BLUES CURING THE FUEL INJECTOR. In 1992, General Motors. BY JEFF MASTERMAN Armed with a pressure gauge, a good
|
|
- Daisy Stokes
- 7 years ago
- Views:
Transcription
1 CURING THE FUEL INJECTOR BLUES In 1992, General Motors introduced a very unique fuel injection system on its 4.3-liter Vortec V6 truck engine. Dubbed Central Port Injection, or CPI, the system looked and functioned much differently than previous designs. The CPI system utilizes one main injector that pressurizes six plastic tubes housed in the intake manifold. Each tube terminates in a spring-loaded poppet BY JEFF MASTERMAN Armed with a pressure gauge, a good scope and a working knowledge of its trouble spots, you can purge the demons that plague GM s CPI system. 20 July 2000
2 GM s 4.3-Liter Vortec V6 July
3 CURING THE FUEL INJECTOR BLUES The manifold tuning valve (MTV) can be removed from the top of the intake to allow visual inspection of the pressure regulator area without removing the plenum. If there s fuel laying in the intake or if the area around the regulator is very clean, the regulator diaphragm is probably leaking. Photos: Jeff Masterman being dumped directly into the crankcase or passenger-side cylinders. Fortunately, the manifold tuning valve (MTV) can be removed to allow easy inspection of the regulator if leakage is suspected. Fuel pressure leak-down with no external signs of leakage is another common problem on the CPI system. Like most injection systems, leak-down can result in long crank times or a stumble after restart. A quick way to isolate the cause of a leak-down problem on this system is to cycle the key and allow the fuel pump to run for a couple of seconds. Once the pump stops, simply pinch off the supply line. If the pressure holds, the cause is in the tank. If it doesn t, the intake will have to come off for a closer look at the internals. Inadequate fuel pressure or volume can also cause long crank times or a no-start condition. GM lists the pressure range for the valve that supplies fuel to its corresponding cylinder. The main injector is pulsed twice per crankshaft revolution, with pressurized fuel opening each poppet as system pressure approaches approximately 48 psi. The main injector and fuel pressure regulator on the CPI system are housed in a molded plastic piece with the six plastic tubes attached. GM dealers service this assembly as a single part number, and it s quite expensive to replace. The good news is that replacement pressure regulators, as well as fully reconditioned assemblies, are available via the aftermarket, which can save your customers substantial dollars on their repair bills. Common Problems Leaking pressure regulators are fairly common on the CPI system. Since the regulator is housed in the intake, a ruptured diaphragm often results in fuel Notice in this photo how the passenger side of the intake is much cleaner than the driver s side area. This is partially due to PCV flow, but can also be an indication of a leaking fuel pressure regulator (arrow). 22 July 2000
4 The EGR valve on the Vortec V6 sticks open frequently as a result of carbon buildup. While the intake is off, it s always a good idea to remove the valve and clean off as much carbon as possible to prevent rough idling. CPI system at 54 to 64. However, many techs have encountered hard-start or no-start complaints with pressure readings as high as 56 to 57 psi on a cold engine. This problem is amplified by the fact that many fuel pressure gauges have seen a rough life and can be off by as much as 2 to 5 psi. So always check the accuracy of your gauge before working on a CPI system. Finally, remember that the fuel pressure shouldn t drop during heavy acceleration. If it does, the volume of fuel being delivered needs to be evaluated. You ll find that many customers don t replace their fuel filter as a maintenance item, and it s not unusual to see a filter that s racked up 100,000 miles. Running for long periods against a restricted filter can kill even the best of fuel pumps. It can also cause big-time problems for the CPI system. Testing has shown that even slight changes in operating pressures can result in significant differences in the volume of fuel flowing through the poppet valves. EGR Woes EGR valves have been known to stick open on CPI engines due to carbon buildup. The result will be a rough idle, often accompanied by a failed emissions test due to high HC levels. These engines use an electronically controlled EGR valve with a built-in position sensor. Scan data can provide a quick check for this type of valve. With the key on and the engine off, just compare the EGR Desired percentage to EGR Actual. If the Actual percentage is higher than the Desired, the valve needs to be cleaned or replaced. The poppet valves on the CPI system have a tendency to stick open. If this occurs, a large amount of fuel will enter the combustion chamber. Fouled spark plugs can be a tip-off to this problem. If you look at the scan data, The intricate design of the CPI plenum can make it difficult to use propane during a cylinder balance test to determine if a misfire is due to a lean cylinder. July
5 CURING THE FUEL INJECTOR BLUES you ll find that the Long Term Fuel Trim number will be negative, as well. An improper spray pattern can cause one cylinder to run leaner than the rest, which could result in a rough idle and high HC during an idle emissions test. Performing a cylinder balance test can help you isolate the problem cylinder. Once the cylinder is identified, add propane at the throttle body until the rpm peaks. Then repeat the test. If the weak cylinder now contributes, the poppet valve for that cylinder should be suspect. One caveat: The intake design of the 4.3-liter Vortec V6 can prevent the propane from being evenly distributed among the cylinders. This can result in misleading test This ASNU machine used by Linder Technical Services can be used to both test and recondition CPI injector assemblies. It has an adjustable pressure function that s great for demonstrating the effect of fuel pressure changes on the volume of fuel delivered to the engine during cranking. Photo: Jim Linder Left: Here, the pressure of the ASNU machine is adjusted to around the middle of the specified range of the CPI system. The tester pulses the main injector a number of times using a programmed frequency. The result is 54 milliliters (ml) of fuel delivered at each poppet valve. Right: Now the pressure is reduced to 54 psi still within spec, but at the bottom of the range. Notice how the volume of fuel delivered drops to 42 ml. That s a 23% reduction in volume due to just a 6-psi drop in fuel pressure. This can create a no-start or extended cranking times on a cold engine. Photos: Jim Linder 24 July 2000
6 CURING THE FUEL INJECTOR BLUES Once the intake plenum is removed from the top of the engine, the spray pattern of a suspect poppet valve can be observed. Use caution during this type of test; excessive cranking can cause engine damage in a hurry. One look at this waveform tells you that the main injector on the CPI system is driven by the PCM using the peak-and-hold method. The pattern was captured by the scope connected to an external connector located behind the alternator. results. When in doubt, remove the intake plenum. An off-the-vehicle injector tester is by far the best choice for testing fuel flow on a CPI engine. If one is not available, there s an alternative test that can be performed after the plenum is removed. Begin the test by removing the coil wire from the distributor and securely ground it to prevent the engine from starting. Leave the ignition primary connected so the main injector will pulse. With the intake plenum off, the weak cylinder s plastic line can now be pulled out of the intake and the poppet valve placed in a container. Observe the spray pattern while an assistant cranks the engine briefly. Since the main injector is concealed by the intake, a noid light cannot be used for no-start diagnosis. However, there is a connector behind the alternator that can be used to check the power feed and the PCM-controlled ground side of the injector with your scope. While the scope is not connected at the injector, grabbing a waveform at this location tests the whole circuit. Note that GM uses a peak-and-hold driver arrangement on the CPI system, similar to its TBI setups. If the waveform indicates a problem, the intake will have to be removed to check the rest of the wiring. With a working knowledge of the system and an accurate fuel pressure gauge, you can win the diagnostic battle with GM CPI. Just remember what makes this system so different from the more common ones you see every day and you ll be on your way to having found a cure for the fuel injector blues. For a free copy of this article, write to: Fulfillment Dept., MOTOR Magazine, 5600 Crooks Rd., Troy, MI Additional copies are $2 each. Send check or money order. 26 July 2000
Oregon Fuel Injection
FORD POWERSTROKE DIAGNOSTICS 1994-2003 This guide is not a substitute for the proper diagnostic manuals and a scan tool. It is intended to be used with the proper tools to help diagnose and solve drivability
More informationEmission Control Systems Warranties
2004 Chevrolet TrailBlazer - 2WD Emission Control Systems Warranties This section outlines the emission warranties that General Motors provides for your vehicle in accordance with the U.S. Federal Clean
More informationModule 21 Fuel Injectors - Dual Point Injection (DPI)
Module 21 Fuel Injectors - Dual Point Injection (DPI) Author: Grant Swaim E-mail: sureseal@nr.infi.net URL: www.tech2tech.net Phone: (336) 632-9882 Fax: (336) 632-9688 Postal Address: Tech-2-Tech Website
More informationRobison On Rovers Carbon Fouling A New Kind of Valve Job
Robison On Rovers #2, February 20, 2000 By John Robison 1,750 words Robison On Rovers Carbon Fouling A New Kind of Valve Job Many of you have heard about the carbon fouling problem affecting newer Discoveries
More informationIntake Manifold: Service and Repair
2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 Copyright 2008, ALLDATA 9.90 Page 1 Intake Manifold: Service and Repair Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement.
More informationScan Tool Test Procedures Steve Zack - SPX. Scan Tool Test Procedures
Scan Tool Test Procedures Steve Zack - SPX Scan Tool Test Procedures Steve Zack - SPX 1 PCM Input Tests While performing many of these tests, to obtain the fastest possible Datastream refresh rate, please
More informationNISSAN FIGARO FAULT CODES AND DIAGNOSTICS
NISSAN FIGARO FAULT CODES AND DIAGNOSTICS The Nissan Figaro uses an engine management system with the acronym ECCS you ll see it in large letters on the plenum box when you open the bonnet. It stands for
More informationDiesel: Troubleshooting
Diesel: Troubleshooting Probable Cause Engine not starting Hard to start engine Runs rough at lower RPM Lack of power Diesel knock / pinking Black White Blue Low compression X X X Low fuel pressure X X
More informationBOSCH D-JETRONIC Volkswagen: Type 3 & 4
BOSCH D-JETRONIC Volkswagen: Type 3 & 4 MANIFOLD PRESSURE CONTROL SYSTEM (MPC) DESCRIPTION The Bosch D-Jetronic electronic fuel injection system is composed of 3 major subsystems: the air intake system,
More information53403500 - Injector Max Machine
53403500 - Injector Max Machine Operating Instructions Contents Page Introduction Operating Instructions Fuel Injection Cleaner - Petrol Operating Instructions Fuel Injection Cleaner - Diesel 3 Operating
More informationEmissions Readiness Monitor Strategies
Emissions Readiness Monitor Strategies A presentation by NYS DMV s Office of Clean Air for New York State Automobile Dealers Association 10/30/2012 1 What is the payoff for mastering readiness monitor
More informationSystem Diagnosis. Proper vehicle diagnosis requires a plan before you start
System Diagnosis Proper vehicle diagnosis requires a plan before you start Following a set procedure to base your troubleshooting on will help you find the root cause of a problem and prevent unnecessary
More informationE - THEORY/OPERATION
E - THEORY/OPERATION 1995 Volvo 850 1995 ENGINE PERFORMANCE Volvo - Theory & Operation 850 INTRODUCTION This article covers basic description and operation of engine performance-related systems and components.
More informationTurbocharger system components, servicing
21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners
More informationEvaporative emissions system
just a test. Evaporative emissions system 20-48 Function description of EVAP canister system Depending upon the air pressure and ambient temperature, fuel vapor will form above the level of fuel in the
More informationQuestions and Answers
Emissions Warranties for 1995 and Newer Light-duty Cars and Trucks under 8,500 Pounds Gross Vehicle Weight Rating (GVWR) Federally required emission control warranties protect you, the vehicle owner, from
More informationThrottle Body Fuel Injection
Throttle Body Fuel Injection Initial Calibration of the TBI Disclaimer The author of this presentation assumes NO responsibility for information provided causing the owner to modify or alter their motorhome
More informationTechnician High Pressure Pump Guide for the 7.3 Power Stroke Engine
Technician High Pressure Pump Guide for the 7.3 Power Stroke Engine HIGH PRESSURE PUMP. PUMP LEAKS. ICP SYSTEM DIAGNOSTICS. REPAIR PARTS. TOOLS IPR TEST TOOLS AND ICP PUMP LEAK REPAIR High pressure pumps
More informationThis bulletin is intended to aid technicians in the correct procedure of performing diagnostics on a Power Stroke 6.0L.
Technical Bulletin November 2010 Power Stroke 6.0L Diagnostics Submitted by: Tony Salas This bulletin is intended to aid technicians in the correct procedure of performing diagnostics on a Power Stroke
More informationAustin High School Automotive Service Technology Engine Repair 9 th grade Course Syllabus
Austin High School Automotive Service Technology Engine Repair 9 th grade Course Syllabus 1 Prerequisites: Students entering the Automotive Technology Program for engine repair must be of the ninth grade
More informationUnit 8. Conversion Systems
Unit 8. Conversion Systems Objectives: After completing this unit the students should be able to: 1. Describe the Basic conversion systems 2. Describe main conversion kit types. 3. Describe how the CNG
More informationQuik Lining Systems Heater Owners Guide
Quik Lining Systems Heater Owners Guide Quik Lining Systems, Inc is pleased to present the Quik Heater, an innovative heater used to cure cured in place pipe for sewer laterals. The unit is the most cost
More informationFUEL-16, Troubleshooting Fuel Supply Problems
FUEL-16, Troubleshooting Fuel Supply Problems Introduction This procedure is used to troubleshooting fuel supply problems including failure of the fuel pump to start during engine cranking. Fuel Pump Not
More informationDIAGNOSING FORD MISFIRES
A2003 Ford F-150 V8 rolls into your shop, with the customer complaint that the vehicle runs rough at times. This occurs mostly under light-to-moderate acceleration and the Check Engine light is not illuminated.
More informationVAG 1687 Diagnostic Tool, Checking Intake System for Leaks. Condition. Service 00-A354 00-A353
Subject: Model(s): VAG 1687 Diagnostic Tool, Checking Intake System for Leaks All with 1.8L Turbo All with 2.7L BiTurbo 1997 2000 Group: Number: Date: 01 01 01 Oct. 26, 2001 Condition VAG 1687 Diagnostic
More informationDescribe the procedure used to check for spark. Discuss what to inspect and look for during a visual inspection of the ignition system.
CHAPTER 20 OBJECTIVES Describe the procedure used to check for spark. Discuss what to inspect and look for during a visual inspection of the ignition system. List the steps necessary to check and/or adjust
More informationAutomotive Sensor Simulator. Automotive sensor simulator. Operating manual. AutoSim
Automotive sensor simulator Operating manual AutoSim Contents Introduction.. page 3 Technical specifications.... page 4 Typical application of AutoSim simulator..... page 4 Device appearance... page 5
More informationDiesel Fuel Systems. Injection Nozzles
Diesel Fuel Systems Injection Nozzles Unit Terms Injection nozzle Nozzle, nozzle holder, valve, spring assembly Nozzle assembly Valve, body, and spray valve Orifice Small hole Pintle Valve which the end
More informationPiston Diagnosis A rough Guide
Piston Diagnosis A rough Guide The process of examining used pistons can tell us a lot of helpful information on the condition of an engine. When engine failure does occur the piston is likely to take
More informationDiagnosing Hydraulic Problems
Diagnosing Hydraulic Problems 1 Problems A pressure test is a key check when you need to determine if a problem is caused by something that is inside or outside of the transmission. Low automatic transmission
More informationUnited States Air and Radiation EPA420-F-95-014 Environmental Protection December 1995 Agency
United States Air and Radiation EPA420-F-95-014 Environmental Protection December 1995 Agency Office of Mobile Sources --------------------------------------------------------------------- EPA Environmental
More informationLAND ROVER FUEL INJECTION SYSTEMS
LAND ROVER FUEL INJECTION SYSTEMS INTRODUCTION Land Rover vehicles use one of two types of electronically controlled fuel injection systems: Multiport Fuel Injection (MFI) or Sequential Multiport Fuel
More informationCarburetion Troubleshooting Quick Reference Guide
Carburetion Troubleshooting Quick Reference Guide SERVICE DIAGNOSTIC OVERVIEW A logical, planned approach can move service work through a repair center in a smooth and efficient manner. Fueled by information
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING. NOT LEGAL FOR SALE OR USE IN CALIFORNIA OR ON ANY POLLUTION CONTROLLED VEHICLES.
Twin Tec Installation Instructions for Twin Cam Ignition CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING. T LEGAL FOR SALE OR USE IN CALIFORNIA OR ON ANY POLLUTION CONTROLLED VEHICLES. OVERVIEW
More informationThe On-Board Refueling Vapor Recovery (ORVR) Evaporative Emission (EVAP) system.
«1A: Description and Operation» Overview The Evaporative Emission (EVAP) system prevents fuel vapor build-up in the sealed fuel tank. Fuel vapors trapped in the sealed tank are vented through the vapor
More informationQUICK TUNE EFI INSTRUCTION MANUAL
QUICK TUNE EFI INSTRUCTION MANUAL Step 1: Loading the CB quick Tune Software to your PC A) Take the CB Quick Tune installation CD and load it into your PC. A window will pop up asking to have all programs
More informationTechnical Service Information
Technical Service Information COMPLAINT: CAUSE: 1996-20 DEFINITIONS When a VW/Audi vehicle is exhibiting a symptom or is in fail-safe, the technician, in many cases, is unable to communicate with the on-board
More informationNISSAN FIGARO - STARTING PROBLEMS
NISSAN FIGARO - STARTING PROBLEMS Just to clarify starting problems in this context assumes that the engine turns over on the starter it simply won t fire-up. If the issue is failure of the engine to turn-over
More informationON-Board Diagnostic Trouble Codes
ON-Board Diagnostic Trouble Codes The list below contains standard diagnostic trouble codes (DTC s) that are used by some manufacturers to identify vehicle problems. The codes provide below are generic
More information2003-2004: Service Information: Fuel Tank System
2003-2004: Service Information: Fuel Tank System Corvette and Cadillac XLR Partway through model year 2003, a new fuel tank system was introduced on the Corvette (fig. 1). This system continues with slight
More informationSystem Saver 318 Air Compressor for Mack E-Tech and ASET Engines
Maintenance Manual 31 System Saver 318 Air Compressor for Mack E-Tech and ASET Engines Revised 08-05 NON-THROUGH DRIVE THROUGH DRIVE Service Notes About This Manual This manual provides service and repair
More informationEngine. 204-1890 Strobe light, 110V 204-1891 Strobe light, 220V 204-458 Replacement bulb. 204-1057 Compression gauge. 204-166 Dial indicator
The Strobe light checks the unit for: Balance of operating machinery RPM of motors, engine pulleys, fans, etc. Observe belt slippage Strobe light will stop action at speeds from 200 to 6000 RPM 204-1890
More informationThe fastest and easiest way to troubleshoot Marine Electronic Fuel Injection Systems USER S GUIDE Version 5
MerCruiser SCAN TOOL The fastest and easiest way to troubleshoot Marine Electronic Fuel Injection Systems USER S GUIDE Version 5 Rinda Technologies, Inc. MerCruiser SCAN TOOL USER S GUIDE Rinda Technologies
More informationDTC P0401, DTC P1491,
Service Bulletin 05-026 Applies To: 1999 02 Odyssey ALL 2003 Odyssey From VIN 2HKRL18..3H500001 thru 2HKRL18..3H504511 and from VIN 5FNRL18..3B000001 thru 5FNRL18..3B067057 2003 Pilot From VIN 2HKYF18..3H500001
More informationENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER...
FUEL FILTER............................ FUEL HEATER.......................... INJECTOR.............................. SUPPLY PUMP.......................... COMMON RAIL.......................... FUEL PRESSURE
More informationEVAP LEAK DTC DIAGNOSIS
Classification: Reference: Date: EC09-001a NTB09-020a March 5, 2010 EVAP LEAK DTC DIAGNOSIS This bulletin has been amended. The REPAIR FLOW CHART has been amended. CLAIMS INFORMATION has been added. Please
More informationDiagnostic Trouble Code (DTC) Charts
Diagnostic Trouble Code (DTC) Charts Note: Before proceeding to the Pinpoint Test, refer to the Diagnostic Trouble Code (DTC) Descriptions for additional information to assist in diagnosis. 6.0L Diesel
More informationTOYOTA ELECTRONIC TRANSMISSION CHECKS & DIAGNOSIS
Checks and Adjustments The transmission requires regular maintenance intervals if it is to continue to operate without failure. As we discussed in previous sections, transmission fluid loses certain properties
More informationLPEFI Liquid Propane Electronic Fuel Injection General Diagnostic Manual
LPEFI Liquid Propane Electronic Fuel Injection General Diagnostic Manual Revision 10 February, 2014 Manual # M4-121-10 Bi-Phase Technologies, LLC Eagan, Minnesota, U.S.A. This manual is for general diagnosis
More informationWynn s Extended Care
Wynn s Extended Care Every car deserves to receive the very best care... especially yours. How Do You Keep Your Reliable Transportation Reliable? Count on Wynn s Because Wynn s has been caring for cars
More informationPowertrain DTC Summaries EOBD
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar XJ Range V6, V8 N/A and V8 SC 2003.5 Model Year Refer to pages 2 9 for important information regarding the use of Powertrain DTC Summaries.
More informationElectric Brake Trouble Shooting Guide
Electric Brake Trouble Shooting Guide PROBLEM CAUSES REMEDIES S OPEN CIRCUITS SEVERE SHORT CIRCUITS FIND AND S FIND AND WEAK S GREASE/OIL ON MAGNETS/LININGS CORRODED CONNECTIONS WORN LININGS OR MAGNETS
More informationDTC P1271/78 FUEL PRESSURE REGULATOR CIRCUIT MALFUNCTION (OPEN/SHORT) DTC P1272/78 FUEL PRESSURE REGULATOR SYSTEM MALFUNCTION
05 596 DIAGNOSTICS ECD SYSTEM (1KD FTV)(From August, 2004) DTC P1271/78 FUEL PRESSURE REGULATOR CIRCUIT MALFUNCTION (OPEN/SHORT) 05NJ6 01 DTC P1272/78 FUEL PRESSURE REGULATOR SYSTEM MALFUNCTION For more
More informationCylinder Leak- Down Tester
Cylinder Leak- Down Tester Item 94190 INSTRUCTIONS AND PRECAUTIONS Visit our website at: http://www.harborfreight.com When unpacking, make sure that the product is intact and undamaged. If any parts are
More informationModule 6 Engine Control Module (ECM)
Module 6 Engine Control Module (ECM) Author: Grant Swaim E-mail: sureseal@nr.infi.net URL: www.tech2tech.net Phone: (336) 632-9882 Fax: (336) 632-9688 Postal Address: Tech-2-Tech Website PO Box 18443 Greensboro,
More informationDESCRIPTION. DTC P0351 Ignition Coil "A" Primary / Secondary Circuit. DTC P0352 Ignition Coil "B" Primary / Secondary Circuit
1 of 10 6/4/2012 10:38 PM Last Modified: 3-27-2012 6.4 C From: 201203 Model Year: 2013 Model: FR-S Doc ID: RM000000XH40PUX Title: FA20 ENGINE CONTROL: SFI SYSTEM: P0351-P0354: Ignition Coil "A" Primary
More informationApprenticeship Training Standard. Automotive Service Technician. Trade Code: 310S
Apprenticeship Training Standard Automotive Service Technician Trade Code: 310S Development Date: January 2003 Please Note: Apprenticeship Training and Curriculum Standards were developed by the Ministry
More informationTrouble Shooting. Pump
Trouble Shooting Pump Trouble Possible Cause Remedy Oil leaking in the area of water pump crankshaft Worn crankshaft seal, bad bearing, grooved shaft, or failure of retainer o-ring. Excessive play on crankshaft
More informationPERFORMANCE SYSTEMS INTEGRATION
2006 Current GEN IV LSX/Vortec 4.8, 5.3, 6.0, 6.2, 7.0 Drive by Wire (58X) Electronic Fuel Injection Wiring Harness w/4l60e or 4L80E Automatic Transmission HAR-10 (See Below) (P/N HAR- 1036, 1038, 1040,
More informationCDS TROUBLESHOOTING SECTION I. VACUUM. 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg)
CDS TROUBLESHOOTING SECTION I. VACUUM 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg) 1.1. Clogged hoses or wand tube. Disconnect hoses and carefully check for an obstruction. 1.2. Excessive
More informationWARRANTY. Overview. Important Information You Should Know
Overview It s important that Sales Consultants explain all applicable warranties to his/her customers. A thorough explanation of all applicable warranty coverage at the time of sale helps provide the owner
More informationRexroth Hydraulic Pump A10VO Series User Manual
Rexroth Hydraulic Pump A10VO Series User Manual Rexroth Hydraulic pump A10VO Series User Manual Revised 5/1/2009 Page 1 of 12 Functional Purpose This pump is preferred over a fixed displacement (gear)
More informationActuator-Swirl Valve DESCRIPTION
US/Canadian 2007 Sprinter Diesel V6 Dodge Service Manual Swirl Valve Info Actuator-Swirl Valve DESCRIPTION The swirl valve linkage links the swirl valves in the intake manifold to the swirl valve actuator.
More informationSALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT
SALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT INSTALLATION MANUAL: 2005 MUSTANG 4.6 3V MANUAL P/N: 10-8002-C14338C SUPERCHARGER KIT P/N: 10-1607-B14083* Saleen Performance, Inc. 1225 East Maple Rd.,
More informationMarine Piston Damage By Tom Benton, Marine Surveyor
Marine Piston Damage By Tom Benton, Marine Surveyor In the last several years I have noticed an increase in the number of outboard motors which have sustained piston damage, and several cases in V-8 inboard
More informationFUEL SYSTEM 3.1L DIESEL ENGINE
WJ FUEL SYSTEM 3.1L DIESEL ENGINE 14-1 FUEL SYSTEM 3.1L DIESEL ENGINE TABLE OF CONTENTS page GENERAL INFORMATION... 1 FUEL DELIVERY SYSTEM 3.1L DIESEL ENGINE... 2 page FUEL INJECTION SYSTEM 3.1L DIESEL
More informationEngine, Drive Train, and Hydraulic Repair Indicator Quick Reference Guide
Engine, Drive Train, and Hydraulic Repair Indicator Quick Reference Guide Planned Indicators Planned Indicators SM provide the best insight Service Meter Hours CAT Engine Repair Indicators Description
More information1955-1956 Chevy Bel-Era
Classic Instruments 1955-1956 Chevy Bel-Era Installation Manual Revised January 2, 2014 Page 1 Table of Contents Table of Contents 2 Welcome to the Team of Classic Instruments! 3 55-56 Chevy Part Identification
More informationSAS light Check Engine Malfunction Indicator Lamp
SAS light Check Engine Malfunction Indicator Lamp Here's how to do it: In car ECM Diagnostics/ECM Reset procedure: 1) Sit in the driver's seat. 2) Turn the ignition key to the ON position and wait three
More informationAppendix S TRANSPORTATION, DISTRIBUTION AND LOGISTICS YOUTH APPRENTICESHIP AUTO TECHNICIAN PATHWAY ENGINE PERFORMANCE & REPAIR (UNIT 11)
Appendix S TRANSPORTATION, DISTRIBUTION AND LOGISTICS YOUTH APPRENTICESHIP AUTO TECHNICIAN PATHWAY ENGINE PERFORMANCE & REPAIR (UNIT 11) Auto Technician Pathway: (Unit 11) PAGE 1 OF 27 1. Assist to diagnose
More informationCummins Westport, Inc. Engine Overview. March 2015
Cummins Westport, Inc. Engine Overview March 2015 Cummins Westport Inc. (CWI) A Cummins JV Company CWI was established in 2001 as a 50/50 joint venture company between Cummins Inc and Westport Innovations.
More informationCat Electronic Technician 2015C v1.0 Product Status Report 2/20/2016 4:34 PM
Cat Electronic Technician 2015C v1.0 Product Status Report 2/20/2016 4:34 PM Product Status Report Parameter Product ID Equipment ID Comments Value JGB00714 NOT PROGRAMMED Machine Control 345D (JGB00714)
More informationwww.servicechamp.com
1-800-221-0216 Fax: 1-800-472-2281 www.servicechamp.com Service Champ Part 52081 Service Interval every 30,000 miles / Chevrolet 1992-2002 6.5 liter Description and Operation The fuel filter element separates
More informationVehicle Engine Management Systems
Unit 11: Vehicle Engine Management Systems NQF level 3: Guided learning hours: 60 BTEC National Unit abstract Modern motor vehicles continue to make use of the rapid advances in electronics technology
More informationDIAGNOSIS SYSTEM (3S GTE and 5S FE)
Diagnosis System (3SGTE and 5SFE) FI39 DIAGNOSIS SYSTEM (3SGTE and 5SFE) DESCRIPTION The ECM contains a builtin, selfdiagnosis system by which troubles with the engine signal network are detected and a
More informationCat Electronic Technician 2015A v1.0 Product Status Report 4/20/2016 2:49 PM
Page 1 of 19 Cat Electronic Technician 2015A v1.0 Product Status Report 2:49 PM Product Status Report Parameter Value Product ID WRK00337 Equipment ID WRK00337 Comments A01-52 C9 330D (THX37891) Parameter
More informationElectronic Diesel Control EDC 16
Service. Self-Study Programme 304 Electronic Diesel Control EDC 16 Design and Function The new EDC 16 engine management system from Bosch has its debut in the V10-TDI- and R5-TDI-engines. Increasing demands
More informationPollution by 2-Stroke Engines
Pollution by 2-Stroke Engines By Engr. Aminu Jalal National Automotive Council At The Nigerian Conference on Clean Air, Clean Fuels and Vehicles, Abuja, 2-3 May 2006 Introduction to the 2-Stroke Engine
More informationWaters Corporation. Waters 2690/5 USER & TROUBLESHOOTING GUIDE
Waters Corporation Waters 2690/5 USER & TROUBLESHOOTING GUIDE Contents 2690/5 Theory Setup procedures. Troubleshooting the 2690/5 User maintenance of the 2690/5 Spare Parts 2 2690/5 Theory 2690/5 Solvent
More information5.0L SEFI EEC IV TESTING
5.0L SEFI EEC IV TESTING 1987 Lincoln Mark VII 1987 Computerized Engine Controls FORD MOTOR CO. EEC IV DIAGNOSIS & TESTING 5.0L SEFI DIAGNOSIS & TESTING DIAGNOSTIC PROCEDURE This diagnostic procedure is
More informationENTRY-LEVEL AUTOMOTIVE TECHNICIAN
ENTRY-LEVEL AUTOMOTIVE TECHNICIAN Definition: An entry-level automotive technician performs diagnosis and repair to gasoline powered cars and light trucks with limited supervision. The last two bands of
More informationTechnical Guide 08/15/14
Technical Guide 08/15/14 1 Table of Contents Contact information.3 Identifying your system..4-8 Model Number Serial number location Parts of your fuel system..9-14 Fuel pump diagram Wire harness schematics
More informationECUs and Engine Calibration 201
ECUs and Engine Calibration 201 Jeff Krummen Performance Electronics, Ltd. www.pe-ltd.com Page 1 Before we get started.. ECUs and Engine Calibration 201 The goal of this presentation is to explain the
More informationPowertrain DTC (P000-P0999) for EOBD Vehicles (Directive 98/69/EC of the European Parliament)
Powertrain DTC (P000-P0999) for EOBD Vehicles (Directive 98/69/EC of the European Parliament) 1 Trouble Fault location Probable cause code 1 P0000 No fault found - P0001 Fuel volume regulator control -
More informationEngine Diagnostic and Drivability Training
Engine Diagnostic and Drivability Training 1 Preface Preface This Participant s Manual is designed to support the training course for applicable vehicles and vehicle systems. Refer to service information
More informationWhat Is a Typical CNG Vehicle?
The Maintenance of CNG Vehicles What Is a Typical CNG Vehicle? CNG Vehicles They Come In All Shapes and Sizes CNG is a Proven Technology Sedans, Pick-ups, Vans/Wagons Honda All GMC brands Ford/Mercury/Lincoln
More informationREMOVAL AND INSTALLATION
303-01C-1 REMOVAL AND INSTALLATION Engine Body On Special Tool(s) Adapter For 303-D043 303-D043-02 or equivalent Special Tool(s) 303-01C-1 Turbocharger Lifting Bracket 303-1266 Wrench, Fan Clutch Nut 303-214
More informationDTC P0351 Ignition Coil "A" Primary / Secondary Circuit. DTC P0352 Ignition Coil "B" Primary / Secondary Circuit
208 2UZ-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P05 Ignition Coil "A" Primary / Secondary Circuit DTC P052 Ignition Coil "B" Primary / Secondary Circuit DTC P05 Ignition Coil "C" Primary / Secondary Circuit
More informationDTC P0125 Insufficient Coolant Temperature for Closed Loop Fuel Control
EINE (5VZFE) DI195 DI8YY02 DTC P0125 Insufficient Coolant Temperature for Closed Loop Fuel Control CIRCUIT DESCRIPTION To obtain a high purification rate of the CO, HC and x components of the exhaust gas,
More informationTechnician Turbocharger Guide for the 6.0L Power Stroke Engine
Technician Turbocharger Guide for the 6.0L Power Stroke Engine Vanes VGT Actuator Piston Turbine Wheel Shaft Seal Compressor Wheel VGT Control Valve TURBOCHARGER DESCRIPTION AND BASIC OPERATION The turbocharger
More informationCNC Ported Big Valve Cylinder Heads. Performance Intake Manifold. Forged Pistons (Engine set with rings, pins and clips)
Performance Engine Assemblies 20001721 2.0lt Performance Crate Engine 205BHP 20001722 2.0lt Performance Crate Engine 225BHP 20001723 2.0lt Performance Crate Engine 255BHP 20001725 2.3lt Performance Crate
More informationIncreasing Reliability and Availability for Automotive Embedded Devices by Enhanced Wiring Diagnosis
Increasing Reliability and Availability for Automotive Embedded Devices by Enhanced Wiring Diagnosis Overview Introduction Potential situations and their detection Deficits of previously eisting concepts
More informationService. Engine. Engine Model: General Motors 4.3 L Powertrain. Generator Models: 30--45 kw TP-6103 1/01
Service Engine Engine Model: General Motors 4.3 L Powertrain Generator Models: 30--45 kw TP-6103 1/01 CAUTION Caution: In order to reduce the chance of personal injury and/or property damage, carefully
More information6.7L Diesel Fuel System Contamination Diagnosis and Service Procedure Job Aid (Revised March, 2012)
6.7L Diesel Fuel System Contamination Diagnosis and Service Procedure Job Aid (Revised March, 2012) Fuel contamination on 6.7L diesel engines can damage fuel system components including the High Pressure
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationVia Raffaello,33/A - 42100 Reggio Emilia Italia Tel +39 0522.514.461 Fax +39 0522 514469 - E-mail: aftersales@landi-gas.
Trouble Shooting Solving problems with LSI-NSI software Update to version 2.1.0 1/14 Rev.0 2/14 Rev.0 CONTENTS 1.1. Switching from petrol to gas PAGE 4 1.2. Drop at medium-high speeds PAGE 5 1.3. Functioning
More informationTEST INFORMATION ADVANCED ENGINE PERFORMANCE SPECIALIST TEST (L1)
REVISED 2016 With Composite Vehicle Type 4 TEST INFORMATION FOR THE ADVANCED ENGINE PERFORMANCE SPECIALIST TEST (L1) OVERVIEW TEST SPECIFICATIONS TASK LIST GLOSSARY OF TERMS SAMPLE QUESTIONS INDUSTRY TRAINING
More informationDTC Database (OBD-II Trouble Codes)
Auto Consulting S.a.s di Cofano A. & C. Attrezzature diagnostiche Elaborazioni elettroniche Formazione tecnica DTC Database (OBD-II Trouble Codes) Definitions for generic powertrain diagnostic trouble
More informationFault codes DM1. Industrial engines DC09, DC13, DC16. Marine engines DI09, DI13, DI16 INSTALLATION MANUAL. 03:10 Issue 5.0 en-gb 1
Fault codes DM1 Industrial engines DC09, DC13, DC16 Marine engines DI09, DI13, DI16 03:10 Issue 5.0 en-gb 1 DM1...3 Abbreviations...3 Fault type identifier...3...4 03:10 Issue 5.0 en-gb 2 DM1 DM1 Fault
More informationDiagnostic Fault Codes For Cummins Engines
Section - Diagnostic Fault Codes For Cummins Engines Applies to Engine Models T, T, QSL T, QSM, QS, QSK9, QSK, QST, QSK//8 Note: These fault codes are current at date of publication. Always refer to engine
More information