CD-8 PARTS MANUAL COLD DRINK VENDOR MODEL: November 1995 P/N

Transcription

1 CD-8 B MODEL COLD DRINK VENDOR MODEL: 3037 PARTS MANUAL November 1995 P/N

2 GENERAL INFORMATION: Welcome to Selectivend, Inc., we offer you three convenient ways to order replacement parts. If you have any questions when placing your order, please call and we ll be happy to assist you. Please provide the following information when placing your order: Quantity Required Part Number Shipping and Billing Address Description Preferred Method of Shipment Vendor Model Number Customer Account Number Serial Number MINIMUM ORDER $ You may wish to inquire on prices of parts at the time of your order. If you order less than the minimum, please check our catalog for other parts you may require to bring your order up to the $25.00 minimum order. OPEN ACCOUNT with approved credit. MASTER CARD - VISA - C.O.D. If you have any questions, please call and we will be happy to assist you. TO ORDER BY MAIL: You may place your requirements for replacement parts by providing the necessary information as requested above, and mailing your order to: Selectivend, Inc. P.O. Box North 10th Street Waukee, Iowa If you have any questions, call ( ), ask for Selectivend Parts and we will be happy to assist you. Order forms are available upon request from Selectivend, Inc. Or you may use your own purchase order form. TO ORDER BY FAX MACHINE: (515) You may call in your order for replacement parts. Ask for Selectivend Parts Department. Please provide the necessary information, as requested above, to allow us to provide you with prompt courteous service. If you have any questions, so indicate and we will be happy to assist you. RETURNS: RESTOCKING CHARGE 20%. A restocking charge of 20% will apply to merchandise accepted by Selectivend for return, except items processed as warranty. All items returned must be accompanied by a material return tag clearly stating the reason for return. Returns are to be shipped freight prepaid to Selectivend, Inc., 165 North 10th Street, Waukee, Iowa (Return tags are available upon request from Selectivend.) If you have any questions regarding returns, please call Selectivend, Inc. ( ), we will be happy to assist you. LIMITATION OF LIABILITY: Selectivend. Inc. Shall not be liable for any injury, loss or damage, whether direct, incidental or consequential arising out of the use of or the inability to use any part, parts or products sold by Selectivend, Inc. The remedies of the buyer set forth herein are exclusive, and the liability of Selectivend, Inc. With respect to any contract or sale or anything done in connection herewith, whether in connection therewith, whether in contract, in tort, under any warranty, or otherwise, shall not, except as expressly provided herein, exceed the price of the part, parts or products on which such liability is based. Any statements or representations about the parts or product, other than those contained herein, do not constitute warranties and shall not be relied on by the buyer and shall have no force of effect unless contained in a written agreement signed by officers of Selectivend. You may Fax your order for replacement parts by providing the necessary information as requested above to Selectivend, Inc. By using our fax, (515) TO ORDER BY PHONE: ( ) 1

3 FINAL ASSEMBLY 2

4 FINAL ASSEMBLY ITEM PART NUMBER QTY DESCRIPTION 1 1 CABINET ASSEMBLY - See Page # AIR BAFFLE LINE RETAINER A/R #8-18 X 1/2 PHIL HWH TEK REFRIGERATION SYSTEM - R134A - See Page # DOUBLE SERPENTINE CAN RACK - See Page # UPPER EJECTOR MECH - See Page # LOWER EJECTOR MECH - See Page # CAN SLIDE - UPPER CAN SLIDE MOTOR COVER CABINET HARNESS 13 1 COMPLETE DOOR ASSEMBLY - See Page # INNER DOOR ASSEMBLY - See Page # WIRE RETAINER R.F.I. LINE FILTER COLD CONTROL COVER DECAL BRACKET - THERMOSTAT #8-32 X 3/8 PHIL TH MS THERMOSTAT SHIELD THERMOSTAT SERVICE HARNESS #8 X 1/2 PHIL TH TYPE A SMS SINGLE SERPENTINE CAN RACK - See Page # /16-18 X 1¼ HH TAPTITE LOCK CYLINDER (W/2 KEYS) #8-18 X 3/8 PHIL PH TYPE B PARTS FURNISHED IN SERVICE PACKET NOT SHOWN ON ILLUSTRATIONS IN MANUAL CAN STOP ASSEMBLY VALIDATOR PLATE XXX A/R PRICE LABELS (Specify Price Value) INSTALLATION INSTRUCTIONS - CAN STOP SERVICE MANUAL ANTI-CHEAT BRACKET INSTALLATION INSTRUCTIONS - ANTI CHEAT BRACKET OPTIONAL KITS & ACCESSORIES - NOT SHOWN COIN BOX LOCK ASSEMBLY LOCK - COIN BOX LOCK CAM - COIN BOX HEATER KIT DRAIN PAN HEATER KIT (110 V) DRAIN PAN HEATER KIT (220 V) OUTER DOOR HASP KIT ANTI CHEAT BRACKET RAIN GUARD CUSTOM LOCK CYLINDERS (CODED TO CUSTOMER SPECS.) 3

5 CABINET ASSEMBLY 4

6 CABINET ASSEMBLY ITEM PART NUMBER QTY DESCRIPTION XXX 1 CABINET WELD (Specify Color) /4-20 X 3/4 CARRIAGE BOLT /8 FLAT WASHER - NYLON XXX 1 TOP HINGE (Specify Color) /4 SPLIT LOCKWASHER /4-20 TWIN WHIZ NUT SNAP IN PLASTIC SPRING /16-18 X 3/4 HWH TYPE D XXX 1 BOTTOM HINGE (Specify Color) ft FOAM TAPE LEG LEVELER /2 FLAT WASHER DIA PUSH NUT ft TUBING - MAYON TUBE CLIP STUD DIA PUSH NUT ROLLER PIN DRAIN PAN LATCH NUT MOUNT /2-13 SQUARE NUT W/RETAINER NUT RETAINER EVAPORATOR SUPPORT - RIGHT LINER SUPPORT INSULATION - CABINET BOTTOM DRAIN PAN SPONGE EXTENSION BRACKET A/R #8-18 X 1/2 PHIL HWH TEK EVAPORATOR SUPPORT - LEFT CAN RACK RISER LINER WELD DRAIN TUBE #10-12 X 1 PHIL TH TYPE A INSULATION - CABINET SIDE INSULATION - CABINET TOP INSULATION - CABINET BACK WARNING LABEL - REFER (Not Shown) 5

7 DOUBLE DEPTH CAN RACK 6

8 DOUBLE DEPTH CAN RACK PARTITION PANEL - RIGHT CAN DEFLECTOR - SHORT CAN DEFLECTOR - LONG DIA TIE ROD PARTITION PANEL - LEFT DIA TIE ROD SINGLE COLUMN FRONT TIE #8-18 X 3/8 PHIL PH TYPE B MOTOR COVER - TOP CABINET HARNESS MOTOR COVER WIRE SHELF - BOTTOM BOTTOM SHELF INSERT BOTTOM SHELF BOTTOM LOOP TOP LOOP DEFLECTOR PLATE SUPPORT #8-32 X 38 PHIL PH MS #8-32 NUT - TWO WAY LOCK HANGER STRAP CENTER LOOP CENTER LOOP RETAINER STRAP UPPER SHELF DIA STUD PUSH NUT DIA STUD PUSH NUT 7

9 CAN RACK ASSEMBLY 8

10 CAN RACK ASSEMBLY END PANEL - RIGHT BACK CAN RACK TOP TIE STRIP - CAN GUIDE DIA TIE ROD END PANEL - LEFT FRONT TIE STRAP POP RIVET - 1/8 X 1/ EXTRUDED GROMMET MOTOR COVER #8-18 X 1/2 PHIL HWH TEK CABINET HARNESS TUBE RACK SUPPORT BOTTOM SHELF BOTTOM LOOP CENTER LOOP RETAINER STRIP TOP LOOP UPPER SHELF DIA TIE ROD DIA PUSH NUT DIA PUSH NUT 9

11 INNER DOOR ASSEMBLY 10

12 INNER DOOR ASSEMBLY ITEM PART NUMBER QTY DESCRIPTION INNER DOOR ASSEMBLY DOOR GASKET STORAGE SHELF A/R #8-18 X 1/2 PHIL HWH TEK SCREW INNER DOOR LINER DOOR INSULATION INNER DOOR WELD DOOR HINGE #10-32 X 1/2 PHIL TH W/ETW #10-32 HEX NUT FT. GASKET - 3/4" W/ADHSV DELIVERY CHUTE HINGE PIN TUBULAR SPEED NUT VEND PORT DOOR LOCK FUNNEL /8 X 1/4 POP RIVET INNER DOOR LOCK BRACKET INNER DOOR LATCH BUSHING SPACER #8-18 X 1/2 PHIL PH TEK LINE CHANNEL #8-32 NUT - TWO WAY LOCK CAN SLIDE ASSY DELIVERY CHUTE CAN SLIDE - SHORT CAN SLIDE - LONG /8 X 1/4 POP RIVET DELIVERY SUPPORT #8-32 X 3/8 PHIL PH MS DOOR HANDLE #10-24 X 3/8 PHIL TH W/ETW OPERATING INSTRUCTION LABEL A/R = As Required 11

13 COMPLETE DOOR ASSEMBLY 12

14 COMPLETE DOOR ASSEMBLY ITEM PART NUMBER QTY DESCRIPTION VALIDATOR PLATE WELD COIN INSERT CASTING ASSEMBLY - See Page # COIN INSERT RETAINER BRACKET #8-32 X 1/4 PHIL PH TYPE "T" Ft GASKET - 1/4 X 3/4 W/ADHV DELIVERY TRIM XXX 1 "T" HANDLE LATCH (Specify Color when ordering) #10-32 X 3/8 CARRIAGE BOLT #10-32 TWIN WHIZ NUT XXX 1 CHANGE BEZEL (Specify Color when ordering) STUD SELF THREAD NUT DOOR WELD "T" HANDLE BRACKET COIN CUP DOOR COIN CUP INNER DOOR LIFT A/R #8-18 X 1/2 PHIL HWH TEK BALLAST MECH DOOR ASSEMBLY - See Page # COIN BOX BRACKET - TOP COIN BOX WELD COIN BOX BRACKET - BOTTOM SELECT DOOR HARNESS INNER DISPLAY WELD LIGHT COVER - BOTTOM TRANSFORMER PLATE ASSEMBLY - See page # CAN CHUTE WELD TIE BRACKET DELIVERY BACK REFLECTOR PLASTIC HOLDER LAMP HARNESS PRESS CLIP - 1/4" LAMP HOLDER - TOP LAMP - F64 T12/CW LAMP HOLDER - BOTTOM #8-18 X 1/2 PHIL PH TYPE B #10-24 X 3/8 PHIL TH W/ETW MECH DOOR BRACKET - BOTTOM MECH DOOR BRACKET - TOP 41 1 SELECTION SWITCH ASSEMBLY - See Page # COIN MECH HARNESS PLUG BRACKET PLUG BRACKET W/NOTCH 45 1 VALIDATOR - CONTROLLER COMPONENTS - See Page # DOOR HINGE INNER #10-32 X 1/2 PHIL TH W/ETW #10-32 HEX NUT XXX 1 GRAPHICS SIGN FACE - Specify Design when ordering #8-18 X 1/4 PHIL HWH BUMPER LOCKING CLAMP - 3/4" CHANGE LABEL 13

15 VALIDATOR - CONTROLLER COMPONENTS ITEM PART NUMBER QTY DESCRIPTION READOUT WINDOW CONTROL BOARD MOUNT CD-16 CONTROLLER #6-20 X 1/2 PHIL PH TYPE B STANDOFF CONTROL BOARD COVER #6-32 X 1 1/4 PHIL HD SCREW COLD CONTROL LABEL SERVICE MODE LABEL CONTROLLER SHIELD VALIDATOR LABEL - BOTTOM VALIDATOR LABEL - TOP VALIDATOR - MAKA VOLT VALIDATOR - MAKA - 24 VOLT VALIDATOR - COINCO #8-32 HEX NUT W/ETW VALIDATOR HARNESS - MAKA VOLT HARNESS - MAKA - 24 VOLT VALIDATOR HARNESS - COINCO VALIDATOR PLATE (Used When Validator is Removed) 14

16 COIN INSERT CASTING ASSEMBLY ITEM PART NUMBER QTY DESCRIPTION COIN INSERT CASTING ASSEMBLY COIN RELEASE DECAL XXX 1 COIN RELEASE HANDLE (Specify Color when ordering) FILLER PLUG COIN & DOLLAR INSERT LABEL /8 FLAT NYLON WASHER XXX 1 COIN INSERT CASTING (Specify Color when ordering) TORSION SPRING - 11/ COIN RELEASE LEVER #12 INT/EXT LOCK WASHER #1/4-28 X 1/2 PHIL TH MS COIN CHUTE RETAINER #6-18 X 1/4 PHIL TRUSS HD TYPE A COIN CHUTE RETURN COIN CHUTE WELD 15

17 PUSH BUTTON & SELECTION ASSEMBLY ITEM PART NUMBER QTY DESCRIPTION PUSH BUTTON ASSEMBLY SWITCH BRACKET #8-18 X 1/4 PHIL HWH TEK SWITCH SWITCH SPRING #6-32 X 1 PHIL PH TAPTITE SELECTION HARNESS XXX - FLAVOR TAB (See note below) NOTE: Contact Selectivend for Flavor Tabs available. 16

18 MECH DOOR ASSEMBLY ITEM PART NUMBER QTY DESCRIPTION MECH DOOR ASSEMBLY COIN CHANGER - COINCO 9302-L COIN CHANGER - MARS TRC COIN RETURN CHUTE WELD #8-18 X 1/4 PHIL HWH SCREW COIN BOX TUBE COIN KICKER XXX 1 MECH DOOR (Specify Color) BUMPER MECH DOOR LATCH #8-18 X 1/2 PHIL PH TYPE B PIN COVER #8-18 X 3/8 PHIL PH TYPE B POWER SWITCH WARNING LABEL 17

19 TRANSFORMER/PLATE ASSEMBLY ITEM PART NUMBER QTY DESCRIPTION TRANSFORMER PLATE ASSY TRANSFORMER PLATE #8-32 X 3/8 PHIL PH MS TRANSFORMER CLOSED END SPLICE CAP #8-32 HEX NUT W/ETW POWER DISTRIBUTION HARNESS TRANSFORMER HARNESS - 24 V AMP CB LINE (ORANGE) AMP CB LINE (BLUE) CIRCUIT BREAKER - 3 AMP TOGGLE SWITCH DECAL - TOGGLE SWITCH PUSH TO RESET 115V LABEL 18

20 COMPLETE EJECTOR MECH ASSEMBLY UPPER & LOWER ITEM PART NUMBER QTY DESCRIPTION UPPER EJECTOR MECH ASSY LOWER EJECTOR MECH ASSY MOTOR - EJECTOR MECH MOTOR MOUNT PLATE #8-18 X 1/2 PHIL HWH TEK RETAINING BRACKET #8-18 X 1/2 PHIL PH TYPE B CAM - LARGE AUXILIARY EJECTOR (LOWER EJECTOR MECH ONLY) CAM SHAFT RETAINER (LOWER EJECTOR MECH ONLY) SPACER CAM - SMALL BUSHING - SNAP-IN EJECTOR MECH HARNESS MECH PLATE SOLD OUT SWITCH #4-40 X 3/4 PHIL PH TAPTITE SWITCH COVER SWITCH INSULATOR MOTOR COVER - BOTTOM - LOWER MECH ONLY(NOT SHOWN) 19

21 REFRIGERATION CHASSIS ASSEMBLY 20

22 REFRIGERATION CHASSIS ASSEMBLY ITEM PART N0. QTY DESCRIPTION REFRIGERATION ASSEMBLY REFER SYSTEM - 1/3 HP - R-134a BASE PLATE CONDENSER COIL -1/3 HP #1/4-20 X 3/8 SLTD HH MS /4-20 TWIN SPRING NUT SHROUD - CONDENSER FAN CHRISTMAS TREE CLIP RETAINING CLIP HARNESS MOUNTING BRACKET #8 EXT SHAKEPROOF LW #8 X 1/2 PHIL. TH TYPE "A" SMS SERVICE HARNESS #8 EXT SHAKEPROOF LW #8 x 1 1/2 PHIL PAN HD SMS COMPRESSOR - 1/3 HP - R COMPRESSOR GROMMET CLIP - COMPRESSOR MOUNTING WARNING DECAL OVERLOAD SPRING - OVERLOAD STARTING RELAY COVER BALE STRAP SUCTION LINE TUBE CAPILLARY DRIER DISCHARGE LINE ACCUMULATOR TUBE- ACCUM. CONNECTING TUBE - CAP. CONNECTING COIL - EVAPORATOR BRKET - ACCUM. TUBE SUPT #8-32 X 3/8 PHIL TH MS GROMMET DECAL - THERMOSTAT DIAL EVAPORATOR BAFFLE ITEM PART N0. QTY DESCRIPTION TAG - INSTRUCTION TOP BAFFLE EVAPORATOR BUSHING - STRAIN RELIEF #6 X 3/8 PHIL ROUND HD SMS CLAMP, CABLE EVAPORATOR FAN SHROUD POP RIVET BRACKET - CONDENSER FAN MTG /4-20 X 1/2 HH-LW TYPE D /4 EXT SHAKEPROOF LW CONDENSER FAN MOTOR 5 WATT #8-36 X 3/8 PHIL PAN HD MS FAN BLADE EXTENSION CORD CONDENSER FAN SILENCER /4-20 SPRING NUT NOTE: FOR ITEMS 58, 59 & 60 CHECK MANUFACTURER OF MOTOR BEFORE ORDERING HOWARD MOTOR FAN MOTOR 4 1/2 WATT FAN BLADE #3-48 X 3/16 RD HD MS FASCO MOTOR FAN MOTOR 4 1/2 WATT FAN BLADE #10-32 x 5/16 PHIL PH W/ETW MOTOR MOUNT #8-18 X 3/8 PHIL PH TYPE AB #10-32 X 5/16 PHIL PH W/ETW TY D THERMOSTAT TEMP CONTROL KNOB TEMP CONTROL COVER BRACKET - THERMOSTAT #8-32 X 3/8 PHIL THRSS HD MS #8-18 X 1/2 PHIL HWH TEK CLAMP - SUCTION LINE SUCTION LINE ASSY 21