Maintenance and Instruction Manual. December 2011 Rev. 01 Page 1 of 12

Transcription

1 Maintenance and Instruction Manual December 2011 Rev. 01 Page 1 of 12

2 Table of Contents 1. Description of product and function 1.1 The NOREVA non-return valve range 1.2 Correct use 1.3 Transport and storage 1.4 Installation in the pipeline - Assembly 2. Servicing and maintenance 2.1 Servicing and maintenance 2.2 Spare parts 2.3 Replacement of spare parts Disassembly of Non-Return valve NRV-Z /ZK / ZSK / K Assembly of Non-Return valve NRV-Z /ZK / ZSK / K Disassembly of Non-Return valve NRV-B / BK Assembly of Non-Return NRV-B / BK 2.4 Incident during operation / Corrective action NOREVA GmbH Hocksteiner Weg 56 D Mönchengladbach Tel.: +49(0) Fax: +49(0) /66 info@noreva.de Internet: December 2011 Rev. 01 Page 2 of 12

3 1. Description of product and function Non-return valves are used wherever reverse flow of the conveyed fluid is to be prevented. They are suitable for all liquid and gaseous media and are heat-resistant thanks to the exclusive use of metal materials and non-corroding internal components. NOREVA non-return valves are produced in conformity to PED/97/23/EC and are tested at the manufacturer's works in accordance with DIN EN for mechanical strength and tightness. ATEX Directive 94/9/EC does not apply to NOREVA non-return valves. Typical applications include, for example, oil pipelines, iron and steel plants, chemicals plants, water recovery, pumping stations, water distribution systems, power generation plants, gas compressor stations, seawater desalination plants, etc. These valves provide smooth and shock-free closure within fractions of a second thanks to their short closure paths and low moving masses. CAUTION!!! Hot fluids present a danger of burns, customers must thermally insulate valves! 1.1 The NOREVA Non-return valve range Our range of products can be found in our catalogue and on our Internet site December 2011 Rev. 01 Page 3 of 12

4 1.2 Correct use Thanks to their design and construction, NOREVA non-return valves are used in the most diverse range of industries. NOREVA-non-return valves are designed for following application: Ambient temperature: -50 C to +50 C Admissible working temperature: -196 C to +500 C The operating data can be taken from the name plate for specific application. Our non-return valves are produced specifically in accordance with the customer's specifications and for his application, and may be used only for this purpose. Use for other operating data and/or for installation locations or services is not permissible without the manufacturer's agreement. The operator/user must implement provisions to eliminate valve flutter during operation. The conveyed fluid or gaseous media must be at a temperature not less than 20% remote from its auto ignition temperature. 1.3 Transport and storage Valves must not be suspended using lifting tackle (S-hooks) inserted into the flange borings, nor may they be rolled on the flanges, since both methods will damage the corrosion protection. A non-return valve with no suspension lugs must be handled and transported using belts slung around both flange necks and attached to the lifting equipment. The valves can also be equipped with threaded holes (for ring-bolts) and/or suspension lugs for the purpose of handling and transportation. Figure 1 December 2011 Rev. 01 Page 4 of 12

5 The non-return valve must be secured for transportation on a wooden pallet using wood packing and fixing straps. The stability of the non-return valves during transportation and storage must be ensured by positioning the valves on their flanges. The direction-of-flow arrow must always point upward. Wood beams Fixing tape Wooden pallet Figure 2 December 2011 Rev. 01 Page 5 of 12

6 1.4 Installation in the pipeline - Assembly Remove the packaging materials. The pipeline must be examined for fouling and foreign bodies prior to installation and cleaned if necessary. Danger of injury!! The applicable safety regulations in accordance with VGB 9a must be adhered to. The necessary personal safety equipment/clothing must be used. Attention! Note the direction of flow as indicated by the cast-on arrow on the housing and the arrow on the name plate! The name plate is always fitted to the exit flange/exit side. Cast inscription Figure 3 Flow direction Figure 4 December 2011 Rev. 01 Page 6 of 12

7 The counter flanges on the pipeline must be plan-parallel and concentric. The connecting bolts must be tightened uniformly (avoiding distortion) and in crosswise alternating order. The pipeline must under no circumstances be pulled toward the valve to close the joint. There should be sufficient space between the pipe flanges during installation of the valve, in order to avoid damage to the flanges and in order that gaskets can be installed. Installation immediately downstream bends, T-joints or dampers and/or control valves should be avoided wherever possible. Any unusual installation situations should be discussed and agreed with NOREVA. Flow direction Pump Noreva non return valve Figure 5 Noreva no-return valve Noreva non-return valve Figure 6 Figure 7 December 2011 Rev. 01 Page 7 of 12

8 2. Servicing and maintenance Inspection and servicing/maintenance work may be performed only once the section of pipe in which the valve is installed has been isolated, depressurized and secured against reactivation. CAUTION Caution All pressure-conducting lines must be depressurized and secured against reactivation before starting any servicing / maintenance work. All joints and connections must be checked for tightness and firm seating when the servicing /maintenance work has been completed. DANGER In case of escape of hazardous liquids, substances, gases and fumes/vapors, shut the system down immediately, inform the responsible supervisor and perform the corresponding repair work. Danger Personal safety equipment and clothing in accordance with the regulations issued by the professional associations must be used. There is a danger, depending on the medium conducted, of poisoning, corrosive burns, scalding, and also dangers arising from biological and microbiological substances and from fire and potential explosion. December 2011 Rev. 01 Page 8 of 12

9 2.1 Servicing and maintenance NOREVA non-return valves require no servicing or maintenance. The following checks within the scope of the standard servicing and maintenance intervals for the overall system are nonetheless recommended: Check of external leakage Check for damage Check for fouling/freedom of movement Check of unusual noises 2.2 Spare parts The valve serial number should always be stated when ordering spare parts. This serial number can be found on the name plate (Figure 4) and on the valve flange. 2.3 Replacement of spare parts The valves must be removed from the pipeline after depressurization of the line in order to replace parts. Repair work on NOREVA non-return valves may be performed only by NOREVA or by persons trained and approved by NOREVA. December 2011 Rev. 01 Page 9 of 12

10 2.3.1 Disassembly of non return valve NRV-Z / ZK / ZSK / K (Figure 8/8.1) In case of malfunctioning of a valve, remove the valve from the pipeline and firstly inspect the seat (2) and valve disk (3) for damage, and remove any foreign bodies found. IMPORTANT: DANGER OF CRUSHING!! If this does not eliminate the problem, the nozzle/guide (5) must be pulled or pushed out of its seating in the direction of flow. Any grub screws used to secure the nozzle/guide must be removed prior to dismantling. Any damage present can then be ascertained and parts replaced if necessary. A new valve disk (3) must be ground against the seat (2) using a device (specific Noreva tool) and grinding paste during installation Assembly of non return valve NRV-Z / ZK / ZSK / K (Figure 8/8.1) The nozzle (5) should first be positioned on its rib and the spring (4) and valve disk (3) then installed; then slip the housing (1) over the nozzle (5) and press or beat the collar of the nozzle into the housing seating using a suitable plate. If the nozzle/guide was secured using grub screws, new threaded holes must be made and new grub screws installed. The grub screws should be secured using hardening adhesive (e.g. DELO 5298). Valve functioning has now been restored, and the valve can be re-installed. Our specialist technicians will be glad to assist with advice. Repairs can also be performed at short notice at our works. open Flow direction closed open Flow direction closed Grub screw Figure 8 Figure 8.1 December 2011 Rev. 01 Page 10 of 12

11 2.3.3 Disassembly of non retrun valve NRV-B / BK (Figure 9) In case of malfunctioning of a valve, remove the valve from the pipeline and firstly inspect the seat (2) and valve disk (4) for damage, and remove any foreign bodies found. IMPORTANT: DANGER OF CRUSHING!! If the above does not solve the problem, firstly remove the central bolt (8). Then lift out the nozzle ring (3) using the holes provided for this purpose. It must be ensured that the valve disk (4), which is not fixed to the nozzle ring (3) but instead only guided by the guide mechanisms (6) remains in the housing (1). Any damage present can then be ascertained and parts replaced if necessary. Ensure correct location of the springs (5) between the guide mechanisms (6) and the nozzle ring (3). A new valve disk (3) must be ground against the seat (2) using a device and grinding paste during installation Assembly of non return valve NRV-B / BK (Figure 9) The guide mechanisms must engage uniformly in the disk collar when the nozzle ring (3) is positioned on the valve disk (4). Tie the valve disk (4) and nozzle ring (3) together using not less than two plastic tapes and insert them into the housing (1). Then remove the tapes and screw in the central bolt (8). The central bolt must be secured using hardening adhesive (DELO 5298). Tightening torque for central bolts out of material 42CrMo4V: M24 = 350 Nm M36 = 1150 Nm M52 = 3500 Nm M72x6 = Nm M27 = 500 Nm M45 = 2250 Nm M56 = 4350 Nm M30 = 650 Nm M48 = 2700 Nm M64 = 6456 Nm open Flow direction Figure 9 closed December 2011 Rev. 01 Page 11 of 12

12 Valve functioning has now been restored, and the valve can be re-installed. Our specialist technicians will be glad to assist with advice. Repairs can also be performed at short notice at our works. 2.4 Incident during operation / Corrective action Problem Possible cause Correction Leakage at the valve seat NRV incorrectly installed Depositions/fouling on the seat Pump delivering against closed non-return valve. Clean valve seat and disk. Note Section 2. Install non-return valve in accordance with Section 1.4 December 2011 Rev. 01 Page 12 of 12