Alternator Identification
|
|
|
- Winfred Banks
- 9 years ago
- Views:
Transcription
1 Alternator Identification Briggs & Stratton engines are equipped with a number of different alternator systems to meet the requirements of equipment manufacturers. For example, a large lawn tractor with accessories may require a 6 amp regulated system, whereas a snow thrower with a single headlight requires an AC Only system. Knowing the type of alternator system an engine is equipped with is important, particularly when an engine is being replaced. Briggs & Stratton alternator systems are easily identified by the color of the stator output wire(s) and the connector. Stator Output Wire(s) And Connector (typical) AC Only DC Only ONE BLACK LEAD FROM ENGINE (STATOR) RED ONE RED LEAD FROM ENGINE (STATOR ) TO EQUIPMENT WHITE OUTPUT LEAD TO EQUIPMENT DIODE Volts AC for lighting circuit. One black lead from stator. White connector output lead. ampdcunregulatedforchargingbattery. One red lead from stator. Diode encased at connector. Red connector output lead.
2 RED AND BLACK LEADS FROM ENGINE (STATOR) Dual Circuit RED LEAD DC OUTPUT BLACK LEAD TO EQUIPMENT 0 or 6 amp Regulated RED OUTPUT LEAD DC CHARGING CIRCUIT RED LEAD ONE RED LEAD TWO BLACK LEADS FROM ENGINE (STATOR) TO EQUIPMENT WHITE LEAD AC FOR LIGHTS WHITE amp DC unregulated for charging battery (ONE red lead from stator). Volts AC for lighting circuit (ONE black lead from stator). Diode encased at connector. White connector with two pin terminals. TO EQUIPMENT AMPS DC () TO LIGHTS WHITE LEAD TriCircuit TWO DIODES ENCASED IN ONE BLACK LEAD FROM ENGINE (STATOR) REGULATOR RECTIFIER TWO YELLOW LEADS YELLOW 0 or 6 amp DC regulated for charging battery. Alternatoroutputisdeterminedbytheflywheel alternator magnet size. 0 and 6 amp system use the same stator, color coding and regulatorrectifier. Two black leads from stator. Yellow connector with two pin terminals. Two yellow leads to regulatorrectifier. One red lead from regulatorrectifier to red connector output lead. RED LEAD AMPS DC () TO AND CLUTCH CIRCUIT 0 amp AC. One black lead from stator. Green connector. Two diodes encased in wire harness. Red and white output leads. GREEN TO EQUIPMENT 99 Regulator/Rectifier Used With Charge Indicator Circuit RED AND RAISED RIB INDICATES DC OUTPUT BLUE CHARGING INDICATOR ONE BLACK LEAD FROM ENGINE (STATOR) or 9 amp Regulated RED TO EQUIPMENT WHITE GREEN YELLOW 99 REGULATOR RECTIFIER TWO YELLOW LEADS YELLOW REGULATOR RECTIFIER or 9 amp DC regulated for charging battery. Alternator output ( or 9 amp) is determinedby flywheel alternator magnet size. Uses same stator as TriCircuit system. One black lead from stator. Green connector. Uses same stator as 0 and 6 amp system. DC output the same as 0 or 6 amp system. Charge indicator light andwiring suppliedby equipment manufacturer. Red DC output wire to white connector. Blue charge indicator wire to white connector.
3 Engine/Alternator Replacement Information With the exception of the AC Only alternator, all of the alternator systems referred to in this book have a battery as part of the electrical system. There are specialized applications that use an alternator without a battery. An example would be certain generators or welders that use alternator output to excite an electrical field. For theequipment tofunction, the alternator output must be very evenly matched to the equipment requirements. When replacing an engine in these applications, the alternator must be the same as the original. Replacing Briggs & Stratton Engines When replacing an older Briggs & Stratton engine on apiece ofequipment witha newerbriggs &Stratton engine, sometimes the newer engine has an alternator system different from the alternator system on the original engine. This means that the output connector on the replacement engine is not compatible with the original wiring harness on the piece of equipment. For example, the original engine may have been equipped with a Dual Circuit system and the replacement engine is equipped with a regulated system. We can integrate the two systems by making an adapter harness from readily available parts. Generally an unregulated DC system (DC Only, DualCircuit) shouldnot beused toreplace aregulated system because alternator output may not be sufficient for equipment requirements. However, because the equipment requirements are usually much less on an unregulated DC system, a regulated system may be used as a replacement. The regulator/rectifier prevents the battery from being over charged. NOTE: The AC Only, DC Only, Dual Circuit, TriCircuit as well as the and 0 amp regulated systems use flywheels with small alternator magnets. The 9 and 6 amp regulated systems use flywheels with the large alternator magnets. See figure below for magnet sizes. ALTERNATOR MAGNETS *Small Magnet 7/8 x /6 (mm x 8mm) *Large Magnet /6 x /6 (7mm x mm) * V Twin Alternator Magnet Size: Small 7/8 x / ( mm x 7 mm) Large 7/8 x 9/ ( mm x mm)
4 The following are alternator replacement combinations which require an adapter harness. All of the necessary components are shown.. Original engine equipped with AC Only alternator. Replacement engine equipped with Dual Circuit alternator. Modify 96 harness supplied with replacement engine by removing red DC wire. Then, splice 97 connector into white AC wire and connect to equipment harness. AC BLACK DUAL CIRCUIT (FROM ENGINE) 96 AC (WHITE) EQUIPMENT DC RED RIB RIB SPLICE 97 (GREEN). Original engine equipped with DC Only alternator. Replacement engine equipped with Dual Circuit alternator. Modify 96 harness supplied with replacement engine by removingwhite ACwire. Then,splice 97 connector into red DC wire and connect to equipment harness. DUAL CIRCUIT (FROM ENGINE) 96 DC (RED) EQUIPMENT AC BLACK DC RED RIB SPLICE 97 RIB (GREEN)
5 . Original engine equipped with Dual Circuit alternator. Replacement engine equipped with, 9, 0 or 6 amp regulated system. Modify 9 harness supplied with replacement engine by splicing in 9996 connector assembly. Connect to equipment harness. OUTPUT FROM REGULATOR SPLICE 9996 ASSEMBLY EQUIPMENT 9 RIB RIB. Original engine equipped with TriCircuit alternator. Replacement engine equipped with, 9, 0 or 6 amp regulated system. Modify 9 harness supplied with replacement engine by splicing into charging circuit wireand lighting circuit wire in equipment harness. NOTE:THE DIODES MUST BE REMOVED FROM THE EQUIPMENT. Diodes Must Be Removed From Equipment Harness OUTPUT FROM REGULATOR SPLICE LIGHTING CIRCUIT EQUIPMENT 9 CHARGING CIRCUIT
6 . Original engine equipped with Dual Circuit alternator. Replacement engine equipped TriCircuit alternator. Discard 9606 diode harness supplied with new engine. Install 96 regulator/rectifier. Add 9 harness and modify by splicing in 9996 connector assembly. Connect to equipment harness. OUTPUT FROM ALTERNATOR SPLICE 9996 ASSEMBLY 9 RIB RIB EQUIPMENT 96 REGULATOR/RECTIFIER 6. Original engine equipped with amp regulated system. Replacement engine equipped with TriCircuit alternator. Discard 9606 diode harness supplied with new engine. Transfer 96 regulator/rectifier from original engine. Connect to equipment harness. The following alternator replacement combinations require no modifications. 7. Original engine equipped with DC Only alternator. Replacement engine equipped with, 9, 0 or 6 amp regulated system. Direct Replacement. Connect to equipment harness. 8. Original engine equipped with amp regulated system. Replacement engine equipped with 9, 0 or 6 amp regulated system. Direct Replacement. Connect to equipment harness. 9. Original engine equipped with 9 amp regulated system. Replacement engine equipped with 0 or 6 amp regulated system. Direct Replacement. Connect to equipment harness. 0. Original engine equipped with 0 amp regulated system. Replacement engine equipped with 9 or 6 amp regulated system. Direct Replacement. Connect to equipment harness. 6
7 Briggs & Stratton Engine Replacing Engine Of Another Manufacturer When replacing the engine of another manufacturer with a Briggs & Stratton engine, the equipment requirements must be known so that the replacement alternator system has the same output as the original system provided. Often the equipment wiring harness is not compatible with the Briggs & Stratton alternator output harness. To create a compatible system it may be necessary to modify the the equipment wiring harness. To do this a wiring diagram for the equipment is essential. The original keyswitch may also create a problem. Even though the keyswitch harness connectors appear to be identical, there are internal differences to keyswitches. Therefore it is necessary to have a diagram of the keyswitch showing the terminal positions and their functions. For example, see the terminal switch diagrams in Figure and Figure. The keyswitch in Figure is compatible with all Briggs & Stratton alternators. Note in Figure, that when the brand X keyswitch is in the START position there is no battery voltage available to the # switch terminal. Consequently, if the replacement Briggs & Stratton engine was equipped with a carburetor solenoid, it would not function. This is why it is important to have a diagram of the keyswitch when replacing engines, or replace the keyswitch with one that is compatible with all Briggs & Stratton alternator systems. NOTE: The terminal Briggs & Stratton keyswitch, part no , shown in Fig. has been replaced by a 6 terminal keyswitch, part no. 96. The additional terminal provides a direct connection for the charging lead at the keyswitch. Terminal No. B & S Switch Terminal Positions Function Ground (Used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) Brand X Switch Terminal Positions Terminal No Function Accessory To Stop Switch Terminal On Engine (Ground) To Regulator (Charging) To Solenoid (tab terminal) To Battery (battery terminal on solenoid) L G M B S L G M B S M A R B M R S S A B OFF RUN OFF RUN L G M B S M A R B S START START Fig. It is not possible to show all of the wiring diagrams or keyswitch combinations that are used by equipment manufacturers. However, the following wiring diagrams for the most popular Briggs & Stratton engines may be used as a guide whenreplacing anengine. Thewiring diagramsshow thetype of keyswitch that is compatible with the alternator system shown. 7 Fig.
8 Typical Dual Circuit Alternator Wiring Diagram Pole Switch Briggs & Stratton Part No ALTERNATOR ANTIAFTERFIRE DIODE KEY DC OUTPUT S AMMETER TAB MOTOR VOLT Key Switch Test Switch Position Continuity. OFF *. RUN. START * Terminal Grounded Internally To Key Switch Case Terminal No. Function Ground (Used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) 8
9 Typical Dual Circuit Alternator Wiring Diagram 6 Pole Switch Briggs & Stratton Part No. 96 ALTERNATOR ANTIAFTERFIRE DIODE KEY S DC OUTPUT Ammeter 6 Ammeter (optional) TAB MOTOR VOLT Key Switch Test Switch Position Continuity Terminal No. Function. OFF * 6. RUN 6. START *Terminal Grounded Internally To Key Switch Case With ammeter shown in optional position, note that and symbols are reversed. The symbol must always be connected to the alternator side. To Ground (used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) 6 To Alternator (DC Output) 9
10 Typical 6 amp Regulated Alternator Wiring Diagram Pole Switch Briggs & Stratton Part No ANTIAFTERFIRE ALTERNATOR KEY DC OUTPUT REGULATOR RECTIFIER AMMETER TAB S MOTOR VOLT Key Switch Test Switch Position Continuity. OFF *. RUN. START * Terminal Grounded Internally To Key Switch Case Terminal No. Function Ground (Used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) 0
11 Typical 6 amp Regulated Alternator Wiring Diagram 6 Pole Switch Briggs & Stratton Part No. 96 ANTIAFTERFIRE ALTERNATOR KEY DC OUTPUT REGULATOR RECTIFIER AMMETER 6 Ammeter (optional) TAB S MOTOR VOLT Key Switch Test Switch Position Continuity Terminal No. Function. OFF * 6. RUN 6. START * Terminal Grounded Internally To Key Switch Case With ammeter shown in optional position, note that and symbols are reversed. The symbol must always be connected to the alternator side. To Ground (used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) 6 To Alternator (DC Output)
12 Typical 6 amp Regulated Alternator Wiring Diagram With Charge Indicator Light 6 Pole Switch Briggs & Stratton Part No. 96 ALTERNATOR ANTIAFTERFIRE CHARGE INDICATOR LIGHT BLUE 6 REGULATOR RECTIFIER AMMETER RED DC OUTPUT RAISED RIB Ammeter (optional) TAB S Starter Motor VOLT Key Switch Test Switch Position Continuity Terminal No. Function. OFF * 6. RUN 6. START * Terminal Grounded Internally To Key Switch Case With ammeter shown in optional position, note that and symbols are reversed. The symbol must always be connected to the alternator side. To Ground (used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) 6 To Alternator (DC Output)
13 Typical /9 amp Regulated Alternator Wiring Diagram 6 Pole Switch Briggs & Stratton Part No. 96 TRICIRCUIT STATOR ANTIAFTERFIRE Alternator KEY DC OUTPUT 6 REGULATOR RECTIFIER AMMETER Ammeter (optional) TAB S MOTOR VOLT Key Switch Test Switch Position Continuity Terminal No. Function. OFF * 6. RUN 6. START * Terminal Grounded Internally To Key Switch Case With ammeter shown in optional position, note that and symbols are reversed. The symbol must always be connected to the alternator side. To Ground (used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) 6 To Alternator (DC Output)
14 Typical /9 amp Regulated Alternator Wiring Diagram 6 Pole Switch Briggs & Stratton Part No. 96 TRICIRCUIT STATOR ANTIAFTERFIRE Alternator KEY DC OUTPUT 6 REGULATOR RECTIFIER AMMETER Ammeter (optional) TAB S MOTOR VOLT Key Switch Test Switch Position Continuity Terminal No. Function. OFF * 6. RUN 6. START * Terminal Grounded Internally To Key Switch Case With ammeter shown in optional position, note that and symbols are reversed. The symbol must always be connected to the alternator side. To Ground (used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) 6 To Alternator (DC Output)
15 Typical TriCircuit Alternator Wiring Diagram 6 Pole Switch Briggs & Stratton Part No. 96 TRICIRCUIT STATOR ALTERNATOR ANTIAFTERFIRE KEY DC OUTPUT DC OUTPUT AMMETER 6 S CLUTCH Ammeter (optional) TAB ELECTRIC CLUTCH MOTOR VOLT Key Switch Test Switch Position Continuity Terminal No. Function. OFF * 6. RUN 6. START * Terminal Grounded Internally To Key Switch Case With ammeter shown in optional position, note that and symbols are reversed. The symbol must always be connected to the alternator side. To Ground (used only with insulated panel) To Carburetor Solenoid. To Stop Switch Terminal On Engine To Solenoid (tab terminal) To Battery (battery terminal on solenoid) 6 To Alternator (DC Output)
16 TRI CIRCUIT STATOR Typical TriCircuit Alternator Wiring Diagram With Resistor Pole Switch Briggs & Stratton Part No ALTERNATOR ANTIAFTERFIRE See Note KEY DC OUTPUT DC OUTPUT S AMMETER RESISTOR A OFF B Note: If clutch switch is in ON position with keyswitch OFF, battery will discharge thru clutch. To prevent this, route wire B to # terminal on keyswitch. However, antiafterfire solenoid will not shut off. Remove antiafterfire solenoid or convert system to 6 pole switch. ON CLUTCH Switch Position Continuity. OFF *. RUN. START * Terminal Grounded Internally To Key Switch Case ELECTRIC CLUTCH VOLT TAB MOTOR
17 TRI CIRCUIT STATOR Typical TriCircuit Alternator Wiring Diagram With Resistor 6 Pole Switch Briggs & Stratton Part No. 96 ALTERNATOR ANTIAFTERFIRE KEY DC OUTPUT DC OUTPUT S AMMETER RESISTOR 6 TAB OFF ON MOTOR CLUTCH DPDT Key Switch Test Switch Position Continuity. OFF * 6. RUN 6. START * Terminal Grounded Internally To Key Switch Case ELECTRIC CLUTCH VOLT 6
18 MS0/98 Copyright 998 by Briggs & Stratton Corporation Printed in U.S.A. MS0/98 Copyright 998 by Briggs & Stratton Corporation Printed in U.S.A.
ENGINE ALTERNATOR REPOWER GUIDE
ENGINE ALTERNATOR REPOWER GUIDE ThePowerPortal.com Your One Your Stop One Information Stop Source Information Source Briggs & Stratton has developed a powerful and flexible private web-based portal for
KTM AC to DC Stator Conversion Instructions (Floating the ground)
KTM AC to DC Stator Conversion Instructions (Floating the ground) Overview: The following procedure is intended to convert AC (Alternating Current) electrical systems to DC (Direct Current). A qualified
8 coil stator 11 coil stator
Below is a schematic of a typical scooter electrical set up as far as the stator, CDI, rectifier/regulator go along with the other items running on the electrical system; This is the 6 coil stator common
STUDY OF CELLPHONE CHARGERS
STUDY OF CELLPHONE CHARGERS Author : Suraj Hebbar Systems Lab, CeNSE,IISc Banglore ABSTRACT This report shows charging nature of different cellphone chargers with different cellphones. Here we took into
The Charging System. Section 5. Charging System. Charging System. The charging system has two essential functions:
The Charging System Charging System The charging system has two essential functions: Generate electrical power to run the vehicle s electrical systems Generate current to recharge the vehicle s battery
Ohm's Law and Circuits
2. Conductance, Insulators and Resistance A. A conductor in electricity is a material that allows electrons to flow through it easily. Metals, in general, are good conductors. Why? The property of conductance
SYSTEM 4C. C R H Electronics Design
SYSTEM 4C C R H Electronics Design SYSTEM 4C All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, A outputs. Independent 25
Left Hand Limit Switch. Housing. Left Hand. Connections. Motor Connector BROWN PURPLE GRAY BLACK DARK BLUE BLACK BROWN BROWN LIGHT BLUE.
LIGHT BLUE GRAY PURPLE Circuit Breaker Intput Circuit Breaker Output #1 Relay Left Hand Limit Switch Housing Left Hand Motor Connector Right Hand Limit Switch on Radiator Support Right Hand Limit Switch
Wires & Connections Component Circuit Symbol Function of Component. Power Supplies Component Circuit Symbol Function of Component
Lista Dei Simboli Dei Circuiti Per i Componenti Elettronici Wires & Connections Wire Wires joined Wires not joined To pass current very easily from one part of a circuit to another. A 'blob' should be
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Electric Vacuum Pump Kit 28146 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully follow these instructions
Diagnosing and Understanding Starting Problems on the ZR-1 Marc Haibeck 28-Sep-13
Diagnosing and Understanding Starting Problems on the ZR-1 Marc Haibeck 28-Sep-13 There are three basic failure conditions: - A VATS security system lockout - A click from the starter solenoid but no engine
Wiring diagram layout
Wiring diagram layout 3 30 Relay panel Indicated by grey area. 500 0,0 WIRING COLOR CODE 00 D/50,5 / T0a/ ws = white = black = red br = bwn gn = green bl = blue gr = grey li = lilac ge = yellow bl T 4e/
Understanding the Alternator
http://www.autoshop101.com THIS AUTOMOTIVE SERIES ON ALTERNATORS HAS BEEN DEVELOPED BY KEVIN R. SULLIVAN PROFESSOR OF AUTOMOTIVE TECHNOLOGY AT SKYLINE COLLEGE SAN BRUNO, CALIFORNIA ALL RIGHTS RESERVED
Windshield Wiper Motors
Windshield Wiper Motors Originally posted by Dan Masters, [email protected] Also see http://www.advanceautowire.com/ WIPER OPERATION: There are three major components to a wiper motor: Motor Rotary to linear
POINTS POSITION INDICATOR PPI4
POINTS POSITION INDICATOR PPI4 Advanced PPI with Adjustable Brightness & Simplified Wiring Monitors the brief positive operating voltage across points motors when they are switched Lights a corresponding
73 Chevy C10 Ammeter to Volt Gauge Conversion Mark and Michael Olson 2013 Rev 1.0
73 Chevy C10 Ammeter to Volt Conversion Mark and Michael Olson 2013 Rev 1.0 The ammeter in my son s 73 Chevy C10 did not work, so we decided to convert it to a more modern volt gauge. We made a number
Replace That Bad Diode
Replace That Bad Diode A common problem in any restoration is fixing and replacing inoperative or missing electrical components. If the exact part cannot be located then the restorer is forced to improvise.
Points Position Indicator (PPI1) for Points Motors with Common Ground
Points Position Indicator (PPI1) for Points Motors with Common Ground Monitors Points Action and Operates Leds on a Control Panel Monitors the brief positive operating voltage across points motors when
MTH SD70ACe DCC Ready Soundtraxx AT-1000 EMD 710 Sound Decoder Install Revised June 1, 2011
303 447-9251 Fax: 303 447-1406 [email protected] Introduction MTH SD70ACe DCC Ready Soundtraxx AT-1000 EMD 710 Sound Decoder Install Revised June 1, 2011 The MTH DCC Ready SD70ACe has very little
LESTRONIC DV AUTOMATIC 12 OR 24 VOLT DUAL OUTPUT DUAL MODE BATTERY CHARGER MODEL 16350 TYPE 12/24EL40-10ET
LESTRONIC DV AUTOMATIC 12 OR 2 VOLT DUAL OUTPUT DUAL MODE BATTERY CHARGER MODEL 16350 TYPE 12/2EL0-10ET PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment,
Cover Page. Factory Radio Other Documents Available For This Vehicle:
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,,2000. Factory Radio
Your Multimeter. The Arduino Uno 10/1/2012. Using Your Arduino, Breadboard and Multimeter. EAS 199A Fall 2012. Work in teams of two!
Using Your Arduino, Breadboard and Multimeter Work in teams of two! EAS 199A Fall 2012 pincer clips good for working with breadboard wiring (push these onto probes) Your Multimeter probes leads Turn knob
SUBJECT: How to wire a motor starter Number: AN-MC-004 Date Issued: 2/08/2005 Revision: Original
SUBJECT: How to wire a motor starter Number: AN-MC-004 Date Issued: 2/08/2005 Revision: Original A motor starter is a combination of devices to allow an induction motor to start, run and stop according
Subaru Reference. This reference contains the following information: connector pinouts. connector pinouts
Subject: Source: 1993 2010 Impreza, WRX, and Sti and 2002 07 Outback Sport ABS wiring diagrams, harness routing, and connector locations and pinouts Subaru service manuals This reference contains the following
Build A Simple Electric Motor (example #1)
PHY115 Experiment 11 Build A Simple Electric Motor (example #1) MATERIAL This is the necessary equipment. Present any list of material in your written lab report. 1.5 V battery in series 1 ceramic magnet
DC Motor control Reversing
January 2013 DC Motor control Reversing and a "Rotor" which is the rotating part. Basically there are three types of DC Motor available: - Brushed Motor - Brushless Motor - Stepper Motor DC motors Electrical
4 LEAD DEDICATED SINGLE PHASE LIMA MAC GENERATOR MODELS 250MSL1185 AND 250MSL1152
4 LEAD DEDICATED SINGLE PHASE LIMA MAC GENERATOR MODELS 250MSL1185 AND 250MSL1152 SERVICE PROCEDURE ELECTRICAL COMPONENT TESTING HI POTENTIAL TETS None of the windings, either rotating or stationary should
TRAIL CHARGER BASED CHARGING SOLUTIONS
TRAIL CHARGER BASED CHARGING SOLUTIONS The Challenge Keeping Auxiliary Liftgate Batteries Charged The performance and proper function of a liftgate depends on an adequately charged auxiliary battery pack.
PUSH BUTTON START INSTALLATION MANUAL
PUSH BUTTON START INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS PRODUCT.
Understanding Generator Ripple Waveforms
Understanding Generator Ripple Waveforms 2 Understanding Generator Ripple Waveforms Chapter Page Preliminary Information and Setup 3 Generator Theory 6 Generator Ripple Theory 15 Factors that Influence
INSTALLATION MANUAL 3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS
3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS INSTALLATION MANUAL Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the
Technical Notes and Workshop Reference.
Technical Notes and Workshop Reference. This reference file has been built up over the last twelve years at Piaggio Ltd, To help with fault finding, assembly understanding and to clarify and expand on
I Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
Using and Wiring Light Emitting Diodes (LEDs) for Model Railroads
Using and Wiring Light Emitting Diodes (LEDs) for Model Railroads LEDs have many useful applications in Model railroading, including: Locomotive headlights Rear-end warning lights for cabooses and passenger
I Click on a link tab to jump to that page. Cover Page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9612 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD FOCUS SE & S MODELS (AT/MT) FORD TRANSIT ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
2007 W-SERIES (CHEVROLET & GMC) N-SERIES (ISUZU) 250 NPR/W3500, NPR HD/W4500, NQR/W5500, NRR/W5500-HD Diesel Electrical Symbols
2007 W-SERIES (CHEVROLET & GMC) N-SERIES (ISUZU) 250 NPR/W3500, NPR HD/W4500, NQR/W5500, NRR/W5500-HD Diesel Electrical Symbols Symbol Meaning Symbol Meaning Symbol Meaning Fuse Electronic Parts Coil (Inductor),
This file is available for free download at http://www.iluvmyrx7.com
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
Solar Home System. User Manual. AEH-SHS01-10W2L Solar Home System 2 Lamps
Solar Home System User Manual AEHSHS0110W2L Solar Home System 2 Lamps All rights reserved Specifications subject to change without prior notice 2 Dear Customer, Thank you for purchasing Schneider Electric
Cable Plug acc. to DIN EN 175301-803, Form A
Cable Plug acc. to DIN EN 175301-803, Form A Complete program Contact form 18 mm Also available with LED indicator Optional 4-pin version for pressure switch or impulse valves respectively Versions with
TOYOTA STARTING SYSTEMS. General
General Starting the engine is possibly the most important function of the vehicle's electrical system. The starting system performs this function by changing electrical energy from the battery to mechanical
4 DEDICATED SINGLE PHASE LIMA MAC GENERATOR LIGHT TOWER DUTY MODELS 250MSL1278 AND 250MSL1299 SERVICE PROCEDURE ELECTRICAL COMPONENT TESTING
HI POTENTIAL TESTS 4 DEDICATED SINGLE PHASE LIMA MAC GENERATOR LIGHT TOWER DUTY MODELS 250MSL1278 AND 250MSL1299 SERVICE PROCEDURE ELECTRICAL COMPONENT TESTING None of the windings, either rotating or
Chapter 5. Components, Symbols, and Circuitry of Air-Conditioning Wiring Diagrams
Chapter 5 Components, Symbols, and Circuitry of Air-Conditioning Wiring Diagrams Objectives Upon completion of this course, you will be able to: Explain what electrical loads are and their general purpose
VOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
Preview of Period 16: Motors and Generators
Preview of Period 16: Motors and Generators 16.1 DC Electric Motors What causes the rotor of a motor to spin? 16.2 Simple DC Motors What causes a changing magnetic field in the simple coil motor? 16.3
ECEN 1400, Introduction to Analog and Digital Electronics
ECEN 1400, Introduction to Analog and Digital Electronics Lab 4: Power supply 1 INTRODUCTION This lab will span two lab periods. In this lab, you will create the power supply that transforms the AC wall
Diode Applications. As we have already seen the diode can act as a switch Forward biased or reverse biased - On or Off.
Diode Applications Diode Switching As we have already seen the diode can act as a switch Forward biased or reverse biased - On or Off. Voltage Rectifier A voltage rectifier is a circuit that converts an
Xenon HID Lighting System
Automotive Safety Systems User Installation Manual Preface Specifications Thank you for purchasing NOVABLUE Xenon H.I.D. (High Intensity Discharge) vehicle lighting systems. Before installing this product,
UNIT 3 AUTOMOBILE ELECTRICAL SYSTEMS
UNIT 3 AUTOMOBILE ELECTRICAL SYSTEMS Automobile Electrical Structure 3.1 Introduction Objectives 3.2 Ignition System 3.3 Requirement of an Ignition System 3.4 Types of Ignition 3.4.1 Battery or Coil Ignition
The $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit.
The $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit. Micro Wizard has been manufacturing Pinewood Derby timers for over 10 years.
Cornerstone Electronics Technology and Robotics I Week 15 Voltage Comparators Tutorial
Cornerstone Electronics Technology and Robotics I Week 15 Voltage Comparators Tutorial Administration: o Prayer Robot Building for Beginners, Chapter 15, Voltage Comparators: o Review of Sandwich s Circuit:
TS510 & TS500. Installation & User Guide. Compatible Equipment
Installation & User Guide Compatible Equipment TS510 REM - Remote Keypad 9040 - Loudspeaker DC54/58 - Digital Communicator SD1+ - Speech Dialler 496525 Issue A 1 of 10 TS510 and TS500 Overview Introduction
Mazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter
MODEL PRO-9744 INSTALLATION MANUAL Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter This System Allows The Transmitter Buttons To Be
Softstart. Changing of Printed Circuit Board PS S18-300. General...2 Please note!... 2
Softstart Changing of Printed Circuit Board PS S18-300 5309 704-1 Rev E Juli-06 General...2 Please note!... 2 Identify the Printed Circuit Board that is going to be replaced...2 Replacing an older PCB
Experiment 2 Diode Applications: Rectifiers
ECE 3550 - Practicum Fall 2007 Experiment 2 Diode Applications: Rectifiers Objectives 1. To investigate the characteristics of half-wave and full-wave rectifier circuits. 2. To recognize the usefulness
ANADOLU UNIVERSITY DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
ANADOLU UNIVERSITY DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EEM 102 INTRODUCTION TO ELECTRICAL ENGINEERING EXPERIMENT 9: DIODES AND DC POWER SUPPLY OBJECTIVE: To observe how a diode functions
AMP Power Series Connectors
May 3, 2011 2011 Tyco Electronics Corporation. All Rights Reserved. TE Connectivity, TE Connectivity (logo) and TE (logo) are trademarks. Other logos, products and/or Company names might be trademarks
ALTERNATOR & REGULATOR - HITACHI
ALTERNATOR & REGULATOR - HITACHI 1990 Nissan 240SX 1990-91 ELECTRICAL Alternators & Regulators - Hitachi 1990 Axxess, Pulsar NX 1991 Maxima, NX, Pathfinder, Pickup, Sentra, Stanza, 240SX & 300ZX NOTE:
I Click on a link tab to jump to that page. Cover Page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
SYSTEM 45. C R H Electronics Design
SYSTEM 45 C R H Electronics Design SYSTEM 45 All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, & A outputs. Independent 25
Essential Electrical Concepts
Essential Electrical Concepts Introduction Modern vehicles incorporate many electrical and electronic components and systems: Audio Lights Navigation Engine control Transmission control Braking and traction
i ChatterBox! Motorcycle Security
i Before you Start the Installation * Please read this manual to become familiar with the requirements necessary to complete the installation. * Use a high quality multi-meter to test all wires before
Installation Instructions
H5HK Series Installation Instructions 3 Phase Electric Heater Kits 7.5 and 0 TON Package A/C Systems Description Installation of 08/40V and 480V H5HK 3 Phase Heater Kits in 7.5 and 0 TON Packaged Air Conditioners.
RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
HYUNDAI ACCENT 2010- /ELANTRA 2012- / KIA RIO 2012- PART NUMBER: 250-9628 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: (AT/MT) VEHICLES RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION
TRANSISTOR/DIODE TESTER
TRANSISTOR/DIODE TESTER MODEL DT-100 Lesson Manual ELENCO Copyright 2012, 1988 REV-G 753115 Elenco Electronics, Inc. Revised 2012 FEATURES Diode Mode: 1. Checks all types of diodes - germanium, silicon,
1R / 4-BUTTON SERIES
Button 1 1R / 4-BUTTON SERIES VEHICLE SECURITY SYSTEM Standard Features: Two 4-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren Dual stage impact detector Remote
INSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE KEYLESS ENTRY MODELS KE100 / KE150 / 1702 CONTENTS System Features... 1 System Components... 1 Technical Assistance... 1 Before You Begin... 1 Precautions... 1-2 Making
DC Circuits (Combination of resistances)
Name: Partner: Partner: Partner: DC Circuits (Combination of resistances) EQUIPMENT NEEDED: Circuits Experiment Board One Dcell Battery Wire leads Multimeter 100, 330, 1k resistors Purpose The purpose
MCT-7 Multiple Cable Test System
www.whirlwindusa.com MCT-7 Multiple Cable Test System INTRODUCTION: The MCT-7 Cable Tester is a versatile unit that allows the user to test almost any pre-made and custom made leads or cables used in a
Battery Chargers. Revised 8/00 Form Number 56041170 FORM NO. 56041170 / BATTERY CHARGER SERVICE MANUAL / PARTS LIST - 45
Battery Chargers SERVICE MANUAL / PARTS LIST AUTOMATIC Advance MODELS 0980, 098, 797, 8809, 90, 880, 880, 099, 08,, 09788, 098, 7, 097, 70, 790, 889 Lester MODELS 007,, 8, 8, 89, 80, 9, 00, 00, 008 MANUAL
Fitting/Installation Guide - UNIVERSAL
ATTENTION: This wiring information is being provided free of charge and on an as is basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with
ANTI-THEFT SYSTEM. 1995 Volvo 850 DESCRIPTION & OPERATION BASIC ALARM. 1995-96 ACCESSORIES & EQUIPMENT Volvo Anti-Theft Systems
ANTI-THEFT SYSTEM 1995 Volvo 850 1995-96 ACCESSORIES & EQUIPMENT Volvo Anti-Theft Systems 850 DESCRIPTION & OPERATION WARNING: Deactivate air bag system before performing any service operation. For 1995
Series and Parallel Resistive Circuits Physics Lab VIII
Series and Parallel Resistive Circuits Physics Lab VIII Objective In the set of experiments, the theoretical expressions used to calculate the total resistance in a combination of resistors will be tested
TEECES DOME LIGHTING SYSTEMS
This lighting system was designed by John V (Teeces) to be a simple, customizable, expandable and affordable solution for dome lighting. An Arduino micro-controller is used to tell LED driver chips which
Part Number: 250-1859
General Applicability 2010 Honda Insight 07- Kia Optima / Forte / Rondo/ 10- Sedona / 12 Soul 10- Hyundai Tucson / Elantra Touring ETC 2012 Accent / Elantra/ Genesis Recommended Tools Safety Tools Gloves,
MANUAL FOR BREAKOUT BOARD HG06
MANUAL FOR BREAKOUT BOARD HG06 INFORMATION IS SPECIFIC TO OUR PRODUCTS AND CAN CAUSE DAMAGE IF USED WITH NONE COMPATIBLE PRODUCTS SO PLEASE CHECK WITH YOUR SUPPLIER FOR COMPATIBILITY These drawings are
Generator Parts List. GXi Part Number. Model Year. 5650,5650EL, 6500, 6500EL, 4550 Pro, 7550EL Pro DEK, STANLEY
G01006 Air check valve for models 2006, G01107 Air filter Air filter module The air filter module comes with all the components ready to be assembled. The module includes the filter cover, filter media,
MGA Alternator Conversion
MGA Alternator Conversion Installation Instructions For 1955 to 1962 MGA PART # 130-078 and #130-088 440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com
2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
PRO PLM Installation Instructions
PRO PLM Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
I Click on a link tab to jump to that page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
INSTALLATION & SERVICE MANUAL. Display Panel
INSTALLATION & SERVICE MANUAL Display Panel The PowerLine EMS TM is a specialized power distribution and energy management system intended to be used in recreational vehicles. The Control Module is housed
GPS & GSM BASED REAL-TIME VEHICLE TRACKING SYSTEM.
GPS & GSM BASED REAL-TIME VEHICLE TRACKING SYSTEM. Introduction: The Proposed design is cost-effective, reliable and has the function of accurate tracking. When large object or vehicles were spread out
1993 ACCESSORIES & EQUIPMENT Volkswagen Instrument Panels. Volkswagen; EuroVan, Passat
Article Text Saturday, March 18, 2000 10:33PM ARTICLE BEGINNING 1993 ACCESSORIES & EQUIPMENT Volkswagen Instrument Panels Volkswagen; EuroVan, Passat DESCRIPTION & OPERATION Instrument cluster for most
WIRING HARNESS FOR AS635P4. BLUE PLUG RED, BLUE, BLACK, WHITE - Plug in dual stage sensor harness
WIRING HARNESS FOR AS635P4 ANTENNA NOT USED 5 PIN WHITE PLUG 2 PIN WHITE PLUG GREEN - PARKING BRAKE INPUT (-) BLUE - NOT USED 3 PIN BLUE PLUG RED, BLUE, BLACK, WHITE - Plug in dual stage sensor harness
WARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE
INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8
1978-83 Malibu 1978-87 Monte Carlo 1978-87 El Camino
Important facts about this kit. 1. The dash panel used in this picture is used by permission of Covan's Classic. 2. This kit requires some modification to your original under dash wiring harness. It is
LMU-5000. Hardware and Installation Guide
LMU-5000 Hardware and Installation Guide Plan The Installation Verify Power, Ground and Ignition. Be sure to check each source (power, ground and ignition) to ensure that the proper signaling exists. This
HOW TO CORRECTLY CONNECT DEEP CYCLE BATTERIES AND CHOOSE THE RIGHT CABLE SIZING
HOW TO CORRECTLY CONNECT DEEP CYCLE BATTERIES AND CHOOSE THE RIGHT CABLE SIZING There are several ways to wire multiple batteries to achieve the correct battery voltage or capacity for a particular DC
Alternating Current and Direct Current
K Hinds 2012 1 Alternating Current and Direct Current Direct Current This is a Current or Voltage which has a constant polarity. That is, either a positive or negative value. K Hinds 2012 2 Alternating
HONDA ACCORD 1985-2005
HONDA ACCORD 1985-2005 VEHICLE WIRING Copyright 2002-2004 Triple S Customs WIRING INFORMATION: 1985 Honda Accord WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WHITE or WHITE/BLACK Ignition Harness STARTER
Tutorials Drawing a 555 timer circuit
Step 1 of 10: Introduction This tutorial shows you how to make an electronic circuit using Livewire and PCB Wizard 3. You should follow this tutorial to learn the basic skills you will need to use Livewire
Odyssey of the Mind Technology Fair. Simple Electronics
Simple Electronics 1. Terms volts, amps, ohms, watts, positive, negative, AC, DC 2. Matching voltages a. Series vs. parallel 3. Battery capacity 4. Simple electronic circuit light bulb 5. Chose the right
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 Control a relay by means of the wellknown DMX512 protocol. ILLUSTRATED ASSEMBLY MANUAL H8072IP-1 Features
tidesmarine Smart Seal Temperature Alarm System Generation II Installation Instructions Starboard side cable
tidesmarine Smart Seal Temperature Alarm System Generation II Installation Instructions Starboard side cable Port side cable (with black cable tie attached) Power cable Preparing for Installation 1 Overall
6. Diagnostics for A/C System Malfunction
6. A: A/C OR SELF-DIAGNOSIS SYSTEMS DO NOT OPERATE TROUBLE SYMPTOM: Set temperature is not indicated on the display, switch LEDs are faulty or switches do not operate. Self-diagnosis system does not operate.
3.- What atom s particle moves through a conductor material? 4.- Which are the electric components of an elemental electric circuit?
1.- What is electricity? 2.- Write down the name of the atom s particles. 3.- What atom s particle moves through a conductor material? 4.- Which are the electric components of an elemental electric circuit?
Snap-It. This is an accessory (switch machine) decoder
Snap-It $19.95 For use with most twin coil switch machines such as: Atlas, LifeLike, Peco, Bachmann, NJ, Rix, Kemtron and others Dimensions: 1.80" x 1.50" (46 x 38 mm) This is an accessory (switch machine)