Price groups and supply availability 5 General notes and abbreviations 6 Planning guide 11. Heating, air-conditioning, cooling 13

Transcription

1 Contents Heating, air-conditioning, cooling Price groups and supply availability 5 General notes and abbreviations 6 Planning guide 11 Heating, air-conditioning, cooling 13 Glandless high-efficiency pumps Single pumps Wilo-Stratos PICO 13 Coming soon! Wilo-Yonos PICO 14 Wilo-Stratos ECO...-BMS 15 Wilo-Stratos 16 Double pumps Wilo-Stratos-D 18 Heizung, Klima, Kälte Glandless automatic pumps Single pumps Wilo-Smart 19 Glandless standard pumps Single pumps Wilo-Star-RS 2 Double pumps Wilo-Star-RSD 21 Single pumps Wilo-TOP-S 22 Double pumps Wilo-TOP-SD 24 Wilo-TOP-D 26 Wasserversorgung Glanded high-efficiency pumps Single pumps Wilo-Stratos GIGA 28 Glanded energy-saving pumps Single pumps Wilo-VeroLine-IP-E 3 Wilo-CronoLine-IL-E 32 Double pumps Wilo-VeroTwin-DP-E 36 Wilo-CronoTwin-DL-E 38 Abwasser Glanded standard pumps Single pumps Wilo-VeroLine-IPL 41 Wilo-CronoLine-IL 44 Double pumps Wilo-VeroTwin-DPL 52 Wilo-CronoTwin-DL 55 Glanded special pumps Single pumps Wilo-VeroLine-IPS 6 Wilo-VeroLine-IPH-W/-O 61 Glanded monobloc pumps Single pumps Wilo-BAC 65 Wilo-CronoBloc-BL 66 Schalt- und Regelgeräte/ Pumpenmanagement Wasserversorgung 3

2 Contents Heating, air-conditioning, cooling Glanded norm pumps Single pumps Wilo-Crono-Norm-NL 71 Wilo-VeroNorm-NPG 89 Glanded axially split case pumps Single pumps Wilo-SCP 91 Solar thermal, geothermal, systems 92 Glandless high-efficiency pumps Single pumps Wilo-Stratos ECO-ST 92 Glandless high-efficiency pumps Single pumps Wilo-Star-ST 93 Secondary hot water 94 Glandless high-efficiency pumps Single pumps Wilo-Star-Z NOVA 94 Wilo-Stratos ECO-Z 95 Wilo-Stratos-Z 96 Glandless standard pumps Single pumps Wilo-Star-Z 98 Wilo-TOP-Z 99 Glanded special pumps Single pumps Wilo-VeroLine-IP-Z 11 Accessories 12 Operating and service unit 12 Threaded pipe unions, mounting feet, blind plates Stratos-D/TOP-SD 13 Adapter fittings, flanged rings, flange pieces 16 Wilo modular concept (spare motors RMOT) 19 Mounting feet, special mechanical seals 117 Blind plates for glanded pumps, differential pressure sensors 118 Control/Device, switchgears Plug-in modules, differential pressure switches, motor protection, accessories 121 Inverters Stand Alone Inverter Drive 122 Pump control Wilo-interface modules (IF-Module-Stratos, IF-Module) 123 Wilo-Protect-Module-C 125 Systems 127 Condensate lifting units Wilo-DrainLift Con 127 4

3 Price groups and supply availability Price group key and supply availability Price group W Price group W1 Price group W2 Price group W3 All small screw-end pumps All Star pump types: Star-RS, Star-Z NOVA, Star-RSD, Star-Z 15TT up to Z 25/6, Star-ST, Star-RSG, Star-ZD, Smart High-efficiency pumps, electronically controlled flange-end pumps and big screw-end pumps Stratos, Stratos-D, Stratos-Z, Stratos-ZD, spare motors for above-mentioned pumps Yonos PICO, Stratos PICO, Stratos ECO-BMS, Stratos ECO-Z, Stratos ECO-ST, spare motors for TOP-E, TOP-ED and TOP-EV Standard flange-end and big screw-end pumps TOP-S, TOP-SD, TOP-D, TOP-Z, spare motors for above-mentioned pumps, spare motors for RP, P, DOP Accessories for pump control DigiCon-LBF, Protect module, CC-/CCe system, VR-HVAC system, plug-in modules, full motor protection, screwed connections, adapters, capacitors, Wilo-Safe Price group W4 Price group W5 Price group W6 Price group W7 Glanded high-efficiency pumps VeroLine-IP-E, VeroTwin- DP-E, CronoLine-IL-E, CronoTwin-DL-E, DL-E Standard-Pumpen VeroLine-IPL, IP-Z, IPS, VeroLine-IPH-W, IPH-O, VeroTwin-DPL, CronoLine-IL, CronoTwin-DL, CronoBloc-BL, BAC, CronoNorm-NL, NPG, SCP Water supply Pumps and systems for house and garden, rainwater utilisation, submersible pumps, high-pressure centrifugal pumps, accessories Drainage/sewage Pumps for wastewater/drainage (except for Wilo-EMU KS see price group W8), pumps for sewage/faeces (except for Wilo-EMU FA - see price group W8), lifting units for condensate/ wastewater/drainage, lifting units for sewage/faeces, synthetic pumps stations System technology sanitary engineering Pressure boosting and fire fighting systems, accessories Price group W8 Price group W9/WD Price group WG Price group WE Pumps for wastewater: Wilo-EMU KS, sewage/ faeces: Wilo-EMU FA Service Spare parts, services, customer service Geniax All components of the decentralised pump system Wilo-Geniax High-efficiency glanded pumps Stratos-GIGA Supply availability key ]=supply availability L=normally available ex stock C=components available ex stock, assembly to order within approx. 2 weeks K=components available ex stock, assembly to order within approx. 4 weeks A = delivery time on request This price list supersedes all previous price documentation which thus become invalid. All product illustrations of respective product series are symbolic presentations only. Effective from 1 October 211 in Germany. Article numbers in bold type These products were modified or are new. 5

4 General notes and abbreviations Abbreviation Meaning 1~ 1-phase current 3~ 3-phase current blsf BACnet Blocking current-proof, no motor protection required Internationally defined company-neutral standard for data communication in building automation systems (ISO ). CAN (Controller Area Network) - Multi master bus system, in which several equal CAN-devices may communicate via a 2-core bus within very short cycle CAN times. The Wilo-CAN bus includes a CANopen Standard (EN ) which is independent of the supplier. DM Three-phase motor, 3~ DN Δp Δp-c Δp-T Δp-v ΔT EBM ECM technology Nominal diameter of the flange connection Differential pressure Control mode for constant differential pressure Control mode for differential pressure control depending on the fluid temperature Control mode for variable differential pressure Control mode for differential temperature Individual run signal Electronically commutated motor with new wet rotor encapsulation, newly developed glandless drive concept for high-efficiency pumps EM Single-phase motor, 1~ EnEV ErP ESM Ext. Off Ext. Min FI BA Geniax-BUS GRD/GLRD dh H IF Int. MS IR German Energy Conservation Legislation It applies to energy-related products. ErP Directive 29/125/EC establishing a framework for the setting of environmentally-responsible requirements for energy-driven products. Formerly the Ecodesign Directive (EuP Directive 25/32/EC). Individual fault signal Overriding Off control input Control input Overriding Min, e. g. for automatic setback operation Residual current-operated protective device Building automation Master/slave BUS system, specified for the requirements of the Geniax system, derived from CAN-BUS technology. Up to 252 Geniax components can communicate with a server with short cycle times via a 2- wire BUS. The Geniax BUS is not compatible with other CAN-BUS systems. Mechanical seal Degree of German water hardness; formerly used unit for assessing the water hardness. Is no longer used since the SI-unit mmol/l has been introduced. Conversion: 1 dh =.1783 mmol/l Delivery head Interface Infrared interface Abbreviation KDS KLF Internal motor protection: pumps with internal protection against unacceptably high winding temperatures Cataphoretic coating KTW LON Modbus mmol/l MOT P 1 PELV PLR Q (= ) RMOT SELV SBM SSM Control input, - 1 V TrinkwV 21 VDI 235 Wilo-Control WRAS WSK X Meaning Capacitor PTC thermistor sensor Cataphoretic coating (electrophoretically deposited paint, EDP): paintwork with high adhesive strength for long-lasting corrosion protection Approval for products with plastics, for utilisation in potable water applications Local Operating Network (open data bus system, standardised and independent of any single manufacturer, in LONWorks networks) Communication protocol based on a master/slave architecture. Ethernet and RS485 are used as the media of transmission. Widespread in industrial and building automation applications. Millimols per litre; SI unit for assessing water hardness (total hardness, or concentration of alkaline earth ions) Motor module (drive motor + impeller + terminal box/ electronics module) for replacement Power consumption (power supplied from the network) Protective Extra Low Voltage; PELV ( Protective Extra Low Voltage, formerly functional extra low voltage with safe isolation ) provides extra protection from electric shock. The voltage is so low that electrical shock currents are normally not dangerous. However, unlike SELV, active parts and components of the equipment must be earthed and connected with the protective earth conductor. Pump master computer, Wilo-specific data interface Volume flow Spare motor (drive motor + impeller + terminal box/ electronics module) for replacement Safety Extra Low Voltage; SELV (formerly safety low voltage ) is a low electrical voltage that offers special protection against electric shocks compared to electric circuits with higher voltages due to the low voltage level and the insulation. The voltage is so low that electrical shock currents are normally not dangerous. Run signal or collective run signal Fault signal or collective fault signal Analogue input for external activation of functions German Drinking Water Ordinance of 21 (valid from ) VDI guideline for preventing damage in hot-water heating installations Building automation management with pumps and accessories Water Regulations Advisory Scheme (potable water approval for Great Britain and Northern Ireland) Thermal winding contacts (in motor for monitoring the winding temperature, full motor protection through additional tripping unit) Operating mode of double pumps: Individual operation of the respective duty pump 6

5 General notes and abbreviations Abbreviation Y,. - Meaning Operating mode of double pumps: Parallel operation of both pumps Number of poles of electric motors: 2-pole motor = approx. 29 rpm at 5 Hz Number of poles of electric motors: 4-pole motor = approx. 145 rpm at 5 Hz Number of poles of electric motors: 6-pole motor = approx. 95 rpm at 5 Hz 7

6 General notes and abbreviations Material Meaning AISI Chromium steel X2Cr Chromium steel X46Cr Chromium steel X17CrNi Chromium steel X39CrMo Chromium-nickel steel X5CrNi Chromium-nickel steel X8CrNiS Chromium-nickel steel X2CrNi L Chromium-nickel steel X2CrNi L Abrasite Al Ceram Composite EN-GJL EN-GJS G-CuSn1 GfK GG GJMW GGG Inox NiAl-Bz PPO PP-GF3 PUR SiC Chromium-nickel-molybdenum steel X5CrNiMo Chromium-nickel-molybdenum steel GX5CrNiMo Chrome nickel molybdenum steel X2CrNiMo Chromium-nickel-molybdenum steel X2CrNiMoN Chromium-nickel steel with titanium addition X6CrNiTi18-1 Chromium-nickel steel with copper and niobium additions X5CrNiCuNb16-4 Chromium-nickel steel with titanium addition X6CrNiMoTi Chilled cast iron material for use in strongly abrasive fluids Light metal material (aluminium) Coating with very high adhesive strength for long-lasting corrosion protection High-strength plastic material Cast iron with lamellar graphite, also referred to as grey cast iron. The use of grey cast iron in domestic water systems is governed by the Drinking Water Directive 98/83/EC and applicable recognised technical rules and standards! Cast iron with spheroidal graphite, also referred to as spheroidal cast iron. The use of spheroidal cast iron in domestic water systems is governed by the Drinking Water Directive 98/83/EC and applicable recognised technical rules and standards! Zinc-free bronze Fibreglass plastic See EN-GJL Special cast iron: white malleable cast iron (former designation: GTW) See EN-GJS Stainless steel Nickel-aluminium bronze Trade name: Noryl, fibreglass-reinforced plastic Polypropylene, reinforced with 3% fibreglass Polyurethane Silicon carbide (225) Ti Material Meaning AISI St Wear and tear Pumps or parts of pumps are subject to wear in accordance with the state-of-the-art (DIN 3151/DIN-EN 1336). This wear may vary depending on operating parameters (temperature, pressure, speed, water conditions) and the installation/usage situation and may result in the malfunction or failure at different times of the aforementioned products/components, including their electrical/electronic circuitry. Wearing parts are all components subject to rotary or dynamic stress, including electronic components under tension, in particular: Seals (including mechanical seals), seal rings Stuffing box Bearings and shafts Impellers and pump components Wear rings and counter rings Stationary wear rings/wear plates Macerator Capacitors Relays/contactors/switches Electronic circuits, semiconductor components, etc. Pumps and continuous-flow machines (like submersible mixers and recirculation pumps), as well as their coated components (cataphoretic, 2K or Ceram coating) are subject to constant wear due to the abrasive fluid contents. For this reason the coating is also counted as a wearing part of these units! We do not accept any liability for faults or defects arising from natural wear and tear. Note In accordance with German Energy Saving Ordinance [Energieeinspar-Verordnung EnEV] as of the at boiler outputs from 25 kw, heating pumps are to be equipped with switchgears for automatic performance control or electronically controlled pumps are to be installed. In accordance with TrinkwV 21 and DIN 593-6, only circulating pumps with corrosion-resistant pump housings made of stainless steel or red brass (CC 499K) are to be utilized in secondary hot water circulation systems. Pump replacement Detailed information on the subject of Replacing heating pumps can be found in the current Wilo replacement guide for heating pumps. Wilo General Terms of Delivery and Service The latest version of our General Terms of Delivery and Service can be found on the Internet at Steel V2A Material group, e.g , V4A Material group, e.g ,

7 General notes ErP (ecological design) guideline ErP Directive (29/125/EU) In the year 25 the European Union passed the new directive 25/32/EC with requirements for the environmentally sound design of energy-using products. It has become known as the EuP or Eco-Design directive. The abbreviation EuP stands for energy using products, and it means that the directive covers all products which consume energy (apart from motor vehicles and public means of transport). On 2th November 29 it was replaced by the new directive 29/125/EC. The most important change is that the area of application was widened from energy-driven products to energyrelated products. Accordingly, it is now usually abbreviated as ErP directive. Circulation pumps of glandless design and electric motors of glanded pumps are also covered by the ErP directive. In 29 the EU Commission defined minimum efficiency requirements in two regulations. These go far beyond the requirements of the current energy efficiency requirements for glandless pumps or the current best class EFF1 for electric motors. The ordinances will be implemented in several steps in the coming years. In this way, the highly efficient individual pump series Wilo-Stratos and Wilo-Stratos PICO already meet the particularly strict requirements of the second stage of the ordinance for glandless circulation pumps which is to apply from 215 onwards. They can thus contribute to increased energy efficiency in heating systems not just from 213, but immediately! APPLIES TO EUROPEAN DIRECTIVE FOR ENERGY RELATED PRODUCTS Glandless circulation pumps: The market for glandless pumps especially will be significantly changed by this. After all, until now in many EU countries virtually all models in use have been without speed control. These have an enormous energy consumption, however. In contrast, considerable potential savings and greenhouse gas reductions can be achieved with high-efficiency pumps due to their particularly low electricity consumption. Throughout Europe, the EU Commission Directive could save about half the energy consumption of glandless circulation pumps by the third stage of implementation in 22. This amounts to the giant quantity of 23 terawatt hours of energy per year the energy production of approx. six medium-sized coal-fired power stations. Across Europe, this corresponds to a reduction of CO2 emissions of about 11 million tonnes per year.. The yardstick for determining which pump models can continue to be used in future is referred to as the energy efficiency index (EEI). This is calculated using a process defined in the ordinance (EC) 641/29. The average electrical power of pump is calculated on the basis of a load profile in relation to a reference pump, i.e. an average pump with the same hydraulic output. Three stages are planned: 1. From January 213, the Energy Efficiency Index (EEI) limit value for glandless circulating pumps installed outside the heat generator (external pumps) will be defined as.27. The previous energy efficiency classes will then no longer exist. As a rule, pumps far exceed the minimum efficiency requirements of the current energy efficiency class A. This is why the energy efficiency classes will be replaced by an EEI marking on the pump. 2. From August 215, the EEI limit value will be reduced further to.23. This will also apply to glandless circulation pumps, designed to operate in newly installed heat generators or solar thermal systems (integrated pumps). 3. In the last implementation stage, the regulations starting from 22 will also apply for the replacement of integrated pumps in existing heat generators. All glandless circulation pumps in the heating, air-conditioning and solar sectors will be affected. Secondary hot water circulation pumps are an exception to this. 9

8 General notes ErP (ecological design) guideline Glanded pumps: An appropriate EU regulation for conventional electric motors has taken effect earlier than the one planned for glandless circulation pumps. It also applies to units installed in glanded pumps for heating, air-conditioning, water supply, pressure boosting and sewage disposal. New efficiency classes have been defined against this background. EFF has become IE From 16th June 211 motorised glanded pumps may be placed on the market only if their motors demonstrate a minimum motor efficiency class of IE2. The designation IE stands for International Efficiency and defines globally applicable efficiency classes for low-voltage three-phase AC asynchronous motors in the power range from.75 to 375 kw. It is based on the new IEC 634-3:28 standard. It supersedes the division into three efficiency classes EFF1 to EFF3 which has applied in Europe since APPLIES TO EUROPEAN DIRECTIVE FOR ENERGY RELATED PRODUCTS The following motor efficiency classes have been defined: IE1 = Standard efficiency, approximately comparable to EFF2 IE2 = High efficiency, approximately comparable to EFF1 IE3 = Premium efficiency IE4 = Super-premium efficiency (IEC TS Ed.1) Three stages were defined for the conversion: 1. Efficiency level IE2 must be complied with from 16th June 211 by all new sales of electric motors on the market apart from a few design types and applications. Pump motors with the currently established efficiency level EFF2 which will be called IE1 in the future may then no longer be sold in the European Union. 2. From 1st January 215, an even stricter efficiency level IE3 will apply. By this time, motors with a rated output power of 7.5 to 375 kw must reach this level. Alternatively, they must meet efficiency level IE2 and be equipped with speed control. 3. From 1st January 217, these requirements will apply also to motors with a rated output power of.75 to 375 kw. Against this background, since 1st January 211 all glanded pumps supplied by Wilo have been already equipped with IE2 motors. Thus the requirements of the first stage of the ErP Directive have been satisfied ahead of time. The ErP Directive also applies to pressure boosting systems. Therefore for several months, Wilo has for instance been offering for pressure boosting systems the Helix range of high-pressure centrifugal pumps, which are fitted as standard with IE2 motors. Thus these pumps also already satisfy the requirements of the Directive, which come into effect from mid-211. The high-efficiency pump series Wilo-Stratos GIGA for the upper performance range in heating, cold-water and cooling applications is a completely new development. For the first time, glanded pumps are driven by EC motors with extremely low current consumption. The motor's energy efficiency is based on the new high-efficiency HED drive concept (HED High Efficiency Drive) from Wilo and even outclasses the limits of the upcoming efficiency class IE4 (acc. to IEC TS Ed.1) that is set to be the best. In addition, all specifications of the new EU Regulation, which are set to come into force on 16th June 211, 1st January 215 or 1st January 217 under the auspices of the European Ecological Design Directive on the energy efficiency of electric motors, have already been substantially exceeded. 1

9 Planning guide EEI classifications Energy efficiency class In the context of the Kyoto Agreement, European governments in particular are pursuing the goal of drastically reducing CO 2 emissions. Energy labelling, particularly for high-consumption household devices such as washing machines and refrigerators, is prescribed as an important control element for providing the end consumer with an aid for making decisions in favour of energy-saving appliances. Due to the fact that heating circulation pumps are among the biggest individual electricity consumers in household use because of their long running times, leading European heating pump manufacturers have voluntarily declared their intention of henceforth attaching energy labels to their heating pumps. This makes it possible for users and end consumers to recognise, on the basis of an already familiar classification system, whether a heating circulation pump in use is particularly energy-efficient. The classification of the energy efficiency of heating pumps is carried out by means of a technical measuring procedure, which provides the Energy Efficiency Index, EEI. The smaller the EEI, the less electrical energy the pump consumes and the more favourable the energy classification. Relative power consumption 18% 16% 14% 12% 1% 8% 6% 4% 2% % A B C D E F G Energy class Fig.: Comparison of the energy consumption rates of pumps with the same hydraulic output Energy class Energy Efficiency Index A EEI <.4 B.4 EEI <.6 C.6 EEI <.8 D.8 EEI < 1. E 1. EEI < 1.2 F 1.2 EEI < 1.4 G 1.4 EEI Table: Classification of the Energy Efficiency Index in 7 different energy categories. Fig.: Energy label for heating circulation pumps, Example: Energy class A The following tables list the corresponding energy class for all heating pumps to be labelled, which is incorporated in the energy label on the packaging. In accordance with the lettering system familiar from household appliances, A is the best possible and G is the worst possible of the energy classes. A comparison of hydraulically similar pumps with different energy classifications reveals that there is a difference of approximately 22% in terms of energy consumption between two sequentially numbered energy classes. Accordingly, an energy class A pump requires on average only around 33% of the electrical energy consumed by a class D pump. Even though the energy requirements of a class A pump are very high, high-efficiency energy class A pumps have in the meantime become available for use throughout the entire performance range from single-family houses to large buildings. 11

10 Planning guide Variant key, pump control Variant key for glanded pumps valid for variants of the following series: IPL, DPL, IL, DL, IPS, BL, IP-E, DP-E, IL-E, DL-E Variants Key Meaning Mechanical seal variants S1 Q1Q1X4GG for water-glycol mixtures with the following compositions: Glycol proportion of 2 to 4 vol.% and an operating temperature of 4 C to 12 C or glycol proportion > 4 to 5 vol.% and an operating temperature of -2 C to 12 C (see page 14) Housing variants Motor variants S2 AQ1VGG water-oil emulsions and water with oil components up to 9 C (see page 14) H1 H4 H5 K3 N EN-GJS-4-18-LT (formerly GGG 4.3) (shot graphite casting or spheroidal cast iron) Combination flanges PN6/PN1 for IPL; only for IPL 4, IPL 5 (145 rpm), IPL 4, IPL 5, IPL 65 (29 rpm) Max. operating pressure PN 16 (for IPL/DPL and IP_E/DP-E) Integrated PTC thermistors (3 x, tripping units as accessories) Version N with IEC standard motor (only IPL, DPL) Impeller variants L1 Impeller made of red brass RG = G-CuSn 1 Control variants R1 Electronically controlled pump without sensor (DDG) Pump control When Wilo pumps are operated with control devices or module accessories, the electrical operating conditions are to be complied with in accordance with VDE 16. When operating glandless and glanded pumps with brands of frequency converters other than those supplied by Wilo, output filters for reducing motor noise and for preventing harmful voltage peaks are to be used and the following limit values are to be complied with: Glandless pumps with P kw and glanded pumps with P kw rate of voltage rise du/dt < 5 V/μs voltage peaks û < 65 V For the noise reduction of glandless pump motors, it is recommended that sine filters (LC filters) are used rather than du/dt filters (RC filters). Glanded pumps with P 2 > 1.1 kw rate of voltage rise du/dt < 5 V/μs voltage peaks û < 85 V 12

11 Glandless premium high-efficiency pumps Wilo-Stratos PICO H[m] 6 5 Wilo-Stratos PICO >Accessories Page Screwed connections Adapter fittings , 25, 3/1-6 15, 25, 3/ Q[m³/ h] APPLIES TO EUROPEAN DIRECTIVE FOR ENERGY RELATED PRODUCTS TÜV certificate can be found at Construction Glandless circulation pump with threaded connection, blocking-current proof EC motor and integrated electronic performance control. Application All hot water heating systems, air-conditioning applications, industrial circulation systems. Technical data Fluid temperature +2 C to +11 C Mains connection 1~23 V, 5 Hz Protection class IP X4D Threaded connection Rp ½, Rp 1 and Rp 1¼ Max. operating pressure 1 bar Wilo-Stratos PICO Special features/product advantages Energy efficiency class A Maximum efficiency thanks to ECM technology High-efficiency pump especially for the single and two-family house and two to sixfamily house. Up to 9% electricity savings compared to old uncontrolled heating pumps Only 3 watts min. power consumption Pre-selectable control modes for optimum load adaption Δp-c (constant differential pressure), Δp-v (variable differential pressure) can be combined with the Dynamic Adapt control function (available from January 212) Automatic setback operation Integrated motor protection LC display displaying the current consumption in watts and the cumulative kilowatt hours Reset function for resetting the electricity meter or for resetting the settings to the factory settings (available from January 212) Ventilation routine for automaticventing of the rotor chamber Quick electrical connection with Wilo- Connector Very high starting torque for reliable starting Price group: W1 Type Pipe connection EEI Class Overall length Rated pressure Mains connection Gross weight Pieces per pallet Rp l PN m mm bar kg ] GBP Stratos PICO 25/1-4 1 A ~23 V, 5/6 Hz L 217. Stratos PICO 25/1-6 1 A ~23 V, 5/6 Hz L 219. Stratos PICO 25/ A ~23 V, 5/6 Hz L 26. Stratos PICO 25/ A ~23 V, 5/6 Hz L 213. Stratos PICO 3/1-4 1¼ A ~23 V, 5/6 Hz L 224. Stratos PICO 3/1-6 1¼ A ~23 V, 5/6 Hz L 226. Art no. 13

12 Glandless standard high-efficiency pumps Wilo-Yonos PICO H/m Wilo-Yonos PICO >Accessories Page Screwed connections Adapter fittings , 25, 3/1-4 15, 25, 3/1-6 Coming soon!,5 1, 1,5 2, 2,5 3, 3,5Q/m³/h APPLIES TO EUROPEAN DIRECTIVE FOR ENERGY RELATED PRODUCTS Construction Glandless circulation pump with threaded connection, blocking-current proof EC motor and integrated electronic performance control. Application All hot water heating systems, air-conditioning applications, industrial circulation systems. Technical data Fluid temperature -1 C to +95 C Mains connection 1~23 V, 5 Hz Wilo-Yonos PICO Protection class IP X2 D Threaded connection Rp ½, Rp 1 and Rp 1¼ Max. operating pressure 6 bar Special features/product advantages Energy efficiency class A Highest degrees of efficiency due to ECM technology High-efficiency pump especially for single and two-family houses, as well as for two to six-family houses Only 4 watts min. power consumption Pre-selectable control modes for optimum load adaptation >p-c (constant differential pressure), >p-v (variable differential pressure), Integrated motor protection LED display to adjust the setpoint and to show the current consumption in watts Ventilation function to vent the rotor chamber Quick electrical connection with Wilo-Connector Flexible installation due to compact design Very high starting torque for reliable starting Price group: W1 Type Pipe connection EEI Class Overall length Rated pressure Mains connection Gross weight Pieces per pallet Art no. Rp l PN m mm bar kg Yonos PICO 15/ ½ A ~23 V, 5/6 Hz Yonos PICO 15/ ½ A ~23 V, 5/6 Hz Yonos PICO 25/1-4 1 A ~23 V, 5/6 Hz Yonos PICO 25/ A ~23 V, 5/6 Hz Yonos PICO 25/1-6 1 A ~23 V, 5/6 Hz Yonos PICO 25/ A ~23 V, 5/6 Hz Yonos PICO 3/1-4 1¼ A ~23 V, 5/6 Hz Yonos PICO 3/1-6 1¼ A ~23 V, 5/6 Hz

13 Glandless standard high-efficiency pumps Wilo-Stratos ECO...-BMS H[m] , 3/1-5 Wilo-Stratos ECO-BMS >Accessories Page Screwed connections Adapter fittings ,5 1, 1,5 2, 2,5Q[m³/h] Construction Glandless circulation pump with threaded connection, EC motor with automatic power adjustment Application Hot-water heating systems of all kinds, industrial circulation systems Technical data Fluid temperature +15 C to +11 C (at max. ambient temperature +25 C) Mains connection 1~23 V, 5 Hz Wilo-Stratos ECO...-BMS Protection class IP 44 Threaded connection Rp 1 and Rp 1¼ Max. operating pressure 1 bar Special features/product advantages Energy efficiency class A Up to 8% electricity savings compared to uncontrolled circulation pumps High-efficiency pump especially for single and two-family houses, as well as for two to six-family houses Maximum efficiency thanks to ECM technology Very high starting torque for reliable starting Quick connection with spring clips BA connection: For connection to external monitoring units (e.g. building automation) Collective fault signal as potential-free contact, control input External Off, control input -1 V Only 5.8 W min. power consumption Standard thermal insulation for heating applications Price group: W1 Type Pipe connection EEI Class Overall length Rated pressure Mains connection Gross weight Pieces per pallet Rp l PN m mm bar kg ] GBP Stratos ECO 25/1-5-BMS 1 A ~23 V, 5 Hz L 351. Stratos ECO 3/1-5-BMS 1¼ A ~23 V, 5 Hz L 355. Art no. 15

14 Glandless premium high-efficiency pumps Wilo-Stratos H[m] (3,32,4,5)/1-1 25(3)/1-8 32/1-12 4/1-12 5/ /1-12 Wilo-Stratos 8(1)/1-12 >Accessories Page IR-Module, IR-Monitor 122 Screwed connections 124 Adapter fittings 127 IF-Modules (3)/1-6 3/1-12 4(5)/1-8 5/1-9 65/1-9 25(3)/ / Q[m³/h] APPLIES TO EUROPEAN DIRECTIVE FOR ENERGY RELATED PRODUCTS TÜV certificate can be found at Construction Glandless circulation pump with threaded connection or flange connection, EC motor with automatic power adjustment. Application Hot-water heating systems of all kinds, airconditioning systems, closed cooling circuits, industrial circulation systems. Technical data Permissible temperature range -1 C to +11 C Mains connection 1~23 V, 5/6 Hz Protection class IP X4D Wilo-Stratos Screwed connection or flange connection (depending on type) Rp 1 to DN 1 Max. operating pressure, standard version: 6/1 bar or 6 bar (special version: 1 bar or 16 bar) Special features/product advantages Energy efficiency class A Highest degrees of efficiency due to ECM technology Up to 8% electricity savings compared to uncontrolled circulation pumps Front operation and access to the terminal space, variable installation positions, display independent of position Simple installation due to combination flanges PN 6/PN 1 (with DN 32 to DN 65) Can be used in cooling/air-conditioning systems without ambient temperature limits Pump housing with cataphoretic coating for the prevention of corrosion by condensation formation System expansion by means of retrofittable interface modules for communication: Modbus, BACnet, CAN, LON, PLR etc. Remote operation via infrared interface (IR- Module/IR-Stick/IR-Monitor) Options Special versions for operating pressure PN 16 (at additional charge) Price group: W1 Type Pipe connection Overall length EEI Class Rated pressure Mains connection Gross weight Rp l PN m mm bar kg ] GBP Stratos 25/ A 1 1~23 V, 5/6 Hz L 462. Stratos 25/ A 1 1~23 V, 5/6 Hz L 5. Stratos 25/ A 1 1~23 V, 5/6 Hz L 524. Stratos 25/ A 1 1~23 V, 5/6 Hz L 53. Stratos 3/1-4 1¼ 18 A 1 1~23 V, 5/6 Hz L 498. Stratos 3/1-6 1¼ 18 A 1 1~23 V, 5/6 Hz L 52. Stratos 3/1-8 1¼ 18 A 1 1~23 V, 5/6 Hz L 556. Stratos 3/1-1 1¼ 18 A 1 1~23 V, 5/6 Hz L 58. Stratos 3/1-12 1¼ 18 A 1 1~23 V, 5/6 Hz L 793. Art no. 16

15 Glandless premium high-efficiency pumps Wilo-Stratos Wilo-Stratos Price group: W1 Type Nominal flange diameter Overall length EEI Class Rated pressure Mains connection Gross weight DN l PN m mm bar kg ] GBP Stratos 32/ A 6/1 1~23 V, 5/6 Hz L 62. Stratos 32/ A 6/1 1~23 V, 5/6 Hz L 895. Stratos 4/ A 6/1 1~23 V, 5/6 Hz L 735. Stratos 4/ A 6/1 1~23 V, 5/6 Hz L 92. Stratos 4/ A 6/1 1~23 V, 5/6 Hz L 684. Stratos 4/ A 6/1 1~23 V, 5/6 Hz L Stratos 5/ A 6/1 1~23 V, 5/6 Hz L Stratos 5/ A 6/1 1~23 V, 5/6 Hz L Stratos 5/ A 6/1 1~23 V, 5/6 Hz L 775. Stratos 5/ A 6/1 1~23 V, 5/6 Hz L 1 6. Stratos 65/ A 6/1 1~23 V, 5/6 Hz L Stratos 65/ A 6/1 1~23 V, 5/6 Hz L Stratos 8/ A 6 1~23 V, 5/6 Hz L Stratos 8/ A 1 1~23 V, 5/6 Hz L Stratos 1/ A 6 1~23 V, 5/6 Hz L Stratos 1/ A 1 1~23 V, 5/6 Hz L Art no. 17

16 Glandless premium high-efficiency pumps Wilo-Stratos-D H[m] /1-12 4/1-12 4(5)/1-8 5/1-12 5/1-9 Wilo-Stratos-D + 8/1-12 >Accessories Page IR-Module, IR-Monitor Screwed connections Adapter fittings IF-Modules / / Q[m³/h] Construction Glandless double circulation pump with flange connection, EC motor with automatic power adjustment Application Hot-water heating systems of all kinds, airconditioning systems, closed cooling circuits, industrial circulation systems Technical data Permissible temperature range -1 C to +11 C Mains connection 1~23 V, 5/6 Hz Protection class IP X4D Flange connection DN 32 to DN 8 Wilo-Stratos-D with BUS interface CAN Max. operating pressure, standard version: 6/1 bar or 6 bar (special version: 1 bar or 16 bar) Special features/product advantages Energy efficiency class A Highest degrees of efficiency due to ECM technology Up to 8% electricity savings compared to uncontrolled circulation pumps Front operation and access to the terminal space, variable installation positions, display independent of position Simple installation due to combination flanges PN 6/PN 1 (with DN 32 to DN 65) Can be used in cooling/air-conditioning systems without ambient temperature limits Pump housing with cataphoretic (cataphoretic) coating for the prevention of corrosion by condensation formation System expansion by means of retrofittable interface modules for communication: Modbus, BACnet, LON, CAN, PLR etc. Remote operation via infrared interface (IR- Module/IR-Stick/IR-Monitor) Integratable dual pump management due to retrofit Stratos IF-Modules: - Main/standby mode with fault-dependent switchover - Efficiency-optimised peak-load operation Options Special versions for operating pressure PN 16 (at additional charge) Price group: W1 Type Nominal flange diameter Overall length EEI Class Rated pressure Mains connection Gross weight DN l PN m mm bar kg ] GBP Stratos-D 32/ A 6/1 1~23 V, 5/6 Hz L Stratos-D 32/ A 6/1 1~23 V, 5/6 Hz L Stratos-D 4/ A 6/1 1~23 V, 5/6 Hz L Stratos-D 4/ A 6/1 1~23 V, 5/6 Hz L Stratos-D 5/ A 6/1 1~23 V, 5/6 Hz L Stratos-D 5/ A 6/1 1~23 V, 5/6 Hz L Stratos-D 5/ A 6/1 1~23 V, 5/6 Hz L Stratos-D 65/ A 6/1 1~23 V, 5/6 Hz L Stratos-D 8/ A 6 1~23 V, 5/6 Hz L Stratos-D 8/ A 1 1~23 V, 5/6 Hz L Art no. 18

17 Glandless automatic pumps Wilo-Smart H[m] 4 3 Wilo-Smart >Accessories Page Screwed connections Adapter fittings Thermal insulation shells Smart 15/6, 25/6, 25/6-RG, 3/6 Smart 15/4, 25/4-RG Smart-A 25/4, 3/4 2 1,5 1 1,5 2 2,5 3 Q[m³/h] Construction Glandless circulating pump with screwed connection and automatic power adjustment Application Hot-water heating systems of all kinds, industrial circulation systems Technical data Permissible temperature range +2 C to +95 C Mains connection 1~23 V, 5 Hz Protection class IP 42 Threaded connection Rp ½, 1, 1 ¼ Max. operating pressure 1 bar Wilo-Smart Special features/product advantages Energy efficiency class A (Smart A 25/4, 3/4) Up to 7% electricity cost savings compared to uncontrolled heating pumps Simple pipe connection due to the safe and practical wrench attachment point on the pump body. Safe electrical connection due to ergonomically optimised terminal box. Quick connection with spring clips. Simple operation. Factory setting suitable for 8% of all heating system requirements. Simple selection of the three pre-programmed control channels with the red button. The automatic controller of the Wilo-Smart prevents flow noise in the heating system and reduces electricity consumption. Operational reliability due to automatic deblocking function. A special bronze filter prevents particles from penetrating the motor compartment. Price group: W Type Pipe connection Overall length Rated pressure EEI Class Mains connection Gross weight Rp l PN m mm bar kg ] GBP Smart A 25/ A 1~23 V, 5 Hz L 65. Smart B B 1~23 V, 5 Hz L 68. Pieces per pallet Art no. 19

18 Glandless standard pumps Wilo-Star-RS H[m] Star-RS 15/6, 25/6, 3/6 Star-RS 15/4, 25/4, 3/4 Star-RS 25/2, 3/2 Star-RS 25/8, 3/8 Star-RS 25/7, 3/7 Wilo-Star-RS Q[m³/h] >Accessories Page Screwed connections Adapter fittings Thermal insulation shells Construction Glandless circulation pump with threaded connection. Preselectable speed stages for power adjustment Application Hot-water heating systems of all kinds, industrial circulation systems, cold water systems and air-conditioning systems Wilo-Star-RS Technical data Permissible temperature range -1 C to +11 C Mains connection 1~23 V, 5 Hz Protection class IP 44 Threaded connection Rp ½, Rp 1 or Rp 1¼ Max. operating pressure 1 bar Special features/product advantages Suitable for any installation position with horizontal shaft; terminal box in o'clock position Three preselectable speed stages for load adjustment Easy and safe installation due to practical wrench attachment point on pump body Simplified electrical installation due to terminal box with removable threaded cable connection that can be used on both sides; Quick connection with spring clips Price group: W Type Pipe connection EEI Class Overall length Rated pressure Mains connection Gross weight Pieces per pallet Rp l PN m mm bar kg ] GBP Star-RS 15/4 ½ B ~23 V, 5 Hz L 88. Star-RS 15/6 ½ C ~23 V, 5 Hz L 17. Star-RS 25/2 1 C ~23 V, 5 Hz L 143. Star-RS 25/4 1 B ~23 V, 5 Hz L 144. Star-RS 25/6 1 C ~23 V, 5 Hz L 147. Star-RS 3/2 1¼ C ~23 V, 5 Hz L 148. Star-RS 3/4 1¼ B ~23 V, 5 Hz L 15. Star-RS 3/6 1¼ C ~23 V, 5 Hz L 176. Art no. 2

19 Glandless standard pumps Wilo-Star-RSD H[m] 5 4 Wilo-Star-RSD >Accessories Page + Screwed connections Adapter fittings Star-RSD 3/6 3 Star-RSD 3/ Q[m³/h] Construction Glandless circulation double pump with threaded connection; Preselectable speed stages for power adjustment Application Hot-water heating systems of all kinds, industrial circulating systems, cold-water systems and air-conditioning systems Wilo-Star-RSD Technical data Permissible temperature range -1 C to +11 C Mains connection 1~23 V, 5 Hz Protection class IP 44 Threaded connection Rp 1¼ Max. operating pressure 1 bar Special features/product advantages Double pump for single or parallel operation Suitable for any installation position with horizontal shaft; terminal box in o'clock position Increased reliability in individual operation due to the constant availability of a standby unit ready for operation Price group: W Type Pipe connection Overall length EEI Class Rated pressure Mains connection Gross weight Rp l PN m mm bar kg ] GBP Star-RSD 3/4 1¼ 18 D 1 1~23 V, 5 Hz L 367. Star-RSD 3/6 1¼ 18 D 1 1~23 V, 5 Hz L 387. Art no. 21

20 Glandless standard pumps Wilo-TOP-S H[m] /13 25(3)/5 25(3)/1 25(3)/7 3/4 5/15 4/15 4/1 1 4/7 4/4 5/4 65/13 2 5/1 65/7 5/7 65/1 3 65/15 4 8/7 8/1 1/1 5 6 Wilo-TOP-S >Accessories Page Switching plugs Screwed connections Adapter fittings Wilo tripping units SK 62N/SK 622N Wilo-Protect Module-C /15 8/2 Q[m³/h] Construction Glandless circulation pump with screwed connection or flange connection. Application Hot-water heating systems of all kinds, industrial circulation systems, air-conditioning systems and closed cooling circuits Technical data Permitted temperature range -2 C to +13 C, for short periods (2 h) up to +14 C (TOP-S 25/13, 8/15, 8/2 and pumps with Wilo-Protect-Module: -2 C to +11 C) Wilo-TOP-S Mains connection: - 1~23 V, 5 Hz (depending on type) - 3~23 V, 5 Hz (with optional switching plug) - 3~4 V, 5 Hz Protection class IP X4D Screwed connection or flange connection (depending on type) Rp 1 to DN 1 Max. operating pressure, standard version: 6/1 bar or 6 bar (special version: 1 bar or 16 bar) Special features/product advantages Can be used in heating systems and in cooling/air-conditioning systems from -2 C to +13 C (TOP-S 25/13, TOP-S 8/15 and TOP-S 8/2 from -2 C to +11 C) Pump housing with cataphoretic coating for the prevention of corrosion by condensation formation Manual power adjustment with 3 speed stages Simple installation due to combination flange PN 6/PN 1 (for DN 4 to DN 65) Options Special version for operating pressure PN 16 (at additional charge) Version for special voltages on request. Price group: W2 Type Pipe connection Overall length EEI Class Rated pressure Mains connection Gross weight Rp l PN m mm bar kg ] GBP TOP-S 25/ D 1 1~23 V, 5 Hz L 259. TOP-S 25/ D 1 3~4/23 V, 5 Hz L 286. TOP-S 25/ D 1 1~23 V, 5 Hz L 32. TOP-S 25/ D 1 3~4/23 V, 5 Hz L 334. TOP-S 25/ D 1 1~23 V, 5 Hz C 367. TOP-S 25/ D 1 3~4/23 V, 5 Hz C 38. TOP-S 25/ F 1 1~23 V, 5 Hz C 395. TOP-S 25/ F 1 3~4/23 V, 5 Hz C 412. TOP-S 3/4 1¼ 18 D 1 1~23 V, 5 Hz L 276. TOP-S 3/4 1¼ 18 D 1 3~4/23 V, 5 Hz L 289. TOP-S 3/5 1¼ 18 D 1 1~23 V, 5 Hz L 281. TOP-S 3/5 1¼ 18 D 1 3~4/23 V, 5 Hz L 313. TOP-S 3/7 1¼ 18 D 1 1~23 V, 5 Hz L 34. TOP-S 3/7 1¼ 18 D 1 3~4/23 V, 5 Hz L 342. TOP-S 3/1 1¼ 18 D 1 1~23 V, 5 Hz L 47. TOP-S 3/1 1¼ 18 D 1 3~4/23 V, 5 Hz L 478. Art no. 22

21 Glandless standard pumps Wilo-TOP-S Wilo-TOP-S Price group: W2 Type Nominal flange diameter Overall length EEI Class Rated pressure Mains connection Gross weight DN l PN m mm bar kg ] GBP TOP-S 4/ D 6/1 1~23 V, 5 Hz L 57. TOP-S 4/ D 6/1 3~4/23 V, 5 Hz L 59. TOP-S 4/ D 6/1 1~23 V, 5 Hz L 652. TOP-S 4/ C 6/1 3~4/23 V, 5 Hz L 655. TOP-S 4/ D 6/1 1~23 V, 5 Hz L 798. TOP-S 4/ C 6/1 3~4/23 V, 5 Hz L 752. TOP-S 4/ D 6/1 1~23 V, 5 Hz L 93. TOP-S 4/ D 6/1 3~4/23 V, 5 Hz L 835. TOP-S 5/ D 6/1 1~23 V, 5 Hz L 731. TOP-S 5/ D 6/1 3~4/23 V, 5 Hz L 734. TOP-S 5/ C 6/1 1~23 V, 5 Hz L 877. TOP-S 5/ C 6/1 3~4/23 V, 5 Hz L 766. TOP-S 5/ C 6/1 1~23 V, 5 Hz L 976. TOP-S 5/ C 6/1 3~4/23 V, 5 Hz L 878. TOP-S 5/ C 6/1 3~4/23 V, 5 Hz L TOP-S 65/ C 6/1 1~23 V, 5 Hz L TOP-S 65/ C 6/1 3~4/23 V, 5 Hz L 914. TOP-S 65/ C 6/1 1~23 V, 5 Hz L TOP-S 65/ C 6/1 3~4/23 V, 5 Hz L 958. TOP-S 65/ C 6/1 3~4/23 V, 5 Hz L TOP-S 65/ C 6/1 3~4/23 V, 5 Hz L TOP-S 8/ C 6 1~23 V, 5 Hz L TOP-S 8/ C 6 3~4/23 V, 5 Hz L TOP-S 8/ C 1 3~4/23 V, 5 Hz L TOP-S 8/ C 6 3~4/23 V, 5 Hz L TOP-S 8/ C 1 3~4/23 V, 5 Hz L TOP-S 8/ C 6 3~4 V, 5 Hz L TOP-S 8/ C 1 3~4 V, 5 Hz L TOP-S 8/ C 6 3~4 V, 5 Hz L TOP-S 8/ C 1 3~4 V, 5 Hz L TOP-S 1/ C 6 3~4/23 V, 5 Hz L TOP-S 1/ C 1 3~4/23 V, 5 Hz L Art no. 23

22 Glandless standard pumps Wilo-TOP-SD H[m] /5 32/7 32/ /3 4/15 4/7 4/1 5/7 65/1 5/1 5/15 65/13 65/15 Wilo-TOP-SD + 8/1 8/15 8/ Q[m³/h] >Accessories Page Switching plugs Brackets for pump fixation Screwed connections Adapter fittings Wilo tripping units SK 62N/SK 622N Wilo-Protect Module-C Blind plates Construction Glandless double circulation pump with flange connection (TOP-SD 3/5 with screwed connection). Application Hot-water heating systems of all kinds, industrial circulation systems, air-conditioning systems and closed cooling circuits Technical data Permitted temperature range -2 C to +13 C, for short periods (2 h) to +14 C (TOP-SD 8/15, TOP-SD 8/2 and pumps with Wilo- Protect-Module: -2 C to +11 C) Wilo-TOP-SD Mains connection: - 1~23 V, 5 Hz (depending on type) - 3~23 V, 5 Hz (with optional switching plug) - 3~4 V, 5 Hz Protection class IP X4D Screwed connection or flange connection (depending on type) Rp 1¼ to DN 8 Max. operating pressure, standard version: 6/1 bar or 6 bar (special version: 1 bar or 16 bar) Special features/product advantages Can be used in heating systems and in cooling/air-conditioning systems from -2 C to +13 C (TOP-SD 8/15 and TOP-SD 8/2 from - 2 C to +11 C) Double pump for main/standby mode or parallel operation Manual power adjustment with 3 speed stages Pump housing with cataphoretic coating for the prevention of corrosion by condensation formation Simple installation due to combination flange PN 6/PN 1 (for DN 32 to DN 65) Options Special versions for operating pressure PN 16 (at additional charge) Versions for special voltages on request Price group: W2 Type Pipe connection Overall length EEI Class Rated pressure Mains connection Gross weight Rp l PN m mm bar kg ] GBP TOP-SD 3/5 1¼ 18 D 1 1~23 V, 5 Hz L 587. TOP-SD 3/5 1¼ 18 D 1 3~4/23 V, 5 Hz L 65. Art no. Wilo-TOP-SD Price group: W2 Type Nominal flange diameter Overall length EEI Class Rated pressure Mains connection Gross weight DN l PN m mm bar kg ] GBP TOP-SD 32/ E 6/1 1~23 V, 5 Hz L 817. TOP-SD 32/ D 6/1 3~4/23 V, 5 Hz L 841. TOP-SD 32/ D 6/1 1~23 V, 5 Hz L 86. TOP-SD 32/ D 6/1 3~4/23 V, 5 Hz L 945. TOP-SD 4/ E 6/1 1~23 V, 5 Hz L TOP-SD 4/ D 6/1 3~4/23 V, 5 Hz L 1 2. TOP-SD 4/ D 6/1 1~23 V, 5 Hz L TOP-SD 4/ D 6/1 3~4/23 V, 5 Hz L TOP-SD 4/ D 6/1 1~23 V, 5 Hz L Art no. 24

23 Glandless standard pumps Wilo-TOP-SD Wilo-TOP-SD Price group: W2 Type Nominal flange diameter Overall length EEI Class Rated pressure Mains connection Gross weight TOP-SD 4/ C 6/1 3~4/23 V, 5 Hz L TOP-SD 4/ E 6/1 1~23 V, 5 Hz L TOP-SD 4/ D 6/1 3~4/23 V, 5 Hz L TOP-SD 5/ D 6/1 1~23 V, 5 Hz L TOP-SD 5/ C 6/1 3~4/23 V, 5 Hz L TOP-SD 5/ D 6/1 1~23 V, 5 Hz L 2 8. TOP-SD 5/ D 6/1 3~4/23 V, 5 Hz L TOP-SD 5/ D 6/1 3~4/23 V, 5 Hz L TOP-SD 65/ D 6/1 1~23 V, 5 Hz L TOP-SD 65/ D 6/1 3~4/23 V, 5 Hz L TOP-SD 65/ D 6/1 3~4/23 V, 5 Hz L TOP-SD 65/ D 6/1 3~4/23 V, 5 Hz L TOP-SD 8/ D 6 1~23 V, 5 Hz L TOP-SD 8/ D 6 3~4/23 V, 5 Hz L TOP-SD 8/ D 1 3~4/23 V, 5 Hz L TOP-SD 8/ C 6 3~4 V, 5 Hz L TOP-SD 8/ C 1 3~4 V, 5 Hz L TOP-SD 8/ C 6 3~4 V, 5 Hz L TOP-SD 8/ C 1 3~4 V, 5 Hz L Art no. DN l PN m mm bar kg ] GBP 25