Install Fixtures Determine locations on the mounting surface according to the desired design and layout. Ensure fixtures are installed within the maximum run length of DMX cable (1,000 feet or 300 feet for CAT5 cable). DMX wiring must be installed in a continuous run (daisy chained). Connect main power wires to Washer fixture. 5. Connect Fixtures Connect fixtures using DMX cable. Ensure a tight connection is made by tightening the lock nut. For harsh environments you may use a silicon compound to seal the connectors. For hardwiring, use weatherproof boxes and covers as needed (supplied by ). 6. Connect Controller Run DMX cable from the controller to the first fixture. If no controller is connected and the DMX address is set to 001, the fixture will enter into the default test mode and cycle colors. See Controller specification sheet for more details. 7. Run System Turn the power on. Check all fixtures to make sure they are running properly. If fixtures are not running properly, check all connections and retighten. Optional A DMX Distribution Amplifier is required for multiple runs (star wiring) or when installing more than 16 fixtures. Max. 16 fixtures WWB, WWF, or WWS WWB, WWF, or WWS WWB, WWF, or WWS LC-DMX-AMP2 DMX CONTROLLER* 2-port DMX Distribution WWB, WWF, or WWS Main Power * See controller specification sheet for more details. 12

13 WWS, WWF, WWB SERIES PLUG & PLAY 1. Configure design and lay out the system before attempting to install this product. Note A DMX controller is required to operate Wall Washer fixtures. Additional DMX adapter cables may be required. 2. Set DMX Address Locate the DMX addressing interface on the fixture. Power the fixture. Select a DMX address ( ). Each address consists of 3 channels (R-G-B or A-W-B). To control fixtures individually, assign a unique DMX address per fixture. To control fixtures at the same time, assign the same DMX for each fixture. 3. ensure Main POWER IS off. 4. Install Fixtures Determine locations on the mounting surface according to the desired design and layout. Ensure fixtures are installed within the maximum run length of DMX cable (1,000 feet or 300 feet for CAT5 cable). DMX wiring must be installed in a continuous run (daisy chain. 5. Connect Fixtures Connect fixtures using DMX cable. Ensure a tight connection is made by tightening the lock nut. For harsh environments you may use a silicon compound to seal the connectors. For hardwiring, use weatherproof boxes and covers as needed (supplied by ). 6. Connect Controller Run DMX cable from the controller to the first fixture. If no controller is connected and the DMX address is set to 001, the fixture will enter into the default test mode and cycle colors. See Controller specification sheet for more details. 7. Run System Turn the power on. Check all fixtures to make sure they are running properly. If fixtures are not running properly, check all connections and retighten Optional A DMX Distribution Amplifier is required for multiple runs (star wiring) or when installing more than 16 fixtures. DMX Adressing Interface Max. 16 fixtures WWB, WWF or WWS WWB, WWF or WWS WWB, WWF or WWS LC-DMX-AMP1 LC-DMX-AMP2 1-port DMX Distribution To DMX CONTROLLER* 2-port DMX Distribution AC AC AC WWB, WWF or WWS DL-PS-XX/24-JB DL-PS-XX/24-JB AC AC AC * See controller specification sheet for more details. 13

14 WWT SERIES HARD WIRE 1. Configure design and lay out the system before attempting to install this product. Note A DMX controller is required to operate Wall Washer fixtures. Additional DMX adapter cables may be required. 2. Install Power Supply Determine location of the power supply. Connect low voltage wires from power supply to the fixture. Ensure correct polarity is connected (positive to positive, negative to negative). 3. Set DMX Address Locate the DMX addressing interface on the fixture. Power the fixture. Select a DMX address ( ). Each address consists of 3 channels (R-G-B or A-W-B). To control fixtures individually, assign a unique DMX address per fixture. To control fixtures at the same time, assign the same DMX for each fixture. 4. ensure Main POWER IS off. cable). DMX wiring must be installed in a continuous run (daisy chained). Connect main power wires to Washer fixture. Optional: A DMX Distribution Amplifier is required for multiple runs (star wiring) or when installing more than 16 fixtures. Connect Fixtures Connect fixtures using DMX cable. Ensure a tight connection is made by tightening the lock nut. For harsh environments you may use a silicon compound to seal the connectors. For hardwiring, use weatherproof boxes and covers as needed (supplied by ). See Controller specification sheet for more details. 6. Connect Controller Run DMX cable from the controller to the first fixture. If no controller is connected and the DMX address is set to 001, the fixture will enter into the default test mode and cycle colors. 5. Install Fixtures Determine locations on the mounting surface according to the desired design and layout. Ensure fixtures are installed within the maximum run length of DMX cable (1,000 feet or 300 feet for CAT5 7. Run System Turn the power on. Check all fixtures to make sure they are running properly. If fixtures are not running properly, check all connections and retighten. Max. 16 fixtures WWT WWT WWT DMX CONTROLLER* LC-DMX-AMP2 2-port DMX Distribution 24V 24V 24V 24V WWT Main Power 24V * See controller specification sheet for more details. 14

15 WWT SERIES PLUG & PLAY 1. Configure design and lay out the system before attempting to install this product. Note A DMX controller is required to operate Wall Washer fixtures. Additional DMX adapter cables may be required. 2. Install Power Supply Determine location of the power supply. Connect low voltage wires from power supply to the power connector (WW-PC- HW/DC-72). Ensure correct polarity is connected (positive to positive, negative to negative). Connect power connector to the Washer fixture. 3. Set DMX Address Locate the DMX addressing interface on the fixture. Power the fixture. Select a DMX address ( ). Each address consists of 3 channels (R-G-B or A-W-B). To control fixtures individually, assign a unique DMX address per fixture. To control fixtures at the same time, assign the same DMX for each fixture. 4. ensure Main POWER IS off. 5. Install Fixtures Determine locations on the mounting surface according to the desired design and layout. Ensure fixtures are installed within the maximum run length of DMX cable (1,000 feet or 300 feet for CAT5 cable). DMX wiring must be installed in a continuous run (daisy chained). Connect main power wires to Washer fixture. Optional: A DMX Distribution Amplifier is required for multiple runs (star wiring) or when installing more than 16 fixtures. Connect Fixtures Connect fixtures using DMX cable. Ensure a tight connection is made by tightening the lock nut. For harsh environments you may use a silicon compound to seal the connectors. For hardwiring, use weatherproof boxes and covers as needed (supplied by ). See Controller specification sheet for more details. 6. Connect Controller Run DMX cable from the controller to the first fixture. If no controller is connected and the DMX address is set to 001, the fixture will enter into the default test mode and cycle colors. 7. Run System Turn the power on. Check all fixtures to make sure they are running properly. If fixtures are not running properly, check all connections and retighten. Max. 16 WWT WWT WWT 24V DMX CONTROLLER* WW-PC-HW/DC-72 Main Power LC-DMX-AMP2 2-port DMX Distribution WW-PC-HW/DC-72 24V 24V 24V * See controller specification sheet for more details. WW-PC-HW/DC-72 WWT 24V WW-PC-HW/DC-72 15

16 NEw YORk CORPORATE OFFICES 6625 traffic avenue Glendale ny TEL TEL FAX LOS ANgELES 1100 Hatcher ave Suite a City of industry Ca TEL TEL FAX JESCOLIGHTING.COM 2011 JeSCo lighting