ENGINE SERVICE TOOL. Engine Service Tool Under Car Service Tool Electrical Service Tool 58-66

Transcription

1

2 Engine Service Tool 1-31 ENGINE SERVICE TOOL Under Car Service Tool EN0004 Doughnut Stretcher EN0137 4PC Diesel Injector Socket Set Electrical Service Tool Brake Service Tool Body Service Tool Battery Service Tool 84 Air Conditional Service Tool Cooling System Service Tool Diagnostic Service Tool One end features an offset hook. For easy removal, use to grab onto the rubber mounting rings or doughnuts used in many exhaust systems for easy removal. EN0132 Honda & Acura Crankshaft and Harmonic Balancer Holder For use on ALFA ROMEO, CHRYSLER, BMW, FORD,VW, MERCEDES, AUDI, OPEL, VAUXHALL, SEAT, VOLVO, ROVER also on VOLVO, MAN 2.5TD & SCANIA HGVS. 1PC Injector socket 6PT x 22mm x 110mm(L). 1PC Injector socket 12PT x 22mm x 75mm(L). 1PC Injector socket 12PT x 27mm x 78mm(L). 1PC Injector socket 12PT x 28mm x 78mm(L). EN0144 Honda Crankshaft Pulley Holder Kit Benz And Bmw Service Tool Motorcycle Service Tool Truck Service Tool Timing Service Tool General Tool Gear Puller And Specialty Puller Lubricating And Oil Filter Tool Allows the crankshaft pulley and/or harmonic balancer bolt to be broken loose. Includes tool necessary to properly counter the rotation of the crankshaft pulley/harmonic balancer during removal and reinstallation of crank bolt. Secures the pulley in place not allowing it to rotate during removal and reinstallation of crank bolt. Specially designed to work on 1990 and newer Honda and Acura models and Honda civic 1980 and newer models. EN0133 Honda And Acura Harmonic Damper Pulley Holding Tool (50mm) Allows the crank shaft pulley and harmonic balancer bolt to be broken loose. Secures the pulley in place not allowing it to rotate during removal and reinstallation of crank bolt. Specially designed to work on 1990 and newer Honda and Acura models. EN0227 Crank Seal Remover and Installer Kit Hand Tool Pliers And Plastic Cutter Pneumatic Tool Specialty Socket & Socket Set Wrench And Spanner Tool This unique 50mm tool has been developed to aid in the removal and installation of the crank bolt on most Honda and Acura In operation with the use of a 1/2 breaker bar or ratchet this tool holds the harmonic damper pulley from rotating when removing the pulley bolt. There is a hole in the center of the tool to allow the use of a socket and extension bar to break loose or tighten the pulley bolt. Allows the crank seal to be replaced without dismantling the crank case saving your time and costs. Universal use covering a wide range of cars with oil seals between 27mm and 58mm in diameter. Use the existing bolt in the vehicle for installation. Screw type adapter to fit centering. The blue seal adapters are made of aluminum to prevent the damage of crank. EN-1

3 EN0237 Assembling And Disassembly Of Self Adjusting Clutches Master Kit EN0208 Oil Pan Repair Master Set EN0228 Universal Valve Spring Compressor Tool EN0234 Engine Calibration and Set up Kit Directions Suitable for most Self Adjusting Clutches SAC (3 and 4 holes) equipped on vehicles of FIAT GROUP, VW-AUDI, BMW, MERCEDES, VOLVO, OPEL, RENAULT etc. Allows operations on clutch equipped with this device in order to prevent any damage to system and to keep adapter ring in right position. Advantages: Pre-tightening of disk pushing plate during assembly and disassembly avoiding clutch deformation. Alignment of clutch disk to drive bearing or to disk pushing plate. EN0177 2PCS Lambda Sensor Socket Thread Chaser Used for repairing and cleaning damaged threads on lambda sensor ports. Size: 1PC 12mm x P PC 18mm x P1.5 EN0259 Universal Clutch Aligning Tool Feature: Solid and fast solution for the repair of defective oil drain screw thread without the expensive replacement of the sump. Application: The damaged thread is simply to tap away to the next size expands. Oil drain screw in part with Allen drive for oil pans with recessed drain opening suitable. Universal applications e.g. for: Audi, BMW, Citroen, Daimler- Benz, Ford, Fiat, Honda, Mazda, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Saab, Seat, Skoda, Toyota, Volvo, VW etc. Scope of supply: complete with 1 / 3 foam insert in the plastic case. Replacement oil drain screw and aluminum seals are available. Consisting of: 1 PC Special Taps M13x1.5 1 PC Special Taps M15x1.5 1 PC Special Taps M17x1.5 1 PC Special Taps M20x1.5 5 PCS Oil drain plug gasket with aluminum M13x1.5 external drive 6-kant SW17 5 PCS Oil drain plug gasket with aluminum M15x1.5 external drive 6-kant SW19 5 PCS Oil drain plug gasket with aluminum M17x1.5 inner drive 6-kant SW 8 5 PCS Oil drain plug gasket with aluminum M20x1.5 inner drive 6-kant SW 10 Suitable for replacement of valve springs and valve stem oil seals without the need to remove the cylinder head. Application: Opel / BMW / Seat / VW / Audi / Hyundai / Toyota / Ford / Renault 19 and Clio. EN0231 Damper Pulley Holder Wrench Set 1 PC 13 mm box style pulley holder wrench. 1 PC 15 mm box style pulley holder wrench. 1 PC 16 mm box style pulley holder wrench. 1 PC 17 mm box style pulley holder wrench. 1 PC 19 mm box style pulley holder wrench. EN0245 9PCS Pre-Heater Plug Puller Set The sliding indicator to display the piston movement. Use on the Hemi-type engines, easily find the TDC compression stroke. Set included 12mm and 18mm spark plug adapters. EN0171 Valve Spring Compressor Repair Kit Completes service tool kit for OHV & OHC petrol or diesel Use on AUDI, NISSAN, TOYOTA, CHRYSLER, HONDA, MAZDA, MITSUBISHI, PORSCHE, VOLVO, VW. EN PCS Alternator Freewheel Pulley Removal Tool EN0220 Fuel Line Connectors Pliers 2 PCS Reamer to ream out and clean the bore between the glow plug and combustion chambers. Suitable for Mercedes CDI engines 4,5&6 cylinder, OM611, 612, 613 with glow plug threads M10 x 1.0 and 4valve engines OM604, Om605, OM606 with glow plug thread size M12x PC puller for pulling out pre-heater plugs with 10mm across flats on Mercedes CDU 6 PCS 3/8 Dr. Universal joint glow plug socket Size: 8,9,10,12,14,16mm, length 160mm Material: CR-V. Special design aligns and assembles clutch on the workbench for easy installation. Suited for front wheel drivers that have no pilot bearing in flywheel. Designed for most vehicles up to 5 tons with single plate clutches. Use for VW-AUDI, FIAT, GM, OPEL MERCEDES etc, E.G. MERCEDES M-CLASS with petrol For removal and replacement of the connections on the in-line fuel filter. Required when replacing the fuel filter or during engine repairs. H10, H8, T50, T40, M10, M8, M10 Spline x 1/2 Dr for Bosch Alternators with freewheel pulleys. 1/2 Dr. to hex adapter, T50 star x 1/2 Dr. 2 PCS Pulley connectors. 2 PCS Further adapters. EN-2 EN-3

4 EN0135 Camshaft Drive Belt Pulley Puller EN0242 Hydraulic Valve Lifter Puller EN0107 PSA Exhaust Pipe Clamp Pliers EN0112 Diesel Injector Puller Special puller designed for pulling camshaft pulley wheels on 4 & 6 cylinder, V6 & V8 engines on VW and AUDI petrol engine. EN0244 Clutch Centering Mandrels Large pump remover & sprocket retaining tools for injection pump removal on BMW models with M74/M47TU and M57/ M57TU2 2.0 & 3.0 diesel Small pump remover & sprocket retaining tool for injection pump removal on Land Rover Freelander and Rover 75 models with TD4 and M Special design to hold opening the spring clamp and replace the exhaust. Total length: 300mm. Maximum jaws opening: 60mm. EN0110 VW, AUDI Belt Pulley Holder Assists removal of stubborn BOSCH and LUCAS diesel injectors-saves time and money when injectors are difficult to remove. With M8, M12, M14 adaptors. EN0115 4PCS Sensor & Sending Unit Socket Extension Set EN0260 Diesel Injector Puller Set For fast and exact clutch plate centering on vehicles with clutch guide bearing. For passenger cars and small commercial vehicles. Ø 20mm ~ 26.6mm Ø15mm ~ 19mm EN0113 Ribbed Drive Pulleys Puller Suitable for the removal of stubborn Bosch / Delphi diesel injectors. Set included 6 adaptors for different removal methods. Features a flexible joint adaptor allowing the slide hammer to be used in restricted areas. EN0130 Oil Pump Primers Special design to hold the belt pulley on VW, AUDI. Applicable: VW: LUPO, POLO Classic, GOLF, BORA & CADDY. AUDI: A2 EN0111 VW Belt Pulley Holder Special design to hold the belt pulley on VW. Applicable: VW LUPO, POLO Classic, BEETLE, GOLF, BORA & CADDY. SEAT IBIZA CORDOBA. Set includes: 1PC 22mm special tube socket. 1PC oxygen sensor thread chaser. 1PC oxygen sensor wrenches offset (2-1/8") & super duty 12 & 6 point socket. 1PC oxygen sensor socket. EN PC Sensor & Sending Unit Socket Master Set Universal design for clamps onto any ribbed pulley. This tool can use for crankshafts, alternators, air conditioning units, and water pumps. EN0114 Oxygen Sensor Rethread Tool Cleans threads in oxygen sensor holes. Use with 3/4 hex socket or 3/8 square drive. M18X1.5 also works on m18x1.5 spark plug threads. These tools are designed to prime the lubricating system of a rebuilt engine prior to its first start to prevent the damage of a dry start. It works by connecting to the oil pump shaft through the distributor hole designed to be used with a 3/8 reversible drill. GM V6 and V8 oil pump primer. Oil pump primer for Fords with 1/4 hexes. Oil pump primer for Fords with 5/16 hexes. EN0233 Fuel Filter Key Fuel filter key Ø108. Suitable for Peugeot, Citroen, Renault e.g. with HDI diesel The fuel filter key is required to remove and install the fuel filter cap when replacing the fuel filter cartridge. Drive: 3/8 Dimension: Ø 108 mm. Suitable for most of vehicle of oxygen sensor and sending unit remover and install. 1PC 22mm special tube socket. 1PC oxygen sensor wrenches offset (2-1/8") & super duty 12 & 6 point socket. 1PC oxygen sensor socket. 1PC 1/2" drive x 29 x 90 mm oxygen sensor socket. 1PC 3/8" drive x 7/8" x 90mm oxygen sensor socket. 1PC 1/2" drive x 27 x 85mm injector socket. 1PC 3/8" drive x 7/8" x 80mm vacuum switch socket. 1PC 3/8" drive x 1-1/6" x74mm oil sender unit socket. 1PC 3/8" drive x 7/8" x 50mm heated oxygen sensor socket. 1PC 3/8" x 7/8" x 30mm offset oxygen sensor wrench. EN-4 EN-5

5 EN0118 Cam and Crank Shaft Seal Puller EN0065 Exhaust And Tailpipe Cutter EN0172 Fuel Line Pliers EN0183 8PCS Sensor Socket Set Engage the adjustable hook behind the seal. Brace the push rod against the engine head then push the handle to remove the seal. Remove the seal easily & quickly without damage to the cam & crank shaft. EN0119 3PCS Fuel Line Disconnect Set Fifteen blades effectively cut pipe so only 1/4 turn is needed for a complete cut. Use tool to cut pipes 3/4" to 3"(19 to 76mm) in diameter. Not for use on stainless steel pipe. EN0182 Diesel Injection Pump Puller For VOLKSWAGEN, AUDI, SEAT, SKODA Vehicle. For use on three ended hose clips which are fitted to, AUDI/ SEAT/SKODA/VOLKSWAGEN fuel lines clamps. Clamping range 28-18mm. EN0180 6PCS Diesel Injector Socket Kit 22mm special tube socket. Oxygen sensor thread chaser. Oxygen sensor wrenches offset (2-1/8") & super duty 12 & 6 point socket. Oxygen sensor socket. 1/2" drive x 29 x 90 mm oxygen sensor socket. 3/8" drive x 7/8" x 90mm oxygen sensor socket. 3/8" drive x 7/8" x 50mm heated oxygen sensor socket. 3/8" x 7/8" x 30mm offset oxygen sensor wrench. EN PCS Spark Plug Thread Repair Tool Set Design for uncoupling quick release fittings on fuel line to most of the cars. 1/4, 5/16 (Ø8mm) Ford-Mercury, Doge-Chrysler, Renault. 3/8 (10mm) Ford-Mercury, Doge-Chrysler, Renault. GM Chevrolet, Buick-Pontiac, Renault, Fiat, Ford, Opel. Suitable for BMW, LAND ROVER, VAUXHALL, OPEL 2.5 TDS engines diesel injection pump. EN0167 Water Pump Holding Tool This socket set can use for Alfa Romeo, Audi, Chrysler, Ford, Land Rover, Mercedes-Benz, Peugeot, Rover, Seat, Vauxhall and Volvo of diesel injector install and removal. EN0181 Oxygen Sensor Socket 1PC M16 x 1.25 x 70mm(L) tap reamer. 5PCS M14 x 1.25(11.2) replacement thread sleeve. 5PCS M14 x 1.25(17.5) replacement thread sleeve. 5PCS M14 x 1.25(17.5) replacement thread sleeve. EN0120 Universal Pulley Holder & Fan Clutch Set EN0189 Diesel Injection Pump Puller (BMW) This set is designed to removes and installs fan clutch & hold the camshaft pulley. Use for most of the cars. Contents with different tap to fit any cars and pin width can adjust. Can adjust different width from 40mm to 220mm. Size available: 2PCS Ø6mm-Ø10mm 2PCS Ø8mm-Ø11mm 2PCS Ø10mm-Ø12mm 2PCS Ø11mm-Ø16mm For OPEL ECOTECH engine. Simply remove access plate from front cover and install the tool to holding timing chain in place. Use for GM 2.2L & 2.4L ECOTECH engine in CHEVROLET OLDSMOBILE, OPEL/VAUXHALL PONTIAC and SATURN PLATFORMS. Application: GM ECOTECH 2.2 engine code F, CHEV CAVALIER, CHEV COBALT, CHEV MALIBU, OLDS ALERO, PONTIAC SUNFIRE, PONTIAC G5, PONTIAC GRAND AM, SATURN VUE, SATURN LON, SATURN L SERIES, 2.4 ENGINE CODE B, CHEV COBALT, CHEV HHR, CHEV MALIBU, PONTIAC G6, PONTIAC PURSUIT, PONTIAC SOLSTICE, SATURN AURA, SATURN LON, SATURN SKY 2.2 ENGINE 16V, ASTRA-G, ZAFIRA-A, VECTRA-B/C, SIGNUM and VX220. Applicable: FORD, TOYOTA, NISSAN, BENZ, BMW and most of European cars, also GM vehicles. Flare nut for vacuum switch & oxygen sensor service on the computer-controlled 3/8 of the double square DR. 7/8 (22mm) 12 points & 22mm 6 point. EN0198 Engine Oil Dipstick For Audi Engine oil dipstick applicable to 2009 Audi A4, A5 and A6 with engines 2.0L TFSI, 3.2L FSI and 4.2L FSI. This tool is specifically designed for holding the sprocket/chain in place when disassembling the VP44 injection pump and high pressure pump. Common rail fitted to BMW engines: 318D/COMPACT(E46) 320D/TD COMPACT(46) 330D(E46) 525D(E39) 525D(E60/E61) 530D(E39) 530D(E60/E61) 535D(E60/E61) 730D(E38) X5 3.0D(E53) EN-6 EN-7

6 EN0185 Cam Seal Installer(FOR MAZDA, NISSAN, TOYOTA/LEXUS) EN0187 4" Offset Harmonic Damper Pulley Holding Tool (HONDA & ACURA) EN0190 Diesel Injection Pump Puller (LAND ROVER) EN0193 7PCS Injector Puller This tool is designed to install the cam seals in 4&6 cylinder engines for MAZDA, NISSAN & TOYOTA/LEXUS engines that have 10&12mm*1.25 cam bolts. These engines are mounted transversely which puts the camshaft end in very close proximity to the shock tower making replacement of the cam seal extremely difficult using conventional methods. Screw the threaded rod into the cam end, slide the body over the rod against the seal and press in the seal using the nut provided. EN0186 Slide Hammer Type Injector Nozzle Puller Can use for Mercedes CDI engines OM 611, 612, 613, etc. Injection nozzles that do not fit very tightly can be pulled out without needing to take them apart or remove the cylinder block. The specialty design, the puller is additionally supported by the steel ball on the valve cover, which prevents the puller from tipping during the removal process. EN0188 Glow Plug Remover Tool This unique tool has been developed to aid in the removal and installation of the crank bolt on most HONDA and ACURA It has been re-engineered to work on 2004 and later new style SUV'S with a 50mm damper pulley as well as all previous models serviced. In operation with the use of a 1/2" breaker bar or ratchet this tool holds the harmonic damper pulley from rotating when removing and setting the final torque specification on the pulley bolt. There is a hole in the center of the tool to allow the use of a socket and extension to break loose or tighten the pulley bolt. Application: For HONDA ACCORD 2.2L 4 CYLINDER 90-97, 2.7L V , 2.3L 4 CYLINDER 98-02, 2.4L 4 CYLINDER 03 & LATER, 3.0L V-6 98 & LATER. CIVIC 1.6L 4 CYLINDER 92-00, 1.7L 4 CYLINDER 01 & LATER, 2.0L 4 CYLINDER 03 & LATER. CRV 2.0L 4 CYLINDER 97-01, 2.4L 4 CYLINDER 02 & LATER. DEL SOL 1.6L 4 CYLINDER INSIGHT 1.0L 3 CYLINDER 00 & LATER. ODYSEY 2.2L 4 CYLINDER 95-97, 2.3L 4 CYLINDER 98, 3.5L V-6 99 & LATER. PILOT 3.5L V-6 03 & LATER. PRELUDE 2.2L 4 CYLINDER 92-01, 2.3L 4 CYLINDER S L 4 CYLINDER 00-03, 2.2L 4 CYLINDER 04 & LATER. ELEMENT 2.4L 4 CYLINDER 03 & LATER. RIDGELINE 3.5L V-6 06 & LATER. For ACURA CL 2.2L 4 CYLINDER 97, 3.0L V , 2.3L 4 CYLINDER 98-99, 3.2L V INTEGRA 1.6L 4 CYLINDER 90-92, 1.7L 4 CYINDER 92-93, 1.8L 4 CYLINDER LEGEND 3.2L V MDX 3.5L V-6 01 & LATER. RL 3.5L V-6 96 & LATER. RSX 2.0L 4 CYLINDER 02 & LATER. TL 3.2L V-6 95 & LATER. TSX 2.4L 4 CYLINDER 04 & LATER. RDX 2.3L 4 CYL TURBO 06 & LATER. This tool is specifically designed for holding the sprocket/chain in place when disassembling the VP44 injection pump and high pressure pump. Common rail fitted to LAND ROVER engines: LAND ROVER, FREELANDER(TD4), ROVER 75(M47). EN0191 Injector Puller For Bosch injector system of Mercedes Benz. For removing adapted tight common rail injectors without having to disassemble cylinder head. Use for Mercedes-Benz CDI engines ,etc. Injection puller with impact hammer, injection nozzles, that do not fit very tightly can be pulled out without needing to take them apart or remove the cylinder block. EN0192 6PCS Injector Puller(For BOSCH Injector System of MERCEDES-BENZ) For Bosch injector system of Mercedes Benz. For removing adapted tight common rail injectors without having to disassemble cylinder head. Use for Mercedes-Benz CDI engines ,etc. Injection puller with impact hammer, injection nozzles that do not fit very tightly can be pulled out without needing to take them apart or remove the cylinder block. EN0194 Universal Camshaft Sprocket Puller Hold the sprocket and undo the retaining bolt or nut and remove. This tool enables the removal of the camshaft sprocket on a wide range of vehicles. Suitable size from 45mm to 70mm. EN0195 Diesel Injector Seat Cutter Set The 10mm split nut will work on ford 6.9L and 7.3L diesels, GM 5.7L, 6.2L, and 6.5L diesels; and various diesels in import vehicles. Plus many agricultural and construction diesel applications. For removing adapted tight common rail injectors without having to disassemble cylinder head. Use for MERCEDES-BENZ CDI engines ,.etc. Injection puller with impact hammer, injection nozzles that do not fit very tightly can be pulled out without needing to take them apart or remove the cylinder block. This kit has been specially designed for the clean and recutting of injector seats on modern common rail diesel The kit includes 4 seat cutting reamers for Bosch, Delphi and universal application along with a special angled reamer for IVECO/FIAT applications. EN-8 EN-9

7 EN0197 Diesel Injector Nozzle Socket EN0196 Diesel Injector Seat Cutter Set EN0225 2PCS Rubber Ring Hook Tool Set EN Tail Pipe Cutter The set include 4pcs diesel injector nozzle socket. 1/2 DR socket can use for SIEMENS & BOSCH injectors. Suitable for Peugeot and Citroen with 2.0 engines (110/135hp) HDI EN0199 Copper Washer Removal Tool For Diesel Injector This kit has been specially designed for the clean and recutting of injector seats on modern common rail diesel The kit includes 4 seat cutting reamers for Bosch, Delphi and universal application along with a special angled reamer for IVECO/FIAT applications. Material: high carbon steel SKD-11. EN0221 Ratcheting Serpentine Belt Wrench Set Special designed to pull the rubber ring which connected with exhaust tube. Two special angle hook attached. EN0206 Mechanic s Stethoscope Lubricate cutting wheels with light machine oil prior to use and before storage. Turn cutter handle counterclockwise to extend shaft as needed to fit pipe diameter. Wrap chain around pipe and hook link into tabs on cutter handle. Turn cutter handle as needed to ensure chain fits snugly around pipe. do not over tighten. Slowly rotate cutter around pipe. As cutting progresses, turn cutter handle slightly to maintain snug pressure. Take multiple shallow cuts for best results. Use for 3-1/2 to 6 tail pipe. EN0249 Water Pump Removal Tool Kit Size: Inner hole: 7mm. Length: 230mm. Collet type easy to holding the copper washer. EN0222 Exhaust Pipe Hanger Stretcher Service approximately 90% of all vehicles equipped with spring-loaded serpentine belt tensioners. Ratcheting action allows quickly and easy positioning of wrench driving end for tensioner access from any angle. For use when servicing serpentine drive belts or any beltdriven accessories. Specifically designed to fit into tight areas. EN0205 Mechanic s Stethoscope Provides a fast and easy way to locate noise in engine or bearing and other moving parts. High quality surgical PVC and rubber parts for increased sound definition. Aluminum alloy probe / needle for finding the exact location of specific noises. EN0200 Fuel Pump Wrench Use for VOLKSWAGEN T5 & TOUAREG 2.5D water pump removal. Application for engine code, BAC, BLK, BPD, BPE. Wrench for removal and installation of the fuel pump on Audi 90 Quattro. EN0320 Adjustable Piston Ring Installer EN0239 Valve Shim Remover Stretcher removes exhaust systems for rubber-style hangers easily. The slip-resistant handles and self-locking force pin allow for quick removal of rubber exhaust hangers. A slim profile and 25 offset allow for easy access to confined areas. Provides a fast and easy way to locate noise in engine or bearing and other moving parts. High quality surgical PVC and rubber parts for increased sound definition. Aluminum alloy probe / needle for finding the exact location of specific noises. Supplied with a rubber trumpet for checking vacuum and pressure flow. For use on Opel, Volvo and some European Cars with overhead camshafts which use spacer shim. Fits piston range from 3/64 to 1/4 thick. Makes installing piston rings safe and easy without over expanding rings. Works on most common piston rings. Adjustable spread stop for fast bread free installation and removal. EN-10 EN-11

8 EN0207 Diesel Injector Seat Cutter Set EN0230 Diesel Injectors Seat Cuter and Face Cleaner EN0241 Impact Diesel Injector Remover VAG EN PCS Spark Plug Thread Set M14X1.25 This kit has been specially designed for the clean and recutting of injector seats on modern common rail diesel The kit includes 4 seat cutting reamers for BOSCH, DELPHI and universal application along with a special angled reamer for IVECO/FIAT applications. EN0247 Piston Ring Compressor Set Installs pistons from 2-7/8 to 4-3/8 (73mm to 111mm). Ratcheting lock allows for bands to compress in small increments. Can be used parallel vertically perpendicular horizontally. Set includes pliers and six bands. EN ratchet pliers. EN band size 2-7/8 to 3-1/8. EN band size 3-1/8 to 3-3/8. EN band size 3-3/8 to 3-5/8. EN band size 3-5/8 to 3-7/8. EN band size 3-7/8 to 4-1/8. EN band size 4-1/8 to 4-3/8. EN band size 4-3/8 to 4-5/8. After removing used injector from cylinder head is important to clean seat of injector, by this tool you can clean seat as well as injector seat. All process is made manually by turning by hand with apply little bit of pressure. EN PCS Oxygen Sensor Thread Set M18X1.5 A unique tool for repair damaged spark plugs, glow plugs and Lambda probe threads. Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 1 PC Thread cutting tap M18 x 1.5 L=50mm 1 PC Thread cutting tap M20 x 1.5 L=50mm 1 PC Piloted reamer M18 x 1.5 L=50mm 1 PC Screw in tool for insert nut L=90mm M18 x PC Screw sleeve 27H x 81mm 5 PCS Insert nut with collar, L=9mm IG=M18 x 1.5/AG=M20 x 1.5 5kg slide hammer with threaded adaptors for removing seized fuel injectors from VAG TDI The kit includes direct, offset and hook adaptors. EN PCS Glow Plug Thread & Spark Plug Set M12X1.25 A unique tool for repair damaged spark plugs, glow plugs and Lambda probe threads. Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 1 PC Piloted tap M12 x PC Piloted tap M14 x PC Piloted reamer M12 x PC Screw in tool for insert nut, L=100mm M12 x PC Screw sleeve 19H x 89mm 5 PCS Insert nut with collar, L=12mm IG=M12 x 1.25/AG=M14 x PCS Insert nut with collar, L=19mm IG=M12 x 1.25/AG=M14 x PCS Insert nut with collar, L=26mm IG=M12 x 1.25/AG=M14 x PC Screw in tool for insert nut L=107mm M12 x PC Screw in tool for insert nut L=114mm M12 x 1.25 A unique tool for repair damaged spark plugs, glow plugs and Lambda probe threads. Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 1 PC Thread cutting tap M14 x 1.25 L=70mm 1 PC Thread cutting tap M16 x 1.25 L=70mm 1 PC Piloted reamer M14 x 1.25 L=70mm 1 PC Screw in tool for insert nut L=100mm M14 x PC Screw sleeve 23H x 90mm 5 PCS Insert nut with collar, L=11.2mm IG=M14 x 1.25/ AG=M16 x PCS Insert nut with collar, L=17.5mm IG=M14 x 1.25/ AG=M16 x PCS Insert nut with collar, L=17.5mm IG=M14 x 1.25/ AG=M16 x 1.25 cone 1 PC Screw in tool for insert nut L=106mm M14 x 1.25 EN0204 Oscillating Valve Lapper Laps valves in double quick time. Gas tight seal in seconds. Unique patented mechanism converts rotary drill action to oscillating grinding motion. 22/28mm sucker heads fits most valve sizes. Fit all power drills with 5/16"(8mm) chuck. Essential on multi-valve EN-12 EN-13

9 EN PCS Glow Plug Thread Set M10X1.0 EN PCS Glow Plug Thread Set M10X1.25 EN0203 Korean Vehicle Diesel Injector Puller Set EN PCS Glow Plug Thread Set M8 x 1.0 A unique tool for repair damaged spark plugs, glow plugs and Lambda probe threads. Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 1 PC Piloted tap M10 x PC Piloted tap M12 x PC Piloted reamer M10 x PC Screw in tool for insert nut L=106mm M10 x PC Screw sleeve 17H x 85mm 5 PCS Insert nut with collar, L=12mm IG=M10x1.0/ AG=M12x1.0 5 PCS Insert nut with collar, L=19mm IG=M10x1.0/ AG=M12x1.0 1 PC Screw in tool for insert nut L=103mm M10x1.0 A unique tool for repair damaged spark plugs, glow plugs and Lambda probe threads. Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 1 PC Piloted tap M10 x PC Piloted tap M12 x PC Piloted reamer M10 x PC Screw in tool for insert nut, L=100mm M10 x PC Screw sleeve 17H x 89mm 5 PCS Insert nut with collar, L=12mm IG=M10 x 1.25/AG=M12 x 1.25 Special design used for remove diesel injectors of most Korean vehicles. Application: Hyundai:STAREX, LAVITA, MARTIX, TRAJET, TERRACAN, SANTA FE, LIBERO, AVANTE XD, GRANDEUR XG, GETZ, TUESON, NF SONATA, 06 ACCENT. KIA: CARNIVAL, RIO, CARENS, CERATO, OPTIMA, PICANTO, SORENTO, SPORTAGE,GRAND CARNIVAL. EN0248 Crankshaft Sealing Flange Removing & Installing Tool A unique tool for repair damaged spark plugs, glow plugs and Lambda probe threads. Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 1 PC Piloted tap M8 x PC Piloted tap M10 x PC Piloted reamer M8 x PC Screw in tool for insert nut L=100mm M8 x PC Screw sleeve 14H x 90mm 5 PCS Insert nut with collar,l=11mm, IG=M8 x 1.0 / AG=M10 x 1.0 EN0240 4PCS Diesel Injector Removal Set For DELPHI/BOSCH EN PCS Oxygen Sensor Thread Set M12X1.5 A unique tool for repair damaged spark plugs, glow plugs and Lambda Applicable:16V,1.4,1.6 engine of VW,AUDI,SKODA,SEAT. Special design tool to replacement crankshaft sealing flange. probe threads. EN0246 Fuel Feed Pipe Pliers Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 1 PC Thread cutting tap M12 x 1.5 L=50mm 1 PC Thread cutting tap M14 x 1.5 L=50mm 1 PC Piloted reamer M12 x 1.5 L=50mm 1 PC Screw in tool for insert nut L=100mm M12 x PC Screw sleeve 19H x 93mm 5 PCS Insert nut with collar, L=9mm IG=M12 x 1.5/AG=M14 x 1.5 For undoing quick release connections on fuel feed pipe lines. Suitable for OPEL/VAUXHALL, FIAT, GM, VW.etc. Adaptors can also be used with an air tool to loosen the injectors by vibration. Set of 3 adaptors plus a special tool for removing the internal part of BOSCH injectors. Specifically designed for removing DELPHI/BOSCH diesel injectors using a slide hammer with 5/8 UNF thread. EN-14 EN-15

10 EN PCS Glow Plug Thread Set M9 x 1.0 EN0236 Valve Stem Seal Tool Set EN PCS Oxygen Sensor Special Socket Set EN PCS Opening Single Ended Ratchet Wrench A unique tool for repair damaged spark plugs, glow plugs and Lambda probe threads. Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 1 PC Piloted tap M9 x PC Piloted tap M11 x PC Piloted reamer M9 x PC Screw in tool for insert nut L=103mm M9 x PC Screw sleeve 17H x 93mm 5 PCS Insert nut with collar, L=11mm IG=M9 x 1.0 / AG=M11x1.0 EN0229 8PCS Diesel Injector Seat Cutter Set For Valve Stem Sealing Rings. This tool set allows the removal and replacement of valve shaft sealing rings. Consists of: Basic Slide Hammer Valve Seal Collect Chuck (bucket-tappets diam. 26 mm upwards) Valve Seal Collect Chuck (bucket-tappets diam. 23 mm up to 26 mm) Oil Seal Removal Pliers - Long Press Set for valve seals (10 pcs., Ø mm inside) EN0310 Piston Ring Service Tool Set 17x78mmL(12PT):REUAULT. 19x78mmL(12PT):VW POLO, AUDI, SEAT, MAZDA. 20x78mmL(6PT):ABIERTU JAPAN. 27x78mmL(6PT):ABIERTU JAPAN. 21x90mmL(12PT):SEAT, AUDI,VW,SKODA,ALFA, ROMEO,MITSUBISHI. 22x78mmL(12PT):SEAT, AUDI,VW, SKODA,OPEL. 22x110mmL(12PT):MERCEDES, CITROEN, PEUGEOT,FORD, NISSAN. MAZDA, MITSUBISHI, SEAT, AUDI,VW, ETC. 27x78mmL(12PT):SEAT, AUDI, VW, SKODA, BMW, MERCEDES, OPEL FORD, NISSAN, MITSUBISHI, LIN COLN(USA). 27x110mmL(12PT):CITROEN, PEUGEOT, SISTEN LVCAS. 28x78mmL(12PT):ALFA ROMEO, FIAT, ROVER, OPEL. 30x78mmL(12PT):MERCEDES. 22x150mmL(12PT). 7/8" OFFSET OXYGEN SENSOR SOCKET. 7/8" OFFSET DEEP OXYGEN SENSOR SOCKET. 29x90mmL (6PT) 22x80mmL (6PT) 22x90mmL (6PT) 1" & 1-1/16" x 74mmL Can be used on pneumatic & hydraulic connections such as brake pipes. Size: 10mm, 11mm, 13mm, 17mm, 19mm, 22mm EN0309 Valve Spring Compressor EN mm-160mm Piston Ring Pliers Compressor easily and removes valve springs on most cars and light trucks, Work with cylinder head on or off the engine.. EN mm 100mm Piston ring Pliers Tools are used for cleaning place under injection washer after replacing injector. It is necessary to clean place under and above washer for perfect fit new or replaced diesel injector. Do not use with air tools. Piston ring compressor with ratchet key: 1 PC Height: 3, capacity mm. 1 PC Height: 3-1/2, capacity mm. 1 PC Height: 4, capacity mm. Piston ring tool capacity: mm. Piston ring groove cleaning fits: 2-5 (51-127mm). Cleaning blade 1 size: 1/16 to 3/16. Cleaning blade 2 size: 2.0mm to 4.5mm,1/4 Cleaning blade 3 size: 1.2mm to 5.5mm Offset driver: Phillips and slotted. For removing and mounting piston rings. Capacity: 110mm-160mm Finish: Nickel plated. For removing and mounting piston rings. Capacity: 50mm-100mm Finish: Nickel plated. EN-16 EN-17

11 EN mm-120mm Piston Ring Pliers EN0321 Cylinder Base Surface Rectifier EN PCS Oil Drain Repair Kit EN0324 Replaceable Oil Pan Separator and Clean Kit For removing and mounting piston rings. Capacity: 80mm-120mm Finish: Nickel plated. EN0311 -EN0317 Piston Ring Compressor Straight edge works for precision check the cylinder head or flat damage or not. Size: Length: 600mm. Width: 50mm. Hight: 7mm. EN0322 Stud Remover and Installer Set Breaks gasket seals on engine sumps, transmissions or any difficult to separate gasket joints. 1PC M13 x 1.25P re-thread tap. The copper blade could avoid damage on gasket or oil pan 6PCS M13 x 1.25P drain bolt. connection joint surface. 1PC M13 x 1.5P re-thread tap. Clean up wheel tool helps use to clean all small space on 6PCS M13 x 1.5P drain bolt. cylinder head. 1PC M15 x 1.5P re-thread tap. 6PCS M15 x 1.5P drain bolt. 1PC Replaceable separator steel plate. 1PC M17 x 1.5P re-thread tap. 1PC Replaceable copper plate. 6PCS M17 x 1.5P drain bolt. 1PC 2.5mm alley key. Material: Special spring steel (SK) with heat treaded. Ratchet type complete with spanner. Tool with safety adjusting screws. Size range: Item No. Height Capacity (mm) EN EN / EN EN / EN EN EN / Easily remove and install studs without damaging the thread. Size: M6 x 1.0 M8 x 1.25 M10 x 1.25 M10 x 1.5 EN0327 Camshaft Seal Installer 1PC M20 x 1.5P re-thread tap. 6PCS M20 x 1.5P drain bolt. 1PC M22 x 1.5P re-thread tap. 6PCS M22 x 1.5P drain bolt. 72PCS copper washer. EN0328 Clutch Alignment Rectifier 1PC Clean cup wheel adapter. 15PCS Clean cup brush wheel. EN0325 5PCS Glow Plug Socket EN0143 Cylinder Base Surface Rectifier Straight edge works for precision check the cylinder head or flat damage or not. Size: Length: 600mm. Width: 36mm. Hight: 16mm. Special tool for easily and quickly install camshaft seal in 4 and 6 cylinder. Material of main body: S45C. Material of spindle: S45C. Material of hex nut: S45C. Spindle sizes: 1/2-20 x M10 and 1/2-20 x M12. Applicable: MAZDA, NISSAN, TOYOTA, LEXUS.etc. Align single disc clutches on most of vehicles, light truck and tractors. Properly aligns clutch plate by tapered cone fitting into pilot bushing or bearing. 8PCS collects ranging from (11mm) to (24.9mm). Design for glow plug remover and install. Use with 1/4 Dr. wrench. Size and applicable: 8mm for Peugeot, Renault, Citroen, Ford and Mercedes-Benz. 9mm for Opel, FIAT, LANCIA, Alfa, SEAT and VW/AUDI. 10mm for Mercedes-Benz, Peugeot, SEAT, AUDI and VW. 12mm for Peugeot, Renault, Citroen, BMW and OPEL. 14mm Universal type. EN-18 EN-19

12 EN0326 Spark Plug Thread Repair Kit EN0320 Adjustable Piston Ring Installer EN0342 Serpentine Belt Tool EN0102 Valve Spring Compressor For large engines and diesel This tool kit is designed for repairing stripped or damaged threads on spark plug seat. 1PC Tap M14 x 1.25P. 1PC Step-tap M14 x 1.25P, M15.8 x 1.25P. 1PC Wrench (inside diameter 3/8 ). 1PC 3/8 Dr. T-bar. 1PC Insert driver (inside diameter 3/8 ). 1PC Seat cutter. 10PCS Copper thread sleeve length 15mm. 10PCS Copper thread sleeve length 9.4mm. 1PC Alley key 2.5mm. Fits piston range from 3/64 to 1/4 thick. Makes installing piston rings safe and easy without over expanding rings. Works on most common piston rings. Adjustable spread stop for fast bread free installation and removal. EN0005 Valve Adjusting Tool (For TOYOTA) Releases tension on serpentine belts with spring loaded idler pulley. This tool is used to remove and install belts on serpentine belt systems using the spring loaded idler pulley. Fits idler pulleys requiring 13mm, 15mm, 16mm, 18mm, or 3/8" square drive socket size, which are on most all domestic applications. EN0346 Pin Spanner Wrench Unique direct action compressor lever gives improved visibility and ease of use in areas of difficult access. Collet release adapters. Restricted access adapter 25mm and 30mm. Jaw opening Min.: 35mm. Jaw opening Max.: 200mm. Clearance: 250mm. EN0103 Valve Spring Compressor Capacity mm, throat clearance 165mm designed for use on multi - valve petrol and diesel engines with deep seated EN0149 Pulley Removing Wrench For Toyota and other overhead camshaft engines using space shims. Shim pliers push between the shim and camshaft allowing the Universal design fits many different types of pulleys having slots or holes. Tool also fits camshaft pulleys and crankshaft pulleys. Adjustable wrench from 1-1/4 to 5. Wrench work with a 1/2 Dr. ratchet or breaker bar. valves. Collet release adapters. Restricted access adapter 25mm and 30mm. Suitable for general use on a wide range of OHC, OHV, and CVH Universal model with unique dual cam-action, parallel lift and automatic locking. Reversible jaw and adaptor. included wedge tool to be placed between the valve lifter ledge and camshaft for Pin Size: 3.5mm, 4mm, 4.5mm, 5mm, 6mm, 7mm, 10mm. EN0348 Spark Plug Hole Thread Chaser EN0136 Universal Belt Tension Gauge easy shim replacement. Ideal for removing and assembling any type of grooved pulley for V-type belt. This tool keeps the grooved pulley firmly locked. Enable to tighten or to un-tighten without any difficulty pulley locking screw. Has more functions than a standard strap or chain wrench and will not damage the components. Idea for alternator and water pump pulleys, but also essential for electric Motors of compressors, washing machines, tool machines etc. Also suitable to rotate the camshaft when timing the engine and to remove oil and gasoline filters. EN0015 Oxygen Sensor Thread Chaser Cleans threads in oxygen sensor holes. Use with 3/4" hex socket or 3/8" square drive. Size: M18x1.5 Also works on M18x1.5 spark plug threads. Tapered double ended for both 14mm and 18mm threads designed to start and remove carbon and dirt or straighten damaged threads in spark plug hole. M14 x 1.25 / M18 x 1.5, Hexagon : 21mm Material: S45C with heat treatment This tensioning gauge can be used to adjust the tension on the cam belts where the movement of the timing belt is measured by load. Clear incremental marking with knurled knob for precise measurement. Dual scale allows reading from top or bottom of tool. EN-20 EN-21

13 EN0349 Spark Plug Hole Thread Chaser EN0198 Engine Oil Dipstick For Audi EN mm Fan Clutch Tool EN0278 Crankshaft Seal Installer Tapered 14mm threads designed to start and remove carbon & dirt or straighten damaged threads in spark plug hole. Size: M14 x 1.25, Hexagon : 22mm Material: S45C with heat treatment. EN0191 Injector Puller Engine oil dipstick applicable to 2009 Audi A4, A5 and A6 with engines 2.0I FSI, 3.2l FSI and 4.2l FSI. EN0251 Viscous Fan Hub Spanner Size: 36mm x 380mm. For removal of thermo, viscous fan hubs. For Ford Granada 2.4 & 2.9 GM Carlton, Manta & Senator. Finish: Polish with mirror chrome plated. EN PCS Injector Copper Sealing Ring Kit This crankshaft seal removal and installer tool has been introduced for use on Golf, Touran, Audi A3 (04-) and also for 4 cylinder diesel Application: 1.4 Turbo, 1.4 / 1.6 Direct Injection (Petrol), 1.9 / 2.0 SDI, 2.0 TDI and 2.0 common rail (Diesel). Material: Aluminum and carbon steel. EN0252 Clutch Spring Compressor For removal of thermo, viscous fan hubs, cranked for easy access. Size: 32mm x 380mm Application for BMW 316, 520i, 525i, 530i, 535i, 730i and 735i Suitable for Bosch injector system of Mercedes Benz. and Ford. For removing adapted tight common rail injectors without having to disassemble cylinder head. Use for Mercedes Benz CDI engines ,..etc. Injection puller with impact hammer, injection nozzles that do not fit very tightly can be pulled out without needing to take them apart or remove the cylinder block. EN0249 Water Pump removal Tool Kit EN0293 9PCS Diesel Injector Seat Cutter Set Universal copper sealing ring have 15 different size combinations is suitable for most of popular nozzle of injector system. (each number have 30 piece sealing ring) No. O.D I.D Thickness For removing and installing the transmission rear clutch piston snap ring adjustable. Suitable for most American cars and light trucks mm 7.0mm 2.0mm mm 7.5mm 1.0mm mm 7.5mm 1.5mm EN0319 Exhaust Spring Clamp Remover and Installer mm 7.5mm 2.0mm mm 7.5mm 2.5mm mm 7.5mm 3.0mm mm 7.5mm 1.5mm Use for Volkswagen T5 & Touareg 2.5D water pump removal. Application for engine code BAC, BLK, BPD, BPE. This kit has been specially designed for the clean and recutting of injector seats on modern common rail diesel The kit includes 5 seat cutting reamers for Bosch, Delphi and universal application along with a special angled reamer for IVECO/FIAT applications. Include 3 sizes of reamer chuck for 17, 19 and 21mm is suitable cleaning for injector nozzle end mm 7.5mm 1.7mm mm 7.5mm 2.0mm mm 7.5mm 2.0mm mm 7.4mm 2.0mm mm 9.4mm 0.9mm mm 7.3mm 1.4mm mm 7.5mm 1.3mm mm 7.5mm 3.0mm Essential for safe, controlled removal of clamps attaching exhaust to manifold. Special design provides leverage required to expand the strong spring clamps. Application for VW vehicles. EN-22 EN-23

14 EN0329 8PCS Sensor Socket Master Kit EN0330 Diesel Injector Removal Set EN PCS Master Rethread Tool Kit EN0338 Valve Refacing and Seating Tools Specifically designed for removing Delphi/Bosch diesel injectors using a slide hammer with 5/8 UNF thread. Design for the removal and installation of oxygen sensors, oil pressure sending units and vacuum switches. Made by Chrome-Vanadium steel. 1PC 1-3/16" (29mm) 1/2" Dr. oil sensor socket. 1PC 7/8"(22mm) slotted 3/8" Dr. PVS, TVS and O2 sensor. 1PC 1-1/16"(27mm) 1/2" Dr. GM thermal sensor switch. 1PC 7/8"(22mm) oxygen sensor socket. 1PC 1-1/16" oil pressure sending unit 3/8" Dr. 1PC 7/8"(22mm) oxygen sensor socket. 1PC 7/8"(22mm) low profile offset oxygen sensor. 1PC 1-1/16" short access socket 3/8" Dr. Set of 3 adaptors plus a special tool for removing the internal part of Bosch injectors. Suitable for Bosch/Delphi injectors as well as Mercedes-Benz cdi engine on 611, 612, 613 etc. Hammer weight: 1.8kg. EN0331 Extra Long Oxygen Sensor Socket A unique tool for repair damaged spark plugs, glow plugs and lambda probe threads. Quick and easy repair without extensive component disassembly. Easy to use and proper fixed with absolute gas-tight seating of the inserts. 10PCS glow plug rethread tool M8 X PCS glow plug rethread tool M9 X 1.0. Precision machined tungsten carbide blades produce valve seats with, accurate seat angle, superior seat surface true, flat seal and seats concentric with valve guide. Available in a wide range of cutter diameters and angles. Application: 1PC cutter ø37mm- ø46mm 60 and 45. 1PC cutter ø37mm- ø44mm 75 and 30. 1PC cutter ø28mm- ø37mm 75 and 45. 3PCS expandable pilot T wrench handle. EN PCS Injector Copper Sealing Ring Kit 16PCS glow plug rethread tool M10 X 1.0. EN0337 Valve Refacing and Seating Tools 10PCS glow plug rethread tool M10 X PCS glow plug rethread tool M12 X For removing and install lambda sensors with a deep-seated hexagon. Particularly suitable for the Mercedes-Benz C/E, 602,605,606, VW, Audi, Skoda, Seat, BMW. Ford, Opel, Rover, Volvo. Material: CR-MO steel. 10PCS oxygen sensor rethread tool M12 X PCS spark plug rethread tool M14 X PCS oxygen sensor rethread tool M18 X PC rethread gauge set. 1PC brass cleaning brush. 1PC nylon cleaning brush. 1/2" Dr. length 150 mm(l). Size: 22mm x 6PT x 150mm(L). EN0334 Injector Seat Cleaning Set EN0332 VW/Audi Diesel Injector Remover Universal copper sealing ring have 15 different size combinations is suitable for most of popular nozzle of injector Precision machined tungsten carbide blades produce valve seats with accurate seat angle, superior seat surface true, flat seal and seats concentric with valve guide. system. (each size have 10 piece copper sealing ring) O.D x I.D x Thickness: Available in a wide range of cutter diameters and angles x 7.3 x 1.4(mm) 14.6 x 7.5 x 1.3(mm) 14.6 x 7.5 x 3(mm) application: 1PC cutter ø52mm- ø65mm 75 and 60. 1PC cutter ø46mm- ø60mm 45 and 30. 1PC cutter ø44mm- ø52mm 75 and 30. 1PC cutter ø37mm- ø46mm 60 and 45. 1PC cutter ø37mm- ø44mm 75 and 30. 1PC cutter ø28mm- ø37mm 75 and 45. 5PCS expandable pilot ø5.5mm- ø12.5mm T wrench handle. Special design to remove the diesel injector form VAG group TDI Special two design to fix the injector and pull out with slide hammer. Applicable: For VW, AUDI engine code ALH, AHU, IZ, Seat and Skoda. Suitable for 2.0 TDI engine from VAG group. To clean the contact surface between the injector and engine head when making the replacement. Include cutter holder can made cutter is straight and correct to attach when do cleaning. Insert the extension bar in to the cutter for deep hole cleaning. 15 x 7 x 2(mm) 15 x 7.5 x 1(mm) 15 x 7.5 x 1.5(mm) 15 x 7.5 x 2(mm) 15 x 7.5 x 2.5(mm) 15 x 17.5 x 3(mm) 15.5 x 7.5 x 2(mm) 16 x 7.5 x 1.5(mm) 16 x 7.5 x 1.7(mm) 16 x 7.5 x 2(mm) 16.4 x 7.4 x 2(mm) 20 x 9.4 x 0.9(mm) EN-24 EN-25

15 EN0343 VW/Audi Diesel Injector Remover EN0002 Universal Pulley Holder EN0354 Spark Plug Hole Thread Chaser EN0358 Offset Distributor Clamp Wrench Tapered 12mm threads designed to start and remove carbon and dirt or straighten damaged threads in spark plug hole. The tool designed to trap and hold bolt-on pulleys by the mounting bolt on most pulleys. Use with deep socket, open ends or boxes wrench. Thread size: M12 x Hex subtense size: 22mm. Contains two offset box wrenches sizes 13mm and 15mm. 13mm Application: 1981 and later Ford V6 (3.8L) Special design to remove the diesel injector for VAG group TDI Special two design to fix the injector and pull out with slide hammer. Applicable: For VW, AUDI TDI engine code ALH, AHU,IZ, SEAT and SKODA. EN0345 VW/ Audi Special Wrench EN0355 Spark Plug Hole Thread Chaser Ford Tempo and Topaz 2.3L HSC vehicles and later GM Blazers with V6 (2.8L) 15mm Application: GM "X" body cars with V6 (2.8L) 1982 and later Cadillac V8 (4.1L) GM V6 (2.8L) engines and 1985 VW Golf. Use tool by itself or turn with 3/8" Dr. ratchet. Drop forged steel construction. Chrome plated to resist corrosion. Tapered threads designed to start and remove carbon and dirt EN0347 Thin Jaw Bearing Puller Special angle wrench for VW / Audi TDi, Turbo system. or straighten damaged threads in spark plug hole. Use with deep socket, open ends or boxes wrench. Thread size: M10 x 1.0 and M12 x EN0353 Spark Plug Hole Thread Chaser Size: 3/8 Dr. x 12mm (12PT) Hex subtense size : 21mm. EN0351 Pulley Puller EN0356 Spark Plug Hole Thread Chaser Special design for removing bearing in narrow space. Reach: 93mm. Applicable bearing dimension: 30-90mm Jaw thickness: 1.5mm. Tapered 18mm threads designed to start and remove carbon and dirt or straighten damaged threads in spark plug hole. Use with deep socket, open ends or boxes wrench. Thread size: M18 x 1.5. Hex subtense size: 22mm. Tapered threads designed to start and remove carbon and dirt EN0359 Universal Stretch Belt Installation Tool Removes pressed on 1 or 2 groove pulleys from alternators or power steering pumps. Also easily removes alternator bearings. or straighten damaged threads in spark plug hole. Use with deep socket, open ends or boxes wrench. Thread size: M12 x 1.25 and M14 x Hex subtense size : 21mm. EN0360 Air Operated Valve Lapper Adjusted by simple thumbscrew movement. EN0352 Spark Plug Hole Thread Chaser EN0357 Offset Distributor Clamp Wrench 2PCS universal stretch belt tool. Universal stretch belt installation tool is available separately for applications where a tool must be used. The universal tool is more economical and environmentally friendly than disposable versions. Stretch fit installation kit includes a re-usable universal tool and mounting bolt. Tapered 18mm threads designed to start and remove carbon and dirt or straighten damaged threads in spark plug hole. Use with deep socket, open ends or boxes wrench. Thread size: M18 x 1.5. Hex subtense size: 21mm. Contains two offset box wrenches sizes 1/2" and 9/16". Use tool by itself or turn with 3/8" Dr. ratchet. Drop forged steel construction. Chrome plated to resist corrosion. Design for operating in tough environments. Adjustable speed regulator for precise control during operation. Complete with rubber caps of 20mm, 30mm, 35mm and 45mm. EN-26 EN-27

16 EN0361 Diesel Engine Glow Plug Repair Kit EN0363 VW and AUDI Injector Remover EN0366 3PCS Sensor Socket Set EN PCS Sensor and Diesel Injection Socket Set Diesel Engine requires glow plug for combustion process in engine cylinder. The heating element in glow plug heat up and drive the cylinders gradually. But the heating elements are very delicate and require special tool for removing the glow plug. EN0362 Temperature Sensor Special Socket Set Use U sleeve or two jaws hook to fix the injector and then pull out with slide hammer. Applicable for VW and AUDI FSI EN0364 3PCS Water Pump Tool Kit 1PC heated oxygen sensor socket 1/2 Dr. x 7/8" (22mm) x 50mm (L). 1PC vacuum switch socket 3/8 Dr. x 7/8 (22mm) x 30mm (L). 1PC vacuum switch socket 3/8 Dr. x 7/8 (22mm) x 6PT x 80mm (L). EN PCS Harmonic Balancer Puller Set 1PC 1/2 Dr. x 29mm x 6PT x 90mm (L). 1PC 3/8 Dr. x 7/8 x 6PT x 90mm (L). 1PC 3/8 Dr. x 7/8 x 6PT x 80mm (L). 1PC 1/2 Dr. x 7/8 x 50mm (L). 1PC 3/8 Dr. x 7/8 x 30mm (L). 1PC 1/2 Dr. x 27mm x 12PT x 78mm (L). 1PC 1/2 Dr. x 22mm x 12PT x 78mm (L). 1PC 1/2 Dr. x 22mm x 6PT x 110mm (L). 1PC 3/8 Dr. x 1 and 1-1/16 x 74mm (L). 1PC 1/2 Dr. x 28mm x 12PT x 78mm (L). EN0368 9PCS Injector Extractor Set Slotted sockets in 3/8 Dr. (10, 11, 12, 14mm ) and Material: Chrome Molybdenum with S45C steel. 1/2 Dr. (17, 19mm) x 6PT x 77mm(L). This set allows the crankshaft rotation on TDC-position and the For the assembly of top and side wired temperature sensors crankshaft counter hold, during the loosening of the crankshaft, thermo switches and other components. center screw or of the water pump toothed wheel fastening Also suitable for nuts and bolts of bent pipes. screw. The slot width is 7.4mm, 8.8mm, 9.1mm, 10.5mm, 13.3mm It is also suitable for removal or extraction of the water pump and 14.4mm. toothed wheel and water pump itself. On socket rail. Suitable for VW T5, Touareg 2.5L 5 cylinder TDI EN0367 5PCS Sensor Socket and Thread Chaser Kit 1PC heated oxygen sensor socket 1/2 Dr. x 7/8 (22mm) x 50mm (L). 1PC vacuum switch socket 3/8 Dr. x 7/8 (22mm) x 30mm (L). 1PC vacuum switch socket 3/8 Dr. 7/8 (22mm) x 6 PT x 80mm (L). 2PCS tapered 12mm and 18mm threads designed to start and remove carbon and dirt or straighten damaged threads in spark plug hole. Use with deep socket, open ends or boxes wrench. This device removes vibration dampers, balancers, pulleys and gears with tapped holes. Force is evenly distributed upon application. Puller can be used to pull out most objects since it works on either two or three tapped holes. Use with a wrench for more winding power. Applies to most foreign and import vehicles. 3PCS cap screw 3/8-24 x 2 (L). 3PCS cap screw 5/16-18 x 2 (L). 3PCS cap screw M8 x 1.25 P x 80mm (L). 3PCS cap screw 3/8-16 x 4 (L). 1PC 5/8 main center bolt. 1PC 4 slot yoke. 1PC pointed shaft protector. This high quality tooling is designed for the removal of stuck and seized injectors. Made by S45C steel. Total length 350mm (L) KGS slide hammer. M17 x 1.0 adaptor. M27 x 1.0 adaptor for Bosch injector nozzle. Puller w/m12 x 1.75 P adaptor. EN-28 EN-29

17 EN0370 8PCS Ford Diesel Engine Injection Timing Kit EN0382 Piston Ring Filer EN0377 6PCS Diesel Injector and Lambda Sensor Socket Set EN0376 PSA HDI Injection Nozzles Removal Set Applications: 1600cc and 1800cc diesel engines fitted to Ford Fiesta, Escort, Orion, P100, Sierra and Mondeo models. Also suitable for 2500cc DI engines on 1985 and later Ford Transit Vans and Galaxy 1900cc TD vehicles. EN PCS Glow Plug Removal Set By using the bracket the filer may be screwed to the work bench or can be held in a bench vise. To file piston rings. Lay the ring on top of the guide plate and against the tapered locators. Compress the ring to force the ends lightly against the sides of the cutting wheel. Turn the handle in the direction indicated be the arrow to produce a clean parallel cut. Applications: Hexagonal sockets for removal of the electrical solenoid from modern injectors. 1/2 Dr. x 78mm length. 25mm Hex-Siemens injectors as found on PSA, Ford, Toyota...etc. 27mm Hex-Siemens Piezo injectors as found on PSA etc. 29mm Hex-Bosch injectors. Applications: Complete set for removing PSA HDI BOSCH and SIEMENS injectors without dismounting the cylinder head. Equipped with a pulling easily remove injectors and a blower adapter to calm the injector seats. Engines: PSA 2.0,HDI, DW10 and DW12. EN PCS Glow Plug Removal Set EN0381 Universal Camshaft Pulley Holding Tool EN0380 4PCS Diesel Injector and Lambda Sensor Socket set Applications: Hexagonal sockets for removal of the electrical solenoid from modern injectors. 1PC Hex 12mm spindle, Hex30mm nut cone center tool. 1PC Drill installer. 2PCS 3-1/4-28 UNF, Hex 8mm. 2PCS diameter 6 mm x 3.5 x 40L. 1PC 3mm alley key. 1PC 9.7mm square socket. 1PC 7 x 5.5 drill. 1PC 9 x 5.5 drill. 1PC T-handle. 2PCS diameter 3.5 drill 2pcs. 1PC M10 x P10 tap. 1PC M8 1.0 tap. 1PC 13-1/4-28UNF tap. 1PC 8 x 5.5 drill. 1PC M12 x 1.25P tap. 1PC 10.8 x 5.5 tap. 1PC Hex 12mm spindle, Hex30mm nut cone center tool. 1PC Drill installer. 2PCS 3-1/4-28 UNF, Hex 8mm. 2PCS diameter 6 mm x 3.5 x 40L. 1PC 3mm alley key. 1PC 9.7mm square socket. 1PC 7 x 5.5 drill. 1PC 9 x 5.5 drill. 1PC T-handle. 2PCS diameter 3.5 drill 2pcs. 1PC M10 x P10 tap. 1PC M8 1.0 tap. 1PC 13-1/4-28UNF tap. Pin size: 5, 6, 8, 10mm. 1/2 Dr. 78mm length. 25mm Hex-Siemens injectors as found on PSA, Ford, Toyota etc. 27mm Hex-Siemens Piezo injectors as found on PSA etc. 29mm Hex-Bosch injectors. 30mm Hex-Bosch injectors. EN-30 EN-31