DESIGN NOTES WELDING NOTES WELDERS & WELDING PROCEDURES ARE QUALIFIED TO API-1104 RADIOGRAPHY 0.72 DESIGN FACTOR 100% BUTT WELDS PER API-1104 WITH
|
|
|
- Godwin Newman
- 9 years ago
- Views:
Transcription
1 GENERAL NOTES:. ALL AUILIARY TUBING DESIGN MUST FOLLOW MARATHON STANDARD TNLDGN00. ALL SWAGELOK TUBE FITTINGS MUST BE ASSEMBLED USING POCKET INSTALLATION MANUAL. AUILIARY TUBING ASSEMBLIES SHALL BE SHOP PROOF TESTED AT A MINIMUM OF 00 PSI FOR AT LEAST 0 MIN.. REFER TO MARATHON STANDARD TNLCON00 FOR BOLTS AND GASKETS FOR FLANGED CONNECTIONS FOR TORQUE REQUIREMENTS. STUD BOLTS SHOULD BE TORQUED IN A CROSS/STAR PATTERN IN 0% INCREMENTS WITH A TORQUE WRENCH. GASKETS SHALL BE REPLACED AFTER HYDRO FIT UP, OR ANY FIT UP THAT IS DISADDEMBLED, GASKETS CAN NOT BE REUSED. FOLLOW MARATHON STANDARD MPLDGN00 FOR HYDRO TEST DESIGN AND DOCUMENTATION WHICH INCLUDES COMPLETING THE PROPER PAPER WORK AFTER AND DURING HYDRO TESTING INCLUDING MARATHON'S PL-0 DOCUMENTATION FORM. DRY ALL PIPELINE AFTER HYDRO AND DRAIN ALL VALVE BODIES. FOLLOW MARATHON STANDARD TNLCON0 FOR PAINT AND TANK LINING SYSTEMS. FOLLOW SECTION. OF SCOPE FOR ALL INSPECTION & TESTING 0. RED TAGS SHOULD BE ATTACHED TO CLOSED ENDS FOR SHIPMENT WITH WARNING ABOUT PRESSURE. WRITTEN PROCEDURES FOR LOADING, SHIPPING, AND UNLOADING OF TRAPS SHOULD BE FOLLOWED. PROPERLY SECURE TRAPS FOR TRANSPORTATION WITH NON-METAL STRAPS AND BLOCKING. FULLY ASSEMBLE AND PAINT BEFORE HYDRO TEST 0 - P.O. # --00 LINE THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. (TOLERANCES ± /) / (TYP) IEW DT CHECK WELDS IEW -RAY IEW NDE SURFACE PREP/PAINT SHIPMENT / FINAL OTHER TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± 00 TO 0 PSIG B. PRESSURE TO PSIG NITROGEN BA00 EPOLON II RUST INHIBITIVE EPOY PRIMER - MILS DFT BA00 EPOLON II RUST INHIBITIVE EPOY PRIMER - MILS DFT BW00 HI-SOLIDS POLYURETHANE: - MILS DFT 0 x SKID MOUNTED LAUNCHER D VIEW - A DWG BY: JS WEIGHT:,0 LBS SHEET OF
2 DETAIL A SCALE : 0'-0 0'- '- '- 0 A '-0 0 '- '- '- PTI PIT '- '- '- '- '- '- '- '- '- 0'- '- '- '- '-0 '- '- '- 0'- '-0 PI 0'- NOTE TV '-0 PI '- '- '- 0'- '- '- '-0 '-0 REPRESENTS THE SHIPPING CENTER OF GRAVITY OF THE TRAP. SHIPPING CENTER REPRESENTS ALL MATERIAL ON THE TRAP ECEPT THE FOLLOWING S THAT WILL BE SHIPPED SEPARATLEY.... ALL STAIRS GATE VALVE ACCESS PLATFORM PLATFORM THAT ATTACHED TO THE SIDE '- ' / (TYP) (TOLERANCES ± /) 0 IEW NDE '- IEW -RAY '- IEW DT CHECK WELDS SURFACE PREP/PAINT SHIPMENT / FINAL OTHER '- '- TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 '-0 '- DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± '- '- 00 TO 0 PSIG B. PRESSURE TO PSIG NITROGEN B P.O. # --00 LINE DETAIL B SCALE :.. BA00 EPOLON II RUST INHIBITIVE EPOY PRIMER - MILS DFT BA00 EPOLON II RUST INHIBITIVE EPOY PRIMER - MILS DFT BW00 HI-SOLIDS POLYURETHANE: - MILS DFT NOTES ALLOW FOR SLOPE OF / PER ' AWAY FROM CLOSURE BY ADJUSTING PIPE SUPPORT HEIGHT HAND WHEEL FOR BOTH BALL SHOULD BE LOCATED ON THIS SIDE THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. 0 x SKID MOUNTED LAUNCHER PIPING PLAN - A DWG BY: JS WEIGHT: SHEET OF
3 A B A B C PIPE CUT LIST 0 - (TOLERANCES ± /) A B / (TYP) QTY DESCRIPTION CUT LENGTH PIPE, 0 O.D., 0.00 W.T., '- / PIPE, 0 O.D., 0.00 W.T., '-0 PIPE, O.D.,. W.T., PIPE, O.D.,. W.T., PIPE, O.D.,. W.T., '- / '- '- / B B / IEW -RAY IEW NDE 0 PART PO. TAG C B IEW DT CHECK WELDS SURFACE PREP/PAINT SHIPMENT / FINAL OTHER A B Pipeline Equipment, Inc. TULSA DESIGN CODE MA W.P. TEST PRESSURE CORROSION ALLOW DRY WEIGHT OKLAHOMA NAMEPLATE DETAIL PLACE ON SKID PIPE CUT LIST QTY DESCRIPTION CUT LENGTH A PIPE,.0 O.D.,. W.T., SMLS / B PIPE,.0 O.D.,. W.T., SMLS '- A PIPE,. O.D.,. W.T., B PIPE,. O.D.,. W.T., '-0 C PIPE,. O.D.,. W.T., YR BUILT TEMP 0 TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 C 0 DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± 0 B NOTES 00 TO 0 PSIG B. 0 PROVIDE / PER ' SLOPE AWAY FROM CLOSURE BY ADJUSTING PIPE SUPPORT HEIGHT A A 0 PRESSURE TO PSIG NITROGEN MARATHON PIPLINE P.O. # --00 LINE STUD BOLT, / / LG. w/ () HE NUTS EA. (-0#) A- B A- H FLANGE,, 0 LBS., RFWN, STD BORE A-0 GR. B FLANGE,, 00 LBS., BLIND A-0 GR. B FLANGE,, 0 LBS., BLIND A-0 GR. B 0 FLANGE,, 00 LBS., BLIND A-0 GR. B FLANGE,, 00 LBS., BLIND MSS-SP- F- FLANGE,, 00 LBS., BLIND MSS-SP- F- FLEITALLIC 0# TYPE CGI 0 SS GASKET 0/FLEITE THREADOLET, NOM. ON, 000# A-0 GR. B PIPE NIPPLE, / NOM. x LG., SCH 0 T.B.E. A-0 GR. B T.D. WILLAMSON 0-00 LB., CLOSURE PART , w/ BORE AND FLANGE, ASME TDW D000 HE PLUG, / NOM., 000 LB., THRD, F.S. A-0 HE PLUG, NOM., 000 LB., F.S. A-0 T.D. WILLIAMSON PG-SIG IV W/ COMBINATION FLAG PART SST 0 T.D. WILLIAMSON PIG-SIG IV W/ MANUAL FLAG RESET PART SST VALVE, BALL, / 000 LB., THRD WKM VALVE, BALL, 00 LB., RFFE ORBIT VALVE, BALL, 00 LB., HAND WHEEL OP. ORBIT VALVE, GATE, 00 LB. RFFE, W/ ELECTRIC MOTOR ACTUATOR M&J VALVE, EPANDING GATE, 00 LB. RFFE, W/ ELECTRIC MOTOR ACTUATOR M&J VALVE, EPANDING GATE, 00 LB. RFFE, W/ ELECTRIC MOTOR ACTUATOR M&J THREADOLET, NOM., 000 LB., A-0 GR. B THREADOLET, / NOM., 000 LB., A GR. F WELDOLET,, STD. WT. A GR. F 0 WELDOLET,, STD. WT. A GR. F WELDOLET, 0, H. WT. A GR. F WELDOLET, 0, H ON STD. WT. A GR. F STUD BOLT, / / LG. w/ () HE NUTS EA. (-00#) A- B A- H STUD BOLT, / LG. w/ () HE NUTS EA., (-00#) A- B A- H 0 STUD BOLT, / / LG. w/ () HE NUTS EA. (-00#) A- B A- H 0 STUD BOLT, / LG. w/ () HE NUTS EA. (-00#) A- B A- H STUD BOLT, / / LG. w/ () HE NUTS EA. ( -00#) A- B A- H STUD BOLT, / LG. w/ () HE NUTS EA. (0-00#) A- B A- H FLEITALLIC 00# TYPE CGI 0 SS GASKET 0/FLEITE 0 FLEITALLIC 00# TYPE CGI 0 SS GASKET 0/FLEITE FLEITALLIC 00# TYPE CGI 0 SS GASKET 0/FLEITE FLEITALLIC 00# TYPE CGI 0 SS GASKET 0/FLEITE FLEITALLIC 0 00# TYPE CGI 0 SS GASKET 0/FLEITE FLEITALLIC 00# TYPE CGI 0 SS GASKET BA00 EPOLON II RUST INHIBITIVE EPOY PRIMER - MILS DFT BA00 EPOLON II RUST INHIBITIVE EPOY PRIMER - MILS DFT BW00 HI-SOLIDS POLYURETHANE: - MILS DFT THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. 0 x SKID MOUNTED LAUNCHER PIPING 0/FLEITE FLANGE, 00 LB., RFWN, STD BORE A-0 GR. B FLANGE,, 00 LB., RFWN, STD BORE A-0 GR. B FLANGE,, 00 LB., RFWN, STD BORE A-0 GR. B FLANGE, 00 LB., RFWN,. BORE MSS-SP- F- FLANGE,, 00 LB., RFWN,. BORE MSS-SP- F- 0 FLANGE, 0, 00 LB, RFWN,.00 BORE MSS-SP- F- ELL,, H WT., LR, 0 A- GR. WPB ELL,, STD W.T., LR., 0 A- GR. WPB REDUCER, ECC., 0 H x STD W.T. MSS SP- WPHY- TEE, REDUCING,, STD W.T., w/scraper BARS MSS SP- WPHY- TEE, REDUCING, 0, H x STD., w/ SCRAPER BARS MSS SP- WPHY- PIPE,. O.D.,. W.T., SMLS API L GR. B PIPE,.0 O.D.,. W.T., SMLS API L GR. B PIPE, O.D.,. W.T.,ERW API L- PIPE, 0 O.D., 0.00 W.T., DSAW API L- - A DWG BY: JS WEIGHT:,00 lbs SHEET OF
4 DETAIL PI PRESSURE INDICATOR 00 LB () REQ DETAIL PT PRESSURE TRANSMITTER 00 LB () REQ 0 - TOWARD PIT ' / DETAIL TV THERMAL RELIEF VALVE 00 LB () REQ TOWARD PT ' / CONNECTED TO PT 0 DETAIL PIT PRESSURE TRANSMITTER PIT-00 () REQUIRED MOUNTED TO H BEAM 0 0, 000# NPT, THRD., LADISH 0 ELBOW #0 ASTM A-0 NOM. x LG. PIPE NIPPLE, TBE, SCH 0 ASTM A-0 000# LADISH FULL THRD. COUPLING # ASTM A-0 / O.D. 0.0 W.T., SWAGELOK SS-TB-S-0-0 SS ROSEMONT PRESSURE TRANSMITTER #0STGAEAABDEM SWAGELOK #SS-0-- SS NIPPLE, / NOM. /, SCH 0, TBE 0SS SWAGELOK #SS-0-- SS SWAGELOK #SS-0-- SS SWAGELOK #SS-QF-S-PM w/ STEM PROTECTOR CAP #SS-QF-SP SS 0 SWAGELOK #SS--SE SS SWAGELOK #SS-PDGM-F SS ASHCROFT PRESSURE GAUGE SS SWAGELOK #SS-RMS-C SS SWAGELOK #SS--P SS SWAGELOK #SS-0VF SS SWAGELOK #SS--HRN- SS SWAGELOK #SS-QC-D-PM w/ STEM PROTECTOR CAP #SS-QC-SP w/ DOUBLE END SHUT-OFF SS SWAGELOK #SS-PDM-F SS SWAGELOK #SS--RB- SS QTY. PART NUMBER MATERIAL P.O. # --00 LINE THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. (TOLERANCES ± /) / (TYP) IEW -RAY IEW NDE IEW DT CHECK WELDS SURFACE PREP/PAINT SHIPMENT / FINAL OTHER TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 DESIGN CODE DESIGN PRESS. DESIGN TEMP. CORR. ALLOW. ± CFR Part 0. 0 PSI 00 F NONE TOLERANCES PER PFI ES- 00 TO 0 PSIG B. PRESSURE TO PSIG NITROGEN BA00 EPOLON II RUST INHIBITIVE EPOY PTIMER - MILS DFT BA00 EPOLON II RUST INHIBITIVE EPOY PRIMER: - MILS DFT BW00 HI-SOLIDS POLYURETHANE: - MILS DFT 0 x SKID MOUNTED REICEVER INSTRUMENTATION DETAIL - DWG BY: JS WEIGHT: A SHEET OF
5 JUNCTION BOES 0 A DETAIL A SCALE : 0 '-0 '- 0'-0 B 0 0 '-0 '-0 '- '- '-0 '- '- '- '-0 NOTE:. ALL E-Z LINE SUPPORTS WILL BE WELDED TO THE STRUCTURAL SKID. PIPE SHOULD BE COATED WITH #0 FRP ROLL-ON SHIELD WHERE CONTACTED WITH PIPE SUPPORT. FRP TO BE BONDED TO THE PIPE WITH EPI SEAM SEALER 0 - (TOLERANCES ± /) / (TYP) '- '- '- '- '-0 IEW -RAY IEW NDE 0'- '- '-0 IEW DT CHECK WELDS '-0 SURFACE PREP/PAINT SHIPMENT / FINAL OTHER '- '- '- '- TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 '- GRATING x SERRATED 0'- '- '- DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± '- DETAIL B SCALE : '-0 ANGLE L x x / x '-0 A- ANGLE L x x / x '- / A- PLATE, PL '- x '-0 x THK. A- S BEAM x. x '-0 LG. A- 0 E-Z LINE PIPE SUPPORT E-Z LINE PIPE SUPPORT Wx x '-0 A- 0 U-BOLT FOR NOM. PIPE, ZINK PLATED A- ANGLE L x x / x 0'- A- ANGLE L x x / x '- / A- ANGLE L x x / x '- / A- 0 Wx x '- A- Wx x '-0 A- Wx x ' / A- Wx x '- / A- Wx x '-0 / A- Wx x '-0 A- Wx x '- / A- Wx x '- / A- Wx x '- / A- Wx x '- / A- 00 TO 0 PSIG B. THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. P.O. # --00 LINE 0 x SKID MOUNTED LAUNCHER SKID - A DWG BY: JS WEIGHT: 00 LBS SHEET OF
6 '- 0'- '- '-0 0'- 0'- '- '-0 '-0 '- '- '- '- '- 0 0 '-0 '- '-0 '- '-0 '- '- '- '- '-0 '- '- '- 0'- '- GRATING SERRATED 0'-0 GRATING SERRATED '- '- 0'-0 '- '-0 '- '- GRATING SERRATED '-0 0 '- 0'- 0-0 '- '- '- '- '- '- '- 0'- '- '- P.O. # --00 LINE THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. (TOLERANCES ± /) / (TYP) IEW NDE IEW -RAY IEW DT CHECK WELDS SURFACE PREP/PAINT SHIPMENT / FINAL OTHER TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± 00 TO 0 PSIG B. 0 x SKID MOUNTED LAUNCHER PLATFORM - A DWG BY: JS WEIGHT: SHEET OF
7 SQUARE TUBING TS x x / x '-0 / A- ANGLE L x x / x '-0 A- ANGLE L x x / x '- / A- ANGLE L x x / x '-0 / A- ANGLE L / x / x / x '- A- ANGLE L x x / x '- / A- ANGLE L x x / x '- A- ANGLE L x x / x '-0 / A- SQUARE TUBING TS x x / x / A- SQUARE TUBING TS x x / x '- / A- FB x / x A- FB x / x '-0 A- FB x / x '-0 A- ANGLE L x x / x '- / A- ANGLE L x x / x '- / A- 0 ANGLE L x x / x '-0 / A- ANGLE L x x / x '-0 / A- ANGLE L x x / x '- / A- ANGLE L x x / x 0'-0 A- 0 ANGLE L / x / x / x '- A- ANGLE L x x / x '- A- ANGLE L x x / x '-0 A- ANGLE L x x / x '-0 A- ANGLE L x x / x '- A- ANGLE L x x / x 0'-0 A- 0 0 CATCH BASIN GATE VALVE ACCESS PLATFORM WEIGHT: 00 LBS 0 - CLOSURE ACCESS PLATFORM WEIGHT : 0 LBS P.O. # --00 LINE THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. (TOLERANCES ± /) / (TYP) IEW DT CHECK WELDS SURFACE PREP/PAINT IEW -RAY SHIPMENT / FINAL IEW NDE OTHER TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± 00 TO 0 PSIG B. 0 x SKID MOUNTED LAUNCHER PLATFORM DETAIL - A DWG BY: JS WEIGHT: SHEET OF
8 0 0 - & GATE VALVE ACCESS PLATFORMS WEIGHT: 00 LBS ANGLE L x x / x '- A- SQUARE TUBING TS x x / x '- A- SQUARE TUBING TS x x / x '- / A- SQUARE TUBING TS x x / x '- A- SQUARE TUBING TS x x / x '- A- ANGLE L x x / x '-0 A- ANGLE L x x / x '- / A- ANGLE L x x / x '- A- 0 ANGLE L x x / x '-0 / A- ANGLE L x x / x '- / A- 0 ANGLE L / x / x / x '- A- ANGLE L x x / x '- A- ANGLE L x x / x '- A- ANGLE L x x / x '- A- ANGLE L x x / x '- A- ANGLE L x x / x '- / A- ANGLE L x x / x '- A- ANGLE L x x / x '- / A- P.O. # --00 LINE THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. (TOLERANCES ± /) / (TYP) IEW DT CHECK WELDS IEW -RAY IEW NDE SURFACE PREP/PAINT SHIPMENT / FINAL OTHER TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± 00 TO 0 PSIG B. 0 x SKID MOUNTED LAUNCHER PLATFORM DETAIL DWG. B - A DWG BY: JS WEIGHT: SHEET OF
9 0 ANGLE L x x / x '-0 A- HE HEAD BOLT, / DIA. x / LG., w/ () HE NUT EA. ANGLE L x x / x '- A- ANGLE L x x / x '-0 A- ANGLE L x x / x '- / A- 0 ANGLE L x x / x / A- ANGLE L x x / x '- / A- CHANNEL C x. x '- / A- 0 ANGLE L x x / x '-0 A- HE HEAD BOLT, / DIA. x / LG., w/ () HE NUT EA. ANGLE L x x / x '- A- 0 ANGLE L x x / x / A- ANGLE L x x / x '-0 A- ANGLE L x x / x '- / A- ANGLE L x x / x '- / A- CHANNEL C x. x '- / A- '- TYP. '-0 '- 0 '- '-0 '- 0 '- TYP. TYP. END STAIRS WEIGHT: LBS. '-0 TYP. MIDDLE STAIRS WEIGHT: LBS. ' P.O. # --00 LINE THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. (TOLERANCES ± /) / (TYP) IEW DT CHECK WELDS SURFACE PREP/PAINT IEW -RAY SHIPMENT / FINAL IEW NDE OTHER TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± 00 TO 0 PSIG B. 0 x SKID MOUNTED LAUNCHER STAIRS DETAIL - A DWG BY: JS WEIGHT: SHEET OF
10 0 ANGLE L x x / x '-0 A- SAFETY CHAIN ANGLE x x / x '- A- ANGLE x x / x '- / A- ANGLE x x / x '- / A- ANGLE x x / x '- / A- HE HEAD BOLT, / DIA. x / LG., w/ () HE NUT EA. PLATE, x x / THK. A- SQUARE TUBING TS x x / x '- / A- ANGLE L x x / x / A- 0 ANGLE x x / x '- / A- ANGLE L x x / x '-0 A- ANGLE x x / x '-0 A- ANGLE L x x / x '- / A- ANGLE L x x / x '- / A- ANGLE / x / x / x '- A- ANGLE x x / x '- A- ANGLE x x / x '- A- ANGLE x x / x '- / A- CHANNEL C x. x '- / A- QTY. DESCRIPTION MATERIAL 0 0 '- '- '- '- '-0 TYP. 0 '-0 0 '- TYP. TYP. SIDE STAIRS WEIGHT: LBS. THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. 0 - (TOLERANCES ± /) / (TYP) IEW DT CHECK WELDS SURFACE PREP/PAINT IEW -RAY SHIPMENT / FINAL IEW NDE OTHER TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± 00 TO 0 PSIG B. 0 x SKID MOUNTED LAUNCHER STAIRS DETAIL -0 A DWG BY: JS WEIGHT: SHEET 0 OF
11 '- '- UP 0 R / '- '- UP 0 R / UP 0 R / '- '- UP 0 R / '- CATCH BASIN 0 - HANDLE, / '-0 WIDE w/ MOUNTING PLATE SHEET METAL, 0 GA., '- x '- SHEET METAL, 0 GA., '- / '- / THIS DRAWING PROPERTY OF PIPELINE EQUIPMENT, INC. THE INFORMATION IS NOT TO BE USED ECEPT AS EPRESSLY AUTHORIZED P.O. # --00 BY THIS COMPANY. COPIES ARE NOT TO BE MADE WITHOUT PERMISSION. LINE (TOLERANCES ± /) / (TYP) IEW DT CHECK WELDS SURFACE PREP/PAINT IEW -RAY SHIPMENT / FINAL IEW NDE OTHER TO API-0 00% BUTT WELDS PER API-0 WITH ACCEPTANCE PER API-0 DESIGN CODE CFR Part 0. DESIGN PRESS. 0 PSI DESIGN TEMP. 00 F TOLERANCES PER PFI ES- ± 00 TO 0 PSIG B. 0 x SKID MOUNTED LAUNCHER CATCH BASIN - A DWG BY: JS WEIGHT: SHEET OF
CALCULATION & DRAFTING STANDARDS MANUAL PROCEDURE: C&D 515 Bill of Materials Standard REV 0.0 5/6/04
BROWN MINNEAPOLIS TANK PAGE 1 OF 7 PURPOSE: Create and Drawing Uniformity Create, explain, and establish a standard bill of materials to be placed on every drawing (except the overall tank elevation and
OPERATING and MAINTENANCE MANUAL SERIES 2700A CONTROL VALVE CONTENTS. INTRODUCTION...1 Scope...1 Description...1 Valve Identification...
OPERATING and MAINTENANCE MANUAL SERIES 2700A CONTROL VALVE CONTENTS INTRODUCTION...1 Scope...1 Description...1 Valve Identification...2 1.0 VALVE INSTALLATION...2 2.0 VALVE MAINTENANCE...3 Actuator Disassembly...3
PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification. 96 B. Riutta
PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification Number: 3503-11.2.610 Rev. 2 Rubber Lined Steel Pipe and Fittings Mechanically Coupled Plain End Type System Issued Revised Approved
James M. Pleasants Company
James M. Pleasants Company SUBMITTAL DATA GAINESVILLE MECHANICAL DECEMBER 20, 2013 PROJECT: GSU: J-183 HUMANITIES LAW BLDG. QUOTE NO:12116 ENGINEER: STEVENS & WILKINSON GASKETED PLATE HEAT EXCHANGER Tag:
Stainless Steel Valves For the Sanitary Industries
www.swagelok.com Stainless Steel Valves For the Sanitary Industries Sanitary ball valves Manual and pneumatically actuated butterfly valves Disk and ball check valves ir blow check valves ir relief valves
ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.
ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.4-1998 - Cast Iron Threaded Fittings ASME/ANSI B16.5-1996 - Pipe
LOT DETAILS FOR 672BZ-1016
DESCRIPCION LARGA FABRICANTE CENTRO SECTOR LICENCIA LINEA CÓDIGO VALVE~TYPE:EMERGENCY SHUTDOWN~VALVE SIZE:9IN~PRESSURE RATING:10000LB~MATERIAL SPECIFICATION:ASTM A487~GRADE:1CLC VALVE BALL VALVE SIZE:16
Valve Live Loading With Belleville Springs. Belleville Springs for Valve Live Loading
Valve Live Loading With Belleville Springs What is Valve Live Loading? The addition of Belleville Springs to the gland follower studs to maintain the packing load of the valve over time. What s In The
FLANGED END BALL VALVE
Specification: FLANGED END BALL VALVE - Chem Oil s two-piece ball valve has been designed to handle extreme service applications with unsurpassed reliability. Valve body machined from solid wrought material
Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks
TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
INDICATOR POST STYLE 2945 A TELESCOPING BARREL ASSEMBLY UL AND FM APPROVED
INDICATOR POST STYLE 2945 A TELESCOPING BARREL ASSEMBLY UL AND FM APPROVED Available in Sizes B C D E See Page 6 for Dimensions Kennedy Valve/Indicator Posts 17-1 INDICATOR POST STYLE 2945 A TELESCOPING
DARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
SECTION 15062 STEAM AND CONDENSATE PIPING PART 1 DESIGN DIRECTIVES 1.1 QUALITY ASSURANCE A. Comply with the provisions of the following: 1.2 DESIGN CRITERIA 1. ASME B 31.9 Building Services Piping : for
Float and Thermostatic Traps Series H, C and X
Hoffman Specialty Installation & Maintenance Instructions HS-(E) and Thermostatic Traps Series H, C and X Series C & NPT Series C NPT Series X NPT Series C NPT Series H Ratings Maximum Max. Operating NPT
TITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
Pressure Vessel Assessment Report
Project Information Client: Total Energy Location: Blackwell OK Date: 7/23/2013 Contact: Integrity Mgmt. Advisor: Chuck Easterbrooks - API 510 #2212 Cc: API / UT Inspector: Robert Van Pelt-API 510# 40899
valve solutions Chemical Cosmetic Cryogenic Food & Beverage Marine Mining Nuclear Oil & Gas Paint Pharmaceutical Pulp & Paper www.quilinox.
valve solutions www.quilinox.com Chemical Cosmetic Cryogenic Food & Beverage Marine Mining Nuclear Oil & Gas Paint Pharmaceutical Pulp & Paper valvulas esfera PBM.pdf (1753) 2015/01 1/10 D E SIGN F E A
Valves, Automation & Controls. series 84 /99 HIGH PERFORMANCE 3-PIECE BALL VALVE REDUCE & FULL PORT, STANDARD & FIRE SAFE. www.sharpevalves.
Valves, Automation & Controls series 8 /99 & FS8 /FS99 HIGH PERFORMANCE -PIECE BALL VALVE REDUCE & FULL PORT, STANDARD & FIRE SAFE www.sharpevalves.com Design & Features SHARPE VALVES - SERIES 8/99 Fire
Installation, Operation and Maintenance Manual for Pilot Operated Valves
Installation, Operation and Maintenance Manual for Pilot Operated Valves Models 1400, 1420, 1430, 1460 IOM1400.0 January 2, 2014 REV A 12393 REF. ID 98136 IOM1400.0 REV. A 12541 TABLE OF CONTENTS DESCRIPTION
EAGLE ASSET TRACKING DATABASE
EAGLE ASSET TRACKING DATABASE Eagle Inspection Technologies offers a user friendly Asset Tracking Database designed specifically for small industrial facilities (Power Plants, Chemical Plants, Tank Farms,
MODEL G300 BRAKE BLEEDER
MODEL G300 BRAKE BLEEDER Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV060616 P/N: 81-0035G 1 THIS PAGE INTENTIONALLY
Telescoping Post Indicator Wall Post KENNEDY VALVE ISO 9000 ISO 14001
Telescoping Post Indicator Wall Post KENNEDY VALVE ISO 9000 ISO 14001 Telescoping Post Indicator 2945 A 1" SQUARE STEM 9" MAX. = 10" MIN. = 7" FIELD ADJUSTMENT INSTRUCTIONS 1. Remove the top section from
TYPE E Main Valve Sizes 3 /8 through 12
SD 3001F PRINTED IN U.S.A. SD 3001F/0707 A B TYPE E MAIN VALVE C D E TYPE E Main Valve Sizes 3 /8 through 12 The Spence Type E Main Valve is of normally closed, single seat design featuring packless construction,
Copper Meter Resetters
Copper Meter Resetters To Set 5/8", 5/8" x 3/4", 3/4", 1", 1 1 2" & 2" Water Meters 11/12 Table of Contents Page Page Meter Resetters 5/8", 5/8" x 3/4", 3/4", & 1" Horizontal Inlet and Outlet Series 710
ISORIA. Centered disc butterfly valves with AMRING elastomer liner. 240 PSI: 1½ to8. 150 PSI : 10 to 24
Type series booklet 8448.1/2-EN--US ISORIA Centered disc butterfly valves with AMRING elastomer liner 240 PSI: 1½ to8 150 PSI : 10 to 24 Design in accordance with ISO 10631 Manual, electrical, pneumatical
RMF Engineering 23 05 23
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
GAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES
GAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES CONTINENTAL INDUSTRIES ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and is today
www.klmtechgroup.com TABLE OF CONTENTS
Page : 1 of 216 TABLE OF CONTENTS 1 GENERAL 2 1.1 Scope 2 1.2 Code and s 2 1.3 Pressure-Temperature Design 6 1.4 Pipe Wall Thickness Allowance 7 1.5 Ends 8 1.6 Units 8 1.7 Language 9 2 MATERIAL 9 2.1 General
5.23.22 STEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD PART 1: GENERAL. 1.01 Purpose:
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
SECTION 33 12 19 FIRE HYDRANTS
SECTION 33 12 19 FIRE HYDRANTS PART 1: GENERAL 1.01 SCOPE A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. 1.02 SUBMITTALS A. Conform to requirements of Section 01 33 00 - Submittals.
V47 Series Temperature Actuated Modulating Water Valves
V47 Series Temperature Actuated Modulating Water Valves Master Catalog 125 Valves, Miscellaneous (Other Than Gas) Section V Product Bulletin V47 Issue Date 0286 Application The V47 modulating valves regulate
Style 07 Zero Flex Rigid Coupling. Style 75 Flexible Coupling. Style 77 Flexible Coupling 11. Description
Style 07 Zero Flex Rigid Coupling The unique angled pad design adjusts to standard pipe tolerances to positively clamp the pipe to resist flexural and torsional loads. Working pressures are based on standard
SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE
SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel
Valves dimension of pressure (lbs) ANSI2500 ANSI1500 ANSI900 ANSI600 ANSI300 ANSI150. Inch. from 1/2 up to 6
+SBF CARBON STEEL Type: ball valve SBF ANSI B16.5 Body: round Material: A105/F316 Ball seats: from DN13 up to DN150 O-Rings: NBR, FKM, EPDM, MVQ Operating pressure: 20 Bar - 50 Bar - 100 Bar 150 Bar -
RING JOINT SYSTEMS 207
RING JOINT SYSTEMS 07 08 Table of Contents Model R-88 Pages 10-11 Model R-88 Large Diameter Page 1 Model RH-1000 1000 PSI Coupling Page 13 Model RX-3000 3000 PSI Coupling Page 1 Model RX-3770 3770 PSI
ENGINEERED & PROCESS VALVES. Installation, Operation and Maintenance Manual GENERAL VALVE. Twin Seal Double Block and Bleed Plug Valve GENERAL VALVE
GENERAL VALVE Twin Seal Double Block and Bleed Plug Valve GENERAL VALVE 2 TABLE OF CONTENTS GENERAL VALVE TWIN SEAL Installation.... 4 Operation.... 5 Series 400, 800 & 900 Integral Bushing/Retained Ring
Toroidal Conductivity Sensor
Instruction Sheet PN 51A-/rev.C June 2012 Toroidal Conductivity Sensor For additional information, please visit our website at www.emersonprocess.com/rosemountanalytical.com SPECIFICATIONS Wetted Materials:
www.klmtechgroup.com TABLE OF CONTENT
Page : 1 of 10 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia TABLE OF CONTENT SCOPE 2 REFERENCES
2
10 MECHANICAL DRIVE SWING AWAY AUGER PARTS LIST SERIAL NOS. 70000-74773 1 2 # PART # DESCRIPTION 1 B198362 Boot Access Cover 2 B030500 Side Wind Jack 3 B003049 PTO Shaft - Constant Velocity 4 B027504 Boot
Cajon VCR Fittings. Flanges, Fittings, & Components. Cajon & Swagelok Fittings. Cajon VCR Fittings. Nuts, Caps, & Plugs. Socket Weld Glands
Cajon VCR Fittings Cajon VCR Fittings Make excellent low-pressure gas connections Ideal for lecture bottle gas cylinders, standard helium checks, and general gas plumbing Withstand bakeout to 58º C (with
DENVER MODEL 30 X 30 SPECIFICATIONS
DENVER MODEL 30 X 30 SPECIFICATIONS Dimensions: Roof Dimensions 30-0 x 30-0 (4) Columns (Center to Center) 25-6½ x 25-6½ Minimum Clearance 8-0 Roof Height @ Peak Dependent on Col. Ht. Hip Roof 4:12 pitch
Mueller. Pipe Repair Products. Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source.
Mueller Pipe Repair Products Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source. SERVICE SADDLES Mueller service saddles, available in bronze,
Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
HK Trading Import Export e.k. is a family owned German company. Founded in 2004 HK Trading has established itself as a notable trading company.
HK Trading Import Export e.k. is a family owned German company. Founded in 2004 HK Trading has established itself as a notable trading company. Based on superb and fair business relationships to long-standing
Installation S19-220PT S19-220BPT. Wall-Mounted Eyewash with Plastic Bowl. Wall-Mounted Eyewash with Stainless Steel Bowl.
Wall-Mounted Eyewash with Plastic Bowl Wall-Mounted Eyewash with Stainless Steel Bowl Table of Contents Pre- Information................ Instructions.................... Components and Parts List.......
Hose Clamps & Fittings
All Stainless Steel Marine or Underground Hose Clamps 5/16 HEX HEAD SCREW 60000 SERIES Highly corrosion resistant Use for marine or underground applications Stainless Steel Band, Housing Plated Steel Screw
SRA-125/SRAX-125 Double-Rail Lift-Out Rail System Installation & Service Manual with Parts List
SRA-125/SRAX-125 Double-Rail Lift-Out Rail System Installation & Service Manual with Parts List For MG, WG, WGL, and Grinder Pumps for Effluent & Sewage CAUTION! Read these safety warnings first before
AWWA Butterfly Valve Operation and Maintenance Manual Series 511A & 510A 20 and Smaller
January 2013 AWWA Butterfly Valve Operation and Maintenance Manual Series 511A & 510A 20 and Smaller Milliken Valve Company 190 Brodhead Avenue, Suite 100 Bethlehem, PA 18017 Phone: (610) 861-8803 Fax:
Cleveland Tank & Supply, Inc. School Bus Diesel Fuel Tanks and Accessories. For Immediate Shipment
Cleveland Tank & Supply, Inc. Supplemental Catalog School Bus Diesel Fuel Tanks and Accessories For Immediate Shipment. (216) 771-8265 Fax: (216) 771-8239 www.clevelandtank.com [email protected]
L31125 4/96. Haldex INSTALLATION INSTRUCTIONS HALDEX PURE AIR PLUS EXTENDED PURGE KIT (DQ6027) HEAVY DUTY CANISTER KIT (DQ6028)
L31125 4/96 Haldex INSTALLATION INSTRUCTIONS HALDEX PURE AIR PLUS EXTENDED PURGE KIT (DQ6027) HEAVY DUTY CANISTER KIT (DQ6028) EXTENDED PURGE/HEAVY DUTY CANISTER KIT INSTALL ATION INSTRUCTIONS ' A WARNING
Baumann 87000 Flexsleev Sanitary Control Valve
Product Bulletin D103345X012 Baumann 87000 Flexsleev Sanitary Control Valve The Baumann 87000 control valve (figures 1 and 2) is excellent for throttling high purity liquid or gaseous media commonly found
PRESSURE REDUCING CONTROL VALVE
Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING CONTROL VALVE with LOW FLOW BY-PASS FEATURE Main Line
COLORADO MODEL. 35 x 65 SPECIFICATIONS
COLORADO MODEL 35 x 65 SPECIFICATIONS Dimensions: Roof Dimensions 35-0 x 65-0 Column Dimensions (center to center) 31-0 x 30-6 Minimum Clearance 14-0 Roof Height @ Peak ±18-8 Curved Roof ±42-6 radius Square
WD600 STEAM TRAPS. Thermodynamic Steam Trap
WD600 Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company WD600, WD600L Sizes 3/8, 1/2, 3/4, 1 NPT Material Stainless
PVM Piston Pumps Service Manual
PVM Piston Pumps Service Manual PVM018/020 PVM045/050 PVM057/063 PVM074/081 PVM098/106 PVM131/141 Table of Contents Service Parts Pump Description... 3 Basic pump Pump Operation Controls Types Part Identification...
NORSOK STANDARD COMMON REQUIREMENTS PIPING DETAILS
NORSOK STANDARD COMMON REQUIREMENTS DETAILS L-CR-003 Rev. 1, January 1996 Please note that whilst every effort has been made to ensure the accuracy of the NORSOK standards neither OLF nor TBL or any of
FAIRFIELD INDUSTRIES INC.
FAIRFIELD INDUSTRIES INC. v NEW PRICE SCHEDULE 4/1/201 SUPERSEDES 4/1/11 SPILL CONTAINMENT And STREET ACCESS MANHOLES for UNDERGROUND And ABOVEGROUND TANKS SPILL CONTAINMENT MANHOLES MONITOR WELL SERIES
STANDARD SPECIFICATION SECTION 15257 STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED
STANDARD SPECIFICATION SECTION 15257 STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED PART 1 - GENERAL 1.01 DESCRIPTION This section includes materials, fabrication, installation, and testing of fusion-bonded
167D Series Switching Valves
June 2011 167D Series Switching Valves P1185 P1184 167D TWO-WAY SWITCHING VALVE 167DA THREE-WAY SWITCHING VALVE Figure 1. 167D Series Switching Valves Introduction The 167D Series switching valves are
Product Manual. CVS Type 67AFR Filter Regulator. Introduction. Installation. Description
Product Manual CVS Type 67AFR Filter Regulator Introduction This CVS Controls product manual includes instructions for the installation, adjustment, maintenance and parts ordering of the CVS Type 67AFR
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510
GEET Fuel Processor Plans
GEET Fuel Processor Plans This is a greatly simplified Proof of Concept version of the GEET Fuel Processor that just about anyone can build from parts from a local Hardware store in a weekend for very
DESIGN AND APPLICATION OF HAIRPIN HEAT EXCHANGERS
[email protected] DESIGN AND APPLICATION OF HAIRPIN HEAT EXCHANGERS the Petroleum, Petrochemical, Chemical and Power Industries. Advantages of the Hairpin Heat Exchanger Two Types of Hairpin Heat Exchangers
DOUBLE BLOCK AND BLEED VALVES
DOUBLE BLOCK AND BLEED VALVES ENGINEERING - QUALITY AND TESTING Energy Valves is specialized in designing and manufacturing DBB valves (ball - plug - gate). Technical solutions and engineering are in accordance
Caps STANDARD WEIGHT Inches / Pounds
Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe
Section A SPCC Plan Implementation Checklist This section of the report addresses compliance with certain requirements of Federal Regulations 40 CFR 112. I. STATUS OF SPCC PLAN (40 CFR 112.3) YES NO A.
Automatic Self-Cleaning Strainers
Applications Water and Liquid service Power Industry Cooling water Pulp & Paper Removing fibers Process Equipment Protect equipment Metal & Mining Quenching, blast furnace cooling Automatic Self-Cleaning
SECTION 230529 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 230529 - PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Steel pipe hangers and supports. 2. Metal framing systems. 3. Thermal-hanger shield inserts. 4. Fastener systems.
ATLANTA MODEL SPECIFICATIONS
ATLANTA MODEL 50 SPECIFICATIONS Dimensions: Roof Dimensions (point to point) 50-0 Column Dimensions (out to out of columns) 44-0 Eave Height 8-0 Roof Height @ Peak ±21-8⅞ Hip Roof 6:12 pitch Square Feet
ALTRA 400 Operator Manual. Planographs and Wiring Diagrams
Planographs and Wiring Diagrams 16 Altra 400 Final Assembly All Altras w/head # Part # Description Specific Use (if any) 1 60323A Tank Assy, Altra 400 115 Volt model 60358A Tank Assy, Altra 400 SP 230
Fire Hydrant Troubleshooting
Fire Hydrant Troubleshooting Pulsation or chatter during opening and flow of water from hydrant. Loose condition in stem at lower valve plate nut. Tighten lower valve plate nut and secure with SS lock
SYSTEM PLUMBING KIT INSTALLATION, OPERATION & SERVICE MANUAL. PENTAIR POOL PRODUCTS CORPORATE OFFICE Sanford, NC (919) 566-8000
TANDEM SYSTEM PLUMBING KIT INSTALLATION, OPERATION & SERVICE MANUAL PENTAIR POOL PRODUCTS CORPORATE OFFICE Sanfd, NC (99) 566-8000 PENTAIR POOL PRODUCTS Mopark, CA (805) 53-00 P/N 599 REV. A TANDEM SYSTEM
SIMPLAIR PIPING. www.irtools.com 1-800-376-TOOL
SIMPLAIR PIPING INGERSOLL-RAND SIMPLAIR PIPING With push-in fittings and lightweight anodized aluminum pipe, a SimplAir system provides ideal connection throughout your entire air distribution system.
Accumulators and Receivers
aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Accumulators and Receivers Catalog C-1, October 2007 Page 2 / Catalog
Mustang Series PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE. M115-2 (Globe) M1115-2 (Angle) Schematic. Standard Components
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Throttles to maintain minimum upstream pressure PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE
OVERALL CONVEYOR WIDTH STEEL ALUMINUM MODEL # PER FT. 10 FT. 5 FT. PER FT. 10 FT. 5 FT. PER FT. 10 FT. 5 FT. PER FT. 10 FT. 5 FT.
Pick Smarter. Pick Better. Pick UNEX. Skatewheel (SW) Skatewheel Gravity Conveyor is ideally suited to convey lightweight packages and where operations require portable or temporary conveyor lines such
Baumann 81000 Mikroseal Control Valve
Product Bulletin D103340X012 Baumann 81000 Mikroseal Control Valve The Baumann 81000 Mikroseal control valve (figures 1 and 2) is excellent for throttling of liquid or gaseous media, particularly where
Fisher 1061 Pneumatic Piston Rotary Actuator with Style F & G Mounting Adaptations
Instruction Manual 1061 F & G Actuator Fisher 1061 Pneumatic Piston Rotary Actuator with Style F & G Mounting Adaptations Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...
Proportional Relief Valves
www.swagelok.com Proportional Relief Valves R Series Liquid or gas service Set pressures from 10 to psig (0.7 to 413 bar) 1/4 and 1/2 in. and 6 to 12 mm end connections 2 Proportional Relief Valves Spring
Multipurpose Ball Valves
www.swagelok.com Multipurpose Ball Valves 33 Series Working pressures up to 6000 psig (413 bar) High flow capacity in a compact design Available with PEEK and UHMWPE seats Variety of end connections Low
61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve
61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve Features Rounded polished disc edge gives full concentric sealing, lower torques, longer seat life
3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE
4 3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE A. Changing the Control Board B. Replacing a Heating Element C. Thermistor Replacement D. High Limit Switch Replacement E. Level Detector Replacement
LEAKAGE ACCEPTANCE RATES COMPARISON METAL & SOFT SEATED VALVES API 598/API 6D/MSS SP-61/FCI 70-2
ADELAIDE BRISBANE PERTH LEAKAGE ACCEPTANCE RATES COMPARISON METAL & SOFT SEATED VALVES API 598/API 6D/MSS SP61/FCI TESTING & LEAKAGE RATES OVERVIEW From an engineering point of view, almost all valves
When to use Weldolets... 4,5. Quality Control... 6. How to Order and Specify Branch Connections... 7. Weldolet... 8-14. Standard...
BRANCH CONNECTIONS Table Of Contents When to use Weldolets... 4,5 Quality Control... 6 How to Order and Specify Branch Connections... 7 Weldolet... 8-14 Standard... 8,9 Extra Strong... 10,11 Schedule 160/XX
Hydraulic Jack Units. Contact Us! 888-577-EECO (3326) Delivery & Lead Times
Hydraulic Jack Units Elevator Equipment Corporation (EECO) has been manufacturing hydraulic elevator equipment since 1946, and is one of the leading suppliers in the industry for hydraulic jack units and
Your safety and the safety of others are very important.
NATURAL GAS TO PROPANE CONVERSION KIT 090 INSTALLATION INSTRUCTIONS FOR ALTITUDES 0 -,00 FT. ONLY PROPANE CONVERSION KIT SAFETY... INSTALLATION REQUIREMENTS... Tools and Parts... LP Gas Requirements...
Light Duty Commercial Electric Water Heater
Features Heavy Duty Construction Hydrastone cement lining provides longer tank life Copper-silicon tappings cannot rust or corrode High impact composite jacket eliminates damage during installation and
Fleck 4650. Service Manual INSTALLATION AND START-UP PROCEDURE TABLE OF CONTENTS JOB SPECIFICATION SHEET
Fleck 4650 Service Manual TABLE OF CONTENTS JOB SPECIFICATION SHEET...1 INSTALLATION AND START-UP PROCEDURE...1 CONTROL VALVE DRIVE ASSEMBLY...2 CONTROL DRIVE ASSEMBLY FOR CLOCK...3 BYPASS VALVE ASSEMBLY...4
TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe. 4 Alloy Pipe & Tube. 6 Chrome-Moly Pipe. 7 Low-Temp Pipe
PRODUCT CATALOG TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe 4 Alloy Pipe & Tube 6 Chrome-Moly Pipe 7 Low-Temp Pipe 9 Services amerpipe.com 1.800.316.5737 [email protected] 18333
DeZURIK 3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT
3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT Instruction D10386 August 2013 Instructions These instructions provide installation, operation and maintenance information for BAW Butterfly Valves.
Safety Relief Valve Product Literature & Maintenance Guidelines Revision Jun 2008
Product Literature & Maintenance Guidelines Revision Jun 2008 1.0... Internal Pressure Relief (Safety) Valves...2 75 psi Carbon and Stainless Low-Flow...3 75 psi Carbon High-Flow...4 165 psi Carbon High-Flow...5
6D 23 rd Edition, April 2008 Specification for Pipeline Valves
Handbook API Specification 6D 23 rd Edition, April 2008 National Adoption of ISO 14313 Petroleum and natural gas industries Pipeline transportation systems Pipeline valves API Monogram Required Yes No
20 TANK CONTAINER STANDARD SPECIFICATION MODEL NUMBER: 24 FSTD 2 QUOTATION NUMBER
REVISION: R0 DATE: 04/04/00 20 TANK CONTAINER STANDARD SPECIFICATION MODEL NUMBER: 24 FSTD 2 QUOTATION NUMBER PROPOSED BY: PREPARED FOR: TRENCOR TANK CONTAINERS - 1 - OPERATOR/ OWNER: 1. Technical Characteristics
Scraper Passage Indicator. Electrical Indicator. Features
IV Scraper Passage Indicator Bulletin No: 5110.001.03 Date: June 2008 Cross Indexing No: n/a Supersedes: 5110.001.02 (1/06) Flag Indicator Electrical Indicator Options Description TDW s IV Scraper Passage
60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
Copper and Copper Alloy Tube, Pipe and Fittings
Copper and Copper Alloy Tube, Pipe and Fittings COPPER and COPPER ALLOY TUBE and PIPE Seamless Copper Pipe: Copper pipe is almost pure copper manufactured to the requirements of ASTM B 42 - Standard Specification
Model # 940P-V6. Page 1 of 11
Model # 940P-V6 Page 1 of 11 Page 2 of 11 WARRANTY & TERMS WARRANTY: 5 Year Limited Warranty on Thermoplastic coated elements. Ultra Play guarantees all items for one full year to be free of defects in
2013 Edition. Flanged fittings 30"-64" NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61
30"-64" Ductile Iron industrial Applications, water & Wastewater 2 Table of Contents Flanged Fittings for Water 3 Flange Details 5 Flanged Fittings 6 90º and 45º Bend 6 22-1/2º and 11-1/4º Bends 7 Tees
VALVEWORKS USA OPERATION AND SERVICE MANUAL FOR MODEL FM 2 4-1/16 GATE VALVE
OPERATION AND SERVICE MANUAL FOR MODEL FM 2 4-1/16 GATE VALVE INTRODUCTION In appreciation to our customer for purchasing our product, we have prepared this Operation Manual to assist you in the Operation,
Worcester Controls Three Piece Ball Valves
Worcester Controls Three Piece Ball Valves Series 44, Series 45, Series 59 Experience In Motion Series 44 Ball Valves A quantum advance in ball valve durability, cycle life, leak tightness and automation.