Telecare Solutions Guide. Independence for longer. Telecare Solutions Guide from Chubb Community Care

Transcription

1 Telecare Solutions Guide Independence for longer Telecare Solutions Guide from Chubb Community Care

2 Chubb Community Care technology is designed to promote a fully enabled and integrated telecare service. Our systems can be configured to meet specific customer needs and our products range from standard community alarms, through to sensors for environmental and personal protection, which allow people to live more independently and with greater safety. Our technology offers the choice and flexibility to meet the long-term needs of clients and the requirements and responsibilities of carers. Our Telecare solutions extend to include telehealth monitoring; designed for the management of clients long-term conditions and to complement on-going healthcare regimes. Data such as blood pressure is transmitted confidentially to a response centre or clinician, and any vital signs outside of set parameters will trigger a response. Contents To plan and deliver an enabled care solution that meets every individual need requires an understanding of both the need of the patient and the available technology. Chubb Community Care can provide training and stage local conferences on behalf of local partnerships to develop awareness, advise on technology and identify the possible changes required to deliver an effective response. We will also demonstrate to you the commercial benefits of an advanced telecare service through analysis and business modelling. Every individual has different needs and at Chubb Community Care we are proud to provide comprehensive telecare and telehealth solutions that enable them to lead improved lives independently for longer. In the pages that follow, we detail our product range across Lifestyle Monitoring, Environmental Control, Telecare Sensors and Telehealth all presented with the single aim of allowing users and professional care providers to have solutions that best suit the requirements of each individual circumstance. If you require any further help with the selection of products that meet your needs or would just like friendly and informed advice, please call us on We look forward to hearing from you. Lifestyle Monitoring 3 Environmental Control Solutions 4 Telecare Monitoring 7 IntelliLink Telecare sensors Carer alert Health and Lifestyle Monitoring 15 Telehealth

3 Careful consideration of a client s needs is required to produce a total telecare solution. The table below is a good starting point. A more detailed care plan can be developed by monitoring then assessing a client s behavioural patterns within their own home. Once the results are analysed, an appropriate package can be planned to reduce risk to the client. This could be through the installation of a combination of environmental control systems, telecare solutions or sensors that trigger a call if an emergency occurs resulting in an immediate response to the situation. For long-term care management, Telehealth and Lifestyle systems can be used to closely monitor routine behaviour and, if changes occur, send out alerts that allow more timely intervention to take place. Needs Initial Assessment Solutions Lifestyle Assessment and Monitoring Products QuietCare System Risk Reduction Environmental Controls Possum-SRS Environmental Controls Response and Monitoring Telecare Monitoring IntelliLink Carephone, Telecare Sensors and the Chubb Carer Alert Long Term Monitoring and Management Telehealth and Lifestyle Monitoring Care Companion, Doc@home and the QuietCare System Results lead to Independence, choice and empowerment for the individual. Effective services and significant cost savings for health, housing and social care. For more information call or [email protected]

4 Lifestyle Monitoring QuietCare monitors lifestyle activity and is unique as it predicts normal behavioural patterns and reports significant changes, warning of developing problems and prompting early intervention. It can also be used in conjunction with other procedures as an assessment tool for telecare. Such timely, accurate and actionable information enables Service Clients and their carers to make better decisions relating to their safe, independent and dignified living. It provides peace of mind to carers and helps care professionals make assessments and improve the quality and efficiency of care they provide. As QuietCare is a passive system that requires no behavioural change or intervention on the part of the Service Client it is particularly suited for use with vulnerable and at-risk user groups, such as people prone to falling, or with dementia, diabetes or other chronic conditions. Product QuietCare QuietCare motion sensors The standard QuietCare kit, comprising of five small motion sensors (there is no video or audio) and base unit, is easily installed and simply plugs into the Service Client s telephone and electrical supply. The base unit dials in on a freephone number to the QuietCare central computer every two hours, or more frequently if necessary, and downloads the data. The QuietCare system then analyses the raw motion data and automatically develops a baseline of each Service Clients normal daily activity. Noteworthy changes are identified and reports are generated that can be viewed via a secure internet connection by persons authorised by the Service Client. Alerts can be delivered by , pager or via a call centre. QuietCare Programs QuietCare is the entry service level and is geared towards the individual, self-funded Service Client. The QuietCare service level enables carers to view information for the Service Client via an Individual Summary Screen. Automated alerts are delivered to the Emergency Contacts via or pager. QuietCare Alert offers the same service level as QuietCare with the added benefit that urgent alerts are delivered to Emergency Contacts via a Call Centre. As the name implies, QuietCare Professional is designed for the professional sector, such as Social Services, Housing and PCT s. Carers can view information for each Service Client via the Individual Summary Screen. In addition, the QuietCare Professional Service enables professional carers to case manage a group of Service Clients utilising the QuietCare Group Summary Screen. Automated alerts are delivered to the Emergency Contacts via or pager, or via their own call centre. QuietCare Professional Alert offers the same service level as QuietCare Professional with the added benefit that urgent alerts are delivered to Emergency Contacts via a Call Centre. 03

5 Environmental Control Solutions Environmental Control is a term used to describe the remote operation of household equipment and appliances that feature wireless technology developed primarily for use by the physically disabled and elderly to aid independent living. Typically these include door locks, alarm and intercom, power sockets, lights, curtains, electric bed and chairs, TV, satellite, DVD, stereo, central heating, windows and doors, telephone, warden call system and carephones to name just a few. Integrated with telecare sensor activation, it can also allow remote access to the call centre, automatically switch off lights or turn the water or gas off if these sensors are activated. Doors may also be remotely opened allowing emergency services or care professionals into the home if the user is unable. These solutions give the individual greater control over their home environment and allow the carer to develop a total care package by using the solutions to reduce risk within the home and, in conjunction with a telecare package, enable emergency response if needed. Giving this independence to users helps people to live at home for longer and allows older people and people with a disability to maintain independence, thereby promoting well-being and reducing unnecessary admissions to hospital and residential care. Product Possum-SRS Wireless Wall Switch The Wireless Wall Switch is typically used to switch a lamp on/off (e.g. to light a pathway to the bathroom at night) and to switch mains powered appliances on/off standby using the unisocket. Operating at MHz providing an on/off remote control operation. The Wireless Wall Switch is configured by setting a channel on the two dials beneath the rocker cover with a choice of 256 channels. Dimensions 80x80x150mm WxHxD. Item No. - RS00401 Wireless Wall Switch. Unisocket The Unisocket is a mains plug socket with a radio receiver which when triggered (e.g. from the wireless wall switch or the Wireless Passive Infrared Detector) will switch power on/off to whatever appliance is plugged. The Unisocket has an LED to indicate power on (green) and power off (red). It is configured by setting a channel on the two dials located on the underside of the Unisocket and has a control range of up to 30m. The Unisocket requires no wiring, just plug in and use. Dimensions 60x120x35mm WxHxD. Item No. - RS00101 Unisocket. For more information call or [email protected] 04

6 Product Wireless Passive Infra Red Detector Wireless Voice Alert Motion Detector The Wireless PIR detector detects movement and transmits two radio signals to activate a separate receiver (such as a Unisocket) and effect a response; the first radio signal will switch the Unisocket on and the second will switch it off with the time interval being adjustable at between 4 seconds and 5 minutes. The Wireless PIR detector is connected to a swivel panel to allow adjustment of the The Wireless Voice Alert Motion Detector is designed to detect movement (within an area of 10m by 110 o ) and transmit a radio signal to activate a chime or alarm unit such the Wireless Voice Announcer. Once movement has been detected, the LED on the face of the detector will turn green showing the radio signal (433.9s MHz) has been transmitted. The operating range is up to 30m. area of detection (up to 10m at an angle of detection of 110 o ). Dimensions 120x60x55mm WxHxD. Battery Life Transmission range of 25m and is battery operated (3x AAA alkaline battery 1.5volts). Item No. - RS00901 Wireless Passive IR Detector. Dimensions 60x110x40mm WxHxD. Battery Life Operated by a battery (9V alkaline). Item No Wireless Voice Alert Motion Detector. Wireless Voice Announcer Wireless Magnetic Switch Sensor The Wireless Voice Announcer is a speaker that is operated by radio from the transmitters in the Wireless Voice Alert Detector and Wireless Magnetic Switch Sensor or from the bell push pendant that is supplied with the unit. The Wireless Voice Announcer can be located anywhere in the home or in the work place and can be triggered to sound a pre-recorded voice or music (up to 10 seconds) or it is possible to select from the 8 melodies. The Wireless Magnetic Switch Sensor is designed to work with the Wireless Voice Announcer and is normally adhered to a door or a window. When the door or window is opened the sensor is activated and a radio signal ( MHz) is sent to the Wireless Voice Announcer. Press the bell push pendant and the LED will light up during signal transmission and the Voice Announcer will sound (up to 100m operating distance). Dimensions 90x250x90mm WxHxD. Battery Life Operated by 2x 1.5V alkaline batteries. Item No. - RS04001 Wireless Voice Announcer. Dimensions 60x100x25mm WxHxD. Battery Life Operated by 1x 9V alkaline battery and has a operating range of up to 30m. Item No Wireless Magnetic Switch Sensor. Automatic Response The Automatic Response Link starter pack is designed as an overlay for the IntelliLink carephone to provide an immediate and local automatic environmental control response to sensor activation (e.g. open window in response to CO detector being activated). The Automatic Response Link also makes it possible, (when connected to the IntelliLink), for the call centre to operate the door latch or switch the TV on/ off in response to a call alarm being activated. The starter pack is part of a solution for extra care, environmental protection and dementia care. Item No. - Part number for the Automatic Response is to be confirmed. Please contact us on Home Control Light Solution Gewa 10 starter pack provides a basic environmental control solution where the user can perform up to 32 functions i.e turn a lamp on/off, operate the TV or raise an alarm from a hand held remote controller. The starter pack is part of a solution for extra care and particularly for clients who have impaired mobility but who are able to use a remote control handset. Dimensions 65x120x16mm WxHxD. Weight (inc battery) 150grams. Operating force 150gm. Item No. - Part number for the Home Control Light Solution is to be confirmed. Please contact us on Home Control Medium Solution The Home Control Light starter pack extends the remote control capabilities to provide the user with up to 96 functions and automatic response to sensor activation; a simple input switch is included for users who are unable to press a key on the Possum-SRS Light which also offers voice announcement for those who have visual impairment. The starter pack is part of a solution for extra care and support for people with physical and sensory disabilities. Light Controller Dimensions 120x140x30mm WxHxD. Weight 235grams. Lite Base Station Dimensions 140x75x120mm WxHxD. Weight 510 grams. Speaker output 2watt 8 Ohms. Item No. - Part number for the Home Control Medium Solution is to be confirmed. Please contact us on

7 Product Home Control Touch Solution The Home Control Primo starter pack provides remote control capabilities to provide the user with similar functionality to the Light but with touch screen operation. The Primo controller can also be programmed by the user and carer if required. The starter pack is part of a solution for extra care and support for people with physical and sensory disabilities. Dimensions 190x100x44mm WxHxD. Weight 529grams. Item No. - Part number for the Home Control Touch Solution is to be confirmed. Please contact us on Jelly Bean Switch Auditory and tactile feedback. Flange base for mounting. Available in red, green or blue. Dimensions 20x62mm diameter. Operating force 65gm. Item No. - Black ID00500 Jelly Bean Switch. Cushion Switch Soft switch with cushion bag which can be removed and washed. Velcro tape can be sewn onto the cover for mounting. Internal foam is designed to cushion the impact for users with gross motor problems. Auditory and tactile feedback. Dimensions 40x80mm diameter. Operating force 800gm. Item No. - Red ID02601 Cushion switch, Green ID00602 Cushion switch. Buddy Button Auditory and tactile feedback. Sticker version comes with sticker sheet. All versions come with rubber foam base to prevent slipping. Available in red, yellow, green and blue. Dimensions 20x65mm diameter. Operating force 200gm. Item No. - Black ID00400 Buddy Button. Pillow Switch Smooth foam surface for cheek contact. Secured to pillow or clothing for night time use. Auditory and tactile feedback. Dimensions 20x80mm diameter. Operating force 180gm. Item No. - ID00901 Pillow Switch. For more information call or [email protected] 06

8 Telecare Monitoring IntelliLink The IntelliLink is not just a dispersed alarm, it is also fully telecare enabled. The IntelliLink unit uses the TSA common protocol, BS7369, TT-92 and TT-new protocol to ensure compatibility with any monitoring centre. The unit plugs into a power socket and phone socket, and dials the monitoring centre when any of the telecare devices are triggered. The IntelliLink is not purely a carephone as it accommodates your changing needs in today s health and social care market. It also allows you to specify the level of facilities required and, if your needs or circumstances change, it can be configured to meet them. IntelliLink sets new standards for personal safety and reassurance units, protecting your clients and their property, even when they are not at home. Key Features High clarity hands-free speech for clear and easy voice communication. Up to 22 radio telecare devices can be used with the Executive, 20 on the Classic. Large illuminated alarm button built into the carephone, visible in all lighting conditions and top rated for ease of use by the Research Institute for Consumer Affairs. Person Down alarm facilities. Silent dial alarms for security and domestic violence applications. Multiple emergency numbers allow direct connections through to control centres from ordinary landline telephones or mobile telephones. Up to 8 recordable voice messages, allowing alarm call reasons to be identified to carers receiving alarm calls on their telephone. Supports the portable Verso Pendant Trigger button with multiple wearing options. Supports the portable Verso Fall Detector. Low Battery conditions automatically monitored and reported. Answering and closing down of incoming phone calls using the portable button. Portable buttons can be remotely programmed to the unit by the control centre allowing replacements to be posted to customers when needed. Operates on the dedicated European Alarm frequency 869MHz, helping to ensure that alarm calls always get through. Real time clock (available on the Executive) which allows inactivity monitoring and other time based solutions. Ease of programming using a TV style infra-red remote control, or remotely from the monitoring centre. The IntelliLink is compatible with any control centre using telecare protocols such as TSA common protocol, BS7369 and Tunstall protocols. Dimensions 190x220x55mm WxHxD. Weight 709grams. Battery Back up time 24 hours. The IntelliLink is mains operated. Item No. - FG IntelliLink Classic FG IntelliLink Executive FG Portable infra-red programmer 07

9 Product Verso Portable Button The Verso Portable Button is a light-weight and discreet personal alarm trigger which can be worn on the wrist, around the neck with a wide and comfortable strap or on a belt clip or item of clothing. When pressed, an alarm is raised. Operating on the 869MHz European frequency dedicated to social alarms, it allows emergency calls to be raised even if the button on the carephone is out of reach or in another room. Battery Life 5 years average, depending on usage. The battery is self tested every 48 hours; after 3 consecutive Low Battery states are detected a Low Battery code is transmitted to the control centre. This means that Low Battery reporting does not have to wait for the user to press the button. Range 100m range nominal, depending on building construction and up to 150m line of sight range. Item No. - FG Verso Portable Button. FG Accessory pack for Verso Portable Button including neck strap, clip and wrist strap. Part number for the Dexterity Adaptor is to be confirmed. Please contact us on Verso Fall Detector The Fall Detector can be worn around the neck or attached to the user s belt or clothing notifying a carer or monitoring centre immediately that a user has had a fall. The Fall Detector has an integrated Trigger and Fall Detector meaning that separate devices are not required. A fall condition occurs when the Fall Detector has been in a position of 60 degrees or greater from a vertical. When a fall condition is detected, the IntelliLink sounds a two tone warning. If the Fall Detector is put back in its upright position this warning tone will stop. If the Fall Detector remains in its fall condition for more than a predefined time (which maybe configured to meet the individual needs), the IntelliLink will call the control centre. Battery Life 5 years average, depending on usage. Low Batteries are reported automatically to the control centre, even if the user has not pressed the button. Range 100m range nominal, depending on building construction and up to 150m line of sight range. Item No. - FG Verso Fall Detector. Bogus Caller/ Panic Button Fear of crime can be significantly reduced if the emergency services can be reached at the touch of a button. A Bogus Caller/ Panic Button, installed next to the front door or bed-side, allows the user to raise an alarm if they fear that an intruder or bogus caller is trying to gain access to their property. Alarm calls can be configured to be completely silent if required, which allows the call centre to listen in on the situation and intervene if thought necessary. Dimensions 86x86x38mm WxHxD. Battery Life 5 years average dependent on activations. Low Battery status is self monitored and automatically reported to the control centre. Item No.- FG Bogus Caller/ Panic Button. For more information call or [email protected] 08

10 Product Natural Gas Detector The Natural Gas Detector will raise an immediate alarm when it detects gas. Once the alarm is raised, an optional gas shut-off valve can isolate the supply to the property, ensuring the user is safe while assistance is summoned. The valve is used to shutoff the gas supply when the specified level of natural gas is reached. The valve must be installed by a Corgi Approved engineer. The gas detector must be used in conjunction with the universal transmitter, which provides automatic signalling to the IntelliLink unit. Dimensions 43x154x76mm WxHxD. Battery Life The gas detector is mains operated. Item No. - FG Natural Gas Detector Smoke Detector Heat Detector The majority of people now recognise that it is essential to have a smoke alarm fitted within their home, and the reassurance this provides can now be greatly enhanced with our smoke alarm. When a fire is detected, the unit provides a loud audible warning to the user automatically sending an emergency alarm signal through the IntelliLink. When the signal is received at the call centre, the alarm is recognised as a priority call, and the operator can contact the resident to double check it is not a false alarm if there is no response or the alarm is confirmed, the emergency services can be alerted. The smoke alarm is supplied In certain locations of a property i.e. the kitchen, smoke detectors may give too many false activations. Installing a dedicated heat detector can solve this problem whilst retaining a high level of protection to provide reassurance for the user. Should a fire occur, causing a rapid rise in temperature, the unit will activate once 58 o c is reached raising a local alert. In addition, a call to a carer or monitoring centre can be provided. with a pattress for easy installation, and several smoke alarms can be installed within the property if required. Dimensions Diameter 124mm/ depth 39mm including pattress Battery Life Smoke Detector Alkaline batteries have a service life of 1 to 2 years; Lithium batteries can have a service life in excess of 5 years. Radio Interface 5 years average, depending on usage. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Optical Smoke Detector. Dimensions Diameter 126mm/ depth 35mm plus 17mm for radio module pattress Battery Life Heat Detector Alkaline batteries have a service life of 1 to 2 years; Lithium batteries can have a service life in excess of 5 years. Radio Interface 5 years average, dependent on activations. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Heat Detector. Intruder/Inactivity Monitoring using PIR Detection Inactivity monitor The PIR can look for movement within a defined time. If the user has not moved within that period, due to a fall or feeling unwell, for example, the carephone will send an alarm to the carer/monitoring centre. Intruder monitor If the user leaves their property to stay with friends or visit a day centre, a button on the carephone or the portable button can be used to set the system into away mode. The away mode will detect any intruder, giving peace of mind to the user. Dimensions 65x127x40mm WxHxD plus 32mm for base housing of the radio module Battery Life Alkaline batteries have a service life of 1 to 2 years; Lithium batteries can have a service life in excess of 5 years. Radio Interface This is powered from a lithium cell, which can give up to 5 years service life depending on number of activations. Low battery status is self monitored and automatically reported to the control centre. Item No. - FG PIR Detector. Low Temperature Sensor During the winter months, one of the greatest dangers to the elderly and vulnerable is insufficient heating of their property. If this continues over a period of days, or even hours, hypothermia can set in within a surprisingly short time. A thermostat located within the property allows monitoring of the ambient temperature within the dwelling. If this remains too low over an extended period, an emergency alarm is automatically raised. Time periods are fully programmable allowing the best settings to be achieved for each individual. If the temperature falls below the set level an emergency alarm is automatically raised. Dimensions 88x88x56mm WxHxD. Battery Life 4 years average, dependent upon the temperature settings and activations. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Low Temperature Sensor. 09

11 Product Flood Detector The Flood Detector is installed within the bathroom or kitchen of a property and will alert a user when a sink/basin or bath overflow occurs. It will also detect water on the floor from other sources such as a burst pipe or from a flood from a flat above. This neat, unobtrusive detector will provide an early warning of any potential flood situations which can avoid large repair bills, inconvenience and insurance costs. Dimensions 90x55x28mm WxHxD. Battery Life 5 years average, dependent on activations per day. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Flood Detector. Bed Occupancy Sensor An alarm is raised when a person leaves the bed by a pressure mat under the mattress. This indicates that a user has got out of bed or a chair and is potentially putting themselves at risk. If a user has not returned within a predefined time, the IntelliLink will call the control centre. Item No. - FG Bed Occupancy Sensor. FG Bed Occupancy Sensor with light interface. Dimensions 90x55x28mm WxHxD. Battery Life 5 years average, dependent on activations per day. Low Battery status is self monitored and automatically reported to the control centre. Carbon Monoxide Detector When gas appliances become faulty or have not been serviced correctly, a dangerous build-up of carbon monoxide can occur. As this toxic gas is colourless and odourless, it is essential that early detection is achieved. Installing carbon monoxide detectors adjacent to the appliances in question - for example, the central heating boiler or a gas fire, will ensure an emergency alarm call is raised when the gas build-up reaches a concentration which is hazardous to health. As with natural gas detection, an automatic gas shut-off valve can also be fitted if required. Dimensions 79x145x50mm WxHxD. Battery Life The Carbon Monoxide detector is battery powered and will give a 6 year and 3 months service life (manufacturer s specification). Radio Interface 5 years average, depending on activations per day. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Carbon Monoxide Detector. For more information call or [email protected] 10

12 Product Pull Cord In extra care situations it may be preferable to have fixed emergency call points in certain rooms of the home. Pull Cords can be ceiling mounted in convenient locations allowing the user to raise an alarm if their pendant trigger is not accessible. The alarm is raised by simply pulling down on the distinctive orange cord, which incorporates two triangular handles to provide ease of grip. Dimensions Diameter 70mm/depth 84mm Battery Life 5 years average, dependent on activations. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Pull Cord. Pill Dispenser A fully automatic Pill Dispenser takes the worry out of dispensing medication to older or vulnerable people. At pre-programmed times the Pill Dispenser carousel rotates to allow the user to take the appropriate medication. An intermittent audible alert tone is provided as a medication reminder. The unit knows when the pill has been removed from the dispenser, so if the medication has not been taken after a preset time, a radio link to the carephone will automatically call the control centre. The unit only dispenses the dosage due at that time reducing the risk of double dosing. Dimensions Diameter 180mm, depth 47mm. Battery Life 6 months, there is a visual indication of Low Battery on the Pill Dispenser. Item No. - FG Pill Dispenser with Radio Link. CS12174 Tray with lid, 3 timer disks and instruction booklet Bed Occupancy Sensor with Light The Bed Occupancy Sensor with light, will detect when a user has left the bed and not returned within a preset time. It can also be configured to alert carers or the control centre, if the person has not got into or out of bed by a certain time. When leaving the bed during the night, the bed-side light will be switched on, lighting their way and reducing the risk of a fall. A timer can also be set to ensure the sensor will work only during night time hours. The user can switch the light on or off from within the bed with a remote switch, further reducing the risk of falling out of bed. Dimensions 650x95x20mm WxHxD. Battery Life The Bed Occupancy sensor with light is mains operated. Item No. - FG Bed Occupancy Sensor with light, timer and panic alarm. Enuresis Sensor Provides an early warning for individuals prone to incontinence whilst sleeping. A sensor pad placed between the bedding and mattress allows detection of excess amounts of moisture. If this occurs, an emergency alarm call can be transmitted. The bed sensor is designed to be easily cleaned, dried and replaced and is attached to a control unit by a very slim wire which is designed to not disturb the user while in bed. Dimensions Control Unit 80x40x20mm Bed Mat 600x400mm. Battery Life 5 years average dependent on activations. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Enuresis Sensor. 11 Door Contacts The security and safety of vulnerable users can be guaranteed discreetly and remotely by ensuring they remain within their property at certain times of the day or night. Using magnetic contact devices, the opening of doors and windows can be automatically monitored. This allows the call centre to raise the alarm if a person leaves the house at an unusual time. Time periods are fully programmable allowing the best settings to be achieved for each individual. Door Contacts can also monitor intruders and can be set in an away mode which will send an alarm to the control centre if access is detected while the user is out of the house, for example. Dimensions Control Unit 40x80x20mm WxHxD. Battery Life Average 4 years, depending on activations per day. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Door Contacts. FG Door Contacts (including key switch).

13 Product Care Sensor The Chubb Care Sensor provides a unique non-intrusive, non-bodily worn solution to provide security for older and disabled people where staff members are present on site to activate and deactivate when required. The Care Sensor alarms if a person does not get back into bed within a predefined time period; measures the time it takes to get out of bed, the time it takes to walk from the bed to a designated point, counts the number of times the bed is left during the night and detects people entering the room when it is armed. The Care Sensor is mounted on a wall over the bed, configured using an infrared remote control and linked to the carephone to trigger alarms. It allows bed exit monitoring without having pads or sensors physically in contact with the bed, giving an exceptional product lifetime with low maintenance. Dimensions 166x68x77mm WxHxD (including mounting bracket). Weight 290gram (including mounting bracket & cable). Battery Life Remote control 1 year with normal use. The Care Sensor is mains operated. Item No. - FG Care Sensor Natural Gas/Carbon Monoxide (CO) Detector This solution detects both natural gas and carbon monoxide. An immediate alarm will be raised if it detects a specified level of gas. Once the alarm is raised, an optional piece of equipment can shut-off the supply to the property, ensuring the user is safe while assistance is summoned. The valve is used to shut off the gas supply when the specified level of natural gas is reached. The valve must be installed by a Corgi Approved engineer. The gas detector can be stand alone or an automated system, it is BSI approved. Dimensions 100x145x55mm WxHxD. Battery Life The gas detector is mains operated and is recommended to be installed by a qualified electrician. Item No. - FG Natural Gas/ Carbon Monoxide (CO) Detector For Gas Shut Off Valve and Valve Actuator Control Unit, contact us. Please contact us on Epilepsy Sensor The Epilepsy Sensor will raise an alarm to a monitoring centre or other alarm recipient when a seizure is detected. The sensor is designed to detect Tonic- Clonic (Grand Mal) seizure types only. That is, during the seizure there must be convulsions (shaking or jerking movements). Any other seizure types such as partial or absence seizures without movement would not be detected. The detector is equipped with a movement sensor that is positioned between the bed base and mattress. The sensor has an adjustable level control with a movement detect confirmation LED. A further control, delay, is used to minimise false alarms caused by normal movements during sleep. Using these controls it is possible to fine-tune operation of the monitor to suit most bed types and convulsive seizure types. A built in microphone can be used to detect grunting or groaning sounds that sometimes precede a seizure from adult males. Again, an adjustable sensitivity control allows the correct level to be set. Dimensions Monitor 150x105x45mm, Sensor 75x55x25mm. Battery Life 12 hours full battery backup. Power 12V DC Power adaptor. Sensor lead 2 Meters. Item No. - FG Epilepsy Sensor Universal Transmitter Universal Transmitters can be used to link many types of additional sensors or items of auxiliary equipment via radio, to the carephone which forwards a call to the control centre. All that is required is a suitable volt free contact, which will close on alarm. Dimensions 40x80x20mm WxHxD. Battery Life 5 years average, dependent on activations. Low Battery status is self monitored and automatically reported to the control centre. Item No. - FG Universal Transmitter with Test Button, FG Universal Transmitter without Test Button For more information call or [email protected] 12

14 Carer Alert Telecare technology from Chubb Community Care has traditionally provided support to those living independently via a carephone to a community alarm centre. However in some cases there may be a need for an on site carer to be notified immediately that an incident occurs within the home. This system can either work in isolation or with a default setting through to a IntelliLink carephone. This allows the carer to leave home safe in the knowledge that the alarm will notify them either on their mobile telephone or the Community Alarm Centre. The Carer Alert is used to indicate alarms from portable and stationary telecare solutions. The device has 8 indicator lights for which up to 8 telecare devices may be assigned. Along with the lights, there is a buzzer to alert the carer as soon as the alarm is activated. The box itself can also be semi-portable when used as a stand alone system so it can be plugged into the nearest power socket to the carer. Many formal and informal carers live on site with the people they look after. Carer Alert provides peace of mind to carers, allowing them to live an independent life and can help manage the risk of having the person they are caring for living at home. Key Features Flexible and cost effective way of providing a call system in a local care environment. Supports carers in their caring role. 8 indicator lights support up to 8 telecare devices. Supports the Verso portable button and range of telecare sensors. Buzzer sound to alert the carer as soon as alarm is activated. Can work in isolation or with a default setting to the IntelliLink carephone. Option for box to be semi-portable when used as a stand alone system and can be plugged into the nearest power socket to the carer. When an alarm is activated the appropriate telecare sensor will light up on the box to inform the carer where the incident is occurring. Can support all telecare sensors in a property even if they are not programmed to the carer alert. When an alert is sent in this mode only the top LED will light up. Gives an alarm if any of the batteries in the programmed telecare sensors are becoming weak. Dimensions 82x143x30mm WxHxD. Battery Life The Carer Alert is mains operated. Item No. - FG Verso Carer Alert 869MHz with buzzer. 13

15 Telecare meets the needs of an individual s circumstance and therefore each package can be individually tailored. In order to help you select the right solutions for the right need, Chubb Community Care have developed and can recommend a basic package guide which can then be tailored to suit a user s needs. IntelliLink Carer Alert Verso Portable Button Dexterity Adaptor Fall Detector Bogus Caller Button Pull Cord Pill Dispenser Bed Occupancy Sensor Bed Light Sensor Flood Detector Enuresis Sensor Care Sensor Door Contacts Intruder Alert Inactivity Alert Smoke Detector Heat Detector Natural Gas CO Detector Low Temperature Detector Epilepsy Sensor Bogus Caller Intruder Safety Dementia Falls Managemant Epilepsy Domestic Violence Environmental Safety Vulnerable Hearing Impairment Visual Impairment Personal Safety Delayed Discharge Racial Harassment Extra Care Wandering Alert For more information call or [email protected] 14

16 Health and Lifestyle Telecare also includes telehealth, designed for the management of clients long-term conditions and to complement on-going healthcare regimes. Data such as blood pressure is transmitted confidentially to a response centre or clinician, and any vital signs outside of set parameters will trigger a response. For people with medical conditions that require regular care and monitoring, Telehealth means the difference between spending time in hospital and living independently and comfortably at home. Telehealth systems will ensure that they still receive the protection and reassurance they need including being reminded about medication to clinical consultations via an automated question and answer system, videophone or direct speech. For hospitals and other healthcare providers it means freed-up beds, fewer unscheduled visits to A&E units, G.P s surgeries or clinics and more efficient use of both hospital-based and home-visiting nursing staff. The Chubb Community Care telehealth systems can also be used by public service providers such as Social Services for everything from care in the community to occupational therapy, which results with savings in valuable time, resources and cost. Product Care Companion Level 1: The basic Care Companion is a self-contained home unit perfectly suited for a person or patient requiring assessment and reminders. It is designed for patient ease of use and features large text and a touch-screen. The Care Companion prompts the person or patient to take medications and answer easily programmed questions related to their specific health needs. Data collected by the Care Companion is sent to a Care Companion Server every day via the patient s home telephone line to a web based server. Information is accessed by health professionals via a web interface, designed to support health management by providing medical data, daily answers to prompted questions (such as how do you feel compared to yesterday? ), data trends and alerts at set parameters. Care Companion with Wireless Medical Devices Level 2: Medical peripherals are added to the basic Care Companion to meet the patient s specific health needs. The Care Companion collects the data then sends it to the Care Companion Server. If the server receives data that exceeds pre-set parameters, the assigned caregivers are notified. Caregivers can access their patients medical data via a secure web browser. The data can be reported and graphed to meet the caregiver s needs. 15

17 Product Care Companion Software The web based software is used by the clinician to view patient information. When a clinician enters the software a list of patients treated by incoming health professional is displayed, these are sorted by alarm/warning status. Each patient record contains basic patient information including medical history, medication, allergies etc. It also contains a summary of clinical protocol responses and summaries of vital sign statistics, graphs and reports. Each record can be personalised for each alarm/warning thresholds. Once an alarm/warning occurs the software will alert the clinician. Weight Scale The Weight Scale is used to effectively monitor patient weight. This device is used to manage weight gain which affects diseases such as diabetes and CHF Large easy to read display Simple one button control Accurate to 0.1lb (50g) Sleek stylish unit Wireless and wired options available Item No. - AMD-9925 Weight Scales. Blood Pressure The Blood Pressure device is used to effectively monitor blood pressure and pulse rate. This device is used to manage a wide variety of diseases. Professional accuracy via oscillometric method Automatic inflation Different cuff sizes available BHS approved Item No. - AMD-9930 Blood Pressure. Pulse Oximeter The Pulse Oximeter is used to effectively monitor daily blood oxygen levels. This device is used to manage such diseases as COPD, chronic asthma and CHF. Non invasive Accurate, durable Simple automatic operation Wireless Item No. - AMD-9915 Pulse Oximeter. Peak Flow Meter The Peak Flow Meter is used to effectively monitor lung function and respiratory output. This device is used to manage diseases such as COPD and chronic asthma. Ease of use Measures PEF, FEV1, FEV6, FEV1/FEV6 Single button Washable mouthpiece Easy to read LCD screen with graphic animation Wireless Item No. - AMD-9905 Peak Flow Meter. For more information call or [email protected] 16

18 Product Care Companion with Wireless Medical Devices Level 3: Add any video speakerphone to the Care Companion and the patient can receive more personal interaction with, and immediate assistance from, a care giver. This visual reassurance link is vital for family members, support groups and professional carers. The videophone can operate over POTS, IP or ISDN. Video Phone Videophone communication improves the reach and effectiveness of care provider services and gives patients greater access to medical practitioners, social care providers and the family support network. Remote video calls promote more frequent interaction between patient and care giver, fostering better regimen compliance. It also allows care practitioners to call on more patients per day, while continuing to provide conscientious, quality healthcare to each. By extending provider resources and fostering patient s health maintenance and self management of their illness, video telehealth helps lower the overall cost of health and social care, whilst maintaining the independence of the client. Nurse Station Software The web based software is used by the clinician to view patient information. When a clinician enters the software a list of patients treated by being monitored by the health professional is displayed, these are sorted by alarm/warning status. Each patient record contains basic patient information including medical history, medication, allergies etc. It also contains a summary of clinical protocol responses and summaries of vital sign statistics, graphs and reports. Each record can be personalised for each alarm/warning thresholds. Once an alarm/warning occurs the software will alert the clinician. 17

19 The remote health management service for home-based patients suffering from Chronic Heart Failure (CHF), employs telecare technology to acquire on a daily basis, key physiological, lifestyle and medication compliance parameters. The acquired parameters are collected using a fit-for-purpose, hand-held terminal, which has been designed with use by a wide population of patients in mind, employing large buttons and a big clear display to aid usability, and predominately using simple graphical symbols for patient interaction. The handheld unit can collect ECG and Bio- Impedance measurements using built-in sensors, as well as a wide range of other physiological parameters from third party sensors and devices. The collected parameters are automatically transferred to a central, secure database using an 0800 telephone number, thereby incurring no cost to the patient. Furthermore, the terminal employs rechargeable batteries and is suitable for the patient to use while temporarily away from home - for example if travelling. From the central, secure database, this data is made available to the healthcare professionals responsible for the patient s care via a secure web site. Normally this is accessed at scheduled consultation times or in the case of an unexpected development in the patient s condition. The acquired information is also fedback to the patient in an easy to digest graphical report showing trends in their blood pressure and the corresponding trends in their lifestyle parameters and medication compliance. The aim of these reports is to help the patient understand how changes in their lifestyle and medication affect their condition so providing a tool for them to autonomously manage their disease. Weekly reports showing the trends for the preceding 4 weeks are delivered to the patient s terminal, while more detailed paper reports are delivered via post each month. Doc@Home Software Care providers are able to review the information recorded by the patient at any time using the Doc@Home secure web connection. The short, medium and long term trends of health status and peak flow can be immediately assessed and interpreted in the light of lifestyle, medication and compliance. Authorised users can define the criteria for Alerts and customise the questions asked of the patient each day. Events leading up to exacerbations can be reviewed and appropriate advice given to the patient. All of the information is readily available should the patient make telephone contact with the care provider in order to report a concern over any recent development or health change. For more information call or [email protected] 18

20 Chubb Community Care A UTC Fire & Security Company Registered Office: Shadsworth Road, Blackburn, BB1 2PR Registered in England No t: f: w: We reserve the right to update product specifications in line with our policy of continual development. September 2007 version 1