T A POOL ASSEMBLY AND INSTALLATION MANUAL. Above Ground 52 Round Pools

Transcription

1 T SSEMBLY ND INSTLLTION MNUL bove Ground 52 Round Pools Note: Deck and fence accessories shown are optional. THIS MNUL EXPLINS THE CORRECT METHOD TO SSEMBLE YOUR NEW SWIMMING. RED THESE INSTRUCTIONS ND STUDY THE ILLUSTRTIONS. LSO RED INSTRUCTIONS FOR CCESSORIES SUCH S FILTERS, LDDERS, ETC. PY PRTICULR TTENTION TO THE CUTIONS ON THE FOLLOWING PGES. THE MNUFCTURER IS NO T FFILITED WITH NY PROFESSIONL INSTLLER, THEREFO RE THE MNUFCTURER CNNO T SSUME RESPONSIBILITY FOR ERRORS IN THE INSTLLTIO N OF YOUR BY THE INSTLLER O R THE HO MEOWNER. IF Y OU HVE THIS PO OL INSTLLED BY OTHERS, PLESE SUPERVISE TO BE SURE Y OUR IS INSTLLED PRO PERLY ND THT LL THE CUTIO NS LISTED THRO UGHOUT THIS MNUL HVE BEEN FOLLOWED. PST EXPERIENCE O R SHO RT CUTS MY NO T BE COMPTIBLE WITH OUR S, FOLLOW THE INSTLLTION MNUL. THE MNUFCTURER RESERVES THE RIGHT TO CHNGE OR IMPRO VE NY ITEM WITHOUT INCURRING NY OBLIGTION TO MKE NY CHNGES OR IMPROVEMENTS ON ITEMS PREVIOUSLY SOLD ND TO DISCONTINUE MODELS OR CHNGE SPECIFICTIONS T NY TIME WITHOUT NOTICE. THIS PRODUCT IS SOLD WITH "LIMITED WRRNTY ". THE TERMS ND CONDITIONS RE SET FORTH IN THE "LIMITED WRRNTY " CERTIFICTE PCKED WITH ECH. COPIES OF THE "LIMITED WRRNTY" RE LSO VILBLE UPON WRITTEN REQUEST. YOUR LO CL BUILDING CO DE MY REQ UIRE O BTINING BUILDING PERMIT ND MY HVE REQUIREMENTS ON SETBCKS, BRRIERS, ETC. NY HO ME BUILT O R PREFBRICTED DECKS SH OULD CONFORM TO THE LOCL CODES, ND BOC NTIONL BUILDING CODE. THE ELECTRICL CODE MY REQUIRE PERMIT ND INSPECTIO N, ND USE O F G FCI DEVICES O R O THER CONDITIONS. THE ELECTRICL INSTLLTION MUST LSO CONFORM TO RTICLE 680 OF THE NTIONL ELECTRIC CODE. INSTLL THE FILTER ND PUMP IN CCORDNCE WITH THE MNUFCTURERS INSTRUCTIONS. RTICLE 680 STTES THT YOU MUST BOND THE SWIMMING PUMP TO THE SWIMMING. THIS CN BE DONE BY TTCHING #8 COPPER WIRE FROM THE BONDING LUG ON THE PUMP TO N UNPINTED METL SURFCE ON THE OR BOTTOM CLIP. THE INSTLLTION OF N BOVE GROUND SWIMMING WILL USULLY REQUIRE THREE PEOPLE TO HELP SSEMBLE IT. DNGER: THIS, EVEN IF SUPPLIED WITH DEEP RE, CONFORMS TO THE NTIONL SWIMMING INSTITUTE STNDRDS FOR TYPE O, NON-DIVING. DIVING, SLIDING OR JUMPING INTO THE MY CUSE PRLYSIS, DETH OR PERMNENT INJURY.

2 DNGER 1. DO NOT DIVE OR JUMP INTO Y OUR. DO NOT USE SLIDE ON THIS. YOUR CONTINS SHLLOW WTER ND IS NOT DESIGNED FOR HEDFIRST ENTRY (DIVING OR SLIDING) OR JUMPING. DIVING, SLIDING OR JUMPING CNRESULT IN BROKEN NECK IF YOU STRIKE THE. THIS CN RESULT IN PRLYSIS, DETH OR PERMNENT INJURY. INFORM LL FMILY ND GUESTS OF THESE RULES ND POINT OUT WRNING LBELS. 2. IT IS NECESSRY TO MINTIN 4 HIGH BRRIER TO REDUCE THE CHNCE OF CHILD CCESSING N UNSUPERVISED. THE BRRIER MY BE FENCE,, OR COMBINTION TH EREOF WHICH COMPLETELY SURROUNDS THE. BRRIERS MUST COMPLY WITH THE LOCL BUILDI NG CODE, BOC NTIONL BUILDING CO DE OR THE CONSUMER PRODUCT SFETY COMMISSION BRRIER STTEMENT. THE FO UR FOOT HIGH S USULLY PROVIDE THIS BRRIER, HOWEVER IF THE IS LESS THN 48 BO VE GRDE, OR HS BUTTRESSES (OVL S), YOU MY NEED DDITIONL FENCING TO PROVIDE THIS BRRIER. CONSULT WITH Y OUR BUILDING O FFICIL FO R SPECIFIC REQ UIREMENTS. FENCING O PTIONS RE VILBLE FOR YOUR, PLESE CONTCT YOUR DELER. 3. Y OU MUST MINTIN 5 WIDE CLER ZONE ROUND TH E ND DECK OR FENCING. DO NOT LLOW TOYS, CHIRS, TBLES OR SIMILR CLIMBBLE OBJECTS IN THIS CLER ZO NE, ENBLING CHILDREN TO CLIMB ND G IN CCESS TO THE. THE FILTER EQUIPMENT MUST LSO BE LOCTED OUTSIDE OF THE CLER ZONE. 4. YOU MUST RISE ND LTCH, OR SECURE YOUR LDDER OR ENTRNCE WHEN THE IS NOT IN USE. dherence to the above items will reduce the frequency of preventable child drownings in swimming pools. WRNING 1. YOUR IS SUPPLIED WITH WRNING SIGNS, WHICH MUST BE FFIXED TO THE S SPECIFIED. IF YOU BUILD DECK, THE TWO RE SIGNS MUST BE FFIXED TO THE DECK T THE POINT OF ENTRY, VISIBLE TO PEOPLE ENTERING THE RE. FILURE TO INSTLL OR IMPROPER LOCTION OF SFETY INFORMTION WILL SUBJECT YOU ND/OR THE INSTLLER TO LIBILITY RISING FROM INJURY CLIMS.. NO DIVING COPING: ( TWO SUPPLIED ) THESE RE TO BE INSTLLED CROSS THE FROM THE POINT OF ENTRY, ND HVE ONE SECTION OF REGULR COPING BETWEEN THEM. B. COPING WITH INTERNTIONL LOGO: THIS ONE COPING IS TO BE INSTLLED T THE POINT OF ENTRY, EITHER DJCENT TO THE LDDER, UNDER THE IN LDDER, OR IN THE CENTER OF DECK. C: DNGER RE SIGN WITH LOGO: ( T1440) THIS SIGN MUST BE INSTLLED T THE POINT OF ENTRY, FCING LL USERS S THEY ENTER THE PO OL. IF Y OUR HS FENCE, THE SIG N IS TO BE FSTENED TO THE FENCE, DJCENT TO THE LDDER OR ENTRNCE. IF YOUR DOES NOT HVE DECK O R FENCE, TTCH THE SIGN TO THE EDGE OF THE COPING DJCENT TO THE LDDER. THE SIGN MUST BE VISIBLE TO LL USERS S THEY ENTER THE RE. D. CUTION - SFETY RULES SIGN: (1445) THIS SIGN MUST BE TTCHED TO THE FENCE DIRECTLY BELOW THE DNGER SIGN OR IF YOU DO NOT HVE FENCING, ON THE COPING NEXT TO THE DNGER SIGN. If any signs are missing or damaged contact the customer service department for replacements. CUTION 1. DECK SURFCES MY BECOME SLIPPERY WHEN WET. DO NOT RUN OR DIVE INTO THE FROM THE DECK. NOTE: SUNTN LOTIONS ND OILS MY CUSE COMPONENTS TO BECOME SLIPPERY. 2. ECH MONTH CHECK THE FOR DETERIORTION OR LEKGE, ESPECILLY T THE SKIMMER ND RETURN FITTINGS. THE SKIMMER ND RETURN GSKETS SHOULD BE REPLCED ECH SPRING TO PREVENT LEKGE. DETERIORTION CN WEKEN THE WHICH COULD RUPTURE, RELESING THE WTER WHICH COULD CUSE BODILY HRM ND PROPERTY DMGE. 3. FOR NIGHTIME USE, YOU MUST PROVIDE LIGHTING TO ILLUMINTE THE, SFETY SIGNS, ND DECK SURFCES. LIGHTING MUST COMPLY WITH RTICLE 680 OF THE NTIONL ELECTRIC CODE. IT IS IMPORTNT THT USERS BE BLE TO SEE THE SHLLOW DEPTH OF THE T LL TIMES. 4. THE FOLLOWING BSIC LIFESVING EQUIPMENT MUST BE ON HND T LL TIMES:. LIGHT BUT STRONG POLE ( SHEPHERD S CROOK ) NOT LESS THN 12 LONG. B. 1/4 THROWING ROPE, S LONG S 1 1/2 TIMES THE MXIMUM WIDTH OF THE, WHICH IS TTCHED TO COST GURD PPROVED FLOTTION DEVICE SUCH S RING BUOY. 2 C. TELEPHONE SHOULD BE NERBY WITH LIST OF EMERGENCY TELEPHONE NUMBERS, SUCH S POLICE, & MBULNCE

3 5. DDITIONL SFETY RELTED PUBLICTIONS RE VILBLE FROM THE FOLLOWING: NTIONL SP ND INSTITUTE CONSUMER PRODUCT SFETY COMMISSION 2111 EISENHOWER VE WSHINGTON, DC LEXNDRI, V IMPORTNT INSTLLTION ITEMS 1. LEVELNESS; MUST BE LEVEL WITHIN 3/4. UNLEVEL S PLCE EXTREME FORCES ON THE WHICH MY DEFORM. 2. CLOSURE; THE MUST BE FSTENED TOGETHER PROPERLY WITH BOTH BRS ND FSTENERS IN LL HOLES. OMITTED BRS OR FSTENERS CN CUSE THE TO RUPTURE, DESTROYING THE ND INJURING PEOPLE. 3. SND COVE; THIS SUPPORTS THE ND MUST BE PCKED SOLID. IF IT COMPRESSES, SHIFTS OR ERODES THE MY RUPTURE, RELESING LL THE WTER ND DESTROYING THE ND INJURING PEOPLE. 4. THESE S RE NOT DESIGNED TO BE BURIED. THE GROUND FORCES CN COLLPSE THE INWRD. 5. DO NOT LOCTE YOUR NER STRUCTURES SUCH S HOUSE, GRGE, ETC. S PEOPLE COULD DIVE OR JUMP INTO THE RESULTING IN DETH OR PERMNENT INJURY. 6. LTHOUGH THERE RE RELTIVELY FEW PRTS IN YOUR, NONE MY BE OMITTED IN SSEMBLY. ECH PRT SUPPLIED IS N IMPORTNT PRT ND IF OMITTED, MY CUSE FILURE. CHECK LL PRTS GINST THE PRTS LIST. WRNING: Do not exceed the following torque values for the noted fasteners: 1/4-20 S. S. Fasteners 75 (in. lbs.) 3/8-16 S. S. Fasteners 236 (in. lbs.) 3/8-16 luminum Fasteners 143 (in. lbs.) TOOLS ND MTERILS PHILLIPS SCREWDRIVER #2 HND TROWEL EXTENSION CORD HMMER RKE SLOTTED SCREWDRIVER #2 GRDEN HOSE & NOZZLE STRING LINE PLIERS SOCKET WRENCH & SOCKETS 50 TPE MESURE HND TMPER TORQUE WRENCH TRNSIT OR FRM LEVEL ELECTRIC DRILL & BITS GRDEN SHOVEL WRENCHES 1 LONG STRIGHT 2 X 4 14 LONG 1 ROLL DUCT OR FBRIC TPE 25 WOOD STKES I CN WHITE SPRY PINT SND ND BLOCK CHRT SND 2 x 8 x 16 4 x 8 x 16 P OOL SIZE TONS YRDS PTIO BLOCKS CP BLOCKS 15' 2 1 1/ ' 2 1/2 1 3/ ' 3 1/2 2 1/ ' 4 1/ ' 5 3/4 3 3/ NOTE: Sand must be masons or bar sand and be free of foreign objects SELECTING THE SITE 1. Check your local building codes and acquire proper building permits. For poor soil conditions consult a professional engineer. 2. The pool site must be absolutely level and solid. The area must be free from stones and roots. 3. To protect the pool from chemicals and foreign matter in the soil, you may use a ground cover under the sand base. Do not install your pool on asphalt, tar paper, grass, wood, gravel, clay, or concrete, or treated soils. 4. Position your pool away from trees, overhead wires, structures such as a house or garage or septic field. GROUND PREPRTION Your pool must be installed on a solid level surface. Posi tion stakes as shown on figure 1 and use a farm level or transit to level the area shown. Remove all grass, roots and stones. Start at the lowest spot level outwards, do not fill in low spots. The area must be absolutely level. The following table refers to Figures 1 and 3 on the next page. ROUND S LINE 1 LINE

4 SECTION II CONSTRUCTION Step 1: Parts Identification: Se e figures in bill of material packet. Check for installation addendums. LINE 2 LINE 1 STKE LEVEL GROUND PREPRTION RE: REMOVE LL GRSS, ROOTS, STONES ND DEBRIS *SLOT SIDE UP* Step 2: See Figures 1 and 2 and table on page 3. Scribe a circle defined by line 1. Slide the wall channel s into the bottom clips and position them on the circle. Place a patio block under eac h bottom clip. If th e bottom wall channel i s on soft ground, place additional blocks in a pyramidal shape unde r the bottom c lips for support. FIGURE 1 L00033 TRNSIT FOLLOWS LINE 2 FOR LUMINUM S FIGURE 2 SMLL STKE L00033B SMLL STKE BOTTOM CLIP BOTTOM CHNNEL 2 X 8 X 16 PTIO BLOCK BOTTOM CHNNEL BOTTOM CLIP Dig 2 down for each block. The top of each block must be at grade level. When leveling the blocks, never build up; always dig down. Place a stake at the center of each wall channel to keep the circle round during installation. FOR STEEL S FOLLOWS LINE 2 2 X 8 X 16 PTIO BLOCK Step 3: See Figure 3, 4 and 5. Place the required amount of sand inside the pool area. St arting at the center of a bottom clip, insert the pool wall into the wall channel around the entire pool area. Make sure the skimmer and return cutout are at the top of the wall and not over a clip or upright. ttach the pool wall ends together as shown using the two (2) wall enclosure bars and hardware. The heads of the machine screws must be on the inside of the wall. Do not omit any fasteners in the pool wall connection. The wall will not stay together without all the fasteners. Cover the bolt enclosure on the inside with several layers of duct tape to protect the liner. If either wall enclosure strip is missing, damaged or do not align properly with all holes in the wall, do not use the wall and notify your dealer at once. CUTION: Installation of the wall in any other manner than precisely described above will cause extensive damage to the pool and may result in injury or death to those people in or around your pool. pool to insure that it has not shifted during assembly. NOTE: If the wall does not stay in the wall channel, the ground is not level - remove the wall and level the wall channel. fter the pool wall is assembled, check the dimensions of the Step 4: See Figure 6. ttach the uprights to the bottom clips addendum in Bill of Material packet. as shown. If pool is provided with feature strips see Step 5: See Figure 6 and Detail 6a. Install the skimmer throat gasket to each side of the pool wall and attach the skimmer to the wall as shown using hardware provided with the skimmer. Mount the skimmer at the center with only two (2) pan head screws at this point. Refer to skimmer instruction sheet. 4 If a pool fence or deck is to be installed, read those manuals before proceeding. Check care and maintenance manual for proper placement of safety information.

5 Step 6: See Figure 7. Spread the sand across the entire bottom of the pool. Moisten and tamp the sand to provide a solid base. The sand base must be 2 deep after tamping. The sand should be moistened and trowel to a smooth finish. Create a 6 radius cove along the wall as shown. This cove must also be tamped solid to prevent shifting. : through 10 are for overlap liners only. For beaded liners proceed to step 11. Step 7: Remove the liner from the carton and unfold into the pool. Be careful not to drag, abrade or snag the liner. Spread the liner out over the entire bottom of the pool. Raise the liner sidewall. Step 8: See Figure 8 and Detail 8. Place the liner over the edge of the wall. Make sure the overlap is equal around the outside of the pool wall. Cut the liner interlock into 2 pieces and center the pieces of the liner interlock over the wall at each upright. Place the bead receiver or wall channel over the wall edge as shown to secure the liner in place.. Step 8: See Detail 8C for a J-Bead Liner. Place the J Hook bead of the liner on top of the wall and push down firmly. Then place the bead receiver or wall channel over the J Bead liner and attach the top clips to the uprights. Do NOT put the J-Bead liner in the bead receiver. WRNING: Failure to use the sand or sand equivalent and shape it as specified will void all warranties on the pool and liner. FIGURE 3 W00007 CHNNEL SEVERL LYERS OF DUCT TPE 1/4-20 S.S. HEX NUT INSIDE OF 1/4-20 X 3/4 S.S. MCHINE SCREWS OUTSIDE OF INSIDE OF 1/4-20 S.S. HEX NUTS FIGURE 4 OUTSIDE OF ENCLOSURE BRS 1/4-20 X 3/4 S.S. MCHINE NOTE: Start wall enclosure strip at the bottom hole on the wall. If the enclosure strip does not cover the last hole at the top of the wall, you should attach with a ¼ 20 x ¾ machine FIGURE 5 L00036D 5

6 PN HED SCREWS SKIMMER THROT GSKET (VINYL) FOR LUMINUM S SKIMMER GSKET (CORK) UPRIGHT BOTTOM CLIP LOW PROFILE / FRONT CCESS SKIMMER #10 X ½ SELF TPPING SCREWS (4 PER UPRIGHT) FIGURE 6 W00025 NOTE: THE SKIMMER THROT GSKET MUST SNDWICH THE. I.E. ONE FLP OF THE GSKET MUST BE ON THE INSIDE OF THE ND THE OTHER ON THE OUTSIDE. SKIMMER THROT GSKET DETIL 6 W00030 PN HED SCREWS SKIMMER THROT GSKET (VINYL) FOR STEEL S SKIMMER GSKET (CORK) UPRIGHT BOTTOM CLIP LOW PROFILE/FRONT CCESS SKIMMER DIMENSIONS RE TO TOP OF #10 X ½ SELF TPPING SCREWS (6 PER UPRIGHT) CHNNEL 6 RDIUS FIGURE 7 W SND BSE

7 CHNNEL INTERLOCK BED RECEIVER NOTE: BOTTOM SHOULD BE CENTERED ON THE USING THE SEM T THE PERIMETER OF THE BOTTOM S GUIDE INTERLOCK SND BSE CHNNEL SND BSE DETIL 8 TO FLOOR SEM INTERLOCK OVERLP FIGURE 8 W00001 NOTE: If the liner is exposed to the sun for a long time, it will stretch and cause wrinkles. This can be avoided by waiting until dusk or by spraying cold water on the liner during installation. Step 9: Smooth all the wrinkles out on the bottom of the liner. To remove wrinkles, always pull the liner firmly but gently. No sharp tugs! Be certain liner is centered. Time spent removing wrinkles and aligning the liner will give you a neater looking and easily maintained pool. Step 10: See Figure 9 and 9B. For aluminum pools only, install captive nuts on top clips. If you have a steel pool attach the top clips as shown. Note, the support bracket is only used on 6 steel frames. Lift up one end of the bead receiver and slide the top clip onto it as shown in Figur e 9B. Slide the top clip completely onto the first bead receiver. Then push it down onto the wall. Next, slide the top clip over the adjacent bead receiver until the ends of the bead receiver is centered into the top clip FIGURE 8B & C BED RECEIVE INTERLOCK OVERLP DETIL 8B TOP CLIP W00023 BED RECEIVER J- BED DETIL 8C TOP CLIP #10 X ½ SELF TPPING SCREW BED RECEIVER CPTIVE NUT FOR LUMINUM S FOR STEEL S SUPPORT BRCKET (6 STEEL FRMES ONLY #10 X ½ SELF TPPING SCREW UPRIGHT FIGURE 9 FIGURE 9B 00005C 7

8 Steps 11 through 13 are for beaded liners only. For overlap liners proceed to step 14. BEDED S Step 11: See Figure 8B, Detail 8B and Figure 10. Place t he bead receiver on the wall. Tape the joints o f the bead receiver using fabric tape to protect the li ner. Place the top clips on the uprights. The support brackets (if provided) must be inserted into the round end uprights and rotated upward prior to installation of coping. ttach using one screw for the bracket and top clip and two additional screws for the top clip. Step 12: Remove the liner from the carton and unfold into the pool. Be careful not to drag, abrade or snag the liner. Spread the liner out over the entire bottom of the pool. Raise the liner side wall and place the bead into the bead receiver. Bead must be fully seated in the receiver to prevent it coming out later when being filled. Check it frequently while filling pool. Step 13: Smooth all the wrinkles out on the bottom of the liner. To remove wrinkles, always pull the line r firmly but gently. No sharp tugs! Be certain liner is centered. Time spent removing wrinkles and aligning the liner will give you a neater looking and easily maintained pool. DUCT TPE BED BED RECEIVER NOTE: If the liner is exposed to the sun for a long time, it will stretch and cause wrinkles. This can be avoided by waiting until dusk or by spraying cold water on the liner during installation. FIGURE 10 W00023 Step 14: Begin to fill the pool with water. Use a slow stream of water and fill approximately 1 1/2 deep. Make sure the fit of the liner is correct, smooth out any wrin kles in the pool bottom. If installing a deck, do not fill more than 12 until the deck is installed. Step 15: Fill the pool with 4 to 6 of water. Measur e the distance from the coping to the water surface a t several points around the pool to be certain that the pool is still level. WRNING: The pool must not be more than 3/4 out of level. If the pool is not level, drain the water and level the structure. ny non-compliance with this requirement will void all warranties. Step 16: See Figure 14. Locate the safety warning copings as described and as shown at the back of this manual. ttach coping as shown. To the outermost set of holes in the top clip. Step 17: t each upright, attach the coping and coping covers as shown in Figures 11, 12, 12B and 12C. Position the coping with warning labels as shown in Figure 14 and Figure 14B. Step 18: Fill the pool until the water level is 3 inches below the return hole. 8 Step 19: Follow the instructions for the filtration system, skimmer and return that are supplied with the filter. Step 20: ttach the remaining safety warning signs as described and shown in Figure 14 and B. I f

9 COPING COVER TTCHMENT FOR LUMINUM S COPING COVER #10-24 X 5/8 MCHINE SCREW LUMINUM S WITH LUMINUM COVERS #10 X ½ SELF TPPING SCREWS COPING BEND TBS TO SECURE TO COPING CHNNEL TOP CLIP (USE OUTERMOST SET OF HOLES) FIGURE 12 #10-24 X 5/8 MCHINE SCREW UPRIGHT PLUG FITS THIS WY ONLY! FIGURE 11 W00013D B PLUG LUMINUM S WITH RESIN COVERS #10-24 X 5/8 MCHINE SCREW #8 X 1 SELF TPPING SCREWS FIGURE 12B Face Plate #8 X 1 SELF TPPING SCREWS 9

10 FIGURE 12C COPING COVER TTCHMENT FOR STEEL S COPING COVER 6 FRME STEEL S WITH METL COVERS COPING COVER TIL SNP CP #10 X 1/2 SCREW PLUG #10 X 1 SCREW SNP CP WSHER COPING COVER BEND TBS UP UPRIGHT PLUG #10 X 1 SCREW STEEL S WITH RESIN COVER DO NOT USE POWER TOOLS 10

11 SKIMMER SSEMBLY TEFLON TPE PIPE TPE HOSE DPTER HOSE DPTER FCE PLTE GSKET FIBER WSHER LOCKNUT FIGURE 13 W00024 FCE PLTE FCE PLTE SCREW SNDWICH GSKET RUBBER GSKET FITTING RETURN SSEMBLY DIRECTIONL BLL (POINT OPENING WY FROM SKIMMER) DIRECTIONL BLL FITTING D C B FIGURE 14 WITH FRME LDDER ND FENCE WITH LDDER D C S00004 NOTE: Refer to Page 2., Warning section for Label Letter Designation DNGER: When a filter or any other electrical device is added to this pool, it is the responsibility of the purchaser to take all necessary precautions as set forth in article 680 of the National Electrical Code and local electrical codes. Failure to comply with th is requirement may result in a dangerous or hazardous electrical condition which may cause bodily injury or death. 11

12 installing a fence or deck refer to those manuals for proper placement of safety information. Step 21: Fill the pool up to the center of the skimmer, make sure that all fasteners are tightened properly and your pool is completely assembled. Please r ead The Sensible Way to Enjoy Your Pool booklet and enjoy years of swimming and relaxation. WTER SIDE DNGER B DECK SIDE POINT OF ENTRY B C & D DNGER C CUTION: D FIGURE 14B S00003B DDITIONL DNGER SIGN (SEE SIDE DECK MNUL) POINT OF ENTRY B C & D POINT OF ENTRY B C & D 12 WRNING: fter completion of the pool, the pool must never be drained to less than 1/2 full. Damage to the structure and/or liner may result.