UCS 500N7 MULTIFUNCTIONAL TESTGENERATOR FOR TRANSIENTS (EFT/BURST, SURGE & POWER FAIL) UP TO 7KV

Transcription

1 UCS 500N7 MULTIFUNCTIONAL TESTGENERATOR FOR TRANSIENTS (EFT/BURST, SURGE & POWER FAIL) UP TO 7KV FOR TESTS ACCORDING TO... > ANSI/IEEE C62.41 > ECE-R10 > EN > EN > EN > EN > EN > EN > EN > EN > EN > EN > IEC > IEC > IEC > IEC > IEC > IEC > IEC > IEC > IEC >... UCS 500N7 - MOST ENHANCED ULTRA COMPACT TESTER AS PER IEC X AND ANSI/IEEE C62.41 The UCS 500N7 ultra-compact simulator is the most versatile tester to cover transient and power fail requirements according to international standards (basic and generic standards) and product/ product family standards with voltage capability of up to 7.0 kv. Apart from the IEC/EN standard for surge testing it also complies to ANSI/IEEE C62.41 for surge and ringwave testing. The UCS 500N7 not only represents the most economic solution for full-compliant immunity tests and CE Marking but goes far beyond. Having a built-in CDN for single phase DUTs it can be extended for testing three-phase DUTs by means of an automatically controlled external coupling network up to 100A. EM TEST supplies a large range of accessories for the various applications. HIGHLIGHTS > Ultra-Compact Simulator up to 7.0kV APPLICATION AREAS INDUSTRY BROADCAST COMPONENTS TELECOM MEDICAL RESIDENTIAL > Burst module (IEC/EN ) > Surge module (IEC/EN Ed 3.0/-9) > PowerFail module (IEC/EN ) > Ringwave module (IEC/EN ) optional EM TEST > PAGE 1/10

2 BENEFITS SOFTWARE ALL IN ONE AND MORE - ALL WHAT YOU NEED FOR TESTS UP TO 7KV IEC.CONTROL SOFTWARE FOR CONTROL AND DOCUMENTATION The UCS 500N7 includes everything necessary to conduct fully compliant tests at levels that go far beyond common test requirements. Surge can be test up to 7.0kV either according to IEC/EN or ANSI/IEEE C The UCS 500N7 offers an integrated Ringwave module (optional) as per ANSI/IEEE C62.41 and IEC/EN for ringwave tests on mains supply lines. The UCS 500N7 can be operated manually from the front panel or by remote via the built-in USB or GPIB interface. Fail inputs allow to control an ongoing test sequence based on the status of the DUT. Monitoring outputs (BNC) are offered for easy signal measurement and verification. Safety features such as interlock and warning lamp control are available. Pre-programmed Standard Test routines allow highest user convenience. Still the UCS 500N7 offers the Quick Start test routine where parameters can be changed on-line during the test to evaluate the susceptibility level of an individual DUT, a most appreciated benefit for tests at development stage. Outstanding user convenience, clearly structured windows and operation features and the EM TEST standards library along with the flexibility to generate user specific test sequences very easily are the main features of iec.control software. The software is automatically configured according to the connected EM TEST generators. Extensive reporting capabilities help the user to create test reports that meet international requirements. iec.control is supported by Windows XP, Windows Vista, Windows 7 and Windows 8. Remote control is achieved either via USB or GPIB. iec.control supports a wide range of GPIB cards of National Instruments. OTHER MODELS UCS 500N SERIES - COMPACT TESTERS UP TO 7.0 KV The UCS 500N ultra-compact testers for EFT/Burst, Surge and Power Fail are available in two different models; with voltage capability up to 5.5kV or up to 7.0kV. OPERATION EASY TO OPERATE Front panel menu and function keys enable the user to program his test routines quickly and accurately. The cursor allows fast control of all test parameters of the programmed routine, thus test procedures are simplified and confidence is generated that every step is carried out correctly. EM TEST > PAGE 2/10

3 AUXILIARY DEVICES ACCESSORIES CNI 503-3PHASE COUPLING/DECOUPLING NETWORKS FOR BURST AND SURGE MS 100N - MAGNETIC FIELD COIL FOR POWER-FREQUENCY AND PULSED MAGNETIC FIELDS EM TEST offers a range of fully automatic 3-phase coupling/decoupling networks for burst and surge to extend the test capability for three-phase DUTs. The networks have a rated current of up to 100A. The MS 100N is a 1sqm magnetic field coil as specified in IEC/EN and IEC/EN Its design allows easy moving of the coil. The field coil is adjustable in height and allows for 360degr rotation. To generate power-frequency magnetic fields in the lower range the current transformer MC 2630 is used while high-field strength above 100A/m requires the MC current transformer. MV MOTORISED VARIAC FOR VOLTAGE VARIATION A motorised variac is offered as an alternative to the tapped autotransformers for voltage dips/interruptions and voltage variation tests as per IEC The motorised variac can also be used for automated magnetic field tests. V TAPPED VOLTAGE TRANSFORMER FOR VOLTAGE DIPS AND INTERRUPTIONS The V 4780 tapped autotransformer is designed to supply the required voltages as per IEC/EN Ed.2:2004 to perform voltage dips and interruptions. V 4780S2 - TAPPED VOLTAGE TRANSFORMER FOR VOLTAGE DIPS AND INTERRUPTIONS The V 4780S2 tapped autotransformer is designed to supply the required voltages as per IEC/EN Ed.2:2004 to perform voltage dips and interruptions. Compared to the manually operated V 4780 the V 4780S2 model offers automatic change of taps according to the selected voltage level. CNV 504/508 N- AND T-SERIES - SURGE COUPLING/DECOUPLING NETWORKS FOR SIGNAL/DATA LINES CNV 504/508 N- and T-series coupling/decoupling networks are available to perform surge tests on I/O lines, signal/data lines and telecom lines as per IEC/EN Ed 3.0. HFK - CAPACITIVE COUPLING CLAMP The HFK is a fully compliant capacitive coupling clamp as per specification of IEC/EN ITP - IMMUNITY TEST PROBES ITP is a tool being used for development test. It consists of a variety of electrical field probes. The probes allow to locate weak points within a system or on a PCB. The burst pulse is used to generate the disturbance signal. CA EFT KIT - VERIFICATION KIT FOR EFT/BURST PULSES As per IEC/EN Ed.2 the characteristic of the burst generator needs to be verified with two different loads, 50ohm and 1,000ohm. EM TEST offers a calibration kit consisting of the two loads and an adapter to verify the pulses at the DUT output. CA HFK KIT - VERIFICATION KIT FOR CAPACITIVE COUPLING CLAMP The IEC/EN Ed 3.0 published 2012 recomends the calibration of the capacitive coupling clamp into a 50ohm coaxial load. The capacitive coupling clamp (HFK) is connected to the 50 ohm output of the EFT generator. A flexible insulated plate inside the HFK is connected to a coaxial 50 ohm load resistor for verificate the EFT / Burst wave of the capacitive coupling clamp. EM TEST > PAGE 3/10

4 ELECTRICAL FAST TRANSIENTS ELECTRICAL FAST TRANSIENTS BURST MODULE, EFT/N7 TEST ROUTINES As per EN/IEC and EN , -6-2 Quick Start On-line adjustable parameters, easy-to-use Test voltage 200V - 5,500 V ± 10%; 100V - 2,750 V ± 10% into 50 ohm Standard Test routines Pulse shape 5/50 ns into 50 ohm and 1,000 ohm As per IEC , Levels 1-4 As per EN , -6-2 Manual Standard Test routine tr 5 ns ± 30% into 50 ohm; 5 ns ± 30% into 1,000 ohm User Test routines Pulse width td 50 ns ± 30% into 50 ohm; 50 ns -15/+100 ns into 1,000 ohm Source impedance 50 ohm Polarity Positive, negative Synchronous burst release Random burst release Change voltage after T Frequency sweep within one burst Frequency sweep with constant number of pulses Frequency sweep with constant burst duration Change polarity after T TRIGGER CIRCUIT Trigger of bursts Automatic, manual, external Synchronization 0-360, resolution 1 ( Hz) Burst duration td = 0.10 ms ms Repetition rate tr = 10 ms - 9,999 ms Spike frequency f = 0.1 khz - 1,000 khz Test duration T = 0:01 min - 99:59 min T > 99:59 min --> endless OUTPUTS Direct Via 50 ohm coaxial connector Coupling mode L, N, PE; all combinations DUT supply AC: 300 V/16 A; 50/60 Hz DC: 300 V/16 A CRO trigger 5 V trigger signal for oscilloscope HFK Capacitive coupling clamp as per IEC KW50 100:1 divider, 50 ohm KW :1 divider, 1,000 ohm CA EFT kit Kit for burst pulse verification consisting of KW50, KW1000 and adapter for DUT port in a plastic case for storage CA HFK kit Adapter set for capacitive coupling clamp calibration included: - Transducer plate as per IEC/EN Ed Support for positioning the KW 50 adapter on 100mm height as the capacitive coupling clamp CA MC F Adapter to match KW 50 load resistor to the EUT supply of 3-phase N-series coupling network A6dB 6dB attenuator, 50 ohm ITP Immunity test probes (electrical field generation) ITP/H Immunity test probes (magnetic field generation) EM TEST > PAGE 4/10

5 COMBINATION WAVE / SURGE COMBINATION WAVE / SURGE SURGE MODULE, VCS/N7 TEST ROUTINES As per EN/IEC Ed 3.0 and EN , -6-2 Quick Start One-line adjustable parameters, easy-to-use Voltage (o.c.) 250 V - 7,000 V ± 10% Pulse front time 1.2 us ± 30% Standard Test routines As per IEC , Levels 1-4 As per EN , -6-2 Manual Standard Test routine Pulse time to half value 50 us ± 20% User Test routines Current (s.c.) Max. 3,500 A ± 10% Pulse front time 8 us ± 20% Change polarity after n pulses Change coupling after n pulses Change voltage after n pulses Change phase angle after n pulses Pulse time to half value 20 us ± 20% Pulsed Magnetic Field Polarity Positive, negative, alternating As per IEC Test levels 100, 300 and 1,000 A/m Test level steplessly adjustable under Quick Start Counter 1-30,000 or endless, selectable TRIGGER CIRCUIT Release of pulses Automatic, manual, external Synchronization 0-360, resolution 1 Repetition rate Max. 0.5 Hz (2 s s) CNV 504Nx Coupling network for 4 signal/data lines as per IEC Ed 3.0 CNV 508Nx Coupling network for 8 signal/data lines as per IEC Ed 3.0 CNI 508N2 Assembly Set of coupling/decoupling and protection networks for testing unshielded and shielded high-speed communication lines (Ethernet lines) IMN 2 Impedance matching adapter to match direct output to 2ohm source impedance OUTPUTS Direct Via HV connectors for external coupling networks (Zi = 2 ohm with optional adapter IMN 2) Coupling modes As per IEC : Line to line with 2 ohm Line(s) to ground with 12 ohm As per ANSI/IEEE C62.41 Line to line with 2ohm Line(s) to ground with 2ohm DUT supply AC: 300 V/16 A; 50/60 Hz DC: 300 V/16 A CRO trigger 5 V trigger signal for oscilloscope MEASUREMENTS CRO Û-monitor 10 Vp at 7,000 V CRO Î-monitor 10 Vp at 3,500 A Peak voltage 7,000 V in the LCD display Peak current 3,500 A in the LCD display Overcurrent protection Breaks the Sureg test when the surge current is over the limit, Limitter for differential mode, Limitter for common mode EM TEST > PAGE 5/10

6 POWER FAIL, DIPS & INTERRUPTIONS, VOLTAGE VARIATIONS POWER FAIL, DIPS & INTERRUPTIONS, VOLTAGE VARIATIONS POWER FAIL MODULE, PFS/N7 TEST ROUTINES As per EN/IEC and EN , -6-2 Quick Start On-line adjustable parameters, easy-to-use Channel PF1/PF2 AC voltage: max. 300 V AC current: max. 16 A Standard Test routines Frequency 16 Hz Hz Switching time < 5us into a 100ohm resistive load Inrush current > 500 A As per IEC for AC supplies As per IEC for DC supplies As per EN , -6-2 Manual Standard Test routine Protection Both channels are protected against short-circuit conditions. User Test routines Voltage variation, external variac control Change phase angle after n events Change event duration after n events Inverse mode 50/60Hz magnetic field As per EN/IEC Test levels 1, 3, 10 and 30A/m with external current transformer MC2630 Test levels 100, 300 and 1,000A/m with external current transformer MC26100 TRIGGER CIRCUIT Trigger of events Automatic, manual, external Synchronization 0-360, resolution 1 ( Hz) Repetition rate 10 ms - 9,999 s Event duration 20 us - 9,999 s OUTPUTS DUT terminals L, N and PE CRO trigger 5V trigger signal for oscilloscope MEASUREMENTS DUT voltage In the LCD display DUT current In the LCD display MON V Measurement of the DUT voltage; built-in 100:1 divider MON I Measurement of the DUT current; 10 mv/a; max. 1,000 A V 4780 Tapped autotransformer as per IEC Ed.2 V 4780 S2 Tapped autotransformer as per IEC Ed.2 with automatic change of tap MV 2616 Motorised variac (0-260 V, 16 A) MS 100N Magnetic field coil, 1m x 1m MC 2630 Current transformer for magnetic fields up to 30 A/m MC Current transformer for magnetic fields up to 1,000 A/m CA PFS Calibration box for inrush current verification as per IEC EM TEST > PAGE 6/10

7 RINGWAVE RINGWAVE RINGWAVE MODULE, RWG/N7 (OPTIONAL) TRIGGER CIRCUIT As per ANSI/IEEE C62.41 and EN/IEC Release of pulses Automatic, manual, external Synchronization 0-360, resolution 1 Repetition rate max. 1 Hz (1 s s) Test voltage 250 V - 6,000 V ± 10% Voltage Wave shape (open circuit) 0.5 us ± 30% (first peak) MEASUREMENTS Oscillation frequency 100 khz ± 10% CRO Û-monitor 10 Vp at 7,000 V Decaying Peak 2 to peak 1 = % Peak 3 to peak 2 = 40-80% Peak 4 to peak 3 = 40-80% CRO Î-monitor 10 Vp at 3,500 A OUTPUTS Current Wave shape (short circuit) Direct Via HV-safety lab connectors <= 1.0 us Coupling mode Oscillation frequency 100 khz ± 10% L, N, PE; line to line and line(s) to ground DUT supply Source impedance 12 ohm, 30 ohm AC: 300 V/16 A; 50/60 Hz DC: 300 V/16 A CRO trigger 5 V trigger signal for oscilloscope Peak current As per selected source impedance Polarity Positive, negative TEST ROUTINES Quick Start RINGWAVE MODULE, RWG/N7.1 (OPTIONAL) On-line adjustable parameters, easy-to-use As per UL 1741, ANSI/IEEE C62.41 and EN/IEC Test voltage 250 V - 6,000 V ± 10% Voltage Wave shape (open circuit) 0.5 us ± 30% (first peak) Oscillation frequency 100 khz ± 10% Decaying Peak 2 to peak 1 = % Peak 3 to peak 2 = 40-80% Peak 4 to peak 3 = 40-80% Current Wave shape (short circuit) <= 1.0 us Oscillation frequency 100 khz ± 10% Source impedance 12 ohm, 30 ohm, 50 ohm Peak current As per selected source impedance, Polarity Positive, negative EM TEST > PAGE 7/10

8 TELECOM SURGE TELECOM SURGE TSURGE MODULE, TSURGE7 (OPTIONAL) TRIGGER CIRCUIT Test voltage (o.c.) 250 V - 7,000 V ± 10% Trigger of events Automatic, manual, external Energy storage capacitor 20 uf Repetition rate max Hz (3 s s) Polarity Positive, negative, alternating OUTPUTS Counter 1-30,000 or endless, selectable As per ITU For 2-wire T1/T2 with 25 ohm each As per ITU and ETSI recommendations As per FCC part 68 For 2-wire T1/T2 with 25 ohm each As per IEC Ed 3.0 For 4-wire T1/T2/T3/T4 with 25 ohm each Front time 10 us ± 30% Pulse duration 700 us ± 20% For other requirements special output configurations are available As per FCC part 68, Pulse B Front time 9 us ± 30% Pulse duration 720 us ± 20% Output ohm output 6 A A (short circuit) 5 us ± 30% Pulse duration 320 us ± 20% As per IEC us ± 30% Pulse duration 700 us ± 20% Output ohm output 6 A A (short circuit) 5 us ± 20% Pulse duration 320 us ± 20% CNV 504T5 Coupling/decoupling network for unshielded symmetrical lines (communication lines) as per IEC/EN Ed.3 (fig. 10) for 4 lines. CNV 508T5 Coupling/decoupling network for unshielded symmetrical lines (communication lines) as per IEC/EN Ed.3 (fig. 10) for 8 lines. EM TEST > PAGE 8/10

9 GENERAL DATA GENERAL DATA INTERFACES SAFETY Serial interface USB Safety standard EN/IEC Parallel interface IEEE 488, addresses 1-30 Security circuit Control input (24 VDC) Analog output 0-10 VDC to control an external transformer Warning lamp Floating contact (max. 230 V/6 A) CN interface 15pin SubD connector to control an external coupling network ACCESSORIES INCLUDED Fail inputs DUT monitoring via Fail1 and Fail2 input (one each) DIMENSIONS Housing 19", 6 HU Weight Approx. 29 kg Mains supply cable Plug depends on the country of use DUT supply cable Plug depends on the country of use DUT adapter Socket depends on the country of use Operation manual, Calibration certificate, iec.control remote control software MAINS Supply voltage 115 / 230 VAC +10%/-15% Power consumption Approx. 75 W Frequency 50/60 Hz Fuses 2x 2 AT (230 V) or 2x 4 AT (115 V) CNI 503Bx 3-phase coupling/decoupling networks as per IEC and -4-5 up to 100A per phase iec.control 1 Remote control and documentation software, including standard test routines and reporting capabilities. OptoLink Optical interface Opto link, 3 m cable USB A connector, replaces the USB interface EM TEST > PAGE 9/10

10 COMPETENCE WHEREVER YOU ARE CONTACT EM TEST DIRECTLY Switzerland USA / Canada EM TEST (Switzerland) GmbH > Sternenhofstraße 15 > 4153 Reinach > Switzerland Phone +41 (0)61/ > Fax +41 (0)61/ Internet: > sales.emtest@ametek.com AMETEK Compliance Test Solutions > 52 Mayfield Ave. > Edison > NJ Phone +1 (732) Internet: > sales.emtest@ametek.com Germany AMETEK CTS Germany GmbH > Lünener Straße 211 > Kamen > Deutschland Phone +49 (0)2307/ > Fax +49 (0)2307/17050 Internet: > info.cts@ametek.de France EM TEST FRANCE > Le Trident - Parc des Collines > Immeuble B1 - Etage 3 > 36, rue Paul Cézanne > Mulhouse > France Phone +33 (0) > Fax +33 (0) Internet: > info@emtest.fr P.R. China E & S Test Technology Limited > Rm 913, Leftbank > No. 68 Bei Si Huan Xi Lu > Haidian District > Beijing > P.R. China Phone +86 (0) > Fax +86 (0) Internet: > info@emtest.com.cn Republic of Korea EM TEST Korea Limited > #405 > WooYeon Plaza > #986-8 > YoungDeok-dong > Giheung-gu > Yongin-si > Gyeonggi-do > Korea Phone +82 (31) > Fax +82 (31) Internet: > sales@emtest.co.kr Poland EM TEST Polska > ul. Ogrodowa 31/35, Warszawa > Polska Phone +48 (0) Internet: /pl > infopolska.emtest@ametek.com Information about scope of delivery, visual design and technical data correspond with the state of development at time of release. Subject to change without further notice. EM TEST > PAGE 10/10