High Ohmic / High Voltage Metal Glaze Leaded Resistors

Transcription

1 High Ohmic / High Voltage Metal Glaze Leaded Resistors A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps. The resistors are coated with a light blue lacquer which provides electrical, mechanical, and climatic protection. FEATURES UL Approved (UL1676, file no: E17116) Meet the safety requirements of: - IEC 66 - EN 66 - VDE 86 - CQC (China) AEC-Q qualified ( only) High pulse loading capability (maximum kv) Radial version available for Material categorization: for definitions of compliance please see APPLICATIONS Where high resistance, high stability, and high reliability at high voltage are required High humidity environment White goods Power supplies TECHNICAL SPECIFICATIONS DESCRIPTION Imperial size Resistance range (1) k to 22 M k to 33 M k to 68 M Resistance tolerance ± %; ± %; ± 1 % Temperature coefficient ± ppm/k Rated dissipation, P 7.2 W. W 1. W Operating voltage, U max. AC/DC 16 V 3 V V Operating temperature range - C to +1 C Peak permissible film temperature 1 C Thermal resistance (R th ) 14 K/W 1 K/W 7 K/W Insulation voltage: 1 min.; U ins 7 V Maximum noise (white noise) μv/v 2. μv/v 2. μv/v Max. resistance change at rated dissipation for resistance range, R/R max., after h 1. % 1. % 1. % Note (1) Ohmic values (other than resistance range) are available on request. SAFETY REQUIREMENTS AND QUALIFICATIONS DESCRIPTION Safety requirements / qualifications AEC-Q UL1676 qualification (file no: E17116) for ohmic range k to 11 M; DIN EN 66 safety requirements as per clause 14.1 a); IEC 66 safety requirements as per clause 14.2; VDE 86 as per clause 14.1 a); CQC Revision: 2-Sep-1 1 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

2 TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE TCR TOLERANCE RESISTANCE E-SERIES ± 1 % k to 1 M E24; E96 ± % k to 22 M E24; E96 ± % 1 M to 22 M E24 ± ppm/k ± 1 % k to 33 M E24; E96 ± % k to 33 M E24 ± 1 % k to 68 M E24; E96 ± % k to 68 M E24 PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: 3FA V R F A 1 TYPE / SIZE VARIANT TCR RESISTANCE TOLERANCE (1) PACKAGING SPECIAL = = = = neutral = standard 3 digit value 1 digit multiplier MULTIPLIER = * 1 = * 1 2 = * 2 3 = * 3 4 = * 4 = * 6 = * 6 F = ± 1 % J = ± % K = ± % PRODUCT DESCRIPTION: 1 % A1 K 1 % A1 K A1 AC A RD R N4 = standard TYPE / SIZE TOLERANCE PACKAGING RESISTANCE ± 1 % ± % ± % Note (1) See table Temperature Coefficient and Resistance Range for selecting correct ohmic value - tolerance combination. A1 AC A RD R N4 K = k 1M = 1 M PACKAGING TYPE CODE QUANTITY PACKAGING STYLE WIDTH PITCH DIMENSIONS A1 3 mm mm 7 mm x 31 mm x 26 mm Taped according to IEC fan-folded in a box A 3 mm mm 76 mm x mm x 26 mm N4 4 Taped according to IEC fan-folded in a box mm 48 mm x 23 mm x 33 mm R Taped according to IEC on a reel 3 mm mm 93 mm x 3 mm x 298 mm A1 Taped according to IEC fan-folded in a box 3 mm mm 72 mm x 6 mm x 28 mm R Taped according to IEC on a reel 3 mm mm 9 mm x 37 mm x 37 mm AC Taped according to IEC fan-folded in a box 66 mm mm 82 mm x 111 mm x 26 mm RD 7 Taped according to IEC on a reel 66 mm mm mm x 31 mm x 3 mm Revision: 2-Sep-1 2 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

3 DESCRIPTION Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a high grade ceramic body and conditioned to achieve the desired temperature coefficient. Plated steel termination caps are firmly pressed on the metalized rods. Mostly, a special laser is used to achieve the target value by smoothly cutting a helical groove in the resistive layer without damaging the ceramics. Connecting wires of electrolytic copper plated with % pure tin are welded to the termination caps. The resistor elements are covered by a light blue protective coating designed for electrical, mechanical, and climatic protection. Four or five color code rings designate the resistance value and tolerance in accordance with IEC 662. Yellow and gray are used instead of gold and silver because metal particles in the lacquer could affect high-voltage properties. The result of the determined production is verified by an extensive testing procedure performed on % of the individual resistors. Only accepted products are stuck directly on the adhesive tapes in accordance with IEC or for the radial versions in accordance to IEC MATERIALS Vishay acknowledges the following systems for the regulation of hazardous substances: IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (1) The Global Automotive Declarable Substance List (GADSL) (2) The REACH regulation (197/6/EC) and the related list of substances with very high concern (SVHC) (3) for its supply chain The products do not contain any of the banned substances as per IEC 62474, GADSL, or the SVHC list, see Hence the products fully comply with the following directives: /3/EC End-of-Life Vehicle Directive (ELV) and Annex II (ELV II) 11/6/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment 1/863/EU 12/19/EU Waste Electrical and Electronic Equipment Directive (WEEE) Vishay pursues the elimination of conflict minerals from its supply chain, see the Conflict Minerals Policy at ASSEMBLY The resistors are suitable for processing on automatic insertion equipment and cutting and bending machines. Excellent solderability is proven, even after extended storage. They are suitable for automatic soldering using wave or dipping. The resistors are completely lead (Pb)-free, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. The immunity of the plating against tin whisker growth, in compliance with IEC , has been proven under extensive testing. The encapsulant is resistant to cleaning solvent specified in IEC The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. APPROVALS These resistors meet the safety requirements of: UL1676 ( k to 11 M); file no: E17116 IEC 66, clause 14.2 DIN EN 66, clause 14.1.a) VDE 86, clause 14.1.a) CQC, China RELATED PRODUCTS For a correlated range of Metal Film Resistors see the datasheet: High Ohmic / High Voltage Metal Film Leaded Resistors, For product that offers high power dissipation and metal oxide film technology see the datasheet: High Power Metal Oxide Leaded Resistors, Notes (1) The IEC list of declarable substances is maintained in a dedicated database, which is available at (2) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council, and available at (3) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at Revision: 2-Sep-1 3 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

4 FUNCTIONAL PERFORMANCE Derating Power in % Ambient Temperature in C Hot-Spot Temperature Rise (T) as a Function of Dissipated Power Revision: 2-Sep-1 4 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

5 Maximum allowed peak pulse voltage in accordance with IEC 66, 14.2; discharges from a 1nF capacitor charged to Û max. ; 12 discharges/min (drift R/R 2 %) Ûmax. (kv) R n (MΩ) 2 11 Ûmax. (kv) R n (MΩ) 2 Ûmax. 11 (kv) R n (MΩ) 2 Revision: 2-Sep-1 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

6 Temperature Rise (T) at the Lead End (Soldering Point) as a Function of Dissipated Power at Various Lead Lengths after Mounting mm mm 1 mm mm mm 1 mm mm 3 1 mm Revision: 2-Sep-1 6 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

7 TESTS PROCEDURES AND REQUIREMENTS All tests are carried out in accordance with the following specifications: IEC 611-1, generic specification (includes tests) The test and requirements table contains only the most important tests. For the full test schedule refer to the documents listed above. The tests are carried out with reference to IEC 611-1, in accordance with IEC xx test method and under standard atmospheric conditions in accordance with IEC 668-1,.3. A climatic category / 1 / 6 is applied, defined by the lower category temperature (LCT = - C), the upper category temperature (UCT = 1 C), and the duration of exposure in the damp heat, steady state test (6 days). Unless otherwise specified the following values apply: Temperature: 1 C to 3 C Relative humidity: 4 % to 7 % Air pressure: 86 kpa to 6 kpa (86 mbar to 6 mbar). For performing some of the tests, the components are mounted on a test board in accordance with IEC 611-1, In test procedures and requirements table, only the tests and requirements are listed with reference to the relevant clauses of IEC and IEC xx test methods. A short description of the test procedure is also given. TESTS PROCEDURES AND REQUIREMENTS IEC CLAUSE IEC TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R max. ) Insulation resistance U max. DC = V during 1 min; V-block method R ins min.: M 4.7 Voltage proof U RMS = U ins ; 6 s No breakdown or flashover 4.8 Temperature coefficient At ( / - / ) C and ( / 1 / ) C ± ppm/k 4.12 Noise IEC Short time overload (Ua1) 21 (Ub) 21 (Uc) Robustness of terminations 4.17 (Ta) Solderability 4.18 (Tb) (Na) Resistance to soldering heat Rapid change of temperature Room temperature; 2. x P 7 x R ; (voltage not more than 2 x limiting voltage); cycles; s ON and 4 s OFF Tensile, bending, and torsion +23 C; 2 s; solder bath method; SnPb4 +24 C; 3 s; solder bath method; SnAg3Cu. (before aging) +23 C; 2 s; solder bath method; SnPb4 +24 C; 3 s; solder bath method; SnAg3Cu. (after aging) Unmounted components (26 ± ) C; ( ± 1) s 3 min at - C and 3 min at +1 C; cycles (Eb) Bump 3 x 1 bumps in 3 directions; 4 g (Fc) Vibration 4.23 Climatic sequence: (Bb) Dry heat 16 h; 1 C (Db) Damp heat cyclic : max. μv/v : max. 2. μv/v : max. 2. μv/v R max.: ± 2 % R No damage R max.: ±. % R Good tinning ( 9 % covered); no damage Good tinning ( 9 % covered); no damage R max.: ±. % R R max.: ±. % R No damage R max.: ±. % R sweep cycles per direction; Hz to Hz; 1. mm or m/s 2 No damage R max.: ±. % R 24 h; 2 C to C; 9 % to % RH (Ab) Cold 2 h; - C (M) Low air pressure (Db) Damp heat remaining cyclic 2 h; 8. kpa; 1 C to 3 C days; C; 9 % to % RH; cycles DC load Apply rated power for 1 min R ins min.: 1 G R max.: ± 1. % R Revision: 2-Sep-1 7 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

8 TESTS PROCEDURES AND REQUIREMENTS IEC CLAUSE (Cab) Damp heat (steady state) Endurance (at 7 C) IEC TEST METHOD TEST Active flammability cheese-cloth test Passive flammability needle-flame test PROCEDURE 6 days; 4 C; 9 % to 9 % RH; loaded with.1 P 7 (steps: V to V) h; loaded with P 7 or U max. ; 1. h ON and. h OFF Steps of: / / 16 / 2 / 4 x P 7 duration min Application of test flame for s REQUIREMENTS PERMISSIBLE CHANGE (R max. ) R max.: ± 1. % R R max.: ± 1. % R : no flaming of gauze cylinder : no flaming of gauze cylinder No ignition of product; no ignition of under-layer; burning time less than 3 s DIMENSIONS D d L 1 L 2 DIMENSIONS - Leaded resistor types, mass, and relevant physical dimensions TYPE Ø D max. (mm) L 1 max. (mm) L 2 max. (mm) Ø d (mm) MASS (mg) ± ± ±. 169 WITH RADIAL TAPING Lead Spacing (F = 4.8 mm), Size 7 H 1 H H L L 1 P 2 P W W DIMENSIONS in millimeters Pitch of components P 12.7 ± 1. Lead spacing F / -. Width of carrier tape W 18. ±. Body to hole center H 19. ± 1. Height for cutting (max.) L 11 Height for bending H 16. ±. Component height (max.) H 1 29 α α F P P 1 D α = 3 to 4 a a Revision: 2-Sep-1 8 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

9 HISTORICAL 12NC INFORMATION The resistors have a 12-digit numeric code starting with refers to refers to refers to The subsequent first digit for 1 % tolerance products (E24 and E96 series) or 2 digits for % (E24 series) and % (E12 series) indicate the resistor type and packing The remaining digits indicate the resistance value: - The first 3 digits for 1 % or 2 digits for % and % tolerance products indicate the resistance value - The last digit indicates the resistance decade Last Digit of 12NC Indicating Resistance Decade RESISTANCE DECADE LAST DIGIT k to 976 k 4 1 M to 9.76 M M 6 Historical 12NC Example The 12NC for a, resistor value 7. M, % tolerance, supplied on a bandoleer of units in ammopack, is: The 12NC for a, resistor value 7. M, % tolerance, supplied on a bandoleer of units in ammopack, is: The 12NC for a, resistor value 7. M, % tolerance, supplied on a bandoleer of units in ammopack, is: NC CODING FOR - Resistor type and packaging TYPE TOLERANCE (%) RADIAL TAPED 4 UNITS CODING STARTS WITH CODING STARTS WITH CODING STARTS WITH BANDOLIER IN AMMOPACK STRAIGHT LEADS BANDOLIER ON REEL 2 mm 2 mm 66.7 mm 2 mm 66.7 mm UNITS UNITS UNITS UNITS 7 UNITS ± ± ± ± ± ± ± Revision: 2-Sep-1 9 Document Number: 2897 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

10 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Revision: 13-Jun-16 1 Document Number: 9