Superstrut. Metal Framing. Table of Contents

Transcription

1 Table of Contents Finishes and Materials...A2 Channels and Concrete Inserts...A3 A7 Threaded Products and Hardware...A8 A12 Fittings and Brackets...A13 A23 Beam Clamps... A24 A32 Pipe Straps, Pipe Clamps and Hangers... A33 A46 Hanger Accessories... A47 Surface Raceway and Lighting Systems... A48 A54 Right Angle Slotted... A55 A56 Engineering Data & Specifications...A57 A73 A1

2 Finishes and Materials Finishes on Steel Bare (Suffix BC) Pregalvanized (Suffix PGC) A zinc coating is applied to the steel coil at the mill prior to fabrication. Once the ma te ri al is worked by rollform ing, cutting, or punching, minimal pro tec tion is pro vid ed for raw edges. This weak ness is typical with precoated ma te ri al and af fects the channel section around holes, extreme ends, and the edges of the Ushape lips. Superstrut pre galvanized material is in con form ance with ASTMA525/G90 spec i fi ca tion standards, re pre sent ing 0.90 oz. of zinc per square foot of steel. This finish is often referred to as mill galvanized. Electrogalvanized (Suffix EGC) Often referred to as zinc plated or elec tro plat ed zinc, the steel and 0.5 mils of zinc are bonded by an elec tro ly sis process. Electrogalvanizing is most com mon ly applied to small fittings, hardware, and thread ed products. Special Materials Aluminum (Suffix ALC) Superstrut channel is available in aluminum. Fittings in HDG finish or fiberglass material are suggested for fastening products. Stainless Steel (Suffix SS) Superstrut channel is supplied in Type 316 (T316L) stainless steel. All fittings and accessories are in 316SS (SS6). Contact your Regional Sales Office for availability. Thomas & Betts reserves the right to change ma te ri al and finish spec i fica tions without notice, to improve its prod ucts. GoldGalv (No Suffix) Gold coloured zinc dichromate is applied over the zinc, pro duc ing a chemically bonded non porous barrier for pro tec tion from mois ture and air. This extends the protective life of the zinc, and pro vides an excellent base for paint, if desired. The GoldGalv hardware finish also provides a low elec tri cal resistance when grounding of the system is required. Superstrut channel and fittings are plated after fabrication, so there are no un pro tect ed edges from cutting or punch ing. Where field cutting is necessary or scratches occur due to con struc tion handling, you still have the sacrificial protection of the plated zinc to minimize the corrosion of raw edges and pre vent spreading. HotDipped Galvanized (Suffix HDGC) The material is zinc coated after fab ri ca tion providing total product pro tec tion on all surfaces. The fab ri cat ed chan nel or fitting is sus pend ed and then dipped into tanks of hot zinc for a prolonged period, creating a co her ent bond. The result is superior cor ro sion resistance as compared to pregalvanized material. Hotdipped galvanizing is not rec om mend ed for thread ed pro ducts, considering the zinc coating thick ness will often disrupt the threads. Superstrut hotdipped galvanized is in conformance with ASTM Spec i fi ca tions A123 (for mer ly A386) and A153. Superstrut chan nels maintain a min i mum 1.5 oz. of zinc per square foot of steel or 2.5 mils (ASTM A123, Thick ness Grade 65). This finish is also referred to as Hotdipped galvanized after fabrication. Epoxy Powder Coated Green, Grey or White (Suffix GR, GY or WH) Epoxy powder resins are applied elec tro stat i cal ly to the steel after fab ri cation. Once the material is com plete ly covered with the powderform epoxy, it proceeds through a 400 F (204 C) ba king process for ten minutes, cre at ing a chemical bond. This re sults in a minimum of 1.5 mil thick ness of epoxy coating pro vid ing excellent re sis tance to chipping or peeling. A2

3 Channels and Concrete Inserts Channels Material Steel channels are coldroll formed from strip steel. Aluminum and Fiberglass channels are extruded profiles. Material Thickness All Series gauge material All Series gauge material All Series gauge ribbed material Standard Lengths Standard lengths for channels are 10 ft. and 20 ft. with a tolerance of +1/8 in. Special lengths can be requested; however, minimum quantities may apply. Channels are sold per foot. Warning Load tables, charts, and de sign criteria provided in this catalogue are intended as guides only. Se lec tion of pro per product, support spacing, erec tion, and place ment are the responsibility of the user. When im prop er ly used as tools of erection, pipe hanger products have oc ca sio nal ly failed. To avoid an accident, the user is cau tioned to use the product only as it was intended. Concrete Inserts Material Superstrut continuous insert channel is manufactured from 12 gauge hot rolled strip steel in two basic sizes as follows: A302 15/8 in. x 15/8 in. 7/8 in. slot C302 15/8 in. x 13/8 in. 7/8 in. slot Standard Lengths Standard lengths are 10 ft. and 20 ft. Product is sup plied with foam filler and end caps to prevent concrete from seeping into channel. Application For casting into concrete walls, floors or ceilings to pro vide for attachment anywhere along the continuous slot. Design Data Load ratings as shown have a safety factor of 3 in 3000 lb. hard rock concrete. Where sound concrete does not exist, the load ratings shall not apply. GoldGalv hardware finish is standard for all Superstrut Concrete insert prod ucts. This is a multiprocess finish of electroplated zinc, followed by gold coloured zinc dichro mate to give ex cel lent corrosion resistance and a superior paint base. For more information on load design, see page A57 for Engineering Data and Specifications. A3

4 Channels and Concrete Inserts Channels at Full Scale Available in 10 and 20 foot length 1 5 /8 7 /8 1 5 /8 1 5 /8 7 /8 7 /8 1 5 /8 A Series 1 5 /8 AR Series 27/16 E Series A gauge A gauge 16 gauge only E gauge 1 5 /8 1 5 /8 1 5 /8 7 /8 7 /8 7 /8 1 3 /16 B Series 1 3 /16 BR Series B gauge B gauge 16 gauge only 1 5 /8 7 /8 1 5 /8 3 1 /4 H Series 7 /8 1 3 /8 C Series 1 D Series C gauge D gauge H gauge A4

5 Channels and Concrete Inserts Channel Selection Chart CHANNEL HOLE CONFIGURATIONS LENGTH FINISH ON STEEL SPECIAL MATERIALS Series HS S SW P KO ft. B(C) PG(C) EG(C) GoldGalv HDG(C) GR(C),GY(C),WH(C) AL(C) T316L SS6(C) A or 20 A or 20 AR or 20 B or 20 B or 20 BR or 20 C or 20 D or 20 E or 20 H or 20 Legend EXAMPLES HOLE CONFIGURATION FINISH ON STEEL SPECIAL MATERIALS A120010PG Plain channel, 10 ft., pregalvanized finish Suffix blank HS Plain, no holes Half slot Suffix BC PGC Bare Pregalvanized Suffix AL SS6 (C) Aluminum Stainless Steel Type 316 B1400P10 Punched channel, 10 ft., GoldGalv finish E1200HS20HDG Half slot channel, 20 ft. hot dipped galvanized S Slotted EGC Electrogalvanized T316L Stainless Steel Type 316L SW Slotted wide Blank GoldGalv P Punched HDGC Hot dipped galvanized KO Knockout GR,GY,WH Epoxy paint in green (GR), grey (GY), or white (WH) Standard offering A minimum order quantity may apply Hole Configuration Half Slot Channel Slotted Channel SW Slotted Wide Channel Punched Channel Channel with Knockouts /8 6 Slots: 9/16 in. X 11/8 in. Slots: 7/16 in. X 3 in. Slots: 9/16 in. X 3 in. Holes: 9/16 in. KO: 1/2 in. A5

6 Channels and Concrete Inserts Welded Combinations 02 02A 02B 02C 03A 03B EXAMPLES Two A1200 chan nels back to back are ordered as A1202. Two A1200 channels back to side are ordered as A1202C. 03C 03D 03E 04 Back to back steel channel is riveted at every 4 inches. Aluminum back to back channel are extruded profiles. All other combinations are spot welded at every 4 inches. E and H series are not available in triple and quadruple. End Caps and Closure Strips A804 End Cap RAWSEC End Cap for D1200 Channel A2431EGC End Cap A208 For Channel Wt./C lb. A804EG A A1400 AR B804EG B1400 BR C804EG C E804EG E H804 H RAWSEC D g (0.18 oz) Safety End Cap 15/8 in. x 15/8 in. White Plas ti sol For Channel Wt./C lb. A804NEOPWH A1200 AR A1400 B804NEOPWH B1200 BR H804NEOPWH H A213 Inside Joiner For A1200 Channel Wt./C 16 lb. A208HDGC A208EG Does not include stud nut or bolts. A208 A208SS6C For A and AR Series channel. Wt./C 275 lb. For A1200 Series only. Available only in GoldGalv finish. AB844PGC PreGalvanized Closure Strip For all channel. Standard lenghts 10 ft. AB844PCGY Plastic Closure Strip Colour: Grey AB844PC Plastic Closure Strip Colour: Gold A6

7 Channels and Concrete Inserts Concrete inserts Concrete Channel Inserts Anchor Caps 46010TB Removable Plastic Closure Strip *Finishes HDGC GoldGalv PGC 4 *Finishes EGC GoldGalv Insert with end caps and foam closure strip installed. Length (ft.) Gauge Wt. (lb./ft.) A30210* A30220* B30210* B30220* Design Load 2000 lb. per foot in hard rock concrete with a safety factor of 3. Standard lengths: 10 ft. and 20 ft. Length tolerance: 3/16 in. 12 gauge, Wt./C: 30 lb./c A450* For A Series C450* For C Series From pieces of A, B, C channel and a pair of anchor caps, short concrete inserts can be fabricated in the field. Designed as an added precaution to keep insert free of concrete. Closure strip fits all 15/8 in. wide strip inserts, regardless of depth. Order per 10 foot, standard length is 10 ft. Material Black Plastic Wt./C 52 lb. SI400 Spot Insert Kit STD. PACK TB Spot Insert Thred O.D. Wt./C size Insert lb. SI4003/8 3/8 16 2x5/8 10 SI4001/2 1/2x13x11/4 21/2x7/8 35 Other sizes available. Maximum recommended load: SI4003/8 = 450 lb./204 kg SI4001/2 = 1000 lb./454 kg Standard Finish GoldGalv An insert with a knockout saves covering the opening. Ac com mo dates hanger rod sizes from 1/4 in. through 7/8 in. by means of an AB102 insert nut, to be ordered separately. Design load: 1350 lb. in 3000 lb. hard rock concrete with a safety factor of 3. Complies with Specification MSS SP69, Type 18. A7

8 Threaded Products and Hardware Channel Nuts Superstrut channel nuts are manufactured from Grade 2 mild steel and are case hardened. Design Data Superstrut self aligning channel nuts are designed to provide resistance to pullout and resistance to side slip in excess of the full strength of the channels with which they are used. The extreme resistance to side slip results from the unique design of the alternate teeth, spaced and designed to develop a wedging action that increases with pressure or load. Screw Threads All threaded products are American Standard thread, free fit class 2. Thread Size 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 Threads per inch Design Torque (ft.lb.) Finish and special materials Standard finish for all hardware is Electrogalvanized (EGC) or GoldGalv. Stainless Steel Type 316 is also available. Contact your Regional Sales Office for availability and minimum quantities. Spring Nut Selector Chart SPRING NUT A1001/4EGC A1005/16EGC A1003/8EGC A1001/2EGC A1003/4 B1001/4EGC B1005/16EGC B1003/8EGC B1001/2EGC H1003/8EGC H1001/2EGC CM1001/4 CM1003/8 CM1001/2 CM1001/2B UC1001/4 UC1003/8 UC1001/2 CHANNEL SERIES A AR B BR C D E H A8

9 Threaded Products and Hardware A100 Regular Spring Nut* STD. PACK 100 B100 Short Spring Nut* STD. PACK 100 H100 Long Spring Nut* STD. PACK 100 Available in Stainless Steel 316. Nut is square over 1/2 in. size. For all A and C Series channel and inserts. Size Wt./C lb. A1001/4EGC 1/4 8 A1005/16EGC 5/16 9 A1003/8EGC 3/8 10 A1001/2EGC 1/2 12 A1005/8EGC 5/8 19 A1003/4 3/4 19 A1007/8 7/8 18 AB100 Springless Nut 1/4 in. thick STD. PACK 100 AC100 Springless Nut Heavy duty 3/8 in. thick Size Wt./C lb. B1001/4EGC 1/4 7 B1005/16EGC 5/16 8 B1003/8EGC 3/8 9 B1001/2EGC 1/2 9 Available in Stainless Steel 316. For all B and D Series channel and inserts. STD. PACK 100 For all E and H Series channel and inserts. 813EG Springless Nut Light Duty Size Wt./C lb. H1003/8EGC 3/8 10 H1001/2EGC 1/2 14 STD. PACK 100 For use with all channels. Nut is square over 1/2 in. size. Size Wt./C lb. AB1001/4EGC 1/4 7 AB1005/16EGC 5/16 8 AB1003/8EGC 3/8 9 AB1001/2EG 1/2 9 AB1005/8EG 5/8 10 AB1003/4EG 3/4 10 A182 to A185 Regular Spring Stud Nut* STD. PACK 100 Size Wt./C lb. AC1003/8EGC 3/8 9 AC1001/2EGC 1/2 11 AC1005/8EGC 5/8 18 AC1003/4EGC 3/4 18 For all A, C, E and H Series channel and inserts. Nut is square over 1/2 in. size. A177 to A179 Springless Stud Nut STD. PACK 100 For use with all channels. 812 Stud Nut Size Wt./C lb. 813EG 1/4 5 STD. PACK 100 For all A and C Series channels. E145 Standard Hex Nut Bolt Dia Length A Wt./ C lb. A1821/4x100EG 1/ A1821/4x125EG 1/4 11/4 15 A1843/8x100EG 3/ A1843/8x125EG 3/8 11/4 15 A1851/2x100EG 1/ A1851/2x125EG 1/2 11/4 15 STD. PACK 100 For use with all channels. Bolt Dia Length Wt./ A C lb. A1771/4x100EG 1/4 1 8 A1771/4x125EG 1/4 11/4 10 A1793/8x100EG 3/ A1793/8x125EG 3/8 11/ UCN Universal Nylon Cone Nut STD. PACK 100 AB102 Unhardened Square Nut For Channel Wt./C lb. 8121EG 1/4 x 1 6 For attaching fixture to channel slot down or to channel slot up knockouts. Specify length. Hex nut included. STD. PACK 100 Size Wt./C lb. E1451/4EGC 1/4.72 E1453/8EGC 3/ E1451/2EGC 1/ E1455/8EG 5/ E1453/4EGC 3/ E1457/8EGC 7/ E1451EGC GoldGalv only For all 15/8 in. and 11/2 in. channels. May be used with ALL Strut Depths. Can be used for A100 Series, B100 Series and AB100 Series. ES145 Swivel Nut and Jam Nut Combinations Size Wt./C lb. UCN1/4 1/4 8 UCN3/8 3/8 10 UCN1/2 1/2 12 STD. PACK 100 E146 Standard Square Nut Size Wt./C lb. AB1021/4 1/4 13 AB1023/8 3/8 14 AB1021/2 1/2 14 AB1025/8 5/8 12 AB1023/4 3/4 11 AB1027/8 7/8 10 STD. PACK 100 Size Wt./C lb. ES1453/8 3/8 5.5 ES1451/2 1/2 6.0 Size Wt./C lb. E1461/4EG 1/4.93 E1465/16EG 5/ E1463/8EGC 3/ E1461/2EG 1/ E1465/8EG 5/ *Supplied with a plastic sleeve over the spring portion to prevent tangling inside the carton. A9

10 Threaded Products and Hardware E147 Flat Steel Washer STD. PACK 100 EF147 Fender Washer STD. PACK 100 E148 Lock Washer STD. PACK 100 Size Wt./C lb. E1471/4EG 1/ E1475/16EG 5/ E1473/8EG 3/ E1471/2EG 1/ E1475/8EG 5/ E1473/4EG 3/ E1477/8EG 7/ Size A B Wt./ C lb. EF1471/4EGC 1/4 11/4 5/ EF1473/8EGC 3/8 11/2 7/ EF1471/2EGC 1/2 2 9/ Size Wt./C lb. E1481/4EG 1/ E1483/8EG 3/ E1481/2EG 1/ E1485/8EG 5/ Available in Stainless Steel. Available in Stainless Steel. Available in Stainless Steel. E142 Hex Head Cap Screw STD. PACK 100 E150S Lag Bolt STD. PACK 50 E151 Coach Screw Rod Available in Stainless Steel. Size Wt./ C lb. E1421/4x100EG 1/4x E1421/4x150EG 1/4x11/ E1423/8x100EG 3/8x E1423/8x150EG 3/8x11/ E1421/2x100EG 1/2x E1421/2x150EG 1/2x11/ E1421/2x200EG 1/2x E1421/2x225EG 1/2x21/ E1421/2x250EG 1/2x21/ E1421/2x275EG 1/2x23/ H104 Hanger Rod Continuous Threaded Drill Size Size Wt./ C lb. E150S3/8x11/2EG 1/4 3/8x11/2 5 E150S3/8x2EG 1/4 3/8x2 7 E150S3/8x21/2EG 1/4 3/8x21/2 8 E150S3/8x3EG 1/4 3/8x3 9 E150S1/2x11/2EG 11/32 1/2x11/2 12 E150S1/2x2EG 11/32 1/2x2 13 E150S1/2x21/2EG 11/32 1/2x21/2 15 E150S1/2x3EG 11/32 1/2x3 18 H119 Rod Couplings Rod Size Std Rod Wt./ Lengths C lb. E1513/8x4EG 3/8 4 9 E1513/8x6EG 3/ E1513/8x8EG 3/ E1513/8x10EG 3/ E1513/8x12EG 3/ E1511/2x4EG 1/ E1511/2x6EG 1/ E1511/2x8EG 1/ E1511/2x10EG 1/ Machine threaded opposite end, carbon steel. STD. PACK 3 Thread Size Wt./lb. Design 100 ft. Load lb. H1041/4x10EGC 1/ H1043/8x10EGC 3/ H1041/2x10EGC 1/ H1045/8x10EGC 5/ H1043/4x10EGC 3/ H1047/8x10EG 7/ H1041x10EG Black available upon request Sold per foot; standard length, 10 ft. Also available in stainless steel (316) standard length 6 ft. (suffix SS6) National coarse thread Rod Size A Wt./C lb. 1/4 7/ /16 7/ /8 11/ /2 11/ /8 21/ /4 21/ /8 21/ / Standard Rod Coupling Example: H1191/2EG Order by product number, rod size, and finish. Available in Stainless Steel. Rod Size A Wt./C lb. 1/4 to 3/8 11/ /8 to 1/2 11/ /2 to 5/8 11/ /8 to 3/4 11/ /4 to 7/8 13/ Rod Reducer Coupling Example: H1191/4x3/8EG A10

11 Threaded Products and Hardware H122 Trapnut TM Strut Fastener Size Design Load (lb.) Std. Ctn. H 122 1/4 1/4 150 H 122 3/8 3/8 590 H 122 1/2 1/ H 122 1/4 EG 1/4 150 H 122 3/8 EG 3/ H 122 1/2 EG 1/ H 122 3/8 SS6 3/8 590 H 122 1/2 SS6 1/ Finishes: Electrogalvanized (EG), GoldGalv, Stainless Steel Type 316 (SS6) M117 Eye Socket A B MAX BOLT SIZE E Rod Size Pipe Wt./ Design B E A Size C lb. Load, lb. 1/4 3/8 1/4 111/ /8 1/2 2 1/4 111/ /2 21/2 31/2 1/4 117/ / /8 113/ /4 6 1/2 25/ /8 8 1/2 211/ Standard Finishes Bare (B), Electrogalvanized (EG) Malleable iron. For attaching hanger rod to various types of hangers and beam clamps. Order by product number, rod size, and finish. Example: M1171/4B Complies with Specification MSS SP69, Type 16. E120 Swivel Joint E120A Weldless Eye Nut Size A B Wt./C lb. Design Load, lb. E1203/8 3/8 13/8 3/ E1201/2 1/2 11/2 1/ E122 Swivel Joint Rod Size Wt./C Design A B C D E F T lb. Load, lb. 3/8 7/8 5/8 11/4 2 21/2 3/ /2 7/8 5/8 11/4 2 21/2 3/ /8 13/8 3/4 11/2 21/2 3 1/ /4 13/8 3/4 11/2 21/2 3 1/ /8 11/2 15/8 15/16 35/8 41/2 3/ /2 15/8 15/16 35/8 41/2 3/ Standard Finish Bare (B) Drop Forged Steel. For use on high temperature piping installations. Order by product number and rod size. Example: E120A3/8B E130 Swivel Joint E131 Swivel Joint Size A B Wt./C Design lb. Load, lb. E1223/8 3/8 13/8 3/ E1221/2 1/2 11/2 1/ Size A B Wt./C Design lb. Load, lb. E1303/8 3/8 13/8 3/ E1301/2 1/2 11/2 1/ Size A B Wt./C Design lb. Load, lb. E1313/8 3/8 13/8 3/ E1311/2 1/2 11/2 1/ A11

12 Threaded Products and Hardware C781 Square Washer STD. PACK 50 Rod Hole Overall Wt./ Size Size Dimensions C lb. C7813/8* 3/8 7/16 3 x 3 x 3/16 27 C7811/2* 1/2 9/16 3 x 3 x 3/16 27 C7815/8* 5/8 11/16 3 x 3 x 1/4 47 C7813/4* 3/4 13/16 3 x 3 x 1/4 42 C7817/8* 7/8 15/16 4 x 4 x 3/8 85 C7811* 1 11/8 4 x 4 x 3/8 160 Used for beam applications. For channel applications use AB241. *Finishes B HDG EG SS6 H115 Standard UBolt Pipe Size A B C D E Wt./ C lb. Design Load, lb. 1/2 15/16 13/4 11/2 1/4 23/ /4 11/8 13/4 15/8 1/4 31/ /8 17/8 15/8 1/4 35/ /4 123/32 13/4 115/32 3/8 31/ /2 2 13/4 17/16 3/8 33/ /16 21/16 17/8 3/8 411/ /2 215/16 21/16 113/16 1/2 51/ / /4 1/2 511/ /2 43/ /32 1/2 63/ /32 21/4 131/32 1/2 615/ /8 3 27/32 1/2 85/ /4 33/4 213/16 5/8 101/ /4 33/4 213/16 5/8 121/ / /4 149/ /8 41/4 31/4 7/8 1615/ Standard Finishes Electrogalvanized (EG), GoldGalv, Stainless Steel or Bare (B) Example: H1151/2EG Sizes through 4 in. furnished with one hex nut per leg. Sizes 5 in. and above furnished with two hex nuts per leg. Order by, pipe size, finish. Complies with Specification MSS SP69, Type 24. A12

13 Fittings and Brackets Material Superstrut fittings and brackets are man u fac tured from hot rolled carbon steel. Dimensions The following standard dimensions apply to all fittings except as indicated on the individual drawings. Hole spacing Hole spacing Hole size Material Material 13/16 in. from end of fittings 17/8 in. centers 9/16 in. diameter 15/8 in. wide 1/4 in. thick Application Instructions Parts drawings illustrate a typical use for the fitting, and in many cases other uses for the part are appropriate. Nuts and Bolts Required Unless otherwise noted, nuts and bolts for use with fittings and brackets should be ordered separately. The standard bolt for the 9/16 in. hole is a 1/2 in. hex head cap screw 1 in. long. The 1 in. length may be used with all Series channel. Design Load For more information on design load, see page A57 Engineering Data and Specifications. Finishes and Special Materials Standard finishes are Hot Dipped Galvanized (HDGC) and GoldGalv (no suffix). Fittings are also available in Electrogalvanized (EG) and Stainless Steel 316 (SS6C). Contact your Regional Sales Office for availability and minimum quantities. Aluminum channel For Aluminum channel, we suggest fittings in HDG (C) or SS6 (C). Design Data Load ratings vary depending fittings and brackets are used with 12, *14 or 16 gauge channel. Ratings are shown for each channel material. (See page A57 for Engineering Data and Specifications). A13

14 AB206 AB206HDGC AB206EG AB206 AB206SS6C Wt./C 35 lb. Fittings and Brackets Flat Fittings AB207 AB207HDGC AB207EG AB207 AB207SS6C Wt./C 52 lb. X207 X207HDG X207EG X207 X207SS6 Wt./C 78 lb. X208 X208HDG X208EG X208 X208SS6C Wt./C 88 lb. AB219 AB219HDGC AB219EG AB219 AB219SS6C Wt./C 53 lb. AB220 AB220HDGC AB220EG AB220 AB220SS6C Wt./C 78 lb. AB240 AB240HDG AB240EG AB240 Wt./C 69 lb. AB253 AB253HDGC AB253EG AB253 AB253SS6C Wt./C 97 lb. AB241 Bolt Size Wt./ C lb. AB2411/4* 1/4 18 AB2415/16* 5/16 18 AB2413/8* 3/8 18 AB2411/2* 1/2 17 AB2415/8* 5/8 15 AB2413/4* 3/4 14 AB255 AB255HDGC AB255EG AB255 Wt./C 70 lb. *Finishes HDGC GoldGalv EG SS6C AB242 AB242HDGC AB242EG AB242 Wt./C 9 lb. For use with either 3/8 in. or 1/2 in. hanger rod. AB257 AB257HDGC AB257EG AB257 Wt./C 105 lb. AB261 AB261HDGC AB261EG AB261 Wt./C 148 lb. AB263 AB263HDGC AB263EG AB263 AB263SS6 Wt./C 150 lb. AB265 AB265HDGC AB265EG AB265 Wt./C 105 lb. Standard Dimensions Hole Spacing 13/16 in. From End Hole Spacing 17/8 in. Centers Hole Size 9/16 in. Diam. Material 15/8 in. Width Material 1/4 in. Thick Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A14

15 Fittings and Brackets 90º Fittings AB201 AB201HDGC AB201EG AB201 AB201SS6C Wt./C 35 lb. AB202 AB202HDGC AB202EG AB202 AB202SS6C Wt./C 35 lb. AB203 AB203HDGC AB203EG AB203 AB203SS6C Wt./C 58 lb. AB204 AB204HDGC AB204EG AB204 AB204SS6 Wt./C 58 lb. AB205 AB205HDGC AB205EG AB205 AB205SS6C Wt./C 78 lb. AB213 AB213HDGC AB213EG AB213 Wt./C 125 lb. AB214 AB214HDGC AB214EG AB214 AB214SS6 Wt./C 125 lb. AB254R AB254RHDGC AB254REG AB254R Wt./C 105 lb. AB216 AB216HDGC AB216EG AB216SS6C Wt./C 135 lb. AB254L AB254LHDGC AB254LEG AB254L Wt./C 105 lb. AB252 A Wt./C lb. AB2521* 37/8 61 AB2522* 57/8 84 AB2523* 77/8 107 AB2524* 97/8 130 *Finishes HDGC EG GoldGalv AB260R AB260RHDGC AB260REG AB260R Wt./C 58 lb. AB260L AB260LHDGC AB260LEG AB260L Wt./C 58 lb. AB274 AB274HDG AB274EG AB274 Wt./C 70 lb. AB275 AB275HDGC AB275EG AB275SS6C Wt./C 77 lb. Standard Dimensions Hole Spacing 13/16 in. From End Hole Spacing 17/8 in. Centers Hole Size 9/16 in. Diam. Material 15/8 in. Width Material 1/4 in. Thick Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A15

16 AB284R AB284RHDG AB284REG AB284R Wt./C 230 lb. Fittings and Brackets 90º Fittings AB284L AB284LHDG AB284LEG AB284L Wt./C 230 lb. AB299 AB299HDG AB299EG AB299 Wt./C 40 lb. X201 X201HDG X201EG X201 Wt./C 65 lb. X204 X204HDG X204EG X204 Wt./C 190 lb. X289 X289HDGC X289EG X289 Wt./C 105 lb. X299 X299HDGC X299EG X299 Wt./C 38 lb. N205 N205HDGC N205EG N205 N205SS6C Wt./C 74 lb. N219 N219HDG N219EG N219 N219SS6 Wt./C 71 lb. Standard Dimensions Hole Spacing 13/16 in. From End Hole Spacing 17/8 in. Centers Hole Size 9/16 in. Diam. Material 15/8 in. Width Material 1/4 in. Thick Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A16

17 Fittings and Brackets Angular Fittings AB225 AB225HDGC AB225EG AB225 AB225SS6 Wt./C 58 lb. AB226 AB226HDGC AB226SS6 Wt./C 119 lb. AB227 AB227HDGC AB227EG AB227 AB227SS6 Wt./C 58 lb. AB228 AB228HDGC AB228SS6C Wt./C 69 lb. Other angles available. Contact your Regional Sales Office. AB231 AB231EG Other angles available. Contact your Regional Sales Office. AB232 AB232EG Other angles available. Contact your Regional Sales Office. AB239 Other angles available. Contact your Regional Sales Office. *Finishes HDGC EG GoldGalv A B Wt./C lb. AB2391* 713/16 81/2 148 AB2392* 133/ AB2393* 193/4 251/2 363 Z Shape Fittings A209 A209HDGC A209EG A209 A209SS6 Wt./C 55 lb. B209 B209HDG B209EG B209 Wt./C 43 lb. C209 C209 Wt./C 49 lb. For attaching A and AR Series channel. D209 Wt./C 45 lb. For attaching B and BR Series channel. CZ209 For attaching C Series channel. EZ209 EZ209HDGC EZ209EG EZ209 EZ209SS6 For attaching D Series es channel. For attaching H Series and A back to back. For attaching E Series channel. Standard Dimensions Hole Spacing 13/16 in. From End Hole Spacing 17/8 in. Centers Hole Size 9/16 in. Diam. Material 15/8 in. Width Material 1/4 in. Thick Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A17

18 A208 A208HDGC A208EG A208 A208SS6C Wt./C 275 lb. Fittings and Brackets U Shape Fittings A213 Inside Joiner Wt./C 40 lb. A210 A210HDGC A210EG A210 A210SS6C Wt./C 88 lb. Does not include stud nut or bolts. For A and AR Series channel. A211 A211HDGC A211EG A211 Wt./C 128 lb. For A1200 Series. Available only in GoldGalv finish. AN211 AN211HDG AN211EG AN211 Wt./C 181 lb. For attaching A and AR Series channel. A212 A212HDG A212EG A212 A212SS6 Wt./C 113 lb. For attaching A and AR Series double channel, and H Series. B210 B210HDG B210EG B210 B210SS6 Wt./C 65 lb. C210 C210HDG C210EG C210 Wt./C 77 lb. D210 D210HDG D210EG D210 D210SS6 Wt./C 71 lb. For attaching B and BR Series. E210 E210HDGC E210EG E210 Wt./C 112 lb. For attaching E Series channel. For attaching C Series channel. AB245 AB245HDG AB245EG AB245 Wt./C 70 lb. For attaching A and AR Series double channel. For attaching D Series channel. AB288 *Finishes HDGC EG GoldGalv Bolt Size Wt./C lb. AB2883/8* 3/8 AB2881/2* 1/2 37 AB2885/8* 5/8 Standard Dimensions Hole Spacing 13/16 in. From End Hole Spacing 17/8 in. Centers Hole Size 9/16 in. Diam. Material 15/8 in. Width Material 1/4 in. Thick Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A18

19 Fittings and Brackets Wing Fittings AW204 AW204HDG AW204EG AW204 Wt./C 76 lb. AW214 AW214HDG AW214EG AW214 Wt./C 115 lb. A217 AW217HDG A217EG A217 Wt./C 155 lb. AW205L AW205LHDG AW205LEG AW205L Wt./C 59 lb. AW205R AW205REG AW205R Wt./C 59 lb. AW215L AW215LHDG AW215LEG AW215L Wt./C 98 lb. AW215R AW215RHDG AW215REG AW215R Wt./C 98 lb. 3 7 /8 3 7 /8 AW220 AW220HDGC AW220EG AW220 Wt./C 90 lb. AW224 AW224HDGC AW224EG AW224 Wt./C 147 lb. AW219 AW219HDGC AW219EG AW219 Wt./C 187 lb. AW226 AW226HDG AW226 Wt./C 113 lb. A218 A218HDG A218EG A218 Wt./C 177 lb. AW228 AW228HDG AW228EG AW228 Wt./C 230 lb. Standard Dimensions Hole Spacing 13/16 in. From End Hole Spacing 17/8 in. Centers Hole Size 9/16 in. Diam. Material 15/8 in. Width Material 1/4 in. Thick Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A19

20 S202 Fittings and Brackets Brackets S203 S249 *Finishes HDG A B C Wt./C lb. S2026* S2029* S20215* S20221* S20227* S20233* S250 *Finishes HDG A B Design Wt./ Load/lb. C lb. S2038* 81/2 41/ S20314* 141/2 53/8 325 S20320* 201/2 611/ S20326* 261/ S20332* 321/ S20338* 381/ S251 *Finishes HDG SS6C A B Design Wt./ Load/lb. C lb. S2498* 81/ S24914* 141/ S24920* 201/ S24926* 261/2 111/2 870 S24932* 321/2 111/ S24938* 381/2 111/ S256 *Finishes HDG SS6C A Design Wt./C Load/lb. lb. S2506* S2508* 81/ S25012* S25014* 141/ S25018* S25020* 201/ S25024* S25026* 261/ May be installed inverted with no change in load ratings. S247 S247HDG S247 S247SS6 *Finishes HDG SS6C A Design Wt./ Load/lb. C lb. S25112* S25114* 141/ S25118* S25120* 201/ S25124* S25126* 261/ S25130* S25132* 321/ S25136* S25138* 381/ Design Moment (channel upright as shown) When Supported By A inch lb. A inch lb. Applies to fitting only, not to the arm. S248 S248HDGC S248 *Finishes HDG SS6C A Design Wt./ Load/lb. C lb. S2566* S2568* 81/ S25612* S25614* 141/ S25618* S25620* 201/ S25624* S25626* 261/ When installed in inverted position reduce load rating 40%. Design Moment (channel upright as shown) When Supported By A inch lb. A inch lb. Applies to fitting only, not to the arm. Standard Dimensions Hole Spacing g 13/16 in. From End Hole Spacing g 17/8 in. Centers Hole Size g 9/16 in. Diam. Material g 15/8 in. Width Material g 1/4 in. Thick Materials HDG(C) g HotDipped Galvanized EG(C) g Electrogalvanized (No suffix) g GoldGalv SS6(C) g Stainless Steel 316 A20

21 Fittings and Brackets Brackets S204 S204HDGC S204 Wt./C 174 lb. Design Uniform Load/lb. A A S205 S205HDGC S205 Wt./C 264 lb. Design Uniform Load/lb. A A S217 S217HDG S217 S217SS6 Wt./C 264 lb. Design Uniform Load/lb. A A S218 S218HDG S218 Wt./C 295 lb. Design Uniform Load/lb. A A S222 S222HDG S222 Wt./C 385 lb. Design Uniform Load/lb. A A S226 S226HDG S226 Wt./C 421 lb. Design Uniform Load/lb. A A A21

22 Fittings and Brackets Post Bases AP232 AP232HDGC AP232EG AP232 Wt./C 384 lb. AP235 AP235HDGC AP235EG AP235 Wt./C 400 lb. AP232SQ AP232SQHDGC AP232SQEG AP232SQSS6 Wt./C 384 lb. AP235SQ AP235SQHDGC AP235SQEG AP235SQ AP235SQSS6 Wt./C 400 lb. AN270 TS272 Track Support TS272HDG TS273 Track Support TS273HDG *Finishes HDG EG A B Wt./C lb. AN2701* 23/ AN2702* 43/ AN2703* 63/ AN2704* 83/ AN270* 103/ Requires 3/8 in. x 21/2 in. bolt and nut (not included) Design load: 1000 lb. Wt./C 104 lb. For use over channel splice Requires 3/8 in. x 21/2 in. bolt and nut (not included) Design load: 2000 lb. Wt./C 228 lb. A22

23 Fittings and Brackets Special Application Fittings and Brackets TR292 TR294 C728 Pipe Roller (Pair) Can be used for Series A, E and H channels only. Standard finish is Electrogalvanized. Frictionless needle bearings. Design load: 500 lb. Safety factor of 5. Wt./C 59 lb. Can be used for Series A, E and H channels only. Standard finish is Electrogalvanized. Frictionless needle bearings. Design load: 1000 lb. Safety factor of 5. Wt./C 106 lb. Adjustable Universal Support Support building services and access equipment on flat roofs and flat surfaces Cast aluminum rollers, steel brackets. Designed for standard saddles. Order separately for each pair of rollers: two 1/2 in. x 5/16 in. hex head cap screws and two 1/2 in. channel nuts. Space to suit O.D. of pipe and wrapping. Design Load: 2350 lb. Wt./C : 300 lb. The T&B Adjustable Universal Support (AUS) provides an easy method for supporting pipes, conduit and equipment on flat roofs, below raised floors and even on level ground applications. The AUS reduces installation time compared to other support solutions such as wooden blocks, cement blocks, straps and clips. These labor intensive solutions also increase the danger of roof membrane penetration. The AUS system also allows for tool free adjustment of the pedestal height from 6 to 9 inches with a twist of the wrist. This ensures that the supported objects or pipes are uniformly supported and no high stress supports are carrying a disproportionate load in a single location. Description Qty. AUS1496 Ajustable Universal Support (Base only) 1 AUSRISERKIT A1200HS100PG H1041/2X10EGC E1451/2EGC E1471/2EGC E1481/2EGC AUSSTRUTKIT A1200HS100PG E1421/2X200EGC E1451/2EGC E1471/2EGC E1481/2EGC AUS125PCSS6 AUS150PCSS6 AUS200PCSS6 Riser Kit 14 in. strut 12 in. threaded rod Nut Washer Lock washer Bolt Kit 14 in. strut Bolt Nut Washer Lock washer 41/2 in. stainless steel 316 strap (to restrain 11/4 in. pipe) 5 in. strap (to restrain 11/2 in. pipe) 6 in. strap (to restrain 2 in. pipe) Riser Kit Bolt Kit Straps Pipe Grooves 12 in. Platform Adjustable Height Jackscrew Locking Mechanism Sturdy Jackscrew Base to Distribute Load Flexible PVC Mat to Eliminate Stress Points A23

24 Beam Clamps Design Loads Where design loads are indicated, they provide for a safety factor of 3 in conformance with the American Standard Code for Pressure Piping. For more information, see page A57 for Engineering Data and Specifications. Finishes and Special Materials HotDipped Galvanized (HDGC) is standard for all Superstrut beam clamps. The material is zinc coated after fabrication providing total product protection on all surfaces. The fabricated beam clamps are suspended and then dipped into tanks of hot zinc for a prolonged period, creating a coherent bond. Selected beam clamps can also be available in GoldGalv (no suffix) or Stainless Steel Type 316 (SS6C). Contact your Regional Sales Office for availability and minimum quantities. A24

25 Beam Clamps Beam Clamps for Mounting Channel U501, U502 *Finishes HDG EG GoldGalv SS6C For Channel Size Wt./C lb. U501* A1200 A /16 90 B1200 B1400 C1200 B1402 U502* A1202 A / C1202 H1200 Furnished complete. Design Load U501 : 2150 lb. U502 : 3000 lb. U510 U510HDGC U510EG U510 U510SS6 U504 U504HDG U504EG U504 U504SS6 Can be used with all channels. Wt./C 140 lb. 512U 512UHDG 512UEG 512U U505 U505HDG U505EG U505 Can be used with all channels. Wt./C 270 lb. U514 U514HDGC U514EG U514 U514SS6 Design Load/lb. Channel 1000 A A1400 1/2 in. x 11/2 in. set screw included. Order separately one 1/2 in. x 11/2 in. hex head cap screw and 1/2 in. channel nut. Wt./C 75 lb. U514A U514AHDGC U514AEG U514A U514ASS6 Design Load/lb. Channel 1000 A A1400 Order separately one 1/2 in. x 11/2 in. hex head cap screw and 1/2 in. channel nut. Wt./C 26 lb. U5155 U515HDGC U515EG U515 U515SS6 3/8 in. x 11/2 in. set screw included. Design Load 750 lb./pair Wt./C 40 lb. U515B U515BHDG U515BEG U515B U515BSS6 1/2 in. x 11/2 in. set screw included. Design Load 1650 lb./pair Wt./C 59 lb. For all A Series channel. 1/2 in. x 11/2 in. set screw included. Design Load 800 lb. Wt./C 95 lb. For all B Series channel. 1/2 in. x 11/2 in. set screw included. Design Load 800 lb. Wt./C 91 lb. Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A25

26 Beam Clamps Beam Clamps for Mounting Channel U520, U521, U522 U544 Single Adjusting Screw End Cap Set U544EG U543 Adjusting Screw End Caps U543HDG U543EG U543 *Finishes GoldGalv Flange Wt./ Design A Width C lb. Load lb./ea U520* 23/8 41/2 83/ U521* 33/4 53/ U522* 55/8 75/8 117/ Nuts, cap screws and set screws included. A597 Should be ordered as one set. Wt./C 39 lb. U5701, U5702 Should be ordered in multiples of two (2). Wt./C 44 lb. F *Finishes HDGC SS6C Channel Design Wt./C lb. Series Load lb./ea A597* A *Finishes HDGC A Ø 9/16 in. A F Wt./ Design C lb. Load lb./ea U5701* 11/2 4 to U5702* 11/2 7 to Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A26

27 Beam Clamps Beam Clamps for Hanging Rod U562 Beam Clamp U562HDG U562EG U562 U562SS6 Optional Use of U562HDG Beam Clamp UM562 Beam Clamp UM562HDGC UM562EG UM562 UM562SS66 US562 Beam Clamp with Swing Hanger US562HDG US562EG US562 E146 square nut order separately. 1/2 in. set screw included. Rod Size Wt./C lb. Design Load lb./ea 1/ For 20 swivel application use ES1451/2 nut. U563 Beam Clamp U563HDG U563EG U563 U563SS6 Optional Use of U563HDG Beam Clamp 1/2 in. set screw included. Rod Size Wt./C lb. Design Load lb./ea 1/ E146 square nut order separately. 1/2 in. set screw included. Rod Size Wt./C lb. Design Load lb./ea 1/ For 20 swivel application use ES1451/2 nut. 1/2 in. set screw included. Rod Size Wt./C lb. Design Load lb./ea 1/ US563 Beam Clamp with Swing Hanger US563HDG US563 Square nut order separately. 3/8 in. set screw included. Rod Size Wt./C lb. Design Load lb./ea 3/ U569 Beam Clamp U569HDG U569 3/8 in. set screw included. Rod Size Wt./C lb. Design Load lb./ea 3/ /8 in. set screw included. Rod Size Wt./C lb. Design Load lb./ea 3/ A570 Beam Clamp with Safety Rod 3/8 in. Maximum flange width idth5i in. A Size Wt./C lb. Design Load lb./ea U569 3/ /8 in. Flange width 4 in. min. 8 in. max. For use with 3/8 in. rod see U569. A Size Wt./C lb. Design Load lb./ea A570HDG 1/ /8 in. Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A27

28 Beam Clamps Beam Clamps for Hanging Rod U560 Heavy Duty Beam Clamp U564 Heavy Duty Beam Clamp *Finishes GoldGalv EG A B C Wt./C Design lb. Load, lb. U5601/4* 1/4 1/8 3/8 x 11/ U5603/8* 3/8 1/8 3/8 x 11/ U5601/2* 1/2 1/4 1/2 x 11/ U5605/8* 5/8 1/4 1/2 x 11/ U568 Beam Clamp Safety Strap U568 Beam Clamp Safety Strap *Finishes GoldGalv EG A B C Wt./C Design lb. Load, lb. U5643/8* 3/8 1/8 3/8 x 23/ U5641/2* 1/2 1/4 1/2 x 23/ U5645/8* 5/8 1/4 1/2 x 23/ U568 Beam Clamp Safety Strap For U563 beam clamp. Beam Flange Wt./C Width A lb. U5681EG U5682EG gauge material C775L / M775L Clamp with Lock Nut For U562 and UM562 beam clamp. Beam Flange Wt./C Width A lb. U5683EG U5684EG U5685EG gauge material For U560 and U564 beam clamp. Standard Finish Electrogalvanized (EG) Malleable Iron (M775L) Carbon Steel (C775L) Beam Flange Wt./C Width A lb. U5684EG U5685EG U5686EG gauge material C775L A B M775L C Pipe Dimensions Wt./C Design Size A B C lb. Load, lb. C775L3/8EG 3/8 3/8 3/8 3/ C775L1/2EG 1/2 3/8 3/8 3/ C775L5/8EG 5/8 1/2 1/2 3/ C775L3/4EG 3/4 5/8 5/8 3/ C775L7/8EG 7/8 3/4 3/ M775L3/8EG 3/8 3/8 3/4 13/ M775L1/2EG 1/2 1/2 3/4 13/ M775L5/8EG 5/8 5/8 3/ M775L3/4EG 3/4 3/4 3/ Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 A28

29 Beam Clamps Beam Clamps for Hanging Rod 500SC, 502, 503SC, 507, 508, 509, 510, 511 Beam Clamp Standard Finish Electrogalvanized (no suffix) Tapped Holes Base Dim. A B Jaw Opening Wt./C lb. De sign Load/lb. 500SC 1/ /4 15/ / SC 1/ /8 21/ / /2 23/8 13/ / /2 23/8 21/ /4 15/ / /32 11/8 5/ /32 11/8 5/ H Series in combination with 500 Series Beam Clamp Conduit and Pipe Hanger Features Accommodates 1/2 in. through 4 in. EMT or rigid conduit Can be used for either vertical or horizontal installation 6HTB Series is threaded so there are less parts to handle or drop Installs easily with a screwdriver 6H Series without bolt Fig. 1 6HT Threaded Series threaded without bolt Fig. 3 6HB Series with bolt and hex nut Fig. 2 6HTB Threaded Series threaded with bolt Fig.4 Without Bolt With Bolt EMT Rigid Conduit Qty. per Fig. No. Fig. No. or Pipe Box 6H0 1 6H0B 2 6H0T 3 6H0TB 4 1/2 3/81/2 6H1 1 6H1B 2 6H1T 3 6H1TB 4 3/4 3/4 6H2 1 6H2B 2 6H2TB H2 1/2 1 6H2 1/2B 2 6H2 1/2TB 4 11/4 6H3SC 1 6H3B 2 6H3TB 4 11/2 11/ H4 1 6H4B 2 6H4TB 4 11/2 6H5 1 6H5B 2 6H5TB H6 1 6H6B 2 21/2 21/2 6H7 1 6H7B H8 1 6H8B 2 31/2 31/2 6H9 1 6H9B Standard Finish Electrogalvanized (no suffix). Use SS suffix for Stainless Steel. Load rating: 500 lb. with a safety factor of 3. (For weight per 100 see page A38.) A29

30 Beam Clamps Beam Clamps for Mounting Pipe and Conduit U571, U572 Conduit Clamp For attaching 1/2 in. thru 11/2 in. conduit to beam, channel, angle or column. Secures conduit to the support parallel or at right angles to it. 5/16 in. set screw 12 gauge material Standard Finish GoldGalv Wt./C 38 lb. Conduit Size Max. Flange Thickness U571 1/2 1 3/4 3/4 1 1/2 U572 3/4 11/2 1 11/4 11/4 1 11/2 5/8 Dim. A Wt./C lb. 13/ /2 59 Pipe Supports Type RC and RCS Type EC Type PC Malleable Iron For mounting pipe or conduit at right angles to the beam Use SS316 suffix for 316 Stainless Steel Use HDG suffix for HotDipped Galvanized Malleable Iron For mounting pipe or conduit vertically across the beam Use HDG suffix for HotDipped Galvanized CSA Certified Malleable Iron For mounting pipe or conduit parallel to the beam Use HDG suffix for HotDipped Galvanized Pipe Supports Three types of pipe clamps are available to provide right angle, vertical and parallel attachment to a beam. Types RC, EC and PC are malleable iron clamps with an edge that grips the structural member for maximum holding power when tightened. Type RCS clamps are all steel, providing two bearing surfaces for strong attachment for mounting pipe or conduit at right angles to the beam. All parts are electrogalvanized (no suffix) including the threads. The clamps are designed for clamping to a wide variety of beam thicknesses and tapers. Can be installed using only a wrench. and Size O.D. of Conduit or Pipe Nom. Conduit or Pipe Size Std. Ctn. Wt./C lb. RCS3/ /8 31 RCS1/ /2 34 RCS3/ /4 39 RCS RCS11/ /4 43 RCS11/ /2 60 RCS RC1/ /2 36 RC3/ /4 43 RC RC11/ /4 51 RC11/ /2 54 RC2SC RC21/ /2 107 RC RC31/ /2 134 RC4SC EC1/ / EC3/ /4 78 EC EC11/ / EC11/ /2 112 EC EC21/ / EC PC3/ /8 32 PC1/ / PC3/ /4 53 PC PC11/ /4 79 PC11/ / PC PC21/ /2 148 PC PC31/ / PC A30

31 Beam Clamps Beam Fittings C781 Square Washer M742R Ceiling Flange *Finishes B EDG EG SS6 Used for beam applications. For channel applications use AB241. STD. PACK 50 Rod Size Hole Size Overall Dimensions Wt./C lb. C7813/8* 3/8 7/16 3 x 3 x 3/16 27 C7811/2* 1/2 9/16 3 x 3 x 3/16 27 C7815/8* 5/8 11/16 3 x 3 x 1/4 47 C7813/4* 3/4 13/16 3 x 3 x 1/4 42 C7817/8* 7/8 15/16 4 x 4 x 3/8 85 C7811* 1 11/8 4 x 4 x 3/8 160 *Finishes B EG Rod Size Wt./C lb. M742R3/8* 3/8 16 M742R1/2* 1/ Side Beam Hanger Clip 542 Side Beam Hanger Clip S541 Swing Connector *Finishes B EG GoldGalv A B C D Wt./C lb. 5403/8* 7/16 17/8 1/4 7/ /2* 9/16 17/8 1/4 15/ /8* 11/16 21/2 3/ /4* 13/16 21/2 3/ /16 Dia. 1/4 Dia. 7/16 Dia. 3/ /16 21/16 7/16 Dia. 1/4 Dia. 9/16 Dia. 3/16 Figure 1 Figure /16 Design Figure Rod Size Wt./C lb. Load/lb. 1 3/ / Standard Finish GoldGalv For 3/8 in. and 1/2 in. rods. 21/16 3/8 in. x 13/4 in. bolt, nut and clevis included. Rod Size Wt./C lb. S5413/8 3/8 31 Standard Finish GoldGalv For use with wood beam. Materials HDG(C) g HotDipped Galvanized EG(C) g Electrogalvanized (No suffix) g GoldGalv SS6(C) g Stainless Steel 316 B g Bare A31

32 Beam Clamps Beam Fittings U577 Clevis and Swing Connector U576 Hanger Clevis U579 Ceiling Flange Rod Size Wt./C lb. U5771/2 1/2 69 Standard Finish GoldGalv For use with wood beam. Hole A U5763/8 7/16 U5761/2 9/16 Material Thikness B Standard Finish GoldGalv Wt./C lb. 3/16 27 For rods up to 1/2 in. Mounting holes 7/16 in. di am e ter. For use with wood beam. A Wt./C lb. U5793/8 31/2 30 U5791/2 41/4 50 Standard Finish GoldGalv Malleable Iron Nuts and wood screws not included. Mounting holes 13/32 in. Materials HDG(C) HotDipped Galvanized EG(C) Electrogalvanized (No suffix) GoldGalv SS6(C) Stainless Steel 316 B Bare A32

33 Pipe Straps, Pipe Clamps and Hangers Design Loads Where design loads are indicated, they provide for a safety factor of 3 in conformance with the American Standard Code for Pressure Piping. Hanger Design Pipe hangers are of advanced design to be user friendly. Finishes and Special Materials The standard finish is Electrogalvanized (EGC) or GoldGalv. Some products are offered in Aluminum and Stainless Steel where noted. 701 O.D. Pipe and Conduit Clamp Machine screw and nut included. Standard Finishes and Materials PG = Pregalvanized (i.e PG) AL = Aluminum (i.e AL) with zinc plated hardware SS6 = Stainless Steel Type 316 (i.e SS6) N de cat. O.D. of pipe Rigid EMT WT./C. (mm) Cond. Cond. lb PG PG PG PG / PG / PG / PG / PG PG PG / PG / PG / PG / PG PG PG PG PG PG /2 21/ PG PG PG PG PG PG PG /2 31/ PG PG PG PG Std. Pack 10 5 A33

34 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps 703 Universal Clamp EMT/ Rigid Conduit O.D.0 Material Thickness Wt./C lb. Std. Ctn. 7031/2EG 1/ ga /4EG 3/ ga EG ga /4EG 11/ ga /2EG 11/ ga EG ga Standard Finishes GoldGalv (i.e.) 7031/2 Electrogalvanized (EG suffix) (i.e.) 70311/2EG One size fits both Rigid and Electric Metal Tubing (EMT). Individually assembled with screw and nut. Quik Clamp II TM Design Load 2 Design Load 3 A Design Load 1 Design Load 1 has a safety factor of 4. Design Loads 2 and 3 have a safety factor of 1. Dimension A EMT in. (mm) Dimension A Rigid Conduit in. (mm) Quantity per Box Wt./C lb. TBQC050 15/16 (33.5) 11/4 (31.5) TBQC075 13/4 (44.5) 111/16 (43) TBQC /16 (46) 13/4 (44.5) TBQC125 21/8 (54) 2 (51) TBQC150 23/8 (60.5) 23/16 (55.5) TBQC200 25/8 (66.5) 21/2 (63.5) TBQC250 31/16 (78) 31/16 (78) TBQC /16 (93.5) 311/16 (93.5) TBQC350 43/16 (106.5) 43/16 (106.5) TBQC /16 (119) 411/16 (119) Design Load 1 Static Load Limit lb. (kg) 200 (90) 200 (90) 200 (90) 200 (90) 200 (90) 200 (90) 350 (158) 350 (158) 350 (158) 350 (158) Design Load 2 lb. (kg) Design Load 3 lb. (kg) 50 (23) 50 (23) Standard material electrogalvanized steel. A34

35 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps Cobra Clamp Design Load 2 Design Load 3 Standard material is commercialgrade, bright electrogalvanized steel. Stainless steel 316L is also available; add the suffix SS6 to catalogue no. (i.e.: CPC050SS6). Stainless steel bolt head is hexagonal and slotted only. Now available in aluminum. Design Load 1 EMT Trade Size Rigid Cond. Trade Size Cable O.D. Range Static Load Limit (lb.) Safety Factor = 4 Qty. per Box Wt./C lb. CPC025 1/4 1/ CPC050 1/2 1/ CPC075 3/4 3/ CPC CPC /4 1 1/ CPC /2 1 1/ CPC CPC /2 2 1/ CPC CPC /2 3 1/ CPC Torque Value (ft.lb.) 35 Design Load 1 Static Load Limit lb. (kg) 200 (91) 200 (91) 200 (91) 200 (91) 200 (91) 200 (91) 350 (159) 350 (159) 350 (159) 350 (159) Design Load 2 lb. (kg) Design Load 3 lb. (kg) 50 (23) 50 (23) LocKing Cobra TM Clamp Superior design load capabilities for heavyduty applications Preset torque prevents overtightening Antivibration nut Steel construction with GoldGalv finish Design Load 2 Design Load 1 Design Load 3 EMT Rigid Cond. Trade Trade Size Size Cable O.D. Range Static Load Qty. Limit (lb.) per Safety Box Factor = 4 Wt./C lb. LKCPC050 1/2 1/ LKCPC075 3/4 3/ LKCPC LKCPC /4 1 1/ LKCPC /2 1 1/ LKCPC LKCPC /2 2 1/ LKCPC LKCPC /2 3 1/ LKCPC Torque Value (ft.lb.) 35 Design Load 1 Static Load Limit lb. (kg) 350 (159) 350 (159) 350 (159) 350 (159) 350 (159) 350 (159) 350 (159) 450 (204) 450 (204) 450 (204) Design Load 2 lb. (kg) Design Load 3 lb. (kg) 50 (23) 50 (23) A35

36 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps CH118 Heavy Duty Cable Clamp O.D. of cable or pipe (mm) Rigid Cond. EMT Cond. WT./C. lb. Standard Finishes: Electrogalvanized (EG) Aluminum (AL) comes complete with Stainless Steel Type 304 saddle and hardware Stainless Steel Type 316 clamp comes with Type 304 stainless steel hardware. CH118055EG CH118081EG /2 1/2 9 CH118110EG /4 3/4 17 CH118125EG / CH118135EG CH118175EG /4 11/4 21 CH118205EG /2 11/2 24 CH118250EG CH118300EG /2 21/2 54 CH118325EG CH118375EG CH118425EG /2 31/2 113 CH118475EG Available in double or triple configurations. Example: Double CH128047EG Triple CH138047EG CB118 Counterbed EB118 Extended Bed DB118 Double Bed EB118 Extended Bed CB118 Counterbed Not Sold in pairs Wt./C. lb. Counterbed CB118055PG 1 CB118090PG 2 CB118110PG 31/2 CB118140PG 4 CB118175PG 41/2 CB118200PG 5 CB118250PG 11 CB118300PG 13 Extended bed EB118047PG 4 EB118055PG 41/2 EB118090PG 6 EB118110PG 131/2 EB118140PG 16 EB118175PG 17 EB118200PG 20 EB118250PG 30 EB118300PG 38 Double Bed DB118047PG 2 DB118055PG 2 DB118070PG 3 Standard Finishes Pregalvanized (PG) DB118 Double Bed A36

37 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps A716 Snap Guard Cushioned Clamp Tube Series P716 Snap Guard Cushioned Clamp Pipe Series Standard Finishes GoldGalv Available in Stainless Steel 316 use SS316 suffix. (i.e) A7161SS316 Electrogalvanized (Silver) use EG suffix. (i.e) A7161EG A716 / P716 Assembly consisting of GoldGalv finish steel clamp with bolt/locknut and cushion Secure pipes, tubes and hoses for fluid conductors. Installation is easy and requires no more time than a simple pipe clamp installation Cushion absorbs the shocks and associated vibrations from fluid surges in tubes, pipes and hoses It can handle temperatures from 149 C to 40 C (300 F to 40 F) Cushioned Clamp assemblies are available individually bagged Assembly Tube O.D. Tubing Wt./C lb. Assembly Standard Pipe Nominal Pipe Size Std. Ctn. Wt./C lb. A7161/4 1/4 10 P7161/4 1/4 10 A7163/8 3/8 14 P7163/8 3/8 14 A7161/2 1/2 16 P7161/2 1/ A7165/8 5/8 16 P7163/4 3/4 18 A7163/4 3/4 18 P A7167/8 7/8 18 P71611/4 11/4 27 A P71611/2 11/2 36 A71611/8 11/8 24 P A71611/4 11/4 27 P71621/2 21/2 49 A71613/8 13/8 27 P A71611/2 11/2 36 P71631/2 31/2 62 A71615/8 15/8 37 P A71613/4 13/4 37 A71617/8 17/ A A71621/8 21/8 44 A71623/8 23/8 49 A71625/8 25/8 53 A71631/8 31/8 62 A71641/8 41/8 94 U716 Two Hole Cushioned Clamp U716 Guides, protects, and uniformly spaces line runs. Low cost, time saving method of attaching tubing and hose to equipment. Cushion is built to withstand the effects of most oils, chemical and industrial cleaning compounds, in temperatures from 45 C to 121 C ( 50 F to 275 F). Interlock edge insures cushion remains in place. Attached with two standard fasteners to any flat surface, this clamp eliminates the use of special channels, providing a savings in both space requirements and cost Cushioned clamps reduce vibration, shock, and noise in fluid systems and eliminates electrolysis Standard Finish GoldGalv Assembly Copper and Steel Tubing O.D. Copper Water Pipe (nom.) Normal Pipe Size Std. Ctn. Wt./C lb. U7161/4 1/4 3 U7163/8 3/8 1/4 4 U7161/2 1/2 3/8 1/4 6 U7165/8 5/8 1/2 3/ U7163/4 3/4 5/8 7 U7167/8 7/8 3/4 1/2 7 U U71611/8 11/8 1 8 U71611/4 11/4 17 U71613/8 13/8 11/4 20 U71611/2 11/2 22 U71615/8 15/8 11/ U U71621/8 21/8 41 U71623/8 23/8 44 A37

38 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps 6H Series Conduit and Pipe Hanger 6H Series 6HTB Threaded Series 6HB Series with Bolt and Hex Nut 6HT Threaded Series Features Accommodates 1/2 in. through 4 in. EMT or rigid conduit Can be used for either vertical or horizontal installation 6HTB Series have a builtin nut so there are fewer parts to handle or drop Installs easily with a screwdriver Standard Finish Electrogal va nized (no suffix) Conduit Size Wt./C. Rigid EMT lb. 6H0 5 6H0B 7 3/8 1/2 1/2 6H0T 5 6H0TB 6 6H1 6 6H1B 7 3/4 3/4 6H1T 6 6H1TB 7 6H H2B 9 6H21/2 8 11/4 6H21/2B 10 6H3SC 8 6H3B 11/4 11/2 10 6H3TB 10 6H4 17 6H4B 11/2 19 6H4TB 19 6H5 24 6H5B H5TB 26 6H /2 21/2 6H6B 30 6H H7B H /2 31/2 6H8B 41 6H H9B 47 Cable Tie Mounting Bases For Framing Channel Installation Channel Size Maximum Tie Width Accom. Unit Qty. Std. Pkg. TC5363X 11/2 & 15/ Installs with a push and twist Designed for indoor or outdoor use Smooth design protects cable insulation Takes range of cable diameters When fastening wire bundles, cables, or hoses to framing channels, you can cut costs considerably by using this mounting base. It is made of smooth, weatherresistant nylon and designed to protect cable insulation and hoses from the wear or damage that can occur with metal clamps. The mounting base may be used for both indoor or outdoor applications. It installs in the framing channel with a simple push and twist. It requires no screws, nuts or tools. The mounting base fits all 11/2 in. and 15/8 in. channels regardless of channel depth. TyRap and TyFast to be ordered separately. A38

39 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps W716 Maple Hardwood Clamps Standard Finishes Pregalvanized (PG) Aluminum (AL) 1/8 1/ /8 15/ Paraffin impregnated maple. 13/8 1/ Dimensions Hardwood Depth Width Paraffin Imp. (mm) (mm) W7163/4PG 3/ / W7161PG / W71611/4PG 11/ / W71611/2PG 11/ / W71613/4PG 13/ W7162PG / W71621/4PG 21/ / W71621/2PG 21/ / W71623/4PG 23/ / W7163PG / W7164PG / Note: Holding clamp is included with W716 maple hardwood clamps. It is not necessary to order 701 Series separately. U861, U862 and 863 Maple Cable Clamp Electrogalvanized hardware included. Custom made to your needs Step 1 Number of holes i.e. U861 1 hole U862 2 holes U863 3 holes Step 2 Specify O.D. of cable i.e. 3/4 in. hole U Communiquer avec le bureau régional des ventes. WS716 Maple Hardwood Saddle Paraffin impregnated maple. To fasten saddle, use 3/8 in. x 2 in. screw bolt. STD. PACK 10 Dimensions Hardwood Depth Width Height Paraffin Imp. (mm) (mm) (mm) WS7163/4 3/ / WS / WS71611/4 11/ / WS71611/2 11/ / WS71613/4 13/ / WS / WS71621/4 21/ / / WS71621/2 21/ / / WS71623/4 23/ / WS / WS71631/4 31/ / / WS71631/2 31/ / WS71633/4 33/ / WS / WS71641/2 41/ / / WS / WS71651/2 51/ / WS / WS71661/2 61/ / / WS / A39

40 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps AB880 3 in. Porcelain Saddle AB881 4 in. Porcelain Saddle 21/4 in. A A Max. Cable Diam. Wt./C lb. AB AB /2 104 C755 Porcelain Cable Clamps Hole size A Hole Size A Wt./C lb. C7551A 3/8 19/16 50 C7551B 1/2 19/16 50 C7551C 5/8 19/16 50 C7552 3/4 25/32 91 C7552A 7/8 25/32 90 C7552B 1 25/32 85 C7552C 11/8 25/32 82 C /4 25/8 114 C7553A 13/8 25/8 110 C7553B 11/2 25/ C7553C 15/8 25/8 102 C /4 33/4 220 C7554A 17/8 33/4 214 C7554B 2 33/4 205 C7554C 21/8 33/4 200 C /4 41/4 260 C7555A 23/8 41/4 250 C7555B 21/2 41/4 243 Standard Finish GoldGalv with bronze hardware Also fits 11/2 in. wide channel. For minimum order quantities, contact your Regional Sales Office. Hole Size A Wt./C lb. C7555C 25/8 41/4 240 C /4 43/4 250 C7556A 27/8 43/4 240 C7556B 3 43/4 230 C7556C 31/8 43/4 220 C /4 513/ C7557A 33/8 513/ C7557B 31/2 513/ C7557C 35/8 513/ C /4 67/8 565 C7558A 37/8 67/8 550 C7558B 4 67/8 535 C7558C 41/8 67/8 520 C7558D 41/4 67/8 490 C7558E 43/8 67/8 475 C7558F 41/2 67/8 460 A40

41 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps S716 Cushioned Strip for Isolation and Vi bra tion Applications 15/8 in. For use with 701 O.D. tubing and pipe clamp. To determine 701 clamp size add 1/4 in. to O.D. tube size to allow for the Cushioned Strip material. 1/4 in. markings for fast measuring and cutting. Measurement chart is printed on back of carton. 20 feet included in each carton. Prevent metal to metal contact with the Cush ioned Strip material. It aids in sound in su la tion, shock absorption and protects against corrosion, distortion and abrasion. Cushioned Strip material is designed for optimal use between 1 C and 149 C (30 F and 300 F). Cushioned Strip material combined with the Superstrut 701 pipe strap can handle clamping assignments from 1/4 in. to 6 in. Order 701 clamp separately. C708U Short Strap for Channel or Wall Mount ing Standard Finish GoldGalv Example: C708U1/2 No clearance between pipe and channel. Carbon Steel Pipe Size A B Thickness Width Hole Size Design Load lb. Wt./C lb. 1/2 27/ /4 31/16 23/ /8 21/2 1/8 9/ /4 311/16 213/ /2 315/16 31/ /4 41/ /8 21/2 63/16 49/ /16 53/ /2 75/16 511/16 1/4 7/ /16 63/ /8 71/ /16 85/ A41

42 Pipe Straps, Pipe Clamps and Hangers Conduit and Cable Clamps C711 J Pipe Hanger Standard Finishes GoldGalv, Electrogalvanized (EG) Complies with Specification MSS SP69, Type 5. Hole provided for side mounting to wall as bracket. Example: C7111/2 Standard Pipe Size A Rod Size B C Overall Dimension D E F Bolt Size G Thickness Width Max. Rec. Load lb. 1/2 3/8 25/8 13/4 11/2 115/16 35/32 3/4 3/8 27/8 17/8 111/16 21/8 31/ /8 215/16 115/16 113/16 25/16 311/ /16 1/4 3/ /4 3/8 31/4 2 21/16 25/8 41/ ga 11/2 3/8 39/16 23/16 27/16 27/8 45/ /8 311/16 21/8 29/16 31/ /2 1/2 47/16 27/16 33/16 35/ /2 413/16 29/16 31/2 41/16 621/ /2 1/2 51/8 25/8 33/4 43/8 75/ /8 61/8 33/16 9/16 45/8 53/16 3/8 89/16 11/ /8 63/4 31/4 51/16 53/5 923/32 3/ * 3/4 73/4 39/16 513/16 65/8 111/ * 7/8 93/16 315/16 615/ / *Hangers 6 in. and over have hole instead of slot. Approx. Wt./C lb. 18 C727 Adjustable Ring Standard Finish Pregalvanized (no suffix) Carbon steel. For suspension of noninsulated pipe lines. Complies with Specification MSS SP69, Type 10. Example: C7271/2 Tube Size Rod Size A B C Thickness Width Approx Max. Rec. Load 1/2 31/8 25/8 13/8 9 3/4 31/8 21/2 11/ /8 25/8 11/8 9 3/8 16 ga /4 33/4 27/8 11/ /2 37/8 27/ / /2 53/4 41/4 15/ /2* 6 41/8 11/4 13/ /2 73/8 51/4 21/ ga 4 73/8 5 25/ /8* /8 21/4 11/ /4** 93/8 61/2 17/ *3/8 in. nut is used when NFPA rod sizing is requested. **1/2 in. nut is used when NFPA rod sizing is requested. Wt./C lb. A42

43 Pipe Straps, Pipe Clamps and Hangers Pipe Hangers C710 Adjustable Clevis Hanger Standard Finishes GoldGalv, Electrogalvanized (EG) Complies with Specification MSS SP69, Type 1. Example: C7101/2EG Pipe Size Size of Steel A B C D E F Max. Rec. Wt./C Upper Lower Load, lb. lb. 1/2 111/16 21/8 7/8 7/ /4 17/8 27/16 1 1/ /8 213/16 11/4 5/8 36 1/8x1 1/8x1 3/8 21/ /4 29/16 37/16 13/4 7/ / /8 11/ /16 47/8 215/16 15/ /2 411/16 61/8 313/ /16x11/4 1/2 43/4 69/ /8 13/ /2 3/16x11/4 415/16 615/16 41/16 13/ /16 713/16 41/2 115/ /4x11/4 5/8 31/ / /8 13/ /4x11/2 3/16x11/2 3/4 613/16 101/8 4 55/8 17/ /4x13/4 3/16x13/4 7/8 85/16 125/8 41/4 7 21/8 500 CL710 Light Duty Adjustable Clevis Hanger Standard Finishes GoldGalv, Bare (B), Electrogalvanized (EG), Fiberglass (FG). Carbon Steel Used on noninsulated, stationary pipelines. A lock nut above the clevis yoke is required for full rated load. Example: CL7103/8B Pipe Size Thickness of Steel A B C D E F Max. Rec. Wt./C Upper Lower Load, lb. lb. 3/8 17/8 23/16 21/2 11/4 9/ /2 13/4 23/16 21/2 11/8 9/ /4 16 ga x 7/8 16 ga x 7/8 17/8 21/4 21/2 11/4 1/ /8 23/16 23/4 21/2 11/2 3/ /4 25/8 33/8 21/2 13/ /2 3 37/8 21/2 21/4 13/ ga x 7/8 13 ga x 7/8 2 39/16 43/4 21/2 213/16 15/ /2 4 51/2 3 31/4 13/ /8 x 11/4 49/16 61/2 3 39/16 11/ /8 x 11/4 1/2 31/ /8 13/ /16 x 11/4 51/4 71/2 31/2 41/4 17/ /4x11/2 3/16x11/2 3/4 613/16 101/8 4 55/8 17/ /4x13/4 3/16x13/4 7/8 85/16 125/8 41/4 7 21/8 500 A43

44 Pipe Straps, Pipe Clamps and Hangers Pipe Hangers M718 Split Pipe Ring Standard Finishes Bare (B) or Electrogalvanized (EG) Malleable iron. For suspension of noninsulated, stationary pipelines. Example: M7183/8B Pipe Size 3/8 A B Max. Rec. Load, lb. Wt./C Approx. 13/ /2 7/8 13 3/ /8 11/ /4 15/ /2 17/ / /2 21/ /2 27/ / C725 Medium Pipe Clamp Standard Finishes GoldGalv, Bare (B), Electrogalvanized (EG) Carbon steel. For suspension of pipelines where little or no insulation is required. Complies with Specification MSS SP69, Type 23. Example: C7251/2B Pipe Size B C D E F H S Max. Rec. Load, lb. Wt./C Approx. 1/2 1 15/8 1 11/2 29 3/4 11/8 13/4 11/4 13/4 32 7/ /4 113/16 11/4 5/16 113/16 1/8 x /4 17/ / /2 15/8 1/2 21/16 11/2 21/ /8 31/8 21/ /2 25/16 9/16 35/16 21/2 31/ /2 1/4 x /4 33/4 23/4 35/ /2 37/8 5/8 33/4 3 37/ /16 3/4 41/4 35/16 5/8 41/4 1/4 x 11/ /8 7/8 57/8 5 3/4 53/ /8 x 11/ /8 3/4 67/ / /16 77/16 87/ /8 1/2 x /4 99/16 87/16 93/ Based on the allowable stresses shown in ANSI Code for pressure piping. For sizes 14 to 24, contact your Regional Sales Office. A44

45 Pipe Straps, Pipe Clamps and Hangers Pipe Hangers C720 Riser Clamp Standard Finishes GoldGalv, Bare (B) Available in sizes 1/2 in. through 10 in. Complies with Specification MSS SP69, Type 8. Example: C72011/2B Pipe Size A Thickness Width Bolt Max. Rec. Load, lb. Wt./Ea. Approx. 1/2 91/ /4 91/4 3/ / /4 97/ /8 x 11/ / / /2 111/ /16 1/ / /2 x 11/ / /2 x 13/ /16 11/ /8 5/8 x 21/ Standard Riser C726 Double Bolt Pipe Clamp Standard Finish Bare (B) Carbon Steel. For the suspension of insulated pipelines. Normally used with weldless eye nut. Example: C7261/2B Pipe Size B C D E F H S Max. Rec. Load, lb. Wt./C Approx. 3/4 11/16 33/16 21/2 111/ /8 1 11/2 33/4 21/2 3/8 21/16 3/16 x /4 11/2 3/4 311/16 27/8 21/ /2 113/16 47/8 33/4 213/ /4 511/16 411/16 33/ /2 25/8 61/2 53/8 5/8 31/2 1/4 x 11/ /4 11/16 67/8 6 33/ /2 3 71/16 63/ /8 75/8 61/2 41/ /4 3/8 x /16 81/ /4 915/16 89/16 61/ /16 1 3/8 x 21/ /4 1015/16 99/16 71/ A45

46 Pipe Straps, Pipe Clamps and Hangers Seismic Bracing C749N Seismic Brace Standard Finish GoldGalv C749N5/8 Seismic Brace Standard Finish GoldGalv 1650 lb. load safety factor 3 Wt./C 61 lb. C749N7/8 Seismic Brace Standard ard Finish GoldGalv 1650 lb. load safety factor 3 Wt./C 56 lb. C749N1 1/8 Seismic Brace Standard d Finish GoldGalv ES142 Standard Finish GoldGalv 1650 lb. bload safety factor 3 Wt./C 74 lb lb. load safety factor 3 Wt./C 72 lb. Bolt Dia. Wt./C lb. ES1421/2 x 11/2 1/2 21 Seismic bracing rod stiffener connector. Wt./C 21 lb. All braces have plastisol coating on the flat member. Plastisol insulates against vibration noise transmission and eliminates rattle at the connection points. A46

47 Hanger Accessories Other products available. Contact your Regional Sales Office. C704A Offset JHook M732H IBeam w/eye Nut M732/M732 Ext IBeam Clamp w/swing Nut C736 Light Welded Steel Bracket C739M Medium Welded Steel Bracket Sizes 1/2 in. thru 3 in. IPS MSS SP69 Type 28 Sizes 3/8 in. thru 7/8 in. Rod MSS SP69 Type 30 Max. Load 750 Lb. MSS SP69 Type 31 Max. Load 1500 Lb. MSS SP69 Type 32 C739H Heavy Welded Steel Bracket M750 Side Beam Bracket C785A Pipe Stanchion Saddle C786 Adj. Pipe Saddle Support C789 Steel Pipe Covering Protection Saddle Max. Load 3000 Lb. MSS SP69 Type 33 C790 Insulation Protection Shield for PVC coated pipe lines and insulated copper tubing Sizes 3/8 in. thru 7/8 in. Rod MSS SP69 Type 34 RC729A Single Pipe Roll Sizes 4 in. thru 36 in. IPS MSS SP69 Type 37 C729 Adj. Roller Hanger Sizes 21/2 in. thru 36 in. IPS MSS SP69 Type 38 S730C Pipe Roll + Base MSS SP69 Type 39 S730D Adj. Pipe Roll & Base Sizes 3/4 in. thru 12 in. IPS MSS SP69 Type 40 C769 Top IBeam Clamp Sizes 1 in. thru 24 in. IPS MSS SP69 Type 41 C755 T / C757 T Center IBeam Clamp Sizes 1 in. thru 20 in. IPS MSS SP69 Type 43 C780 Weld attachment as shown or inverted less bolt MSS SP69 Type 44 M778 Top Beam CClamp MSS SP69 Type 46 M777 Junior Top Beam CClamp Sizes 3/4 in. thru 7/8 in. Rod MSS SP69 Type 25 MSS SP69 Type 21 MSS SP69 Type 22 Sizes 3/8 in. thru 3/4 in. Rod MSS SP69 Type 19 Sizes 3/8 in. thru 1/2 in. Rod MSS SP69 Type 18 A47

48 Surface Raceway and Lighting Systems Material Superstrut electrical raceway, fixture hanging channel, closure strip and accessories are manufactured from hot rolled strip steel. Standard finish for the accessories is GoldGalv. Design Data Deflections at various hanger rod spacings for raceway channels based on 40 to 45 lb. per fixture. Deflection Channel at 10 ft. at 12 ft. at 14 ft. A1200 1/4 1/2 3/4 C1200 * 3/8 3/4 A1400 * Deflection Channel at 6 ft. at 7 ft. at 9 ft. B1200 3/8 9/16 5/8 B /2 * *Not recommended for this spacing. Electrical Raceway Superstrut channel together with snapin closure strip is listed by Un derwrit ers Laboratories as a surface metal race way. Other accessories listed by Underwri ters Laboratories are iden ti fied on the drawings. Wire Size AWG With or Without KO A1200 A1400 Maximum Number of Wires Raceway B1200 B1400 C1200 E1200 H1200 A B A B A B A B COLUMN A: Suitable for number of wires indicated when used as a raceway. Also suitable for number of wires indicated when installed to support and supply electrical fixtures when race way wiring is suitable for not less than 75 C. By providing clearance between fixture and raceway of not less than 1/2 in., where suitable for 60 C may be used. COLUMN B: Suitable for number of wires indicated when used as a raceway. Also suitable for number of wires indicated when installed to support electrical fixtures when clearance of not less than 1/8 in. is provided between race way and fixture and when wiring is suitable for 75 C. Applicable Channels A1200 B1200 A1200KO B1400 A1400 C1200 A1400KO E1200 H1200 A48

49 Surface Raceway and Lighting Systems Fixture Fittings 802 Raceway Joiner With Reinforcing Plate 822 Raceway Joiner & Seal A213 Inside Joiner Furnished complete with nuts. For Channel Wt./C lb. A802EG A Series 158 B802EG B Series 112 E802EG E Series 170 H802 H Series End Cap With Knockout Furnished complete with 1/4 in. x 5/8 in. machine screws and AB1001/4 nuts. A For Channel Wt./C lb. A /16 A Series 75 B822 7/8 B Series Tapped End Cap For A1200 Series channel. Only available in GoldGalv finish. A853 Channel Hanger KO for 1/2 in. conduit. Furnished complete with 1/4 in. x 5/8 in. flat head machine screw and AB1001/4 nut. For Channel Wt./C lb. A805EG A Series 21 H805EG H Series 31 A853L Channel Hanger Long 12 ga. steel. For 3/4 in. or 1 in. conduit. Furnished complete with 1/4 in. x 5/8 in. flat head machine screw and AB1001/4 nut. Rod Size For Channel Wt./C lb. A8093/4EG A Series 2 E8093/4EG E Series 26 A854 Channel Hanger Use hanger rod 3/8 in. or 1/2 in. Use with A, AR, B, BR or C Series single channel. Wt./C 25 lb. A854L Channel Hanger Long Long type for all Series channel. Wt./C 48 lb. Illustration showing A854 with nut and bolt furnished to attach to fluorescent fixture. Use with A, B, C or D Series channel. Wt./C 34 lb. Illustration showing A854L with nut and bolt furnished to attach to fluorescent fixture. Use with E and H Series channel as well as A, B, C or D Series channel. Wt./C 51 lb. A49

50 Surface Raceway and Lighting Systems Fixture Fittings AB844PGC Steel Closure Strip AB844PC Plastic Closure Strip Colour: Gold AB844PCGY Plastic Closure Strip Colour: Grey When used as a raceway, channel is normally installed with the slot up. After wiring has been completed the closure strip is installed. For all channels. Standard length: 10 ft. AB803 Cast Conduit Connector AB815 Swing Connector AB Swivel To connect 1/2 in. or 3/4 in. conduit to raceway channel. Furnished complete with stud nuts and hex nuts. Part has removable bushing to increase size from 1/2 in. to 3/4 in. Wt./C 60 lb. AB867 Spacer Nuts and bolts to clamp to channel is included. For 1/2 in. or 3/4 in. conduit. Wt./C 95 lb. AB866 Wiring Stud Nut Nuts and bolts to clamp to channel included. For 1/2 in. or 3/4 in. conduit. Wt./C 25 lb. For use with AB866 wiring stud nuts. Wt./C 24 lb. 1/2 in. Pipe thread Wt./C 21 lb. 811 Stud Nut 812 Stud Nut AB868 Fiber Retainer for Cables Until Closure Strip is In stalled For Channel Wt./C lb. 8111STR 1/4 x STR 1/4 x 11/4 9 For attaching fixture to slot down channel or to slot up knockouts. Specify length. Hex nut included. For Channel Wt./C lb. 8121EG 1/4 x 1 6 STD. PACK 100 Wt./C 3 lb. A50

51 Surface Raceway and Lighting Systems Kindorf Channel Boxes and Receptacles G2000 G2001 G2002 Finish GoldGalv Wt./C 110 lb. G2003 Finish GoldGalv Wt./C 120 lb. G2004 Finish GoldGalv Wt./C 120 lb. G1038 Duplex Outlet Finish GoldGalv Wt./C 130 lb. G1038A Single Outlet Finish GoldGalv Wt./C 140 lb. G1038D Raceway Outlet Complete unit including housing, standard DUPLEX 3wire, 15 Amp., 125 volt, ground receptacle and cover plate. Finish GoldGalv Wt./C 55 lb. G1038E Raceway Outlet Complete unit including housing, standard SINGLE 3wire, 15 Amp., 125 volt, ground receptacle and cover plate. Finish GoldGalv Wt./C 50 lb. G1038B Housing Only Complete unit including housing, duplex, 3wire, 15 amp., 277 volttwistlock receptacle and cover plate. Finish GoldGalv Wt./C 60 lb. G1038C Duplex Cover Plate G1038CA Single Cover Plate Complete unit including housing, single, 3wire, 15 amp., 277 volttwistlock receptacle and cover plate. Finish GoldGalv Wt./C 50 lb. G1038CX Blank Cover Plate Finish GoldGalv Wt./C 25 lb. Finish GoldGalv Wt./C 12 lb. Size of opening: diameter Finish GoldGalv Wt./C 14 lb. Finish GoldGalv Wt./C 15 lb. A51

52 Surface Raceway and Lighting Systems Kindorf Fixture Accessories G1017 Mercury Vapor Hanger G972HB1/2 Steel Fixture Hanger Adapter AB844 Closure Strip 111/16 A /64 313/64 11/8 dia. hole = 3/4 KO G9721¼2 Nipple G972HB1/2 & G972HB3/4 Fixture Hanger Adapter Finish GoldGalv To support high or low bay mercury vapor or heavy incandescent fixtures from raceway channels. Permits plugin connections with G1038 raceway outlets Used with Channel Depth Wt./C lb. A /4 76 Electrical Appllications 2 Finish GoldGalv The hanger adapter securely mounts the fixture hanger or box to the channel through the 1/2 in. KO in the base. No special tools are needed for installation of fittings and fixtures. Superstrut channels, with 1/2 in. KO s every 6 in., hangs and feeds the fixtures thereby simplifying installation. Wt./C 17 lb. Fixture Hanger Fixture Box and Fixture A854 AB288 E ES145 A1200P A52

53 Surface Raceway and Lighting Systems Electrical Appllications 822 G1038D H AB844 A853 A854 A853 AB803 AB AB A53

54 Surface Raceway and Lighting Systems Electrical Appllications A854 E A1200S G2004 G1038D G2003 A853 A854 AB844 A54

55 Right Angle Slotted Create the support framing you need Right Angle is manufactured from commercial quality steel in three different sizes. The small sizes are 14 ga. steel, the larger is 12 ga. steel. With this offering, an endless variety of metal framing requirements can be met, from lightweight suppor ting needs to larger shelving for inventory storage. One of the legs on all sizes is 15/8 in. wide, while the other is either 15/8 in., 23/8 in. or 31/8 in. long. Depending on the frame requirements, a single size can be utilized throughout, or the sizes can be interchanged to get the most efficient usage from the ma te ri al. This section will serve as a guide to plan and build your structure. Installation time is reduced inventory space is minimal Scribe marks are placed every 3/4 in. which saves planning, layout and cutting time and ensures accuracy. The ex clu sive slot and hole pattern, repeated every 3 in., is sci en tifi cal ly designed for ease of assembly and rigidity. No wel ding is necessary, no holes to drill. A 9/16 in. wrench is the only tool required for assembly. The proper nuts and bolts are included with the material to ensure fast and easy erection. Right angle metal framing is packaged in 10 and 12 lengths to minimize cut offs and ensure maximum use of material. 120 feet, 10, 12 foot lengths of right angle metal framing take up the same amount of space as one 2x4. A stan dard package includes 5 pieces to a bundle, sig nifi cant ly reducing handling and stor age space. The importance of cutting right angle easily, quickly and accurately is the key to time saving as sembly. The portable cutter provides these ad van tag es and makes layout and erection of any structure a lightwork job. Finish is designed for long lasting durability The standard GoldGalv hardware finish is applied to all Right Angle after rolling and punching of the holes.this provides you with a number of benefits. First, raw ends resulting from cuts will be protected by the sacrificial quality of zinc. Second, the edges of all holes are protected against formation of rust, to provide a call back free installation. Third, the electrogalvanizing provides an excellent bonding surface for paint if desired for aesthetic reasons. Note: Product is also available in pregalvanized (PG) sections. FLEXIBILITY SIMPLICITY ECONOMY A55

56 Right Angle Slotted Extra Nuts and Bolts RA Gauge RA Gauge RA Gauge Length ft. No. of ft./per Pkg. RA RA RA RA RA RA Each package includes 36 nuts and bolts. Package Std. 100 Sets Ctn. RABN5/8 23/8 in. 16 x 15/8 in. 100 Use with RA160 & RA225 RABN3/4 23/8 in. 16 x 3/4 in. 100 Use with RA300 RARC Rigid & Swivel Casters. Hard rubber composition 31/2 in. dia. with load rating of 225 lb. per wheel. RASC RAGP Gusset Plate For extra rigid assembly RAC Portable Cutter Package Std. Ctn. RAGP RARC 2 2 RASC 2 2 RAC 1 1 A56

57 Engineering Data & Specifications Design Data Channel TABLE 1 Elements of Sections Properties for Design Single Channels Nominal Thickness (inches) 12 ga = ga = ga = Double Channels LEGEND I Moment of inertia S Section Modulus r Radius of Gyration Z Nominal Axis A Area Section Member WT. lb./ft. H W A 2 I 4 XX AXIS S 3 r Z I 4 YY AXIS S 3 r Single Channel A B C D E H A B Double Channel A B C D E H A B TABLE 2 Maximum Pullout and Slip Loads for Steel Channel and Channel Nuts Channel Nuts Channel Pull Out Strenght Slip Resistance Torque Size / Thread All Series lb. kn lb. kn lb. kn 1/ /16 18 A B1200 3/8 16 C /2 13 D E1200 5/8 11 H / / A1400 5/ / B1400 1/ For aluminum channel the pull out load is calculated by multiplying the appropriate data by 50%. For slip resistance multiply by 75%. Maximum Pullout and Slip Loads for Fiber Glass Channel and Channel Nuts Channel Nuts Size / Thread Channel All Series Pull Out Strenght Slip Resistance Torque lb. kn lb. kn lb. kn 1/4 20 5/ /8 16 A /2 13 D A57

58 Engineering Data & Specifications Design Data Channel TABLE 3 Design loads for channel used as beam or column BEAM LOADS Table 3 contains simple beam, uniformlydistributed loads calculated at 25,000 psi material stress. Beam loads are based on channel being loaded across the xx axis. Loads are also listed at re duced deflections for long spans. Maximum loads at 25,000 psi stress Maximum allowable deflections and maximum uniform loads for all spans at 25,000 psi material stress. Reduced load for all 1/180 Span Deflection For moderate deflections on the longer spans, reduced loads are listed which will produce a de flec tion equal to 1/180 of the span. When maximum loads do not induce deflections ex ceed ing 1/180 x the span length reduced loads are not required. Reduced load for 1/360 Span Deflection For very slight deflections on the longer spans, reduced loads are listed which will produce a de flec tion equal to 1/360 of the span. When maximum loads do not induce deflections ex ceed ing 1/360 x the span length reduced loads are not required. Concentrated loads To obtain values for concentrated loads from Table 3, multiply uniform load by 0.5 and deflection by Slotted, Punched, or KO Channel Reduce load rating by 5%. COLUMN LOADS Allowable column loads given are for uniform axial loading with pinned ends. For eccentric loading or other end conditions reduce allowable loads according to standard engineering practice. DYNAMIC LOADS Allowable dynamic loads may be calculated by dividing the static loads shown in Table 3, by Maximum beam and column loading for special materials is multiplied with the following factors: Channel Type Beam Type Column Load Stainless Steel 1 1 Aluminum Warning Load tables, charts and design criteria provided in this section are intended as guides only. Selection of proper product, installation intervals, erection, and placement are the responsibility of the user. Thomas & Betts reserves the right to change material and finish specifications without notice, to improve its products. Long span deep beams Support in a manner to prevent rotation at supports and tie between supports to prevent twist. A58

59 Engineering Data & Specifications Design Data Channel TABLE 3 (cont d.) Single Channel Depth Maximum Uniform 1/180 Span 1/360 Span Col. Load Ga. Load Defl. Load Defl. Load Defl. 12 in. Beam or Column A /8 3, ,533 B /16 1, ,683 C /8 2, , D , ,670 E /16 6, ,830 H /4 10, ,106 A /8 2, , B / , in. Beam or Column A /8 2, ,2100 B / ,058 C /8 1, , D , ,930 E /16 4, ,482 H /4 7, ,693 A /8 1, , B / , in. Beam or Column A /8 1, ,842 B / ,315 C /8 1, , D ,050 E /16 3, ,082 H /4 5, ,277 A /8 1, , B / , in. Beam or Column A /8 1, ,419 B / ,465 C /8 1, ,040 8, D ,650 E /16 2, ,640 H /4 4, ,698 A / , B / ,420 When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lb. Double Channel Cat. No. Depth Maximum Uniform 1/180 Span 1/360 Span Ga. Load Defl. Load Defl. Load Defl. 12 in. Beam or Column A / Col. Load 21,177 B /8 12 3, ,110 C / , D ,312 E / ,623 H / ,210 A / , B /8 14 2, , in. Beam or Column A / ,609 B /8 12 2, ,440 C /4 12 4, , D ,942 E / ,926 H / ,390 A / , B /8 14 1, , in. Beam or Column A /4 12 4, ,974 B /8 12 1, ,670 C /4 12 3, , D , ,160 E / ,143 H / ,435 A /4 14 3, , B /8 14 1, , in. Beam or Column A /4 12 3, ,261 B /8 12 1, ,803 C /4 12 2, , D , ,480 E /8 12 7, ,259 H / ,395 A /4 14 2, , B / ,730 A59

60 Engineering Data & Specifications Design Data Channel TABLE 3 (cont d.) Single Channel Depth Maximum Uniform 1/180 Span 1/360 Span Col. Load Ga. Load Defl. Load Defl. Load Defl. 36 in. Beam or Column A /8 1, ,962 B / ,498 C / , D ,335 E /16 2, ,160 H /4 3, ,132 A / , B / , in. Beam or Column A /8 1, ,466 B / ,579 C / , D ,280 E /16 1, ,698 H /4 3, ,514 A / , B / , in. Beam or Column A / ,943 B / ,981 C / , D ,439 E /16 1, ,092 H /4 2, ,850 A / , B / , in. Beam or Column A / ,369 B / ,555 C / , D ,012 E /16 1, ,123 10,505 H /4 2, ,150 A / , B / ,250 When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lb. Double Channel Depth Maximum Uniform 1/180 Span 1/360 Span Col. Load Ga. Load Defl. Load Defl. Load Defl. 36 in. Beam or Column A /4 3, ,470 B /8 1, ,840 C /4 2, , D , ,057 E /8 6, ,316 H / ,265 A /4 2, , B / , in. Beam or Column A /4 2, ,635 B / ,790 C /4 2, , D , ,042 E /8 5, ,272 H / ,025 A /4 1, , B / , in. Beam or Column A /4 2, ,730 B / ,640 C /4 1, , D , ,387 E /8 4, ,170 H / ,700 A /4 1, , B / , in. Beam or Column A /4 2, ,763 B / ,405 C /4 1, ,263 13, D ,391 E /8 4, ,980 H /2 7, ,280 A /4 1, , B / ,580 A60

61 Engineering Data & Specifications Design Data Channel TABLE 3 (con d.) Single Channel Depth Maximum Uniform 1/180 Span 1/360 Span Col. Load Ga. Load Defl. Load Defl. Load Defl. 60 in. Beam or Column A / ,762 B / C / , D ,561 E /16 1, ,874 H /4 2, ,406 A / , B / in. Beam or Column / ,127 B / C / , D ,280 E /16 1, ,211 H /4 1, ,616 A / , B / in. Beam or Column A / ,436 B / C / , D ,084 E /16 1, ,509 H /4 1, ,313 10,782 A / , B / in. Beam or Column A / ,061 B / C / , D E / ,991 H /4 1, ,988 A / , B / When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lb. Double Channel Depth Maximum Uniform 1/180 Span 1/360 Span Col. Load Ga. Load Defl. Load Defl. Load Defl. 60 in. Beam or Column A /4 1, ,738 B / ,100 C /4 1, ,023 13, D ,531 E /8 3, ,734 H /2 6, ,810 A /4 1, , B / , in. Beam or Column A /4 1, ,347 13,646 B / ,055 C /4 1, , D ,581 E /8 3, ,415 H /2 5, ,230 A /4 1, , B / , in. Beam or Column A /4 1, ,132 12,500 B / ,230 C /4 1, , D ,230 E /8 3, ,023 H /2 5, ,560 A /4 1, , B / , in. Beam or Column A /4 1, ,992 B / C /4 1, , D ,842 E /8 2, ,993 H /2 4, ,975 A / , B / ,370 A61

62 Engineering Data & Specifications Design Data Channel TABLE 3 (cont d.) Single Channel Depth Maximum Uniform 1/180 Span 1/360 Span Col. Load Ga. Load Defl. Load Defl. Load Defl. 96 in. Beam or Column A / ,108 B / C / , D E / ,423 H /4 1, ,059 A / , B / in. Beam or Column A / ,456 B / C / D E / ,291 H /4 1, ,579 A / , B / in. Beam or Column A / B / C / D E / ,478 H /4 1, ,521 A / B / in. Beam or Column A / C / E / H / A / When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lb. Double Channel Depth Maximum Uniform 1/180 Span 1/360 Span Col. Load Ga. Load Defl. Load Defl. Load Defl. 96 in. Beam or Column A /4 1, ,675 B / C / , D ,942 E /8 2, ,917 10,875 H /2 4, ,120 A / , B / in. Beam or Column A /4 1, ,071 B / , C / , D ,324 E /8 2, ,515 8,599 H /2 3, ,160 A / , B / in. Beam or Column A / B / C / , D ,883 E /8 1, ,227 6,946 H /2 3, ,040 A / , B / in. Beam or Column A / B / C / E /8 1, H /2 2, ,873 A / B / A62

63 Engineering Data & Specifications Design Data Channel TABLE 3 (cont d.) Single Channel Depth Maximum Uniform 1/180 Span 1/360 Span Ga. Load Defl. Load Defl. Load Defl. 168 in. Beam or Column Col. Load Double Channel Depth Maximum Uniform 1/180 Span 1/360 Span Ga. Load Defl. Load Defl. Load Defl. 168 in. Beam or Column Col. Load A / C / E / H / A / in. Beam or Column E / H / in. Beam or Column E / H / in. Beam or Column E / H / When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lb. A / B / C / E /8 1, , H /2 2, ,326 A / B / in. Beam or Column A / C / E /8 12 1, H /2 2, ,053 A / in. Beam or Column A / C / E /8 12 1, H /2 1, A / in. Beam or Column A / C / E / H /2 1, A / A63

64 TABLE 4 Safe bearing loads for 15/8 in. channel and combinations. Safety factor of 21/2 Engineering Data & Specifications Design Data Channel Section Recommended Load in lb. A A B B C E H Section Recommended Load in lb. A A B B C E H Section Recommended Load in lb. A A B B C E H TABLE 5 Design load table for typical channel connections. Safety factor of 21/2 based on ultimate strength of the connection. Load diagrams indicate up to three design loads, for 12 gauge and 14 gauge channel applications. 90 Fittings (When used in position shown) Both ends supported Both ends supported AB202 A lb. A lb. AB203 A lb. A lb. AB201 AB lb. 700 lb. Both ends supported Both ends supported AB202 A lb. A lb. AB213 A lb. AB214 A lb. AB lb. Both ends supported Both ends supported Flat Plate Fittings Both ends supported AB205 A lb. AB216 A lb. AB204 A lb. AB215 A lb. AB206 A lb. A lb. A64

65 Engineering Data & Specifications Design Applications CANTILEVER BEAMS SIMPLE BEAMS BEAMS FIXED ON ONE END, SUPPORTED AT THE OTHER END BEAMS FIXED AT BOTH ENDS A65

66 TABLE 6 Engineering Data & Specifications Design Applications Conversion Factors for Beams with Various Static Loading Conditions Load tables on pages A59 through A63 for A, B, C, E, and H Series channel are for single span beams supported at the ends. These can be used in the majority of cases. There are times when it is necessary to know what happens with other loading and support conditions. Some common arrangements are shown in Table 6. Simply multiply the loads from the Design Load Tables times the factors given in Table 6. LOAD AND SUPPORT CONDITION LOAD FACTOR DEFLECTION FACTOR 1. Simple Beam Uniform Load Simple Beam Concentrated Load at Center Simple Beam Two Equal Concentrated Loads at 1/4 Points Beam Fixed at Both Ends Uniform Load Beam Fixed at Both Ends Concentrated Load at Center Cantilever Beam Uniform Load Cantilever Beam Concentrated Load at End Continuous Beam Two Equal Spans Uniform Load on One Span Continuous Beam Two Equal Spans Uniform Load on Both Ends Continuous Beam Two Equal Spans Concentrated Load at Center of One Span Continuous Beam Two Equal Spans Concentrated Load at Center of Both Spans A66

67 Engineering Data & Specifications Design Applications EXAMPLE I PROBLEM: Determine the load and deflection of an A1200 beam continuous over one support and loaded uniformly on one span. SOLUTION: A. From load table 3 for A1200 the load for a 5 ft. 0 in. span is 706lb. and deflection is in. B. Multiply by factors from Table 6. Load = 706 lb. x 1.30 = lb. Deflection = x 0.92 = in. COLUMN LOADING The load bearing capacity of column or compression members is a function of the inherent configurational strength, the unbraced length and design of the end connections. Values of axial column loading given in Table 3 were calculated using a rotationally free and translation fixed correction at each end (see illustration I). This gives an end condition constant (K) of 1. EXAMPLE II PROBLEM: Determine load and deflection of an E1200 cantilever beam with a concentrated load on the end. SOLUTION: A. From load table 3 for E1200 the load for a 3 ft. 0 in. span is 2216 lb. and deflection is in. B. Multiply by factors from Table 6. Load = 2216 lb. x.12 = lb. Deflection x 3.20 = in. If other end conditions are used, axial loading should be cal cu lat ed using procedures in the AISI specification for the design of cold formed steel structural members (SG671) and the en gi neer ing values for Superstrut channel given in Table 1. COLUMN HEIGHT ILLUSTRATION I END CONDITION CODE Rotation fixed and translation fixed Rotation free and translation fixed K value Rotation fixed and translation free TABLE 7 Load Carrying Capacities of Hot Rolled Steel Rod Design Load lb. Nominal Root Area for Serv. Temperature Rod Dia. Thread 343 C 399 C (650 F) (750 F) 3/ / / / / Safety factor of 5. TABLE 8 Rod Size Determined by Pipe Size for Fire Protection Pipe Size Rod Size 3/4 to 2 3/8 21/2 to 31/2 1/2 4 to 5 5/8 6 3/4 8 to 12 7/8 A67

68 Design Applications TABLE 9 Maximum Spacing between Pipe Supports Engineering Data & Specifications Steel Pipe Nom. Pipe Size Max. Spacing (ft.) Copper Pipe Nom. Pipe Size Max. Spacing (ft.) 1/2 3/4 1 11/2 2 21/2 3 31/ /2 3/4 1 11/4 11/2 2 21/2 3 31/ TABLE 10 Minimum Spacing (inches) between Centers of Standard Pipe When Using Superstrut #702 Pipe Straps Nom. Pipe Size 1/2 3/4 1 11/4 11/2 2 21/2 3 31/ /2 13/16 3/4 15/16 17/ /2 15/8 13/4 11/4 13/4 17/8 2 21/4 11/2 115/16 21/16 23/16 27/16 29/ /16 25/16 21/2 23/4 27/8 31/8 21/2 27/16 29/16 23/4 3 31/8 33/8 35/ /16 215/16 31/16 35/16 37/16 33/4 4 45/16 31/2 31/8 31/4 33/8 35/8 33/4 41/16 45/16 45/8 415/ /16 39/16 315/16 41/16 43/8 45/8 415/16 51/4 59/ /4 47/8 5 51/4 53/8 55/8 57/8 63/16 61/2 613/16 77/16 81/8 8 57/ /8 63/8 61/2 63/4 7 75/16 75/8 8 89/16 91/4 103/8 A68

69 Engineering Data & Specifications Design Applications TABLE 11 Standard Dimensions and Weights of Piping Materials and Conduit Mechanical (ANSI & API Standard, Schedule 40) Nominal Std. Pipe Size Pipe O.D. Coupling O.D. Weight of Pipe lb./ft. Weight of Pipe Filled w/water lb./ft. 1/ / / / / / Electrical Conduit Nominal Conduit Size Conduit O.D. Rigid Steel Weight of Conduit lb./ft. Weight of Conduit w/nonlead Covered Conductor lb./ft. Conduit O.D. Thin Wall (EMT) Weight of Conduit lb./ft. 1/ / / / Includes weight of heaviest conductor combination. A69

70 TABLE 12 Extra Strong Pipe (ANSI & API Standard, Schedule 80) Engineering Data & Specifications Design Applications A.S.A. B36.10 SCHEDULE NOS. AND NOMINAL WALL THICKNESS DESIGNATIONS EXTRA STRONG PIPE and SCHEDULE 80 PIPE (through 8 in.) Nominal Pipe Size O.D. Wall Thickness I.D. Weight of Pipe lb./ft. Water Weight per ft. of Pipe lb. Weight of Pipe Filled w/water lb./ft. 3/ / / / / / / EXTRA STRONG PIPE (10 in. through 24 in. OD) SCHEDULE 80 PIPE (10 in. through 24 in. OD) OD OD OD OD OD OD OD OD OD OD TABLE 13 Pipe Covering Weights (Thickness intended as guide, only) Nominal Pipe Size Thick lb./ft. Thick. lb./ft. Thick. lb./ft. Thick / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Thickness and weight of calcium silicate covering. lb./ft. Thick. lb./ft. Thick. lb./ft. Thick. lb./ft. A70

71 Engineering Data & Specifications Design Applications TABLE 14 Column Loading For Rack Construction Typical general storage rack for use with plywood or other decking. Column height, equal shelf spacing GENERAL STORAGE RACKS PALLET RACKS BARREL RACKS BULK FURNITURE RACKS CABLE RACKS BAR STOCK RACKS DISPLAY RACKS SPECIAL PURPOSE RACKS For Uniform Loads on Horizontal Members, See Table 3 Allowable load in lb. per upright Column Number of Shelves per upright Height A A B B A A B B A A B B A A B B A A B B A71

72 Engineering Data & Specifications Design Applications Mechanical Support Example 1 Example 2 B302 CONCRETE INSERT B302 CONCRETE INSERT AB ANGLE E1421/2 x 100 HEX.H.BOLT B1001/2 SPRING NUT S25612 BRACKET S20314 a BRACKET a 30 a 60 AB2392 BRACE a A1202 S24920 BRACKET CHANNEL a= E1421/2 in. x 100 AA1001/2 SPRING NUT E1421/2 x 100 HEX.H.BOLT B1001/2 SPRING NUT Suspended column, carrying brackets, braced to the ceiling. B1001/2 SPRING NUT E1421/2 x 100 HEX.H.BOLT A1001/2 SPRING NUT AB ANGLE A1202 CHANNEL B1202 CHANNEL AB ANGLE A1202 CHANNEL Suspended column, holding bracket and console braced to wall. Example 3 Example 4 US562 H.D. BEAM CLAMP Trapeze with channels as cross members using beam clamps and hanger rods. AB241 SQ. WASHER A1200 CHANNEL U568 SAFETY STRAP U560 H.D. BEAM CLAMP E1451/2 HEX. NUT A1200 CHANNEL H1041/2 x 10 HANGER ROD A1200 CHANNEL H1041/2 x 10 HANGER ROD E1451/2 HEX. NUT S20221 CROSS MEMBER Sketch depicts the use of beam clamps on slanted beams. Example 5 Example 6 SI4001/2 SPOT INSERT B302 CONCRETE INSERT E1421/2 x 100 HEX.H.BOLT B1001/2 SPRING NUT AB ANGLE B1602 CHANNEL B1600 CHANNEL Trapeze, constructed from channels, fittings. The use of spot inserts is shown (SI4001/2). H1041/2 x 10 HANGER ROD C7811/2 SQUARE WASHER E1451/2 HEX. NUT H1191/2 ROD COUPLING H1191/2 ROD COUPLING A1001/2 SPRING NUT Trapeze with S202 cross members using hanger rods and concrete inserts. A72

73 Engineering Data & Specifications Design Applications Mechanical Support Example 7 Example 8 31/2 MIN. U514 CLAMP BRACKET 53/4 in. MIN. A1001/2 SPRING NUT E1421/2 X 100 HEX.H. BOLT S256 CHANNEL BRACKET U514A CLAMP BRACKET A1200 CHANNEL Singlesided bracket application X289 CORNER FITTING Singlesided bracket application A1001/2 SPRING NUT A1200 CHANNEL AB ANGLE SUPPORT FITTING E1421/2 X 100 HEX.H.BOLT S25618 CHANNEL BRACKET * NOTE: BRACE SHOULD BE USED FOR LENGTHS GREATER THEN 30 IN. A1200 CHANNEL Example 9 Example 10 A597 BEAM CLAMP BRACKET A1200 CHANNEL A1001/2 SPRING NUT AB254LCORNER FITTING 90 INS. LEFT. E142 1/2 X 100 HEX.H. BOLT A597 BEAM CLAMP BRACKET E1421/2 X 100 HEX.H. BOLT A1202 CHANNEL S24920 BRACKET A1200 CHANNEL AB CORNER FITTING LEFT. Twosided heavy duty application A1001/2 SPRING NUT Heavy duty bracket application AB ANGLE E1421/2 X 100 HEX.H. BOLT S24920 BRACKET E1421/2 X 100 HEX.H. BOLT AB2392 BRACE A1200 CHANNEL Example 11 Example 12 U514 CLAMP BRACKET A1001/2 SPRING NUT X289 CORNER FITTING U514 CLAMP BRACKET E1421/2 X 100 HEX.H. BOLT A1202 CHANNEL A1202 CHANNEL X289 CORNER FITTING A1001/2 SPRING NUT A1200 CHANNEL AB ANGLE SUPPORT FITTING E1421/2 X 100 HEX.H. BOLT S20320 BRACKET Brackets parallel to beam Brackets perpendicular to beam S20320 BRACKET A1202 CHANNEL A73