SOT23, Low-Power µp Supervisory Circuits with Battery Backup

Size: px
Start display at page:

Download "SOT23, Low-Power µp Supervisory Circuits with Battery Backup"

Transcription

1 ; Rev 4; 1/11 SOT3, Low-Power µp Supervisory Circuits General Description The supervisory circuits reduce the complexity and number of components required for power-supply monitoring and battery control functions in microprocessor (µp) systems. The circuits significantly improve system reliability and accuracy compared to that obtainable with separate ICs or discrete components. Their functions include µp reset, backup battery switchover, and power failure warning. The operate from supply voltages as low as +1.. The factory-preset reset threshold voltage ranges from.3 to 4.63 (see Ordering Information). These devices provide a manual reset input (MAX6361), watchdog timer input (MAX636), battery-on output (MAX6363), and an auxiliary adjustable reset input (MAX6364). In addition, each part type is offered in three reset output versions: an active-low open-drain reset, an active-low open-drain reset, and an active-high opendrain reset (see Selector Guide at end of data sheet). Computers Controllers Intelligent Instruments Critical µp/µc Power Monitoring TOP IEW, MR Applications Pin Configurations 1 6 BATT MAX SOT3-6 Fax Machines Industrial Control POS Equipment Portable/Battery-Powered Equipment 5 OUT CC Pin Configurations continued at end of data sheet. Selector Guide appears at end of data sheet. Typical Operating Circuit appears at end of data sheet. Features Low +1. Operating Supply oltage ( CC or BATT ) Precision Monitoring of +5., +3.3, +3., and +.5 Power-Supply oltages Debounced Manual Reset Input (MAX6361) Watchdog Timer with 1.6s Timeout Period (MAX636) Battery-On Output Indicator (MAX6363) Auxiliary User-Adjustable IN (MAX6364) Three Available Output Structures Push-Pull, Open-Drain, Open-Drain / alid Down to 1. Guaranteed ( CC or BATT ) Power-Supply Transient Immunity 15ms (min) Reset Timeout Period Small 6-Pin SOT3 Package MAX6361LUT -T MAX6361PUT -T MAX6361HUT -T MAX636LUT -T MAX636PUT -T MAX636HUT -T MAX6363LUT -T MAX6363PUT -T MAX6363HUT -T MAX6364LUT -T MAX6364PUT -T MAX6364HUT -T Ordering Information TEMP RANGE PIN-PACKAGE Note: These parts offer a choice of reset threshold voltages. From the table below, select the suffix corresponding to the desired threshold voltage and insert it into the part number to complete it. When ordering from the factory, there is a 5- piece minimum on the SOT package (tape-and-reel only). Devices are available in both leaded and lead-free packaging. Specify lead-free by replacing "-T" with "+T" when ordering. SUFFIX MIN TYP THRESHOLD RANGES () MAX Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim Direct at , or visit Maxim s website at

2 ABSOLUTE MAXIMUM RATINGS Terminal oltages (with respect to ) CC, BATT, OUT to +6 (open drain), (open drain) to +6 BATT ON, (push-pull), IN, WDI to ( OUT +.3) MR to ( CC +.3) Input Current CC Peak...1A CC Continuous...5mA BATT Peak...5mA BATT Continuous...4mA...75mA Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS Output Current OUT...Short-Circuit Protection for up to 1s,, BATT ON...mA Continuous Power Dissipation (T A = +7 C) 6-Pin SOT3 (derate 8.7mW/ C above +7 C)...696mW Operating Temperature Range... Junction Temperature C Storage Temperature Range C to +15 C Lead Temperature (soldering, 1s)...+3 C Soldering Temperature (reflow) Lead(Pb)-free...+6 C Packages containing lead(pb)...+4 C ( CC = +.4 to +5.5, BATT = 3, T A =, reset not asserted. Typical values are at T A = +5 C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Operating oltage Range, CC or BATT Supply Current (Excluding I OUT ) I SUPPLY in Battery-Backup Mode (Excluding I OUT ) CC, BATT No load (Note ) CC =.8 CC = 3.6 CC = 5.5 BATT =.8, T A = +5 C CC = T A = T A = +5 C T A = CC = 4.75, I OUT 15mA No load, CC > TH, I CC WDI = CC or (MAX636) I SUPPLY BATT Standby Current I BATT 5.5 > CC > ( BATT +.) CC to OUT On-Resistance OUT in Battery-Backup Mode Battery-Switchover Threshold ( CC - BATT ) Reset Threshold CC Falling Reset Delay Reset-Active Timeout Period R ON TH t RP CC = 3.15, I OUT 65mA CC =.38, I OUT 5mA BATT = 4.5, I OUT ma BATT = 3., I OUT 1mA BATT =.5, I OUT 5mA CC < TH MAX636_UT46 MAX636_UT44 MAX636_UT31 MAX636_UT9 MAX636_UT6 MAX636_UT3 CC falling at 1/ms Power-up Power-down BATT -. BATT -.15 BATT µa µa µa Ω m µs 15 8 ms

3 ELECTRICAL CHARACTERISTICS (continued) ( CC = +.4 to +5.5, BATT = 3, T A =, reset not asserted. Typical values are at T A = +5 C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Output oltage I Output oltage OL Reset not asserted SINK = 1.6mA,.3 CC TH(MAX), Output Leakage Current MANUAL (MAX6361 only) MR Input oltage I SINK = 1.6mA,.3 Reset asserted, CC.1 OL BATT = I SINK = 1µA,.4 CC 1. OH IL IH Reset not asserted (MAX636_L only) I SOURCE = 5µA, CC TH(MAX).8 CC I LK MAX636_P, MAX636_H only 1 µa.3 CC.7 CC Pull-Up Resistance kω Minimum Pulse Width 1 µs Glitch Immunity CC = ns MR to Reset Delay CC = ns WATCHDOG INPUT (MAX636 only) Watchdog Timeout Period t WD s Minimum WDI Input Pulse Width t WDI 1 ns IL.3 CC Input oltage IH.7 CC BATT ON (MAX6363 only) Output oltage OL I SINK = 3.mA, BATT =.1.4 Output Short-Circuit Current Sink current, CC = 5 6 ma Source current, BATT µa IN (MAX6364 only) Input Threshold IN Leakage Current ±.1 ±5 na IN to Reset Delay Overdrive voltage = 5m, IN falling 1.5 µs Note 1: All devices are 1% production tested at T A = +5 C. Limits over temperature are guaranteed by design. Note : BATT can be anytime or CC can go down to if BATT is active (except at startup). 3

4 (T A = +5 C, unless otherwise noted.) SUPPLY CURRENT (µa) SUPPLY CURRENT (NO LOAD) BATT = CC = 5. 1 MAX6361 toc1 BATTERY SUPPLY CURRENT (µa) BATTERY SUPPLY CURRENT (BACKUP MODE) BATT =.8 BATT =. Typical Operating Characteristics CC = MAX6361 toc BATT TO OUT ON-RESISTANCE (Ω) BATTERY TO OUT ON-RESISTANCE BATT =. BATT =.8 BATT = 5. 1 I OUT = 5mA CC = MAX6361 toc3 OUT TO OUT ON-RESISTANCE (Ω) CC TO OUT ON-RESISTANCE CC =.3 I OUT = 5mA CC = 4.5 I OUT = 15mA CC = 3. I OUT = 65mA MAX6361 toc4 TIMEOUT PERIOD (ms) TIMEOUT PERIOD MAX6361 toc5 PROPAGATION DELAY (µs) CC TO PROPAGATION DELAY CC FALLING.5/ms 1/ms MAX6361 toc6 15 1/ms 19 WATCHDOG TIMEOUT PERIOD (s) MAX636 WATCHDOG TIMEOUT PERIOD MAX6361toc6a THRESHOLD () THRESHOLD MAX636_46 MAX636_6. MAX6361 toc7 MAXIMUM TRANSIENT DURATION (µs) MAXIMUM TRANSIENT DURATION vs. THRESHOLD OERDRIE MAX636_46 MAX636_6 OCCURS ABOE CURE k 1k THRESHOLD OERDRIE TH - CC (m) MAX6361 toc8 4

5 (T A = +5 C, unless otherwise noted.) BATTERY SUPPLY CURRENT (µa) BATTERY SUPPLY CURRENT vs. SUPPLY OLTAGE BATT =.8 BATT =.5 BATT =.3 TH = CC () MAX6361 toc9 THRESHOLD () Typical Operating Characteristics (continued) MAX6364 IN THRESHOLD 1.34 MAX6361 toc1 PROPAGATION DELAY (µs) MAX6364 IN TO PROPAGATION DELAY OD = 5m 1. Pin Description MAX6361 toc11 PIN NAME MR WDI BATT ON IN CC OUT BATT FUNCTION Active-High Reset Output. is continuously high when CC is below the reset threshold ( TH ), MR is low, or IN is low. It asserts in pulses when the internal watchdog times out. remains high for the reset timeout period (t RP ) after CC rises above the reset threshold, after the manual reset input goes from low to high, after IN goes high, or after the watchdog triggers a reset event. The MAX636_H is an active-high open-drain output. Active-Low Reset Output. is continuously low when CC is below the reset threshold ( TH ), MR is low, or IN is low. It asserts in pulses when the internal watchdog times out. remains low for the reset timeout period (t RP ) after CC rises above the reset threshold, after the manual reset input goes from low to high, after IN goes high, or after the watchdog triggers a reset event. The MAX636_L is an active-low push-pull output while the MAX636_P is an active-low open-drain output. Ground MAX6361 Manual-Reset Input. Maintaining logic low on MR asserts a reset. Reset output remains asserted for at least 15ms (t RP ) after MR transitions from low to high. Leave unconnected or connected to CC if not used. MAX636 Watchdog Input. If WDI remains high or low for longer than the watchdog timeout period (t WD ), the internal watchdog timer runs out and a reset pulse is triggered for the reset timeout period (t RP ) (Figure 1). The internal watchdog clears whenever reset asserts or whenever WDI sees a rising or falling edge. MAX6363 Battery-On Output. BATT ON goes high in battery backup mode. MAX6364 Reset Input. When IN falls below 1.35, reset is asserted. Reset output remains asserted as long as IN is low and for at least 15ms (t RP ) after IN goes high. Supply oltage, to 5.5. Reset is asserted when CC drops below the reset threshold voltage ( TH ). Reset remains asserted until CC rises above TH and for at least 15ms after CC rises above TH. Output. OUT sources from CC when it is above the reset threshold ( TH ), and from the greater of CC or BATT when CC is below TH. Backup-Battery Input. When CC falls below the reset threshold, BATT switches to OUT if BATT is m greater than CC. When CC rises m above BATT, CC switches to OUT. The 4m hysteresis prevents repeated switching if CC falls slowly. 5

6 Detailed Description The Typical Operating Circuit shows a typical connection for the family. OUT powers the static random-access memory (SRAM). OUT is internally connected to CC if CC is greater than the reset threshold, or to the greater of CC or BATT when CC is less than the reset threshold. OUT can supply up to 15mA from CC. When CC is higher than BATT, the BATT ON (MAX6363) output is low. When CC is lower than BATT, an internal MOSFET connects the backup battery to OUT. The on-resistance of the MOSFET is a function of backup-battery voltage and is shown in the Battery to Out On-Resistance vs. Temperature graph in the Typical Operating Characteristics section. Backup-Battery Switchover In a brownout or power failure, it may be necessary to preserve the contents of the RAM. With a backup battery installed at BATT, the automatically switch the RAM to backup power when CC falls. The MAX6363 has a BATT ON output that goes high when in battery-backup mode. These devices require two conditions before switching to batterybackup mode: 1) CC must be below the reset threshold. ) CC must be below BATT. Table 1 lists the status of the inputs and outputs in battery-backup mode. The device will not power up if the only voltage source is on BATT. OUT will only power up from CC at startup. Manual Reset Input (MAX6361 Only) Many µp-based products require manual reset capability, allowing the operator, a test technician, or external logic circuitry to initiate a reset. For the MAX6361, a logic low on MR asserts reset. Reset remains asserted while MR is low, and for a minimum of 15ms (t RP ) after it returns high. MR has an internal kω pull-up resistor to CC. This input can be driven with TTL/CMOS logic levels or with open-drain/collector outputs. Connect a normally open momentary switch from MR to to create a manual reset function; external debounce circuitry is not required. If MR is driven from long cables or the device is used in a noisy environment, connect a.1µf capacitor from MR to to provide additional noise immunity. Watchdog Input (MAX636 Only) The watchdog monitors µp activity through the input WDI. If the µp becomes inactive, the reset output is asserted in pulses. To use the watchdog function, connect WDI to a bus line or µp I/O line. A change of state (high to low or low to high) within the watchdog timeout period (t WD ) with a 1ns minimum pulse width clears the watchdog timer. If WDI remains high or low for longer than the watchdog timeout period, the internal watchdog timer runs out and a reset pulse is triggered for the reset timeout period (t RP ). The internal watchdog timer clears whenever reset asserts or the WDI sees a rising or falling edge within the watchdog timeout period. If WDI remains in a high or low state for an extended period of time, a reset pulse asserts after every watchdog timeout period (t WD ) (Figure 1). Reset In (MAX6364 Only) IN is compared to an internal 1.35 reference. If the voltage at IN is less than 1.35, reset is asserted. The IN comparator may be used as an undervoltage detector to signal a failing power supply. It can also be used as a secondary power-supply reset monitor. To program the reset threshold ( RTH ) of the secondary power supply, use the following equation (see Typical Operating Circuit): where REF = To simplify the resistor selection, choose a value for R and calculate R1: Since the input current at IN is 5nA (max), large values (up to 1MΩ) can be used for R with no significant loss in accuracy. For example, in the Typical Table 1. Input and Output Status in Battery-Backup Mode PIN CC OUT BATT / BATT ON MR, IN, WDI R1 RTH = REF + 1 R [ ] R1 = R ( RTH / REF) 1 STATUS Disconnected from OUT Connected to BATT Connected to OUT. Current drawn from the battery is less than 1µA (at BATT =.8, excluding I OUT ) when CC =. Asserted High state Inputs ignored 6

7 Operating Circuit, the MAX636 monitors two supply voltages. To monitor the secondary 5 logic or analog supply with a 4.6 nominal programmed reset threshold, choose R = 1kΩ, and calculate R1 = 73kΩ. Reset Output A µp s reset input starts the µp in a known state. The µp supervisory circuits assert a reset to prevent code-execution errors during powerup, power-down, and brownout conditions. is guaranteed to be a logic low or high depending on the device chosen (see Ordering Information). or asserts when CC is below the reset threshold and for at least 15ms (t RP ) after CC rises above the reset threshold. or also asserts when MR is low (MAX6361) and when IN is less than 1.35 (MAX6364). The MAX636 watchdog function will cause (or ) to assert in pulses following a watchdog timeout (Figure 1). Applications Information Operation Without a Backup Power Source The were designed for batterybacked applications. If a backup battery is not used, connect CC to OUT and connect BATT to. Replacing the Backup Battery If BATT is decoupled with a.1µf capacitor to ground, the backup power source can be removed while CC remains valid without danger of triggering a reset pulse. The device does not enter battery-backup mode when CC stays above the reset threshold voltage. Negative-Going CC Transients These supervisors are relatively immune to short-duration, negative-going CC transients. Resetting the µp when CC experiences only small glitches is usually not desirable. The Typical Operating Characteristics section shows a graph of Maximum Transient Duration vs. Reset Threshold Overdrive for which reset is not asserted. The graph was produced using negative-going CC pulses, starting at CC and ending below the reset threshold by the magnitude indicated (reset threshold overdrive). The graph shows the maximum pulse width that a negative-going CC transient can typically have without triggering a reset pulse. As the amplitude of the transient increases (i.e., goes further below the reset threshold), the maximum allowable pulse width decreases. Typically, a CC transient that goes 1m below the reset threshold and lasts for 3µs will not trigger a reset pulse. A.1µF bypass capacitor mounted close to the CC pin provides additional transient immunity. WDI t WD t RP t WD t RP t WD = WATCHDOG TIMEOUT PERIOD t RP = TIMEOUT PERIOD Figure 1. MAX636 Watchdog Timeout Period and Reset Active Time 7

8 Watchdog Software Considerations (MAX636 Only) To help the watchdog timer monitor software execution more closely, set and reset the watchdog input at different points in the program, rather than pulsing the watchdog input low-high-low. This technique avoids a stuck loop, in which the watchdog timer would continue to be reset within the loop, keeping the watchdog from timing out. Figure shows an example of a flow diagram where the I/O driving the WDI is set low at the beginning of the program, set high at the beginning of every subroutine or loop, then set low again when the program returns to the beginning. If the program should hang in any subroutine, the problem would quickly be corrected, since the I/O is continually set low and the watchdog timer is allowed to time out, triggering a reset. START SET WDI LOW SUBROUTINE OR PROGRAM LOOP SET WDI HIGH RETURN END Figure. Watchdog Flow Diagram 8

9 MAX6361LUT MAX6361PUT MAX6361HUT MAX636LUT MAX636PUT MAX636HUT MAX6363LUT MAX6363PUT MAX6363HUT MAX6364LUT MAX6364PUT MAX6364HUT MANUAL INPUT MR WATCHDOG INPUT WDI BATT ON IN PUSH- PULL Selector Guide OPEN DRAIN OPEN DRAIN Device Marking Codes TOP MARK TOP MARK TOP MARK TOP MARK MAX6361LUT3 MAX6361LUT6 MAX6361LUT9* MAX6361LUT31 MAX6361LUT44 MAX6361LUT46* MAX6361PUT3 MAX6361PUT6 MAX6361PUT9* MAX6361PUT31 MAX6361PUT44 MAX6361PUT46* MAX6361HUT3 MAX6361HUT6 MAX6361HUT9 MAX6361HUT31 MAX6361HUT44 MAX6361HUT46* AAEI AAEH AAEG AAEF AAEE AAED AAEO AAEN AAEM AAEL AAEK AAEJ AAEU AAET AAES AAER AAEQ AAEP MAX636LUT3 MAX636LUT6 MAX636LUT9* MAX636LUT31 MAX636LUT44 MAX636LUT46* MAX636PUT3 MAX636PUT6 MAX636PUT9* MAX636PUT31 MAX636PUT44 MAX636PUT46* MAX636HUT3 MAX636HUT6 MAX636HUT9 MAX636HUT31 MAX636HUT44 MAX636HUT46* AAFA AAEZ AAEY AAEX AAEW AAE AAFG AAFF AAFE AAFD AAFC AAFB AAFM AAFL AAFK AAFJ AAFI AAFH MAX6363LUT3 MAX6363LUT6 MAX6363LUT9* MAX6363LUT31 MAX6363LUT44 MAX6363LUT46* MAX6363PUT3 MAX6363PUT6 MAX6363PUT9* MAX6363PUT31 MAX6363PUT44 MAX6363PUT46* MAX6363HUT3 MAX6363HUT6 MAX6363HUT9 MAX6363HUT31 MAX6363HUT44 MAX6363HUT46* AAFS AAFR AAFQ AAFP AAFO AAFN AAFY AAFX AAFW AAF AAFU AAFT AAGE AAGD AAGC AAGB AAGA AAFZ MAX6364LUT3 MAX6364LUT6 MAX6364LUT9* MAX6364LUT31 MAX6364LUT44 MAX6364LUT46* MAX6364PUT3 MAX6364PUT6 MAX6364PUT9* MAX6364PUT31 MAX6364PUT44 MAX6364PUT46* MAX6364HUT3 MAX6364HUT6 MAX6364HUT9 MAX6364HUT31 MAX6364HUT44 MAX6364HUT46* AAGK AAGJ AAGI AAGH AAGG AAGF AAGQ AAGP AAGO AAGN AAGM AAGL AAGW AAG AAGU AAGT AAGS AAGR *Sample stock generally held on standard versions only. Contact factory for availability of nonstandard versions. 9

10 TOP IEW, WDI 1 6 BATT MAX636 5 OUT 3 4 CC SOT3-6, BATT ON Pin Configurations (continued) 1 6 BATT, 1 6 BATT MAX6363 MAX OUT 5 OUT 3 4 CC IN 3 4 CC SOT3-6 SOT3-6 Typical Operating Circuit Chip Information PROCESS: BiCMOS UNREGULATED DC OLTAGE.4 TO 5.5 R1 R.1µF 3.6 Li+ BATTERY CC IN MAX6364 BATT OUT.1µF CC µp BUS CC SRAM Package Information For the latest package outline information and land patterns (footprints), go to Note that a +, #, or - in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. U

11 REISION NUMBER REISION DATE DESCRIPTION Revision History PAGES CHANGED 1/ Initial release 3 11/5 Added lead-free information /11 Updated Electrical Characteristics. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. 11 Maxim Integrated Products, 1 San Gabriel Drive, Sunnyvale, CA Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.

AAT3520/2/4 MicroPower Microprocessor Reset Circuit

AAT3520/2/4 MicroPower Microprocessor Reset Circuit General Description Features PowerManager The AAT3520 series of PowerManager products is part of AnalogicTech's Total Power Management IC (TPMIC ) product family. These microprocessor reset circuits are

More information

Microprocessor Supervisory Circuits

Microprocessor Supervisory Circuits 19-4333; Rev 4; 12/05 Microprocessor Supervisory Circuits General Description The reduce the complexity and number of components required for power-supply monitoring and battery-control functions in microprocessor

More information

V CC TOP VIEW. f SSO = 20MHz to 134MHz (DITHERED)

V CC TOP VIEW. f SSO = 20MHz to 134MHz (DITHERED) 19-013; Rev 1; 10/11 0MHz to 13MHz Spread-Spectrum General Description The is a spread-spectrum clock modulator IC that reduces EMI in high clock-frequency-based, digital electronic equipment. Using an

More information

On/Off Controller with Debounce and

On/Off Controller with Debounce and 19-4128; Rev ; 5/8 On/Off Controller with Debounce and General Description The is a pushbutton on/off controller with a single switch debouncer and built-in latch. It accepts a noisy input from a mechanical

More information

STWD100. Watchdog timer circuit. Description. Features. Applications

STWD100. Watchdog timer circuit. Description. Features. Applications Watchdog timer circuit Description Datasheet - production data SOT23-5 (WY) Features SC70-5, SOT323-5 (W8) Current consumption 13 µa typ. Available watchdog timeout periods are 3.4 ms, 6.3 ms, 102 ms,

More information

DS1220Y 16k Nonvolatile SRAM

DS1220Y 16k Nonvolatile SRAM 19-5579; Rev 10/10 NOT RECOENDED FOR NEW DESIGNS 16k Nonvolatile SRAM www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power

More information

Spread-Spectrum Crystal Multiplier DS1080L. Features

Spread-Spectrum Crystal Multiplier DS1080L. Features Rev 1; 3/0 Spread-Spectrum Crystal Multiplier General Description The is a low-jitter, crystal-based clock generator with an integrated phase-locked loop (PLL) to generate spread-spectrum clock outputs

More information

STM6315. Open drain microprocessor reset. Features

STM6315. Open drain microprocessor reset. Features Open drain microprocessor reset Features Low supply current of 1.5µA (typ) ±1.8% reset threshold accuracy (25 C) Guaranteed RST assertion down to V CC = 1.0V Open drain RST output can exceed V CC Power

More information

MAX14760/MAX14762/MAX14764 Above- and Below-the-Rails Low-Leakage Analog Switches

MAX14760/MAX14762/MAX14764 Above- and Below-the-Rails Low-Leakage Analog Switches 19-652; Rev 1; 8/12 EVALUATION KIT AVAILABLE MAX1476// General Description The MAX1476// analog switches are capable of passing bipolar signals that are beyond their supply rails. These devices operate

More information

Cold-Junction-Compensated K-Thermocoupleto-Digital Converter (0 C to +1024 C)

Cold-Junction-Compensated K-Thermocoupleto-Digital Converter (0 C to +1024 C) 19-2235; Rev 1; 3/02 Cold-Junction-Compensated K-Thermocoupleto-Digital General Description The performs cold-junction compensation and digitizes the signal from a type-k thermocouple. The data is output

More information

Push-Pull FET Driver with Integrated Oscillator and Clock Output

Push-Pull FET Driver with Integrated Oscillator and Clock Output 19-3662; Rev 1; 5/7 Push-Pull FET Driver with Integrated Oscillator General Description The is a +4.5V to +15V push-pull, current-fed topology driver subsystem with an integrated oscillator for use in

More information

Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches

Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches 19-2418; Rev ; 4/2 Quad, Rail-to-Rail, Fault-Protected, General Description The are quad, single-pole/single-throw (SPST), fault-protected analog switches. They are pin compatible with the industry-standard

More information

DS1232LP/LPS Low Power MicroMonitor Chip

DS1232LP/LPS Low Power MicroMonitor Chip DSLP/LPS Low Power MicroMonitor Chip www.dalsemi.com FEATURES Super-low power version of DS 50 µa quiescent current Halts and restarts an out-of-control microprocessor Automatically restarts microprocessor

More information

DALLAS DS1233 Econo Reset. BOTTOM VIEW TO-92 PACKAGE See Mech. Drawings Section on Website

DALLAS DS1233 Econo Reset. BOTTOM VIEW TO-92 PACKAGE See Mech. Drawings Section on Website 5V EconoReset www.maxim-ic.com FEATURES Automatically restarts microprocessor after power failure Monitors pushbutton for external override Internal circuitry debounces pushbutton switch Maintains reset

More information

R EXT THERMISTOR. Maxim Integrated Products 1

R EXT THERMISTOR. Maxim Integrated Products 1 19-2219; Rev 0; 2/02 Thermistor-to-Digital Converter General Description The converts an external thermistor s temperature-dependent resistance directly into digital form. The thermistor and an external

More information

DS1225Y 64k Nonvolatile SRAM

DS1225Y 64k Nonvolatile SRAM DS1225Y 64k Nonvolatile SRAM www.maxim-ic.com FEATURES years minimum data retention in the absence of external power Data is automatically protected during power loss Directly replaces 2k x 8 volatile

More information

INTEGRATED CIRCUITS. NE558 Quad timer. Product data Supersedes data of 2001 Aug 03. 2003 Feb 14

INTEGRATED CIRCUITS. NE558 Quad timer. Product data Supersedes data of 2001 Aug 03. 2003 Feb 14 INTEGRATED CIRCUITS Supersedes data of 2001 Aug 03 2003 Feb 14 DESCRIPTION The Quad Timers are monolithic timing devices which can be used to produce four independent timing functions. The output sinks

More information

TS555. Low-power single CMOS timer. Description. Features. The TS555 is a single CMOS timer with very low consumption:

TS555. Low-power single CMOS timer. Description. Features. The TS555 is a single CMOS timer with very low consumption: Low-power single CMOS timer Description Datasheet - production data The TS555 is a single CMOS timer with very low consumption: Features SO8 (plastic micropackage) Pin connections (top view) (I cc(typ)

More information

High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch)

High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch) High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch) DG2301 ishay Siliconix DESCRIPTION The DG2301 is a high-speed, 1-bit, low power, TTLcompatible bus switch. Using sub-micron CMOS technology,

More information

DS1220Y 16k Nonvolatile SRAM

DS1220Y 16k Nonvolatile SRAM Not Recommended for New Design DS122Y 16k Nonvolatile SRAM www.maxim-ic.com FEATURES years minimum data retention in the absence of external power Data is automatically protected during power loss Directly

More information

SELF-OSCILLATING HALF-BRIDGE DRIVER

SELF-OSCILLATING HALF-BRIDGE DRIVER Data Sheet No. PD60029 revj I2155&(PbF) (NOTE: For new designs, we recommend I s new products I2153 and I21531) SELF-OSCILLATING HALF-BIDGE DIE Features Floating channel designed for bootstrap operation

More information

EVALUATION KIT AVAILABLE Broadband, Two-Output, Low-Noise Amplifier for TV Tuner Applications MAX2130. Maxim Integrated Products 1

EVALUATION KIT AVAILABLE Broadband, Two-Output, Low-Noise Amplifier for TV Tuner Applications MAX2130. Maxim Integrated Products 1 9-86; Rev ; 8/ EVALUATION KIT AVAILABLE Broadband, Two-Output, Low-Noise General Description The broadband, low-distortion, low-noise, two-output amplifier performs preamp, loop-out, and buffer functions

More information

DG2302. High-Speed, Low r ON, SPST Analog Switch. Vishay Siliconix. (1-Bit Bus Switch with Level-Shifter) RoHS* COMPLIANT DESCRIPTION FEATURES

DG2302. High-Speed, Low r ON, SPST Analog Switch. Vishay Siliconix. (1-Bit Bus Switch with Level-Shifter) RoHS* COMPLIANT DESCRIPTION FEATURES High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch with Level-Shifter) DG2302 DESCRIPTION The DG2302 is a high-speed, 1-bit, low power, TTLcompatible bus switch. Using sub-micron CMOS technology,

More information

ABRIDGED DATA SHEET EVALUATION KIT AVAILABLE

ABRIDGED DATA SHEET EVALUATION KIT AVAILABLE EVALUATION KIT AVAILABLE General Description DeepCoverM embedded security solutions cloak sensitive data under multiple layers of advanced physical security to provide the most secure key storage possible.

More information

MAX6877/MAX6878/MAX6879

MAX6877/MAX6878/MAX6879 19-3771; Rev 1; 10/05 EVALUATION KIT AVAILABLE Dual-/Triple-Voltage, Power-Supply General Description The multivoltage power trackers/sequencers/supervisors monitor up to three system voltages and provide

More information

Low-Cost, Micropower, SC70/SOT23-8, Microphone Preamplifiers with Complete Shutdown

Low-Cost, Micropower, SC70/SOT23-8, Microphone Preamplifiers with Complete Shutdown 9-9; Rev ; 4/ Low-Cost, Micropower, SC7/SOT23-8, Microphone General Description The are micropower op amps optimized for use as microphone preamplifiers. They provide the ideal combination of an optimized

More information

DM74121 One-Shot with Clear and Complementary Outputs

DM74121 One-Shot with Clear and Complementary Outputs June 1989 Revised July 2001 DM74121 One-Shot with Clear and Complementary Outputs General Description The DM74121 is a monostable multivibrator featuring both positive and negative edge triggering with

More information

C IN MAX1818 2 5 SET ON

C IN MAX1818 2 5 SET ON 19-186; Rev 2; 6/8 5mA Low-Dropout General Description The low-dropout linear regulator operates from a +2.5V to +5.5V supply and delivers a guaranteed 5mA load current with low 12mV dropout. The high-accuracy

More information

±15kV ESD-Protected, 1µA, 250kbps, 3.3V/5V, Dual RS-232 Transceivers with Internal Capacitors

±15kV ESD-Protected, 1µA, 250kbps, 3.3V/5V, Dual RS-232 Transceivers with Internal Capacitors 19-1473; Rev 2; 8/4 ±15k ESD-Protected, 1µA, 25kbps, 3.3/5, Dual General Description The are EIA/TIA-232 and.28/.24 communications interfaces with automatic shutdown/ wake-up features, high data-rate capabilities,

More information

NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter

NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter Description: The NTE2053 is a CMOS 8 bit successive approximation Analog to Digital converter in a 20 Lead DIP type package which uses a differential

More information

High-Speed, Low-Power, 3V/5V, Rail-to-Rail, Single-Supply Comparators MAX941/MAX942/ MAX944. General Description. Features. Ordering Information

High-Speed, Low-Power, 3V/5V, Rail-to-Rail, Single-Supply Comparators MAX941/MAX942/ MAX944. General Description. Features. Ordering Information General Description The MAX941/MAX94/ are single/dual/quad highspeed comparators optimized for systems powered from a 3V or 5V supply. These devices combine high speed, low power, and rail-to-rail inputs.

More information

INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30

INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30 INTEGRATED CIRCUITS IC24 Data Handbook 1997 Jun 30 FEATURES Wide supply voltage range of 1.2 V to 3.6 V In accordance with JEDEC standard no. 8-1A Inputs accept voltages up to 5.5 V CMOS low power consumption

More information

30V Internal Switch LCD Bias Supply

30V Internal Switch LCD Bias Supply 19-1666; Rev 1; 1/3 3V Internal Switch LCD Bias Supply General Description The boost converter contains a.5a internal switch in a tiny 6-pin SOT23 package. The IC operates from a +2.4V to +5.5V supply

More information

MM74HC4538 Dual Retriggerable Monostable Multivibrator

MM74HC4538 Dual Retriggerable Monostable Multivibrator MM74HC4538 Dual Retriggerable Monostable Multivibrator General Description The MM74HC4538 high speed monostable multivibrator (one shots) is implemented in advanced silicon-gate CMOS technology. They feature

More information

DS1386/DS1386P RAMified Watchdog Timekeeper

DS1386/DS1386P RAMified Watchdog Timekeeper DS1386/DS1386P RAMified Watchdog Timekeeper www.maxim-ic.com GENERAL DESCRIPTION The DS1386 is a nonvolatile static RAM with a full-function real-time clock (RTC), alarm, watchdog timer, and interval timer

More information

TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER. Features

TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER. Features DATASHEET ICS280 Description The ICS280 field programmable spread spectrum clock synthesizer generates up to four high-quality, high-frequency clock outputs including multiple reference clocks from a low-frequency

More information

+5 V Powered RS-232/RS-422 Transceiver AD7306

+5 V Powered RS-232/RS-422 Transceiver AD7306 a FEATURES RS- and RS- on One Chip Single + V Supply. F Capacitors Short Circuit Protection Excellent Noise Immunity Low Power BiCMOS Technology High Speed, Low Skew RS- Operation C to + C Operations APPLICATIONS

More information

AP331A XX G - 7. Lead Free G : Green. Packaging (Note 2)

AP331A XX G - 7. Lead Free G : Green. Packaging (Note 2) Features General Description Wide supply Voltage range: 2.0V to 36V Single or dual supplies: ±1.0V to ±18V Very low supply current drain (0.4mA) independent of supply voltage Low input biasing current:

More information

High-Speed, 5 V, 0.1 F CMOS RS-232 Driver/Receivers ADM202/ADM203

High-Speed, 5 V, 0.1 F CMOS RS-232 Driver/Receivers ADM202/ADM203 a FEATURES kb Transmission Rate ADM: Small (. F) Charge Pump Capacitors ADM3: No External Capacitors Required Single V Power Supply Meets EIA-3-E and V. Specifications Two Drivers and Two Receivers On-Board

More information

CURRENT LIMITING SINGLE CHANNEL DRIVER V OFFSET. Packages

CURRENT LIMITING SINGLE CHANNEL DRIVER V OFFSET. Packages Features Floating channel designed for bootstrap operation Fully operational to +5V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 12 to 18V Undervoltage lockout Current

More information

Features. V PP IN V CC3 IN V CC5 IN (opt) EN0 EN1 MIC2562

Features. V PP IN V CC3 IN V CC5 IN (opt) EN0 EN1 MIC2562 MIC2562A /CardBus Socket Power Controller General Description The MIC2562A (Personal Computer Memory Card International Association) and CardBus power controller handles all PC Card slot power supply pins,

More information

ICS514 LOCO PLL CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET

ICS514 LOCO PLL CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET DATASHEET ICS514 Description The ICS514 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output from a 14.31818 MHz crystal or clock input. The name LOCO stands for

More information

24-Channel Automotive Switch Monitor

24-Channel Automotive Switch Monitor 9-4464; Rev ; 2/9 EVALUATION KIT AVAILABLE 24-Channel Automotive Switch Monitor General Description The is a 24-channel automotive contact monitor designed as an interface between mechanical switches and

More information

AAT4280 Slew Rate Controlled Load Switch

AAT4280 Slew Rate Controlled Load Switch General Description Features SmartSwitch The AAT4280 SmartSwitch is a P-channel MOSFET power switch designed for high-side load switching applications. The P-channel MOSFET device has a typical R DS(ON)

More information

1-Mbit (128K x 8) Static RAM

1-Mbit (128K x 8) Static RAM 1-Mbit (128K x 8) Static RAM Features Pin- and function-compatible with CY7C109B/CY7C1009B High speed t AA = 10 ns Low active power I CC = 80 ma @ 10 ns Low CMOS standby power I SB2 = 3 ma 2.0V Data Retention

More information

SG6516 PC Power Supply Supervisors

SG6516 PC Power Supply Supervisors SG6516 PC Power Supply Supervisors Features Two 12V Sense Input Pins: VS12 and VS12B Over-Voltage Protection (OVP) for 3.3V, 5V, and two 12V Over-Current Protection (OCP) for 3.3V, 5V, and two 12V Under-Voltage

More information

480mA White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash

480mA White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash 19-3326; Rev 1; 8/05 EVALUATION KIT AVAILABLE 480mA White LED 1x/1.5x/2x Charge Pump for General Description The charge pump drives up to 8 white LEDs with regulated constant current for uniform intensity.

More information

SG6520 FEATURES DESCRIPTION TYPICAL APPLICATION. Product Specification. PC Power Supply Supervisors

SG6520 FEATURES DESCRIPTION TYPICAL APPLICATION. Product Specification. PC Power Supply Supervisors FEATURES Two 12V sense input pins: VS12 and VS12B Over voltage protection (OVP) for 3.3V, 5V and two 12V Over current protection (OCP) for 3.3V, 5V and two 12V Under voltage protection (UVP) for 3.3V,

More information

Quad 2-input NAND Schmitt trigger

Quad 2-input NAND Schmitt trigger Rev. 9 15 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Applications The is a quad two-input NAND gate. Each input has a Schmitt trigger circuit. The gate switches

More information

256K (32K x 8) Static RAM

256K (32K x 8) Static RAM 256K (32K x 8) Static RAM Features High speed: 55 ns and 70 ns Voltage range: 4.5V 5.5V operation Low active power (70 ns, LL version) 275 mw (max.) Low standby power (70 ns, LL version) 28 µw (max.) Easy

More information

IN1M101 Precision AC Brown-out Supervisor IC

IN1M101 Precision AC Brown-out Supervisor IC Precision AC Brown-out Supervisor IC Rev.1.1 03 30 2011 Specification General Description provides a precise comparator to detect the rectified AC voltage, which could protect the SPS when AC voltage is

More information

MAX1501 Highly Integrated, Linear Battery Charger with Thermal Regulation for Portable Applications

MAX1501 Highly Integrated, Linear Battery Charger with Thermal Regulation for Portable Applications General Description The MAX1501 intelligent, constant-current, constantvoltage (CCCV), temperature-regulated battery charger charges a single lithium-ion (Li+) cell or three-cell NiMH/NiCd batteries. The

More information

www.jameco.com 1-800-831-4242

www.jameco.com 1-800-831-4242 Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. 19-0028; Rev 3; 9/01 Monolithic CMOS Analog Multiplexers General Description

More information

DS1307ZN. 64 x 8 Serial Real-Time Clock

DS1307ZN. 64 x 8 Serial Real-Time Clock DS137 64 x 8 Serial Real-Time Clock www.maxim-ic.com FEATURES Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap-year compensation valid

More information

High-Bandwidth, T1/E1, SPST Analog Switches

High-Bandwidth, T1/E1, SPST Analog Switches 19-3951; Rev 2; 1/7 High-Bandwidth,, SPST Analog Switches General Description The high-bandwidth, low-on-resistance, quad-spst analog switches are designed to serve as integrated protection switches for

More information

Features. Applications

Features. Applications LM555 Timer General Description The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the

More information

+3.3V/+5V, 8-Channel Relay Drivers with Fast Recovery Time and Power-Save Mode

+3.3V/+5V, 8-Channel Relay Drivers with Fast Recovery Time and Power-Save Mode 19-3789; Rev 0; 8/05 +3.3V/+5V, 8-Channel Relay Drivers with Fast General Description The 8-channel relay drivers offer built-in kickback protection and drive +3V/+5V nonlatching or dual-coil-latching

More information

Real Time Clock Module with I2C Bus

Real Time Clock Module with I2C Bus Moisture Seitivity Level: MSL=1 FEATURES: With state-of-the-art RTC Technology by Micro Crystal AG RTC module with built-in crystal oscillating at 32.768 khz 3 timekeeping current at 3 Timekeeping down

More information

HCC/HCF4032B HCC/HCF4038B

HCC/HCF4032B HCC/HCF4038B HCC/HCF4032B HCC/HCF4038B TRIPLE SERIAL ADDERS INERT INPUTS ON ALL ADDERS FOR SUM COMPLEMENTING APPLICATIONS FULLY STATIC OPERATION...DC TO 10MHz (typ.) @ DD = 10 BUFFERED INPUTS AND OUTPUTS SINGLE-PHASE

More information

www.jameco.com 1-800-831-4242

www.jameco.com 1-800-831-4242 Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. www.maxim-ic.com FEATURES 10 years minimum data retention in the absence

More information

DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs

DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs General Description This device contains two independent positive-edge-triggered D-type flip-flops with

More information

ICS650-44 SPREAD SPECTRUM CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET

ICS650-44 SPREAD SPECTRUM CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET DATASHEET ICS650-44 Description The ICS650-44 is a spread spectrum clock synthesizer intended for video projector and digital TV applications. It generates three copies of an EMI optimized 50 MHz clock

More information

Supply voltage Supervisor TL77xx Series. Author: Eilhard Haseloff

Supply voltage Supervisor TL77xx Series. Author: Eilhard Haseloff Supply voltage Supervisor TL77xx Series Author: Eilhard Haseloff Literature Number: SLVAE04 March 1997 i IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to

More information

MC33064DM 5 UNDERVOLTAGE SENSING CIRCUIT

MC33064DM 5 UNDERVOLTAGE SENSING CIRCUIT Order this document by MC3464/D The MC3464 is an undervoltage sensing circuit specifically designed for use as a reset controller in microprocessor-based systems. It offers the designer an economical solution

More information

DS1621 Digital Thermometer and Thermostat

DS1621 Digital Thermometer and Thermostat www.maxim-ic.com FEATURES Temperature measurements require no external components Measures temperatures from -55 C to +125 C in 0.5 C increments. Fahrenheit equivalent is -67 F to 257 F in 0.9 F increments

More information

NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description

NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable

More information

VN05N. High side smart power solid state relay PENTAWATT. Features. Description

VN05N. High side smart power solid state relay PENTAWATT. Features. Description High side smart power solid state relay Features Type V DSS R DS(on) I OUT V CC VN05N 60 V 0.18 Ω 13 A 26 V Output current (continuous): 13A @ Tc=25 C 5V logic level compatible input Thermal shutdown Under

More information

Low-power configurable multiple function gate

Low-power configurable multiple function gate Rev. 7 10 September 2014 Product data sheet 1. General description The provides configurable multiple functions. The output state is determined by eight patterns of 3-bit input. The user can choose the

More information

ICS379. Quad PLL with VCXO Quick Turn Clock. Description. Features. Block Diagram

ICS379. Quad PLL with VCXO Quick Turn Clock. Description. Features. Block Diagram Quad PLL with VCXO Quick Turn Clock Description The ICS379 QTClock TM generates up to 9 high quality, high frequency clock outputs including a reference from a low frequency pullable crystal. It is designed

More information

CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset

CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset October 1987 Revised March 2002 CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset General Description The CD4027BC dual J-K flip-flops are monolithic complementary MOS (CMOS) integrated circuits

More information

HT9170 DTMF Receiver. Features. General Description. Selection Table

HT9170 DTMF Receiver. Features. General Description. Selection Table DTMF Receiver Features Operating voltage: 2.5V~5.5V Minimal external components No external filter is required Low standby current (on power down mode) General Description The HT9170 series are Dual Tone

More information

CD40174BC CD40175BC Hex D-Type Flip-Flop Quad D-Type Flip-Flop

CD40174BC CD40175BC Hex D-Type Flip-Flop Quad D-Type Flip-Flop Hex D-Type Flip-Flop Quad D-Type Flip-Flop General Description The CD40174BC consists of six positive-edge triggered D- type flip-flops; the true outputs from each flip-flop are externally available. The

More information

HCC4541B HCF4541B PROGRAMMABLE TIMER

HCC4541B HCF4541B PROGRAMMABLE TIMER HCC4541B HCF4541B PROGRAMMABLE TIMER 16 STAGE BINARI COUNTER LOW SYMMETRICAL OUTPUT RESISTANCE, TYPICALLY 100 OHM AT DD = 15 OSCILLATOR FREQUENCY RANGE : DC TO 100kHz AUTO OR MASTER RESET DISABLES OSCIL-

More information

200mA, Automotive, Ultra-Low Quiescent Current, Linear Regulator

200mA, Automotive, Ultra-Low Quiescent Current, Linear Regulator EVALUATION KIT AVAILABLE MAX1691 General Description The MAX1691 ultra-low quiescent current, high-voltage linear regulator is ideal for use in automotive and batteryoperated systems. The device operates

More information

MAX14759/MAX14761/MAX14763 Above- and Below-the-Rails Low On-Resistance Analog Switches

MAX14759/MAX14761/MAX14763 Above- and Below-the-Rails Low On-Resistance Analog Switches 19-651; Rev ; 9/11 /MX14761/ General Description The /MX14761/ analog switches are capable of passing bipolar signals that are beyond their supply rails. These devices operate from a single +3.V to +5.5V

More information

Low Voltage, Resistor Programmable Thermostatic Switch AD22105

Low Voltage, Resistor Programmable Thermostatic Switch AD22105 a Low Voltage, Resistor Programmable Thermostatic Switch AD22105 FEATURES User-Programmable Temperature Setpoint 2.0 C Setpoint Accuracy 4.0 C Preset Hysteresis Wide Supply Range (+2.7 V dc to +7.0 V dc)

More information

1.5A Ultra Low Dropout Linear Regulator TJ3965

1.5A Ultra Low Dropout Linear Regulator TJ3965 FEATURES Ultra Low Dropout Voltage Low Ground Pin Current Excellent Line and Load Regulation Guaranteed Output Current of 1.5A Available in MSOP8, SOP8, SOP8PP, SOT223, TO252, TO263, TO220, and SOT89 Packages

More information

NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description

NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable

More information

1 TO 4 CLOCK BUFFER ICS551. Description. Features. Block Diagram DATASHEET

1 TO 4 CLOCK BUFFER ICS551. Description. Features. Block Diagram DATASHEET DATASHEET 1 TO 4 CLOCK BUFFER ICS551 Description The ICS551 is a low cost, high-speed single input to four output clock buffer. Part of IDT s ClockBlocks TM family, this is our lowest cost, small clock

More information

HEF4011B. 1. General description. 2. Features and benefits. 3. Ordering information. 4. Functional diagram. Quad 2-input NAND gate

HEF4011B. 1. General description. 2. Features and benefits. 3. Ordering information. 4. Functional diagram. Quad 2-input NAND gate Rev. 6 10 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a quad 2-input NAND gate. The outputs are fully buffered for the highest noise

More information

Constant Voltage and Constant Current Controller for Adaptors and Battery Chargers

Constant Voltage and Constant Current Controller for Adaptors and Battery Chargers TECHNICAL DATA Constant Voltage and Constant Current Controller for Adaptors and Battery Chargers IK3051 Description IK3051 is a highly integrated solution for SMPS applications requiring constant voltage

More information

High-Speed, 5 V, 0.1 F CMOS RS-232 Drivers/Receivers ADM222/ADM232A/ADM242

High-Speed, 5 V, 0.1 F CMOS RS-232 Drivers/Receivers ADM222/ADM232A/ADM242 a FEATURES 200 kb/s Transmission Rate Small (0. F) Charge Pump Capacitors Single V Power Supply Meets All EIA-232-E and V.2 Specifications Two Drivers and Two Receivers On-Board DC-DC Converters V Output

More information

10/100/1000 Base-T Ethernet LAN Switch

10/100/1000 Base-T Ethernet LAN Switch 19-377; Rev 2; 8/7 1/1/1 Base-T Ethernet LAN Switch General Description The MAX89/MAX891/MAX892 high-speed analog switches meet the needs of 1/1/1 Base-T applications. These devices switch the signals

More information

TLI4946. Datasheet TLI4946K, TLI4946-2K, TLI4946-2L. Sense and Control. May 2009

TLI4946. Datasheet TLI4946K, TLI4946-2K, TLI4946-2L. Sense and Control. May 2009 May 2009 TLI4946 High Precision Hall Effect Latches for Industrial and Consumer Applications TLI4946K, TLI4946-2K, TLI4946-2L Datasheet Rev. 1.0 Sense and Control Edition 2009-05-04 Published by Infineon

More information

PS323. Precision, Single-Supply SPST Analog Switch. Features. Description. Block Diagram, Pin Configuration, and Truth Table. Applications PS323 PS323

PS323. Precision, Single-Supply SPST Analog Switch. Features. Description. Block Diagram, Pin Configuration, and Truth Table. Applications PS323 PS323 Features ÎÎLow On-Resistance (33-ohm typ.) Minimizes Distortion and Error Voltages ÎÎLow Glitching Reduces Step Errors in Sample-and-Holds. Charge Injection, 2pC typ. ÎÎSingle-Supply Operation (+2.5V to

More information

DM74LS112A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flop with Preset, Clear, and Complementary Outputs

DM74LS112A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flop with Preset, Clear, and Complementary Outputs August 1986 Revised March 2000 DM74LS112A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flop with Preset, Clear, and Complementary General Description This device contains two independent negative-edge-triggered

More information

0.9V Boost Driver PR4403 for White LEDs in Solar Lamps

0.9V Boost Driver PR4403 for White LEDs in Solar Lamps 0.9 Boost Driver for White LEDs in Solar Lamps The is a single cell step-up converter for white LEDs operating from a single rechargeable cell of 1.2 supply voltage down to less than 0.9. An adjustable

More information

DM74LS05 Hex Inverters with Open-Collector Outputs

DM74LS05 Hex Inverters with Open-Collector Outputs Hex Inverters with Open-Collector Outputs General Description This device contains six independent gates each of which performs the logic INVERT function. The open-collector outputs require external pull-up

More information

LDO03C/LDO06C/LDO10C

LDO03C/LDO06C/LDO10C NEW LDO03C/LDO06C/LDO10C A p p l i c a t i o n N o t e 1 8 6 1. Introduction 2 2. Models Features 2 3. General Description Electrical Description 2 Physical Construction 2 4. Features and Functions Wide

More information

LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators

LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators Low Power Low Offset Voltage Quad Comparators General Description The LM139 series consists of four independent precision voltage comparators with an offset voltage specification as low as 2 mv max for

More information

AZV5002. Low Power Audio Jack Detector with SEND/END Detection in Miniaturized Package. Description. Pin Assignments. Features NEW PRODUCT

AZV5002. Low Power Audio Jack Detector with SEND/END Detection in Miniaturized Package. Description. Pin Assignments. Features NEW PRODUCT Low Power Audio Jack Detector with SEND/END Detection in Miniaturized Package Description Pin Assignments The is a low power and cost effective headset detection IC with a comparator with internal hysteresis,

More information

FM75 Low-Voltage Two-Wire Digital Temperature Sensor with Thermal Alarm

FM75 Low-Voltage Two-Wire Digital Temperature Sensor with Thermal Alarm Low-Voltage Two-Wire Digital Temperature Sensor with Thermal Alarm Features User Configurable to 9, 10, 11 or 12-bit Resolution Precision Calibrated to ±1 C, 0 C to 100 C Typical Temperature Range: -40

More information

IS31LT3360 40V/1.2A LED DRIVER WITH INTERNAL SWITCH. January 2014

IS31LT3360 40V/1.2A LED DRIVER WITH INTERNAL SWITCH. January 2014 40V/1.2A LED DRIVER WITH INTERNAL SWITCH January 2014 GENERAL DESCRIPTION The IS31LT3360 is a continuous mode inductive step-down converter, designed for driving a single LED or multiple series connected

More information

SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS

SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS 8 TO 35 V OPERATION 5.1 V REFERENCE TRIMMED TO ± 1 % 100 Hz TO 500 KHz OSCILLATOR RANGE SEPARATE OSCILLATOR SYNC TERMINAL ADJUSTABLE DEADTIME CONTROL INTERNAL

More information

STCS1A. 1.5 A max constant current LED driver. Features. Applications. Description

STCS1A. 1.5 A max constant current LED driver. Features. Applications. Description 1.5 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 1.5 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic DFN8 (3 x 3

More information

DS1721 2-Wire Digital Thermometer and Thermostat

DS1721 2-Wire Digital Thermometer and Thermostat www.dalsemi.com FEATURES Temperature measurements require no external components with ±1 C accuracy Measures temperatures from -55 C to +125 C; Fahrenheit equivalent is -67 F to +257 F Temperature resolution

More information

40 V, 200 ma NPN switching transistor

40 V, 200 ma NPN switching transistor Rev. 01 21 July 2009 Product data sheet BOTTOM VIEW 1. Product profile 1.1 General description NPN single switching transistor in a SOT883 (SC-101) leadless ultra small Surface-Mounted Device (SMD) plastic

More information

High and Low Side Driver

High and Low Side Driver High and Low Side Driver Features Product Summary Floating channel designed for bootstrap operation Fully operational to 200V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range

More information

PIN CONFIGURATION FEATURES ORDERING INFORMATION ABSOLUTE MAXIMUM RATINGS. D, F, N Packages

PIN CONFIGURATION FEATURES ORDERING INFORMATION ABSOLUTE MAXIMUM RATINGS. D, F, N Packages DESCRIPTION The µa71 is a high performance operational amplifier with high open-loop gain, internal compensation, high common mode range and exceptional temperature stability. The µa71 is short-circuit-protected

More information

PACKAGE OUTLINE DALLAS DS2434 DS2434 GND. PR 35 PACKAGE See Mech. Drawings Section

PACKAGE OUTLINE DALLAS DS2434 DS2434 GND. PR 35 PACKAGE See Mech. Drawings Section PRELIMINARY DS2434 Battery Identification Chip FEATURES Provides unique ID number to battery packs PACKAGE OUTLINE Eliminates thermistors by sensing battery temperature on chip DALLAS DS2434 1 2 3 256

More information