R&S FS-K130PC Distortion Analysis Software Specifications

Transcription

1 FS-K130PC_dat-sw_en_ _cover.indd 1 Data Sheet Test & Measurement R&S FS-K130PC Distortion Analysis Software Specifications :46:15

2 CONTENTS Specifications... 3 Recommended system configuration... 3 Distortion Analysis software... 3 Frequency... 3 Level... 3 Bandwidth... 4 Reference signal (Input/ref signal)... 4 Measurement signal (Output/meas signal)... 4 Measurement configuration... 5 Signal processing parameters... 5 Graphical result display... 5 Numerical results... 6 Ordering information... 7 The specifications of the R&S FS-K130PC Distortion analysis software are based on the data sheet specifications of the R&S FSQ/ R&S FSU/R&S FSG/R&S FSV/R&S FSVR/R&S FSUP/R&S FSW signal and spectrum analyzer, have not been checked separately and are not verified during instrument calibration. Measurement uncertainties are given as 95 % confidence intervals. The specified level measurement errors do not take into account systematic errors due to reduced signal to noise ratio (S/N). Specifications apply under the following conditions: 30 minutes warm-up time at ambient temperature, specified environmental conditions met, calibration cycle adhered to, and all internal automatic adjustments performed. Typical values are designated with the abbreviation (typ.). These values are verified during the final test but are not assured by Rohde & Schwarz. Nominal values are design parameters that are not assured by Rohde & Schwarz. These values are verified during product development but are not specifically tested during production. Data without tolerance limits is not binding. 2 Rohde & Schwarz R&S FS-K130PC Distortion Analysis Software

3 Specifications Recommended system configuration Operating system Windows 7 (32-bit or 64-bit) Free hard disk space 1 Gbyte Free RAM 2 Gbyte Graphics resolution UXGA ( pixel) USB 1 free USB port for connecting the smartcard reader (if no PC-built-in smartcard reader is used) License Dongle R&S FSPC (order no ) Measuring instrument connection Hardware: IEC/IEEE bus or LAN connection Software: VISA driver National Instruments VISA Version 5.2 or Agilent IO Libraries Suite 16.2 or later Distortion Analysis software The R&S FS-K130PC distortion analysis software is compatible with R&S FSW signal and spectrum analyzer, R&S FSQ signal analyzer, R&S FSG spectrum analyzer, R&S FSU spectrum analyzer with option R&S FSU-B73, R&S FSV signal and spectrum analyzer, R&S FSVR real-time spectrum analyzer, R&S FSUP signal source analyzer R&S SMU200A, R&S SMJ100A, R&S SMATE200A, R&S SMBV100A, R&S SMW200A vector signal generators. Frequency Frequency range measurement RF input according to the frequency range of the used analyzer and generator as stated in the data sheet Level Level range measurement RF input 50 dbm to +30 dbm 1 Level setting auto 1 1 Restricted IF overload and auto level functionality depending on carrier frequency and bandwidth at carrier frequencies < 50 MHz. Rohde & Schwarz R&S FS-K130PC Distortion Analysis Software 3

4 Bandwidth Sample rate RF input R&S FSW: up to 200 MHz R&S FSQ: 400 Hz to 81.6 MHz R&S FSG: up to 81.6 MHz R&S FSU: up to 81.6 MHz (R&S FSU-B73) R&S FSUP: up to 81.6 MHz R&S FSV: 100 Hz to 45 MHz R&S FSVR: up to 128 MHz with I/Q bandwidth extension R&S FSW: up to 1.2 GHz (R&S FSW-B500) R&S FSQ: up to MHz (R&S FSQ-B72) R&S FSV: up to 400 MHz (R&S FSV-B160) Maximum acquisition bandwidth (equalized) Reference signal (input/ref signal) RF input with I/Q bandwidth extension R&S FSW: 10 MHz R&S FSQ: 28 MHz R&S FSG: 28 MHz R&S FSU: 7 MHz (R&S FSU-B73) R&S FSUP: 7 MHz R&S FSV: 28 MHz R&S FSVR: 40 MHz R&S FSW: 500 MHz (nom.) (R&S FSW-B500) R&S FSQ: 120 MHz (R&S FSQ-B72) R&S FSV: 160 MHz (R&S FSV-B160) Supported numerical signal sources built-in signal types band-limited noise, dual tone, digital modulated band-limited noise selectable bandwidth selectable notch bandwidth crest factor optimization selectable dual tone selectable tone spacing digital modulated selectable modulation type selectable symbol count and oversampling selectable filter type file based file format binary, ASCII, Matlab, IQW, IBN or WV running on ARB any R&S SMx ARB-based standard Reference signal clock rate selectable Reference signal length to samples 2 Reference signal level depending on signal generator Marker control restart marker marker 1/marker 2/marker 3/marker 4 marker timing offset selectable within signal length Signal settling delay 100 ms to 5 s Measurement signal (output/meas signal) Supported measurement signal sources measurement hardware all supported analyzer types file based file format binary, ASCII, Matlab, IQW, IBN or WV simulation (built-in) various simulation modes and parameters Result length to samples Averaging I/Q based averaging 1 to Trigger modes free run, external 2 Tested with 1 Msample reference signal length on a PC with 2 Gbyte memory. 3 Tested with 1 Msample measurement signal; depending on the reference signal length, the averaging factor may be reduced. 4 Rohde & Schwarz R&S FS-K130PC Distortion Analysis Software

5 Measurement configuration DUT port type input port RF output port RF DUT measurement parameters frequency RF frequency multiplier, divider, frequency offset level output RMS level maximum input peak and RMS level post-measurement level can be attenuated or set to RF off DUT input and output attenuation pads fixed attenuation 30 db to 80 db Reference frequency coupling 10 MHz reference frequency source any controlled instrument external reference frequency generator no coupling Signal processing parameters Signal synchronization sync mode none timing, phase and gain full synchronization measurement periods to analyze all/limited to n periods error compensation (individual switchable on or off) I/Q imbalance, I/Q offset, frequency error, timing offset, amplitude droop Generic parameter calculation nonlinear estimation order 5 to 15 Channel estimation active yes or no impulse response taps 64 to 4096 impulse response overlap 5 to 100 % System identification polynomial estimation modes complex, AM and PM polynom estimation degrees full/odd/even fit order min/max degree 1 to 15 System identification spline spline segments 4 to 20 steps per spline 2 to 10 System identification memory polynomial polynomial degree 0 to 15 tap count 0 to 9 System identification volterra Volterra structure configurable up to 9 th order Digital predistortion (DPD) yes/no Graphical result display Results 4 capture buffer ref, meas without and with DPD power (synchronized capture buffer) ref, meas, modeled, ref - meas, modeling error, DPD, expected after DPD, meas after DPD gain gain vs. ref, gain vs. meas, gain vs. ref modeled, EVM vs. ref. gain vs. meas after DPD expected, gain vs. meas after DPD measured constellation ref, meas, modeled, ref meas, DPD, meas after DPD expected and measured AM/AM (amplitude compression) meas, modeled, DPD, meas after DPD expected and measured, reference lines AM/φM (phase compression) meas, modeled, DPD, meas after DPD expected and measured, reference lines I and Q ref I, ref Q, meas I, meas Q, modeled I, modeled Q EVM meas ref, meas model, ref after DPD expected, ref after DPD measured Channel amplitude, phase Rohde & Schwarz R&S FS-K130PC Distortion Analysis Software 5

6 Numerical results Results 4 power measurement DUT input RMS, peak, crest DUT output RMS, peak, crest DUT output leveling error signal synchronization averages executed, confidence frequency offset, phase offset, trigger offset I/Q offset, gain imbalance, quadrature error, I/Q imbalance intercepts gain, compression, 1dB compression point fundamentals, 3 rd and 5 th order product, IP3, IP5 modulation quality EMV RMS, EVM peak system modeling modeling error 4 Depending on the signal processing configuration, some results may not be available. 6 Rohde & Schwarz R&S FS-K130PC Distortion Analysis Software

7 Ordering information Designation Type Order No. Distortion Analysis Software R&S FS-K130PC License Dongle R&S FSPC Signal and Spectrum Analyzer, 2 Hz to 8 GHz R&S FSW Signal and Spectrum Analyzer, 2 Hz to 13.6 GHz R&S FSW Signal and Spectrum Analyzer, 2 Hz to 26.5 GHz R&S FSW Signal and Spectrum Analyzer, 2 Hz to 43.5 GHz R&S FSW Signal and Spectrum Analyzer, 2 Hz to 50 GHz R&S FSW Signal and Spectrum Analyzer, 2 Hz to 67 GHz R&S FSW Signal Analyzer, 20 Hz to 3.6 GHz R&S FSQ Signal Analyzer, 20 Hz to 8 GHz R&S FSQ Signal Analyzer, 20 Hz to 26.5 GHz R&S FSQ Signal Analyzer, 20 Hz to 40 GHz R&S FSQ Signal Analyzer, 9 khz to 8 GHz R&S FSG Signal Analyzer, 9 khz to 13.6 GHz R&S FSG Signal Analyzer, 9 khz to 3.6 GHz R&S FSV Signal Analyzer, 9 khz to 7 GHz R&S FSV Signal Analyzer, 9 khz to 13.6 GHz R&S FSV Signal Analyzer, 9 khz to 30 GHz R&S FSV Signal Analyzer, 9 khz to 40 GHz R&S FSV Real-Time Spectrum Analyzer, 10 Hz to 7 GHz R&S FSVR Real-Time Spectrum Analyzer, 10 Hz to 13.6 GHz R&S FSVR Real-Time Spectrum Analyzer, 10 Hz to 30 GHz R&S FSVR Real-Time Spectrum Analyzer, 10 Hz to 40 GHz R&S FSVR Spectrum Analyzer, 20 Hz to 3.6 GHz R&S FSU Spectrum Analyzer, 20 Hz to 8 GHz R&S FSU Spectrum Analyzer, 20 Hz to 26.5 GHz R&S FSU Spectrum Analyzer, 20 Hz to 43 GHz R&S FSU Spectrum Analyzer, 20 Hz to 46 GHz R&S FSU Spectrum Analyzer, 20 Hz to 50 GHz R&S FSU Signal Source Analyzer, 20 Hz to 8 GHz R&S FSUP Signal Source Analyzer, 20 Hz to 26.5 GHz R&S FSUP Signal Source Analyzer, 20 Hz to 50 GHz R&S FSUP Recommended options and extras I/Q Bandwidth Extension R&S FSQ-B MHz Analysis Bandwidth R&S FSV-B Vector Signal Analyzer (mandatory for R&S FSU) R&S FSU-B See also specifications for the R&S FSW signal and spectrum analyzer (PD ), R&S FSQ signal analyzer (PD ), R&S FSG spectrum analyzer (PD ), R&S FSV spectrum analyzer (PD ), R&S FSVR real-time spectrum analyzer (PD ), R&S FSU spectrum analyzer (PD ) and R&S FSUP signal source analyzer (PD ). Rohde & Schwarz R&S FS-K130PC Distortion Analysis Software 7

8 Service that adds value Worldwide Local and personalized Customized and flexible Uncompromising quality Long-term dependability About Rohde & Schwarz The Rohde & Schwarz electronics group is a leading supplier of solutions in the fields of test and measurement, broadcasting, secure communications, and radiomonitor ing and radiolocation. Founded more than 80 years ago, this independent global company has an extensive sales network and is present in more than 70 countries. The company is headquartered in Munich, Germany. Sustainable product design Environmental compatibility and eco-footprint Energy efficiency and low emissions Longevity and optimized total cost of ownership Certified Quality Management ISO 9001 Certified Environmental Management ISO Rohde & Schwarz GmbH & Co. KG R&S is a registered trademark of Rohde & Schwarz GmbH & Co. KG Trade names are trademarks of the owners PD Version March 2014 (as) R&S FS-K130PC Distortion Analysis Software Data without tolerance limits is not binding Subject to change Rohde & Schwarz GmbH & Co. KG Munich, Germany PDP 1 en Regional contact Europe, Africa, Middle East customersupport@rohde-schwarz.com North America TEST RSA ( ) customer.support@rsa.rohde-schwarz.com Latin America customersupport.la@rohde-schwarz.com Asia/Pacific customersupport.asia@rohde-schwarz.com China / customersupport.china@rohde-schwarz.com FS-K130PC_dat-sw_en_ _cover.indd :46:16