ZUP SERIES. Model naming method. Features. Applications. Conformity to RoHS Directive. Product Line up ZUP Programmable CVCC 200W 800W 19Model

Transcription

1 SERIES Programmabe CVCC 200W 800W 19Mode Features 800W Constant Votage/Constant Current uit-in RS232 & RS485 Interface An embedded Microprocessor controer Digita Encoder Knob Software Caibration Last Setting Memory Parae Operation (Master/Save) Active Current Sharing Externa Votage or Resistance Programming Votage up to 120V, Current up to 132A Active Power Factor Correction: 99% Vac Universa Input Votage 19" Rack Mounted ATE and OEM Wordwide Safety Agency Approvas CE Mark for LVD and EMC Reguation Product Line up 200W, 400W Mode naming method / Series name Output Votage Output Current ( 0 36V ) ( 0 12A ) Front Pane L. Output Jacks LANK: Standard Appications 3 Seria Link Cabe W. Cabe incuded LANK: None AC Cabe E. Europe U. USA O. Unterminated I: SI 32 std. LANK: None Conformity to RoHS Directive This means that, in conformity with EU Directive 2002/95/ EC, ead, cadmium, mercury, hexavaent chromium, and specific bromine-based fame retardants, P and PDE, have not been used, except for exempted appications. 200W 400W 800W Output Votage Output Current Mode Output Current Mode Output Current Mode 0-6V 0-33A A A V 0-20A A A V 0-10A A A V 0-6A A A V 0-3.5A A A V 0-2.5A A 80-5 ー ー 0-120V 0-1.8A A ー ー A-341

2 SERIES Specifications ITEMS/UNITS MODEL OUTPUT VOLTAGE (*1) V OUTPUT CURRENT (*2) A RATED OUTPUT POWER W LOAD REGULATION 0.005%+2mV From No oad to Fu oad, constant input votage. LINE REGULATION 0.005%+1mV From VAC or VAC, constant oad. CONSTANT VOLTAGE CONSTANT CURRENT PROGRAM MING (*9) RMS RIPPLE (5Hz-1MHz andwidth) mv RIPPLE (pk to pk) (20MHz andwidth) mv RECOVERY TIME (*3) ms TEMPERATURE COEFFICIENT 30ppm/ C from rated votage foowing 30-minute warm-up. TEMPERATURE DRIFT 0.01%+2mV Change in output over 8-hour interva under constant ine, oad and ambient temp foowing30-minute warm-up. UP PROGRAMMING RESPONSE TIME (*4) ms DOWN PROGRAMMING FULL LOAD ms RESPONSE TIME NO LOAD ms LOAD REGULATION (*5) 0.01%+5mA 0.01%+5mA 0.07%+10mA 0.01%+5mA 0.01%+5mA 0.07%+10mA 0.01%+5mA LINE REGULATION (*6) 0.01%+2mA 0.01%+2mA 0.01%+5mA 0.01%+2mA 0.01%+2mA 0.01%+5mA 0.01%+2mA RMS RIPPLE (5Hz-1MHz andwidth) ma TEMPERATURE COEFICIENT 100ppm/ C from rated current foowing 30-minute warm-up. TEMPERATURE DRIFT (*8) 0.02%+5mA 0.02%+5mA 0.05%+10mA 0.02%+5mA 0.02%+5mA 0.05%+10mA 0.02%+5mA RESOLUTION etter than 0.028% of rated output votage VOLTAGE ACCURACY 0.02%+5mV 0.02%+8mV RESOLUTION etter than 0.03% of rated output current CURRENT ACCURACY 0.4%+40mA OVERVOLTAGE PROTECTION (*10) V HOLD-UP TIME 20mS At 100V/200VAC, rated output votage and output current. VOLTAGE 3 digits ( 6v; 20v; 36v; 60v; 80v); 3.5 digits ( 10v; 120v ) accuracy: 0.2% +/- 2 digits. DISPLAY CURRENT 3.5 digits (132A); A others 3 digits, accuracy: 0.5% +/- 3 digits. STATUS CV/CC, Aarm, Fod, Loca/Remote, On/Off. OUTPUT PROTECTIONS Over Votage, Over Temperature, Fodback. INPUT VOLTAGE (*11) Vac Continuous, 47-63Hz INPUT CURRENT (*12) A 3.0/ / / / / / /1.4 INPUT INRUSH CURRENT ( 100/200V ) A 15/30 (*7) /30 (*7) /30 (*7) EFFICIENCY ( *12 ) % 69/72 74/77 74/77 73/77 79/82 77/81 74/78 INPUT CURRENT HARMONICS Compies with EN , Cass A POWER FACTOR (TYP) 0.99 at 100/200Vac, 100% oad. OPERATING TEMPERATURE 0 to 50 C ; 100% Load. OPERATING HUMIDITY 30-90% RH ( No dewdrop ). ENVIRONMENT STORAGE TEMPERATURE -20 to 70 C STORAGE HUMIDITY 10-95% RH (No dewdrop). VIRATION 10-55Hz, Ampitude (sweep 1 min ) 2G, X, Y, Z, When mounted with mounting screws. SHOCK Less than 20G MECHANICAL WEIGHT Kg SIZE (W x H x D) mm 200W and 400W units: 70 x 124 x W units: 140 x 124 x 350 (Refer to outine drawing) OUTPUT ON/OFF y TTL Signa or Dry Contact (Refer to instruction manua). OUTPUT GOOD EXTERNAL OUTPUT VOLTAGE PROGRAMMING CONTROL OUTPUT CURRENT PROGRAMMING FUNCTIONS REMOTE SENSING COMMUNICATION INTERFACE SAFETY STANDARDS APPROVALS EMC STANDARDS CONDUCTED EMI RADIATED EMI SERIES OPERATION PARALLEL OPERATION COOLING WITHSTAND VOLTAGE ISOLATION RESISTANCE Open coector (Refer to instruction manua). y Votage ( 0-4V ) or by Resistance ( 0-4K ) (Refer to instruction manua). y Votage ( 0-4V ) or by Resistance ( 0-4K ) (Refer to instruction manua). Maximum 0.5V drop on each oad wire for mode up to 60V and 2V for the 80V, 120V modes RS232 and RS485 uit-in, IEEE488 Optiona. UL3111-1, EN EN , IEC , FCC part 15 (cass A). EN55022-, FCC-, VCCI-2 EN55022-A, FCC-A, VCCI-1 Up to 2 units (Refer to instruction manua). Master - Save method; up to 5 units (Refer to instruction manua). Forced air by bower fan (ower fan is mounted within unit). Input - Chassis...2.0kVAC 1 min, Input - Output...3.0kVac 1 min, Output - GND...500VAC 1 min. More than 100MOhm at 25 C and 70% R.H. (*1) Minimum votage is guaranteed to maximum 0.2% of the rated output votage. (*2) Minimum current is guaranteed to maximum 0.4% of the rated output current. (*3) Time for recovery to within +/-50mV against current change of 50% to 100%. (*4) From zero vots to fu scae, resistive oad and current setting at maximum. (*5) From no oad to fu oad, constant input votage. (Measure with JEITA RC-9131 probe.) (*6) From 85~132Vac or 170~265Vac constant oad. (*7) At cod start Ta=25 C. (*8) Change in output over 8 hour interva constant ine, oad and ambient temperature foowing 30-minutes warm-up. (*9) Given for contro of the output via the seria communication or via front pane contros. (*10) Inverter shut down method, manua reset (OVP wi shut down output) (*11) For cases where conformance to various safety specs. (UL, IEC, etc.) are required, to be described as VAC (50/60Hz) on name pate. (*12) At 100V/200V and Maximum Output Power. - When forced air cooing, refer to derating curve. A-342

3 SERIES %+4mV 0.005%+2mV %+5mA 0.07%+10mA 0.01%+5mA 0.01%+5mA 0.07%+10mA 0.01%+5mA 0.01%+5mA 0.07%+10mA 0.01%+5mA 0.01%+5mA 0.01%+5mA 0.01%+5mA 0.01%+2mA 0.01%+5mA 0.01%+2mA 0.01%+2mA 0.01%+5mA 0.01%+2mA 0.01%+2mA 0.01%+5mA 0.01%+2mA 0.01%+2mA 0.01%+2mA 0.01%+2mA %+5mA 0.05%+10mA 0.02%+5mA 0.02%+5mA 0.05%+10mA 0.02%+5mA 0.02%+5mA 0.05%+10mA 0.02%+5mA 0.02%+5mA 0.02%+5mA 0.02%+5mA 0.02%+12mV 0.02%+20mV 0.02%+35mV 0.02%+50mV 0.02%+80mV / / / / / / / / / / / / /30 (*7) /30 (*7) /30 (*7) 15 15/30 (*7) 15 79/83 79/82 76/80 80/84 80/84 75/79 80/84 80/84 78/82 83/87 78/82 82/ A-343

4 ADDR OVP/UVP V/A FOLD REM OUT ADDR OVP/UVP V/A FOLD REM ADDR OVP/UVP OUT V/A FOLD REM OUT ADDR OVP/UVP V/A FOLD REM OUT SERIES Outine Drawing [ 200W/400W Units] unit: mm 70x124x350 WEIGHT: Kg 200W units: W units: Note: 1: Housing AMP: with pins AMP: : Header PHOENIX: PSC 1,5/3-M-PE Pug PHOENIX: PSC 1,5/3-3-F Pastic cabe housing Incuded with the power suppy ± ± ± ±0.5 ± 0.5 ± ± Mounting Mounting Hoes Hoes Tap M4 x 4 Tap marked M4 x 4 Amarked A 13.0 Note 1 Externa Note 1 Note Contro 1 Externa Externa Connector Contro Contro Connector Connector ± ± ± 1.0 ± RS232/RS485 communication RS232/RS485 RS232/RS485 connectors 20.0 RS232/RS485 communication communication connectors communication connectors connectors ± Mounting Hoes Tap Tap M4 x 4 marked AA Rubber Rubber umpers umpers 4 paces 4 paces marked marked (removabe) (removabe) Rubber umpers Rubber umpers 4 paces marked 4 paces marked (removabe) (removabe) Note 1 Externa Contro Connector 19.0 Rear Pane Output Votage Connector For 80V, 120V Modes [ 800W Unit] ± 0.5 REMOVALE HANDLE REMOVALE HANDLE REMOVALE REMOVALE HANDLE HANDLE Note 1 Externa Contro Connector Note Externa Note 1 Note Contro 1 Externa Externa Connector Contro Contro 47.0 Connector Connector ± ± ± 0.5 unit: 140x124x350 mm POWER 99.6± ± 0.5 ± 0.5 POWER ± ± ± 1.0 ± ± 1.0 ± 1.0 RS232/RS485 communication connectors ± 1 WEIGHT: 5.8 kg POWER 99.6± ± 1 POWER Note: 1: Housing AMP: with pins AMP: Incuded with the power suppy. RS232/RS485 communication RS232/RS485 RS232/RS485 connectors communication communication connectors connectors Rubber umpers: 4 paces marked (removabe) Mounting Hoes: Tap M4 x 4 marked A A-344 Rubber umpers: 4 paces marked (removabe) Rubber umpers: Rubber umpers: 4 paces marked 4 paces marked (removabe) (removabe) Mounting Hoes: Tap M4 x 4 marked A Mounting Mounting Hoes: Tap Hoes: M4 x 4 Tap marked M4 x 4 Amarked A

5 SERIES Accessories Accessories / optiona items (refer to the attached diagram for appearance) 1. AC Cord Sets Three optiona cords are possibe according to order: Region AC Cord Power Suppy Connector Wa Pug P/N / J Europe 10A / 250Vac L =2m -C13 INT L 7 / VII / E / O North America Europe S-32 Standard 2. Communication Cabe RS232/RS485 cabe is used to connect the power suppy to the PC controer Mode PC connector Communication cabe Power Suppy Connector P/N RS232 D-9 Shied Ground, L=1m EIA / TIA-568A (RJ-45) /NC401 RS232 D-25 Shied Ground, L=1m EIA / TIA-568A (RJ-45) /NC403 D-25 (femae connector) D-9 (femae connector) EIA/TIA (RJ-45) 3. seria ink cabe Used to chain Power Suppy to Power Suppy from a seria communication bus Mode Communication cabe Power Suppy Connector Remote IN / OUT P/N RS485 Shied Ground, L = 50cm EIA / TIA-568A (RJ-45) / W A-345

6 SERIES Options ( 200W, 400W, 800W Modes ) 1. FRONT PANEL OUTPUT JACKS P/N: / L Outine Drawing: Physica Dimensions in mm. 200W/400W Units: 70x153x W Units: 140x153x405.9 Up to 20A output current via front pane jacks. 2. ASSEMLIES Dua Output Packing 200W/400W modes P/N: /NL " RACK MOUNTED ATE AND OEM UP TO 2.4 KW Up to six power units can be assembed into a 19, 3U rack, kit P/N NL100. In cases where the entire rack is not occupied with power units, NL101 bank panes can be instaed. P/N: /NL100 A-346

7 SERIES Appication exampes Configurations ENCH TOP POWER SUPPLY Singe Parae (Master / Save) PARALLEL OPERATION Master - Save method: Active current sharing up to 5 units. REMOTE PROGRAMMING VIA RS232 Up to 31 units can be controed via RS232 interface. Linking units with RS232 contro. REMOTE PROGRAMMING VIA RS485 Up to 31 units can be controed via RS485interface. For operation environments that require high noise immunity or ong distance communication, it is recommended to use the buit- in RS485interface. Linking units with RS485 contro. Remote Programming Via GPI. GPIDRS485 CONTROLLER The GP485 is a high performance seria to GPI Interface It enabes a series with RS485 port to be a Taker, Listener, or controer on the GPI * Contros up to 31 units through a singe GPI address. * Conforms to a versions of the IEEE488 standard, incuding IEEE * 19 racking possibiity. * Appication software - LabView, LabWindows. A-347

8 SERIES Rack Mounted ATE and OEM up to 2.4KW Six units can be assembed into 19-inch rack / 3U high to meet your configuration requirements Power Modues Tabe Modue Type 200W 400W 800W 0 ~ 6V 33A 66A 132A 0 ~ 10V 20A 40A 80A 0 ~ 20V 10A 20A 40A 0 ~ 36V 6A 12A 24A 0 ~ 60V 3.5A 7A 14A 0 ~ 80V 2.5A 5A 0 ~ 120V 1.8A 3.6A 19"rack width 1 / 6 width 1 / 6 width 2 / 6 width A-348